Search Results

Search found 10536 results on 422 pages for 'dan course'.

Page 299/422 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >

• ZFS with L2ARC (SSD) slower for random seeks than without L2ARC

  - by Florian Kruse

  I am currently testing ZFS (Opensolaris 2009.06) in an older fileserver to evaluate its use for our needs. Our current setup is as follows: Dual core (2,4 GHz) with 4 GB RAM 3x SATA controller with 11 HDDs (250 GB) and one SSD (OCZ Vertex 2 100 GB) We want to evaluate the use of a L2ARC, so the current ZPOOL is: $ zpool status pool: tank state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM afstank ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c11t0d0 ONLINE 0 0 0 c11t1d0 ONLINE 0 0 0 c11t2d0 ONLINE 0 0 0 c11t3d0 ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c13t0d0 ONLINE 0 0 0 c13t1d0 ONLINE 0 0 0 c13t2d0 ONLINE 0 0 0 c13t3d0 ONLINE 0 0 0 cache c14t3d0 ONLINE 0 0 0 where c14t3d0 is the SSD (of course). We run IO tests with bonnie++ 1.03d, size is set to 200 GB (-s 200g) so that the test sample will never be completely in ARC/L2ARC. The results without SSD are (average values over several runs which show no differences) write_chr write_blk rewrite read_chr read_blk random seeks 101.998 kB/s 214.258 kB/s 96.673 kB/s 77.702 kB/s 254.695 kB/s 900 /s With SSD it becomes interesting. My assumption was that the results should be in worst case at least the same. While write/read/rewrite rates are not different, the random seek rate differs significantly between individual bonnie++ runs (between 188 /s and 1333 /s so far), average is 548 +- 200 /s, so below the value w/o SSD. So, my questions are mainly: Why do the random seek rates differ so much? If the seeks are really random, they should not differ much (my assumption). So, even if the SSD is impairing the performance it should be the same in each bonnie++ run. Why is the random seek performance worse in most of the bonnie++ runs? I would assume that some part of the bonnie++ data is in the L2ARC and random seeks on this data performs better while random seeks on other data just performs similarly like before.

  Read the article

• Can you transfer a Windows 7 XP-mode VHD to a new PC without the need for reactivation?

  - by Henk

  Hi. At the moment I am running Vista 32 bit and use VPC 2007 a lot. I have several W2000 VMs set up with complex software configurations. For me, one of the advantages of working with VPCs is that a VM can easily be copied to another PC (like a notebook). Also, when I move to a new PC, I can immediately work with my existing VMs without the need to reinstall all applications. I am thinking about buying a new pc with Windows 7 64 bit pro, and using the xp-mode VM that comes with Windows 7. The advantages would be support for more memory (so being able to run more VM's simultaneously) and having a licenced XP VM. I would like to know if you can transfer a VHD that is based on the xp-mode VHD to another machine without Activation issues. The other machine will of course, also be running W7. I would guess that this would not be a problem. However, I did read about a guy who had to reinstall his W7 because of a harddisk failure, and could not access his xp-mode VHD anymore because it demanded re-activation. Thanks. Henk.

  Read the article

• Have it fixed or buy a new one?

  - by Workshop Alex

  My dual-monitor system has just become a single-monitor system again when the older monitor decided it would be nice to just turn to black. It's a Samsung LCD monitor and is over three years old. Not sure if the warranty is still valid but I just wonder what option would me more efficient: 1) Have the monitor fixed for a small amount. 2) Buy a new monitor for a slightly bigger amount. When monitors were still expensive, I wouldn't doubt about this and would just have my monitor repaired. But prices are so low nowadays, (and repairs are expensive) that I wonder if it's worth the trouble... Of course, I'm in no hurry since I still have another monitor. It's just that I liked the dual-monitor setup. Solved! Just ordered a new monitor. A Samsumg Syncmaster T260HD 25,5". Much more than it would cost me if I just had my old one repaired but I noticed that this one has a build-in TV tuner, plus speakers. It's way more expensive than a repair, but it's worth the additional value it provides.

  Read the article

• Can I get all active directory passwords in clear text using reversible encryption?

  - by christian123

  EDIT: Can anybody actually answer the question? Thanks, I don't need no audit trail, I WILL know all the passwords and users can't change them and I will continue to do so. This is not for hacking! We recently migrated away from a old and rusty Linux/Samba domain to an active directory. We had a custom little interface to manage accounts there. It always stored the passwords of all users and all service accounts in cleartext in a secure location (Of course, many of you will certainly not think of this a being secure, but without real exploits nobody could read that) and disabled password changing on the samba domain controller. In addition, no user can ever select his own passwords, we create them using pwgen. We don't change them every 40 days or so, but only every 2 years to reward employees for really learning them and NOT writing them down. We need the passwords to e.g. go into user accounts and modify settings that are too complicated for group policies or to help users. These might certainly be controversial policies, but I want to continue them on AD. Now I save new accounts and their PWGEN-generated (pwgen creates nice sounding random words with nice amounts of vowels, consonants and numbers) manually into the old text-file that the old scripts used to maintain automatically. How can I get this functionality back in AD? I see that there is "reversible encryption" in AD accounts, probably for challenge response authentication systems that need the cleartext password stored on the server. Is there a script that displays all these passwords? That would be great. (Again: I trust my DC not to be compromised.) Or can I have a plugin into AD users&computers that gets a notification of every new password and stores it into a file? On clients that is possible with GINA-dlls, they can get notified about passwords and get the cleartext.

  Read the article

• systemd: enabling cherokee service as a `unit file`

  - by Calvin Cheng

  So I am learning how to use systemd to initialize my services automatically on server reboot. So of course, I first make sure I have systemd and some optional systemd related packages installed. pacman -S systemd initscripts-systemd Installation seems to go well and checking, I can see that systemd and its dependency libsystemd are installed. And the optional package initscripts-systemd is also installed:- [root@li280-195 ~]# pacman -Ss systemd extra/libsystemd 44-5 [installed] systemd client libraries extra/systemd 44-5 [installed] system and service manager extra/systemd-sysvcompat 2-2 sysvinit compat symlinks for systemd community/initscripts-systemd 20120412-1 [installed] Arch specific systemd initialization/bootup scripts for systemd community/systemd-arch-units 20120412-2 Arch specific Systemd unit files Next, I ensure that systemd is loaded up when my server reboots, via grub in grub's /boot/grub/menu.lst file like this:- kernel /boot/vmlinuz root=/dev/xvda ro init=/bin/systemd Rebooting my server to check, all loads up well and I can check that systemd is operational via:- systemctl list-unit-files However, I don't see my cherokee initialization script (which is simply created at /etc/rc.d/cherokee when I installed cherokee earlier via pacman -S cherokee) being listed as one of my unit files. So the question is, how do I do that? How do I put my cherokee initialization script under systemd's control?

  Read the article

• Uploading file > 1 MB on Django admin gives 400 Bad Request response.

  - by ayaz

  I have a small Django (1.2.x) project deployed on Apache (2.x) via mod_wsgi (2.x). In the admin, if I upload a file < 1MB, I can get it through; however, for a file, say, 1.2MB in size, I get a 400 response from the server with "Error 400" in the body only. I am wondering why this is happening. As far as I can see, there is no LimitRequestBody set in Apache configuration. I have tried uploading with several browsers including: Firefox, Chrome, and Safari. In the log file for Apache, there is apparently no entry for requests that gave the 400 error response. This is strange. I should point out that the scenario where this is happening is thus: The project in question is deployed on two identical Apache servers (completely identical setup) that are behind a load balancer. On my development setup, of course, the problem does not surface. Any help with this will be very much appreciated.

  Read the article

• Set postfix to send email but not to receive them

  - by CodeShining

  I'm using Google Apps to handle personal email addresses for my domain name, and I set up the DNS as Google suggests. All works fine. Now since I need a SMTP to send emails from my e-commerce I installed Postfix on the server. It works fine when I send emails to any email address but it doesn't send to the same domain name, so let's say my domain is example.com, I set postfix using example.com, if I try to reset a password using [email protected] postfix doesn't send and instead reports on the mail.log Sep 20 01:09:52 ip-10-54-26-162 postfix/pickup[6809]: B09A3415D8: uid=33 from=<www-data> Sep 20 01:09:52 ip-10-54-26-162 postfix/cleanup[6854]: B09A3415D8: message-id=<20120920010952.B09A3415D8@ip-10-54-26-162.eu-west-1.compute.internal> Sep 20 01:09:52 ip-10-54-26-162 postfix/qmgr[30978]: B09A3415D8: from=<[email protected]>, size=4234, nrcpt=1 (queue active) Sep 20 01:09:52 ip-10-54-26-162 postfix/local[6856]: B09A3415D8: to=<[email protected]>, relay=local, delay=0.01, delays=0.01/0/0/0, dsn=5.1.1, status=bounced (unknown user: "myaccount") Of course it cannot find a local user "myaccount" since that account is on Google Apps... How can I tell Postfix to send the email and do not search for a local user?

  Read the article

• master-slave datastore replication, automatic failover, and wackamole

  - by z8000

  I have 2 dedicated servers provisioned for my next project's datastores. The datastores are configured for master-slave replication. There's no inherent automatic failover but I of course want this. That is, I'd love for access to the master datastore to always just work without having to configure a client library to detect when a master is down and failover to the slave. I've seen Wackamole which is based on the Spread Toolkit. You provide Wackamole with a set of IPs and a bunch of nodes, and regardless of the up/down state of any of the nodes, those IPs will stay available/up. Wackamole detects when a node goes down and ARPs the IP(s) that were up on the now-down node. It's pretty neat actually. So, my thought was to use Wackamole to keep the 2 virtual private IPs available/up. Clients would then just always use the same private IP to access the master datastore and the same but distinct IP for the slave datastore, even if those IPs were hosted on the same node. My datastore servers are accessed over a private network. I am unsure if this messes with Wackamole though. Is this lunacy? How do you generally handle automatic failover of private services like a datastore. FWIW, it shouldn't matter but the datastore is Redis. I don't want to hear "use mySQL" please :) Thanks.

  Read the article

• Cannot start Postgres daemon after installing with Yum

  - by Sean the Bean

  I was trying to install Postgres 9.1.4 on Fedora 17 using Yum. If I do: sudo yum install postgres-libs sudo yum install postgres sudo yum install postgis All the installs appear to complete successfully (i.e., no errors), but I cannot start the Postgres daemon using: service postgresql initdb Like the official Postgres download guide says to do (http://www.postgresql.org/download/linux/redhat/). The error says Unknown operation initdb. RPM tells me that it installed psql to /usr/bin/, which I confirmed. It turns out that only a few components installed correctly (psql, pg_dump, pg_configure, and a few others), but most are missing (e.g., pg_ctl and postgres). I've tried several different configurations and had several of my coworkers (with more linux experience than me) look at it, but so far nothing has worked. Two of them have also run into similar issues installing Postgres using apt-get on Ubuntu, which makes me think the rpm isn't doing its job. It seems the only solution to build it from source, which is more robust anyway, but of course it takes longer. I'm wondering, though, if anyone else has run into this issue and/or has successfully installed Postgres on either Fedora or Ubuntu using a package manager like yum or apt-get? Is the rpm broken?

  Read the article

• Windows XP Boot Issue - Diagnosing A Hard Drive Failure

  - by duffymo

  My five-year-old HP desktop running Windows XP SP3 wouldn't boot from the hard drive yesterday afternoon. I would see the boot sequence begin, then nothing but a black screen. Fortunately, I had just done an Acronis backup to my external drive in the morning, and I have a bootable USB key. I put the USB key into the drive, powered up the machine, and put the USB key first in line in the boot sequence. Voila! My machine came alive. But now I'm confused as to what the problem is and what to do next. I assumed that my hard drive was toast. But now that the machine is alive I can see files on my C: drive that have changes I made just yesterday. Clearly the drive is not dead. Here are my questions: What could explain my inability to boot from the hard drive? What would a remedy be? What's my best course of action? Should I replace the hard drive with a new one? If I replace the hard drive, do I reinstall the OS and apply the backup I did yesterday? If I decide that re-installing Windows XP makes no sense, how do I get back the Acronis backup that I did yesterday? I don't want to lose that. UPDATE: I just learned one more key fact. I'm having some work done on my house. I neglected to shut my machine down before the contractor came. My wife said he shut down the power to do some work on a circuit and then powered the house back up. I have a surge protector, but is it possible that cycling the power did some damage?

  Read the article

• How does one make sure or even guarantee server time are sync correctly between dozens of servers across multiple datacenter on different location?

  - by forestclown

  Currently our web applications contain a logic to check if the data sent to the web server is expired or not by comparing the timestamp of the data with the date/time of the server. Everything goes will, until some dude from data center accidentally modify one of the web server date/time and causes some disruptions in our web services. My managers are of course not happy with this, and said we shouldn't use timestamp to check expiry in the first place...anyway.... Network Time Protocol is implemented, because of data centers are spread across different continents so we have one NTP server in each data center. The servers within the data center will have cron jobs to check against the time with their NTP server from the same data center. If time is out of sync it will auto update the server date/time. But then with our managers not happy with it, and think it could still easily causes the same problem. e.g. what if someone accidentally modify the NTP date/time? what if all the NTP servers are out of sync with each other? which NTP servers we can really trust? and blah blah.. So my questions are: What are the current practice to sync date/time between servers across multiple data centers or locations? How does one manages time stamp between web apps? e.g. Server A send data (contain timestamp of Server A) to Server B (compare timestamp between Server B and the timestamp from the data to see if it has expired or not. This is to avoid HTTP replay) Should we really not use timestamp check? Thanks & Best Regards

  Read the article

• How private is the Opera Turbo feature of Opera?

  - by Marcus V

  If I'm using Opera with the Opera Turbo feature turned on (always, not set to "automaticly"). Can anyone see what sites I'm visiting (except Opera of course ...)? Opera Turbo uses a proxy server, so it should be that way, but as a not very technical person I'm not sure. Why do I want this? Well: nowadays, at least in my country, more and more (legal) open Wi-Fi connections are available. In those environments I like to have more privacy protections. I don't mind if they can see my IP address, but I just want to hide as much as I can of what I am doing. BTW: I don't care that they can see the data transferred; it doesn't have to be that secret. I only want to hide the requested Internet site links. BTW: I know that Opera Turbo only works with non-secure websites (HTTP), but that's fine for me. I only want it to work with these sites. BTW: I'm not need this for illegal purposes; I only want this for privacy reasons.

  Read the article

• Trouble getting latest version of Git

  - by TheMethod

  I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

  Read the article

• Affordable combined Ruby/Rails/Redmine + Subversion hosting?

  - by Pekka

  I'm a self employed web developer and after nine years of hard work, I'm looking to become a bit more "vagrant" starting next year, do some much-needed traveling and a bit and work off and on, making use of one of the greatest advantages of a programming job: The ability to work virtually from everywhere. For that, I am looking for a reliable hosting company I can entrust my code to in the form of a number of Subversion repositories, and an installation of the Redmine project management tool. As my financial situation may vary during traveling, I am looking for something I can pay up front for a year or two, and is obviously not too pricey. I don't care where the company is located, as long as it's trustworthy and solid, meaning it's not likely to go out of business next month. Does anybody know good recommendations? Preferably from own, personal, good experience. I have looked at CVSDude / Codesion and while they are certainly great, they don't offer Redmine of course, and seem to be aiming toward bigger organizations mainly. What I would need: 2-5 Gigs of space minimum, freely distributable between SVN, and Redmine attachments Unlimited number of Subversion projects Access control (team members / checkout-only accounts / etc.) I don't mind configuring the svn settings on file basis myself I need the possibility to map a custom domain to the package that is hosted elsewhere Frequent backups and access to those backups through FTP or other means I have been running my own virtual server for this until now, but I don't want the hassle, especially on the security side, while I may not always have the internet connection to fix problems that may come up.

  Read the article

• Sync OneNote Notebooks to/on SkyDrive

  - by Sam

  I've got OneNote running on all computers in our house, using it all the time with several people and computers. The only drawback: I want to keep the copies of OneNote in sync without having to run a dedicated server myself. Right now one of my computers has a folder share, where all others sync to, but this is highly impractical since the computer is not always running. So my question is: is it possible to put the notebook files on a (private) SkyDrive Folder and have all the computers sync to there? This way all computers could keep in sync whenever they got access to the web. Can this be done? and, of course, How? [Update] Maybe I should not have taken knowledge about OneNote as granted: OneNote uses a propietary file format, but has a very good in-file-syncing, working on network shares. Generic 'just sync the complete file' won't be useful at all, because I'd just have 'file has changed on server and on client' conflicts all the time. The sync needs to know OneNote files and be able to sync the content - eg. OneNote itself needs to sync the files, not some generic sync tool.

  Read the article

• How to pass alias through sudo

  - by Tanktalus

  I have an alias that passes in some parameters to a tool that I use often. Sometimes I run as myself, sometimes under sudo. Unfortunately, of course, sudo doesn't recognise the alias. Does anyone have a hint on how to pass the alias through? In this case, I have a bunch of options for perl when I'm debugging: alias pd='perl -Ilib -I/home/myuser/lib -d' Sometimes, I have to debug my tools as root, so, instead of running: pd ./mytool --some params I need to run it under sudo. I've tried many ways: sudo eval $(alias pd)\; pd ./mytool --some params sudo $(alias pd)\; pd ./mytool --some params sudo bash -c "$(alias pd)\; pd ./mytool --some params" sudo bash -c "$(alias pd); pd ./mytool --some params" sudo bash -c eval\ "$(alias pd)\; pd ./mytool --some params" sudo bash -c eval\ "'$(alias pd)\; pd ./mytool --some params'" I was hoping for a nice, concise way to ensure that my current pd alias was fully used (in case I need to tweak it later), though some of my attempts weren't concise at all. My last resort is to put it into a shell script and put that somewhere that sudo will be able to find. But aliases are soooo handy sometimes, so it is a last resort.

  Read the article

• Membership in two domains

  - by imagodei

  Hello! I would your suggestions for an effective solution for a person, who needs to access resources in two Windows domains and wants to use one computer. It's about our CEO, who has accepted a second position in another company. Accessing files and folders isn't big problem. The greatest challenge I see is that he wants to conveniently access Exchange accounts in both companies; he would like to send and receive mail in single Outlook if possible (two profiles?) There is also a challenge with calendars: he would like to have one calendar for all activities from both Exchange accounts. Creating a POP3 account for accessing second Exchange server is a last resort, because obviously there is a problem with scheduling meetings and other calendar related tasks. Forwarding and receiving all mail/tasks on primary Exchange server is inconvenient because simple replying to original sender is disabled; and also when manually changing the recepient, he will receive mail from the wrong address. We were considering Virtualisation, that is setting up an instance of virtual machine inside existing installation and then joining this virtual computer to a second domain. Then installing another MS Outlook. This would of course mean two different Outlook accounts, two different calendars, but would at least enable our CEO to access all information from a single laptop. Does anyone have any other idea? I know setting up two domains on a single computer is a no-go (without much hacking at least), but effective workarounds are appreciate. The thing I am looking here is high usage/efficiency/productivity, but also as elegant solution from the administration point of view. Thank you very much (if you managed to read this through, this is a good sign ^_^ )

  Read the article

• How to allow writing to a mounted NFS partition

  - by Cerin

  How do you allow a specific user permission to write to an NFS partition? I've mounted an NFS share on my localhost (a Fedora install), and I can read and write as root, but I'm unable to write as the apache user, even though all the files and directories in the share on my localhost and remote host are owned by apache. For example, I've mounted it via this line in my /etc/fstab: remotehost:/data/media /data/media nfs _netdev,soft,intr,rw,bg 0 0 And both locations are owned by apache: [root@remotehost ~]# ls -la /data total 24 drwxr-xr-x. 6 root root 4096 Jan 6 2011 . dr-xr-xr-x. 28 root root 4096 Oct 31 2011 .. drwxr-xr-x 4 apache apache 4096 Jan 14 2011 media [root@localhost ~]# ls -la /data total 16 drwxr-xr-x 4 apache apache 4096 Dec 7 2011 . dr-xr-xr-x. 27 root root 4096 Jun 11 15:51 .. drwxrwxrwx 5 apache apache 4096 Jan 31 2011 media However, when I try and write as the apache user, I get a "Permission denied" error. [root@localhost ~]# sudo -u apache touch /data/media/test.txt' touch: cannot touch `/data/media/test.txt': Permission denied But of course it works fine as root. What am I doing wrong?

  Read the article

• Massive Memory Leaks?

  - by Mads

  Hi, I seem to have huge memory leaks, which are confusing me. I'm running fusion 3.1 / Windows 7 on Snow Leopard. It's a clean install with all upgrades applied. I've given fusion 8GB on a 14GB machine. I've installed VS2008 & Eclipse in Windows 7. Nothing unusual. Inside Task Manager in Windows 7, my memory footprint stays reasonable, at <2GB. But in OSX, Activity Monitor shows the footprint of vmware-vmx to be much larger. It starts at 2 GB, which seems fine, but whenever I'm actually doing anything in Windows, vmware-vmx's footprint grows at a few MB per second. After 20 mins or so it's using ~10GB and everything grinds to a halt. Throughout this, Task Manager still says I'm only using 2GB. And whatever I do in windows seems to increase vmware-vmx's memory footprint. Even closing down an application seems to make it go up. So is this par for the course in fusion? I was previously using parallels 3 / Vista under Leopard, and it worked fine. I'd assumed my new fusion config would work better, but this makes it completely unusable. (And apparently I can't even ask tech support unless I buy a support package...) Any advice much appreciated. Thanks

  Read the article

• Write permissions on uploaded files - PHP & Linux

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• Local references to old server name remain after Windows 2003 server rename

  - by imagodei

  I have a standalone Win 2003 server with Windows Sharepoint Services (WSS3) running on it. I had to rename the server and I had bunch of problems resulting from this. Note that the server is not in AD environment. Most obvious problems were with Sharepoint, which didn't work. I was somewhat naive to think it will work in the first place, but OK - I've solved this using step 1 & 3 from this site (TNX) Other curious behavior/problems remain. Most disturbing is that Sharepoint isn't able to send email notifications to participants. I noticed there are several references to old server name everywhere I look: in Registry, in Windows Internal Database (MICROSOFT##SSEE). I see instances of old server name in the Sharepoint Central Administration - Operations - Servers in farm. There is reference to a servers: oldname.domain.local oldname.local On one of those servers there is also Windows SharePoint Services Outgoing E-Mail Service (Stopped). Also, when I try to telnet locally to the mail server (Simple Mail Transfer Protocol (SMTP) service), I get a response: 220 oldname.domain.local Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Tue, 15 Jun 2010 13:56:19 +0200 IMO these strange naming problems are also the reason why email notifications from within Sharepoint don't work. Can anyone tell me how to correct/replace those references to oldservername? Why is the email service insisting on old name? Of course I would like to try it without reinstalling the server. TNX!

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• DNS failover in a two datacenter scenario

  - by wanson

  I'm trying to implement a low-cost solution for website high availability. I'm looking for the downsides of the following scenario: I have two servers with the same configuration, content, mysql replication (dual-master). They are in different datacenters - let's call them serverA and serverB. Users use serverA - serverB is more like a backup. Now, I want to use DNS failover, to switch users from serverA to serverB when serverA goes down. My idea is that I setup DNS servers (bind/powerdns) on serverA and serverB - let's call them ns1.website.com and ns2.website.com (assuming I own website.com). Then I configure my domain to use them as its nameservers. Both DNS servers will return serverA IP as my website's IP. If serverA goes down I can (either manually or automatically from serverB) change configuration of serverB's DNS, to return IP of serverB as website's IP. Of course the TTL will be low, as it's supposed to be in DNS failovers. I know that it may take some time to switch to serverB (DNS ttl, time to detect serverA failure, serverB DNS reconfiguration etc), and that some small part of users won't use serverB anyway. And I'm OK with that. But what are other downsides of such an approach? An alternative scenario is that ns1.website.com will return serverA IP as website's IP, and ns2.website.com will return serverB IP as website's IP. But AFAIK clients not always use primary nameserver and sometimes would use secondary one. So some small part of users would use serverB instead of serverA which is not quite what I'd like. Can you confirm that DNS clients behave like that and can you tell what percentage of clients would possibly use serverB instead of serverA (statistically)? This one also has the downside that when serverA goes back up, it will be automatically used as website's primary server, which is also a bad situation (cold cache, mysql replication could fail in the meantime etc). So I'm adding it only as a theoretical alternative. I was thinking about using some professional DNS failover companies but they charge for the number of DNS requests and the fees are very high (why?)

  Read the article

• Preferred mail system/server for a company?

  - by Trevoke

  Say you are responsible for setting up an email solution at a company. Which would be your choice? I know of the following options, but many of them not well: Gordano Mail System Exchange Exim Postfix Qmail Zimbra For having used it a little over two years, I really, really like Gordano Mail System. They offer a whole bunch of things, like calendaring, anti-spam, anti-virus, extremely complete and filterable logging options, aliases, a customizable webmail interface... And their software can be installed on both a Windows or Linux OS. In addition, their support is top-notch, their knowledgebase comprehensive (and, I will admit with a touch of pride, I have contributed, with my questions, to the addition of a few articles in there). Of course, they're not free, which can be a problem, but they're not Exchange, and they do offer pretty much everything that Exchange offers -- which is great if you want to stay away from that, but need all the features. Although, if you need a Blackberry Exchange Server, or something similar, I'm not sure what you should go for. So.. What would your choice be? Why? I've never played with a more DIY email solution, but I'm sure many people here have and wouldn't trade their setup for the world :)

  Read the article

• Is there a way to exclude a specific drive vdi from "snapshots" in VirtualBox?

  - by Graza

  ...or is there another space-efficient way of dealing with the page/swap file of the Guest O/S? I've realised that its quite possible/likely that one of the things which "bloats" the snapshot/diff vdi's when a snapshot is taken is the guest operating system's pagefile. For example, say I have a 2Gb swap-file in a Windows guest OS, and over the course of a few weeks the usage of the swap file has gone over 1Gb a couple of times. When I next create a snapshot, it seems likely that I'd be almost guaranteed around 1Gb of space taken up in the new differencing disk just because of changes in the swap file. Obviously (provided I never did "live" snapshots on running or paused machines, and only ever did them when the machine was shut down), I would not need any of the information in the swap file to be saved. So this would simply be a waste of 1Gb. I'm wondering if there's a way to attach a vdi to a VM and flag it as "exclude from snapshots" - which would mean I could put the swap file on a different vdi which would never be included in a snapshot. Or if anyone has any other suggestions. Or an explanation about why it might not be an issue. I could obviously delete and recreate a swap drive vdi every time I did a snapshot to achieve the same effect, but this is a little more effort than simply clicking "create snapshot"....

  Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >