Search Results

Search found 8414 results on 337 pages for 'critical section'.

Page 299/337 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >

• Computer Networks UNISA - Chap 8 &ndash; Wireless Networking

  - by MarkPearl

  After reading this section you should be able to Explain how nodes exchange wireless signals Identify potential obstacles to successful transmission and their repercussions, such as interference and reflection Understand WLAN architecture Specify the characteristics of popular WLAN transmission methods including 802.11 a/b/g/n Install and configure wireless access points and their clients Describe wireless MAN and WAN technologies, including 802.16 and satellite communications The Wireless Spectrum All wireless signals are carried through the air by electromagnetic waves. The wireless spectrum is a continuum of the electromagnetic waves used for data and voice communication. The wireless spectrum falls between 9KHZ and 300 GHZ. Characteristics of Wireless Transmission Antennas Each type of wireless service requires an antenna specifically designed for that service. The service’s specification determine the antenna’s power output, frequency, and radiation pattern. A directional antenna issues wireless signals along a single direction. An omnidirectional antenna issues and receives wireless signals with equal strength and clarity in all directions The geographical area that an antenna or wireless system can reach is known as its range Signal Propagation LOS (line of sight) uses the least amount of energy and results in the reception of the clearest possible signal. When there is an obstacle in the way, the signal may… pass through the object or be obsrobed by the object or may be subject to reflection, diffraction or scattering. Reflection – waves encounter an object and bounces off it. Diffraction – signal splits into secondary waves when it encounters an obstruction Scattering – is the diffusion or the reflection in multiple different directions of a signal Signal Degradation Fading occurs as a signal hits various objects. Because of fading, the strength of the signal that reaches the receiver is lower than the transmitted signal strength. The further a signal moves from its source, the weaker it gets (this is called attenuation) Signals are also affected by noise – the electromagnetic interference) Interference can distort and weaken a wireless signal in the same way that noise distorts and weakens a wired signal. Frequency Ranges Older wireless devices used the 2.4 GHZ band to send and receive signals. This had 11 communication channels that are unlicensed. Newer wireless devices can also use the 5 GHZ band which has 24 unlicensed bands Narrowband, Broadband, and Spread Spectrum Signals Narrowband – a transmitter concentrates the signal energy at a single frequency or in a very small range of frequencies Broadband – uses a relatively wide band of the wireless spectrum and offers higher throughputs than narrowband technologies The use of multiple frequencies to transmit a signal is known as spread-spectrum technology. In other words a signal never stays continuously within one frequency range during its transmission. One specific implementation of spread spectrum is FHSS (frequency hoping spread spectrum). Another type is known as DSS (direct sequence spread spectrum) Fixed vs. Mobile Each type of wireless communication falls into one of two categories Fixed – the location of the transmitted and receiver do not move (results in energy saved because weaker signal strength is possible with directional antennas) Mobile – the location can change WLAN (Wireless LAN) Architecture There are two main types of arrangements Adhoc – data is sent directly between devices – good for small local devices Infrastructure mode – a wireless access point is placed centrally, that all devices connect with 802.11 WLANs The most popular wireless standards used on contemporary LANs are those developed by IEEE’s 802.11 committee. Over the years several distinct standards related to wireless networking have been released. Four of the best known standards are also referred to as Wi-Fi. They are…. 802.11b 802.11a 802.11g 802.11n These four standards share many characteristics. i.e. All 4 use half duplex signalling Follow the same access method Access Method 802.11 standards specify the use of CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) to access a shared medium. Using CSMA/CA before a station begins to send data on an 802.11 network, it checks for existing wireless transmissions. If the source node detects no transmission activity on the network, it waits a brief period of time and then sends its transmission. If the source does detect activity, it waits a brief period of time before checking again. The destination node receives the transmission and, after verifying its accuracy, issues an acknowledgement (ACT) packet to the source. If the source receives the ACK it assumes the transmission was successful, – if it does not receive an ACK it assumes the transmission failed and sends it again. Association Two types of scanning… Active – station transmits a special frame, known as a prove, on all available channels within its frequency range. When an access point finds the probe frame, it issues a probe response. Passive – wireless station listens on all channels within its frequency range for a special signal, known as a beacon frame, issued from an access point – the beacon frame contains information necessary to connect to the point. Re-association occurs when a mobile user moves out of one access point’s range and into the range of another. Frames Read page 378 – 381 about frames and specific 802.11 protocols Bluetooth Networks Sony Ericson originally invented the Bluetooth technology in the early 1990s. In 1998 other manufacturers joined Ericsson in the Special Interest Group (SIG) whose aim was to refine and standardize the technology. Bluetooth was designed to be used on small networks composed of personal communications devices. It has become popular wireless technology for communicating among cellular telephones, phone headsets, etc. Wireless WANs and Internet Access Refer to pages 396 – 402 of the textbook for details.

  Read the article

• Creating SparseImages for Pivot

  - by John Conwell

  Learning how to programmatically make collections for Microsoft Live Labs Pivot has been a pretty interesting ride. There are very few examples out there, and the folks at MS Live Labs are often slow on any feedback.  But that is what Reflector is for, right? Well, I was creating these InfoCard images (similar to the Car images in the "New Cars" sample collection that that MS created for Pivot), and wanted to put a Tag Cloud into the info card.  The problem was the size of the tag cloud might vary in order for all the tags to fit into the tag cloud (often times being bigger than the info card itself).  This was because the varying word lengths and calculated font sizes. So, to fix this, I made the tag cloud its own separate image from the info card.  Then, I would create a sparse image out of the two images, where the tag cloud fit into a small section of the info card.  This would allow the user to see the info card, but then zoom into the tag cloud and see all the tags at a normal resolution.  Kind'a cool. But...I couldn't find one code example (not one!) of how to create a sparse image.  There is one page on the SeaDragon site (http://www.seadragon.com/developer/creating-content/deep-zoom-tools/) that gives over the API for creating images and collections, and it sparsely goes over how to create a sparse image, but unless you are familiar with the API already, the documentation doesn't help very much. The key is the Image.ViewportWidth and Image.ViewportOrigin properties of the image that is getting super imposed on the main image.  I'll walk through the code below.  I've setup a couple Point structs to represent the parent and sub image sizes, as well as where on the parent I want to position the sub image.  Next, create the parent image.  This is pretty straight forward.  Then I create the sub image.  Then I calculate several ratios; the height to width ratio of the sub image, the width ratio of the sub image to the parent image, the height ratio of the sub image to the parent image, then the X and Y coordinates on the parent image where I want the sub image to be placed represented as a ratio of the position to the parent image size. After all these ratios have been calculated, I use them to calculate the Image.ViewportWidth and Image.ViewportOrigin values, then pass the image objects into the SparseImageCreator and call Create. The key thing that was really missing from the API documentation page is that when setting up your sub images, everything is expressed in a ratio in relation to the main parent image.  If I had known this, it would have saved me a lot of trial and error time.  And how did I figure this out?  Reflector of course!  There is a tool called Deep Zoom Composer that came from MS Live Labs which can create a sparse image.  I just dug around the tool's code until I found the method that create sparse images.  But seriously...look at the API documentation from the SeaDragon size and look at the code below and tell me if the documentation would have helped you at all.  I don't think so!   public static void WriteDeepZoomSparseImage(string mainImagePath, string subImagePath, string destination) {     Point parentImageSize = new Point(720, 420);     Point subImageSize = new Point(490, 310);     Point subImageLocation = new Point(196, 17);     List<Image> images = new List<Image>();     //create main image     Image mainImage = new Image(mainImagePath);     mainImage.Size = parentImageSize;     images.Add(mainImage);     //create sub image     Image subImage = new Image(subImagePath);     double hwRatio = subImageSize.X/subImageSize.Y;            // height width ratio of the tag cloud     double nodeWidth = subImageSize.X/parentImageSize.X;        // sub image width to parent image width ratio     double nodeHeight = subImageSize.Y / parentImageSize.Y;    // sub image height to parent image height ratio     double nodeX = subImageLocation.X/parentImageSize.X;       //x cordinate position on parent / width of parent     double nodeY = subImageLocation.Y / parentImageSize.Y;     //y cordinate position on parent / height of parent     subImage.ViewportWidth = (nodeWidth < double.Epsilon) ? 1.0 : (1.0 / nodeWidth);     subImage.ViewportOrigin = new Point(         (nodeWidth < double.Epsilon) ? -1.0 : (-nodeX / nodeWidth),         (nodeHeight < double.Epsilon) ? -1.0 : ((-nodeY / nodeHeight) / hwRatio));     images.Add(subImage);     //create sparse image     SparseImageCreator creator = new SparseImageCreator();     creator.Create(images, destination); }

  Read the article

• Add SQL Azure database to Azure Web Role and persist data with entity framework code first.

  - by MagnusKarlsson

  In my last post I went for a warts n all approach to set up a web role on Azure. In this post I’ll describe how to add an SQL Azure database to the project. This will be described with an as minimal as possible amount of code and screen dumps. All questions are welcome in the comments area. Please don’t email since questions answered in the comments field is made available to other visitors. As an example we will add a comments section to the site we used in the previous post (Länk här). Steps: 1. Create a Comments entity and then use Scaffolding to set up controller and view, and add ConnectionString to web.config. 2. Create SQL Azure database in Management Portal and link the new database 3. Test it online!   1. Right click Models folder, choose add, choose “class…” . Name the Class Comment. 1.1 Replace the Code in the class with the following: using System.Data.Entity; namespace MvcWebRole1.Models { public class Comment {    public int CommentId { get; set; }    public string Name { get; set; }      public string Content { get; set; } } public class CommentsDb : DbContext { public DbSet<Comment> CommentEntries { get; set; } } } Now Entity Framework can create a database and a table named Comment. Build your project to assert there are no build errors.   1.2 Right click Controllers folder, choose add, choose “class…” . Name the Class CommentController and fill out the values as in the example below.     1.3 Click Add. Visual Studio now creates default View for CRUD operations and a Controller adhering to these and opens them. 1.3 Open Web.config and add the following connectionstring in <connectionStrings> node. <add name="CommentsDb” connectionString="data source=(LocalDB)\v11.0;Integrated Security=SSPI;AttachDbFileName=|DataDirectory|\CommentsDb.mdf;Initial Catalog=CommentsDb;MultipleActiveResultSets=True" providerName="System.Data.SqlClient" />   1.4 Save All and press F5 to start the application. 1.5 Go to http://127.0.0.1:81/Comments which will redirect you through CommentsController to the Index View which looks like this:     Click Create new. In the Create-view, add name and content and press Create.   1: // 2: // POST: /Comments/Create 3:  4: [HttpPost] 5: public ActionResult Create(Comment comment) 6: { 7: if (ModelState.IsValid) 8: { 9: db.CommentEntries.Add(comment); 10: db.SaveChanges(); 11: return RedirectToAction("Index"); 12: } 13:  14: return View(comment); 15: } 16:    The default View() is Index so that is the View you will come to. Looking like this: 1: // 2: // GET: /Comments/ 3: 4: public ActionResult Index() 5: { 6: return View(db.CommentEntries.ToList()); 7: } Resulting in the following screen dump(success!):   2. Now, go to the Management portal and Create a new db.   2.1 With the new database created. Click the DB icon in the left most menu. Then click the newly created database. Click DASHBOARD in the top menu. Finally click Connections strings in the right menu to get the connection string we need to add in our web.debug.config file.   2.2 Now, take a copy of the connection String earlier added to the web.config and paste in web.debug.conifg in the connectionstrings node. Replace everything within “ “ in the copied connectionstring with that you got from SQL Azure. You will have something like this:   2.3 Rebuild the application, right click the cloud project and choose “Package…” (if you haven’t set up publishing profile which we will do in our next blog post). Remember to choose the right config file, use debug for staging and release for production so your databases won’t collide. You should see something like this:   2.4 Go to Management Portal and click the Web Services menu, choose your service and click update in the bottom menu.   2.5 Link the newly created database to your application. Click the LINKED RESOURCES in the top menu and then click “Link” in the bottom menu. You should get something like this. 3. Alright then. Under the Dashboard you can find the link to your application. Click it to open it in a browser and then go to ~/Comments to try it out just the way we did locally. Success and end of this story!

  Read the article

• To SYNC or not to SYNC – Part 3

  - by AshishRay

  I can't believe it has been almost a year since my last blog post. I know, that's an absolute no-no in the blogosphere. And I know that "I have been busy" is not a good excuse. So - without trying to come up with an excuse - let me state this - my apologies for taking such a long time to write the next Part. Without further ado, here goes. This is Part 3 of a multi-part blog article where we are discussing various aspects of setting up Data Guard synchronous redo transport (SYNC). In Part 1 of this article, I debunked the myth that Data Guard SYNC is similar to a two-phase commit operation. In Part 2, I discussed the various ways that network latency may or may not impact a Data Guard SYNC configuration. In this article, I will talk in details regarding why Data Guard SYNC is a good thing. I will also talk about distance implications for setting up such a configuration. So, Why Good? Why is Data Guard SYNC a good thing? Because, at the end of the day, this gives you the assurance of zero data loss - it doesn’t matter what outage may befall your primary system. Befall! Boy, that sounds theatrical. But seriously - think about this - it minimizes your data risks. That’s a big deal. Whether you have an outage due to bad disks, faulty hardware components, hardware / software bugs, physical data corruptions, power failures, lightning that takes out significant part of your data center, fire that melts your assets, water leakage from the cooling system, human errors such as accidental deletion of online redo log files - it doesn’t matter - you can have that “Om - peace” look on your face and then you can failover to the standby system, without losing a single bit of data in your Oracle database. You will be a hero, as shown in this not so imaginary conversation: IT Manager: Well, what’s the status? You: John is doing the trace analysis on the storage array. IT Manager: So? How long is that gonna take? You: Well, he is stuck, waiting for a response from <insert your not-so-favorite storage vendor here>. IT Manager: So, no root cause yet? You: I told you, he is stuck. We have escalated with their Support, but you know how long these things take. IT Manager: Darn it - the site is down! You: Not really … IT Manager: What do you mean? You: John is stuck, but Sreeni has already done a failover to the Data Guard standby. IT Manager: Whoa, whoa - wait! Failover means we lost some data, why did you do this without letting the Business group know? You: We didn’t lose any data. Remember, we had set up Data Guard with SYNC? So now, any problems on the production – we just failover. No data loss, and we are up and running in minutes. The Business guys don’t need to know. IT Manager: Wow! Are we great or what!! You: I guess … Ok, so you get it - SYNC is good. But as my dear friend Larry Carpenter says, “TANSTAAFL”, or "There ain't no such thing as a free lunch". Yes, of course - investing in Data Guard SYNC means that you have to invest in a low-latency network, you have to monitor your applications and database especially in peak load conditions, and you cannot under-provision your standby systems. But all these are good and necessary things, if you are supporting mission-critical apps that are supposed to be running 24x7. The peace of mind that this investment will give you is priceless, especially if you are serious about HA. How Far Can We Go? Someone may say at this point - well, I can’t use Data Guard SYNC over my coast-to-coast deployment. Most likely - true. So how far can you go? Well, we have customers who have deployed Data Guard SYNC over 300+ miles! Does this mean that you can also deploy over similar distances? Duh - no! I am going to say something here that most IT managers don’t like to hear - “It depends!” It depends on your application design, application response time / throughput requirements, network topology, etc. However, because of the optimal way we do SYNC, customers have been able to stretch Data Guard SYNC deployments over longer distances compared to traditional, storage-centric ways of doing this. The MAA Database 10.2 best practices paper Data Guard Redo Transport & Network Configuration, and Oracle Database 11.2 High Availability Best Practices Manual talk about some of these SYNC-related metrics. For example, a test deployment of Data Guard SYNC over 330 miles with 10ms latency showed an impact less than 5% for a busy OLTP application. Even if you can’t deploy Data Guard SYNC over your WAN distance, or if you already have an ASYNC standby located 1000-s of miles away, here’s another nifty way to boost your HA. Have a local standby, configured SYNC. How local is “local”? Again - it depends. One customer runs a local SYNC standby across the campus. Another customer runs it across 15 miles in another data center. Both of these customers are running Data Guard SYNC as their HA standard. If a localized outage affects their primary system, no problem! They have all the data available on the standby, to which they can failover. Very fast. In seconds. Wait - did I say “seconds”? Yes, Virginia, there is a Santa Claus. But you have to wait till the next blog article to find out more. I assure you tho’ that this time you won’t have to wait for another year for this.

  Read the article

• Alcatel-Lucent: Enterprise 2.0: The Top 5 Things I would Do Over

  - by Kellsey Ruppel

  Happy Monday! Does anyone else feel as if the weekend went entirely too quickly? At least for those of us in the United States, we have the 4th of July Holiday next week to look forward to This week on the blog, we are going to focus on "WebCenter by Example" and highlight best practices from customers and partners. I recently came across this article and I think this is a great example of how we can learn from one another when it comes to social collaboration adoption. Do you agree with Jem? What things or best practices have you learned in your organizations?  By Jem Janik, Enterprise community manager, Alcatel-Lucent  Not so long ago, Engage, the Alcatel-Lucent employee social network and collaboration platform, celebrated its third birthday. With more than 25,000 members actively interacting each month, Engage has been a big enough success that it’s been the subject of external articles, and often those of us who helped launch it will go out and speak about what aspects contributed to that success. Hindsight is still 20/20 and what it takes to successfully launch an enterprise 2.0 community is fairly well-known now.  Today I want to tell you what I suspect you really want to know about.  As the enterprise community manager for Engage, after three years in, what are the top 5 things I wish we (and I mostly mean me) could do over? #5 Define your analytics solution from the start There is so much to do when you launch a community and initially growing it without complete chaos is quite a task.  It doesn’t take too long to get to a point where you want to focus your continued efforts in growing company collaboration.  Do people truly talk across regional boundaries or have we shifted siloed conversations to a new platform.  Is there one organization that doesn’t interact with another? If you are lucky you’ll have someone in your community team well versed in the world of databases and SQL queries, but it takes time to figure out what backend analytics data actually means. Professional support can be expensive and it may be hard to justify later as it typically has the community manager as the only main customer.  Figure out what you think you’ll want to know and how to get it early on. The sooner the better even if it doesn’t seem that critical at the time. #4 Lobbies guide you to the right places One piece of feedback that comes up more and more as we keep growing Engage is it’s hard to find stuff, or new people are not sure where to start. Something we’re doing now is defining some general topic areas of interest to be like “lobbies” into the platform and some common hashtags to go with them. I liken this to walking into a large medical or professional building for the first time.  There are hundreds of offices, and you look to a sign in the lobby to get guided to the right place for you.  We’re building that sign for members now, but again we missed the boat as the majority of the company has had their initial Engage experience. #3 Clean up, clean up, clean up Knowledge work and folksonomies are messy! The day we opened the doors to Engage I would have said we should keep everything ever created in Engage with an argument that it was a window into our collective knowledge so nothing should go.  Well, 6000+ groups and 200,000+ pieces of content later, I’ve changed my mind.  As previously mentioned, with too much “stuff” the system can be overwhelming to new members and it makes it harder to get what you’re looking for.   Do we need that help document about a tool we no longer have? NO!  Do we need that group that had 1 document and 2 discussions in the last two years? NO! Should we only have one group about a given topic instead of 4?  YES! Last fall, Engage defined a cleanup process for groups not used for a long time.  We also formed a volunteer cleaning army who are extra eyes on the hunt for “stuff” that should be updated, merged, or deleted.  It’s better late than never, but in line with what’s becoming a theme I wish these efforts had started earlier. #2 Communications & local community management One of the most important aspects of my job is to make sure people who should be talking to each other are actually doing it.  Connecting people to the other people they should know, the groups they should join, a piece of content that shouldn’t be missed.   I have worked both inside and outside of communications teams, and they are the best informed people in your company.  They know when something big is coming, how it impacts employees, how it fits with strategy, who else knows more, etc.  Having communications professionals who are power users can help scale up community management because they are already so well connected.  They also need to have the platform skills to pay attention without suffering email overload, how to grab someone’s attention, etc.  I wish I’d had figured this out much earlier.  If I had I would have groomed more communications colleagues into advocates and power members right at the start. #1 Grooming advocates vs. natural advocates I’ve just alluded to this above already. The very best advocates are those who naturally embrace your platform and automatically start to see new ways to work within it.  Those advocates seem to come out of the woodwork naturally since some of them are early adopters.  Not surprisingly, our best advocates today are those same people who were willing to come kick the tires when the community was completely empty.  Unfortunately, we didn’t get a global spread of those natural advocates.  I did ask around when we first launched for other people who might be good candidates, but didn’t push too hard as there were so many other things to get ready.  That was a mistake.  If I could get a redo I would have formally asked for people to be assigned where there were gaps and groomed them into an advocate.  Today as we find new advocates to fill the gaps, people are hesitant as the initial set has three years of practice are ahead of the curve power members; it definitely would have been easier earlier on. As fairly early adopters to corporate scale enterprise collaboration, there hasn’t been a roadmap to follow as we’ve grown Engage, which is part of the fun! It’s clear a lot of issues are more easily tackled the earlier you identify and begin to correct them, and I’ve identified the main five I wish I could redo.  In the spirit of collaboration, I hope someone else learns from my mistakes! View the original article by Jem here. 

  Read the article

• Part 8: How to name EBS Customizations

  - by volker.eckardt(at)oracle.com

  You might wonder why I am discussing this here. The reason is simple: nearly every project has a bit different naming conventions, which makes a the life always a bit complicated (for developers, but also setup responsible, and also for consultants).  Although we always create a document to describe the technical object naming conventions, I have rarely seen a dedicated document  with functional naming conventions. To be precisely, from my stand point, there should always be one global naming definition for an implementation! Let me discuss some related questions: What is the best convention for the customization reference? How to name database objects (tables, packages etc.)? How to name functional objects like Value Sets, Concurrent Programs, etc. How to separate customizations from standard objects best? What is the best convention for the customization reference? The customization reference is the key you use to reference your customization from other lists, from the project plan etc. Usually it is something like XXHU_CONV_22 (HU=customer abbreviation, CONV=Conversion object #22) or XXFA_DEPRN_RPT_02 (FA=Fixed Assets, DEPRN=Short object group, here depreciation, RPT=Report, 02=2nd report in this area) As this is just a reference (not an object name yet), I would prefer the second option. XX=Customization, FA=Main EBS Module linked (you may have sometimes more, but FA is the main) DEPRN_RPT=Short name to specify the customization 02=a unique number Important here is that the HU isn’t used, because XX is enough to mark a custom object, and the 3rd+4th char can be used by the EBS module short name. How to name database objects (tables, packages etc.)? I was leading different developer teams, and I know that one common way is it to take the Customization reference and add more chars behind to classify the object (like _V for view and _T1 for triggers etc.). The only concern I have with this approach is the reusability. If you name your view XXFA_DEPRN_RPT_02_V, no one will by choice reuse this nice view, as it seams to be specific for this CEMLI. My suggestion is rather to name the view XXFA_DEPRN_PERIODS_V and allow herewith reusability for other CEMLIs (although the view will be deployed primarily with CEMLI package XXFA_DEPRN_RPT_02). (check also one of the following Blogs where I will talk about deployment.) How to name Value Sets, Concurrent Programs, etc. For Value Sets I would go with the same convention as for database objects, starting with XX<Module> …. For Concurrent Programs the situation is a bit different. This “object” is seen and used by a lot of users, and they will search for. In many projects it is common to start again with the company short name, or with XX. My proposal would differ. If you have created your own report and you name it “XX: Invoice Report”, the user has to remember that this report does not start with “I”, it starts with X. Would you like typing an X if you are looking for an Invoice report? No, you wouldn’t! So my advise would be to name it:   “Invoice Report (XXAP)”. Still we know it is custom (because of the XXAP), but the end user will type the key “i” to get it (and will see similar reports starting also with “i”). I hope that the general schema behind has now become obvious. How to separate customizations from standard objects best? I would not have this section here if the naming would not play an important role. Unfortunately, we can not always link a custom application to our own object, therefore the naming is really important. In the file system structure we use our $XXyy_TOP, in JAVA_TOP it is perhaps also “xx” in front. But in the database itself? Although there are different concepts in place, still many implementations are using the standard “apps” approach, means custom objects are stored in the apps schema (which should not cause any trouble). Final advise: review the naming conventions regularly, once a month. You may have to add more! And, publish them! To summarize: Technical and functional customized objects should always follow a naming convention. This naming convention should be project wide, and only one place shall be used to maintain (like in a Wiki). If the name is for the end user, rather put a customization identifier at the end; if it is an internal name, start with XX…

  Read the article

• PanelGridLayout - A Layout Revolution

  - by Duncan Mills

  With the most recent 11.1.2 patchset (11.1.2.3) there has been a lot of excitement around ADF Essentials (and rightly so), however, in all the fuss I didn't want an even more significant change to get missed - yes you read that correctly, a more significant change! I'm talking about the new panelGridLayout component, I can confidently say that this one of the most revolutionary components that we've introduced in 11g, even though it sounds rather boring. To be totally accurate, panelGrid was introduced in 11.1.2.2 but without any presence in the component palette or other design time support, so it was largely missed unless you read the release notes. However in this latest patchset it's finally front and center. Its time to explore - we (really) need to talk about layout.  Let's face it,with ADF Faces rich client, layout is a rather arcane pursuit, once you are a layout master, all bow before you, but it's more of an art than a science, and it is often, in fact, way too difficult to achieve what should (apparently) be a pretty simple. Here's a great example, it's a homework assignment I set for folks I'm teaching this stuff to:  The requirements for this layout are: The header is 80px high, the footer is 30px. These are both fixed.  The first section of the header containing the logo is 180px wide The logo is centered within the top left hand corner of the header  The title text is start aligned in the center zone of the header and will wrap if the browser window is narrowed. It should be aligned in the center of the vertical space  The about link is anchored to the right hand side of the browser with a 20px gap and again is center aligned vertically. It will move as the browser window is reduced in width. The footer has a right aligned copyright statement, again middle aligned within a 30px high footer region and with a 20px buffer to the right hand edge. It will move as the browser window is reduced in width. All remaining space is given to a central zone, which, in this case contains a panelSplitter. Expect that at some point in time you'll need a separate messages line in the center of the footer.  In the homework assigment I set I also stipulate that no inlineStyles can be used to control alignment or margins and no use of other taglibs (e.g. JSF HTML or Trinidad HTML). So, if we take this purist approach, that basic page layout (in my stock solution) requires 3 panelStretchLayouts, 5 panelGroupLayouts and 4 spacers - not including the spacer I use for the logo and the contents of the central zone splitter - phew! The point is that even a seemingly simple layout needs a bit of thinking about, particulatly when you consider strechting and browser re-size behavior. In fact, this little sample actually teaches you much of what you need to know to become vaguely competant at layouts in the framework. The underlying result of "the way things are" is that most of us reach for panelStretchLayout before even finishing the first sip of coffee as we embark on a new page design. In fact most pages you will see in any moderately complex ADF page will basically be nested panelStretchLayouts and panelGroupLayouts, sometimes many, many levels deep. So this is a problem, we've known this for some time and now we have a good solution. (I should point out that the oft-used Trinidad trh tags are not a particularly good solution as you're tie-ing yourself to an HTML table based layout in that case with a host of attendent issues in resize and bi-di behavior, but I digress.) So, tadaaa, I give to you panelGridLayout. PanelGrid, as the name suggests takes a grid like (dare I say slightly gridbag-like) approach to layout, dividing your layout into rows and colums with margins, sizing, stretch behaviour, colspans and rowspans all rolled in, all without the use of inlineStyle. As such, it provides for a much more powerful and consise way of defining a layout such as the one above that is actually simpler and much more logical to design. The basic building blocks are the panelGridLayout itself, gridRow and gridCell. Your content sits inside the cells inside the rows, all helpfully allowing both streching, valign and halign definitions without the need to nest further panelGroupLayouts. So much simpler!  If I break down the homework example above my nested comglomorate of 12 containers and spacers can be condensed down into a single panelGrid with 3 rows and 5 cell definitions (39 lines of source reduced to 24 in the case of the sample). What's more, the actual runtime representation in the browser DOM is much, much simpler, and clean, with basically one DIV per cell (Note that just because the panelGridLayout semantics looks like an HTML table does not mean that it's rendered that way!) . Another hidden benefit is the runtime cost. Because we can use a single layout to achieve much more complex geometries the client side layout code inside the browser is having to work a lot less. This will be a real benefit if your application needs to run on lower powered clients such as netbooks or tablets. So, it's time, if you're on 11.1.2.2 or above, to smile warmly at your panelStretchLayouts, wrap the blanket around it's knees and wheel it off to the Sunset Retirement Home for a well deserved rest. There's a new kid on the block and it wants to be your friend. 

  Read the article

• My error with upgrading 4.0 to 4.2- What NOT to do...

  - by Steve Tunstall

  Last week, I was helping a client upgrade from the 2011.1.4.0 code to the newest 2011.1.4.2 code. We downloaded the 4.2 update from MOS, upload and unpacked it on both controllers, and upgraded one of the controllers in the cluster with no issues at all. As this was a brand-new system with no networking or pools made on it yet, there were not any resources to fail back and forth between the controllers. Each controller had it's own, private, management interface (igb0 and igb1) and that's it. So we took controller 1 as the passive controller and upgraded it first. The first controller came back up with no issues and was now on the 4.2 code. Great. We then did a takeover on controller 1, making it the active head (although there were no resources for it to take), and then proceeded to upgrade controller 2. Upon upgrading the second controller, we ran the health check with no issues. We then ran the update and it ran and rebooted normally. However, something strange then happened. It took longer than normal to come back up, and when it did, we got the "cluster controllers on different code" error message that one gets when the two controllers of a cluster are running different code. But we just upgraded the second controller to 4.2, so they should have been the same, right??? Going into the Maintenance-->System screen of controller 2, we saw something very strange. The "current version" was still on 4.0, and the 4.2 code was there but was in the "previous" state with the rollback icon, as if it was the OLDER code and not the newer code. I have never seen this happen before. I would have thought it was a bad 4.2 code file, but it worked just fine with controller 1, so I don't think that was it. Other than the fact the code did not update, there was nothing else going on with this system. It had no yellow lights, no errors in the Problems section, and no errors in any of the logs. It was just out of the box a few hours ago, and didn't even have a storage pool yet. So.... We deleted the 4.2 code, uploaded it from scratch, ran the health check, and ran the upgrade again. once again, it seemed to go great, rebooted, and came back up to the same issue, where it came to 4.0 instead of 4.2. See the picture below.... HERE IS WHERE I MADE A BIG MISTAKE.... I SHOULD have instantly called support and opened a Sev 2 ticket. They could have done a shared shell and gotten the correct Fishwork engineer to look at the files and the code and determine what file was messed up and fixed it. The system was up and working just fine, it was just on an older code version, not really a huge problem at all. Instead, I went ahead and clicked the "Rollback" icon, thinking that the system would rollback to the 4.2 code.   Ouch... What happened was that the system said, "Fine, I will delete the 4.0 code and boot to your 4.2 code"... Which was stupid on my part because something was wrong with the 4.2 code file here and the 4.0 was just fine.  So now the system could not boot at all, and the 4.0 code was completely missing from the system, and even a high-level Fishworks engineer could not help us. I had messed it up good. We could only get to the ILOM, and I had to re-image the system from scratch using a hard-to-get-and-use FishStick USB drive. These are tightly controlled and difficult to get, almost always handcuffed to an engineer who will drive out to re-image a system. This took another day of my client's time.  So.... If you see a "previous version" of your system code which is actually a version higher than the current version... DO NOT ROLL IT BACK.... It did not upgrade for a very good reason. In my case, after the system was re-imaged to a code level just 3 back, we once again tried the same 4.2 code update and it worked perfectly the first time and is now great and stable.  Lesson learned.  By the way, our buddy Ryan Matthews wanted to point out the best practice and supported way of performing an upgrade of an active/active ZFSSA, where both controllers are doing some of the work. These steps would not have helpped me for the above issue, but it's important to follow the correct proceedure when doing an upgrade. 1) Upload software to both controllers and wait for it to unpack 2) On controller "A" navigate to configuration/cluster and click "takeover" 3) Wait for controller "B" to finish restarting, then login to it, navigate to maintenance/system, and roll forward to the new software. 4) Wait for controller "B" to apply the update and finish rebooting 5) Login to controller "B", navigate to configuration/cluster and click "takeover" 6) Wait for controller "A" to finish restarting, then login to it, navigate to maintenance/system, and roll forward to the new software. 7) Wait for controller "A" to apply the update and finish rebooting 8) Login to controller "B", navigate to configuration/cluster and click "failback"

  Read the article

• Best Practices Generating WebService Proxies for Oracle Sales Cloud (Fusion CRM)

  - by asantaga

  I've recently been building a REST Service wrapper for Oracle Sales Cloud and initially all was going well, however as soon as I added all of my Web Service proxies I started to get weird errors..  My project structure looks like this What I found out was if I only had the InteractionsService & OpportunityService WebService Proxies then all worked ok, but as soon as I added the LocationsService Proxy, I would start to see strange JAXB errors. Example of the error message Exception in thread "main" javax.xml.ws.WebServiceException: Unable to create JAXBContextat com.sun.xml.ws.model.AbstractSEIModelImpl.createJAXBContext(AbstractSEIModelImpl.java:164)at com.sun.xml.ws.model.AbstractSEIModelImpl.postProcess(AbstractSEIModelImpl.java:94)at com.sun.xml.ws.model.RuntimeModeler.buildRuntimeModel(RuntimeModeler.java:281)at com.sun.xml.ws.client.WSServiceDelegate.buildRuntimeModel(WSServiceDelegate.java:762)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.buildRuntimeModel(WLSProvider.java:982)at com.sun.xml.ws.client.WSServiceDelegate.createSEIPortInfo(WSServiceDelegate.java:746)at com.sun.xml.ws.client.WSServiceDelegate.addSEI(WSServiceDelegate.java:737)at com.sun.xml.ws.client.WSServiceDelegate.getPort(WSServiceDelegate.java:361)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.internalGetPort(WLSProvider.java:934)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate$PortClientInstanceFactory.createClientInstance(WLSProvider.java:1039)...... Looking further down I see the error message is related to JAXB not being able to find an objectFactory for one of its types Caused by: java.security.PrivilegedActionException: com.sun.xml.bind.v2.runtime.IllegalAnnotationsException: 6 counts of IllegalAnnotationExceptionsThere's no ObjectFactory with an @XmlElementDecl for the element {http://xmlns.oracle.com/apps/crmCommon/activities/activitiesService/}AssigneeRsrcOrgIdthis problem is related to the following location:at protected javax.xml.bind.JAXBElement com.oracle.xmlns.apps.crmcommon.activities.activitiesservice.ActivityAssignee.assigneeRsrcOrgId at com.oracle.xmlns.apps.crmcommon.activities.activitiesservice.ActivityAssignee This is very strange... My first thoughts are that when I generated the WebService Proxy I entered the package name as "oracle.demo.pts.fusionproxy.servicename" and left the generated types as blank. This way all the generated types get put into the same package hierarchy and when deployed they get merged... Sounds resaonable and appears to work but not in this case..  To resolve this I regenerate the proxy but this time setting : Package name : To the name of my package eg. oracle.demo.pts.fusionproxy.interactionsRoot Package for Generated Types :  Package where the types will be generated to, e.g. oracle.demo.pts.fusionproxy.SalesParty.types When I ran the application now, it all works , awesome eh???? Alas no, there is a serious side effect. The problem now is that to help coding I've created a collection of helper classes , these helper classes take parameters which use some of the "generic" datatypes, like FindCriteria. e.g. This wont work any more public static FindCriteria createCustomFindCriteria(FindCriteria pFc,String pAttributes) Here lies a gremlin of a problem.. I cant use this method anymore, this is because the FindCriteria datatype is now being defined two, or more times, in the generated code for my project. If you leave the Root Package for types blank it will get generated to com.oracle.xmlns, and if you populate it then it gets generated to your custom package.. The two datatypes look the same, sound the same (and if this were a duck would sound the same), but THEY ARE NOT THE SAME... Speaking to development, they recommend you should not be entering anything in the Root Packages section, so the mystery thickens why does it work.. Well after spending sometime with some colleagues of mine in development we've identified the issue.. Alas different parts of Oracle Fusion Development have multiple schemas with the same namespace, when the WebService generator generates its classes its not seeing the other schemas properly and not generating the Object Factories correctly...  Thankfully I've found a workaround Solution Overview When generating the proxies leave the Root Package for Generated Types BLANK When you have finished generating your proxies, use the JAXB tool XJC and generate Java classes for all datatypes  Create a project within your JDeveloper11g workspace and import the java classes into this project Final bit.. within the project dependencies ensure that the JAXB/XJC generated classes are "FIRST" in the classpath Solution Details Generate the WebServices SOAP proxies When generating the proxies your generation dialog should look like this Ensure the "unwrap" parameters is selected, if it isn't then that's ok, it simply means when issuing a "get" you need to extract out the Element Generate the JAXB Classes using XJC XJC provides a command line switch called -wsdl, this (although is experimental/beta) , accepts a HTTP WSDL and will generate the relevant classes. You can put these into a single batch/shell script xjc -wsdl https://fusionservername:443/appCmmnCompInteractions/InteractionService?wsdlxjc -wsdl https://fusionservername443/opptyMgmtOpportunities/OpportunityService?wsdl Create Project in JDeveloper to store the XJC "generated" JAXB classes Within the project folder create a filesystem folder called "src" and copy the generated files into this folder. JDeveloper11g should then see the classes and display them, if it doesnt try clicking the "refresh" button In your main project ensure that the JDeveloper XJC project is selected as a dependancy and IMPORTANT make sure it is at the top of the list. This ensures that the classes are at the front of the classpath And voilà.. Hopefully you wont see any JAXB generation errors and you can use common datatypes interchangeably in your project, (e.g. FindCriteria etc)

  Read the article

• Time to Get Started with Oracle Data Integrator 12c!

  - by Sandrine Riley

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} It is time to get started with Oracle Data Integrator 12c! We would like to highlight for you a great place to begin your journey with ODI.  Here you will find the Getting Started section for ODI, which provides a few options. v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} Step 1 – Start by downloading the Getting Started (PDF). The document provides general background information and detailed examples to help you learn how to use Oracle Data Integrator. This document guides you through a first project with Oracle Data Integrator 12c, and the instructions in this document are required for using the Getting Started Demonstration Environment. If you would like to run the Getting Started Demonstration Environment on your system go to Step 2 A. If you would like to run the Getting Started Demonstration Environment installed and pre-configured in a Virtual Image, go to Step 2 B. Step 2 - A-   A -  If you would like to run the Getting Started Demo Environment on your system, you will want to then download the Demo Environment for Getting Started (ZIP) archive containing ODI metadata, configuration scripts and sample data. B-   B -  Alternatively, a pre-configured virtual machine is available with the Getting Started installation and configuration. The Virtual Machine platform uses Oracle Virtual Box technology, and use of this configuration would necessitate the download/installation of Virtual Box and the Getting Started virtual machine. If you prefer this route and would rather run the Getting Started Demonstration Environment installed and preconfigured in a Virtual Machine, please download the ODI 12c Getting Started Virtual Machine. Step 3 – In continuation with the Getting Started Demonstration Environment and the Getting Started Guide, you will now be able to run through a first project with Oracle Data Integrator. Now that you have successfully done the exercises above, you may want to play on your own, and develop with Oracle Data Integrator on your environment...  here you can download a full version of Oracle Data Integrator 12c.  Enjoy, and happy developing! Learn more about Oracle Data Integrator; including FAQ, the Oracle by Example Series, Sample Code, and White Papers. Normal 0 false false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;}

  Read the article

• ndd on Solaris 10

  - by user12620111

  This is mostly a repost of LaoTsao's Weblog with some tweaks. Last time that I tried to cut & paste directly off of his page, some of the XML was messed up. I run this from my MacBook. It should also work from your windows laptop if you use cygwin. ================If not already present, create a ssh key on you laptop================ # ssh-keygen -t rsa ================ Enable passwordless ssh from my laptop. Need to type in the root password for the remote machines. Then, I no longer need to type in the password when I ssh or scp from my laptop to servers. ================ #!/usr/bin/env bash for server in `cat servers.txt` do   echo root@$server   cat ~/.ssh/id_rsa.pub | ssh root@$server "cat >> .ssh/authorized_keys" done ================ servers.txt ================ testhost1testhost2 ================ etc_system_addins ================ set rpcmod:clnt_max_conns=8 set zfs:zfs_arc_max=0x1000000000 set nfs:nfs3_bsize=131072 set nfs:nfs4_bsize=131072 ================ ndd-nettune.txt ================ #!/sbin/sh # # ident   "@(#)ndd-nettune.xml    1.0     01/08/06 SMI" . /lib/svc/share/smf_include.sh . /lib/svc/share/net_include.sh # Make sure that the libraries essential to this stage of booting  can be found. LD_LIBRARY_PATH=/lib; export LD_LIBRARY_PATH echo "Performing Directory Server Tuning..." >> /tmp/smf.out # # Standard SuperCluster Tunables # /usr/sbin/ndd -set /dev/tcp tcp_max_buf 2097152 /usr/sbin/ndd -set /dev/tcp tcp_xmit_hiwat 1048576 /usr/sbin/ndd -set /dev/tcp tcp_recv_hiwat 1048576 # Reset the library path now that we are past the critical stage unset LD_LIBRARY_PATH ================ ndd-nettune.xml ================ <?xml version="1.0"?> <!DOCTYPE service_bundle SYSTEM "/usr/share/lib/xml/dtd/service_bundle.dtd.1"> <!-- ident "@(#)ndd-nettune.xml 1.0 04/09/21 SMI" --> <service_bundle type='manifest' name='SUNWcsr:ndd'>   <service name='network/ndd-nettune' type='service' version='1'>     <create_default_instance enabled='true' />     <single_instance />     <dependency name='fs-minimal' type='service' grouping='require_all' restart_on='none'>       <service_fmri value='svc:/system/filesystem/minimal' />     </dependency>     <dependency name='loopback-network' grouping='require_any' restart_on='none' type='service'>       <service_fmri value='svc:/network/loopback' />     </dependency>     <dependency name='physical-network' grouping='optional_all' restart_on='none' type='service'>       <service_fmri value='svc:/network/physical' />     </dependency>     <exec_method type='method' name='start' exec='/lib/svc/method/ndd-nettune' timeout_seconds='3' > </exec_method>     <exec_method type='method' name='stop'  exec=':true'                       timeout_seconds='3' > </exec_method>     <property_group name='startd' type='framework'>       <propval name='duration' type='astring' value='transient' />     </property_group>     <stability value='Unstable' />     <template>       <common_name>     <loctext xml:lang='C'> ndd network tuning </loctext>       </common_name>       <documentation>     <manpage title='ndd' section='1M' manpath='/usr/share/man' />       </documentation>     </template>   </service> </service_bundle> ================ system_tuning.sh ================ #!/usr/bin/env bash for server in `cat servers.txt` do   cat etc_system_addins | ssh root@$server "cat >> /etc/system"   scp ndd-nettune.xml root@${server}:/var/svc/manifest/site/ndd-nettune.xml   scp ndd-nettune.txt root@${server}:/lib/svc/method/ndd-nettune   ssh root@$server chmod +x /lib/svc/method/ndd-nettune   ssh root@$server svccfg validate /var/svc/manifest/site/ndd-nettune.xml   ssh root@$server svccfg import /var/svc/manifest/site/ndd-nettune.xml done

  Read the article

• HTML5 Form: Page Is Reloading Instantly After Restyling (And It Shouldn't Be)

  - by user3689753

  I have a form. I have made it so that if your name is not put in, a red border is put on the name field. That works, BUT...it's for a split second, and then the page reloads. I want the red border to appear, and then stay there. For some reason it's for a split second. Can someone help me make it so the page doesn't reload after displaying the red border? Here's the script. window.onload = function() { document.getElementById("Hogwarts").onsubmit = function () { window.alert("Form submitted. Owl being sent..."); var fname = document.getElementById("fName"); if(!fName.value.match("^[A-Z][A-Za-z]+( [A-Z][A-Za-z]*)*$")) { window.alert("You must enter your name."); addClass(fName, "errorDisp"); document.getElementById("fName").focus(); } else return true; } } function addClass(element, classToAdd) { var currentClassValue = element.className; if (currentClassValue.indexOf(classToAdd) == -1) { if ((currentClassValue == null) || (currentClassValue === "")) { element.className = classToAdd; } else { element.className += " " + classToAdd; } } } function removeClass(element, classToRemove) { var currentClassValue = element.className; if (currentClassValue == classToRemove) { element.className = ""; return; } var classValues = currentClassValue.split(" "); var filteredList = []; for (var i = 0 ; i < classValues.length; i++) { if (classToRemove != classValues[i]) { filteredList.push(classValues[i]); } } element.className = filteredList.join(" "); } Here's the HTML. <!DOCTYPE HTML> <html lang="en"> <head> <meta charset="UTF-8" /> <meta name="viewport" content="width=device-width, initial-scale=1, maximum-scale=1"> <title>Hogwarts School of Witchcraft And Wizardry Application Form</title> <link rel="stylesheet" type="text/css" href="main.css" media="screen"/> <script src="script.js" type="text/javascript"></script> </head> <body> <section> <header> <h1>Hogwarts School of Witchcraft And Wizardry</h1> <nav></nav> </header> <main> <form method="post" id="Hogwarts"> <!--<form action="showform.php" method="post" id="Hogwarts">--!> <fieldset id="aboutMe"> <legend id="aboutMeLeg">About Me</legend> <div class="fieldleading"> <label for="fName" class="labelstyle">First name:</label> <input type="text" id="fName" name="fName" autofocus maxlength="50" value="" placeholder="First Name" size="30"> <label for="lName" class="labelstyle">Last name:</label> <input type="text" id="lName" name="lName" required maxlength="50" value="" placeholder="Last Name" pattern="^[A-Za-z ]{3,}$" size="30"> <label for="age" class="labelstyle">Age:</label> <input type="number" id="age" name="age" required min="17" step="1" max="59" value="" placeholder="Age"> </div> <div class="fieldleading"> <label for="date" class="labelstyle">Date Of Birth:</label> <input type="date" name="date1" id="date" required autofocus value=""> </div> <div id="whitegender"> <div class="fieldleading"> <label class="labelstyle">Gender:</label> </div> <input type="radio" name="sex" value="male" class="gender" required="required">Male<br/> <input type="radio" name="sex" value="female" class="gender" required="required">Female<br/> <input type="radio" name="sex" value="other" class="gender" required="required">Other </div> </fieldset> <fieldset id="contactInfo"> <legend id="contactInfoLeg">Contact Information</legend> <div class="fieldleading"> <label for="street" class="labelstyle">Street Address:</label> <input type="text" id="street" name="street" required autofocus maxlength="50" value="" placeholder="Street Address" pattern="^[0-9A-Za-z\. ]+{5,}$" size="35"> <label for="city" class="labelstyle">City:</label> <input type="text" id="city" name="city" required autofocus maxlength="30" value="" placeholder="City" pattern="^[A-Za-z ]{3,}$" size="35"> <label for="State" class="labelstyle">State:</label> <select required id="State" name="State" > <option value="Select Your State">Select Your State</option> <option value="Delaware">Delaware</option> <option value="Pennsylvania">Pennsylvania</option> <option value="New Jersey">New Jersey</option> <option value="Georgia">Georgia</option> <option value="Connecticut">Connecticut</option> <option value="Massachusetts">Massachusetts</option> <option value="Maryland">Maryland</option> <option value="New Hampshire">New Hampshire</option> <option value="New York">New York</option> <option value="Virginia">Virginia</option> </select> </div> <div class="fieldleading"> <label for="zip" class="labelstyle">5-Digit Zip Code:</label> <input id="zip" name="zip" required autofocus maxlength="5" value="" placeholder="Your Zip Code" pattern="^\d{5}$"> <label for="usrtel" class="labelstyle">10-Digit Telephone Number:</label> <input type="tel" name="usrtel" id="usrtel" required autofocus value="" placeholder="123-456-7890" pattern="^\d{3}[\-]\d{3}[\-]\d{4}$"> </div> <div class="fieldleading"> <label for="email1" class="labelstyle">Email:</label> <input type="email" name="email1" id="email1" required autofocus value="" placeholder="[email protected]" pattern="^[a-z0-9._%+-]+@[a-z0-9.-]+\.[a-z]{2,4}$" size="35"> <label for="homepage1" class="labelstyle">Home Page:</label> <input type="url" name="homepage1" id="homepage1" required autofocus value="" placeholder="http://www.hp.com" pattern="https?://.+" size="35"> </div> </fieldset> <fieldset id="yourInterests"> <legend id="yourInterestsLeg">Your Interests</legend> <label for="Major" class="labelstyle">Major/Program Choice:</label> <select required id="Major" name="Major" > <option value="">Select Your Major</option> <option value="Magic1">Magic Horticulture</option> <option value="Magic2">Black Magic</option> <option value="White">White Magic</option> <option value="Blue">Blue Magic</option> <option value="Non">Non-Wizardry Studies</option> </select> </fieldset> <button type="submit" value="Submit" class="submitreset">Submit</button> <button type="reset" value="Reset" class="submitreset">Reset</button> </form> </main> <footer> &copy; 2014 Bennett Nestok </footer> </section> </body> </html> Here's the CSS. a:link { text-decoration: none !important; color:black !important; } a:visited { text-decoration: none !important; color:red !important; } a:active { text-decoration: none !important; color:green !important; } a:hover { text-decoration: none !important; color:blue !important; background-color:white !important; } ::-webkit-input-placeholder { color: #ffffff; } /* gray80 */ :-moz-placeholder { color: #ffffff; } /* Firefox 18- (one color)*/ ::-moz-placeholder { color: #ffffff; } /* Firefox 19+ (double colons) */ :-ms-input-placeholder { color: #ffffff; } body { margin: 0px auto; text-align:center; background-color:grey; font-weight:normal; font-size:12px; font-family: verdana; color:black; background-image:url('bgtexture.jpg'); background-repeat:repeat; } footer { text-align:center; margin: 0px auto; bottom:0px; position:absolute; width:100%; color:white; background-color:black; height:20px; padding-top:4px; } h1 { color:white; text-align:center; margin: 0px auto; margin-bottom:50px; width:100%; background-color:black; padding-top: 13px; padding-bottom: 14px; -moz-box-shadow: 0 1px 3px rgba(0,0,0,0.5); -webkit-box-shadow: 0 1px 3px rgba(0,0,0,0.5); text-shadow: 0 -1px 1px rgba(0,0,0,0.25); } button.submitreset { -moz-border-radius: 400px; -webkit-border-radius: 400px; border-radius: 400px; -moz-box-shadow: 0 1px 3px rgba(0,0,0,0.5); -webkit-box-shadow: 0 1px 3px rgba(0,0,0,0.5); text-shadow: 0 -1px 1px rgba(0,0,0,0.25); } .labelstyle { background-color:#a7a7a7; color:black; -moz-border-radius: 400px; -webkit-border-radius: 400px; border-radius: 400px; padding:3px 3px 3px 3px; } #aboutMe, #contactInfo, #yourInterests { margin-bottom:30px; text-align:left !important; padding: 10px 10px 10px 10px; } #Hogwarts { text-align:center; margin:0px auto; width:780px; padding-top: 20px !important; padding-bottom: 20px !important; background: -webkit-linear-gradient(#474747, grey); /* For Safari 5.1 to 6.0 */ background: -o-linear-gradient(#474747, grey); /* For Opera 11.1 to 12.0 */ background: -moz-linear-gradient(#474747, grey); /* For Firefox 3.6 to 15 */ background: linear-gradient(#474747, grey); /* Standard syntax */ border-color:black; border-style: solid; border-width: 2px; -moz-box-shadow: 0 1px 3px rgba(0,0,0,0.5); -webkit-box-shadow: 0 1px 3px rgba(0,0,0,0.5); text-shadow: 0 -1px 1px rgba(0,0,0,0.25); } @media (max-width: 800px){ .labelstyle { display: none; } #Hogwarts { width:300px; } h1 { width:304px; margin-bottom:0px; } .fieldleading { margin-bottom:0px !important; } ::-webkit-input-label { /* WebKit browsers */ color: transparent; } :-moz-label { /* Mozilla Firefox 4 to 18 */ color: transparent; } ::-moz-label { /* Mozilla Firefox 19+ */ color: transparent; } :-ms-input-label { /* Internet Explorer 10+ */ color: transparent; } ::-webkit-input-placeholder { /* WebKit browsers */ color: grey !important; } :-moz-placeholder { /* Mozilla Firefox 4 to 18 */ color: grey !important; } ::-moz-placeholder { /* Mozilla Firefox 19+ */ color: grey !important; } :-ms-input-placeholder { /* Internet Explorer 10+ */ color: grey !important; } #aboutMe, #contactInfo, #yourInterests { margin-bottom:10px; text-align:left !important; padding: 5px 5px 5px 5px; } } br { display: block; line-height: 10px; } .fieldleading { margin-bottom:10px; } legend { color:white; } #whitegender { color:white; } #moreleading { margin-bottom:10px; } /*opera only hack attempt*/ @media not all and (-webkit-min-device-pixel-ratio:0) { .fieldleading { margin-bottom:30px !important; } } .errorDisp { border-color: red; border-style: solid; border-width: 2px; }

  Read the article

• Data Source Security Part 4

  - by Steve Felts

  So far, I have covered Client Identity and Oracle Proxy Session features, with WLS or database credentials.  This article will cover one more feature, Identify-based pooling.  Then, there is one more topic to cover - how these options play with transactions.Identity-based Connection Pooling An identity based pool creates a heterogeneous pool of connections.  This allows applications to use a JDBC connection with a specific DBMS credential by pooling physical connections with different DBMS credentials.  The DBMS credential is based on either the WebLogic user mapped to a database user or the database user directly, based on the “use database credentials” setting as described earlier. Using this feature enabled with “use database credentials” enabled seems to be what is proposed in the JDBC standard, basically a heterogeneous pool with users specified by getConnection(user, password). The allocation of connections is more complex if Enable Identity Based Connection Pooling attribute is enabled on the data source.  When an application requests a database connection, the WebLogic Server instance selects an existing physical connection or creates a new physical connection with requested DBMS identity. The following section provides information on how heterogeneous connections are created:1. At connection pool initialization, the physical JDBC connections based on the configured or default “initial capacity” are created with the configured default DBMS credential of the data source.2. An application tries to get a connection from a data source.3a. If “use database credentials” is not enabled, the user specified in getConnection is mapped to a DBMS credential, as described earlier.  If the credential map doesn’t have a matching user, the default DBMS credential is used from the datasource descriptor.3b. If “use database credentials” is enabled, the user and password specified in getConnection are used directly.4. The connection pool is searched for a connection with a matching DBMS credential.5. If a match is found, the connection is reserved and returned to the application.6. If no match is found, a connection is created or reused based on the maximum capacity of the pool: - If the maximum capacity has not been reached, a new connection is created with the DBMS credential, reserved, and returned to the application.- If the pool has reached maximum capacity, based on the least recently used (LRU) algorithm, a physical connection is selected from the pool and destroyed. A new connection is created with the DBMS credential, reserved, and returned to the application. It should be clear that finding a matching connection is more expensive than a homogeneous pool.  Destroying a connection and getting a new one is very expensive.  If you can use a normal homogeneous pool or one of the light-weight options (client identity or an Oracle proxy connection), those should be used instead of identity based pooling. Regardless of how physical connections are created, each physical connection in the pool has its own DBMS credential information maintained by the pool. Once a physical connection is reserved by the pool, it does not change its DBMS credential even if the current thread changes its WebLogic user credential and continues to use the same connection. To configure this feature, select Enable Identity Based Connection Pooling.  See http://docs.oracle.com/cd/E24329_01/apirefs.1211/e24401/taskhelp/jdbc/jdbc_datasources/EnableIdentityBasedConnectionPooling.html  "Enable identity-based connection pooling for a JDBC data source" in Oracle WebLogic Server Administration Console Help. You must make the following changes to use Logging Last Resource (LLR) transaction optimization with Identity-based Pooling to get around the problem that multiple users will be accessing the associated transaction table.- You must configure a custom schema for LLR using a fully qualified LLR table name. All LLR connections will then use the named schema rather than the default schema when accessing the LLR transaction table.  - Use database specific administration tools to grant permission to access the named LLR table to all users that could access this table via a global transaction. By default, the LLR table is created during boot by the user configured for the connection in the data source. In most cases, the database will only allow access to this user and not allow access to mapped users. Connections within Transactions Now that we have covered the behavior of all of these various options, it’s time to discuss the exception to all of the rules.  When you get a connection within a transaction, it is associated with the transaction context on a particular WLS instance. When getting a connection with a data source configured with non-XA LLR or 1PC (using the JTS driver) with global transactions, the first connection obtained within the transaction is returned on subsequent connection requests regardless of the values of username/password specified and independent of the associated proxy user session, if any. The connection must be shared among all users of the connection when using LLR or 1PC. For XA data sources, the first connection obtained within the global transaction is returned on subsequent connection requests within the application server, regardless of the values of username/password specified and independent of the associated proxy user session, if any.  The connection must be shared among all users of the connection within a global transaction within the application server/JVM.

  Read the article

• how to run mysql drop and create synonym in shell script

  - by bgrif

  I have added this command to a script I am writing and I am running into a issue with it not logging onto mysql and running the commands. How can i fix this and make it run. #! /bin/bash Subject: Please stage the following TFL09143 Locator Bulletin to all TF90 staging environments: # This next section is to go to mysql server and make changes. you can drop and create synonyms truncate a table and insert into a different one. you will be able to verify the counts to the different locations # $ mysql --host=app03-bsi --u "" --p "" "TF90BPS" -bse "drop synonym TF90.BTXADDR && drop synonym TF90.BTXSUPB && CREATE SYNONYM TF90.BTXADDR FOR TF90BP.TFBPS2.BTXADDR && CREATE SYNONYM TF90.BTXSUPB FOR TF90BP.TFBPS3.BTXSUPB && TRUNCATE TABLE TF90BP.TFBPS3.BTXSUPB SELECT * FROM TF90BP.TFBPS2.BTXSUPB; select count () from TF90BP.TF90.BTXADDR select count() from TF90BPS.TF90.BTXADDR; select count() from TF90BP.TF90.BTXSUPB; select count() from TF90BPS.TF90.BTXSUPB;" $ mysql --host=app03-bsi --u "" --p "" "TF90LMS" -bse "drop synonym TF90.BTXADDR && drop synonym TF90.BTXSUPB && CREATE SYNONYM TF90.BTXADDR FOR TF90LM.TFBPS2.BTXADDR && CREATE SYNONYM TF90.BTXSUPB FOR TF90LM.TFBPS3.BTXSUPB; TRUNCATE TABLE TF90LM.TFLMS2.BTXADDR;TRUNCATE TABLE TF90LM.TFLMS3.BTXSUPB;INSERT INTO TF90LM.TFLMS3.BTXSUPB SELECT * FROM TF90LM.TFLMS2.BTXSUPB;Verify select count() from TF90LM.TF90.BTXADDR;select count() from TF90LMS.TF90.BTXADDR;select count() from TF90LM.TF90.BTXSUPB;select count() from TF90LMS.TF90.BTXSUPB" $ mysql --host=app03-bsi --u "" --p "" "TF90NCS" -bse "drop synonym TF90.BTXADDR && drop synonym TF90.BTXSUPB && CREATE SYNONYM TF90.BTXADDR FOR TF90NC.TFBPS2.BTXADDR && CREATE SYNONYM TF90.BTXSUPB FOR TF90NC.TFBPS3.BTXSUPB; TRUNCATE TABLE TF90NC.TFNCS2.BTXADDR; TRUNCATE TABLE TF90NC.TFNCS3.BTXSUPB; INSERT INTO TF90NC.TFNCS3.BTXSUPB SELECT * FROM TF90NC.TFNCS2.BTXSUPB; Verify select count() from TF90NC.TF90.BTXADDR; select count() from TF90NCS.TF90.BTXADDR;select count() from TF90NC.TF90.BTXSUPB;select count() from TF90NCS.TF90.BTXSUPB" $ mysql --host=app03-bsi --u "" --p "" "TF90PVS" -bse "drop synonym TF90.BTXADDR && drop synonym TF90.BTXSUPB && CREATE SYNONYM TF90.BTXADDR FOR TF90PV.TFBPS2.BTXADDR && CREATE SYNONYM TF90.BTXSUPB FOR TF90PV.TFBPS3.BTXSUPB; TRUNCATE TABLE TF90PV.TFPVS2.BTXADDR;TRUNCATE TABLE TF90PV.TFPVS3.BTXSUPB;INSERT INTO TF90PV.TFPVS3.BTXSUPB SELECT * FROM TF90PV.TFPVS2.BTXSUPB;Verify select count() from TF90PV.TF90.BTXADDR;select count() from TF90PVS.TF90.BTXADDR;select count() from TF90PV.TF90.BTXSUPB;select count() from TF90PVS.TF90.BTXSUPB" TFL09143 Staging cd \ntsrv\common\To\IT-CERT-TEST\TFL09143 #change to mapped network drive cp -p TFL09143.pkg /d:/tf90/code_stg && /tf90bp/code_stg && /tf90lm/code_stg && /tf90pv/code_stg # Copies the package from the networked folder and then copies to the location(s) needed.# InvalidInput="true" if [ $# -eq 0 ] ; then echo "This script sets up TF90 Staging" echo -n "Which production do you want to run? (RB/TaxLocator/Cyclic)" read ProductionDistro else ProductionDistro="$1" fi while [ "$InvalidInput" = "true" ] do if [ "$ProductionDistro" = "RB" -o "$ProductionDistro" = "TaxLocator" -o "$ProductionDistro" = "Cyclic" ] ; then InvalidInput="false" break else echo "You have entered an error" echo "You must type RB or TaxLocator or Cyclic" echo "you typed $ProductionDistro" echo "This script sets up TF90 Staging" read ProductionDistro fi done InvalidInput="true" if [ $# -eq 0 ] ; then echo "This script sets up RB TF90 Staging" echo -n "Which Element do you want to run? (TF90/TF90BP/TF90LM/TF90PV/ALL)" read ElementDistro else ElementDistro="$1" fi while [ "$InvalidInput" = "true" ] do if [ "$ElementDistro" = "TF90" -o "$ElementDistro" = "TF90BP" -o "$ElementDistro" = "TF90LM" -o "$ElementDistro" = "TF90PV" -o "$ElementDistro" = "ALL" ] ; then InvalidInput="false" break else echo "You have entered an error" echo "You must type TF90 or TF90BP or TF90LM or TF90PV" echo "you typed $ElementDistro" echo "This script sets up TF90 Staging" read ElementDistro fi done if [ "$ElementDistro" = "TF90" ] ; then cd /d/tf90/code_stg vim TFL09143.pkg export var=TF90_CONNECT_STRING=DSN=TF90NCS;export Description=TF90NCS;export Trusted_Connection=Yes;export WSID=APP03- BSI;export DATABASE=TF90NCS; export DATASET=DEFAULT pkgintall -l -v ../TFL09143.pkg fi if [ "$ElementDistro" = "$TF90BP" ] ; then cd /d/tf90bp/code_stg vim TFL09143.pkg export TF90_CONNECT_STRING=DSN=TF90BPS;export Description=TF90BPS;export Trusted_Connection=Yes;export WSID=APP03- BSI;export DATABASE=TF90BPS; start tfloader -l –v ../TFL09143.pkg fi if [ "$ElementDistro" = "$TF90LM" ] ; then cd /d/tf90lm/code_stg vim TFL09143.pkg export TF90_CONNECT_STRING=DSN=TF90LMS;export Description=TF90LMS;export Trusted_Connection=Yes;export WSID=APP03- BSI;export DATABASE=TF90LMS; start tfloader -l -v ../TFL09143.pkg fi if [ "$ElementDistro" = "TF90PV" ] ; then cd /d/tf90pv/code_stg vim TFL09143.pkg export TF90_CONNECT_STRING=DSN=TF90PVS;Description=TF90PVS;Trusted_Connection=Yes;WSID=APP03- BSI;DATABASE=TF90PVS; start tfloader -l –v ../TFL09143.pkg fi exit 0

  Read the article

• Tweaking Hudson memory usage

  - by rovarghe

  Hudson 3.1 has some performance optimizations that greatly reduces its memory footprint. Prior to this Hudson used to always hold the entire data model (all jobs and all builds) in memory which affected scalability. Some installations configured heap sizes in excess of 1GB to counteract this. Hudson 3.1.x maintains an MRU cache and only loads jobs and builds as they are required. Because of the inability to change existing APIs and be backward compatible with plugins, there were limits to how far we could go with this approach. Memory optimizations almost always come with a related cost, in this case its additional I/O that has to be performed to load data on request. On a small site that has frequent traffic, this is usually not noticeable since the MRU cache will usually hold on to all the data. A large site with infrequent traffic might experience some delays when the first request hits the server after a long gap. If you have a large heap and are able to allocate more memory, the cache settings can be adjusted to take advantage of this and even go back to pre-3.1 behavior. All the cache settings can be passed as options to the JVM container (Tomcat or the default Jetty container) using the -D option. There are two caches, independant of each other, one for Jobs and the other for Builds. For the jobs cache: hudson.jobs.cache.evict_in_seconds ( default=60 ) Seconds from last access (could be because of a servlet request or a background cron thread) a job should be purged from the cache. Set this to 0 to never purge based on time. hudson.jobs.cache.initial_capacity ( default=1024 ) Initial number of jobs the cache can accomodate. Setting this to the number of jobs you typically display on your Hudson landing page or home page will speed up consecutive access to that page. If the default is too large you may consider downsizing and using that memory for the Builds cache instead. hudson.jobs.cache.max_entries ( default=1024) Maximum number of jobs in the cache. The default is large enough for most installations, but if you find I/O activity when always accessing the hudson home page you might consider increasing this, but first verify if the I/O is caused by frequent eviction (see above), rather than by the cache not being large enough. For the builds cache: The builds cache is used to store Build objects as they are read from storage. Typically this happens when a user drills down into the details of a particular Job from the hudson hom epage. The cache is shared among builds for different jobs since in most installations all jobs are not accessed with the same frequency, so a per-job builds cache would be a waste of memory. hudson.job.builds.cache.evict_in_seconds ( default=60 ) Same as the equivalent Job cache, applied to Build. hudson.job.builds.cache.initial_capacity" ( default=512 ) Same as equivalent Job cache setting. Note the smaller initial size. If your site stores a large number of builds and has frequent access to more builds you might consider bumping this up. hudson.job.builds.cache.max_entries ( default=10240 ) The default max is large enough for most installations, the builds cache has bigger sized objects, so be careful about increasing the upper limit on this. See section on monitoring below. Sample usage: java -jar hudson-war-3.1.2-SNAPSHOT.war -Dhudson.jobs.cache.evict_in_seconds=300 \ -Dhudson.job.builds.cache.evict_in_seconds=300 Monitoring cache usage The 'jmap' tool that comes with the JDK can be used to monitor cache performance in an indirect way by looking at the number of Job and Build objects in each cache. Find the PID of the hudson instance and run $ jmap -histo:live <pid | grep 'hudson.model.*Lazy.*Key$' Here's a sample output: num #instances #bytes class name 523: 28 896 hudson.model.RunMap$LazyRunValue$Key 1200: 3 96 hudson.model.LazyTopLevelItem$Key These are the keys to the Jobs (LazyTopLevelItem$Key) and Builds (RunMap$LazyRunValue$Key) in the caches, so counting the number of keys is a good indicator of the number of items in the cache at any given moment. The size in bytes can be ignored, they are just the size of the keys, not the actual sizes of the objects they hold. Those sizes can only be obtained with a profiler. With the output above we can conclude that there are 3 jobs and 28 builds in memory. The 28 builds can all be from 1 job or all 3 jobs. Over time on an idle system, these should get evicted and memory cache should be empty. In practice, because of background cron threads and triggers, jobs rarely fall down to zero. Access of a job or a build by a cron thread resets the eviction timer.

  Read the article

• RHEL - blocked FC remote port time out: saving binding

  - by Dev G

  My Server went into a faulty state since the database could not write on the partition. I found out that the partition went into Read Only mode. Finally to fix it, I had to do a hard reboot. Linux 2.6.18-164.el5PAE #1 SMP Tue Aug 18 15:59:11 EDT 2009 i686 i686 i386 GNU/Linux /var/log/messages Oct 31 00:56:45 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 00:57:05 ota3g1 Had[17275]: VCS CRITICAL V-16-1-50086 CPU usage on ota3g1.mtsallstream.com is 100% Oct 31 01:01:47 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 01:06:50 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 01:11:52 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 01:12:10 ota3g1 kernel: lpfc 0000:29:00.1: 1:1305 Link Down Event x2 received Data: x2 x20 x80000 x0 x0 Oct 31 01:12:10 ota3g1 kernel: lpfc 0000:29:00.1: 1:1303 Link Up Event x3 received Data: x3 x1 x10 x1 x0 x0 0 Oct 31 01:12:12 ota3g1 kernel: lpfc 0000:29:00.1: 1:1305 Link Down Event x4 received Data: x4 x20 x80000 x0 x0 Oct 31 01:12:40 ota3g1 kernel: rport-8:0-0: blocked FC remote port time out: saving binding Oct 31 01:12:40 ota3g1 kernel: lpfc 0000:29:00.1: 1:(0):0203 Devloss timeout on WWPN 20:25:00:a0:b8:74:f5:65 NPort x0000e4 Data: x0 x7 x0 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 38617577 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283532153 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 90825 Oct 31 01:12:40 ota3g1 kernel: Aborting journal on device dm-16. Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 868841 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: Aborting journal on device dm-10. Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37759889 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283349449 Oct 31 01:12:40 ota3g1 kernel: printk: 6 messages suppressed. Oct 31 01:12:40 ota3g1 kernel: Aborting journal on device dm-12. Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-12) in ext3_reserve_inode_write: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-16, logical block 1545 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-16 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 12745 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-10, logical block 1545 Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-16) in ext3_reserve_inode_write: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-10 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37749121 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-12, logical block 0 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-12 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-12) in ext3_dirty_inode: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37757897 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-12, logical block 1097 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-12 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283337089 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-16, logical block 0 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-16 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-16) in ext3_dirty_inode: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37749121 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-12, logical block 0 Oct 31 01:12:41 ota3g1 kernel: lost page write due to I/O error on dm-12 Oct 31 01:12:41 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:41 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283337089 Oct 31 01:12:41 ota3g1 kernel: Buffer I/O error on device dm-16, logical block 0 Oct 31 01:12:41 ota3g1 kernel: lost page write due to I/O error on dm-16 Oct 31 01:12:41 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/cciss-root 4.9G 730M 3.9G 16% / /dev/mapper/cciss-home 9.7G 1.2G 8.1G 13% /home /dev/mapper/cciss-var 9.7G 494M 8.8G 6% /var /dev/mapper/cciss-usr 15G 2.6G 12G 19% /usr /dev/mapper/cciss-tmp 3.9G 153M 3.6G 5% /tmp /dev/sda1 996M 43M 902M 5% /boot tmpfs 5.9G 0 5.9G 0% /dev/shm /dev/mapper/cciss-product 25G 16G 7.4G 68% /product /dev/mapper/cciss-opt 20G 4.5G 14G 25% /opt /dev/mapper/dg_db1-vol_db1_system 18G 2.2G 15G 14% /database/OTADB/sys /dev/mapper/dg_db1-vol_db1_undo 18G 5.8G 12G 35% /database/OTADB/undo /dev/mapper/dg_db1-vol_db1_redo 8.9G 4.3G 4.2G 51% /database/OTADB/redo /dev/mapper/dg_db1-vol_db1_sgbd 8.9G 654M 7.8G 8% /database/OTADB/admin /dev/mapper/dg_db1-vol_db1_arch 98G 24G 69G 26% /database/OTADB/arch /dev/mapper/dg_db1-vol_db1_indexes 240G 14G 214G 6% /database/OTADB/index /dev/mapper/dg_db1-vol_db1_data 275G 47G 215G 18% /database/OTADB/data /dev/mapper/dg_dbrman-vol_db_rman 8.9G 351M 8.1G 5% /database/RMAN /dev/mapper/dg_app1-vol_app1 151G 113G 31G 79% /files/ota /etc/fstab /dev/cciss/root / ext3 defaults 1 1 /dev/cciss/home /home ext3 defaults 1 2 /dev/cciss/var /var ext3 defaults 1 2 /dev/cciss/usr /usr ext3 defaults 1 2 /dev/cciss/tmp /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/cciss/swap swap swap defaults 0 0 /dev/cciss/product /product ext3 defaults 1 2 /dev/cciss/opt /opt ext3 defaults 1 2 /dev/dg_db1/vol_db1_system /database/OTADB/sys ext3 defaults 1 2 /dev/dg_db1/vol_db1_undo /database/OTADB/undo ext3 defaults 1 2 /dev/dg_db1/vol_db1_redo /database/OTADB/redo ext3 defaults 1 2 /dev/dg_db1/vol_db1_sgbd /database/OTADB/admin ext3 defaults 1 2 /dev/dg_db1/vol_db1_arch /database/OTADB/arch ext3 defaults 1 2 /dev/dg_db1/vol_db1_indexes /database/OTADB/index ext3 defaults 1 2 /dev/dg_db1/vol_db1_data /database/OTADB/data ext3 defaults 1 2 /dev/dg_dbrman/vol_db_rman /database/RMAN ext3 defaults 1 2 /dev/dg_app1/vol_app1 /files/ota ext3 defaults 1 2 Thanks for all the help.

  Read the article

• "power limit notification" clobbering on 12G Dell servers with RHEL6

  - by Andrew B

  Server: Poweredge r620 OS: RHEL 6.4 Kernel: 2.6.32-358.18.1.el6.x86_64 I'm experiencing application alarms in my production environment. Critical CPU hungry processes are being starved of resources and causing a processing backlog. The problem is happening on all the 12th Generation Dell servers (r620s) in a recently deployed cluster. As near as I can tell, instances of this happening are matching up to peak CPU utilization, accompanied by massive amounts of "power limit notification" spam in dmesg. An excerpt of one of these events: Nov 7 10:15:15 someserver [.crit] CPU12: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU6: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU14: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Package power limit notification (total events = 11) Nov 7 10:15:15 someserver [.crit] CPU6: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU14: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU20: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Package power limit notification (total events = 12) Nov 7 10:15:15 someserver [.crit] CPU10: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU20: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU10: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU15: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU3: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU1: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU5: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU15: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU3: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU1: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU5: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU19: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Package power limit notification (total events = 377) Nov 7 10:15:15 someserver [.crit] CPU9: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU21: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU23: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU11: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU19: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU9: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU21: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU23: Package power limit notification (total events = 374) A little Google Fu reveals that this is typically associated with the CPU running hot, or voltage regulation kicking in. I don't think that's what is happening though. Temperature sensors for all servers in the cluster are running fine, Power Cap Policy is disabled in the iDRAC, and my System Profile is set to "Performance" on all of these servers: # omreport chassis biossetup | grep -A10 'System Profile' System Profile Settings ------------------------------------------ System Profile : Performance CPU Power Management : Maximum Performance Memory Frequency : Maximum Performance Turbo Boost : Enabled C1E : Disabled C States : Disabled Monitor/Mwait : Enabled Memory Patrol Scrub : Standard Memory Refresh Rate : 1x Memory Operating Voltage : Auto Collaborative CPU Performance Control : Disabled A Dell mailing list post describes the symptoms almost perfectly. Dell suggested that the author try using the Performance profile, but that didn't help. He ended up applying some settings in Dell's guide for configuring a server for low latency environments and one of those settings (or a combination thereof) seems to have fixed the problem. Kernel.org bug #36182 notes that power-limit interrupt debugging was enabled by default, which is causing performance degradation in scenarios where CPU voltage regulation is kicking in. A RHN KB article (RHN login required) mentions a problem impacting PE r620 and r720 servers not running the Performance profile, and recommends an update to a kernel released two weeks ago. ...Except we are running the Performance profile... Everything I can find online is running me in circles here. What's the heck is going on?

