Search Results

Search found 126 results on 6 pages for 'aren cambre'.

Page 3/6 | < Previous Page | 1 2 3 4 5 6  | Next Page >

• How to Tell a Hardware Problem From a Software Problem

  - by Chris Hoffman

  Your computer seems to be malfunctioning — it’s slow, programs are crashing or Windows may be blue-screening. Is your computer’s hardware failing, or does it have a software problem that you can fix on your own? This can actually be a bit tricky to figure out. Hardware problems and software problems can lead to the same symptoms — for example, frequent blue screens of death may be caused by either software or hardware problems. Computer is Slow We’ve all heard the stories — someone’s computer slows down over time because they install too much software that runs at startup or it becomes infected with malware. The person concludes that their computer is slowing down because it’s old, so they replace it. But they’re wrong. If a computer is slowing down, it has a software problem that can be fixed. Hardware problems shouldn’t cause your computer to slow down. There are some rare exceptions to this — perhaps your CPU is overheating and it’s downclocking itself, running slower to stay cooler — but most slowness is caused by software issues. Blue Screens Modern versions of Windows are much more stable than older versions of Windows. When used with reliable hardware with well-programmed drivers, a typical Windows computer shouldn’t blue-screen at all. If you are encountering frequent blue screens of death, there’s a good chance your computer’s hardware is failing. Blue screens could also be caused by badly programmed hardware drivers, however. If you just installed or upgraded hardware drivers and blue screens start, try uninstalling the drivers or using system restore — there may be something wrong with the drivers. If you haven’t done anything with your drivers recently and blue screens start, there’s a very good chance you have a hardware problem. Computer Won’t Boot If your computer won’t boot, you could have either a software problem or a hardware problem. Is Windows attempting to boot and failing part-way through the boot process, or does the computer no longer recognize its hard drive or not power on at all? Consult our guide to troubleshooting boot problems for more information. When Hardware Starts to Fail… Here are some common components that can fail and the problems their failures may cause: Hard Drive: If your hard drive starts failing, files on your hard drive may become corrupted. You may see long delays when you attempt to access files or save to the hard drive. Windows may stop booting entirely. CPU: A failing CPU may result in your computer not booting at all. If the CPU is overheating, your computer may blue-screen when it’s under load — for example, when you’re playing a demanding game or encoding video. RAM: Applications write data to your RAM and use it for short-term storage. If your RAM starts failing, an application may write data to part of the RAM, then later read it back and get an incorrect value. This can result in application crashes, blue screens, and file corruption. Graphics Card: Graphics card problems may result in graphical errors while rendering 3D content or even just while displaying your desktop. If the graphics card is overheating, it may crash your graphics driver or cause your computer to freeze while under load — for example, when playing demanding 3D games. Fans: If any of the fans fail in your computer, components may overheat and you may see the above CPU or graphics card problems. Your computer may also shut itself down abruptly so it doesn’t overheat any further and damage itself. Motherboard: Motherboard problems can be extremely tough to diagnose. You may see occasional blue screens or similar problems. Power Supply: A malfunctioning power supply is also tough to diagnose — it may deliver too much power to a component, damaging it and causing it to malfunction. If the power supply dies completely, your computer won’t power on and nothing will happen when you press the power button. Other common problems — for example, a computer slowing down — are likely to be software problems. It’s also possible that software problems can cause many of the above symptoms — malware that hooks deep into the Windows kernel can cause your computer to blue-screen, for example. The Only Way to Know For Sure We’ve tried to give you some idea of the difference between common software problems and hardware problems with the above examples. But it’s often tough to know for sure, and troubleshooting is usually a trial-and-error process. This is especially true if you have an intermittent problem, such as your computer blue-screening a few times a week. You can try scanning your computer for malware and running System Restore to restore your computer’s system software back to its previous working state, but these aren’t  guaranteed ways to fix software problems. The best way to determine whether the problem you have is a software or hardware one is to bite the bullet and restore your computer’s software back to its default state. That means reinstalling Windows or using the Refresh or reset feature on Windows 8. See whether the problem still persists after you restore its operating system to its default state. If you still see the same problem – for example, if your computer is blue-screening and continues to blue-screen after reinstalling Windows — you know you have a hardware problem and need to have your computer fixed or replaced. If the computer crashes or freezes while reinstalling Windows, you definitely have a hardware problem. Even this isn’t a completely perfect method — for example, you may reinstall Windows and install the same hardware drivers afterwards. If the hardware drivers are badly programmed, the blue-screens may continue. Blue screens of death aren’t as common on Windows these days — if you’re encountering them frequently, you likely have a hardware problem. Most blue screens you encounter will likely be caused by hardware issues. On the other hand, other common complaints like “my computer has slowed down” are easily fixable software problems. When in doubt, back up your files and reinstall Windows. Image Credit: Anders Sandberg on Flickr, comedy_nose on Flickr     

  Read the article

• Tips To Manage An Effectively Come Back To Work After A Long Vacation

  - by Gopinath

  Vacations are very relaxing – no need to reply to endless mails, no marathon meeting or conference calls. It’s all about fun during the vacation. The troubles begin as you near the end of vacation and plans to think about getting back to work. Once we are back to work after a long vacation there will be many things to worry – a pile of snail mails, hundreds of unread emails,  a flood of phone calls to answer and a stream of scheduled meetings. How to handle all the backlog and catch up quickly with the inflow of work? Here is a management tip from Harvard Business Review blog to get back to work the right way after a long vacation Block off your morning. Make sure you don’t have any meetings scheduled or big projects due. Then before you open your inbox, pause and think about your work priorities. As you make your way through emails and voicemails, focus on returning the messages that are connected to what matters most. Defer or delegate things that aren’t top priority. And remember it will probably take more than one day to get caught up, so be easy on yourself. Hope these tips lets you plan a right comeback to work after your vacation. cc Image credit: flickr/dfwcre8tive This article titled,Tips To Manage An Effectively Come Back To Work After A Long Vacation, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• Not All “Viruses” Are Viruses: 10 Malware Terms Explained

  - by Chris Hoffman

  Most people seem to call every type of malware a “virus”, but that isn’t technically accurate. You’ve probably heard of many more terms beyond virus: malware, worm, Trojan, rootkit, keylogger, spyware, and more. But what do all these terms mean? These terms aren’t just used by geeks. They make their way into even mainstream news stories about the latest web security problems and tech scares. Understanding them will help you understand the dangers your\ hear about. Malware The word “malware” is short for “malicious software.” Many people use the word “virus” to indicate any type of harmful software, but a virus is actually just a specific type of malware. The word “malware” encompasses all harmful software, including all the ones listed below. Virus Let’s start with viruses. A virus is a type of malware that copies itself by infecting other files,  just as viruses in the real world infect biological cells and use those biological cells to reproduce copies of themselves. A virus can do many different things — watch in the background and steal your passwords, display advertisements, or just crash your computer — but the key thing that makes it a virus is how it spreads. When you run a virus, it will infect programs on your computer. When you run the program on another computer, the virus will infect programs on that computer, and so on. For example, a virus might infect program files on a USB stick. When the programs on that USB stick are run on another computer, the virus runs on the other computer and infects more program files. The virus will continue to spread in this way. Worm A worm is similar to a virus, but it spreads a different way. Rather than infecting files and relying on human activity to move those files around and run them on different systems, a worm spreads over computer networks on its own accord. For example, the Blaster and Sasser worms spread very quickly in the days of Windows XP because Windows XP did not come properly secured and exposed system services to the Internet. The worm accessed these system services over the Internet, exploited a vulnerability, and infected the computer. The worm then used the new infected computer to continue replicating itself. Such worms are less common now that Windows is properly firewalled by default, but worms can also spread in other ways — for example, by mass-emailing themselves to every email address in an effected user’s address book. Like a virus, a worm can do any number of other harmful things once it infects a computer. The key thing that makes it a worm is simply how it spreads copies of itself. Trojan (or Trojan Horse) A Trojan horse, or Trojan, is a type of malware that disguises itself as a legitimate file. When you download and run the program, the Trojan horse will run in the background, allowing third-parties to access your computer. Trojans can do this for any number of reasons — to monitor activity on your computer, to join your computer to a botnet. Trojans may also be used to open the floodgates and download many other types of malware onto your computer. The key thing that makes this type of malware a Trojan is how it arrives. It pretends to be a useful program and, when run, it hides in the background and gives malicious people access to your computer. It isn’t obsessed with copying itself into other files or spreading over the network, as viruses and worms are. For example, a piece of pirated software on an unscrupulous website may actually contain a Trojan. Spyware Spyware is a type of malicious software that spies on you without your knowledge. It collects a variety of different types of data, depending on the piece of spyware. Different types of malware can function as spyware — there may be malicious spyware included in Trojans that spies on your keystrokes to steal financial data, for example. More “legitimate” spyware may be bundled along with free software and simply monitor your web browsing habits, uploading this data to advertising servers so the software’s creator can make money from selling their knowledge of your activities. Adware Adware often comes along with spyware. It’s any type of software that displays advertising on your computer. Programs that display advertisements inside the program itself aren’t generally classified as malware. The kind of “adware” that’s particularly malicious is the kind that abuses its access to your system to display ads when it shouldn’t. For example, a piece of harmful adware may cause pop-up advertisements to appear on your computer when you’re not doing anything else. Or, adware may inject additional advertising into other web pages as you browse the web. Adware is often combined with spyware — a piece of malware may monitor your browsing habits and use them to serve you more targeted ads. Adware is more “socially acceptable” than other types of malware on Windows and you may see adware bundled with legitimate programs. For example, some people consider the Ask Toolbar included with Oracle’s Java software adware. Keylogger A keylogger is a type of malware that runs in the background, recording every key stroke you make. These keystrokes can include usernames, passwords, credit card numbers, and other sensitive data. The keylogger then, most likely, uploads these keystrokes to a malicious server, where it can be analyzed and people can pick out the useful passwords and credit card numbers. Other types of malware can act as keyloggers. A virus, worm, or Trojan may function as a keylogger, for example. Keyloggers may also be installed for monitoring purposes by businesses or even jealous spouses. Botnet, Bot A botnet is a large network of computers that are under the botnet creator’s control. Each computer functions as a “bot” because it’s infected with a specific piece of malware. Once the bot software infects the computer, ir will connect to some sort of control server and wait for instructions from the botnet’s creator. For example, a botnet may be used to initiate a DDoS (distributed denial of service) attack. Every computer in the botnet will be told to bombard a specific website or server with requests at once, and such millions or requests can cause a server to become unresponsive or crash. Botnet creators may sell access to their botnets, allowing other malicious individuals to use large botnets to do their dirty work. Rootkit A rootkit is a type of malware designed to burrow deep into your computer, avoiding detection by security programs and users. For example, a rootkit might load before most of Windows, burying itself deep into the system and modifying system functions so that security programs can’t detect it. A rootkit might hide itself completely, preventing itself from showing up in the Windows task manager. The key thing that makes a type of malware a rootkit is that it’s stealthy and focused on hiding itself once it arrives. Ransomware Ransomware is a fairly new type of malware. It holds your computer or files hostage and demands a ransom payment. Some ransomware may simply pop up a box asking for money before you can continue using your computer. Such prompts are easily defeated with antivirus software. More harmful malware like CryptoLocker literally encrypts your files and demands a payment before you can access them. Such types of malware are dangerous, especially if you don’t have backups. Most malware these days is produced for profit, and ransomware is a good example of that. Ransomware doesn’t want to crash your computer and delete your files just to cause you trouble. It wants to take something hostage and get a quick payment from you. So why is it called “antivirus software,” anyway? Well, most people continue to consider the word “virus” synonymous with malware as a whole. Antivirus software doesn’t just protect against viruses, but against all types of malware. It may be more accurately referred to as “antimalware” or “security” software. Image Credit: Marcelo Alves on Flickr, Tama Leaver on Flickr, Szilard Mihaly on Flickr     

  Read the article

• OpenFilesView Displays All Open and Locked Files to Help Resolve In-Use Errors

  - by Jason Fitzpatrick

  Windows: You go to move a file and Windows throws up an “In Use” error. OpenFilesView shows you what application or system process is locking up the files you’re trying to move. Sometimes the culprit is obvious; if you go to move your media folder and you’ve got your media player open watching South Park then shutting down the media player is the obvious solution. Other times the culprit is less obvious; sometimes Windows processes and less-than-obvious applications are accessing your files in ways that aren’t apparent. The screenshot below showcases the “In Use” error: This is where OpenFilesView comes into play. Fire up the application to see a list of all active files on your system. The master list is a bit overwhelming (on our test system there were over 1200 open files) but you use the find command to drill down to specific file or folder names. Once you’ve found the locked file you can close the file handle, kill the process, or bring the process to the front (so you can examine the program, if possible, before terminating it). It’s much more efficient than rebooting in an attempt to shake the In-Use error. OpenFilesView is freeware and works on Windows XP through Windows 7. HTG Explains: Do You Really Need to Defrag Your PC? Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive

  Read the article

• HTG Explains: Do Non-Windows Platforms Like Mac, Android, iOS, and Linux Get Viruses?

  - by Chris Hoffman

  Viruses and other types of malware seem largely confined to Windows in the real world. Even on a Windows 8 PC, you can still get infected with malware. But how vulnerable are other operating systems to malware? When we say “viruses,” we’re actually talking about malware in general. There’s more to malware than just viruses, although the word virus is often used to talk about malware in general. Why Are All the Viruses For Windows? Not all of the malware out there is for Windows, but most of it is. We’ve tried to cover why Windows has the most viruses in the past. Windows’ popularity is definitely a big factor, but there are other reasons, too. Historically, Windows was never designed for security in the way that UNIX-like platforms were — and every popular operating system that’s not Windows is based on UNIX. Windows also has a culture of installing software by searching the web and downloading it from websites, whereas other platforms have app stores and Linux has centralized software installation from a secure source in the form of its package managers. Do Macs Get Viruses? The vast majority of malware is designed for Windows systems and Macs don’t get Windows malware. While Mac malware is much more rare, Macs are definitely not immune to malware. They can be infected by malware written specifically for Macs, and such malware does exist. At one point, over 650,000 Macs were infected with the Flashback Trojan. [Source] It infected Macs through the Java browser plugin, which is a security nightmare on every platform. Macs no longer include Java by default. Apple also has locked down Macs in other ways. Three things in particular help: Mac App Store: Rather than getting desktop programs from the web and possibly downloading malware, as inexperienced users might on Windows, they can get their applications from a secure place. It’s similar to a smartphone app store or even a Linux package manager. Gatekeeper: Current releases of Mac OS X use Gatekeeper, which only allows programs to run if they’re signed by an approved developer or if they’re from the Mac App Store. This can be disabled by geeks who need to run unsigned software, but it acts as additional protection for typical users. XProtect: Macs also have a built-in technology known as XProtect, or File Quarantine. This feature acts as a blacklist, preventing known-malicious programs from running. It functions similarly to Windows antivirus programs, but works in the background and checks applications you download. Mac malware isn’t coming out nearly as quick as Windows malware, so it’s easier for Apple to keep up. Macs are certainly not immune to all malware, and someone going out of their way to download pirated applications and disable security features may find themselves infected. But Macs are much less at risk of malware in the real world. Android is Vulnerable to Malware, Right? Android malware does exist and companies that produce Android security software would love to sell you their Android antivirus apps. But that isn’t the full picture. By default, Android devices are configured to only install apps from Google Play. They also benefit from antimalware scanning — Google Play itself scans apps for malware. You could disable this protection and go outside Google Play, getting apps from elsewhere (“sideloading”). Google will still help you if you do this, asking if you want to scan your sideloaded apps for malware when you try to install them. In China, where many, many Android devices are in use, there is no Google Play Store. Chinese Android users don’t benefit from Google’s antimalware scanning and have to get their apps from third-party app stores, which may contain infected copies of apps. The majority of Android malware comes from outside Google Play. The scary malware statistics you see primarily include users who get apps from outside Google Play, whether it’s pirating infected apps or acquiring them from untrustworthy app stores. As long as you get your apps from Google Play — or even another secure source, like the Amazon App Store — your Android phone or tablet should be secure. What About iPads and iPhones? Apple’s iOS operating system, used on its iPads, iPhones, and iPod Touches, is more locked down than even Macs and Android devices. iPad and iPhone users are forced to get their apps from Apple’s App Store. Apple is more demanding of developers than Google is — while anyone can upload an app to Google Play and have it available instantly while Google does some automated scanning, getting an app onto Apple’s App Store involves a manual review of that app by an Apple employee. The locked-down environment makes it much more difficult for malware to exist. Even if a malicious application could be installed, it wouldn’t be able to monitor what you typed into your browser and capture your online-banking information without exploiting a deeper system vulnerability. Of course, iOS devices aren’t perfect either. Researchers have proven it’s possible to create malicious apps and sneak them past the app store review process. [Source] However, if a malicious app was discovered, Apple could pull it from the store and immediately uninstall it from all devices. Google and Microsoft have this same ability with Android’s Google Play and Windows Store for new Windows 8-style apps. Does Linux Get Viruses? Malware authors don’t tend to target Linux desktops, as so few average users use them. Linux desktop users are more likely to be geeks that won’t fall for obvious tricks. As with Macs, Linux users get most of their programs from a single place — the package manager — rather than downloading them from websites. Linux also can’t run Windows software natively, so Windows viruses just can’t run. Linux desktop malware is extremely rare, but it does exist. The recent “Hand of Thief” Trojan supports a variety of Linux distributions and desktop environments, running in the background and stealing online banking information. It doesn’t have a good way if infecting Linux systems, though — you’d have to download it from a website or receive it as an email attachment and run the Trojan. [Source] This just confirms how important it is to only run trusted software on any platform, even supposedly secure ones. What About Chromebooks? Chromebooks are locked down laptops that only run the Chrome web browser and some bits around it. We’re not really aware of any form of Chrome OS malware. A Chromebook’s sandbox helps protect it against malware, but it also helps that Chromebooks aren’t very common yet. It would still be possible to infect a Chromebook, if only by tricking a user into installing a malicious browser extension from outside the Chrome web store. The malicious browser extension could run in the background, steal your passwords and online banking credentials, and send it over the web. Such malware could even run on Windows, Mac, and Linux versions of Chrome, but it would appear in the Extensions list, would require the appropriate permissions, and you’d have to agree to install it manually. And Windows RT? Microsoft’s Windows RT only runs desktop programs written by Microsoft. Users can only install “Windows 8-style apps” from the Windows Store. This means that Windows RT devices are as locked down as an iPad — an attacker would have to get a malicious app into the store and trick users into installing it or possibly find a security vulnerability that allowed them to bypass the protection. Malware is definitely at its worst on Windows. This would probably be true even if Windows had a shining security record and a history of being as secure as other operating systems, but you can definitely avoid a lot of malware just by not using Windows. Of course, no platform is a perfect malware-free environment. You should exercise some basic precautions everywhere. Even if malware was eliminated, we’d have to deal with social-engineering attacks like phishing emails asking for credit card numbers. Image Credit: stuartpilbrow on Flickr, Kansir on Flickr     

  Read the article

• Developers are strange

  - by DavidWimbush

  Why do developers always use the GUI tools in SQL Server? I've always found this irritating and just vaguely assumed it's because they aren't familiar with SQL syntax. But when you think about it it, it's a genuine puzzle. Developers type code all day - really heavy code too like generics, lamda functions and extension methods. They (thankfully) scorn the Visual Studio stuff where you drag a table onto the class and it pastes in lots of code to query the table into a DataSet or something. But when they want to add a column to a table, without fail they dive into the graphical table designer. And half the time the script it generates does horrible things like copy the table to another one with the new column, delete the old table, and rename the new table. Which is fine if your users don't care about uptime. Is ALTER TABLE ADD <column definition> really that hard? I just don't get it.

  Read the article

• links for 2010-06-09

  - by Bob Rhubart

  Enterprise Architecture: From Incite comes Insight...: Why aren't we seeing more adoption of open source in large enterprises? (tags: ping.fm entarch opensource linux) Forms Modernization, Part 1: Motivation for change iAdvise blog (tags: ping.fm oracleace apex middleware oracle) OmniGraffle for iPad Now Supports VGA Output (Enterprise Architecture at Oracle) (tags: ping.fm entarch ipad oracle) SysAdmin access in Oracle VDI - Jaap's VDI Blog Space (tags: ping.fm virtualization sunray vdi) Securing Enterprise Data in AWS Oracle PeopleSoft Enterprise Consulting, Support and Training (tags: ping.fm cloud peoplesoft entarch) Enterprise Software Development with Java: ODTUG Kaleidoscope 2010 - preparations and sessions (tags: ping.fm oracle java oracleace) @toddbiske: Enterprise Architecture Must Assist Delivery "In most IT organizations, things get delivered through projects, and enterprise architects don’t typically play the role of project architect. At best, there is an indirect association with delivery." -- Todd Biske (tags: entarch enterprisearchitecture) @pevansgreenwood: The Rules of Enterprise IT "The rules of this game need to change if enterprise IT — as we know it — is to remain relevant in the future." -- Peter Evans Greenwood (tags: entarch enterprisearchitecture) @bex: Oracle UCM 11g Now Released! "Good news!" says Oracle ACE Director Bex Huff. "The 11g version of Oracle UCM is finally available! This version is a bit of a re-write to run on top of the WebLogic application server. Oracle has been talking about this release for some time, so I'm glad to see it finally available." (tags: oracle enteprise2.0 e20 oracleace) Marc Kelderman: SOA 11g Cloning Cloning an Oracle SOA Suite 11g environment is rather simple. Marc Kelderman shows you how. (tags: soa oracle)

  Read the article

• HTG Explains: Just How Bad Are Android Tablet Apps?

  - by Chris Hoffman

  Apple loves to criticize the state of Android tablet apps when pushing its own iPad tablets. But just how bad is the Android tablet app situation? Should you avoid Android tablets like the Nexus 7 because of the apps? It’s clear that Apple’s iPad is way ahead when it comes to the sheer quantity of tablet-optimized apps. It’s also clear that some popular apps — particularly touch-optimized games — only show up on iPad. But that’s not the whole story. The Basics First, let’s get an idea of the basic stuff that will work well for you on Android. An excellent web browser. Chrome has struggled with performance on Android, but hits its stride on the Nexus 7 (2013). Great, tablet-optimized apps for all of Google’s services, from YouTube to Gmail and Google Maps. Everything you need for reading, from Amazon’s Kindle app for eBooks, Flipboard and Feedly for new articles from websites, and other services like the popular Pocket read-it-later service. Apps for most popular media services, from Netflix, Hulu, and YouTube for videos to Pandora, Spotify, and Rdio for music. A few things aren’t available — you won’t find Apple’s iTunes and Amazon still doesn’t offer an Amazon Instant Video app for Android, while they do for iPad and even their own Android-based Kindle Fire devices. Android has very good app coverage when it comes to consuming content, whether you’re reading websites and ebooks or watching videos and listening to music. You can play almost any Android smartphone game, too. For content consumption, Android is better than something like Windows 8, which lacks apps for Google services like YouTube and still doesn’t have apps for popular media services like Spotify and Rdio. How Android Scales Smartphone Apps Let’s look at how Android scales smartphone apps. Now, bear with us here — we know “scaling” is a dirty word considering how poorly Apple’s iPad scales iPhone apps, but it’s not as bad on Android. When an iPad runs an iPhone app, it simply doubles the pixels and effectively zooms in. For example, if you had  Twitter app with five tweets visible at once on an iPhone and ran the same app on an iPad, the iPad would simply “zoom in” and enlarge the same screen — you’d still see five tweets, but each tweet would appear larger. This is why developers create optimized iPad apps with their own interfaces. It’s especially important on Apple’s iOS. Android devices come in all shapes and sizes, so Android apps have a smarter, more intelligent way to adapt to different screen sizes. Let’s say you have a Twitter app designed for smartphones and it only shows five tweets at once when run on a phone. If you ran the same app on a tablet, you wouldn’t see the same five tweets — you’d see ten or more tweets. Rather than simply zooming in, the app can show more content at the same time on a tablet, even if it was never optimized for tablet-size screens. While apps designed for smartphones aren’t generally ideal, they adapt much better on Android than they do on an iPad. This is particularly true when it comes to games. You’re capable of playing almost any Android smartphone game on an Android tablet, and games generally adapt very well to the larger screen. This gives you access to a huge catalog of games. It’s a great option to have, especially when you look at Microsoft’s Window 8 and consider how much better the touch-based app and game selection would be if Microsoft allowed its users to run Windows Phone games on Windows 8. 7-inch vs 10-inch Tablets The Twitter example above wasn’t just an example. The official Twitter app for Android still doesn’t have a tablet-optimized interface, so this is the sort of situation you’d have to deal with on an Android tablet. On the popular Nexus 7, Twitter is an example of a smartphone app that actually works fairly well — in portrait mode, you can see many more tweets on screen at the same time and none of the space really feels all that wasted. This is important to consider — smartphone apps like Twitter often scale quite well to 7-inch screens because a 7-inch screen is much closer in form factor to a smartphone than a 10-inch screen is. When you begin to look at 10-inch Android tablets that are the same size as an iPad, the situation changes. While the Twitter app works well enough on a Nexus 7, it looks horrible on a Nexus 10 or other 10-inch tablet. Running many smartphone-designed apps — possible with the exception of games — on a 10-inch tablet is a frustrating, poor experience. There’s much more white, empty space in the interface. It feels like you’re using a smartphone app on a large screen, and what’s the point of that? A tablet-optimized Twitter app for Android is finally on its way, but this same situation will repeat with many other types of apps. For example, Facebook doesn’t offer a tablet-optimized interface, but it’s okay on a Nexus 7 anyway. On a 10-inch screen, it probably wouldn’t be anywhere near as nice an experience. It goes without saying that Facebook and Twitter both offer iPad apps with interfaces designed for a tablet-size screen. Here’s another problematic app — the official Yelp app for Android. Even just using it on a 7-inch Nexus 7 will be a poor experience, while it would be much worse on a larger 10-inch tablet app. Now, it’s true that many — maybe even most — of the popular apps you might want to run today are optimized for Android tablets. But, when you look at the situation when it comes to popular apps like Twitter, Facebook, and Yelp, it’s clear Android is still behind in a meaningful way. Price Let’s be honest. The thing that really makes Android tablets compelling — and the only reason Android tablets started seeing real traction after years of almost complete dominance by Apple’s iPads — is that Android tablets are available for so much cheaper than iPads. Google’s latest Nexus 7 (2013) is available for only $230. Apple’s non-retina iPad Mini is available at $300, which is already $70 more. In spite of that, the iPad Mini has much older, slower internals and a much lower resolution screen. It’s not as nice to look at when it comes to reading or watching movies, and the iPad Mini reportedly struggles to run Apple’s latest iOS 7. In contrast, the new Nexus 7 has a very high resolution screen, speedy internals, and runs Android very well with little-to-no lag in real use. We haven’t had any problems with it, unlike all the problems we unfortunately encountered with the first Nexus 7. For a really comparable experience to the current Nexus 7, you’d want to get one of Apple’s new retina iPad Minis. That would cost you $400, another $170 over the Nexus 7. In fact, it’s possible to regularly find sales on the Nexus 7, so if you waited you could get it for just $200 — half the price of the iPad mini with a comparable screen and internals. (In fairness, the iPad certainly has better hardware — but you won’t feel if it you’re just using your tablet to browse the web, watch videos, and do other typical tablet things.) This makes a tablet like the popular Nexus 7 a very good option for budget-conscious users who just want a high-quality device they can use to browse the web, watch videos, play games, and generally do light computing. There’s a reason we’re focusing on the Nexus 7 here. The combination of price and size brings it to a very good place. It’s awfully cheap for the high-quality experience you get, and the 7-inch screen means that even the non-tablet-optimized apps you may stumble across will often work fairly well. On the other hand, more expensive 10-inch Android tablets are still a tougher sell. For $400-$500, you’re getting awfully close to Apple’s full-size iPad price range and Android tablets don’t have as good an app ecosystem as an iPad. It’s hard to recommend an expensive, 10-inch Android tablet over a full-size iPad to average users. In summary, the Android app tablet app situation is nowhere near as bad as it was a few years ago. The success of the Nexus 7 proves that Android tablets can be compelling experiences, and there are a wide variety of strong apps. That said, more expensive 10-inch Android tablets that compete directly with the full-size iPad on price still don’t make much sense for most people.  Unless you have a specific reason for preferring an Android tablet, it’s tough not to recommend an iPad if you’re looking at spending $400+ on a 10-inch tablet. Image Credit: Christian Ghanime on Flickr, Christian Ghanime on Flickr     

  Read the article

• Organizing Connections with Folders in Oracle SQL Developer

  - by thatjeffsmith

  How many Oracle databases do you work with on a regular basis? I’m guessing the answer for most of you lies between 1 and 500. This post is really geared for those of you who deal with more than just a handful (5) of database connections. Filters are nice when you need to work with a subset of table data, or even a list of tables. So why wouldn’t they be just as useful for organizing your connections? Here’s my complete list of databases: The folders aren’t there by default, you add them as you need them. Now this isn’t an overly large connection list. But when I need to fire up an impromptu demo for a customer, it’s very nice to be able to drill down into JUST those ‘safe’ environments. This actually saves me a few seconds every time I need to connect to one of my databases. So while it’s a very simple feature, it’s one of those things that I recommend EVERYONE take advantage of as it will save them hours of time over the long haul. Easier to find means I get to work a few seconds faster. This also helps me from making mistakes in ‘production’ environments! How to Add a Connection Folder Select a connection you want to organize. Mouse-right-click, and choose ‘Add to folder.’ You can throw it into a new container or an existing one. Lather, rinse, and repeat as necessary. The only trick is remembering to right-click! Special thanks to @dresendi for today’s topic! He asked how to do this and I realized I hadn’t blogged the topic yet

  Read the article

• Colour coding of the status bar in SQL Server Management Studio - Oh dear

  - by simonsabin

  The new feature in SQL Server 2008 to have your query window status bar colour coded to the server you are on is great. Its a nice way to distinguish production from development servers. Unfortunately it was pointed out to me by a client recently that it doesn't always work. To me that sort of makes it pointless. Its a bit like having breaks that work some of the time. Are you going to place Russian roulette every time you execute the query. Whats more the colour doesn't change if you change the connection. So you can flip between dev and production servers but your status bar stays the colour you set for the dev server. It really annoys me to find features that sort of work. The reason I initially gave up on SQLPrompt was that it didn't work 100% of the time and for that time it didn't work I wasted so much time trying to get it to work I wasted more time than if I didn't have it. (I will say that was 2-3 years ago). If you would like to use this feature but aren't because of these features please vote on these bugs. https://connect.microsoft.com/SQLServer/feedback/details/504418/ssms-make-color-coding-of-query-windows-work-all-the-time https://connect.microsoft.com/SQLServer/feedback/details/361832/update-status-bar-colour-when-changing-connections  

  Read the article

• Ask the Readers: How Do You Deal with Bacn?

  - by Jason Fitzpatrick

  Most people get their fair share of email they want, email they don’t want at all (Spam), and a healthy dose of Bacn–email they want but not right now. How do you deal with your daily dose of Bacn? While Spam is unsolicited garbage you don’t ever want, Bacn is email content you’ve actively selected to receive (weather updates, coupons from your favorite retailers, web site digests, etc.) that isn’t as important as email from friends and coworkers. It’s email that you want but not right now. This week we want to hear all about your methods for wrangling Bacn so you can enjoy it when you’re in the mood but it doesn’t clutter up your inbox when you aren’t. Sound off in the comments with your Bacn handling tips and then check back in on Friday for the What You Said roundup to see how your fellow readers handle things. HTG Explains: What The Windows Event Viewer Is and How You Can Use It HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows?

  Read the article

• SQL SERVER – Grouping by Multiple Columns to Single Column as A String

  - by pinaldave

  One of the most common questions I receive in email is how to group multiple column data in comma separate values in a single row grouping by another column. I have previously blogged about it in following two blog posts. However, both aren’t addressing the following exact problem. Comma Separated Values (CSV) from Table Column Comma Separated Values (CSV) from Table Column – Part 2 The question comes in many different formats but in following image I am demonstrating the same question in simple words. This is the most popular question on my Facebook page as well. (Example) Here is the sample script to build the sample dataset. CREATE TABLE TestTable (ID INT, Col VARCHAR(4)) GO INSERT INTO TestTable (ID, Col) SELECT 1, 'A' UNION ALL SELECT 1, 'B' UNION ALL SELECT 1, 'C' UNION ALL SELECT 2, 'A' UNION ALL SELECT 2, 'B' UNION ALL SELECT 2, 'C' UNION ALL SELECT 2, 'D' UNION ALL SELECT 2, 'E' GO SELECT * FROM TestTable GO Here is the solution which will build an answer to the above question. -- Get CSV values SELECT t.ID, STUFF( (SELECT ',' + s.Col FROM TestTable s WHERE s.ID = t.ID FOR XML PATH('')),1,1,'') AS CSV FROM TestTable AS t GROUP BY t.ID GO I hope this is an easy solution. I am going to point to this blog post in the future for all the similar questions. Final Clean Up Act -- Clean up DROP TABLE TestTable GO Here is the question back to you - Is there any better way to write above script? Please leave a comment and I will write a separate blog post with due credit. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: SQL XML

  Read the article

• From Bluehost to WP Engine, My WordPress Story

  - by thatjeffsmith

  This is probably the longest blog post I’ve written in a LONG time. And if you’re used to coming here for the Oracle stuff, this post is not about that. It’s about my blog, and the stuff under the hood that makes it run, AKA WordPress. If you want to skip to the juicy stuff, then use these shortcuts: My Site Slowed Down How I Moved to WP Engine How WP Engine ‘Hooked’ Me Why WP Engine? I started thatJeffSmith.com on May 28th, 2010. I had been already been blogging for several years, but a couple of really smart people I respected (Andy, Brent – thanks again!) suggested that I take ownership of my content and begin building my personal brand. I thought that was a good idea, and so I signed up for service with bluehost. Bluehost makes setting up a WordPress site very, very easy. And, they continued to be easy to work with for the past 2 years. I would even recommend them to anyone looking to host their own WordPress install/site. For $83.40, I purchased a year’s worth of service and my domain name registration – a very good value. And then last year I paid $107.40 for another year’s services. And when that year expired I paid another $190.80 for an additional two year’s service in advance. I had been up to that point, getting my money’s worth. And then, just a few weeks ago… My Site Slowed to a Crawl That spike was from an April Fool's Day Post, I think Why? Well, when I first started blogging, I had the same problem that most beginner bloggers have – not many readers. In my first year of blogging, I think the highest number of readers on a single day was about 125. I remember that day as I was very excited to break 100! Bluehost was very reliable, serving up my content with maybe a total of 3-4 outages in the past 2 years. Support was usually very prompt with answers and solutions, and I love their ‘Chat now’ technology – much nicer than message boards only or pay-to-talk phone support. In the past 6 months however, I noticed a couple of things: daily traffic was increasing – woohoo! my service was experiencing severe CPU throttling – doh! To be honest, I wasn’t aware the throttling was occuring, but I did know that the response time of my blog was starting to lag. Average load times were approaching 20-30 seconds. Not good when good sites are loading in 5 seconds or less. And just this past week, in getting ready to launch a new website for work that sucked in an RSS feed from my blog, the new page was left waiting for more than a minute. Not good! In fact my boss asked, why aren’t you blogging on Blogger? Ugh. I tried a few things to fix the problem: I paid for a premium WordPress theme – Themify’s Grido (thanks to @SQLRockstar for the heads-up) I installed a couple of WP caching plugins I read every WP optimization blog post I could get my greedy little eyes on However, at the same time I was also getting addicted to WordPress bloggers talking about all the cool things you could do with your blog. As a result I had at one point about 30 different plugins installed. WordPress runs on MySQL, and certain queries running via these plugins were starving for CPU. Plugins that would be called every page load meant that as more people clicked on my site, the more CPU I needed. I’m not stupid, so I eventually figured out that maybe less plugins was better, and was able to go down to just 20. But still, the site was running like a dog. CPU Throttling, makes MySQL wait to run a query Bluehost runs shared servers. Your site runs on the same box that several hundred (or thousand?) other services are running on. If you take more CPU than they think you should have, they will limit your service by making you stand in line for CPU, AKA ‘throttling.’ This is not bad. This business model allows them to serve many, many users for a very fair price. It works great until, well, until it doesn’t. I noticed in the last week that for every minute of service, I was being throttled between 60 and 300 seconds. If there were 5 MySQL processes running, then every single one of them were being held in check. The blog visitor notice this as their page requests would take a minute or more to be answered. Bluehost unfortunately doesn’t offer dedicated server hosting, so there was no real upgrade path for me follow and remain one of their customers. So what was I to do? Uninstall every plugin and hope the site sped up? Ask for people to take turns on my blog? I decided to spend my way out of the problem. I signed up for service with WP Engine and moved ThatJeffSmith.com The first 2 months are free, and after that it’s about $29/month to run my site on their system. My math tells me that’s a good bit more expensive than what Bluehost was charging me – to the tune of about 300% more a month. Oh, and I should just say that my blog is a personal blog even though I talk about work stuff here. I don’t get paid for blogging, I don’t sell ads, and I don’t expense the service fees – this is my personal passion. So is it worth it? In the first 4 days, it seems to be totally worth it. Load times have gone from 20-30 seconds to less than 5 seconds. A few folks have told me via Twitter that they notice faster page loads. I anticipate this will indirectly lead to more traffic as Google penalizes you in search results if your site is too slow, and of course some folks won’t even bother waiting more than 5-10 seconds. I noticed right away that writing posts, uploading pictures, and just using the WordPress dashboard in general was much more responsive. So writing is less of a chore now, which means I won’t have a good reason not to write How I Moved to WP Engine I signed up for the service and registered my domain. I then took a full export of my ‘old’ site by doing a FTP GET of all my files, then did a MySQL database backup, exported my WordPress Theme settings to a .zip file, and then finally used the WordPress ‘Export’ feature. I then used the WordPress ‘Import’ on the new site to load up my posts. Then I uploaded the theme .zip package from Themify. Then I FTP’d the ‘wp-content’ directory up to my new server using SFTP (WP Engine only supports secure FTP – good on them!) Using a temporary URL to see my new site, I was able to confirm that everything looked mostly OK – I’ll detail the challenges and issues of fixing the content next – but then it was time to ‘flip the switch.’ I updated the IP address that the DNS lookup tables use to route traffic to my new server. In a matter of minutes the DNS servers around the world were updated and it was time to see the new site! But It Was ‘Broken’ I had never moved a website before, and in my rush to update the DNS, I had changed the records without really finding out what I was supposed to do first. After re-reading the directions provided by WP Engine and following the guidance of their support engineer, I realized I had needed to set the CNAME (Alias) ‘www’ record to point to a different URL than the ‘www.thatjeffsmith.com’ entry I had set. Once corrected the site was up and running in less than a minute. Then It Was Only Mostly Broken Many of my plugins weren’t working. Apparently just ftp’ing the wp-content directory up wasn’t the proper way to re-install the plugin. I suspect file permissions or file ownership wasn’t proper. Some plug-ins were working, many had their settings wiped to the defaults, and a few just didn’t work again. I had to delete the directory of the plug-in manually via SFTP, and then use the WP Dashboard to install it from scratch. And here was my first ‘lesson’ – don’t switch the DNS records until you’ve completely tested your new site. I wasn’t able to navigate the old WP console to review my plug-in settings. Thankfully I was able to use the Wayback Machine to reverse engineer some things, and of course most plug-ins aren’t that complicated to setup to begin with. An example of one that I had to redo from scratch is the ‘Twitter @Anywhere Plus’ plugin that I use to create the form that allows folks to tweet a post they enjoyed at the end of each story. How WP Engine ‘Hooked’ Me I actually signed up with another provider first. They ranked highly in Google searches and a few Tweeps recommended them to me. But hours after signing up and I still didn’t have sever reyady, I was ready to give up on them. They offered no chat or phone support – only mail and message boards. And the message boards were rife with posts about how the service had gone downhill in the past 6 months. To their credit, they did make it easy to cancel, although I did have to do so via email as their website ‘cancel’ button was non-existent. Within minutes of activating my WP Engine account I had received my welcome message and directions on how to get started. I was able to see my staged website right away. They also did something very cool before I even got started – they looked at my existing site and told me by how much they could improve its performance. The proof is in the web pudding. I like this for a few reasons, but primarily I liked their business model. It told me they knew what they were doing, and that they were willing to put their money where their mouth was. This was further evident by their 60-day money back guarantee. And if I understand it correctly, they don’t even take your money until after that 60 day period is over. After a day, I was welcomed by the WP Engine social media team, and was given the opportunity to subscribe to their newsletter and follow their account on Twitter. I noticed their Twitter team is sure to post regular WordPress tips several times a day. It’s not just an account that’s setup for the sake of having a Twitter presence. These little things add up and give me confidence in my decision to choose them as my hosting partner. ‘Partner’ – that’s a lot nicer word than just ‘service provider,’ isn’t it? Oh, and they offered me a t-shirt. Don’t ever doubt the power of a ‘free’ t-shirt! How awesome is this e-mail, from a customer perspective? I wasn’t really expecting any of this. Exceeding expectations before I have even handed over a single dollar seems like a pretty good business plan. This is how you treat customers. Love them to death, and they reward you with loyalty. But Jeff, You Skipped a Piece Here, Why WP Engine? I found them on one of those ‘Top 10′ list posts, and pulled up their webpage. I noticed they offered a specialized service – they host WordPress installs, and that’s it. Their servers are tuned specifically for running WordPress. They had in bolded text, things like ‘INSANELY FAST. INFINITELY SCALABLE.’ and ‘LIGHTNING SPEED.’ And then they offered insurance against hackers and they took care of automatic backups and restores. The only drawbacks I have noticed so far relate to plugins I used that have been ‘blacklisted.’ In order to guarantee that ‘lightning’ speed, they have banned the use of the CPU-suckiest plugins. One of those is the ‘Related Posts’ plugin. So if you are a subscriber and are reading this in your email, you’ll notice there’s no links back to my blog to continue reading other related stories. Since that referral traffic is very small single-digit for my site, I decided that I’m OK with that. I’d rather have the warp-speed page loads. Again, I think that will lead to higher traffic down the road. In 50+ days I will need to decide if WP Engine is a permanent solution. I’ll be sure to update this post when that time comes and let y’all know how it turns out.

  Read the article

• How to Run Low-Cost Minecraft on a Raspberry Pi for Block Building on the Cheap

  - by Jason Fitzpatrick

  We’ve shown you how to run your own blocktastic personal Minecraft server on a Windows/OSX box, but what if you crave something lighter weight, more energy efficient, and always ready for your friends? Read on as we turn a tiny Raspberry Pi machine into a low-cost Minecraft server you can leave on 24/7 for around a penny a day. Why Do I Want to Do This? There’s two aspects to this tutorial, running your own Minecraft server and specifically running that Minecraft server on a Raspberry Pi. Why would you want to run your own Minecraft server? It’s a really great way to extend and build upon the Minecraft play experience. You can leave the server running when you’re not playing so friends and family can join and continue building your world. You can mess around with game variables and introduce mods in a way that isn’t possible when you’re playing the stand-alone game. It also gives you the kind of control over your multiplayer experience that using public servers doesn’t, without incurring the cost of hosting a private server on a remote host. While running a Minecraft server on its own is appealing enough to a dedicated Minecraft fan, running it on the Raspberry Pi is even more appealing. The tiny little Pi uses so little resources that you can leave your Minecraft server running 24/7 for a couple bucks a year. Aside from the initial cost outlay of the Pi, an SD card, and a little bit of time setting it up, you’ll have an always-on Minecraft server at a monthly cost of around one gumball. What Do I Need? For this tutorial you’ll need a mix of hardware and software tools; aside from the actual Raspberry Pi and SD card, everything is free. 1 Raspberry Pi (preferably a 512MB model) 1 4GB+ SD card This tutorial assumes that you have already familiarized yourself with the Raspberry Pi and have installed a copy of the Debian-derivative Raspbian on the device. If you have not got your Pi up and running yet, don’t worry! Check out our guide, The HTG Guide to Getting Started with Raspberry Pi, to get up to speed. Optimizing Raspbian for the Minecraft Server Unlike other builds we’ve shared where you can layer multiple projects over one another (e.g. the Pi is more than powerful enough to serve as a weather/email indicator and a Google Cloud Print server at the same time) running a Minecraft server is a pretty intense operation for the little Pi and we’d strongly recommend dedicating the entire Pi to the process. Minecraft seems like a simple game, with all its blocky-ness and what not, but it’s actually a pretty complex game beneath the simple skin and required a lot of processing power. As such, we’re going to tweak the configuration file and other settings to optimize Rasbian for the job. The first thing you’ll need to do is dig into the Raspi-Config application to make a few minor changes. If you’re installing Raspbian fresh, wait for the last step (which is the Raspi-Config), if you already installed it, head to the terminal and type in “sudo raspi-config” to launch it again. One of the first and most important things we need to attend to is cranking up the overclock setting. We need all the power we can get to make our Minecraft experience enjoyable. In Raspi-Config, select option number 7 “Overclock”. Be prepared for some stern warnings about overclocking, but rest easy knowing that overclocking is directly supported by the Raspberry Pi foundation and has been included in the configuration options since late 2012. Once you’re in the actual selection screen, select “Turbo 1000MhHz”. Again, you’ll be warned that the degree of overclocking you’ve selected carries risks (specifically, potential corruption of the SD card, but no risk of actual hardware damage). Click OK and wait for the device to reset. Next, make sure you’re set to boot to the command prompt, not the desktop. Select number 3 “Enable Boot to Desktop/Scratch”  and make sure “Console Text console” is selected. Back at the Raspi-Config menu, select number 8 “Advanced Options’. There are two critical changes we need to make in here and one option change. First, the critical changes. Select A3 “Memory Split”: Change the amount of memory available to the GPU to 16MB (down from the default 64MB). Our Minecraft server is going to ruin in a GUI-less environment; there’s no reason to allocate any more than the bare minimum to the GPU. After selecting the GPU memory, you’ll be returned to the main menu. Select “Advanced Options” again and then select A4 “SSH”. Within the sub-menu, enable SSH. There is very little reason to keep this Pi connected to a monitor and keyboard, by enabling SSH we can remotely access the machine from anywhere on the network. Finally (and optionally) return again to the “Advanced Options” menu and select A2 “Hostname”. Here you can change your hostname from “raspberrypi” to a more fitting Minecraft name. We opted for the highly creative hostname “minecraft”, but feel free to spice it up a bit with whatever you feel like: creepertown, minecraft4life, or miner-box are all great minecraft server names. That’s it for the Raspbian configuration tab down to the bottom of the main screen and select “Finish” to reboot. After rebooting you can now SSH into your terminal, or continue working from the keyboard hooked up to your Pi (we strongly recommend switching over to SSH as it allows you to easily cut and paste the commands). If you’ve never used SSH before, check out how to use PuTTY with your Pi here. Installing Java on the Pi The Minecraft server runs on Java, so the first thing we need to do on our freshly configured Pi is install it. Log into your Pi via SSH and then, at the command prompt, enter the following command to make a directory for the installation: sudo mkdir /java/ Now we need to download the newest version of Java. At the time of this publication the newest release is the OCT 2013 update and the link/filename we use will reflect that. Please check for a more current version of the Linux ARMv6/7 Java release on the Java download page and update the link/filename accordingly when following our instructions. At the command prompt, enter the following command: sudo wget --no-check-certificate http://www.java.net/download/jdk8/archive/b111/binaries/jdk-8-ea-b111-linux-arm-vfp-hflt-09_oct_2013.tar.gz Once the download has finished successfully, enter the following command: sudo tar zxvf jdk-8-ea-b111-linux-arm-vfp-hflt-09_oct_2013.tar.gz -C /opt/ Fun fact: the /opt/ directory name scheme is a remnant of early Unix design wherein the /opt/ directory was for “optional” software installed after the main operating system; it was the /Program Files/ of the Unix world. After the file has finished extracting, enter: sudo /opt/jdk1.8.0/bin/java -version This command will return the version number of your new Java installation like so: java version "1.8.0-ea" Java(TM) SE Runtime Environment (build 1.8.0-ea-b111) Java HotSpot(TM) Client VM (build 25.0-b53, mixed mode) If you don’t see the above printout (or a variation thereof if you’re using a newer version of Java), try to extract the archive again. If you do see the readout, enter the following command to tidy up after yourself: sudo rm jdk-8-ea-b111-linux-arm-vfp-hflt-09_oct_2013.tar.gz At this point Java is installed and we’re ready to move onto installing our Minecraft server! Installing and Configuring the Minecraft Server Now that we have a foundation for our Minecraft server, it’s time to install the part that matter. We’ll be using SpigotMC a lightweight and stable Minecraft server build that works wonderfully on the Pi. First, grab a copy of the the code with the following command: sudo wget http://ci.md-5.net/job/Spigot/lastSuccessfulBuild/artifact/Spigot-Server/target/spigot.jar This link should remain stable over time, as it points directly to the most current stable release of Spigot, but if you have any issues you can always reference the SpigotMC download page here. After the download finishes successfully, enter the following command: sudo /opt/jdk1.8.0/bin/java -Xms256M -Xmx496M -jar /home/pi/spigot.jar nogui Note: if you’re running the command on a 256MB Pi change the 256 and 496 in the above command to 128 and 256, respectively. Your server will launch and a flurry of on-screen activity will follow. Be prepared to wait around 3-6 minutes or so for the process of setting up the server and generating the map to finish. Future startups will take much less time, around 20-30 seconds. Note: If at any point during the configuration or play process things get really weird (e.g. your new Minecraft server freaks out and starts spawning you in the Nether and killing you instantly), use the “stop” command at the command prompt to gracefully shutdown the server and let you restart and troubleshoot it. After the process has finished, head over to the computer you normally play Minecraft on, fire it up, and click on Multiplayer. You should see your server: If your world doesn’t popup immediately during the network scan, hit the Add button and manually enter the address of your Pi. Once you connect to the server, you’ll see the status change in the server status window: According to the server, we’re in game. According to the actual Minecraft app, we’re also in game but it’s the middle of the night in survival mode: Boo! Spawning in the dead of night, weaponless and without shelter is no way to start things. No worries though, we need to do some more configuration; no time to sit around and get shot at by skeletons. Besides, if you try and play it without some configuration tweaks first, you’ll likely find it quite unstable. We’re just here to confirm the server is up, running, and accepting incoming connections. Once we’ve confirmed the server is running and connectable (albeit not very playable yet), it’s time to shut down the server. Via the server console, enter the command “stop” to shut everything down. When you’re returned to the command prompt, enter the following command: sudo nano server.properties When the configuration file opens up, make the following changes (or just cut and paste our config file minus the first two lines with the name and date stamp): #Minecraft server properties #Thu Oct 17 22:53:51 UTC 2013 generator-settings= #Default is true, toggle to false allow-nether=false level-name=world enable-query=false allow-flight=false server-port=25565 level-type=DEFAULT enable-rcon=false force-gamemode=false level-seed= server-ip= max-build-height=256 spawn-npcs=true white-list=false spawn-animals=true texture-pack= snooper-enabled=true hardcore=false online-mode=true pvp=true difficulty=1 player-idle-timeout=0 gamemode=0 #Default 20; you only need to lower this if you're running #a public server and worried about loads. max-players=20 spawn-monsters=true #Default is 10, 3-5 ideal for Pi view-distance=5 generate-structures=true spawn-protection=16 motd=A Minecraft Server In the server status window, seen through your SSH connection to the pi, enter the following command to give yourself operator status on your Minecraft server (so that you can use more powerful commands in game, without always returning to the server status window). op [your minecraft nickname] At this point things are looking better but we still have a little tweaking to do before the server is really enjoyable. To that end, let’s install some plugins. The first plugin, and the one you should install above all others, is NoSpawnChunks. To install the plugin, first visit the NoSpawnChunks webpage and grab the download link for the most current version. As of this writing the current release is v0.3. Back at the command prompt (the command prompt of your Pi, not the server console–if your server is still active shut it down) enter the following commands: cd /home/pi/plugins sudo wget http://dev.bukkit.org/media/files/586/974/NoSpawnChunks.jar Next, visit the ClearLag plugin page, and grab the latest link (as of this tutorial, it’s v2.6.0). Enter the following at the command prompt: sudo wget http://dev.bukkit.org/media/files/743/213/Clearlag.jar Because the files aren’t compressed in a .ZIP or similar container, that’s all there is to it: the plugins are parked in the plugin directory. (Remember this for future plugin downloads, the file needs to be whateverplugin.jar, so if it’s compressed you need to uncompress it in the plugin directory.) Resart the server: sudo /opt/jdk1.8.0/bin/java -Xms256M -Xmx496M -jar /home/pi/spigot.jar nogui Be prepared for a slightly longer startup time (closer to the 3-6 minutes and much longer than the 30 seconds you just experienced) as the plugins affect the world map and need a minute to massage everything. After the spawn process finishes, type the following at the server console: plugins This lists all the plugins currently active on the server. You should see something like this: If the plugins aren’t loaded, you may need to stop and restart the server. After confirming your plugins are loaded, go ahead and join the game. You should notice significantly snappier play. In addition, you’ll get occasional messages from the plugins indicating they are active, as seen below: At this point Java is installed, the server is installed, and we’ve tweaked our settings for for the Pi.  It’s time to start building with friends!     

  Read the article

• VS2010 Publish Profiles -- Where are they stored?

  - by Jeff S

  We have set up a few Publish Profiles that are used to deploy web apps to various servers, and it all works great with 1-click deployment. However, w find that even though the entire solution is under source control (svn), the profiles do not seem to be carried over, so we need to re-create the profiles on each developer's machine manually. It seems, since the profiles only exist for the solution currently loaded, that they must be stored in the solution files somewhere, but they do not carry over when someone else does an update to pull down the code. I'm guessing whatever file they're in is one we aren' covering in the source control project, but I haven't been able to figure out which one. Someone must know where the Publish Profiles are stored -- is there any way to copy them from machine to machine so we don't have to retype them for each developer?

  Read the article

• How To Disconnect Non-Mapped UNC Path “Drives” in Windows

  - by The Geek

  Have you ever browsed over to another PC on your network using “network neighborhood”, and then connected to one of the file shares? Without a drive letter, how do you disconnect yourself once you’ve done so? Really confused as to what I’m talking about? Let’s walk through the process. First, imagine that you browse through and connect to a share, entering your username and password to gain access. The problem is that you stay connected, and there’s no visible way to disconnect yourself. If you try and shut down the other PC, you’ll receive a message that users are still connected. So let’s disconnect! Open up a command prompt, and then type in the following: net use This will give you a list of the connected drives, including the ones that aren’t actually mapped to a drive letter. To disconnect one of the connections, you can use the following command: net use /delete \\server\sharename For example, in this instance we’d disconnect like so: net use /delete \\192.168.1.205\root$ Now when you run the “net use” command again, you’ll see that you’ve been properly disconnected. If you wanted to actually connect to a share without mapping a drive letter, you can do the following: net use /user:Username \\server\sharename Password You could then just pop \\server\sharename into a Windows Explorer window and browse the files that way. Note that this technique should work exactly the same in any version of windows. Similar Articles Productive Geek Tips Remove "Map Network Drive" Menu Item from Windows Vista or XPDisable the Annoying "This page has an unspecified potential security risk" When Using Files on a Network ShareCopy Path of a File to the Clipboard in Windows 7 or VistaMap a Network Drive from XP to Windows 7Defrag Multiple Hard Drives At Once In Windows TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily

  Read the article

• Add "My Dropbox" to Your Windows 7 Start Menu

  - by The Geek

  Over here at How-To Geek, we’re huge fans of Dropbox, the amazingly fast online file sync utility, but we’d be even happier if we could natively add it to the Windows 7 Start Menu, where it belongs. And today, that’s what we’ll do. Yep, that’s right. You can add it to the Start Menu… using a silly hack to the Libraries feature and renaming the Recorded TV library to a different name. It’s not a perfect solution, but you can access your Dropbox folder this way and it just seems to belong there. First things first, head into the Customize Start Menu panel by right-clicking on the start menu and using Properties, then make sure that Recorded TV is set to “Display as a link”. Next, right-click on Recorded TV, choose Rename, and then change it to something else like My Dropbox.   Now you’ll want to right-click on that button again, and choose Properties, where you’ll see the Library locations in the list… the general idea is that you want to remove Recorded TV, and then add your Dropbox folder. Oh, and you’ll probably want to make sure to set “Optimize this library for” to “General Items”. At this point, you can just click on My Dropbox, and you’ll see, well, Your Dropbox! (no surprise there). Yeah, I know, it’s totally a hack. But it’s a very useful one! Also, if you aren’t already using Dropbox, you should really check it out—2 GB for free, accessible via the web from anywhere, and you can sync to multiple desktops. Similar Articles Productive Geek Tips Use the Windows Key for the "Start" Menu in Ubuntu LinuxAccess Your Dropbox Files in Google ChromeSpeed up Windows Vista Start Menu Search By Limiting ResultsPin Any Folder to the Vista Start Menu the Easy WayEnable "Pin to Start Menu" for Folders in Windows Vista / XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Classic Cinema Online offers 100’s of OnDemand Movies OutSync will Sync Photos of your Friends on Facebook and Outlook Windows 7 Easter Theme YoWindoW, a real time weather screensaver Optimize your computer the Microsoft way Stormpulse provides slick, real time weather data

  Read the article

• Step Away From That Computer! You’re Not Qualified to Use It!

  - by Michael Sorens

  Most things tend to come with warnings and careful instructions these days, but sadly not one of the most ubiquitous appliances of all, your computer. If a chainsaw is missing its instructions, you’re well advised not to use it, even though you probably know roughly how it’s supposed to work. I confess, there are days when I feel the same way about computers. Long ago, during the renaissance of the computer age, it was possible to know everything about computers. But today, it is challenging to be fully knowledgeable even in one small area, and most people aren’t as savvy as they like to think. And, if I may borrow from Edwin Abbott Abbott’s classic Flatland, that includes me. And you. Need an example of what I mean? Take a look at almost any recent month’s batch of Windows updates. Just two quick questions for you: Do you need all of those updates? Is it safe to install all of those updates? I do software design and development for a living on Windows and the .NET platform, but I will be quite candid: I often have little clue what the heck some of those updates are going to do or why they are needed. So, if you do not know why they are needed or what they do, how do you know if they are safe? Of course, one can sidestep both questions by accepting Microsoft’s recommended Windows Update setting of “install updates automatically”. That leads you to infer that you need all of them (which is not always the case) and, more significantly, that they are safe. Quite safe. Ah, lest reality intrude upon such a pretty picture! Sadly, there is no such thing as risk-free software installation, and payloads from Windows Update are no exception. Earlier this year, a Windows Secrets Patch Watch article touted this headline: Keep this troublesome kernel update on hold. It discusses KB 2862330, a security update originally published more than 4 months earlier, and yet the article still recommends not installing it! Most people simply do not have the time, resources, or interest, to go about figuring out which updates to install or postpone or skip for safety reasons. Windows Secrets Patch Watch is the best service I have encountered for getting advice, but it is still no panacea and using the service effectively requires a degree of computer literacy that I still think is beyond a good number of people. Which brings us full circle: Step Away From That Computer! You’re Not Qualified to Use It!

  Read the article

• Software Tuned to Humanity

  - by Phil Factor

  I learned a great deal from a cynical old programmer who once told me that the ideal length of time for a compiler to do its work was the same time it took to roll a cigarette. For development work, this is oh so true. After intently looking at the editing window for an hour or so, it was a relief to look up, stretch, focus the eyes on something else, and roll the possibly-metaphorical cigarette. This was software tuned to humanity. Likewise, a user’s perception of the “ideal” time that an application will take to move from frame to frame, to retrieve information, or to process their input has remained remarkably static for about thirty years, at around 200 ms. Anything else appears, and always has, to be either fast or slow. This could explain why commercial applications, unlike games, simulations and communications, aren’t noticeably faster now than they were when I started programming in the Seventies. Sure, they do a great deal more, but the SLAs that I negotiated in the 1980s for application performance are very similar to what they are nowadays. To prove to myself that this wasn’t just some rose-tinted misperception on my part, I cranked up a Z80-based Jonos CP/M machine (1985) in the roof-space. Within 20 seconds from cold, it had loaded Wordstar and I was ready to write. OK, I got it wrong: some things were faster 30 years ago. Sure, I’d now have had all sorts of animations, wizzy graphics, and other comforting features, but it seems a pity that we have used all that extra CPU and memory to increase the scope of what we develop, and the graphical prettiness, but not to speed the processes needed to complete a business procedure. Never mind the weight, the response time’s great! To achieve 200 ms response times on a Z80, or similar, performance considerations influenced everything one did as a developer. If it meant writing an entire application in assembly code, applying every smart algorithm, and shortcut imaginable to get the application to perform to spec, then so be it. As a result, I’m a dyed-in-the-wool performance freak and find it difficult to change my habits. Conversely, many developers now seem to feel quite differently. While all will acknowledge that performance is important, it’s no longer the virtue is once was, and other factors such as user-experience now take precedence. Am I wrong? If not, then perhaps we need a new school of development technique to rival Agile, dedicated once again to producing applications that smoke the rear wheels rather than pootle elegantly to the shops; that forgo skeuomorphism, cute animation, or architectural elegance in favor of the smell of hot rubber. I struggle to name an application I use that is truly notable for its blistering performance, and would dearly love one to do my everyday work – just as long as it doesn’t go faster than my brain.

  Read the article

• What Is .recently-used.xbel and How Do I Delete It for Good?

  - by The Geek

  If you’re reading this article, you’ve probably noticed the .recently-used.xbel file in the root of your User folder, and you’re wondering why it keeps constantly coming back even though you repeatedly delete it. So What Is It? The quick answer is that it’s part of the GTK+ library used by a number of cross-platform applications, perhaps the most well-known of which is the Pidgin instant messenger client. As the name implies, the file is used to store a list of the most recently used files. In the case of Pidgin, this comes into play when you are transferring files over IM, and that’s when the file will appear again. Note: this is actually a known and reported bug in Pidgin, but sadly the developers aren’t terribly responsive when it comes to annoyances. Pidgin seems to go for long periods of time without any updates, but we still use it because it’s open-source, cross-platform, and works well. How Do I Get Rid of It? Unfortunately, there’s no way to easily get rid of it, apart from using a different application. If you need to transfer files over Pidgin, the file is going to re-appear… but there’s a quick workaround! The general idea is to set the file properties to Hidden and Read-only. You’d think you could just set it to Hidden and be done with it, but Pidgin will re-create the file every time, so instead we’re leaving the file there and preventing it from being accessed. You could also totally remove access through the Security tab if you wanted to, but this worked fine for me… as you can see, no more file in the folder. Of course, you can’t have the show hidden files and folders option turned on, or the file will continue to show up. Want to get really geeky? You can toggle hidden files with a shortcut key. Similar Articles Productive Geek Tips Hide Recently Used Documents/Programs From the Windows Vista Start MenuQuick Tip: Windows Vista Temp Files DirectoryDelete Wrong AutoComplete Entries in Windows Vista MailDisable Delete Confirmation Dialog in Windows 7 or VistaHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily

  Read the article

• The Problem Should Define the Process, Not the Tool

  - by thatjeffsmith

  All around awesome tool, but not the only gadget in your toolbox.I’m stepping down from my SQL Developer pulpit today and standing up on my philosophical soap box. I’m frequently asked to help folks transition from one set of database tools over to Oracle SQL Developer, which I’m MORE than happy to do. But, I’m not looking to simply change the way people interact with Oracle database. What I care about is your productivity. Is there a faster, more efficient way for you to connect the dots, get from A to B, or just get home to your kids or to the pub for happy hour? If you have defined a business process around a specific tool, what happens when that tool ‘goes away?’ Does the business stop? No, you feel immediate pain until you are able to re-implement the process using another mechanism. Where I get confused, or even frustrated, is when someone asks me to redesign our tool to match their problem. Tools are just tools. Saying you ‘can’t load your data anymore because XYZ’ isn’t valid when you could easily do that same task via SQL*Loader, Create Table As Selects, or 9 other different mechanisms. Sometimes changes brings opportunity for improvement in the process. Don’t be afraid to step back and re-evaluate a problem with a fresh set of eyes. Just trying to replicate your process in another tool exactly as it was done in the ‘old tool’ doesn’t always make sense. Quick sidebar: scheduling a Windows program to kick off thousands if not millions of table inserts from Excel versus using a ‘proper’ server process using SQL*Loader and or external tables means sacrificing scalability and reliability for convenience. Don’t let old habits blind you to new solutions and possibilities. Of couse I’m not going to sit here and say that our tools aren’t deficient in some areas or can’t be improved upon. But I bet if we work together we can find something that’s not only better for the business, but is also better for you. What do you ‘miss’ since you’ve started using SQL Developer as your primary Oracle database tools? I’d love to start a thread here and share ideas on how we can better serve you and your organizations needs. The end solution might not look exactly what you have in mind starting out, but I had no idea I’d be a Product Manager when I started college either What can you no longer ‘do’ since you picked up SQL Developer? What hurts more than it should? What keeps you from being great versus just good?

  Read the article

• Oracle SQL Developer Data Modeler: What Tables Aren’t In At Least One SubView?

  - by thatjeffsmith

  Organizing your data model makes the information easier to consume. One of the organizational tools provided by Oracle SQL Developer Data Modeler is the ‘SubView.’ In a nutshell, a SubView is a subset of your model. The Challenge: I’ve just created a model which represents my entire ____________ application. We’ll call it ‘residential lending.’ Instead of having all 100+ tables in a single model diagram, I want to break out the tables by module, e.g. appraisals, credit reports, work histories, customers, etc. I’ve spent several hours breaking out the tables to one or more SubViews, but I think i may have missed a few. Is there an easy way to see what tables aren’t in at least ONE subview? The Answer Yes, mostly. The mostly comes about from the way I’m going to accomplish this task. It involves querying the SQL Developer Data Modeler Reporting Schema. So if you don’t have the Reporting Schema setup, you’ll need to do so. Got it? Good, let’s proceed. Before you start querying your Reporting Schema, you might need a data model for the actual reporting schema…meta-meta data! You could reverse engineer the data modeler reporting schema to a new data model, or you could just reference the PDFs in \datamodeler\reports\Reporting Schema diagrams directory. Here’s a hint, it’s THIS one The Query Well, it’s actually going to be at least 2 queries. We need to get a list of distinct designs stored in your repository. For giggles, I’m going to get a listing including each version of the model. So I can query based on design and version, or in this case, timestamp of when it was added to the repository. We’ll get that from the DMRS_DESIGNS table: SELECT DISTINCT design_name, design_ovid, date_published FROM DMRS_designs Then I’m going to feed the design_ovid, down to a subquery for my child report. select name, count(distinct diagram_id) from DMRS_DIAGRAM_ELEMENTS where design_ovid = :dESIGN_OVID and type = 'Table' group by name having count(distinct diagram_id) < 2 order by count(distinct diagram_id) desc Each diagram element has an entry in this table, so I need to filter on type=’Table.’ Each design has AT LEAST one diagram, the master diagram. So any relational table in this table, only having one listing means it’s not in any SubViews. If you have overloaded object names, which is VERY possible, you’ll want to do the report off of ‘OBJECT_ID’, but then you’ll need to correlate that to the NAME, as I doubt you’re so intimate with your designs that you recognize the GUIDs So I’m going to cheat and just stick with names, but I think you get the gist. My Model Of my almost 90 tables, how many of those have I not added to at least one SubView? Now let’s run my report! Voila! My ‘BEER2′ table isn’t in any SubView! It says ’1′ because the main model diagram counts as a view. So if the count came back as ’2′, that would mean the table was in the main model diagram and in 1 SubView diagram. And I know what you’re thinking, what kind of residential lending program would have a table called ‘BEER2?’ Let’s just say, that my business model has some kinks to work out!

  Read the article

• Google Chrome OS

  - by Piet

  It’s about time someone took this initiative: Google Chrome OS I especially like the following: Speed, simplicity and security are the key aspects of Google Chrome OS. We’re designing the OS to be fast and lightweight, to start up and get you onto the web in a few seconds. The user interface is minimal to stay out of your way, and most of the user experience takes place on the web. And as we did for the Google Chrome browser, we are going back to the basics and completely redesigning the underlying security architecture of the OS so that users don’t have to deal with viruses, malware and security updates. It should just work. I recently had the ‘pleasure’ witnessing several 60+ yr old friends and family (all respect for everyone in their 2nd or 3rd youth) buying their first pc, taking their first steps using a pc and the net. Have you ever seen the gazillions of little ‘useful’ tools that are installed on a new standard Vista pc or laptop ? This is like learning to drive a new car and being placed in an airplane cockpit. And all the messages one gets about virus/security checks, fingerprint nog being enrolled, trial period expiring (because half those really useful tools come with a trial period), … If I was in their shoes, being confronted with this as a total newbie, I guess I’d just give up pretty soon. As a matter of fact, I actually gave up on Vista on my work-laptop, it was driving me crazy. Thank god I was allowed to install XP. I’m a Linux user at home, and Vista was such a frustrating experience that Windows XP actually felt like breath of fresh air. And what are those people using? Email, browsing…. and maybe writing a little letter now and then or storing their photo’s if they have a digital camera. Actually (side note), I get the impression that hearing about facebook is a major motivator for the digital newbies to finally take the plunge, buy a pc and get on-line. And OK, we’ve seen initiatives like this before, but Google is a brand everyone knows… unlike Ubuntu, Debain or Mandriva. Google = God. If I was Microsoft I’d be wetting my pants knowing Google was about to release their own OS, without a doubt fully optimized to use their own on-line office suit. On the other hand, the old adage ‘no one ever got fired for choosing Microsoft’ still holds a lot of truth. I hope I’ll be able to give it a big thumbs up if a would-be pc-user asks me what kind of pc/OS they should go for in the near future. On the other hand, if I’d do that, I’m pretty sure a couple of weeks later I’d get a call asking how to install this game or photo editing tool they got from one of their Windows using friends… or that nifty photo-printer they just bought. But then, I also get those questions now from newbie Windows users. It takes a couple of years before Newbie pc users understand that some things just don’t work and aren’t worth the time trying to fix them. I’d just wish they’d go back to the shop when something doesn’t work. You also don’t let you mechanic friend try to fix a problem with your brand new car. But that’s another story… Wait and see…

  Read the article

• How Exactly Is One Linux OS “Based On” Another Linux OS?

  - by Jason Fitzpatrick

  When reviewing different flavors of Linux, you’ll frequently come across phrases like “Ubuntu is based on Debian” but what exactly does that mean? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader PLPiper is trying to get a handle on how Linux variants work: I’ve been looking through quite a number of Linux distros recently to get an idea of what’s around, and one phrase that keeps coming up is that “[this OS] is based on [another OS]“. For example: Fedora is based on Red Hat Ubuntu is based on Debian Linux Mint is based on Ubuntu For someone coming from a Mac environment I understand how “OS X is based on Darwin”, however when I look at Linux Distros, I find myself asking “Aren’t they all based on Linux..?” In this context, what exactly does it mean for one Linux OS to be based on another Linux OS? So, what exactly does it mean when we talk about one version of Linux being based off another version? The Answer SuperUser contributor kostix offers a solid overview of the whole system: Linux is a kernel — a (complex) piece of software which works with the hardware and exports a certain Application Programming Interface (API), and binary conventions on how to precisely use it (Application Binary Interface, ABI) available to the “user-space” applications. Debian, RedHat and others are operating systems — complete software environments which consist of the kernel and a set of user-space programs which make the computer useful as they perform sensible tasks (sending/receiving mail, allowing you to browse the Internet, driving a robot etc). Now each such OS, while providing mostly the same software (there are not so many free mail server programs or Internet browsers or desktop environments, for example) differ in approaches to do this and also in their stated goals and release cycles. Quite typically these OSes are called “distributions”. This is, IMO, a somewhat wrong term stemming from the fact you’re technically able to build all the required software by hand and install it on a target machine, so these OSes distribute the packaged software so you either don’t need to build it (Debian, RedHat) or they facilitate such building (Gentoo). They also usually provide an installer which helps to install the OS onto a target machine. Making and supporting an OS is a very complicated task requiring a complex and intricate infrastructure (upload queues, build servers, a bug tracker, and archive servers, mailing list software etc etc etc) and staff. This obviously raises a high barrier for creating a new, from-scratch OS. For instance, Debian provides ca. 37k packages for some five hardware architectures — go figure how much work is put into supporting this stuff. Still, if someone thinks they need to create a new OS for whatever reason, it may be a good idea to use an existing foundation to build on. And this is exactly where OSes based on other OSes come into existence. For instance, Ubuntu builds upon Debian by just importing most packages from it and repackaging only a small subset of them, plus packaging their own, providing their own artwork, default settings, documentation etc. Note that there are variations to this “based on” thing. For instance, Debian fosters the creation of “pure blends” of itself: distributions which use Debian rather directly, and just add a bunch of packages and other stuff only useful for rather small groups of users such as those working in education or medicine or music industry etc. Another twist is that not all these OSes are based on Linux. For instance, Debian also provide FreeBSD and Hurd kernels. They have quite tiny user groups but anyway. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• Windows Phone 8, possible tablets and what the latest update might mean

  - by Roger Hart

  Microsoft have just announced an update to Windows Phone 8. As one of the five, maybe six people who actually bought a WP8 handset I found this interesting. Then I read the blog post about it, and rushed off to write somewhat less than a thousand words about a single picture. The blog post announces an extra column of tiles on the start screen, and support for higher resolutions. If we ignore all the usual flummery about how this will make your life better, that (and the rotation lock) sounds a little like stage setting for tablets. Looking at the preview screenshot, I started to wonder. What it’s called Phablet_5F00_StartScreenProductivity_5F00_01_5F00_072A1240.jpg Pretty conclusive. If you can brand something a “phablet” and sleep at night you’re made of sterner stuff than I am, but that’s beside the point. It’s explicit in the post that Microsoft are expecting a broader range of form factors for WP8, but they stop short of quite calling out tablet size. The extra columns and resolution definitely back that up, so why stop at a 6 inch “phablet”? Sadly, the string of numbers there don’t really look like a Lumia model number – that would be a bit tendentious even for a speculative blog post about a single screenshot. “Productivity” is interesting too. I get into this a bit more below, but this is a pretty clear pitch for a business device. What it looks like Something that would look quite decent on a 7 inch screen, but something a bit too vertical to go toe-to-toe with the Surface. Certainly, it would look a lot better on a large-factor phone than any of the current models. Those tiles are going to get cramped and a bit ugly if the handsets aren’t getting bigger. What’s on it You have a bunch of missed calls, you rarely text, use a stocks app, and your budget spreadsheet and meeting notes are a thumb-reach away. Outlook is your main form of email. You care enough about LinkedIn to not only install its app but give it a huge live tile. There’s no beating about the bush here, the implicit persona is a corporate exec. With Nokia in the bag and Blackberry pushing daisies, that may not be a stupid play. There’s almost certainly a niche there if they can parlay their corporate credentials into filling it before BYOD (which functionally means an iPhone) reaches the late adopters. The really quite slick WP8 Office implementation ought to help here. This is the face they’ve chosen to present, the cultural milieu they’re normalizing for Windows Phone. It’s an iPhone for Serious Business Grown-ups. Could work, I guess. Does it mean anything? Is the latest WP8 update a sign that we can expect to see tablets running Windows Phone rather than WinRT? Well, WinRT tablets haven’t exactly taken off but I’m not quite going to make a leap like that just from a file name and a column of icons. I feel pretty safe, however, conjecturing that Microsoft would like to squeeze a WP8 “phablet” into the palm of every exec who’s ever grumbled about their Blackberry, and this release might get them a bit closer. If it works well incrementing up to larger devices, then that could be a fair hedge against WinRt crashing and burning any harder in the marketplace.

  Read the article

< Previous Page | 1 2 3 4 5 6  | Next Page >