Search Results

Search found 161 results on 7 pages for 'blade'.

Page 3/7 | < Previous Page | 1 2 3 4 5 6 7  | Next Page >

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• SQL Clustering on Hyper V - is a cluster within a cluster a benefit.

  - by Chris W

  This is a re-hash of a question I asked a while back - after a consultant has come in firing ideas in to other teams in the department the whole issue has been raised again hence I'm looking for more detailed answers. We're intending to set-up a multi-instance SQL Cluster across a number of physical blades which will run a variety of different systems across each SQL instance. In general use there will be one virtual SQL instance running on each VM host. Again, in general operation each VM host will run on a dedicated underlying blade. The set-up should give us lots of flexibility for maintenance of any individual VM or underlying blade with all the SQL instances able to fail over as required. My original plan had been to do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Within the VMs - create a failover cluster and then install SQL Server clustering. The consultant has suggested that we instead do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Create a cluster on the HOST machines which will host all the VMs. Within the VMs - create a failover cluster and then install SQL Server clustering. The big difference is the addition of step 4 whereby we cluster all of the guest VMs as well. The argument is that it improves maintenance further since we have no ties at all between the SQL cluster and physical hardware. We can in theory live migrate the guest VMs around the hosts without affecting the SQL cluster at all so we for routine maintenance physical blades we move the SQL cluster around without interruption and without needing to failover. It sounds like a nice idea but I've not come across anything on the internet where people say they've done this and it works OK. Can I actually do the live migrations of the guests without the SQL Cluster hosted within them getting upset? Does anyone have any experience of this set up, good or bad? Are there some pros and cons that I've not considered? I appreciate that mirroring is also a valuable option to consider - in this case we're favouring clustering since it will do the whole of each instance and we have a good number of databases. Some DBs are for lumbering 3rd party systems that may not even work kindly with mirroring (and my understanding of clustering is that fail overs are completely transparent to the clients). Thanks.

  Read the article

• links for 2010-12-10

  - by Bob Rhubart

  Oracle VM Blade Cluster Reference Configuration (InfraRed) "All components listed in the reference configuration have been tested together by Oracle, reducing the need for customer testing and the time-consuming and complex effort of designing and deploying a stable configuration." -- Ferhat Hatay (tags: oracle virtualization clustering) White Paper: Accelerating Deployment of Virtualized Infrastructures with the Oracle VM Blade Cluster Reference Configuration  The Oracle VM blade cluster reference configuration described in this paper provides a complete and fully tested virtualized stack that can reduce deployment time by weeks or months while also reducing risk and improving application performance. (tags: oracle otn virtualization infrastructure) White Paper: Best Practices and Guidelines for Deploying the Oracle VM Blade Cluster Reference Configuration This paper provides recommendations and best practices for optimizing virtualization infrastructures when deploying the Oracle VM blade cluster reference configuration.  (tags: oracle otn virtualization clustering) Your Most Familiar Processes - Rethink before using E2.0 | Enterprise 2.0 Blogs "Imagine what gains your organization could have by asking basic questions and reviewing your familiar processes before setting up even the most fundamental E2.0 technologies to support them!" -- John Brunswick (tags: oracle enterprise2.0 otn) Oracle's Global Single Schema (Oracle Master Data Management) "The success of all business processes depends on the availability of accurate master data. Clearly, the solution to this problem is to consolidate all the master data an organization uses to run its business." -- David Butler (tags: oracle otn mdm entarch businessprocess) One step further towards proven results: IT Strategies from Oracle Oracle ACE Douwe Pieter van den Bos shares his thoughts on "IT Strategies from Oracle" in this Google translation of his original Dutch post. (tags: oracle itso entarch) The Underground Oracle VM Manual Just in time for the holidays! Roddy Rodstein's epic 354-page manual is now available in a single pdf.. (tags: oracle otn virtualization oraclevm)

  Read the article

• Virutal Machine loses network connectivity on Hyper V

  - by Chris W

  We're running a number of VMs on a 6 node failover cluster of blades using Hyper V. We have an intermittent issue (every few days at different times - not a fixed frequency) of VMs losing network connectivity. Console access to the VM suggests all is fine and the underlying blade has normal connectivity. To resolve the problem we either have to re-start the VM or, more usually, we do a live migration to another blade which fires up connectivity and we then migrate it back to the original blade. I've had 3 instances of this happen with a specific VM running on a particular blade however it has happened once with a different VM running on a different blade. All VMs and blades have the same basic setup and are running Windows 2008 R2. Any ideas where I should be looking to diagnose the possible causes of this problem as the event logs provide no help?

  Read the article

• Brocade 200E Switch - Fibre Channel

  - by Arthor

  What I have: Fujitsu-Siemens PRIMERGY BX600 Brocade 200E (16 port, 4gbit fibre). My question: Imagine a QNAP with a fiber 10GBIT card connected to the Brocade 200E (16 port, 4gbit fibre). Would this work; would the card drop down to 4GBIT? Are 10GBIT fiber cards backwards completable. Update. I have the specs of my server now.... Fujitsu-Siemens PRIMERGY BX600 S3 Blade Ecosystem Blade Chassis comprising; 2 x A3C40073243 Blade Management modules 2 x A3C40089238 GBE Switch Blade SB9F 30/12 2 x A3C40085736 4Gb 10 port pass through blades 1 x A3C40083767 Digital KVM Modules 2 x A3C40073245 Fan enclosures + cooling fans 4 x A3C40073262 Power Supplies My Goals and Objectives To have a blade system in place for 8 blades for video rendering, the other 2 for database and scripts etc The system will be built on VMWARE ESXi 5 Use ISCSI on the QNAP to support HA and vmotion if needed Users to access the qnap for video editing QANAP has 12 drive (2 x (6 HDD in RAID 10)

  Read the article

• Virutal Machine loses network connectivity on Hyper V Cluster

  - by Chris W

  We're running a number of VMs on a 6 node failover cluster of blades using Hyper V. We have an intermittent issue (every few days at different times - not a fixed frequency) of VMs losing network connectivity. Console access to the VM suggests all is fine and the underlying blade has normal connectivity. To resolve the problem we either have to re-start the VM or, more usually, we do a live migration to another blade which fires up connectivity and we then migrate it back to the original blade. I've had 3 instances of this happen with a specific VM running on a particular blade however it has happened once with a different VM running on a different blade. All VMs and blades have the same basic setup and are running Windows 2008 R2. Any ideas where I should be looking to diagnose the possible causes of this problem as the event logs provide no help? Edit: I've checked that each blade is running the latest NIC drivers and all seem to be fine. Something that is confusing me - a failover or restart of the VM resolves the issue. Whilst I need to work out the underlying issue that is causing the NICs to hang I'm also concerned that the VM didn't failover to another node which would have solved the outage for me. Is there a way to configure the cluster so that it can tell that the VM guest has lost connectivity and fail it over? As things stand the cluster is assuming that the VM is running happily as I presume Hyper V says everything is great even though there is a problem.

  Read the article

• Reset DRAC/MC password on Dell BladeCentre 1855

  - by Farseeker

  I have a Dell Blade Centre 1855, and nobody knows what the root password for the DRAC/MC card in the blade chassis is (I tried root/calvin). I do not have IP access to the DRAC/MC, nor do I have physical access to the back of the blade centre to access the DRAC/MC module. I do have serial access (and can see the login prompt in hyperterm). I do have physical access to the FRONT of the chassis (the back of the cabinet is locked and lo-and-behold the key cannot be found). Does anyone know how to reset the password? Every piece of literature I find on the internet tells me I need to log in, or run racadm on the host machine (which I can't, because it's inside a blade chassis). If someone does know how to do it with physical access to the back of the bladecentre, please post it anyway, as I'm sure I'll get access to the back of the cabinet one day)

  Read the article

• Using two joysticks in Cocos2D

  - by Blade

  Here is what I am trying to do: With the left joystick the player can steer the figure and with the right joystick it can attack. Problem is that the left joystick seems to get all the input, the right one does not even register anything. I enabled multipletouch after the eagleView and gone thoroughly over the code. But I seem to miss something. I initiliaze both sticks and it shows me both of them in game, but like I said, only the left one works. I initialize them both. From the h. file: SneakyJoystick *joystick; SneakyJoystick *joystickRight; And in m.file I synthesize, deallocate and initialize them. In order to use one for controlling and the other for attacking I put this: -(void)updateStateWithDeltaTime:(ccTime)deltaTime andListOfGameObjects:(CCArray*)listOfGameObjects { if ((self.characterState == kStateIdle) || (self.characterState == kStateWalkingBack) || (self.characterState == kStateWalkingLeft) || (self.characterState == kStateWalkingRight)|| (self.characterState == kStateWalkingFront) || (self.characterState == kStateAttackingFront) || (self.characterState == kStateAttackingBack)|| (self.characterState == kStateAttackingRight)|| (self.characterState == kStateAttackingLeft)) { if (joystick.degrees > 60 && joystick.degrees < 120) { if (self.characterState != kStateWalkingBack) [self changeState:kStateWalkingBack]; }else if (joystick.degrees > 1 && joystick.degrees < 59) { if (self.characterState != kStateWalkingRight) [self changeState:kStateWalkingRight]; } else if (joystick.degrees > 211 && joystick.degrees < 300) { if (self.characterState != kStateWalkingFront) [self changeState:kStateWalkingFront]; } else if (joystick.degrees > 301 && joystick.degrees < 360){ if (self.characterState != kStateWalkingRight) [self changeState:kStateWalkingRight]; } else if (joystick.degrees > 121 && joystick.degrees < 210) { if (self.characterState != kStateWalkingLeft) [self changeState:kStateWalkingLeft]; } if (joystickRight.degrees > 60 && joystickRight.degrees < 120) { if (self.characterState != kStateAttackingBack) [self changeState:kStateAttackingBack]; }else if (joystickRight.degrees > 1 && joystickRight.degrees < 59) { if (self.characterState != kStateAttackingRight) [self changeState:kStateAttackingRight]; } else if (joystickRight.degrees > 211 && joystickRight.degrees < 300) { if (self.characterState != kStateAttackingFront) [self changeState:kStateAttackingFront]; } else if (joystickRight.degrees > 301 && joystickRight.degrees < 360){ if (self.characterState != kStateAttackingRight) [self changeState:kStateAttackingRight]; } else if (joystickRight.degrees > 121 && joystickRight.degrees < 210) { if (self.characterState != kStateAttackingLeft) [self changeState:kStateAttackingLeft]; } [self applyJoystick:joystick forTimeDelta:deltaTime]; [self applyJoystick:joystickRight forTimeDelta:deltaTime]; } Maybe it has something to do with putting them both to time delta? I tried working around it, but it did not work. So I am thankful for any input you guys can give me :)

  Read the article

• Cocos2D: Change animation based on joystick direction

  - by Blade

  I'm trying to get my figure to look in the right directions, based on the input of the joystick. So if I tilt left it looks left and the left animation is used, if I used right, it looks right and right animation is used, if up, then up, down, down and so on. I just get animation for front and back. Also if I press up I see the back of the figure correctly, but it won't go back into the original state when I don't press up anymore. -(void)applyJoystick:(SneakyJoystick *)aJoystick forTimeDelta:(float) deltaTime { CGPoint scaledVelocity = ccpMult(aJoystick.velocity, 128.0f); CGPoint oldPosition = [self position]; CGPoint newPosition = ccp(oldPosition.x + scaledVelocity.x * deltaTime, oldPosition.y + scaledVelocity.y * deltaTime); [self setPosition:newPosition]; id action = nil; int extra = 50; if ((int) aJoystick.degrees > 180 - extra && aJoystick.degrees < 180 + extra) { action = [CCAnimate actionWithAnimation:walkingAnimLeft restoreOriginalFrame:NO]; } else if ((int) aJoystick.degrees > 360 - extra && aJoystick.degrees < 360 + extra) { action = [CCAnimate actionWithAnimation:walkingAnimRight restoreOriginalFrame:NO]; } else if ((int) aJoystick.degrees > 90 - extra && aJoystick.degrees < 90 + extra) { action = [CCAnimate actionWithAnimation:walkingAnimBack restoreOriginalFrame:NO]; } else if ((int) aJoystick.degrees > 270 - extra && aJoystick.degrees < 270 + extra) { action = [CCAnimate actionWithAnimation:walkingAnimFront restoreOriginalFrame:NO]; } if (action != nil) { [self runAction:action]; } } }

  Read the article

• VSS error 521 when attempting backup

  - by blade

  Hi, I have backupassist and I attempt to run a backup, with VSS service running. However, I get this error in Windows Event Log: The backup operation that started at '?2010?-?04?-?30T01:51:15.601000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '2155348129'. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved. Code: 521. The error in backupassist is: The backup operation stopped before completing. Detailed error: ERROR - A Volume Shadow Copy Service operation error has occurred: (0x80042336) The writer experienced a partial failure. Check the component level error state for more information. Log of files successfully backed up: C:\Windows\Logs\WindowsServerBackup\Backup-29-04-2010_18-51-15.log Log of files for which backup failed: C:\Windows\Logs\WindowsServerBackup\Backup_Error-29-04-2010_18-51-15.log A Volume Shadow Copy Service operation failed. Please check "VSS" and "SPP" application event logs for more information. ERROR - A Volume Shadow Copy Service operation error has occurred: (0x80042336) The writer experienced a partial failure. Check the component level error state for more information. Any idea how to fix this? I work in a company with server engineers, they all state of having no problems with 2008 and VSS (though in the company we use predominantly 2003). Without vss working, I assume no backup application will work? Thanks

  Read the article

• BackupExec errors when starting services

  - by blade

  Hi, I've installed backupexec 2010 trial on my server, with an appropriately-privileged AD account, but get errors when starting the required services from the login page: Processing services Start services on server: WIN-HQ7JSCRTTSQ Starting Enterprise Vault Admin Service on WIN-HQ7JSCRTTSQ. The service Enterprise Vault Admin Service is already running on WIN-HQ7JSCRTTSQ. Starting Backup Exec Remote Agent for Windows Systems on WIN-HQ7JSCRTTSQ. The service Backup Exec Remote Agent for Windows Systems is already running on WIN-HQ7JSCRTTSQ. Starting Backup Exec Device & Media Service on WIN-HQ7JSCRTTSQ. Error starting the service Backup Exec Device & Media Service on WIN-HQ7JSCRTTSQ. Service-specific error code returned: 0x2000e2d3 (536928979) Starting Backup Exec Server on WIN-HQ7JSCRTTSQ. Error starting the service Backup Exec Server on WIN-HQ7JSCRTTSQ. The dependency service or group failed to start. Starting Backup Exec Job Engine on WIN-HQ7JSCRTTSQ. Error starting the service Backup Exec Job Engine on WIN-HQ7JSCRTTSQ. The dependency service or group failed to start. Starting Backup Exec Agent Browser on WIN-HQ7JSCRTTSQ. Error starting the service Backup Exec Agent Browser on WIN-HQ7JSCRTTSQ. The dependency service or group failed to start. Starting Backup Exec DLO Administration Service on WIN-HQ7JSCRTTSQ. Error starting the service Backup Exec DLO Administration Service on WIN-HQ7JSCRTTSQ. Error code returned: Starting Backup Exec DLO Maintenance Service on WIN-HQ7JSCRTTSQ. The service Backup Exec DLO Maintenance Service is already running on WIN-HQ7JSCRTTSQ. Starting Backup Exec Web Service on WIN-HQ7JSCRTTSQ. The service Backup Exec Web Service is already running on WIN-HQ7JSCRTTSQ. Start services on server WIN-HQ7JSCRTTSQ completed. Processing services completed! How can I resolve this?

  Read the article

• The OTN Garage Blog Week in Review

  - by Rick Ramsey

  In case you missed the last few blogs on the OTN Garage (because somebody neglected to cross-post them here), here they are: What Day Is It and Why Am I Wearing a Little Furry Skirt? - Oracle VM Templates, Oracle Linux, Wim Coekaerts, and jet lag. A Real Cutting Edge - Oracle Sun blade systems architecture, Blade Clusters, and best practices. Which Version of Solaris Were You Running When ... - Oracle Solaris Legacy Containers and the Voyager 1 Content Cluster: Understanding the Local Boot Option in the Automatic Installer of Oracle Solaris 11 Express - Resources to help you understand this cool option Rick - System Admin and Developer Community of the Oracle Technology Network

  Read the article

• Why is the vSphere console view so slow?

  - by blade

  Hi, Why is the Console view on the vSphere client so slow? It's a real shame because it's a shame to have to establish an RDP session every time you work on one of the VMs because of the speed of the console (I saw a tool to right click and open an RDP session to a VM in vSphere Client/ESX but this was not reliable). The Workstation console view is very smooth so I'd expect the vSphere Client console view to be very smooth. Thanks

  Read the article

• Improving RDP performance

  - by blade

  Hi, How can I improve RDP performance? I'm on an 8mb line, and I have disabled all the fancy features like visual styles. One page said if I set a low speed, that too will increase performance. Is there any proof in this? Also, there was an ad here about an application/technology which can increase RDP performance by x20. Has anyone used this? Thanks

  Read the article

• links for 2010-04-07

  - by Bob Rhubart

  James McGovern: Enterprise Architecture and Social CRM "With a few exceptions, the vast majority of enterprise architects I know spend an awful lot of time focused on internal issues whether it is rationalization, the cloud, storage governance, data center consolidation, creation of reference architectures, portfolio management and other considerations that aren’t even visible to customers. One should ask whether IT can be truly successful if we are busy listening to the business but otherwise are blissfully ignorant towards the customers they serve." -- James McGovern (tags: enterprisearchitecture crm socialcomputing) WRF Benchmark: X6275 Beats Power6 - BestPerf "Oracle's Sun Blade X6275 cluster is 28% faster than the IBM POWER6 cluster on Weather Research and Forecasting (WRF) continental United Status (CONUS) benchmark datasets. The Sun Blade X6275 cluster used a Quad Data Rate (QDR) InfiniBand connection along with Intel compilers and MPI." (tags: oracle sun x6275 benchmarks)

  Read the article

• BackupExec Hyper-V availability (within BackupExec 2010 or seperate?)

  - by blade

  Hi, I have downloaded the trial of Symantec BackupExec 2010 but I am a little confused: The agent for Hyper-V is available and for sale ($1800 or something), but the trial of BackupExec tells me i can install the agents I need from the installer. Can I install a full version of BackupExec, providing I have the license, but also install a full version of the Hyper-V agent? Or do I have to download/buy this seperately? Is a trial version available for the agents? As is probably obvious from this thread, I am a bit confused about the business model of this product. Please clarify. Thanks

  Read the article

• Forefront 2010 as my firewall solution, suitable?

  - by blade

  Hi, I need to lock down my Windows Server. Is Forefront 2010 ideal for my circumstances? These are: -I am the single user of my server -I RDP from other machines (eg the laptop). -I currently have no solution/using windows firewall (how good is this?). Thanks

  Read the article

• Cannot resolve Hostname to IP, but IP to hostname works

  - by blade

  Hi, I have deployed a bunch of windows server VMs on a cloud hosting service. These machines are all joined to a domain controller on the same service, which also hosts DNS. All of the domain-joined machines have dynamic IP (along with the DC). If I try to resolve any of the hostnames remotely, it fails. For example, I am in SQL Server Reporting Services and I need to connect to a remote server. I provide the hostname of the desired target server and this fails, but then if I provide the IP, this works. How can I pass the hostname and have this resolve to IP? Is there anything I need to look for in the DNS server? It has records of the hostnames (in forward lookup I think), but reverse is empty. Isn't it the case that forward lookup resolves ip to hostname and reverse resolves hostname to ip? Also, I don't know what he subnet mask because this is not in my control, so the machines may not be in the same subnet - can this be a cause of the problem? Where is the problem? Thanks

  Read the article

• Forgotten account password

  - by blade

  I kept my passwords recorded but the location on my PC where I kept this went missing. I now can't get into Windows Server 2008 R2 as I can't remember the administrator or named account credentials and have no password reset disk. This is on a VM (VM Player - which btw is temp till I get Hyper-V). How can I get back in? If I make AD can I join the server to AD and then set a domain account?

  Read the article

• Is defragging right for me?

  - by blade

  Hi, I am using Hyper-V on my Windows Server 2008 R2 DC x64 machine. I am also using standard SATA drives. I read some threads on here about defraging but could not reach a conclusion about whether or not I should use defragging. Can anyone shed some light on whether this will be right for me? Furthermore, what tool is best? There seems to be 3: http://www.perfectdisk.com/products/business-perfectdisk11-server/key-features http://www.diskeeper.com/diskeeper/home/server-edition.aspx?id=40279&wid=7 http://www.perfectdisk.com/products/business-perfectdisk11-hyper-v/learn-more Anyone have experience with this?

  Read the article

• Convert VM running on Linux hypervisor to OVF/VMDK

  - by blade

  Hi, I have a bunch of VMs on a Linux hypervisor (cloudsigma.com to be precised). I want to convert these to deploy to an ESX hypervisor (opsource cloud server), but need to create an ovf with the vmdk. I don't have access to the hypervisor of either service but opsource allow me to import ovf/vmdk so this is possible. What tool can create an ovf (With vmdk) of a Windows OS? I am not sure if VCenter Converter would work as it requires access to the hypervisor, if I remember correctly. I am hoping for something like vhd2disk which will create a .vhd of the currently running, parent Windows OS on a system. Thanks

  Read the article

• Windows HPC Server 08 suitability for Matlabs

  - by blade

  I want to setup another Hyper-V VM for installing Matlabs/doing some compute-intensive programming using C. I keep thinking that Windows Server HPC 2008 is designed for this sort of work. Would I be on the right track to setup a single VM with this OS and install this software? Or is HPC more for grid/distributed computing? Thanks

  Read the article

• Sudden complaint that Windows is not genuine - some questions

  - by blade

  Hi, I used to use VMWare Workstation and made several VMs with Win Server 2008, which worked fine. My first tasks were to setup RDP, updates, and activate the OS. I deleted Workstation and thus did not have my VMs available to use for about 2 months. Now I have VMWare Server 2.0.2 as I this is free and I am going to get Hyper-V on a host Win Server in about March, but when I have accessed one of my VMs (haven't tried the others yet), it complains that the copy of Windows is not genuine. I now have a black screen but can access all my apps on the VM. Will the OS eventually shut me out from accessing it? I got my key from the Action Pack but the standard R2 key has been taken down and replaced with the Enteprise R2 key. I have Enterprise R2 but apparently the autorun is corrupt! Thanks

  Read the article

• Free batch image watermarking software

  - by Blade

  Hi everyone. I'm looking for a simple yet effective software to watermark a lot of photos in batch. I have to apply a transparent png watermark image on 400 photos. The program have to place the watermark at a custom position relative to the bottom right corner of every picture. I would have done this in photoshop, but the scriptable action doesn't allow me to do conditionnal placing if the photo is portrait or landscape. I'm looking for a free lightweigh program. Thank you !

  Read the article

• How can I move an existing VM's files to a new directory in the same datastore?

  - by blade

  Hi, I have some VMs deployed on ESX. In vSphere 4, I want to move these VMs into another directory in the datastore. So the VM directories are under root, but I want them in root/MyNewFolder. I tried this by turning off a VM, copying the VM's file (VMDK etc) into the directory I want, deleting the hard drive from the VM's settings, adding a new hard drive and then selecting the new path to the VMDK. When I press ok on the settings dialog box, having made this modification to the settings, I get the following error: not found. What I am trying to do also does not seem to be possible when making a new VM. I can only make VMs under root.

  Read the article

< Previous Page | 1 2 3 4 5 6 7  | Next Page >