Search Results

Search found 57650 results on 2306 pages for 'windows (vista)'.

Page 299/2306 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306 | Next Page >

Windows 2008 Print Server issue

- by HokieMike

I have a dedicated windows 2008 server I use as a file server and print server at my home office. Whenever I print documents from one of my clients, I see the document hit the queue on the server immediately (says its in "printing" status), but it takes FOREVER to print out (like over 5 minutes). But, printing the same document locally from the server takes 4 seconds. It's an HP 1006P laser printer. I am running 32-bit 2008 Server. Installed the Vista drivers ( updated to latest version ). Tried updating the drivers on the clients too and no dice. Any ideas on how to troubleshoot?

Read the article
Windows clients not using NTP server provided via DHCP

- by gencha

I have a network consisting mostly of Windows Vista and 7 clients and an Ubuntu server. The server provides both the DHCP and NTP services through dhcp3-server and openntpd. In my dhcpd.conf, the subnet is declared as follows: subnet 10.10.10.0 netmask 255.255.255.0 { range 10.10.10.10 10.10.10.200; option broadcast-address 10.10.10.255; option routers 10.10.10.1; option ntp-servers 10.10.10.1; } The clients don't seem to be using the NTP server though. When I capture the network traffic with Wireshark during the DHCP process, I also see no mention of the NTP option in the DHCP offer message. I am not quite sure if the clients would have to specifically request that option to receive it or if I have to make another configuration to offer the option.

Read the article
windows seven disk check error

- by crazybmanp

i have gotten the error in the microsoft KB article 975778 (http://support.microsoft.com/kb/975778/en-us) i was able to get onto my computer luckily, but when i went on to get the hotfix that is stated in the article, it gave me this error when i ran it: "the update is not applicable to your computer." is there any way of getting the disk check error to stop, or to get this fix to work. i will answer any questions on hardware if you post the questions in the comments. answers to questions this is the a full version that i got from ASUS as an upgrade disk from windows vista (hopefully more specific than you were asking)

Read the article
Media Sharing on Windows Server 2008 R2

- by HCL

I want a Server 2008R2 (x64) to act as DNLA-Server. I remember I tried this with a Server 2008 about two years ago and this was only possible with some ugly hacks. Is it on Server 2008R2 now possible to enable Windows MediaPlayer Media-Sharing by installing the desktop experience packet? Has someone already experience on this. Or is there another possibility to allow media sharing on a Server 2008R2 "the designated way"? I remember that on Server 2008 the way was to install the old MediaConnect-Pacakge. But I hesitate to install such a component on a server. Anciently I installed VirtualServer with Vista and enabled the media server there in, but this seems to me somewhat overkill for such a simple task.

Read the article
Web based console connections not working in Windows 7 posted: Jan 20, 2010 8:55 AM

- by nmeth

For slightly complicated reasons we tend to give people console access to VMs via the webui. This has worked fine in the past, however when the users update their client machines to Windows 7 (or Vista, I am told, although I have not tested that), then the console fails to work. On IE8, having allowed the ActiveX control, the tab causes a "Internet Explorer has stopped working" dialog. On Firefox 3.5 , once the plugin has been installed, using the console causes the browser to crash. I've updated to the most recent VC 2.5 release, and ESX 3.5u5. Anyone else seeing this? Any clues how to get round it (other than using the fat client). Nigel.

Read the article
What prevents Windows from entering standby?

- by Arne

Is there a tool or method to find out, what prevents Windows Vista 32 bit from entering the standby mode? My home pc is set to standby after a certain time of inactivity. But quite often it just stays awake and I have know idea why. I know of things that will keep it awake and already checked devices and network to no avail. I suspect there is some application or service that tells the os to stay active and I hope there is some tool to find the culprit.

Read the article
How to play games in widescreen in Windows 7, Dell Studio 1555

- by blasteralfred

I have a dell studio 1555 laptop with a GPU inside. The details are below; Hardware details Software details I can play games in widescreen in Vista, but not in 7. I am using Windows 7 Home Premium. I have the latest Catalyst Control Center. Instead of widescreen, the games are running in a classic style, say 1024x768 ratio. When I play need for speed underground, the maximum possible resolution is 1024x768 (all other games are like this). I have no problem with HD videos and anything else. How can I fix this? Thanks in advance...:)

Read the article
Run a command from Windows 7 Start Menu

- by Abhijeet Patel

I'm trying to run commands such as "cmd.exe", "appwiz.cpl" etc by typing it in the Search box of the Start Menu in Windows 7 (x86). I'm able to do this just fine in Vista. After typing in "cmd" I notice that I see a link to "Programs" in the start menu so it seems that "cmd" is being recognized but when I click on "Programs" link which is shown,I get the following message. "These files can't be opened. Your internet security settings prevented one or more files from being opened" P.S. - I'm not looking for enabling the "Run" command to show in the Start Menu Any help would be much appreciated

Read the article
Windows 7 - You don't have permissions to save in this folder

- by James

Huh? I'm getting this message - "You don't have permissions to save in this folder" - even though I am the only user on this machine, and administrator. How can I set permissions for myself to do everything, everywhere (including saving deleting etc)? Thanks. Edit: Sorry, forgot to say which folder it was. It is a folder in Program Files, where I save my PHP files for local testing. Sorry if Im a bit daft with all this, but I've upgraded straight from XP to 7, and having never used vista, I'm used to being allowed to have full control.

Read the article
Windows Server vs Sharing

- by Mark Lawrence

Not sure if this is the right place for this question. I have a friend that owns a small business running 3 local machines, that are connected to the internet, and a server that each local machine connects to. He has recently bought a newer server, and by server I mean a Windows Vista box. He wants to use this purely to store data that the 3 local machines can access, kind of like a glorified external hard drive. Im suggesting to fore-go the server option and simply setup sharing on the 'server' box. Interested in hearing any suggestions as to whether the server idea is preferable?

Read the article
Video problem with Windows 7 Games

- by Jordan 1GT

I have a Dell xps M1330 which originally ran Vista, but I upgraded to Windows 7. When I try to run a Win 7 game like spider solitaire I receive the following message: "The game is running in software rendering mode. Hardware acceleration is either disabled or not supported by your video card driver which could slow down game performance. Make sure you have the latest video card driver installed and that hardware acceleration is turned on." I confirmed that hardware acceleration is turned on. When I go to Dell's site, I'm told there is no later video driver. When I run the game it runs very choppy. I wouldn't care, but I loaded a .pptx file which is doing strange things in normal view and I suspect may be related to the same video problem. Any ideas?

Read the article
How do I execute a script or program on Windows Shut Down

- by Subhen

I want to run a exe or bat file when window shut down? I want to unmount few drives , which are mounted by my application , when user shutdown the system. For that I need to execute another exe on shutdown, which will disconnect drives mounted by my app. I got few links which shows we can create a entry in Group Policy to execute a programe while window shut down. I am not sure how I can add a entry to Group ploicy by C++ code. Again , group policy doesn't work with Win Vista. Any other better approach ?

Read the article
Remap key combinations in Windows

- by nickf

This question is similar to this one, but the accepted solution doesn't work in my case. I work on two different laptops. On one, the Home and End keys are only available by pressing Fn+Left and Fn+Right. This can make it rather annoying when switching between the two since I always go to press Fn-Right and not get what I want. The tool suggested in the other question is Sharpkeys, however it doesn't recognise Fn+Right as a different key from Right, and I suspect that registry twiddling isn't going to help me here. (?) Is there any way to remap this combination? (I'm on Windows Vista if that helps)

Read the article
Remove Windows 7's limitation on number of concurrent tcp connections (http web requests)

- by Ghita

I have an application that tries to open as many http requests as possible (in order to stress test a proxy implementation) It seems to me that Win7 (SP1) may have a limitation on number of concurrent opened connection (it may be the so called half-open state if I'm not wrong). Is there something I can do for client ? and also I test using a vista PC that acts as a proxy server. It would be great if I could configure it to sustain at least 50 new connections initiated / second on client side and many more on server. I made the modification according to this technet article by setting TcpNumConnections = 150 but it doesn't make a difference. I still only see about 20 tcp sockets associated with my http client by using tcpview.

Read the article
Windows 7 + NVidia == 640x480 on external projectors

- by ben2004uk

Hello, I'm having a major problem and I really need your help! I have a MacBook Air which has the NVidia 9400M. The problem is, when I connect it to an external projector Windows 7 (and Vista) only allow me to connect at 640x480. I need it to use the laptop to present at conferences, as such I need it to work on a number of different projectors - at the moment I need to use OSX and VMWare but it's painfully slow and really doesn't work. At the moment, I'm considering buying a new laptop :( Is there any way to override the screen resolutions provided? I've saw some information around EDID? Thanks Ben

Read the article
USB Drive cannot detect in Windows 7

- by Perdana Putra

Have you ever plugged in a USB drive or any external device with a hard drive and wondered why you cannot see it in My Computer? I often have, I believe my USB is not broke .. because if I plugin the USB to another computer could be seen / detected. I tried following this tutorial http://www.howtogeek.com/howto/22251/find-your-missing-usb-drive-in-windows-7-vista/ but I am afraid of going wrong, and caused my data is lost. is there any easy way around this problem? many thank's for your attentions Guys ..

Read the article
Moving to an SSD with Windows 7

- by Nick Gerakines

Disclaimer: I've been digging around for a few days and didn't get what I was looking for in terms of answers, so I'm asking here. I've recently purchased an 80g SSD drive to use as my boot up and OS parition. I've got a windows 7 desktop with two 1TB (raid0) disks currently and I'm not sure where to start in terms of copying / moving the OS. I suppose that doing a fresh install isn't out of the question, but I've got an upgrade disk from Vista that I'd have to deal with. Where do I begin?

Read the article
Windows Server: specifying the default IP address when NIC has multiple addresses

- by Cédric Boivin

I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008, I've had the same problem with a Windows Server 2003. How can you set the default IP address on a NIC when it has multiple IP addresses bound? I remark something. When i check route print i see is it there the problem ? 0.0.0.0 0.0.0.0 192.168.x.x 192.168.99.49 261 if i want the default ip be example : 192.168.99.100 There is my route. Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 I need to be certain, when i go on internet i go with the 192.168.99.100 how i do that ?

Read the article
Windows Server: specifying the default IP address when NIC has multiple addresses

- by Cédric Boivin

I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008, I've had the same problem with a Windows Server 2003. How can you set the default IP address on a NIC when it has multiple IP addresses bound? I remark something. When i check route print i see is it there the problem ? 0.0.0.0 0.0.0.0 192.168.x.x 192.168.99.49 261 if i want the default ip be example : 192.168.99.100 There is my route. Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 I need to be certain, when i go on internet i go with the 192.168.99.100 how i do that ?

Read the article
Mount points disappear from network share directory listing

- by Barakando

When browsing a network share which contains volume mount points, said mount points disappear from the directory listing. The mount points are still accessible directly by path, just not present in the directory listing. The machine is a Vista SP1 32 bit machine. It has a network share that contains volume mount points to the volumes of the Vista machine (created using the SetVolumeMountPoint API). When browsing the network share from another computer (either Win7 64 bit, Win7 32 bit or Vista SP1 32 bit) using Windows Explorer the following problem occurs: First, both volume mount points called C, D appear fine. I browse into directory C and see all its contents properly. I go back to the root of the shared folder and now I only see D. C has disappeared from the directory listing. I enter D and see all its contents. Go back to the root of the shared folder and now it's empty. D disappeared as well. If I manually go to \\<path to shared folder>\C from the address bar - then all is fine and I can browse its contents (same with D). The same issue does NOT occur when creating a similar share with volume mount points on Windows XP SP2 or SP3. Has anyone came across this problem? Any ideas how to work around it?

Read the article
Windows 2008 Unknown Disks

- by Ailbe

I have a BL460c G7 blade server with OS Windows 2008 R2 SP1. This is a brand new C7000 enclosure, with FlexFabric interconnects. I got my FC switches setup and zoned properly to our Clariion CX4, and can see all the hosts that are assigned FCoE HBAs on both paths in both Navisphere and in HP Virtual Connect Manager. So I went ahead and created a storage group for a test server, assigned the appropriate host, assigned the LUN to the server. So far so good, log onto server and I can see 4 unknown disks.... No problem, I install MS MPIO, no luck, can't initialize the disks, and the multiple disks don't go away. Still no problem, I install PowerPath version 5.5 reboot. Now I see 3 disks. One is initialized and ready to go, but I still have 2 disks that I can't initialize, can't offline, can't delete. If I right click in storage manager and go to properties I can see that the MS MPIO tab, but I can't make a path active. I want to get rid of these phantom disks, but so far nothing is working and google searches are showing up some odd results, so obviously I'm not framing my question right. I thought I'd ask here real quick. Does anyone know a quick way to get rid of these unknown disks. Another question, do I need the MPIO feature installed if I have PowerPath installed? This is my first time installing Windows 2008 R2 in this fashion and I'm not sure if that feature is needed or not right now. So some more information to add to this. It seems I'm dealing with more of a Windows issue than anything else. I removed the LUN from the server, uninstalled PowerPath completely, removed the MPIO feature from the server, and rebooted twice. Now I am back to the original 4 Unknown Disks (plus the local Disk 0 containing the OS partition of course, which is working fine) I went to diskpart, I could see all 4 Unknown disks, I selected each disk, ran clean (just in case i'd somehow brought them online previously as GPT and didn't realize it) After a few minutes I was no longer able to see the disks when I ran list disk. However, the disks are still in Disk Management. When I try and offline the disks from Disk Management I get an error: Virtual Disk Manager - The system cannot find the file specified. Accompanied by an error in System Event Logs: Log Name: System Source: Virtual Disk Service Date: 6/25/2012 4:02:01 PM Event ID: 1 Task Category: None Level: Error Keywords: Classic User: N/A Computer: hostname.local Description: Unexpected failure. Error code: 2@02000018 Event Xml: 1 2 0 0x80000000000000 4239 System hostname.local 2@02000018 I feel sure there is a place I can go in the Registry to get rid of these, I just can't recall where and I am loathe to experiement. So to recap, there are currently no LUNS attached at all, I still have the phantom disks, and I'm getting The system cannot find the file specified from Virtual Disk Manager when I try to take them offline. Thanks!

Read the article
Laptop sleep: How to go into S3 easily?

- by monov

Laptop: Fujitsu-Siemens Amilo Pi-3525 OS: Vista When my laptop is plugged in and I close the lid, it goes into S1 sleep. This means that there is still: fan noise (annoying when trying to sleep at night) lots of power consumed (so if I then unplug the laptop and toss it in the bag, by the time I'm at school it's already drained and beeping ominously). What I want is S3 sleep, it solves both problems. I've found a roundabout way to go into S3 sleep: Unplug laptop Close lid (or click Sleep in Start menu) Plug laptop back in if needed The question: How do I force Windows to use always use S3 sleep when I close the lid? One thing I've tried is: dumppo admin minsleep=s3 (dumppo from here) Afterwards running just dumppo admin confirms that minsleep has been set, but closing the lid still goes into S1. Also, after a reboot, minsleep is reset to s1. I think dumppo is incompatible with Vista... MCE Standby Tool was recommended as a Vista-compatible alternative to dumppo, but it doesn't have any effect either. I looked in the BIOS settings, but there are no settings relating to ACPI sleeps/suspends there.

Read the article
Windows 7 sometimes boots in VGA mode

- by TuxRug

I have an Asus G50VT-x5 laptop with nVidia GeForce9800M-GS graphics. Normally, Windows boots normally, but about 20% of the time (rough estimate), it will boot with the fallback VGA driver, maxing out at 800x600 with no Aero. I've checked the system logs and there is nothing indicating an error loading the nVidia driver. It even specifies in the logs that the Nvidia Display Driver service started successfully, even though it has booted in safe graphics mode. This has been happening for a while, but it's happening a little more often now than it was before. Since the first time my system exhibited this behavior, I have updated my graphics driver a handful of times. I used System Information for Windows to check for problems there, but the only thing that stood out was the following: Core Temperature 4486449 °C (8075639 °F) Shaders Temperature 1171513530 °C (2108724330 °F) I know this reading is incorrect, because my laptop is nowhere near the surface of the sun and my desk has not burst into flames. When it's opererating normally, I get a sane reading like [Core Temperature 58 °C (136 °F)] with no Shaders Temperature listed. All I have to do to resolve the issue is reboot. I have seen no stability issues with the graphics or anything else. A long time ago, I had an issue with this computer where my framerate would suddenly drop during a 3D game from 40fps to <1fps, but after looking at the temperature readout immediately after quitting a game, I removed the bottom panel and blew the dust out of the vent and heatsink. Since then I have no drops in framerate under any situation. I have uploaded a zip containing the SIW reports for when the problem is occurring and when the computer is operating normally. I don't have a paid account so it can only be downloaded 10 times, so please only download the reports if you think you can use them. If you try to download the reports and they are no longer available, please comment and I will re-upload them. If you want to look at the files, they are on Rapidshare. EDIT It happened again, and I looked a little deeper into the System logs. When this happens, there are a lot of errors about other device drivers unable to start. All of these errors are for PnP drivers. Also, my USB keyboard and mouse take a few moments before they actually start working, although this happens sometimes the first normal boot as well. I am quite sure this is related, so I am adding the pnp tag. Also, CHKDSK will not run on boot. Even if a check is scheduled or a volume is manually set as dirty, CHKDSK will be skipped entirely, not even leaving an entry in the System logs. I tried running CHKNTFS /D, which did not work. I then manually changed my HKLM\System\CurrentControlSet\Control\Session Manager BootExecute value to the default listed on Microsoft's website. That did not work either. I ended up booting to repair mode and running CHKDSK there, which found a number of minor inconsistencies on my system drive, but none on my data drive. I have no idea if this is related. Some more information for those who don't download my SIW report file: Antivirus and Firewall are ESET Smart Security I have three different virutalization programs installed: VMware Player, Windows Virtual PC, and VirtualBox. The network adapters for these show up in the log of failed device starts. EDIT 2 I tried running sfc /scannow, which reported that it found corrupted files that could not be fixed. The CBS log is extremely cryptic. I tried booting to my install disk, launching repair mode, and doing an offline sfc from there, which produced the same result.

Read the article
Windows 8 Stuck on Start Screen File Search

- by baturayd

I have been searching someone else having the same issue but I couldn't find any. Here is my problem: I'm using Windows 8 Pro with Media Center. File search screen does not close itself after I make a file search within start screen. It stuck on that screen. I can't go back to desktop, therefore, task manager is inaccessible. Only way to get out of it is to sign out. It also looks like non-operational. It doesn't give me any result at all. It's just a blank screen with "Files" title. It used to work perfectly. Things I have done before coming here: Safe mode minimal boot to ensure no other 3rd party software interferes. sfc haven't found any inconsistencies. Search index has been rebuild. Normal boot with all 3rd party services and start-up items disabled. System restore to a date that I know this feature was functional. And by the way, I have installed all updates released so far. I strongly used file search via start menu back in Windows 7. This is an absolute game changer for me. I'm curious what causes this. I'll do a "system refresh" if I can't fix this. I'm working on it, I'll keep this thread updated should I find any fix. First update: I just discovered that file search screen gets stuck if it's invoked by typing query directly in start screen. It doesn't get stuck if it's invoked from win + x menu. I was able to "escape" from stuck screen with invoking it again by win + x menu. After rebuilding search index again, search suggestions started to appear again but still there is no file search functionality. Second update: "Results for" expression appears only for a second near to "Files" title when search is initialized. Third update: As a last resort, I finally tried to do a "System Refresh" which has also failed to refresh by giving an error after waiting almost 20 minutes at 99%. (Seriously?) After cold boot it began to undo changes. After changes were reverted, I boot the machine without doing anything further and bingo! Search began acting normal again. This is a totally weird solution. It obviously fixed certain system files during failed refresh, and kept those changes untouched because they were supposed to be that way at the first place. I'll keep this thread alive should anyone comes with a more logical explanation. Forth update: After a windows update, search functionality again stopped responding. It happened after a system update for the first time. Now I have a pretty good suspicion about system update, though I have no solid proof of its involvement with this problem.

Read the article
Move "XP Mode" from Windows Virtual PC to VirtualBox?

- by JoelFan

I installed "XP Mode" in Windows 7 (which uses Windows Virtual PC to host XP). I have now discovered that VirtualBox, which I have installed on the same Windows 7 machine, refuses to run at the same time as Windows Virtual PC (it gives me an error about not running multiple visualization programs). Is there any way I can convert the "XP Mode" image so that it will run inside VirtualBox instead of Windows Virtual PC? That way I will be able to run XP as well as other VM's at the same time.

Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306 | Next Page >