  Read the article

• Hundreds of unknown entries in Linux logwatch

  - by Saif Bechan

  I have a dedicated server which runs centos. Today i got an email from loginwatch on my server with hundreds of lines of 'errors'. I don't really know what they are becasue i am fairly new at this. The lines are in a few sections, I will display the first 10 of all of them, i hope someone can help me fix these problems. --------------------- Named Begin ------------------------ **Unmatched Entries** client 216.146.46.136 notify question section contains no SOA: 8 Time(s) client 92.114.98.10 query (cache) 'adobe.com/A/IN' denied: 4 Time(s) network unreachable resolving '11.254.75.75.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:13c7:7002:3000::11#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:13::c7d4:35#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:2e::1#53: 2 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::193#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::3#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:660:3006:1::1:1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:6b0:7::2#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:1:0:4777::140#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:2001:a:4608::59#53: 1 Time(s) network unreachable resolving '146.250.19.67.in-addr.arpa/PTR/IN': 2001:5a0:10::2#53: 1 Time(s) network unreachable resolving '149.207.106.87.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '178.62.24.195.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) this goes on for hundreds of lines with all different domain names. --------------------- pam_unix Begin ------------------------ Failed logins from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 111 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 113 times 121.14.145.32: 136 times 190.152.69.5: 248 times 209.160.72.15: 572 times 210.26.48.35: 2 times 212.235.111.224 (DSL212-235-111-224.bb.netvision.net.il): 140 times 218.206.25.29: 140 times Illegal users from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 2665 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 2539 times 121.14.145.32: 116 times 190.152.69.5: 34 times 209.160.72.15: 324 times 218.206.25.29: 8051 times proftpd: Unknown Entries: session opened for user cent_ftp by (uid=0): 15 Time(s) session closed for user cent_ftp: 14 Time(s) sshd: Authentication Failures: unknown (218.206.25.29): 8051 Time(s) unknown (78-86-126-211.zone2.bethere.co.uk): 2665 Time(s) unknown (93.97.176.136): 2539 Time(s) root (209.160.72.15): 558 Time(s) unknown (209.160.72.15): 324 Time(s) root (190.152.69.5): 246 Time(s) unknown (121.14.145.32): 116 Time(s) root (121.14.145.32): 106 Time(s) root (dsl212-235-111-224.bb.netvision.net.il): 70 Time(s) root (93.97.176.136): 44 Time(s) root (78-86-126-211.zone2.bethere.co.uk): 37 Time(s) unknown (190.152.69.5): 34 Time(s) mysql (121.14.145.32): 30 Time(s) nobody (218.206.25.29): 26 Time(s) mail (218.206.25.29): 24 Time(s) news (218.206.25.29): 24 Time(s) root (218.206.25.29): 24 Time(s) --------------------- SSHD Begin ------------------------ **Unmatched Entries** pam_succeed_if(sshd:auth): error retrieving information about user tavi : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pam : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user konchog : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user stavrum : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user rachel : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user affiliates : 24 time(s) pam_succeed_if(sshd:auth): error retrieving information about user nen : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cobra : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pass : 7 time(s) pam_succeed_if(sshd:auth): error retrieving information about user hacer : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user chung : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user zainee : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user radu : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user alka : 4 time(s) pam_succeed_if(sshd:auth): error retrieving information about user albert : 5 time(s) pam_succeed_if(sshd:auth): error retrieving information about user turcia : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cordell : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user silver : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user dragon : 3 time(s) If someone wants to see the whole log i can upload it somewhere. Am i being hacked, what is this all?? I hope someone can help me, this does not look good at all.

  Read the article

• NetBackup with VSS and Instant Recovery - Failing to delete old snapshots

  - by Jonathan Bourke

  We are attempting to implement Microsoft VSS for snap-shotting in our NetBackup 6.5.3.1 environment. The clients are both 32 & 64 bit Windows 2003 Server. Snapshot parameters are: Instant recovery is enabled Maximum snapshots = 1 Provider type = 1 (System) Snapshot attribute = 1 (Differential) All backups successfully complete, and VSS shadows are successfully created both for the snapshot backup and for the open files (shadow copy components). The Issue: NetBackup is not clearing or overwriting old snapshots with each successive backup. When we list shadows, and shadow storage, it is increasing and increasing. IT is not honouring the Maximum Snapshot setting. The Logs: The bpfis log doesn’t really appear to show any errors other than for methods which we are not employing (VxVM, Flashsnap, etc.). A section is as follows: 11:54:10.744 [348.4724] <2> logparams: D:\Program Files\Veritas\NetBackup\bin\bpfis.exe delete -nbu -id htpststr001.san.mgmt.det_1248918143 -bpstart_to 300 -bpend_to 300 -clnt htpststr001.san.mgmt.det 11:54:10.744 [348.4724] <4> bpfis: INF - BACKUP START 348 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS error 10; see following messages: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: Non-fatal method error was reported 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: vfm_configure_fi_one: method: FlashSnap, type: FIM, function: FlashSnap_init 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS method error 3; see following message: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: FlashSnap_init: Veritas Volume Manager not installed. 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS error 10; see following messages: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: Non-fatal method error was reported 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: vfm_configure_fi_one: method: vxvm, type: FIM, function: vxvm_init 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS method error 3; see following message: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: vxvm_init: Veritas Volume Manager not installed. 11:54:11.713 [348.4724] <4> onlfi_thaw: Thawing C:\ using snapshot method VSS. 11:54:11.713 [348.4724] <2> onlfi_vfms_logf: vfm_thaw: delete snapshot ... 11:54:11.744 [348.4724] <2> onlfi_vfms_logf: snapshot services: emcclariionfi:Thu Jul 30 2009 11:54:11.744000 <Thread id - 4724> Unable to import any login credentials for any appliances. 11:54:11.760 [348.4724] <2> onlfi_vfms_logf: snapshot services: hpevafi:Thu Jul 30 2009 11:54:11.760000 <Thread id - 4724> CHpEvaPlugin::init: CLI tool is not installed. 11:54:11.760 [348.4724] <2> onlfi_vfms_logf: snapshot services: hpmsafi:Thu Jul 30 2009 11:54:11.760000 <Thread id - 4724> No array mangement credentials are available in configuration file. 11:54:13.806 [348.4724] <4> onlfi_thaw: do_thaw return value: 0 11:54:13.806 [348.4724] <4> onlfi_thaw: Thawing D:\ using snapshot method VSS. 11:54:15.806 [348.4724] <4> onlfi_thaw: do_thaw return value: 0 11:54:19.806 [348.4724] <2> fis_delete_id: removing D:\Program Files\Veritas\NetBackup\online_util\fi_cntl\bpfis.fim.htpststr001.san.mgmt.det_1248918143.0 11:54:19.806 [348.4724] <2> fis_delete_id: removing D:\Program Files\Veritas\NetBackup\online_util\fi_cntl\bpfis.fim.htpststr001.san.mgmt.det_1248918143.0.fiid 11:54:19.853 [348.4724] <4> bpfis: INF - EXIT STATUS 0: the requested operation was successfully completed The Question: Has anyone any experience of NetBackup / VSS not clearing snapshots after backups? We will ultimately be using a HP EVA for the snapshots, but we want to ensure correct functioning at a VSS level before we go further. Regards, Jonathan (PS: Question previously posted by my colleague on entsupport.symantec.com)

  Read the article

• Play music on iPhone through computer

  - by Kyle Cronin

  Now that I've had my iPhone for a few months, I'm trying an experiment to see if I can't replace the laptop I carry around with my iPhone + internet connected computer. To this end, I've been trying to find a program that will let me play the music on my iPhone through the hardware and software on the host computer. If I recall correctly this was possible a few years ago with the iPod - Linux software like Rhythmbox and Banshee was able to read the music off an iPod and play it through the speakers. I even thought I recalled iTunes itself being capable of this at one time. Now, however, iTunes greys out/disables the music on my iPhone and I can't find any documented support for the iPhone in any other music program. Is this really no longer possible? Am I limited to using the headphone jack to get music to play? (note: I am using an iPhone 3G with the 3.0 software. I am attempting to play music on computers other than the one I sync with) Several replies mention that I should check "manually manage" to do this. I just tried this on a computer that I don't sync my iPhone to and it asked me to erase and sync, which is obviously something I don't want to do. update: OK, I checked the "Manually manage music and videos" box on a computer that I didn't sync to (now known as "Computer A"), and it told me that I needed to erase & sync to cause the changes to have effect, so I did. At this point I'm guessing that my iPhone thinks that it's syncing with that computer. I copied over a few songs using the autofill feature. At this point, Computer A sees the maybe 10 or so songs I've copied using autofill. I then plug my iPhone into my Macbook ("Computer B") which I've been syncing with. At this point, I'm pretty sure that it still thought that all my synced content was still on my iPhone. The "manually manage music and videos" checkbox isn't checked, so I check it and go through a similar process where iTunes erases the synced content and I copy over a playlist. At this point, there's no trace of the songs that I copied over from Computer A. So I plug my iPhone into Computer A - in the Music section are the handful of songs that I had copied over earlier, greyed out and unplayable. To make sure that this wasn't some sort of caching issue, I plugged my iPhone into my sister's Macbook ("Computer C") and it lists the same few, greyed out songs that I had copied over from Computer A. Plugging into Computer B doesn't reveal these songs at all, only the songs that it copied over (these are playable). A few things: This inconsistent behavior is driving me insane. Why would my iPhone report two versions of its contents to different computers? Is there a way to get a computer to completely forget about an iPhone and just resync everything to get everything into a consistent state? Even if I get the phone into a consistent state, I still can't play the files on my phone anywhere but the computer I sync with, which was my original goal. What am I doing wrong? maybe I should read the fine print before I mess with my iPhone So going over this thread with a fine-toothed comb again yields this lovely tidbit in the Apple docs: Note: Even when manually managing, some content may only be available from one library at time. This includes all content on iPhone and video content on iPods. OK, so manually managing is a dead end on the iPhone. Are there any other options? Any unofficial third-party programs or drivers that will work?

  Read the article

• Windows: what is the difference between DEP always on and DEP opt-out with no exceptions?

  - by Peter Mortensen

  What is the difference between DEP always on ("/NoExecute=AlwaysOn" in boot.ini) and DEP opt-out ( "/NoExecute=OptOut" in boot.ini) with no exceptions? "no exceptions" = empty list of programs for which DEP does not apply. DEP = Data Execution Prevention (hardware). One would expect it to work the same way, but it makes a difference for some applications. E.g. for all versions of UltraEdit 14 (14.2). It crashes at startup for DEP always on, at least on Microsoft Windows XP Professional Edition x64 edition. (2010-03-11: this problem has been fixed with UltraEdit 15.2 and later.) Update 1: I think this difference is caused by the backdoors that Microsoft has put into hardware DEP for OptOut, according to Fabrice Roux (see below). In the case of IrfanView, for which Steve Gibson observed the same difference as I did for UltraEdit (see below), the difference is caused by a non-DEP aware EXE packer (ASPack) that Microsoft coded a backdoor for. Is there a difference between Windows XP, Windows Vista and Windows 7 ? Is there a difference between 32 bit and 64 bit versions of Windows ? Sources: From [http://blog.fabriceroux.com/index.php/2007/02/26/hardware_dep_has_a_backdoor?blog=1], "Hardware DEP has a backdoor" by Fabrice Roux. 2007-02-26. "IrfanView was not using any trick to evade DEP ... Microsoft just coded a backdoor used only in OPTOUT. Bascially Microsoft checks the executable header for a section matching one of the 3 strings. If one these strings is found, DEP will be turned OFF for this application by windows. ... 'aspack', 'pcle', 'sforce'" From [http://www.grc.com/sn/sn-078.htm], by Steve Gibson. "I can’t find any documentation on Microsoft’s site anywhere, because we’re seeing a difference between always-on and opt-out. That is, you would imagine that always-on mode would be the same as opting out if you weren’t having any opt-out programs. It turns out it’s not the case. For example ... the IrfanView file viewer ... runs fine in opt-out mode, even if it has not been opted out. But it won’t launch, Windows blocks it from launching ... in always-on mode." From [http://www.grc.com/sn/sn-083.htm], by Steve Gibson. "... IrfanView ... won’t run with DEP turned on. It’s because it uses an EXE packer, an executable compression program called ASPack. And it makes sense that it wouldn’t because naturally an executable compressor has got to decompress the executable, so it allocates a bunch of data memory into which it decompresses the compressed executable, and then it runs it. Well, it’s running a data allocation, which is exactly what DEP is designed to stop. On the other hand, UPX, which is actually the leading and most popular EXE compressor, it’s DEP- compatible because those guys realized, hey, when we allocate this memory, we should mark the pages as executable."

  Read the article

• Hyper-V File Server Clustering - at my wit’s end

  - by René Kåbis

  I am at my wit’s end with File Server clustering under Hyper-V. I am hoping that someone might be able to help me figure out this Gordian Knot of a technology that seems to have dead ends (like forcing cluster VMs to use iSCSI drives where normally-attached VHDX drives could suffice) where logic and reason would normally provide a logical solution. My hardware: I will be running three servers (in the end), but right now everything is taking place on one server. One of the secondary servers will exist purely as a witness/quorum, and another slightly more powerful one will be acting as an emergency backup (with additional storage, just not redundant) to hold the secondary AD VM and the other halves of a set of clustered VMs: the SQL VM and the file system VM. Please note, these each are the depreciated nodes of a cluster, the main nodes will be on the most powerful first machine. My heavy lifter is a machine that also contains all of the truly redundant storage on the network. If this gives anyone the heebie-geebies, too bad. It has a 6TB (usable) RAID-10 array, and will (in the end) hold the primary nodes of both aforementioned clusters, but is right now holding all VMs. This is, right now: DC01, DC02, SQL01, SQL02, FS01 & FS02. Eventually, I will be adding additional VMs to handle Exchange, Sharepoint and Lync, but only to this main server (the secondary server won't be able to handle more than three or four VMs, so why burden it? The AD, SQL & FS VMs are the most critical for the business). If anyone is now saying, “wait, what about a SAN or a NAS for the file servers?”, well too bad. What exists on the main machine is what I have to deal with. I followed these instructions, but I seem to be unable to get things to work. In order to make the file server truly redundant, I cannot trust any one machine to hold the only data store on the network. Therefore, I have created a set of iSCSI drives on the VM-host of the main machine, and attached one to each file server VM. The end result is that I want my FS01 to sit on the heavy lifter, along with its iSCSI “drive”, and FS02 will sit on the secondary machine with its own iSCSI “drive” there as well. That is, neither iSCSI drive will end up sitting on the same machine as the other. As such, the clustered FS will utterly duplicate the contents of the iSCSI drives between each other, so that if one physical machine (or the FS VM) goes toes-up, the other has got a full copy of the data on its own iSCSI drive. My problem occurs when I try to apply the file server role within the failover cluster manager. Actually, it is even before that -- it occurs when adding the disks. Since I have added each disk preferentially to a specific VM (by limiting the initiator by DNS hostname, and by adding two-way CHAP authentication), this forces each VM to be in control of its own iSCSI disk. However, when I try to add the disks to the Disks section of Storage within Failover Cluster Manager, the entire process fails for a random disk of the pair. That is, one will get online, but the other will remain offline because it does not have the correct “owner node”. I mean, really -- WTF? Of course it doesn’t have the right owner node, both drives are showing the same node name!! I cannot seem to have one drive show up with one node name as owner, and the other drive show up with the other node name as owner. And because both drives are not “online”, I cannot create a pool to apply to a cluster role. Talk about getting stuck between a rock and a hard place! I’ve got more to add, but my work is closing for the day and I have to wrap things up. I will try to add more tomorrow morning when I get in. My main objective is to have a file server VM on each machine, the storage on each machine, but a transparent failover in case one physical machine fails. Essentially, a failover FS that doesn’t care which machine fails -- the storage contents are replicated equally on each machine. Am I even heading in the right direction?

  Read the article

• Does likewise-open > version 5.4 contain CIFS support?

  - by Ben Andken

  I'm trying to get the CIFS server working in likewise-open. I've found this set of instructions and everything seems to work until I try to connect ([url]http://www.likewise.com/resources/documentation_library/manuals/cifs/likewise-cifs-smb-file-server-guide.html#id2765992):[/url] 1.6. Build and Configure a Standalone Likewise-CIFS Server This section demonstrates how to build and configure a standalone instance of Likewise-CIFS from the command line. The following procedure assumes that you want to set up Likewise-CIFS on a Linux server to share files with Windows computers in a network without Active Directory. This procedure also assumes you know how to build Linux applications from their source code and then install them. Download Likewise-CIFS from its open source git location: $ git clone git://git.likewiseopen.org/ Download, build, and install the following tools. The tools listed are known to work, but earlier or later versions might work as well. Also, instead of downloading the tools, you might be able to install them on your platform with apt-get or some other means. http://ftp.gnu.org/gnu/autoconf/autoconf-2.65.tar.gz http://ftp.gnu.org/gnu/automake/automake-1.9.6.tar.gz http://ftp.gnu.org/gnu/libtool/libtool-2.2.6a.tar.gz http://pkgconfig.freedesktop.org/releases/pkg-config-0.23.tar.gz gcc --version 3.x or greater Build Likewise-CIFS: $ cd likewise-open $ build/mkcomp --debug all Install Likewise-CIFS: $ sudo su $ cd staging/install-root $ tar cf - . | (cd / && tar xvf -) Make sure Samba is not running: $ /etc/init.d/smb stop Make sure SELinux is either disabled or set to permissive. Make sure the ports required by Likewise are open. For a list of ports that Likewise uses, see the Likewise Open Installation and Administration Guide. Configure Likewise Open: $ /etc/init.d/lwsmd start $ for i in /etc/likewise/*.reg; do /opt/likewise/bin/lwregshell upgrade $i; done $ /etc/init.d/lwsmd stop $ /etc/init.d/lwsmd start $ /opt/likewise/bin/lwsm start srvsvc $ /opt/likewise/bin/domainjoin-cli configure --enable nsswitch Add a user account to the local Likewise provider database. In the following example, substitute the account name that you want for newuser. $ /opt/likewise/bin/lw-add-user --home /home/newuser --shell /bin/bash newuser Successfully added user newuser Enable the user and set the password: $ /opt/likewise/bin/lw-mod-user --enable-user --set-password newuser New Password: ********** Successfully modified user newuser Look up new user's identity as follows. Substitute the value from the command hostname -s for the hostname. Keep in mind that Likewise truncates a hostname longer than 15 characters to the first 15 characters of the string. % id hostname\\newuser uid=2000(HOSTNAME\newuser) gid=1800(HOSTNAME\Likewise Users) groups=1800(HOSTNAME\Likewise Users) context=system_u:system_r:unconfined_t:s0 Make a CIFS directory for the user: mkdir /lwcifs/newuser chown 2000:1800 /lwcifs/newuser From a Windows computer, map the Likewise-CIFS drive share: Computer->Map Network Drive... Folder: \\IP_hostname\c$ Click "Finish" Username: hostname\newuser Password: user_password The last step fails when I try to connect. I've tried with Windows XP Pro and Windows 7 Pro. The rest of the directions only appear to work for version 5.4 (the one that shipped with 10.04). For 12.04, version 6.1 is the only one available and it doesn't appear to have the srvsvc module mentioned in these instructions. Is CIFS support dropped in the 6.1 version of likewise-open?

  Read the article

• Redmine with Apache 2 + Passenger nightmare --- site is up and available, but Redmine doesn't execute

  - by CptSupermrkt

  I was determined to figure this out myself, but I've been at it for a total of more than 10 hours, and I just can't figure this out. First, let me detail my environment (which I cannot change): Server version: Apache/2.2.15 (Unix) Ruby version: ruby 1.9.3p448 Rails version: Rails 4.0.1 Passenger version: Phusion Passenger version 4.0.5 Redmine version: 2.3.3 I have followed the Redmine instructions all the way through the test webserver to check that installation was successful with this command: ruby script/rails server webrick -e production The roadblock which I cannot overcome is getting Apache and Passenger to interpret and properly serve Redmine. I have searched pretty much every possible link within the first 10 pages or so of Google results. Everywhere I go I come across conflicting/contradicting/outdated information. We have a "weird" setup with Apache (which I inherited and cannot change). Redmine needs to be served through SSL, but Apache already has another website it's serving through SSL called Twiki. By "weird", what I mean is that our file structure is entirely different from all the tutorials out there on this version of Apache which have directories like "available-sites" and such. Here are the abbreviated versions of some of our config files: /etc/httpd/conf/httpd.conf (the global configuration file --- note that NO VirtualHost is defined here): ServerRoot "/etc/httpd" ... LoadModule passenger_module /usr/local/pkg/ruby/1.9.3-p448/lib/ruby/gems/1.9.1/gems/passenger-4.0.5/libout/apache2/mod_passenger.so PassengerRoot /usr/local/pkg/ruby/1.9.3-p448/lib/ruby/gems/1.9.1/gems/passenger-4.0.5 PassengerDefaultRuby /usr/local/pkg/ruby/1.9.3-p448/bin/ruby Include conf.d/*.conf ... User apache Group apache ... DocumentRoot "/var/www/html" So just to clarify, the above httpd.conf file does NOT have a VirtualHost section. /etc/httpd/conf.d/ssl.conf (defines the VirtualHost for ssl): Listen 443 <VirtualHost _default_:443> SSLEngine on ... SSLCertificateFile /etc/pki/tls/certs/localhost.crt </VirtualHost> /etc/httpd/conf.d/twiki.conf (this works just fine --- note this does NOT define a VirtualHost): ScriptAlias /twiki/bin/ "/var/www/twiki/bin/" Alias /twiki/ "/var/www/twiki/" <Directory "/var/www/twiki/bin"> AllowOverride None Order Deny,Allow Deny from all AuthType Basic AuthName "our team" AuthBasicProvider ldap ...a lot of ldap and authorization stuff Options ExecCGI FollowSymLinks SetHandler cgi-script </Directory> /etc/httpd/conf.d/redmine.conf: Alias /redmine/ "/var/www/redmine/public/" <Directory "/var/www/redmine/public"> Options Indexes ExecCGI FollowSymLinks Order allow,deny Allow from all AllowOverride all </Directory> The amazing thing is that this doesn't completely NOT work: I can successfully open up https://someserver/redmine/ with SSL and the https://someserver/twiki/ site remains unaffected. This tells me that it IS possible to have two separate sites up with one SSL configuration, so I don't think that's the problem. The problem is is that it opens up to the file index. I can navigate around my Redmine file structure, but no code ever gets executed. For example, there is a file included with Redmine called dispatch.fcgi in the public folder. https://someserver/redmine/dispatch.fcgi opens, but just as plain text code in the browser. As I understand it, in the case of using Passenger, CGI and FastCGI stuff is irrelevant/unused.

  Read the article

• Apache logs 200 instead of 404

  - by elle

  I've been getting the following in my apache access log: "GET /work//?module=www&section=working=../../../../../../../../../../../../../../../../../../../../../../../..//proc/self/environ%0000 HTTP/1.1" 200 5187 "-" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.2.12) Gecko/20101026 Firefox/3.6.12\",\"Mozilla/5.0 (Windows; U; Windows NT 5.1; pl-PL; rv:1.8.1.24pre) Gecko/20100228 K-Meleon/1.5.4\",\"Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/540.0 (KHTML,like Gecko) Chrome/9.1.0.0 Safari/540.0\",\"Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US) AppleWebKit/532.5 (KHTML, like Gecko) Comodo_Dragon/4.1.1.11 Chrome/4.1.249.1042 Safari/532.5\",\"Mozilla/5.0 (X11; U; Linux i686 (x86_64); en-US; rv:1.9.0.16) Gecko/2009122206 Firefox/3.0.16 Flock/2.5.6\",\"Mozilla/5.0 (Windows; U; Windows NT 6.0; en-US) AppleWebKit/533.1 (KHTML, like Gecko) Maxthon/3.0.8.2 Safari/533.1\",\"Mozilla/5.0 (Windows; U; Windows NT 6.0; en-US; rv:1.8.1.8pre) Gecko/20070928 Firefox/2.0.0.7 Navigator/9.0RC1\",\"Opera/9.99 (Windows NT 5.1; U; pl) Presto/9.9.9\",\"Mozilla/5.0 (Windows; U; Windows NT 6.1; zh-HK) AppleWebKit/533.18.1 (KHTML, like Gecko) Version/5.0.2 Safari/533.18.5\",\"Seamonkey-1.1.13-1(X11; U; GNU Fedora fc 10) Gecko/20081112\",\"Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; Win64; x64; Trident/5.0; .NET CLR 2.0.50727; SLCC2; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; Zune 4.0; Tablet PC 2.0; InfoPath.3; .NET4.0C; .NET4.0E)\",\"Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; MS-RTC LM 8; .NET4.0C; .NET4.0E; InfoPath.3)" If I try the URL, I get a 404 instead of 200 which the above request received. Is there a way I can confirm that the 200 was real and not spoofed? Where is the long info on the client coming from?

  Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >