Search Results

Search found 21809 results on 873 pages for 'display interfaces'.

Page 299/873 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >

• Ubuntu 8.04 server is not retaining a static IP address

  - by James Pierce

  I recently setup a linux box running Ubuntu 8.04 (to match another server with 8.04). I need to insure that this box has a static IP address and I changed /etc/network/interfaces to set up the static IP address and when I run sudo /etc/init.d/networking restart it works fine for a while, but always reverts back to 10.0.1.24 after being idle for a while. I also tried stopping/removing the dhcp client, but that didn't help. sudo /etc/init.d/dhcp stop sudo apt-get remove dhcp3-client Here is my /etc/init.d/networking: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.0.1.4 netmask 255.255.255.0 broadcast 10.0.1.255 gateway 10.0.1.1 Any thoughts? Thanks.

  Read the article

• Watchguard config, drop-in or mixed-routing mode?

  - by vfilby

  I have a Watchguard XTM 2 that is currently acting as a firewall and a router for my business network, I currently have the WG setup in mixed-routing mode and am happy with the current configuration. The reason I am curious about drop-in mode is because I would like to use all the interfaces on the back of the watchguard for the same subnet. My understanding is that drop-in mode will put them all on the same subnet, but it is unclear from the manual that the routing/firewall/vpn will still work as expected. This WG is right behind a DSL modem that is setup in bridge mode, so the WG is handling all PPPoE auth and routing for the network.

  Read the article

• vpnc Not Adding Internal DNS Servers to resolv.conf

  - by AJ

  I'm trying to setup vpnc on Ubuntu. When I run vpnc, my resolv.conf file does not get changed. It still only contains my ISP's name servers: #@VPNC_GENERATED@ -- this file is generated by vpnc # and will be overwritten by vpnc # as long as the above mark is intact nameserver 65.32.5.111 nameserver 65.32.5.112 Here is my /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.3 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 65.32.5.111 65.32.5.112 Any tips on how to troubleshoot/resolve this? Thanks in advance.

  Read the article

• Un-failing over a Cisco PIX 515e

  - by ABrown

  We had a power outage at our data center last week and when our dual PIX 515E running IOS 7.0(8) (configured with a failover cable) came back, they were in a failed over state where the Secondary unit is active and the Primary unit is standby I have tried 'failover reset', 'failover active', and 'failover reload-standby' as well as executing reloads on both units in a variety of orders, and they don't come back Primary/Active Secondary/Standby. The only thing in my arsenal that I haven't tried is driving to the data center and performing a hard reboot, which I hate to do. I have read How Failover Works on the Cisco Secure Firewall and it seems like this should be wicked straight forward. output of show failover on Primary: Failover On Cable status: Normal Failover unit Primary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:52:05 UTC Mar 10 2010 This host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Other host: Secondary - Active Active time: 897045 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. output of show failover on Secondary: Failover On Cable status: Normal Failover unit Secondary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:03:04 UTC Feb 28 2010 This host: Secondary - Active Active time: 896925 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Other host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. I'm seeing the following in my syslog: Mar 10 03:05:00 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:05:09 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reload-standby' command. Mar 10 03:05:12 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:05:12 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:06:09 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:06:10 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:06:10 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:06:23 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:06:23 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:06:24 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. Mar 10 03:07:05 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:07:31 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover active' command. Mar 10 03:08:04 fw1 %PIX-5-611103: User logged out: Uname: enable_1 Mar 10 03:08:04 fw1 %PIX-6-315011: SSH session from admin1_int on interface inside for user "pix" terminated normally Mar 10 03:08:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:08:39 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:09:10 fw1 %PIX-6-605005: Login permitted from admin1_int/36891 to inside:192.168.4.4/ssh for user "pix" Mar 10 03:09:23 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:09:38 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:09:52 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:09:52 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:09:53 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. I'm not exactly sure how to interpret that syslog data. Primary doesn't seem to even try to become Active. When I reload the individual units separately, my connections are retained, so it doesn't seem like I have a real hardware failure. Is there something I can query (IOS or SNMP) to check for hardware issues? Any thoughts? My IOS-fu is weak. Thanks for any help you might provide, Aaron

