Search Results

Search found 9516 results on 381 pages for 'duplicate resource'.

Page 297/381 | < Previous Page | 293 294 295 296 297 298 299 300 301 302 303 304  | Next Page >

• DRBD Replication failure

  - by user62513

  A couple of weeks ago I setup a 2 nodes CRM system with one of the resources managed being MySQL over DRBD. Today for maintenance reasons I restarted both nodes but now they can't connect to each other anymore. DRBD fell out of sync and I followed this guide to get it back connected but it's only able to run successfully on one node. But this strange thing happens: If I crm node standby both nodes and I try: crm node online node0 before crm node online node1, all the CRM resources start successfully but the DRBD partitions are still running in StandAlone state. crm node online node1 beofre crm node online node0, the DRBD resource fails to start, thus causing mysql not to start. If I standby both resources and call crm node online node0 then it times out and prints this error: Running crm node online node0 produces this output after timing out Error setting standby=off (section=nodes, set=<null>): Remote node did not respond Error performing operation: Remote node did not respond Is there anything I'm doing wrong here? An alternative will be just do MySQL replication but I'm not sure how to promote a slave to master when the master database is not available.

  Read the article

• will heavy network traffic affect other connections on HP ProCurve V1810-48G?

  - by nn4l

  I have a HP ProCurve V1810-48G switch with a few servers connected to it (everything in one rack). The switch is practically in its default configuration. During copying of a few hundred GByte of data from server_a to server_b (using tar cf - data | ssh server_b 'cd myhome; tar xf -'), essentially saturating the network capacity between those two servers, I noticed network related error messages on the console of server_c - as if server_c is no longer able to send/receive traffic to server_d. After canceling the copy command everything was normal again. I would understand this if the network connection would use a shared resource, for example if server_a and server_c are in one datacenter, server_b and server_d are in another datacenter and both datacenters are connected with a 100 MBit line. But all of the mentioned servers are connected to the same switch and are located in the same IP network. I always thought that a connection between two servers on one switch will not affect any other server connected to the switch. It is also possible that the network related error messages are caused by something else - but I can't risk a network problem for any other system on this switch. Please advise.

  Read the article

• Why is it bad to map network drives in Windows?

  - by Beeblebrox

  There has been some spirited discussion within our IT department about mapping network drives. In particular, it has been said that mapping network drives is A Bad Thing and that adding DFS paths or network shares to your (Windows Explorer/Libraries) Favourites is a far better solution. Why is this the case? Personally I find the convenience of z:\folder to be better than \\server\path\folder', particularly with cmd line and scripting (of course I'm not talking about hard-coded links, naturally!). I have tried searching for pros and cons of mapped network drives, but I haven't seen anything other than 'should the network go down, the drive will be unavailable'. But this is a limitation of any network-accessed storage... I have also been told that mapped network drives poll the network when the network resource is unavailable, however I haven't found more information on this. Wouldn't this still be an issue with other network access mechanisms (that is, mapped Favourites) whenever Windows tries to enumerate the file system (for example, when a file/folder picker dialog is opened)? -- Do network drives poll the network any more than a Windows Explorer library/favourite?

  Read the article

• Is it possible to add/register an MIB for the Windows built-in SNMP service?

  - by michielvoo

  I need to build monitoring into an existing .NET application. I will use SNMP to send the application's status to the Windows SNMP service. I have used a .NET library to create the SNMP SET request according to the MIB that I have been provided with, and with the correct community. My code now sends multiple 'variables' in a SET request, for example: Id: ".1.3.6.1.4.1.43607.1.1.1.1.1" (ObjectIdentifier) Data: 42 (Integer32) On my machine I have enabled the SNMP service, configured a community with READ/WRITE permissions, and added localhost to the list of hosts to accept requests from. When I send the SET request I get a response, but it has error status 17 which, according to MSDN means SNMP_ERRORSTATUS_NOTWRITABLE. The response also has error index set to 8, which is the number of variables I send. If I send 7 variables, the error index is set to 7. I think the problem is that the Windows SNMP service is preconfigured to only accept SET requests for a fixed set of MIBs. How can I get the Windows SNMP service to 'accept' my custom MIB SET request? Edit: I downloaded and installed the Windows Server 2003 Resource Kit and tried to 'compile' the MIB file with mibcc.exe ("SNMP MIB Compiler") but I have not been able to compile any MIB files (even the most basic ones like SNMPv2-SMI.mib).

  Read the article

• Extremely high mysqld CPU usage with no active queries

  - by RadarNyan

  I have a VPS running Ubuntu 12.04 LTS with LEMP stack, followed the guide from Linode Library (since I'm using a Linode) to setup, and everything worked fine until now. I don't know what's wrong, but my CPU usage just goes up since a week ago. Today things getting really bad - I got 74% CPU usage so I went check and found that mysqld taking too much CPU usage (somewhere around 30% ~ 80%) So I did some Google Search, tried disable InnoDB, restart mysql, reset ntp / system clock (Isn't this bug supposed to happen more than a year ago?!) and reboot my VPS, nothing helped. Even with mysql processlist empty, I still get mysqld CPU usage very high. I don't know what I missed and have totally no idea, any advice would be appreciated. Thanks in advance. Update: I got these from running "strace mysqld" write(2, "InnoDB: Unable to lock ./ibdata1"..., 44) = 44 write(2, "InnoDB: Check that you do not al"..., 115) = 115 select(0, NULL, NULL, NULL, {1, 0}^[[A^[[A) = 0 (Timeout) fcntl64(3, F_SETLK64, {type=F_WRLCK, whence=SEEK_SET, start=0, len=0}, 0xbfa496f8) = -1 EAGAIN (Resource temporarily unavailable) hum... I did tried to disable InnoDB and it didn't fix this problem. Any idea? Update2: # ps -e | grep mysqld 13099 ? 00:00:20 mysqld then use "strace -p 13099", the following lines appears repeatedly: fcntl64(12, F_GETFL) = 0x2 (flags O_RDWR) fcntl64(12, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(12, {sa_family=AF_FILE, NULL}, [2]) = 14 fcntl64(12, F_SETFL, O_RDWR) = 0 getsockname(14, {sa_family=AF_FILE, path="/var/run/mysqld/mysqld.sock"}, [30]) = 0 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0", 8) = 0 fcntl64(14, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) futex(0xb786a584, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0xb786a580, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0xb7869998, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=12, revents=POLLIN}]) er... now I totally don't get it x_x help

  Read the article

• Cloning a NAS drive which hosts a SQL Server DB

  - by Adrian Hand

  We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

  Read the article

• Why does Windows XP (during a rename operation) report file already exists when it doesn't?

  - by Hawk

  From the command-line: E:\menu\html\tom\val\.svn\tmp\text-base>ver Microsoft Windows [Version 5.2.3790] E:\menu\html\tom\val\.svn\tmp\text-base>dir Volume in drive E is DATA Volume Serial Number is F047-F44B Directory of E:\menu\html\tom\val\.svn\tmp\text-base 12/23/2010 04:36 PM <DIR> . 12/23/2010 04:36 PM <DIR> .. 12/23/2010 04:01 PM 0 wtf.com3.csv.svn-base 1 File(s) 0 bytes 2 Dir(s) 170,780,262,400 bytes free E:\menu\html\tom\val\.svn\tmp\text-base>rename wtf.com3.csv.svn-base com3.csv.svn-base A duplicate file name exists, or the file cannot be found. E:\menu\html\tom\val\.svn\tmp\text-base>dir Volume in drive E is DATA Volume Serial Number is F047-F44B Directory of E:\menu\html\tom\val\.svn\tmp\text-base 12/23/2010 04:36 PM <DIR> . 12/23/2010 04:36 PM <DIR> .. 12/23/2010 04:01 PM 0 wtf.com3.csv.svn-base 1 File(s) 0 bytes 2 Dir(s) 170,753,064,960 bytes free E:\menu\html\tom\val\.svn\tmp\text-base>` I don't know what to do about this, as there is no other file in this directory. Why does Windows XP report that there is already a file here named com3.csv.svn-base when there is clearly no other file here?

  Read the article

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

• Windows Action Center notification icon says Backup in Progress when no backup is occurring

  - by allquixotic

  How can I get Windows Action Center's little flag in the notification area to stop saying "Backup In Progress" on Windows 8? It's driving me nuts. I disabled the Windows Backup service completely and turned off File Recovery. Nothing that I can tell is using any disk I/O whatsoever, by examining Task Manager's resource monitor. It's just a visual cue that seems totally wrong considering my disk is only using about 50 KB/s of sporadic writes for superfetch etc. This wouldn't be a problem for me, since I rely on the knowledge that the Backup service is disabled and there's no disk activity, but I am trying to support a more traditional user who relies on visual cues from the operating system and trusts them over low-level observations like "...but the Windows Backup service is disabled!" Therefore this user still thinks that the backup is going on, even after the service is disabled. Technically, I think this is a bug in Windows 8. It really should not be displaying "Backup in Progress" if ... you know ... a backup, is not, in progress. Which it isn't. Is there a workaround?

  Read the article

• Malicious content on server - next steps advice [closed]

  - by Under435

  Possible Duplicate: My server's been hacked EMERGENCY I just got an e-mail from my hosting company that they got a report of malicious content being hosted on my vps. I was unaware of this and started looking into it. I discovered a file called /var/www/mysite.com/osc.htm. Soon after I discovered some weird php files wp-includes.php and ndlist.php both recognized as being PHP/WebShell.A.1 virus. I removed all these files but I'm unsure of what to do next. Can anyone help me analyze the output below of sudo netstat -A inet -p -e and give advice on what's best to do next. Thanks very much in advance Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 localhost.localdo:mysql localhost.localdo:37495 TIME_WAIT root 0 - tcp 0 1 mysite.com:50524 xnacreators.net:smtp SYN_SENT Debian-exim 69746 25848/exim4 tcp 0 0 mysite.com:www tha165.thehealtha:37065 TIME_WAIT root 0 - tcp 0 0 localhost.localdo:37494 localhost.localdo:mysql TIME_WAIT root 0 - udp 0 0 mysite.com:59447 merlin.ensma.fr:ntp ESTABLISHED ntpd 3769 2522/ntpd udp 0 0 mysite.com:36432 beast.syus.org:ntp ESTABLISHED ntpd 4357 2523/ntpd udp 0 0 mysite.com:48212 formularfetischiste:ntp ESTABLISHED ntpd 3768 2522/ntpd udp 0 0 mysite.com:46690 formularfetischiste:ntp ESTABLISHED ntpd 4354 2523/ntpd udp 0 0 mysite.com:35009 stratum-2-core-a.qu:ntp ESTABLISHED ntpd 4356 2523/ntpd udp 0 0 mysite.com:58702 stratum-2-core-a.qu:ntp ESTABLISHED ntpd 3770 2522/ntpd udp 0 0 mysite.com:49583 merlin.ensma.fr:ntp ESTABLISHED ntpd 4355 2523/ntpd udp 0 0 mysite.com:56290 beast.syus.org:ntp ESTABLISHED ntpd 3771 2522/ntpd

  Read the article

• Port 22 is not responding

  - by Emanuele Feliziani

  I'm trying to make the jump to VPS from shared hosting for better performances and greater flexibility, but am stuck with the fact that I can't access the machine via ssh. First of all, the machine is a CentOS 6.3 cPanel x64 with WHM 11.38.0. Sshd is running (it appears in the current running processes). Making a port scan I see that port 22 is not responding. Port 21 is, but I am not able to access the machine via ftp (I think it's a security measure, but I don't know where to disable/enable it). So, I'm stuck in WHM and have no way to access the configuration of the machine, neither via ssh nor with ftp/sftp. When trying to connect with ssh via Terminal I only get this: ssh: connect to host xx.xx.xxx.xxx port 22: Operation timed out I also tried to access with the hostname instead of the IP address and it's the same. There seem to be no firewall in WHM and I have whitelisted my home IP address to access ssh, though there were no restrictions in the first place. I have been wandering through all the settings and options in WHM for several hours now, but can't seem to find anything. Does anybody have a clue as to where I should start investigating? Update: Thanks everyone. It was in fact a matter of firewall. There was a firewall not controlled by the WHM software. I managed to crack into the console from the vps control panel (a terrible, terrible java app that barely took my keyboard input) and disabled the firewall altogether running service iptables stop so that I was able to access the console via ssh with the terminal. Now I will have to set up the firewall again because the command I ran looks like having completely wiped the iptables. Can you recommend any newby-friendly resource where I can learn how to go about this and what should I block? Or should I just go with something like this: http://configserver.com/cp/csf.html ? Thanks again to everyone who helped me out.

  Read the article

• Change Windows 7 Explorer's Details Pane limits

  - by Paul

  For some reason, MS decided to completely kill the status bar's functionality in Win7 (and maybe Vista, but I don't know for sure). I have tried all possible options such as Classic Shell and so on. Basically, the one thing I miss most is seeing at a glance the total size of my selected files. I know I can press Alt+Enter or whatever, but that's not the point. The point is that the so-called 'details' pane stops providing details if more than 15 files are selected! WTH? Cannot understand the reason behind such a stupid arbitrary limit, that doesn't seem to be user-configurable at all. Anyway, what I'm looking for is a way to change that limit, either via the registry or otherwise. If changing the limit isn't possible, would it be possible for some programming genius to create a very small optimized light-weight non resource-hungry (you get the idea!) program whose sole purpose will be to automatically click the "Show more details..." link in the details pane after every file selection? For bonus points, the program should wait for a second or two after file selection is complete to do this, so that selecting multiple files in quick succession doesn't hit the HDD repeatedly. Any takers for the challenge? :)

  Read the article

• Deploying ASP.NET MVC to Windows Server 2003

  - by pete the pagan-gerbil

  Hi, I have a problem with an MVC 2 website on Windows Server 2003 running IIS 6. It is externally hosted, but we have a 2003 server internally for testing. The internal server runs the website fine, the external server gives a 403 ("website declined to show this page") error when navigating to the root of the site, and a 404 if I try to navigate directly to a page resource. I have tried the wildcard ISAPI mapping and extension mapping, and a couple of other common checks (I forget exactly which now, most of them were already set correctly), but so far no joy. All the settings can be replicated on our internal server and the pages return properly. IIS logs just show exactly what the browser shows - 404 errors and 403s. I've read about a different level of trust required for an MVC application compared to a WebForms application - how can I check permissions and trust levels on the external and internal servers (assuming I am able to check that) and if that would cause these errors, what are the minimum levels that MVC require? Failing that, what else might be causing this error for me to try out?

  Read the article

• Microsoft Licensing Scenario/Questions [closed]

  - by user17455

  Possible Duplicate: Can you help me with my software licensing question? I am a member of a team developing a third party application (APP) that listens for and services connections from remote devices via TCP. Also, some of these remote devices allow 1 or more users to interact with the remote device. On some of the remote devices, it is impossible for a user to interact with the device. The user/remote device makes no use of any Windows Server service - not DHCP, not IIS, not File Server, not Print Serer, not AD. The remote device's only connection to the Windows Server machine is through the APP's TCP ports. Our company has no interaction with Microsoft. We do not have a Microsoft sales team. Past inquiries have determined that it is cheaper for us to buy Microsoft software (and CALs) retail than to enter into any kind of "arrangement" with Microsoft. I have many questions about SQL Server CALs and Windows Server 2008 CALs. How can I obtain authoritative/legally binding answers? I am not looking for FREE legal advice. I AM looking for FREE advice about who/what/where I can responsibly spend my money to get meaningful information. I fear that passing this on to the local company law firm will just mean that I will be paying them to educate themselves on Microsoft licensing. And if that's like writing code to a new Microsoft API - they are not going to get it right the first time. Going to Microsoft for answers sounds like swimming up to a hungry shark and asking "One leg or two?" I am hoping someone has been down this road before and knows a law firm/lawyer that is experienced in these matters. Any help/suggestion welcome. Thanks.

  Read the article

• Enabled Network Discovery on Server, and now VNC and Squeezebox clients don't work

  - by Mike Hanson

  I've recently setup a Windows Server 2008. It's running an email server, Squeezebox server, MS SQL Server, etc. I'm doing remote maintenance with UltraVNC. I had everything working fine. Then the server needed to access a network share on another machine, and I was prompted to turn on network discovery, which I did. I chose the Home rather than Public option. Since doing that, some things have stopped working, while others are still fine. Shared folders and the the Email services (ports 25 and 110) are still accessible. VNC (port 5900) and Squeezeboxes (port 9000) no longer work. Here's what I've tried to try to solve the problem: Checked the network discovery settings, to see if anything looked strange. Checked the firewall settings, and those ports appear to be open. Also in the firewall settings, the entries for Private domain Network Discovery were all on, but the Domain/Public ones were off. I tried turning those on. In the services, turned on Function Discovery Resource Publication and SSDP Discovery. Any other suggestions?

  Read the article

• Should tripwire be entering /proc?

  - by dsadinoff

  When initializing the db with tripwire --init it spat out a bunch of errors pertaining to /proc: ### Warning: File system error. ### Filename: /proc/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: Duplicate object encountered. ### /proc/sys/net/ipv6/neigh This feels like noise. The twpol.txt file has the following clause: # # Critical devices # ( rulename = "Devices & Kernel information", severity = $(SIG_HI), ) { /dev -> $(Device) ; /proc -> $(Device) ; } Which, if I understand it right, is going to cause tripwire to care deeply about the entire contents of /proc. Shouldn't it just care about the static parts of /proc like the drivers and such, and not the per-pid stuff? Why does it ship like this?

  Read the article

• ORA- 01157 / Cant connect to database

  - by Tom

  Hi everyone, this is a follow up from this question. Let me start by saying that i am NOT a DBA, so i'm really really lost with this. A few weeks ago, we lost contact with one of our SID'S. All the other services are working, but this one in particular is not. What we got was this message when trying to connect ORA-01033: ORACLE initialization or shutdown in progress An attempt to alter database open ended up in ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' I tried to shutdown / restart the database, but got this message. Total System Global Area 566231040 bytes Fixed Size 1220604 bytes Variable Size 117440516 bytes Database Buffers 444596224 bytes Redo Buffers 2973696 bytes Database mounted. ORA-01157: cannot identify/lock data file 6 - see DBWR trace file ORA-01110: data file 6: '/u01/app/oracle/oradata/xxx/xxx_data.dbf' When all continued the same, I erased the dbf files (rm xxx_data.dbf xxx_index.dbf), and recreated them using touch xxx_data.dbf. I also tried to recreate the tablespaces using `CREATE TABLESPACE DATA DATAFILE XXX_DATA.DBF` and got Database not open As I said, i don't know how bad this is, or how far i'm from gaining access to my database (well, to this SID at least, the others are working). I would imagine that a last resource would be to throw everything away, and recreating it, but I don't know how to, and I was hoping there's a less destructive solution. Any help will be greatly appreciated . Thanks in advance.

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• Windows file association for README, INSTALL, LICENSE and the like [closed]

  - by Lumi

  Possible Duplicate: How to set the default program for opening files without an extension in Windows? Many files originating in the UNIX world come without file extension. Popular examples include README, INSTALL, LICENSE. We know for a fact that these are text files. It is therefore a bit disappointing not to be able to just double-click them open in Explorer and see them in Notepad (actually, Notepad2 because of the UNIX line endings which silly Microsoft Notepad doesn't render correctly). Does anyone know of a way to create a file association for, say, README files without extension? This could then be replicated to cover the most frequently occurring file types, and then double-clicking them open would work. Update (Sort of in response to all your comments.) Thanks, folks, your comments and answers have helped me. @Indrek, yes, I was under the assumption that you could somehow create an association for just README or Makefile, and couldn't do so for files without extension. Turns out the contrary is true, and yes, that is a workaround that neatly solves the issue. Ultimately, I just want to be able to double-click to open a README or Makefile, that's all. @Sampo, the SendMe trick is also useful, although usability is not as great as a straight double-click. (I'm really lazy sometimes.) Turns out the following trick using ftype and ftype from an Administrator prompt does the double-click enabling job: assoc .=no_ext ftype no_ext=%SystemRoot%\system32\NOTEPAD.EXE %1 :: You can see it created some entries in the registry: reg query hkcr\no_ext /s reg query hkcr\. /s

  Read the article

• DRBD setup problem

  - by cuthieu

  I'm so new to DRBD, please help me fixing the problem below. Enclosed my drbd.conf. Many thanks [root@skonkwerks1 ~]# drbdadm create-md all open(/dev/hdb3) failed: No such file or directory Command 'drbdmeta /dev/drbd0 v08 /dev/hdb3 internal create-md' terminated with exit code 20 drbdsetup exited with code 20 [root@skonkwerks1 ~]# vi /etc/drbd.conf global { usage-count no; } resource repdata { protocol C; startup { wfc-timeout 0; degr-wfc-timeout 120; } disk { on-io-error detach; } # or panic # net { cram-hmac-alg "hdd1"; shared-secret "testing"; } syncer { rate 10M; } on skonkwerks1 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.1:7788; meta-disk internal; } on skonkwerks2 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.2:7788; meta-disk internal; } }

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

• Diagnosing "The specified module could not be found" on IIS7 with ASP.Net

  - by Baldy

  I am migrating some web apps from a windows 2003 server with IIS6 server to a Windows server 2008 R2 server with IIS7. One of the apps, which runs on asp.net v2.0 using forms authentication will not load. It gives me the following error... The specified module could not be found. (Exception from HRESULT: 0x8007007E) Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.IO.FileNotFoundException: The specified module could not be found. (Exception from HRESULT: 0x8007007E) Now i fully understand that the app cannot load some kind of resource due to a FileNotFoundException, but i am struggling to diagnose exactly where in the application this is happening, as it does not tell me what the module is, nor what file it is looking for. I have enabled failed request tracing and i get back a complete request trace, yet i cannot find anything that gives me detail on this specific error, or the module involved. Any advice on diagnosing the root cause of the issue would be greatly appreciated.

  Read the article

• VMM 2012 Adding Hosts in Trusted Forest

  - by Steve Evans

  I have two forests with a two way trust between them. VMM 2012 sits in ForestA and I can discover hosts in ForestA with no issue. When I try to discover hosts in ForestB I hit one of two issues: If I go through the GUI or use Powershell just like I normally do I get the following error on the job: Error (10407) Virtual Machine Manager could not query Active Directory Domain Services. Recommended Action Verify that the domain name and the credentials, if provided, are correct and then try the operation again. It doesn't matter which account I use. I've tried accounts from both forests, with Admin/Domain Admin permissions all over the place, etc Going through the GUI (can't find the switch in Powershell to duplicate this), I check the box "Skip AD Verification" and it causes the GUI to crash during discovery. I found an article (http://technet.microsoft.com/en-us/library/gg610641.aspx) that describes how to add a host in a disjoint namespace (even though that doesn't apply to me) and it says that VMM creates an SPN if one does not exist. So I verified that the correct SPN's exist in ForestB, that did not help the issue. I have a case open with PSS but they are stuck. I have VMM traces if anyone would like to see them. Any suggestions or ideas?

  Read the article

• Sharepoint AD imported users are becomming sporadically corrupted, causing us to have to create a ne

  - by TrevJen

  Sharepoint 2007 MOSS with AD imported users. All servers are 2008. I have around 50 users, over the past 2 months, I have had a handful of the users suddenly unable to login to Sharepoint. When they login, they either get a blank screen or they are repropmted. These users are using accounts that have been used for many months, sometimes the problem originates with a password change. In all cases, the users account works on every other Active Directory authenticated resource (domain, exchange, LDAP). In the most recent case, last night I was forced deleted a user ("John smith") because of corruption. The orifinal account name was jsmith. I deleted him from active directory, then deleted him from the profile list in Sharepoint Shared Services. I could not find a way to delete him from the Sharepoint user list, but I reran the import after recreating his account (renamed it too just to be sure to "smithj"). At first, this did not wor, the user could still access all other resources but Sharepoint. then, some 30 minutes later it inexplicably started working. This morning, the user changed passwords, which immediatly broke the login on Sharepoint again. I am at a loss on how to troubleshoot this.

  Read the article

< Previous Page | 293 294 295 296 297 298 299 300 301 302 303 304  | Next Page >