Search Results

Search found 8831 results on 354 pages for 'intel graphics'.

Page 298/354 | < Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >

• ZTE USB Modem AC2736, connection not possible in Ubuntu 12.04.1 LTS

  - by Fredo

  It's a long post but nearly covers all my experiments and changes I did to my NM. Hope the information is complete and if there are still question, more information can be provided. I've a ZTE AC2736 USB Modem (CDMA modem) which worked fine in Ubuntu 10.04 /11.10. I recently switched to 12.04.1 (precise pangolin). after the switch the first issue I faced was to connect to internet using my USB modem (ISP: Reliance Brand: Netconnect). Tried to run the drivers provided by Reliance but they are old and won't support Kernel 2.6.30 above. since the code was not downloaded with ISO image (of 12.04) i couldn't compile the files provided in such driver. lsusb does detect it as Modem with output similar to 19d2:fff1 ZTE CDMA technologies inc. (or similar as i didn't note it down) If it is detected as USB storage it shows 19d2:fff5 (as per few online forums, i may be wrong here). I used the network Manager and configured the modem to dial #777 (default) and the ISP provided username:password combination. It tries to connect to internet (3-4 times automatically)but fails to get online. once I was able to connect in the monring hours and the message was flashed 'registered on CDMA home network'. I was able to run an update. the kernel was updated with 3.0.2 -pae OR something similar (can find out if required). I surfed the net for about 2 hours later before restarting. After the restart, again the Modem was not able to get me online. I kept trying for many times. I tried changing the setting in NM. One evening after dark I was able to connect to network with same message flash 'registered on CDMA home network' (the message was similar, i'm not precise here,sorry). I was able to surf the net for nearly 3 hours before I switched off my Laptop. I'm not able to get online after that day, It's been 3 days now. I'll try the observered theory of late/early hours sometime soon as mentioned below. Laptop configuration : Make: Lenovo Model: B480 Processor: Intel B950 RAM: 4G DDR3 HDD: 500 G Broadcom Wireless/Bluetooth/Ethernet LAN OS: FreeDOS / Ubuntu 12.04 LTS (dualboot) Kernel 3.0.2-pae Obeservation : I'm able to connect to internet in those hours when generally the speed is high (low usage by other network (wireless) users). like in early mornings or late nights. This is strange as connection should not be dependent on bandwidth usage. Any help would be appraciated to fix this issue. before I decide to cahnge the OS or ISP.

  Read the article

• A Slice of Raspberry Pi

  - by Phil Factor

  Guest editorial for the ITPro/SysAdmin newsletter The Raspberry Pi Foundation has done a superb design job on their new $35 network-enabled Linux computer. This tiny machine, incorporating an ARM processor on a Broadcom BCM2835 multimedia chip, aims to put the fun back into learning computing. The public response has been overwhelmingly positive.Note that aim: "…to put the fun back". Education in Information Technology is in dire straits. It always has been, but seems to have deteriorated further still, even in the face of improved provision of equipment.In many countries, the government controls the curriculum. It predicted a shortage in office-based IT skills, and so geared the ICT curriculum toward mind-numbing training in word-processing and spreadsheet skills. Instead, the shortage has turned out to be in people with an engineering-mindset, who can solve problems with whatever technologies are available and learn new techniques quickly, in a rapidly-changing field.In retrospect, the assumption that specific training was required rather than an education was an idiotic response to the arrival of mainstream information technology. As a result, ICT became a disaster area, which discouraged a generation of youngsters from a career in IT, and thereby led directly to the shortage of people with the skills that are required to exploit the potential of Information Technology..Raspberry Pi aims to reverse the trend. This is a rig that is geared to fast graphics in high resolution. It is no toy. It should be a superb games machine. However, the use of Fedora, Debian, or Arch Linux ARM shows the more serious educational intent behind the Foundation's work. It looks like it will even do some office work too!So, get hold of any power supply that provides a 5VDC source at the required 700mA; an old Blackberry charger will do or, alternatively, it will run off four AA cells. You'll need a USB hub to support the mouse and keyboard, and maybe a hard drive. You'll want a DVI monitor (with audio out) or TV (sound and video). You'll also need to be able to cope with wired Ethernet 10/100, if you want networking.With this lot assembled, stick the paraphernalia on the back of the HDTV with Blu Tack, get a nice keyboard, and you have a classy Linux-based home computer. The major cost is in the T.V and the keyboard. If you're not already writing software for this platform, then maybe, at a time when some countries are talking of orders in the millions, you should consider it.

  Read the article

• Create USB installer from the command line?

  - by j-g-faustus

  I'm trying to create a bootable USB image to install Ubuntu on a new computer. I have done this before following the "create USB drive" instructions for Ubuntu desktop, but I don't have an Ubuntu desktop available. How can I do the same using only the command line? Things I've tried: Create bootable USB on Mac OS X following the ubuntu.com "create USB drive" instructions for Mac: Doesn't boot. usb-creator: According to apt-cache search usb-creator and Wikipedia usb-creator only exists as a graphical tool. "Create manually" instructions at help.ubuntu.com: None of the files and directories described (e.g. casper, filesystem.manifest, menu.lst) exist in the ISO image, and I don't know what has replaced them. unetbootin scripting: Requires X server (graphics support) to run, even when fully scripted. (The command sudo unetbootin lang=en method=diskimage isofile=~/ubuntu-10.10-server-amd64.iso installtype=USB targetdrive=/dev/sdg1 autoinstall=yes gives an error message unetbootin: cannot connect to X server.) Update Also tried GRUB fiddling: Merging information from pendrivelinux.com a related question on the Linux Stackexchange and a grub configuration example I was able to get halfway there - it booted from USB, displayed the grub menu and started the installation, but installation did not complete. For reference, this is the closest I got: sudo su # mount USB pen mount /dev/sd[X]1 /media/usb # install GRUB grub-install --force --no-floppy --root-directory=/media/usb /dev/sd[X] # copy ISO image to USB cp ~/ubuntu-10.10-server-amd64.iso /media/usb # mount ISO image, copy existing grub.cfg mount ~/ubuntu-10.10-server-amd64.iso /media/iso/ -o loop cp /media/iso/boot/grub/grub.cfg /media/usb/boot/grub/ I then edited /media/usb/boot/grub.cfg to add an .iso loopback, example grub entry: menuentry "Install Ubuntu Server" { set gfxpayload=keep loopback loop /ubuntu-10.10-server-amd64.iso linux (loop)/install/vmlinuz file=(loop)/preseed/ubuntu-server.seed iso-scan/filename=/ubuntu-10.10-server-amd64.iso quiet -- initrd (loop)/install/initrd.gz } When booting from USB, this would give me the Grub boot menu and start the installer, but the installer gave up after a couple of screens complaining that it couldn't find the CD-ROM drive. (Naturally, as the box I'm installing on doesn't have an optical drive.) I resolved this particular issue by giving up and doing the "create USB drive" routine using the Ubuntu Live desktop CD (on a computer that does have an optical drive), then the USB install works. But I expect that there is some way to do this from the command line of an Ubuntu system without X server and without an optical drive, so the question still stands. Does anyone know how?

  Read the article

• Ubuntu 12.10 Trackpoint not detected Thinkpad X130e

  - by killerknives

  I just did a fresh install of 12.10 and now only my touchpad works. The trackpoint and Left/Right buttons below the trackpoint do not work. The trackpoint worked fine as of 12.04. I've searched online and there was a hack that said that disabling the touchpad would enable the trackpoint. WRONG! You'll end up having to use the keyboard =/. I don't know what is needed so I'll just dump some stuff. lspci: 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:06.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:07.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 01:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) I've installged gpointing-device-setting and it only lists the touchpad. No trackpoint. What should I do? What data do you need?

  Read the article

• Draw a never-ending line in XNA

  - by user2236165

  I am drawing a line in XNA which I want to never end. I also have a tool that moves forward in X-direction and a camera which is centered at this tool. However, when I reach the end of the viewport the lines are not drawn anymore. Here are some pictures to illustrate my problem: At the start the line goes across the whole screen, but as my tool moves forward, we reach the end of the line. Here are the method which draws the lines: private void DrawEvenlySpacedSprites (Texture2D texture, Vector2 point1, Vector2 point2, float increment) { var distance = Vector2.Distance (point1, point2); // the distance between two points var iterations = (int)(distance / increment); // how many sprites with be drawn var normalizedIncrement = 1.0f / iterations; // the Lerp method needs values between 0.0 and 1.0 var amount = 0.0f; if (iterations == 0) iterations = 1; for (int i = 0; i < iterations; i++) { var drawPoint = Vector2.Lerp (point1, point2, amount); spriteBatch.Draw (texture, drawPoint, Color.White); amount += normalizedIncrement; } } Here are the draw method in Game. The dots are my lines: protected override void Draw (GameTime gameTime) { graphics.GraphicsDevice.Clear(Color.Black); nyVector = nextVector (gammelVector); GraphicsDevice.SetRenderTarget (renderTarget); spriteBatch.Begin (); DrawEvenlySpacedSprites (dot, gammelVector, nyVector, 0.9F); spriteBatch.End (); GraphicsDevice.SetRenderTarget (null); spriteBatch.Begin (SpriteSortMode.Deferred, BlendState.AlphaBlend, null, null, null, null, camera.transform); spriteBatch.Draw (renderTarget, new Vector2 (), Color.White); spriteBatch.Draw (tool, new Vector2(toolPos.X - (tool.Width/2), toolPos.Y - (tool.Height/2)), Color.White); spriteBatch.End (); gammelVector = new Vector2 (nyVector.X, nyVector.Y); base.Draw (gameTime); } Here's the next vector-method, It just finds me a new point where the line should be drawn with a new X-coordinate between 100 and 200 pixels and a random Y-coordinate between the old vector Y-coordinate and the height of the viewport: Vector2 nextVector (Vector2 vector) { return new Vector2 (vector.X + r.Next(100, 200), r.Next ((int)(vector.Y - 100), viewport.Height)); } Can anyone point me in the right direction here? I'm guessing it has to do with the viewport.width, but I'm not quite sure how to solve it. Thank you for reading!

  Read the article

• Audio Stutters at gdm

  - by Allan

  Ok I have a problem every 2 times out of 3 I login (I cant be specific it fairly random) I get a Stuttering GDM warning (not the login sound just the Bell sound to wake you up) the only way to stop it is to login I have a Fujitsu Siemens Amilo 1718 with a 2gig of memory (only hardware mod) using 10.10 Maverick and I have disabled KMS as my system was freezing as per the release notes. The only time this has happened before on the same machine was when I gave Kubuntu a try when 10.04 came out then it happened at the login screen and at random times while listening to music in any program. By the way audio is fine as is almost everything else once I have logged in. I would like an answer to this as I am an advocate of Ubuntu and its kind of embarrassing when the first thing that happens is *bing*. as requested Daniel alsa-info Pulse verbose log Not sure how useful the pulse log will be as I cant replicate the bug with a terminal open but I wouldnt be asking the question if I knew the answer so..... Edit 24/12/2010 ......been living on cocktail sausages and pickled onions for five days now made a make shift splint with cocktail sticks..... oops so updated the alsa drivers but I still get the same message in the dmesg No response from codec, disabling MSI: last cmd=0x10a90000 googleing it brings up a forum post from some other distro with a green logo the only common denominator seems to be graphics ie ATI Radeon XPRESS 200M which is why I have had to turn of kms as the chip is so old that small mice try to eat the "kernel" ;) funnily enough following the bug link at the end of the post, I found a comment about "Ubuntu Black Magic" so mabey I am coming at this from the wrong angle...... Bad Joo Joo any one. I will try the second part of Daniels Fix and Update with the result. The final Edit: (Plays air guitar) In the end neither of these solved the problem as such However I have given Roland a tick for reminding me of the solution and I gave Daniel the Bounty for the effort in trying to solve the problem. The answer for future readers was the enable the correct HD Audio Model I found the answer back when using Karmic Koala 9.10 in this forum post Amilo Li1718 Skype - Can't get it working... the model is options snd-hda-intel model=3stack position_fix=1 enable=yes which can be added to the end of alsa-base.conf thanks all for helping and hope anyone with a similar problem will find the answer here.

  Read the article

• Error message during update from 13.04 to 13.10

  - by layonhands

  The following was reported after I attempted to report the problem back to Ubuntu: The problem cannot be reported: You have some obsolete package versions installed. Please upgrade the following packages and check if the problem still occurs: ubuntu-release-upgrader-gtk, apport, apport-gtk, apport-symptoms, apt, apt-utils, at-spi2-core, binutils, dbus, gcc-4.7-base, gdb, gir1.2-atk-1.0, gir1.2-gtk-3.0, glib-networking, glib-networking-common, glib-networking-services, gnupg, gpgv, ifupdown, initramfs-tools, initramfs-tools-bin, kmod, libappindicator3-1, libapt-inst1.5, libapt-pkg4.12, libasound2, libatk-bridge2.0-0, libatk1.0-0, libatk1.0-data, libatspi2.0-0, libc-bin, libc6, libcups2, libdbus-1-3, libdbusmenu-glib4, libdbusmenu-gtk3-4, libdrm-intel1, libdrm-nouveau2, libdrm-radeon1, libdrm2, libgail-3-0, libgcc1, libgcrypt11, libglib2.0-0, libglib2.0-data, libgnutls26, libgomp1, libgstreamer-plugins-base1.0-0, libgstreamer1.0-0, libgtk-3-0, libgtk-3-bin, libgtk-3-common, libgudev-1.0-0, libicu48, libindicator3-7, libkmod2, liblcms2-2, libpci3, libplymouth2, libpolkit-agent-1-0, libpolkit-backend-1-0, libpolkit-gobject-1-0, libprocps0, libpython-stdlib, libpython2.7, libpython2.7-minimal, libpython2.7-stdlib, libpython3-stdlib, libpython3.3-minimal, libpython3.3-stdlib, libssl1.0.0, libstdc++6, libtiff5, libudev1, libx11-6, libx11-data, libx11-xcb1, libxcb-dri2-0, libxcb-glx0, libxcb-render0, libxcb-shm0, libxcb1, libxcursor1, libxext6, libxfixes3, libxi6, libxinerama1, libxml2, libxrandr2, libxrender1, libxres1, libxt6, libxtst6, libxxf86vm1, lsb-base, lsb-release, module-init-tools, multiarch-support, openssl, passwd, pciutils, perl, perl-base, perl-modules, plymouth, plymouth-theme-ubuntu-text, policykit-1, procps, python, python-gi, python-minimal, python2.7, python2.7-minimal, python3, python3-apport, python3-distupgrade, python3-gi, python3-minimal, python3-problem-report, python3-software-properties, python3-update-manager, python3.3, python3.3-minimal, rsyslog, shared-mime-info, software-properties-common, software-properties-gtk, tar, tzdata, ubuntu-release-upgrader-core, ubuntu-release-upgrader-gtk, udev, update-manager, update-manager-core, update-notifier, update-notifier-common If this question has already been answered, I'm sorry for the repost, but I would appreciate a link to the fix. Thanks. FYI: Dell Latitude D630, Intel Centrino processor. Also, the updater is currently running what seems to be the update. I will report back when it is done going through its process to let you know if it is in fact the 13.10 update. Update 2: System went through an update, but it wasn't for the OS. I think it was an update for the error message mentioned above. Now the OS update is currently running the 'distribution upgrade' portion of the update. This is further than it had gone before. Again I will report back once this is done to let you know whether or not the update was successful. Final Update: Don't know for sure what happened, but I'm almost sure that the error mentioned above was resolved in the first update prior to the 13.10 update. All set.

  Read the article

• Ubuntu won't display netbook's native resolution

  - by Daniel

  FYI: My Netbook model is HP Mini 210-1004sa, which comes with Intel Graphics Media Accelerator 3150, and has a display 10.1" Active Matrix Colour TFT 1024 x 600. I recently removed Windows 7 Starter from my netbook, and replaced it with Ubuntu 12.10. The problem is the OS doesn't seem to recognise the native display resolution of 1024x600 i.e. the bottom bits of Ubuntu is hidden beneath the screen & the only 2 available resolutions are: the default 1024x768 and 800x600. I've also thought about replacing Ubuntu with Lubuntu or Puppy Linux, as the system does run a bit slow, but I can't, as then I won't be able to access the taskbar and application menu which will be hidden beneath the screen. Only Ubuntu with Unity is currently usable, as the Unity Launcher is visible enough. I was able to define a custom resolution 1024x600 using the Q&A: How set my monitor resolution? but when I set that resolution, there appears a black band at the top of the screen and the desktop area is lowered, with bits of it hidden beneath the screen. I tried leaving it at this new resolution and restarting the system to see if the black band would disappear & the display will fit correctly, but it gets reset to 1024x768 at startup and displays following error: Could not apply the stored configuration for monitors none of the selected modes were compatible with the possible modes: Trying modes for CRTC 63 CRTC 63: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 0) CRTC 63: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 0) CRTC 63: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 0) CRTC 63: trying mode 1024x768@60Hz with output at 1024x600@60Hz (pass 1) CRTC 63: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 1) CRTC 63: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 1) CRTC 63: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 1) Trying modes for CRTC 64 CRTC 64: trying mode 1024x768@60Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 0) CRTC 64: trying mode 1024x768@60Hz with output at 1024x600@60Hz (pass 1) CRTC 64: trying mode 800x600@60Hz with output at 1024x600@60Hz (pass 1) CRTC 64: trying mode 800x600@56Hz with output at 1024x600@60Hz (pass 1) CRTC 64: trying mode 640x480@60Hz with output at 1024x600@60Hz (pass 1)

  Read the article

• Will polishing my current project be a better learning experience than starting a new one?

  - by Alejandro Cámara

  I started programming many years ago. Now I'm trying to make games. I have read many recommendations to start cloning some well known games like galaga, tetris, arkanoid, etc. I have also read that I should go for the whole game (including menus, sound, score, etc.). Yesterday I finished the first complete version of my arkanoid clone. But it is far from over. I can still work on it for months (I program as a hobby in my free time) implementing a screen resolution switcher, remap of the control keys, power-ups falling from broken bricks, and a huge etc. But I do not want to be forever learning how to clone ONE game. I have the urge to get to the next clone in order to apply some design ideas I have come upon while developing this arkanoid clone (at the same time I am reading the GoF book and much source code from Ludum Dare 21 game contest). So the question is: Should I keep improving the arkanoid clone until it has all the features the original game had? or should I move to the next clone (there are almost infinite games to clone) and start mending the things I did wrong with the previous clone? This can be a very subjective question, so please restrain the answers to the most effective way to learn how to make my own games (not cloning someone ideas). Thank you! CLARIFICATION In order to clarify what I have implemented I make this list: Features implemented: Bouncing capabilities (the ball bounces on walls, on bricks, and on the bar). Sounds when bouncing on bricks and the bar, and when the player wins or loses. Basic title menu (new game and exit only). Also in-game menu and win/lose menus. Only three levels, but the map system is so easy I do not think it will teach me much (am I wrong?). Features not-implemented: Power-ups when breaking the bricks. Complex bricks (with more than one "hit point" and invincible). Better graphics (I am not really good at it). Programming polishing (use more intensively the design patterns). Here's a link to its (minimal) webpage: http://blog.acamara.es/piperine/ I kind of feel ashamed to show it, so please do not hit me too hard :-) My question was related to the not-implemented features. I wondered what was the fastest (optimal) path to learn. 1) implement the not-implemented features in this project which is getting big, or 2) make a new game which probably will teach me those lessons and new ones. ANSWER I choose @ashes999 answer because, in my case, I think I should polish more and try to "ship" the game. I think all the other answers are also important to bear in mind, so if you came here having the same question, before taking a rush decision read all the discussion. Thank you all!

  Read the article

• Moving Character in C# XNA Not working

  - by Matthew Stenquist

  I'm having trouble trying to get my character to move for a game I'm making in my sparetime for the Xbox. However, I can't seem to figure out what I'm doing wrong , and I'm not even sure if I'm doing it right. I've tried googling tutorials on this but I haven't found any helpful ones. Mainly, ones on 3d rotation on the XNA creators club website. My question is : How can I get the character to walk towards the right in the MoveInput() function? What am I doing wrong? Did I code it wrong? The problem is : The player isn't moving. I think the MoveInput() class isn't working. Here's my code from my character class : using System; using System.Collections.Generic; using System.Linq; using System.Text; using Microsoft.Xna.Framework; using Microsoft.Xna.Framework.Graphics; using Microsoft.Xna.Framework.Input; namespace Jumping { class Character { Texture2D texture; Vector2 position; Vector2 velocity; int velocityXspeed = 2; bool jumping; public Character(Texture2D newTexture, Vector2 newPosition) { texture = newTexture; position = newPosition; jumping = true; } public void Update(GameTime gameTime) { JumpInput(); MoveInput(); } private void MoveInput() { //Move Character right GamePadState gamePad1 = GamePad.GetState(PlayerIndex.One); velocity.X = velocity.X + (velocityXspeed * gamePad1.ThumbSticks.Right.X); } private void JumpInput() { position += velocity; if (GamePad.GetState(PlayerIndex.One).Buttons.A == ButtonState.Pressed && jumping == false) { position.Y -= 1f; velocity.Y = -5f; jumping = true; } if (jumping == true) { float i = 1.6f; velocity.Y += 0.15f * i; } if (position.Y + texture.Height >= 1000) jumping = false; if (jumping == false) velocity.Y = 0f; } public void Draw(SpriteBatch spriteBatch) { spriteBatch.Draw(texture, position, Color.White); } } }

  Read the article

• Ubuntu Dual Screen Using Virtual Machine - AMD GPU

  - by Chris

  I've been searching online and reading tutorials and etc about how to make my ubuntu VM dual screen(x86_64). I have first tried to run these commands: sudo aticonfig --initial -f which gave me the ouput of: sudo: aitconfig: command not found I then googled the output and followed these instructions that I tells me to install my ATI drivers onto my ubuntu. wget http://www2.ati.com/drivers/linux/ati-driver-installer-11-5-x86.x86_64.run sudo sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Ubuntu/natty sudo dpkg -i *.deb sudo apt-get -f install sudo aticonfig -f --initial --adapter=all sudo reboot It all works well until I input sudo apt-get -f install which gives me the following output: sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 25 not upgraded. 3 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up fglrx (2:8.850-0ubuntu1) ... update-alternatives: error: alternative link /usr/bin/aticonfig is already managed by x86_64-linux-gnu_gl_conf. dpkg: error processing fglrx (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of fglrx-amdcccle: fglrx-amdcccle depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-amdcccle (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of fglrx-dev: fglrx-dev depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-dev (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: fglrx fglrx-amdcccle fglrx-dev E: Sub-process /usr/bin/dpkg returned an error code (1) At this point, I don't know what to do since running: gksudo amdcccle For the record, I have 3D acceleration turned on. The following is my GPU for my VM lspci | grep VGA 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter Any Help on how I can make my VM dual screen with Ubuntu would be great. Thank you in advance.

  Read the article

• Radeon HD 2000, 3000, 4000 on 12.10 Quantal: fglrx (legacy) 12.6 unsupported, what to do?

  - by Andrew Mao

  After upgrading to 12.10 quantal, the packaged version of fglrx no longer works. I discovered that this is because there is a separate 'legacy' fglrx driver for the HD 2k-4k series cards, but it is incompatible with the xorg server on 12.10. This is the most current version of the driver for HD 2000 through HD 4000 series cards. You can't use the non-legacy fglrx driver, but you can use the open-source radeon driver if you prefer your WM compositing to be laggy and your YouTube videos to play like they would on a Pentium MMX series: http://support.amd.com/us/kbarticles/Pages/catalyst126legacyproducts.aspx Usually this driver can be installed in the following way, necessary because apt-get install fglrx would pull in the non-legacy driver: wget http://www2.ati.com/drivers/legacy/amd-driver-installer-12.6-legacy-x86.x86_64.zip unzip amd-driver-installer-* sudo sh ./amd-driver-installer-*.run --buildpkg Ubuntu/quantal sudo dpkg -i fglrx*.deb sudo aticonfig --initial -f If you use a different version of fglrx (for example, a newer 12.9 that doesn't support those cards) then the final command will give you an error no supported hardware detected or something similar. However, everything works at this point and you will get a reasonable xorg.conf: ... other stuff Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:5:0" EndSection ... other stuff At this point you're supposed to reboot and everything will be working with the fglrx driver. However, upon rebooting, you'll be treated to the following errors in Xorg.0.log when fglrx attempts to load: (EE) Failed to load /usr/lib/xorg/modules/drivers/fglrx_drv.so: /usr/lib/xorg/modules/drivers/fglrx_drv.so: undefined symbol: noXFree86DRIExtension Some searching around will show that this is a problem with the legacy ATI drivers not supporting xserver 1.13 or newer. (Arch Linux thread) ATI has released a fixed driver for its most recent (HD 5000 series or later) cards, but not for the 'legacy' cards yet. The non-legacy ATI drivers can't be used with the old cards. What should an Ubuntu user, using one of these HD 2000-4000 series cards, do? Wait for an updated 'legacy' ATI driver that properly works with xserver 1.13? Downgrade back to 12.04 Precise, which uses xserver 1.11? Try to downgrade xserver on 12.10 Quantal to 1.12, which could possibly break Unity and GNOME? Forced upgrade to HD 5000 series or later card? (Not possible with integrated graphics...) Some other 1337 action that fixes this problem painlessly?

  Read the article

• Strange rendering in XNA/Monogame

  - by Gerhman

  I am trying to render G-Code generated for a 3d-printer as the printed product by reading the file as line segments and the drawing cylinders with the diameter of the filament around the segment. I think I have managed to do this part right because the vertex I am sending to the graphics device appear to have been processed correctly. My problem I think lies somewhere in the rendering. What basically happens is that when I start rotating my model in the X or Y axis then it renders perfectly for half of the rotation but then for the other half it has this weird effect where you start seeing through the outer filament into some of the shapes inside. This effect is the strongest with X rotations though. Here is a picture of the part of the rotation that looks correct: And here is one that looks horrible: I am still quite new to XNA and/Monogame and 3d programming as a whole. I have no idea what could possibly be causing this and even less of an idea of what this type of behavior is called. I am guessing this has something to do with rendering so have added the code for that part: protected override void Draw(GameTime gameTime) { GraphicsDevice.Clear(Color.Black); basicEffect.World = world; basicEffect.View = view; basicEffect.Projection = projection; basicEffect.VertexColorEnabled = true; basicEffect.EnableDefaultLighting(); GraphicsDevice.SetVertexBuffer(vertexBuffer); RasterizerState rasterizerState = new RasterizerState(); rasterizerState.CullMode = CullMode.CullClockwiseFace; rasterizerState.ScissorTestEnable = true; GraphicsDevice.RasterizerState = rasterizerState; foreach (EffectPass pass in basicEffect.CurrentTechnique.Passes) { pass.Apply(); GraphicsDevice.DrawPrimitives(PrimitiveType.TriangleList, 0, vertexBuffer.VertexCount); } base.Draw(gameTime); } I don't know if it could be because I am shading something that does not really have a texture. I am using this custom vertex declaration I found on some tutorial that allows me to store a vertex with a position, color and normal: public struct VertexPositionColorNormal { public Vector3 Position; public Color Color; public Vector3 Normal; public readonly static VertexDeclaration VertexDeclaration = new VertexDeclaration ( new VertexElement(0, VertexElementFormat.Vector3, VertexElementUsage.Position, 0), new VertexElement(sizeof(float) * 3, VertexElementFormat.Color, VertexElementUsage.Color, 0), new VertexElement(sizeof(float) * 3 + 4, VertexElementFormat.Vector3, VertexElementUsage.Normal, 0) ); } If any of you have ever seen this type of thing please help. Also, if you think that the problem might lay somewhere else in my code then please just request what part you would like to see in the comments section.

  Read the article

• Wireless not working on Dell Inspirion 1501 after upgrading to Ubuntu 12.04 tried steps in other threads

  - by mark burton

  I updated to Ubuntu 12.04 and now my wireless is not working. No icon for it. Tried some of the troubleshooting in other threads but can't get it to work. Would really appreciate any help Thanks! " *-network description: Network controller product: BCM4311 802.11a/b/g vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 02 serial: 00:19:b9:5c:d1:52 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=10.0.0.6 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff " lsub results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c526 Logitech, Inc. Nano Receiver $ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:05.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:06.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS482 [Radeon Xpress 200M] 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01) 08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 08:01.0 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 08:01.1 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01) rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• How to generate xorg.conf? (X -configure segfaults)

  - by Nicolas Raoul

  My video card is working fine, I have no screen problem. I am trying to generate an xorg.conf so I did: [ Logout ] sudo service gdm stop [ Move away xorg.conf.back and xorg.conf.fglrx-0 that were in /etc/X11 ] sudo dpkg-reconfigure xserver-xorg sudo X -configure But this last command segfaults: X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-27-server i686 Ubuntu Current Operating System: Linux nico 2.6.32-25-generic #44-Ubuntu SMP Fri Sep 17 20:26:08 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-25-generic root=UUID=7447ab16-3406-442d-81e5-bb6a2d795205 ro quiet splash Build Date: 21 July 2010 12:47:34PM xorg-server 2:1.7.6-2ubuntu7.3 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Fri Oct 15 16:06:11 2010 List of video drivers: i740 ark geode siliconmotion mach64 s3 r128 apm intel neomagic vesa trident chips s3virge fglrx sis savage rendition i128 tseng ztv mga openchrome radeon ati nv v4l vmware cirrus tdfx nouveau sisusb voodoo fbdev (EE) Can't load FireGL DRM library (libfglrxdrm.so). Backtrace: 0: X (xorg_backtrace+0x3b) [0x80e938b] 1: X (0x8048000+0x61c8d) [0x80a9c8d] 2: (vdso) (__kernel_rt_sigreturn+0x0) [0x34d410] 3: X (xf86CallDriverProbe+0x182) [0x80b82d2] 4: X (DoConfigure+0x1c8) [0x816b898] 5: X (InitOutput+0x1da) [0x80b98aa] 6: X (0x8048000+0x1ebbb) [0x8066bbb] 7: /lib/tls/i686/cmov/libc.so.6 (__libc_start_main+0xe6) [0x467bd6] 8: X (0x8048000+0x1e961) [0x8066961] Segmentation fault at address (nil) Caught signal 11 (Segmentation fault). Server aborting Please consult the The X.Org Foundation support at http://wiki.x.org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. ddxSigGiveUp: Closing log Note the line Can't load FireGL DRM library (libfglrxdrm.so) Note: I do have file /usr/lib/fglrx/xorg/modules/linux/libfglrxdrm.so It is strange that it segfaults whereas I can use Gnome with no problem but well... Might be related: I tried to install the driver from ATI's website recently, and from then glxgears crashes at start. How can I generate xorg.conf in those conditions? It might or might not involve solving the segfault problem.

  Read the article

• Data Structures usage and motivational aspects

  - by Aubergine

  For long student life I was always wondering why there are so many of them yet there seems to be lack of usage at all in many of them. The opinion didn't really change when I got a job. We have brilliant books on what they are and their complexities, but I never encounter resources which would actually give a good hint of practical usage. I perfectly understand that I have to look at problem , analyse required operations, look for data structure that does them efficiently. However in practice I never do that, not because of human laziness syndrome, but because when it comes to work I acknowledge time priority over self-development. Over time I thought that when I would be better developer I will automatically use more of them - that didn't happen at all or maybe I just didn't. Then I found that the colleagues usually in the same plate as me - knowing more or less some three of data structures and being totally happy about it and refusing to discuss this matter further with me, coming back to conversations about 'cool new languages' 'libraries that do jobs for you' and the joy to work under scrumban etc. I am stuck with ArrayLists, Arrays and SortedMap , which no matter what I do always suffice or either I tweak them to be capable of fulfilling my task. Yes, it might be inefficient but do we really have to care if Intel increases performance over years no matter if we improve our skills? Does new Xeon or IBM machines really care what we use? What if I like build things, but I am not particularly excited whether it is n log(n) or just n? Over twenty years the processing power increased enormously, which gives us freedom of not being critical about which one to use? On top of that new more optimized languages appear which support multiple cores more efficiently. To be more specific: I would like to find motivational material on complex real areas/cases of possible effective usages of data structures. I would be really grateful if you would provide relevant resources. There is similar question ,but in the end the links again mostly describe or do dumb example(vehicles, students or holy grail quest - yes, very relevant) them and people keep referring to the "scenario decides the data structure to use". I want to know these complex scenarios to be able to identify similarities to my scenario and then use them. The complex scenarios where it really matters and not necessarily of quantitive nature. It seems that data structures only concern is efficiency and nothing else? There seems to be no particular convenience for developer in use one over another. (only when I found scientific resources on why exactly simple carbohydrates are evil I stopped eating sugar and candies completely replacing it with less harmful fruits - I hope you can see the analogy)

  Read the article

• TechCast Live: "Java and Oracle, One Year Later" Replay Now Available

  - by Justin Kestelyn

  Earlier this week I had the opportunity to chat with Ajay Patel, Oracle's VP leading the Java Evangelist team, about "the state of the union" wrt Oracle and Java. Take a look: And here are some choice quotes, some paraphrased, as helpfully transcribed by Java evangelist Terrence Barr: "One key thing we have learned ... Java is not just a platform, it is also an ecosystem, and you can't have an ecosystem without a community." "The objectives, strategically [for Java at Oracle] have been pretty clear: How do we drive adoption, how do we build a larger, stronger developer community, how do we really make the platform much more competitive." "It's about transparency, involvement. IBM, RedHat, Apple have all agreed to working with us to make OpenJDK the best platform for open source development ... it is a sign that the community has been waiting to move the Java platform forward." "It's not just about Oracle anymore, it's about Java, the technology, the community, the developer base, and how we work with them to move the innovation forward." "Java is strategic to Oracle, and the community is strategic for Java to be successful ... it is critical to our business." On JavaFX 2.0: "... is coming to beta soon, with a release planned in second half [of 2011] ... will give you a new, high-performance graphics engine, the new API for JavaFX ... you will see a very strong, relevant platform for levering rich media platforms." On the JDK and SE: "... aggressively moving forward, JDK 7 is now code complete ... looking good for getting JDK 7 out by summer as we promised. Started work on JDK 8, Jigsaw and Lambda are moving along nicely, on track for JDK 8 release next year ... good progress." On Java EE and Glassfish: "... Very excited to have Glassfish 3.1 released, with clustering and management capabilities ... working with the JCP to shortly submit a number of JSRs for Java EE 7 ... You'll see Java EE 7 becoming the platform for cloud-based development." "You will see Oracle continue to step up to this role of Java steward, making sure that the language, the technology, the platform ... is competitive, relevant, and widely adopted." Making progress!

  Read the article

• Failed 12.04 installation

  - by Rob Sayer

  I tried installing Ubuntu 12.04 today. Not an upgrade, a new installation. It didn't work. My computer specs: Computer: Compaq presario CQ-104CA OS: Windows 7 Home 64 bit CPU: AMD V140 BIOS: latest Graphics: amd m880g with ati mobility radeon hd 4250 Wireless: atheros ar9285 Internal HD:SATA I wasn't connected to the internet at the time ... I know of a number of people who have installed ubuntu unconnected and just updated later. It seemed to go normally until I got to the part where I chose to install dual boot linux/windows. Then, the screen went black and the following test appeared (I left out the [OK]'s): checking battery state starting crash report submission daemon stating cpu interrupts balancing daemon stopping system V runlevel compatibility starting configure network device security stopping configure network device security stopping cold plug devices stopping log initial device creation starting enable remaining boot-time encrypting devices starting configure network device security starting save udev log and update rules stopping save udev log and update rules stopping enable remaining boot-time encrypted block devices checking for running unattended-upgrades acpid: exiting speech-dispatcher disabled: edit /etc/default/speech-disorder At this point, the CD is ejected. Then nothing. If I press the return key, it boots Windows. I don't think that's what's supposed to happen. Thinking the cd media or dvd drive may have been faulty, I downloaded the .iso again and made a bootable USB stick, as per your instructions. This time there was no cryptic crash screen. It just booted windows. I can't find any log files it may have left. Thinking the amd64 version may have been the wrong one, I tried downloading the x86 version. Same thing, both from cd and usb drive. Note I downloaded both files twice. I doubt it was a corrupted d/l. This is supposed to be a simple, transparent install. I went to the time and trouble of looking up my devices and drivers re ubuntu beforehand, and was prepared to do some configuration, though I know someone who has the same wireless device and his worked righted out of the box. But I spent over 3 hours trying to install it with only the above to show for it.

  Read the article

• SCVMM – Round 2 – How to create a Private Cloud using PowerShell

  - by Waclaw Chrabaszcz

  Originally posted on: http://geekswithblogs.net/Wchrabaszcz/archive/2013/06/28/scvmm--round-2--how-to-create-a-private.aspxHave you ever seen "A Bridge too far" movie? To not to wake up a click too far, it is good to script some tasks. Yes of course we can follow wizards, but some of us want to be warriorsJ. A small tip, take a look on credentials and system GUID examples. I don't know how about you, but for me it will be really useful in the future.    # credents$credential = Get-CredentialNew-SCRunAsAccount -Name "TESTDOMAIN\Administrator" -Credential $credential #storage $opsMgrServerCredential = Get-SCRunAsAccount -Name "TESTDOMAIN\Administrator"New-SCStorageClassification -Name "Bronze" -Description "" –RunAsynchronouslyNew-SCStorageClassification -Name "Silver" -Description "" –RunAsynchronouslyNew-SCStorageClassification -Name "Gold" -Description "" –RunAsynchronously # add a shared storageFind-SCComputer -ComputerName "dc.TESTDOMAIN.net"Add-SCStorageProvider -AddWindowsNativeWmiProvider -Name "dc.TESTDOMAIN.net" -RunAsAccount $opsMgrServerCredential -ComputerName "dc.TESTDOMAIN.net"$fileServer = Get-SCStorageFileServer "dc.TESTDOMAIN.net"$fileShares = @()$fileShares += Get-SCStorageFileShare -Name "VMMLibrary"Set-SCStorageFileServer -StorageFileServer $fileServer -AddStorageFileShareToManagement $fileShares –RunAsynchronously #fabric network$logicalNetwork = New-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network" -LogicalNetworkDefinitionIsolation $false -EnableNetworkVirtualization $true -UseGRE $true -IsPVLAN $false$allHostGroups = @()$allHostGroups += Get-SCVMHostGroup -Name "All Hosts"$allSubnetVlan = @()$allSubnetVlan += New-SCSubnetVLan -Subnet "10.0.0.0/24" -VLanID 0New-SCLogicalNetworkDefinition -Name "TESTDOMAIN-Service-Network_0" -LogicalNetwork $logicalNetwork -VMHostGroup $allHostGroups -SubnetVLan $allSubnetVlan #IP pool$logicalNetwork = Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network"$logicalNetworkDefinition = Get-SCLogicalNetworkDefinition -LogicalNetwork $logicalNetwork -Name "TESTDOMAIN-Service-Network_0" # Gateways$allGateways = @()$allGateways += New-SCDefaultGateway -IPAddress "10.0.0.1" –Automatic# DNS servers $allDnsServer = @("10.0.0.1")# DNS suffixes$allDnsSuffixes = @("TESTDOMAIN.net")# WINS servers$allWinsServers = @()New-SCStaticIPAddressPool -Name "TESTDOMAIN-Service-Network" -LogicalNetworkDefinition $logicalNetworkDefinition -Subnet "10.0.0.0/24" -IPAddressRangeStart "10.0.0.51" -IPAddressRangeEnd "10.0.0.75" -DefaultGateway $allGateways -DNSServer $allDnsServer -DNSSuffix "" -DNSSearchSuffix $allDnsSuffixes –RunAsynchronously #Hyper-V Virtual Networks$logicalNetwork = Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network" $vmNetwork = New-SCVMNetwork -Name "TESTDOMAIN-VMN" -LogicalNetwork $logicalNetwork -IsolationType "WindowsNetworkVirtualization" -CAIPAddressPoolType "IPV4" -PAIPAddressPoolType "IPV4"Write-Output $vmNetwork$subnet = New-SCSubnetVLan -Subnet "10.0.0.0/24"New-SCVMSubnet -Name "Con-SN" -VMNetwork $vmNetwork -SubnetVLan $subnet # bind VLAN with the Network Adapter$vmHost = Get-SCVMHost -ComputerName "VMM01.TESTDOMAIN.net"$vmHostNetworkAdapter = Get-SCVMHostNetworkAdapter -VMHost $vmHost #-Name "Intel 21140-Based PCI Fast Ethernet Adapter (Emulated)"Set-SCVMHostNetworkAdapter -VMHostNetworkAdapter $vmHostNetworkAdapter -Description "" -AvailableForPlacement $true -UsedForManagement $true $logicalNetwork = Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network" Set-SCVMHostNetworkAdapter -VMHostNetworkAdapter $vmHostNetworkAdapter -AddOrSetLogicalNetwork $logicalNetworkSet-SCVMHost -VMHost $vmHost -RunAsynchronously -NumaSpanningEnabled $true #Create a Private Cloud$Guid = [System.Guid]::NewGuid()Set-SCCloudCapacity -JobGroup $Guid -UseCustomQuotaCountMaximum $false -UseMemoryMBMaximum $false -UseCPUCountMaximum $false -UseStorageGBMaximum $false -UseVMCountMaximum $false -CustomQuotaCount 10 -MemoryMB 10240 -CPUCount 10 -StorageGB 386 -VMCount 10$resources = @()$resources += Get-SCLogicalNetwork -Name "TESTDOMAIN-Service-Network"$resources += Get-SCLoadBalancer -Manufacturer "Microsoft"$readonlyLibraryShares = @()$readonlyLibraryShares += Get-SCLibraryShare | where { $_.LibraryServer.Name -eq "dc.TESTDOMAIN.net" -and $_.Name -eq "VMMLibrary" }$addCapabilityProfiles = @()$addCapabilityProfiles += Get-SCCapabilityProfile -Name "Hyper-V"$Guid2 = [System.Guid]::NewGuid()Set-SCCloud -JobGroup $Guid2 -RunAsynchronously -AddCloudResource $resources -AddReadOnlyLibraryShare $readonlyLibraryShares -AddCapabilityProfile $addCapabilityProfiles$hostGroups = @()$hostGroups += Get-SCVMHostGroup -Name "TESTDOMAIN"New-SCCloud -VMHostGroup $hostGroups -Name "TESTDOMAIN-Cloud" -Description "" –RunAsynchronously

  Read the article

• Will HTML5 make Silverlight redundant?

  - by Laila

  One of the great features of Adobe AIR v2 that was launched this month was its support for some of the 2008 draft of HTML5. The HTML5 specification was started in 2004, but the full spec will probably not be approved by W3C until around 2022. One might have thought that it would take years yet from now to reach the point where any browsers were remotely HTML5-compliant, but enough of HTML5 is published and agreed to make a lot of it possible, and Safari and Adobe have got there thanks to Apple's open-source WebKit. The race for HTML 5 has been fuelled by the demand by Apple and Google for advanced graphics, typography, animations and transitions without having to rely on third party browser plug-ins such as Adobe Flash or Silverlight. There is good reason for this haste: Flash doesn't support touch-devices and has been slow in supporting hardware video decoders such as H.264. There is a strong requirement to do all that Flash can do in an open-standards way. Those with proprietary solutions remain sniffy. In AIR 2, Adobe pointedly disables the HTML5 and tags that allow basic playing of media content, saying that the specification is not final and there is still no standard for the supported formats, and adding that Safari implements a 'disjoint set' of codecs. Microsoft also has little interest in HTML 5 as it has so much invested in Silverlight. Google stands to gain by the Adobe AIR for Android as it will allow a lot of applications to be migrated easily to the platform, so sees Apple's war on Flash as a way of gaining market share. Why do we care? It is because HTML5/CSS3 provides facilities much far beyond HTML4, bring the reality of browser-based applications a lot closer. Probably most generally useful is the advanced typography: Safari and AIR already both support a way of reflowing text in a container across an arbitrary number of columns; Page-specific fonts can also be specified. Then there is 2D drawing, video, transitions, local storage, AJAX navigation and mutable DOM prototypes. HTML5 is likely to provide base functionality that is required but it is too early to be certain that it will render Flash, Silverlight or JavaFX obsolete. In the meantime, Adobe Air provides the best vehicle for developing HTML5/CSS3 applications without a twinge of worry about browser incompatibilities. Cheers, Laila

  Read the article

• How can I attach a model to the bone of another model?

  - by kaykayman

  I am trying to attach one animated model to one of the bones of another animated model in an XNA game. I've found a few questions/forum posts/articles online which explain how to attach a weapon model to the bone of another model (which is analogous to what I'm trying to achieve), but they don't seem to work for me. So as an example: I want to attach Model A to a specific bone in Model B. Question 1. As I understand it, I need to calculate the transforms which are applied to the bone on Model B and apply these same transforms to every bone in Model A. Is this right? Question 2. This is my code for calculating the Transforms on a specific bone. private Matrix GetTransformPaths(ModelBone bone) { Matrix result = Matrix.Identity; while (bone != null) { result = result * bone.Transform; bone = bone.Parent; } return result; } The maths of Matrices is almost entirely lost on me, but my understanding is that the above will work its way up the bone structure to the root bone and my end result will be the transform of the original bone relative to the model. Is this right? Question 3. Assuming that this is correct I then expect that I should either apply this to each bone in Model A, or in my Draw() method: private void DrawModel(SceneModel model, GameTime gametime) { foreach (var component in model.Components) { Matrix[] transforms = new Matrix[component.Model.Bones.Count]; component.Model.CopyAbsoluteBoneTransformsTo(transforms); Matrix parenttransform = Matrix.Identity; if (!string.IsNullOrEmpty(component.ParentBone)) parenttransform = GetTransformPaths(model.GetBone(component.ParentBone)); component.Player.Update(gametime.ElapsedGameTime, true, Matrix.Identity); Matrix[] bones = component.Player.GetSkinTransforms(); foreach (SkinnedEffect effect in mesh.Effects) { effect.SetBoneTransforms(bones); effect.EnableDefaultLighting(); effect.World = transforms[mesh.ParentBone.Index] * Matrix.CreateRotationY(MathHelper.ToRadians(model.Angle)) * Matrix.CreateTranslation(model.Position) * parenttransform; effect.View = getView(); effect.Projection = getProjection(); effect.Alpha = model.Opacity; } } mesh.Draw(); } I feel as though I have tried every conceivable way of incorporating the parenttransform value into the draw method. The above is my most recent attempt. Is what I'm trying to do correct? And if so, is there a reason it doesn't work? The above Draw method seems to transpose the models x/z position - but even at these wrong positions, they do not account for the animation of Model B at all. Note: As will be evident from the code my "model" is comprised of a list of "components". It is these "components" that correspond to a single "Microsoft.Xna.Framework.Graphics.Model"

  Read the article

• Ubuntu 13.04 boot into black screen, even after installing nvidia drivers, fail at: "Starting Reload cups, upon starting avahi-daemon..."

  - by Elad92

  I got a new machine with i7 4770k and gefore gtx660. I installed windows and then installed Ubuntu 13.04. In the installation everything went well, after the installation I again boot from the USB and choose try ubuntu, and installed boot-repair because windows automatically boot with no option for ubuntu. After I repaired the boot, I restarted and got into grub, when I chose Ubuntu I got message saying I'm running on low graphics mode and when I pressed ok the screen turned off. I couldn't do anything so I restarted and after reading this post: My computer boots to a black screen, what options do I have to fix it? I got into recovery, selected dpkg and repaired packages. Then I rebooted, and tried to press 'e' and change quiet splash to no splash and nomodeset but unfortunately both of them didn't work, and not the screen didn't get turned off, but I just saw a blank screen. So I rebooted again, entered the recovery, and this time I went to the root shell, and tried to install nvidia drivers from this guide here: http://www.howopensource.com/2012/10/install-nvidia-geforce-driver-in-ubuntu-12-10-12-04-using-ppa/ I rebooted and got the same black screen again (the screen didn't go off, just saw a blank screen). In the grub I see that the kernel is 3.8.0-25. I also checked that the usb files are not corrupted using the check CD from the ubuntu installation screen. I'm really frustrated, I don't know what else can I do. (If someone also knows how can I connect to wifi using the root shell it will be very appreciated, because when I choose the 'enable networking' it again booting me to a black screen. Thanks Edit After digging more, I again boot with nomodeset and saw where is it failing, this is the lines I saw: * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated [OK] * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated [fail] I searched for it in google and this is the closest result I got: http://ubuntuforums.org/showthread.php?t=2144261 i didn't find any way to solve it in the internet, from what I understand this is a problem with 13.04. If someone knows how to fix it I will be very grateful. Thanks Edit 2 - 23.6.13 As Mitch suggested, I disabled the avahi-daemon, and when I boot in nomodeset I get the following error: What else can be the problem?

  Read the article

• Why is my system freezing when I switch users

  - by ZeroDivide

  Hello I've recently upgraded from 13.04 to 13.10 64bit. I'm running AMD graphics with the proprietary drivers. I have two user accounts. Mine(administrator) and my girlfriend's(standard) My girlfriend clicks "switch user" from my lock screen and logs in fine. I then try to click "switch user" from her lock screen and everything goes black. Then the monitor blinks on and off with just a single cursor. I have no way to access the terminal, the system is unresponsive and I have to hit the power button. Even ctrl + alt + f4 or ctrl + alt + t doesn't get me a terminal. When I press the power button on my system, it does start printing out the shutdown sequence on the monitor. Here is my .xsession-errors Script for ibus started at run_im. Script for auto started at run_im. Script for default started at run_im. Here is hers: init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd main process ended, respawning init: at-spi2-registryd respawning too fast, stopped init: logrotate main process (4726) killed by TERM signal init: upstart-dbus-session-bridge main process (4865) terminated with status 1 init: gnome-settings-daemon main process (4843) terminated with status 1 init: gnome-session main process (4852) terminated with status 1 init: unity-panel-service main process (4863) killed by KILL signal I found some advice in a forum to look for at-spi2-registryd in my system logs. Perhaps it will be useful. executing this: sudo grep -r at-spi2-registryd /var/log/* produces this: /var/log/lightdm/x-1-greeter.log:** (at-spi2-registryd:4384): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-1-greeter.log:** (at-spi2-registryd:4384): WARNING **: Unable to register client with session manager /var/log/lightdm/x-2-greeter.log.old:** (at-spi2-registryd:7447): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-2-greeter.log.old:** (at-spi2-registryd:7447): WARNING **: Unable to register client with session manager /var/log/lightdm/x-0-greeter.log:** (at-spi2-registryd:1378): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-0-greeter.log:** (at-spi2-registryd:1378): WARNING **: Unable to register client with session manager /var/log/lightdm/x-0-greeter.log.old:** (at-spi2-registryd:1357): WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.gnome.SessionManager was not provided by any .service files /var/log/lightdm/x-0-greeter.log.old:** (at-spi2-registryd:1357): WARNING **: Unable to register client with session manager Any ideas what is going on?

  Read the article

• HDMI sound gone, can't figure out how to turn it back on

  - by Oli

  I have had an Acer Revo box as a media centre for a while. I recently installed Ubuntu Server (10.10) on it and polished it up with nodm (one of the most simple ways to launch an X session) and installed boxee. It's been working fine for over a month. It's just running ALSA. I've had problems with PulseAudio/Boxee/HDMI before so I wanted to keep it simple. And that worked. It pushed both PCM and digital (AAC and various Dolby codecs) over HDMI perfectly. But I restarted it the other day after mucking around with some nfs configuration and now there isn't any sound. The hardware is an ION chipset. Nvidia 9400M graphics with Nvidia MCP79/7A audio. One thing I have noticed is there doesn't appear to be any sign of a IEC958 device. A traditional fix in the past for fresh installs has been to load alsamixer, find the IEC device and toggle its mute but I can't. I'm certain this used to represent the HDMI output. It just doesn't seem to exist any more unless I run sudo alsa-utils restart while boxee is running, when I see it in an error message: * Shutting down ALSA... [ OK ] * Setting up ALSA... * warning: 'alsactl restore' failed with error message 'alsactl: set_control:1388: Cannot write control '2:0:0:IEC958 Playback Default:0' : Operation not permitted'... ...done. When nodm (and thus boxee) aren't running, I don't see this error but alsamixer still doesn't show the IEC channel. aplay -l gives: card 0: NVidia [HDA NVidia], device 0: ALC662 rev1 Analog [ALC662 rev1 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 0/1 Subdevice #0: subdevice #0 Its section in lshw reads: *-multimedia description: Audio device product: MCP79 High Definition Audio vendor: nVidia Corporation physical id: 8 bus info: pci@0000:00:08.0 version: b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list configuration: driver=HDA Intel latency=0 maxlatency=5 mingnt=2 resources: irq:22 memory:fae78000-fae7bfff I was running on the stock PAE kernel but now it's running on 2.6.37.1. I upgraded to see if that fixed things; it didn't. I'm considering a reinstall but I hate doing that because a) there's a bit of custom configuration in getting X and Boxee to start on boot and b) I don't know what the problem is. If I reinstall this time, I'll end up doing that every time the sound breaks. I love Ubuntu but I don't want to install it once a month. Is there any way to forcibly reset all alsa settings and restart from scratch (without doing a reinstall)? Any other tips? If you need more information, just ask.

  Read the article

• Running C++ AMP kernels on the CPU

  - by Daniel Moth

  One of the FAQs we receive is whether C++ AMP can be used to target the CPU. For targeting multi-core we have a technology we released with VS2010 called PPL, which has had enhancements for VS 11 – that is what you should be using! FYI, it also has a Linux implementation via Intel's TBB which conforms to the same interface. When you choose to use C++ AMP, you choose to take advantage of massively parallel hardware, through accelerators like the GPU. Having said that, you can always use the accelerator class to check if you are running on a system where the is no hardware with a DirectX 11 driver, and decide what alternative code path you wish to follow.  In fact, if you do nothing in code, if the runtime does not find DX11 hardware to run your code on, it will choose the WARP accelerator which will run your code on the CPU, taking advantage of multi-core and SSE2 (depending on the CPU capabilities WARP also uses SSE3 and SSE 4.1 – it does not currently use AVX and on such systems you hopefully have a DX 11 GPU anyway). A few things to know about WARP It is our fallback CPU solution, not intended as a primary target of C++ AMP. WARP stands for Windows Advanced Rasterization Platform and you can read old info on this MSDN page on WARP. What is new in Windows 8 Developer Preview is that WARP now supports DirectCompute, which is what C++ AMP builds on. It is not currently clear if we will have a CPU fallback solution for non-Windows 8 platforms when we ship. When you create a WARP accelerator, its is_emulated property returns true. WARP does not currently support double precision.   BTW, when we refer to WARP, we refer to this accelerator described above. If we use lower case "warp", that refers to a bunch of threads that run concurrently in lock step and share the same instruction. In the VS 11 Developer Preview, the size of warp in our Ref emulator is 4 – Ref is another emulator that runs on the CPU, but it is extremely slow not intended for production, just for debugging. Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

< Previous Page | 294 295 296 297 298 299 300 301 302 303 304 305  | Next Page >