  Read the article

• BSOD Before Windows Will Loads - Graphics Related

  - by Brian

  Alright deep breath here: (Windows 7 Home Premium 64 bit btw) Today I installed Star Craft 2 Beta. After trying to log in, it had some issues where it said my device stopped working (referring to my video device I have to imagine). After I force quit the game there were some random "hot" (various colors if i remember correctly) pixels on the screen. I decided to reboot and try again with similar results. I figured that maybe my display drivers could stand to be updated (I don't frequently update them as I don't often run into problems). I went out to nVidia's website and grabbed the latest drivers for Windows 7 64 bit GeForce 9 series. (I have SLi-ed 9800 GTs). Everything seemed to install fine and I performed the restart. This is when things went from bad (can't play SC2 beta ;) ) to worse (can't boot into windows!). Initially the very first splash screen - I think it's the bios splash screen - had lines of colored pixels covering it. It then displayed a screen that had lots of "(" on it. After that it showed the normal windows 7 splash screen as if it were going to load into Windows. Before getting much further, it BSODed on me. It was a 0x0000003B stop error. At nvlddmkm.sys. A little digging let verified that this was a problem with an nVidia graphics device, not a real shocker. Windows decided it would try to help me diagnose the problem, which it's only answer to was a System Restore, which did nothing to alleviate the problem. I was able to boot up fine in safe mode and was not able to roll back the driver, however I did uninstall the driver and reboot. I still had the graphical anomalies during the first two screens (same colored "."'s and weird "("'s), but there was NOT a stop error. Windows loaded up, found a default driver for the device and installed it and I restarted to let it load - and had yet another BSOD Stop error. Repeat driver uninstall, this time I reloaded the same version (I think it's possible that I was running a 32 bit version or a vista versus windows 7 version, but I don't have that information handy) of the nVidia driver from their website. Restart, same anomalies, same Stop Error. I am at a loss - At this point all I can think is that the firmware for the Video cards got fried or there's actual damage to the cards which I sincerely hope is not the case but the sooner I know the better. Any insight into what I might be able to do to troubleshoot/fix this problem would be most helpful. Attached below is a dump from DxDiag. Please let me know if there is more info that I could provide. ------------------ System Information ------------------ Time of this report: 3/18/2010, 23:22:48 Machine name: BRIAN-PC Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600) (7600.win7_rtm.090713-1255) Language: English (Regional Setting: English) System Manufacturer: Dell Inc System Model: XPS 630i BIOS: Phoenix - AwardBIOS v6.00PG Processor: Intel(R) Core(TM)2 Quad CPU Q8200 @ 2.33GHz (4 CPUs), ~2.3GHz Memory: 8192MB RAM Available OS Memory: 8190MB RAM Page File: 1855MB used, 14521MB available Windows Dir: C:\Windows DirectX Version: DirectX 11 DX Setup Parameters: Not found User DPI Setting: Using System DPI System DPI Setting: 96 DPI (100 percent) DWM DPI Scaling: Disabled DxDiag Version: 6.01.7600.16385 32bit Unicode DxDiag Previously: Crashed in DirectShow (stage 1). Re-running DxDiag with "dontskip" command line parameter or choosing not to bypass information gathering when prompted might result in DxDiag successfully obtaining this information ------------ DxDiag Notes ------------ Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. -------------------- DirectX Debug Levels -------------------- Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) --------------- Display Devices --------------- Card name: Manufacturer: Chip type: DAC type: Device Key: Enum\ Display Memory: n/a Dedicated Memory: n/a Shared Memory: n/a Current Mode: 1600 x 1200 (32 bit) (1Hz) Driver Name: Driver File Version: () Driver Version: DDI Version: unknown Driver Model: unknown Driver Attributes: Final Retail Driver Date/Size: , 0 bytes WHQL Logo'd: n/a WHQL Date Stamp: n/a Device Identifier: {D7B70EE0-4340-11CF-B123-B03DAEC2CB35} Vendor ID: 0x0000 Device ID: 0x0000 SubSys ID: 0x00000000 Revision ID: 0x0000 Driver Strong Name: Unknown Rank Of Driver: Unknown Video Accel: Deinterlace Caps: n/a D3D9 Overlay: n/a DXVA-HD: n/a DDraw Status: Not Available D3D Status: Not Available AGP Status: Not Available ------------- Sound Devices ------------- Description: Speakers (Realtek High Definition Audio) Default Sound Playback: Yes Default Voice Playback: Yes Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Realtek Digital Output (Realtek High Definition Audio) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Realtek HDMI Output (Realtek High Definition Audio) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0888&SUBSYS_10280249&REV_1001 Manufacturer ID: 1 Product ID: 100 Type: WDM Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail WHQL Logo'd: n/a Date and Size: 8/18/2008 04:05:28, 1485592 bytes Other Files: Driver Provider: Realtek Semiconductor Corp. HW Accel Level: Basic Cap Flags: 0x0 Min/Max Sample Rate: 0, 0 Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No --------------------- Sound Capture Devices --------------------- Description: Microphone (Realtek High Definition Audio) Default Sound Capture: Yes Default Voice Capture: Yes Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail Date and Size: 8/18/2008 04:05:28, 1485592 bytes Cap Flags: 0x0 Format Flags: 0x0 Description: Realtek Digital Input (Realtek High Definition Audio) Default Sound Capture: No Default Voice Capture: No Driver Name: RTKVHD64.sys Driver Version: 6.00.0001.5667 (English) Driver Attributes: Final Retail Date and Size: 8/18/2008 04:05:28, 1485592 bytes Cap Flags: 0x0 Format Flags: 0x0 ------------------- DirectInput Devices ------------------- Device Name: Mouse Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: Keyboard Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: ESA FW Update Attached: 1 Controller ID: 0x0 Vendor/Product ID: 0x0955, 0x000A FF Driver: n/a Poll w/ Interrupt: No ----------- USB Devices ----------- + USB Root Hub | Vendor/Product ID: 0x10DE, 0x026D | Matching Device ID: usb\root_hub | Service: usbhub | +-+ USB Input Device | | Vendor/Product ID: 0x0955, 0x000A | | Location: Port_#0002.Hub_#0001 | | Matching Device ID: generic_hid_device | | Service: HidUsb | | | +-+ HID-compliant device | | | Vendor/Product ID: 0x0955, 0x000A | | | Matching Device ID: hid_device | | +-+ USB Input Device | | Vendor/Product ID: 0x046D, 0xC01E | | Location: Port_#0003.Hub_#0001 | | Matching Device ID: generic_hid_device | | Service: HidUsb | | | +-+ HID-compliant mouse | | | Vendor/Product ID: 0x046D, 0xC01E | | | Matching Device ID: hid_device_system_mouse | | | Service: mouhid ---------------- Gameport Devices ---------------- ------------ PS/2 Devices ------------ + Standard PS/2 Keyboard | Matching Device ID: *pnp0303 | Service: i8042prt | + Terminal Server Keyboard Driver | Matching Device ID: root\rdp_kbd | Upper Filters: kbdclass | Service: TermDD | + Terminal Server Mouse Driver | Matching Device ID: root\rdp_mou | Upper Filters: mouclass | Service: TermDD ------------------------ Disk & DVD/CD-ROM Drives ------------------------ Drive: C: Free Space: 324.3 GB Total Space: 608.4 GB File System: NTFS Model: WDC WD64 00AAKS-75A7B SCSI Disk Device Drive: D: Free Space: 1.0 GB Total Space: 2.0 GB File System: NTFS Model: WDC WD64 00AAKS-75A7B SCSI Disk Device Drive: E: Model: TSSTcorp DVD+-RW TS-H653F SCSI CdRom Device Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7600.16385 (English), , 0 bytes -------------- System Devices -------------- Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_03B7&SUBSYS_000010DE&REV_A1\3&2411E6FE&1&18 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AF&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0A Driver: n/a Name: PCI standard host CPU bridge Device ID: PCI\VEN_10DE&DEV_03A3&SUBSYS_02491028&REV_A2\3&2411E6FE&1&00 Driver: n/a Name: NVIDIA nForce Serial ATA Controller Device ID: PCI\VEN_10DE&DEV_0267&SUBSYS_02491028&REV_A1\3&2411E6FE&1&78 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B6&SUBSYS_02491028&REV_A1\3&2411E6FE&1&10 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AE&SUBSYS_02491028&REV_A1\3&2411E6FE&1&09 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_0272&SUBSYS_02491028&REV_A3\3&2411E6FE&1&52 Driver: n/a Name: NVIDIA nForce Serial ATA Controller Device ID: PCI\VEN_10DE&DEV_0266&SUBSYS_02491028&REV_A1\3&2411E6FE&1&70 Driver: n/a Name: LSI 1394 OHCI Compliant Host Controller Device ID: PCI\VEN_11C1&DEV_5811&SUBSYS_02491028&REV_70\4&14591D7E&0&2880 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B5&SUBSYS_02491028&REV_A1\3&2411E6FE&1&06 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AD&SUBSYS_02491028&REV_A1\3&2411E6FE&1&08 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_0270&SUBSYS_02491028&REV_A2\3&2411E6FE&1&48 Driver: n/a Name: Standard Dual Channel PCI IDE Controller Device ID: PCI\VEN_10DE&DEV_0265&SUBSYS_02491028&REV_A1\3&2411E6FE&1&68 Driver: n/a Name: NVIDIA GeForce 9800 GT Device ID: PCI\VEN_10DE&DEV_0605&SUBSYS_062D10DE&REV_A2\4&4BABE2A&0&0028 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B4&SUBSYS_02491028&REV_A1\3&2411E6FE&1&07 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AC&SUBSYS_02491028&REV_A1\3&2411E6FE&1&01 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_026F&SUBSYS_CB8410DE&REV_A2\3&2411E6FE&1&80 Driver: n/a Name: NVIDIA nForce PCI System Management Device ID: PCI\VEN_10DE&DEV_0264&SUBSYS_02491028&REV_A3\3&2411E6FE&1&51 Driver: n/a Name: NVIDIA GeForce 9800 GT Device ID: PCI\VEN_10DE&DEV_0605&SUBSYS_062D10DE&REV_A2\4&10BD3C89&0&0018 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B3&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0E Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AB&SUBSYS_02491028&REV_A1\3&2411E6FE&1&04 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_10DE&DEV_026E&SUBSYS_02491028&REV_A3\3&2411E6FE&1&59 Driver: n/a Name: PCI standard ISA bridge Device ID: PCI\VEN_10DE&DEV_0260&SUBSYS_02491028&REV_A3\3&2411E6FE&1&50 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03BC&SUBSYS_02491028&REV_A1\3&2411E6FE&1&11 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B2&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0D Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03AA&SUBSYS_02491028&REV_A1\3&2411E6FE&1&02 Driver: n/a Name: Standard OpenHCD USB Host Controller Device ID: PCI\VEN_10DE&DEV_026D&SUBSYS_02491028&REV_A3\3&2411E6FE&1&58 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03BA&SUBSYS_02491028&REV_A1\3&2411E6FE&1&12 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B1&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0C Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03A9&SUBSYS_02491028&REV_A1\3&2411E6FE&1&03 Driver: n/a Name: High Definition Audio Controller Device ID: PCI\VEN_10DE&DEV_026C&SUBSYS_02491028&REV_A2\3&2411E6FE&1&81 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_10DE&DEV_03B8&SUBSYS_000010DE&REV_A1\3&2411E6FE&1&28 Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03B0&SUBSYS_02491028&REV_A1\3&2411E6FE&1&0B Driver: n/a Name: PCI standard RAM Controller Device ID: PCI\VEN_10DE&DEV_03A8&SUBSYS_02491028&REV_A2\3&2411E6FE&1&05 Driver: n/a Name: NVIDIA nForce Networking Controller Device ID: PCI\VEN_10DE&DEV_0269&SUBSYS_02491028&REV_A3\3&2411E6FE&1&A0 Driver: n/a --------------- EVR Power Information --------------- Current Setting: {5C67A112-A4C9-483F-B4A7-1D473BECAFDC} (Quality) Quality Flags: 2576 Enabled: Force throttling Allow half deinterlace Allow scaling Decode Power Usage: 100 Balanced Flags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 50 PowerFlags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 0

  Read the article

• Wireless networking on Gnome on Ubuntu 9 / 10

  - by WaveyDavey

  So here's my problem: I have some netbooks (ASUS eee, and ACER Aspire Ones) that I've been tasked to set up as kiosk machines, locked up tight for normal users. I am a command-line, server man, so this gnome malarkey is all a bit new to me. I found a lovely 9.04 kiosk livecd that installs and runs exactly as I want it to, but I can't get the wireless working. So I dropped on a full 10.4 distro, and wireless works straight out of the box (so hardware is good) - all I needed to do was right-click on the network connection icon, enter my SSID and password (WPA/WPA2) and away it went, perfect. Further investigation on 10.4 distro shows that /etc/networking/interfaces is virtually empty (just auto lo iface lo inet loopback in it), even after I have set up the wireless thru the gnome taskbar applet (is that the right word?). So where does gnome / ubuntu store the network settings to bring the blasted wireless connection up, and what do I need to do on the kiosk version to get wireless running?

  Read the article

• Double default gateway ubuntu server

  - by Elena

  Hi, I've just installed an Ubuntu server 9.10 on an EEEBox. This is my /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.48.16 netmask 255.255.248.0 wireless-essid mynet auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask 255.255.255.224 gateway xx.xx.yy.yy When I restart /etc/init.d/networking, I can access the eth0 ip address from the internet and I can ping the machines in my wifi network mynet. Everything works fine and I have one default gateway. But after some time if I check again the route I just find two default gateways: one is correct and is the previous one, but the other is the one of the wifi network. I have a quite low signal of mynet where my server is and sometimes the wifi just disconnect and then reconnect again. Then I think that this can be a problem and the dhcp of the wifi net, when reconnecting it also add a default gateway. Any idea on how to resolve this issue?

  Read the article

• error in php not logging or displaying

  - by Grant M

  I can not get any errors to display on screen on write to a log file. When check phpinfo() print out I have same value of master a local for display_errors On display_startup_errors On error_log /var/log/php.log error_reporting E_ALL & ~E_NOTICE log_errors On log_errors_max_len ls -l /var/log/php.log is -rw-rw-rw- 1 root root 0 Jun 21 07:47 /var/log/php.log for /var and /varlog drwxrwxrwx 23 root root 4096 Jun 2 11:13 var when there is an error in the code the page the browsers shows nothing and browser says there is no source for the page. Any suggestions of where else to look or change to errors to appear somewhere (anywhere would be good) edit: my error script is now <?php ini_set('display_errors', 1); error_reporting(E_ALL); echo "print from error.php 2 "; error //print from erroerror to cuase logging to happen. ?> this will print on display and to log Notice: Use of undefined constant error - assumed 'error' in /var/www/piku_dev2/error.php on line 7 but if I put garbage like #@$%$ on the error line I get nor error messages anywhere. Edit2: The problem turned out to in the httpd.conf file. I don't know what it was yet as it was fixed y someone else.

  Read the article

• GNU screen, how to get current sessionname programmably

  - by Jimm Chen

  [ This can be considered step 2 of my previous question Is it possible to change GNU screen session name after created? ] Actually, I'd like to write a script that can display current screen session name and change current session name. For example: sren armcross It will change the session name to armcross (ARM gcc cross compiler) and output something like: screen session name changed from '25278.pts-15.linux-ic37' to 'armcross' So, the key question now is how to get current session name. Not only for display the old session name, but according to Is it possible to change GNU screen session name after created? , I have to know it(pass to -d -r) before I can change it to something else. Can we use $STY for current session name? No. $STY will not change after you have changed the session name to a user-defined one. However, for command screen -d -r <oldsessname> -X sessionname armcross should be the user-defined name(if ever defined) instead of $STY, otherwise, screen spouts error "No screen session found." Maybe, there is a verbose way, use screen -list to list all sessions(user-defined name listed), then, match the pid part from $STY against those listed sessions and we will find current session's user-defined name. It should not be so verbose for such a straightforward question. Don't you think so? The -d -D and -r -R options seems to expose too much implementation detail to screen's user. It seems, to rename a session, you have to detach it, then do the rename, then reattach it. Right? My env: opensuse 11.3, GNU screen 4.00.03 (FAU) 23-Oct-06 Thank you.

  Read the article

• How to get my external IP address (over NAT) from the Windows command-line?

  - by Diogo Rocha

  The Windows "ipconfig" command can only show me the parameters from the Ethernet interfaces from my machine (even with the "ipconfig /all" argument). It can show detailed information about the interface, but it will never show me my external IP address over a NAT network. However, there are several websites, such as "What is my IP address" that can get and show my external IP address. So I'm wondering, is possible to get this value externally? Should I expect that there is some way to get this information from a command line at my local machine... I need to get this value to log on an application that I'm doing with VBScript. There is some way to do this, from a "cmd" on Windows?

  Read the article

• Useful scripts for Sikuli

  - by Ivo Flipse

  Thanks to Lifehacker I came across Sikuli which is described as: Sikuli is a visual technology to search and automate graphical user interfaces (GUI) using images (screenshots). The first release of Sikuli contains Sikuli Script, a visual scripting API for Jython, and Sikuli IDE, an integrated development environment for writing visual scripts with screenshots easily. Sikuli Script automates anything you see on the screen without internal API's support. You can programmatically control a web page, a desktop application running on Windows/Linux/Mac OS X, or even an iphone application running in an emulator. As this looks very promising, perhaps complementary to AutoHotKey I'm curious what scripts you guys will come up with. Especially since this program is portable and could solve "simple" Super User problems. Example script from their documentation: setThrowException(True) setAutoWaitTimeout(10000) switchApp("System Preferences.app") click() click() click() click() wait() type("192.168.0.1\t") type("255.255.255.0\t") type("192.168.0.254\t") click()

  Read the article

• Is bonding mode=5 a solution against MAC flapping?

  - by Yuri

  There is two are interconnected Cisco WS-2950T. By the one GBIC port on first switch connected a first NIC of bonding interface, and by the one GBIC port on second switch connected a second NIC of bonding interface. Of course the both switches sees the bonding MAC-address only on one interface (eg it is GBIC on first switch) and all incoming traffic for bonding interface passes through this GBIC. But in "mode=5" all outgoing traffic are distributed between the all interfaces that make bond. In this case, the packets will be dropped from the second switch and anyway will going through the first switch? Or the division will be working?

  Read the article

• Which tools should I use to work efficiently on a remote server?

  - by Konstantin

  I rented a virtual ubuntu server and am trying to setup a web application. I am working from ubuntu. I know how to use the command line, but it is slow and as a visual person, I prefer graphical interfaces. So I connected with nautilus via ssh and was now able to browse the directories graphically. But my permissions are just those of "other", so I cannot do much without o+rwx. What tools do you use to do setup and administrate your servers? Should I write code locally rather then directly on the server and rsync it? EDIT: It is NOT a production server, I am simply fiddling around there.

  Read the article

• CORAID using only 1 of the 2 available NICs for AoE traffic

  - by Peter Carrero

  We got 6 CORAID shelves in my workplace. On 2 of them I see AoE traffic on only 1 of the 2 NICs that are attached to the SAN switch. We got jumbo frames enabled on all devices. Both NICs show up when I issue the aoe-interfaces command. This wouldn't bother me too much if the throughput performance observed on the "bad" shelves using bonnie++ wasn't half of the result of the "good" shelves. The "good" shelves are older SR1521 model and they have ReiserFS on their LUNS - not that I think it makes a difference - and the "bad" shelves are newer SR2421 model and have JFS. Any help as to what is going on and how to rectify this would be greatly appreciated. BTW: even the lower performing shelves outperform another iSCSI device we got, but that is another story... Thanks.

  Read the article

• KVM virtual machine networking, NAT and bridge together

  - by stoqlt

  I have two running KVM guests on an Ubuntu (Lucid) host. One of them uses the simplest NAT method, and DHCP inside. The other uses the bridge method and static IP inside. Both work fine. Can I mix the networking methods? I'd like to create some set of scripts which used the local 192.168.122.x address, no matter if the guest has or not has an additional bridged LAN interface. Having eth0 and eth1 interfaces inside would be fine. Thanks for your interest.

  Read the article

• Start script on network connect

  - by Nate Mara

  I am trying to get a GNU/Linux Bash script to run as soon as a network connection is established on my Raspberry Pi. I tried following the instructions on several pages: I have tried adding my script to /etc/network/if-up.d and running sudo chmod ugo+x on the file. I have tried adding the line post-up <path/to/script.sh> to /etc/network/interfaces I am really quite clueless here. More info: The script runs fine when manually run, here it is: http://pastebin.com/UJvt5HYU (I did remove my personal info (email addresses, passwords), but other than that, the script is unchanged. This script also uses the sendEmail program (can be found at http://caspian.dotconf.net/menu/Software/SendEmail/).

  Read the article

• Issues with ForceBindIP on Windows 7 (x64)

  - by Craig

  I am desperately needing a solution to binding certain applications to specific network interfaces. ForceBindIP seems to be my only solution. Although the website claims it works up to XP, Google says that many users running 7 have had it work successfully. I have UAC disabled, yet still: Does anyone know why this is happening? If not, does anyone know a viable alternative to ForceBindIP? I'm a gamer and I'm addictively trying to torrent on a secondary connection while playing games online.

  Read the article

• Load-balancing between a Procurve switch and a server

  - by vlad

  Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

  Read the article

• How to get my external IP address(over NAT) from Windows command-line?

  - by Diogo Rocha

  Windows "ipconfig" command can only show me the parameters from the ethernet interfaces from my machine(even with the "ipconfig /all" argument), it can show detailed information about the interface, but will never show me my external IP address over a NAT network. However, there are several websites, such as "What is my IP" that can get and show my external IP addres. So I'm wondering, if is possible to get this value externally, should I expect that there is some way to get this information from a command line at my local machine... I need to get this value to log on an application that I'm doing with VB Script. There is some way to do this, from a "cmd" on Windows?

  Read the article

• Watchguard firebox: public IP addresses behind firewall with as much usable IP addresses as possible

  - by martinezpt

  Our ISP assigned us 16 public IP addresses that we want to assign to hosts behind a Watchguard firebox x750e. The IP addresses are: x.x.x.176/28 of which x.x.x.177 is the gateway. The hosts will be running software that needs to be directly assigned the public IP address so 1:1 NAT is not an option. I found this document that gives examples on how to assign public IP addresses to hosts behind the firewall, using an optional interface: http://www.watchguard.com/help/configuration-examples/public_IP_behind_XTM_configuration_example_(en-US).pdf However, I can't implement scenario 1 as it won't allow me to use the same subnet on both interfaces. As for scenario 2, splitting the address range into 2 subnets will decrease the usable hosts on the optional interface to 5 (8 - network - broadcast - optional interface ip). I'm convinced that there must be a better way to address this problem and maximize the number of usable IP addresses but I'm not very familiar with this specific firewall. Are there any suggestions on how to keep the hosts behind the firewall with public IP addresses while maximizing the usable IP addresses? thanks

  Read the article

• PHP 5.3 on IIS gives 404 error in CGI mode

  - by reinier

  Slowly losing my mind here. I had PHP 5.2 working fine (ISAPI) under IIS, but for some extension I needed 5.3. So no worries, I installed this but it turns out ISAPI is not supplied anymore. I followed the install tutorials for fastcgi and ended up with a 500 internal server error for every PHP page served. So my current situation is: I have fastcgi removed. In my websites I have added PHP (head, get, post) and routed them to c:\php\php-cgi.exe. Result: every PHP page I try (even the ones with just text) gives 404 not found error. Any HTML file I put in the same folder, serves without a hitch. Who can help me please... How hard can something like this be right? For me apparently very hard. Extra information: ran the installer as suggested below. Set it to use fastcgi. my fcgiext.ini file looks like this now: [types] php=c:\php\php-cgi.exe [c:\php\php-cgi.exe] exepath=c:\php\php-cgi.exe from the command-line a 3 line PHP file with just phpinfo(); works fine from the server the same PHP file with just phpinfo(); results in the internal server 500 error. from the server a PHP file with just text works fine when changing the document types in IIS management console and point the PHP extension directly to c:\php\php-cgi.exe results in 404 for every PHP file the php.ini is the php.ini.production file which came in the distribution. No edits were made. Setting the IIS PHP handler directly to PHP (not via fastcgi) c:\php\php-cgi.exe results in the following: display a PHP page with only text....works fine display a page with only phpinfo(); results in 404 not found

  Read the article

• Ethernet interface number changed, and old one does not exist, but does not leave IP address

  - by Sagar

  I have a virtual machine with Mandriva 2007.0 (yes, old - unfortunately we do not have a choice here). Anyway, the problem: Before reboot: active network interface = eth0. No other interfaces present, and network manager confirms this. Static IP address set to 172.31.2.22. No issues, everything working properly, routing et al. -------Reboot--------- After reboot: active network interface = eth1, with a DHCP address. Network manager shows eth0 as disconnected, and not connectable. When I try to set eth1 up with the static IP address (same one), it says "In Use". I then tried ifconfig eth0 172.31.2.29 just to free it up from the eth0 interface so I could use it with eth1 (since this is connected). Result: ifconfig eth0 172.31.2.29 SIOCSIFADDR: No such device eth0: unknown interface: No such device Nothing else changed. Any ideas what could be happening, or at least how I can get my IP address back?

  Read the article

• How could two processes bind onto the same port?

  - by Matt Ball

  I just ran into an issue where a request made to localhost:8080 from curl was hitting a different server than the same request made from inside Node. lsof -i :8080 revealed that two processes were both binding onto the same port: COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME node 51961 mball 14u IPv4 0xd980e0df7f175e13 0t0 TCP *:http-alt (LISTEN) java 62704 mball 320u IPv6 0xd980e0df7fe08643 0t0 TCP *:http-alt (LISTEN) How is this possible? Were they binding onto different interfaces? Or was it the IPv4 vs 6? If you're curious, node was hitting the other node process, curl was hitting the java process. The java process was started after the node process.

  Read the article

• Stop Cisco AnyConnect from locking down the NIC

  - by Johannes Rössel

  Cisco's VPN crapclients (including the AnyConnect one) have the nasty habit of clobbering all NICs on the system you're using them. The old client had a checkbox in the connection options that allowed you to use other network interfaces while being connected while the AnyConnect client doesn't have any options at all, seemingly. But they both lock down the network interface they are using to connect to the VPN. Since I am forced to use AnyConnect to actually have an internet connection and I like to control a second computer at home via RDP (over the same network interface so far) this doesn't quite work out. With the old client IPv6 still worked just fine, though AnyConnect seems to dislike that as well now. Is there any way to still use the same network interface for LAN access? I actually don't really care about any possible security implications (which might be why Cisco does this) as it's my freaking internet connection and not a secure way of working from home. The trade-off is quite different :-)

  Read the article

• Routing based on source address in Windows Server 2008 R2

  - by rocku

  Hi, I'm implementing a direct routing load balanced solution using Windows Server 2008 R2 as back-end server. I've configured a loopback interface with the external IP address. This works, I am receiving packets with the external IP address and respond to them appropriately. However our infrastructure requires that traffic which is being load-balanced should go through a different gateway then any other traffic originating from the server, ie. updates etc. So basicly I need to route packets based on source address (external IP) to another gateway. The built-in Windows 'route' command allows routing based on destination address only. I've tried setting a default gateway on the loopback interface and mangled with weak/strong host send/receive parameters on the interfaces, however this didn't work. Is there any way around this, possibly using third party tools?

  Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >