Search Results

Search found 133 results on 6 pages for 'conner bw'.

Page 3/6 | < Previous Page | 1 2 3 4 5 6  | Next Page >

• Can't configure frame relay T1 on Cisco 1760

  - by sonar

  For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

  Read the article

• Google app engine issue 777 particular solution?

  - by Niklas R

  I use 64.202.189.170 (godaddy) for a HTTP access to a www...on google app engine like GAE issue 777 so that a blank subdomain forwards to www.domain I get the blank to respond by output "This website is temporarily unavailable, please try again later. " There's info about this issue here http://knol.google.com/k/google-apps-discussion-group#view and here http://code.google.com/p/googleappengine/issues/detail?id=777 Since I managed to do it with a .com domain (The godaddy DNS hosted gralumo.com correctly responds to www..) I now want to do it with an off-site DNS managed domain getting the following info about servers: $ ping montao.com.br PING montao.com.br (64.202.189.170) 56(84) bytes of data. 64 bytes from pwfwd-v01.prod.mesa1.secureserver.net (64.202.189.170): icmp_seq=1 ttl=113 time=188 ms 64 bytes from pwfwd-v01.prod.mesa1.secureserver.net (64.202.189.170): icmp_seq=2 ttl=113 time=188 ms ^C --- montao.com.br ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 188.459/188.692/188.926/0.493 ms ubuntu@ubuntu:~$ ping www.montao.com.br PING ghs.l.google.com (74.125.43.121) 56(84) bytes of data. 64 bytes from bw-in-f121.1e100.net (74.125.43.121): icmp_seq=1 ttl=56 time=30.2 ms 64 bytes from bw-in-f121.1e100.net (74.125.43.121): icmp_seq=2 ttl=56 time=28.0 ms 64 bytes from bw-in-f121.1e100.net (74.125.43.121): icmp_seq=3 ttl=56 time=24.2 ms ^C --- ghs.l.google.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2003ms rtt min/avg/max/mdev = 24.201/27.522/30.282/2.514 ms So it looks to me these are the same IP numbers whether or not it's off-site DNS. It's just that it works for one domain and not the other. Could it be just resetting the appspot app ie removing and adding it? Can you recommend how to proceed? Thanks in advance

  Read the article

• Robotium - Write to file in eclipse workspace or computer file system

  - by Flavio Capaccio

  I'm running some tests using Robotium on an Android application that interacts with a web-portal. I'd like to save some information to file; for example I need to save the id of the username I created from the app and I want to make it read from Selenium to run tests on web-portal to verify a webpage for that user has been created. Is it possible? Could someone suggest me a solution or a work-around? This is an example of code, but it doesn't work (I want to write to a file for example on c:\myworkspace\filename.txt a string): public void test_write_file(){ if(!solo.searchText("HOME")){ signIn("39777555333", VALID_PASSWORD); } try { String content = "This is the content to write into file"; File file = new File("filename.txt"); // if file doesnt exists, then create it if (!file.exists()) { file.createNewFile(); } FileWriter fw = new FileWriter(file.getAbsoluteFile()); BufferedWriter bw = new BufferedWriter(fw); bw.write(content); bw.close(); } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } assertTrue(solo.searchText("HOME")); }

  Read the article

• C# Error reading two dates from a binary file

  - by Jamie

  Hi all, When reading two dates from a binary file I'm seeing the error below: "The output char buffer is too small to contain the decoded characters, encoding 'Unicode (UTF-8)' fallback 'System.Text.DecoderReplacementFallback'. Parameter name: chars" My code is below: static DateTime[] ReadDates() { System.IO.FileStream appData = new System.IO.FileStream( appDataFile, System.IO.FileMode.Open, System.IO.FileAccess.Read); List<DateTime> result = new List<DateTime>(); using (System.IO.BinaryReader br = new System.IO.BinaryReader(appData)) { while (br.PeekChar() > 0) { result.Add(new DateTime(br.ReadInt64())); } br.Close(); } return result.ToArray(); } static void WriteDates(IEnumerable<DateTime> dates) { System.IO.FileStream appData = new System.IO.FileStream( appDataFile, System.IO.FileMode.Create, System.IO.FileAccess.Write); List<DateTime> result = new List<DateTime>(); using (System.IO.BinaryWriter bw = new System.IO.BinaryWriter(appData)) { foreach (DateTime date in dates) bw.Write(date.Ticks); bw.Close(); } } What could be the cause? Thanks

  Read the article

• TypeError when using v 0.8.1 of FLOT library, but no error with v. 0.7

  - by DanielAttard

  I need some help to figure out why I am getting an error when trying to create a simple graph using the jQuery FLOT library. When I reference version 0.7 of the FLOT library, the page renders correctly: http://attardpropertytax.ca/flot07.html But when I switch to version 0.8.1 of the FLOT library, the page returns an error saying: Uncaught TypeError: Cannot read property 'left' of null http://attardpropertytax.ca/flot81.html The HTML is the same for both pages, so I cannot figure out why the new version 0.8.1 of FLOT returns an error, but the old version 0.7 does not. Any ideas? I somehow stumbled across a work-around that managed to fix my problem. I'm nut sure why, but I had to comment-out the following two sections of code from the v. 0.8.1 FLOT library: This was the first spot: // If the grid is visible, add its border width to the offset for (var a in plotOffset) { if(typeof(options.grid.borderWidth) == "object") { plotOffset[a] += showGrid ? options.grid.borderWidth[a] : 0; } else { plotOffset[a] += showGrid ? options.grid.borderWidth : 0; } } And this was the second spot: if (isNaN(v) || v < axis.min || v > axis.max // skip those lying on the axes if we got a border || (t == "full" && ((typeof bw == "object" && bw[axis.position] > 0) || bw > 0) && (v == axis.min || v == axis.max))) continue; I'm sure eventually @DNS will be taking a look at this question and maybe he will be able to help me understand what is going wrong with my code. Thanks.

  Read the article

• Java variables across methods

  - by NardCake

  I'm making a basic text editor, and I have 2 methods the first one is triggered when a user click 'Open' and it prompts the user to pick a file and it opens the file fine. I just want to access the same file path which is in a variable in the method that is triggered when the user clicks save. My methods are public, Iv'e tried accessing it through a class, still no. Please help! Code: public void open(){ try{ //Open file JFileChooser fc = new JFileChooser(); fc.showOpenDialog(null); File file = fc.getSelectedFile(); String haha = file.getPath(); BufferedReader br = new BufferedReader(new FileReader(file.getPath())); String line; while((line = br.readLine()) != null){ text.append(line + "\n"); } } catch (FileNotFoundException e){ e.printStackTrace(); }catch (IOException e){ } } public void save(){ try { BufferedWriter bw = new BufferedWriter(new FileWriter(file.filePath)); bw.write(text.getText()); bw.close(); } catch (IOException e) { e.printStackTrace(); } }

  Read the article

• Improve performance on Lync desktop sharing

  - by Trikks

  I'm using Lync 2010 server to handle some clients communication and screen sharing. The biggest issue is the performance with screen sharing, it is of rather high quality but the frame rate is very poor. I have been reading and searching a lot on the subject and 95% of all topics is about bandwidth, we have a 200/200 MBit Internet connection solely for this application. Also my test machines runs on an internal gigabit lan. The speeds between all boxes is hysterically fast. Next step was to ensure that there where some profiles for different bandwidths, so i registered some New-CsNetworkBandwidthPolicyProfile -Identity 50Mb_Link -Description "BW profile for 50Mb links" -AudioBWLimit 20000 -AudioBWSessionLimit 200 -VideoBWLimit 14000 -VideoBWSessionLimit 700 New-CsNetworkBandwidthPolicyProfile -Identity 100Mb_Link -Description "BW profile for 100Mb links" -AudioBWLimit 30000 -AudioBWSessionLimit 300 -VideoBWLimit 25000 -VideoBWSessionLimit 1500 Nothing fancy happend here either. Non of the test boxes have anything from Norton installed, they doesn't have any firewalls running (nor does the Lync server), all fences are down in this environment just for the testing. Is there any thing that I may have missed to improve the quality of this? Thanks

  Read the article

• How to close buffer without closing the window?

  - by progo

  I usually open a few windows and keep some buffers open. Since my MO in buffer exploring is to use quick shortcuts to :bn and :bp, I want to close unneeded buffers from distracting my buffer surfing. But the pain is, issuing :bd and :bw results in closing the window as well, in case I have multiple ones open. How do I close (delete) a buffer and leave the windows intact? Solution inspired by @peth's answer :command! BW :bn|:bd# It is simple. Doesn't work well with only one buffer open (I get different behaviour depending on the way I open the files) but it isn't a big issue. :)

  Read the article

• Why "Reader" link doesn't show in Gmail in chrome?

  - by ablmf

  I use both chrome and firefox at the same time. As I always open Gmail first and then use the Reader link in upper left conner of Gmail to open Google Reader, I noticed that chomre hides the Google Reader Link. I can't find it anywhere in Gmail. Why doesn't chrome behave differently?

  Read the article

• Inside BackgroundWorker

  - by João Angelo

  The BackgroundWorker is a reusable component that can be used in different contexts, but sometimes with unexpected results. If you are like me, you have mostly used background workers while doing Windows Forms development due to the flexibility they offer for running a background task. They support cancellation and give events that signal progress updates and task completion. When used in Windows Forms, these events (ProgressChanged and RunWorkerCompleted) get executed back on the UI thread where you can freely access your form controls. However, the logic of the progress changed and worker completed events being invoked in the thread that started the background worker is not something you get directly from the BackgroundWorker, but instead from the fact that you are running in the context of Windows Forms. Take the following example that illustrates the use of a worker in three different scenarios: – Console Application or Windows Service; – Windows Forms; – WPF. using System; using System.ComponentModel; using System.Threading; using System.Windows.Forms; using System.Windows.Threading; class Program { static AutoResetEvent Synch = new AutoResetEvent(false); static void Main() { var bw1 = new BackgroundWorker(); var bw2 = new BackgroundWorker(); var bw3 = new BackgroundWorker(); Console.WriteLine("DEFAULT"); var unspecializedThread = new Thread(() => { OutputCaller(1); SynchronizationContext.SetSynchronizationContext( new SynchronizationContext()); bw1.DoWork += (sender, e) => OutputWork(1); bw1.RunWorkerCompleted += (sender, e) => OutputCompleted(1); // Uses default SynchronizationContext bw1.RunWorkerAsync(); }); unspecializedThread.IsBackground = true; unspecializedThread.Start(); Synch.WaitOne(); Console.WriteLine(); Console.WriteLine("WINDOWS FORMS"); var windowsFormsThread = new Thread(() => { OutputCaller(2); SynchronizationContext.SetSynchronizationContext( new WindowsFormsSynchronizationContext()); bw2.DoWork += (sender, e) => OutputWork(2); bw2.RunWorkerCompleted += (sender, e) => OutputCompleted(2); // Uses WindowsFormsSynchronizationContext bw2.RunWorkerAsync(); Application.Run(); }); windowsFormsThread.IsBackground = true; windowsFormsThread.SetApartmentState(ApartmentState.STA); windowsFormsThread.Start(); Synch.WaitOne(); Console.WriteLine(); Console.WriteLine("WPF"); var wpfThread = new Thread(() => { OutputCaller(3); SynchronizationContext.SetSynchronizationContext( new DispatcherSynchronizationContext()); bw3.DoWork += (sender, e) => OutputWork(3); bw3.RunWorkerCompleted += (sender, e) => OutputCompleted(3); // Uses DispatcherSynchronizationContext bw3.RunWorkerAsync(); Dispatcher.Run(); }); wpfThread.IsBackground = true; wpfThread.SetApartmentState(ApartmentState.STA); wpfThread.Start(); Synch.WaitOne(); } static void OutputCaller(int workerId) { Console.WriteLine( "bw{0}.{1} | Thread: {2} | IsThreadPool: {3}", workerId, "RunWorkerAsync".PadRight(18), Thread.CurrentThread.ManagedThreadId, Thread.CurrentThread.IsThreadPoolThread); } static void OutputWork(int workerId) { Console.WriteLine( "bw{0}.{1} | Thread: {2} | IsThreadPool: {3}", workerId, "DoWork".PadRight(18), Thread.CurrentThread.ManagedThreadId, Thread.CurrentThread.IsThreadPoolThread); } static void OutputCompleted(int workerId) { Console.WriteLine( "bw{0}.{1} | Thread: {2} | IsThreadPool: {3}", workerId, "RunWorkerCompleted".PadRight(18), Thread.CurrentThread.ManagedThreadId, Thread.CurrentThread.IsThreadPoolThread); Synch.Set(); } } Output: //DEFAULT //bw1.RunWorkerAsync | Thread: 3 | IsThreadPool: False //bw1.DoWork | Thread: 4 | IsThreadPool: True //bw1.RunWorkerCompleted | Thread: 5 | IsThreadPool: True //WINDOWS FORMS //bw2.RunWorkerAsync | Thread: 6 | IsThreadPool: False //bw2.DoWork | Thread: 5 | IsThreadPool: True //bw2.RunWorkerCompleted | Thread: 6 | IsThreadPool: False //WPF //bw3.RunWorkerAsync | Thread: 7 | IsThreadPool: False //bw3.DoWork | Thread: 5 | IsThreadPool: True //bw3.RunWorkerCompleted | Thread: 7 | IsThreadPool: False As you can see the output between the first and remaining scenarios is somewhat different. While in Windows Forms and WPF the worker completed event runs on the thread that called RunWorkerAsync, in the first scenario the same event runs on any thread available in the thread pool. Another scenario where you can get the first behavior, even when on Windows Forms or WPF, is if you chain the creation of background workers, that is, you create a second worker in the DoWork event handler of an already running worker. Since the DoWork executes in a thread from the pool the second worker will use the default synchronization context and the completed event will not run in the UI thread.

  Read the article

• Rotate Body From Corner

  - by Siddharth

  I want to ask that how to rotate body from corner? movableBeam.getBeamBody().setTransform(movableBeam.getBeamBody().getPosition(), angle); The above line of code rotate the beam from center that I want rotate from one of the conner. Any member please help me. EDIT : float beamCenterX = movableBeam.getX() + movableBeam.getWidth() / 2f; float beamCenterY = movableBeam.getY() + movableBeam.getHeight() / 2f; float cornerOffsetX = movableBeam.getX() - beamCenterX; float cornerOffsetY = movableBeam.getY() - beamCenterY; float bodyAngle = (float) Math.atan2(cornerOffsetY, cornerOffsetX); float newAngle = imageAngle + bodyAngle; float newCornerOffsetX = (float) Math.cos(Math .toDegrees(newAngle)); float newCornerOffsetY = (float) Math.sin(Math .toDegrees(newAngle)); cornerOffsetX = movableBeam.getX() - movableBeam.getWidth() / 2f; cornerOffsetY = movableBeam.getY() - movableBeam.getHeight() / 2f; Vector2 postion = new Vector2( (newCornerOffsetX - cornerOffsetX + movableBeam.getX()) / PhysicsConstants.PIXEL_TO_METER_RATIO_DEFAULT, (newCornerOffsetY - cornerOffsetY + movableBeam.getY()) / PhysicsConstants.PIXEL_TO_METER_RATIO_DEFAULT); movableBeam.getBeamBody().setTransform(postion, newAngle);

  Read the article

• Long Running Stored Proc - Report Progress Using BackgroundWorker & Timer

  - by daveywc

  While a long running stored proc (RMR_Seek) is executing (called via a Linq-To-SQL data context) I am trying to call another stored proc (RMR_GetLatestModelMessage) to check a table for the latest status message. The long running stored proc updates the table in question with status messages as it executes. I want to display the status message on a message panel to advise the user of the status of the execution of Proc_A. For various reasons it is not possible to determine how long RMR_Seek will take to execute so a progress bar with percentage increments is not feasible. I thought I'd found the way to do it by calling the long running stored proc from in a BackgroundWorker process DoWork event handler. This worked fine and allowed me to update my message panel with some dummy status messages that were NOT obtained via Proc_B while Proc_A was running. However now that I have tried to implement this fully by calling Proc_B to obtain the status messages I am running into problems that seem to be related to the mix of the backgroundworker and my System.Windows.Forms.Timer. An extract of the code I am using is below. I have tried many different ways around this but each one seems to present its own set of problems. The code below is problematic in the bw_DoWork event. The RMR_Seek stored proc gets called but does not execute properly - it also seems to be inconsistent as to whether _IsCompleted gets set to true. I'm sure there is a better way to achieve what I am trying to do. private bool _IsCompleted; private void RunRevenueSeek() { if (_SelectedModel == null) { MessageBox.Show("Please select a model from the list and try again.", "Model Generation", MessageBoxButtons.OK, MessageBoxIcon.Information); } else { var bw = new BackgroundWorker(); bw.DoWork += new DoWorkEventHandler(bw_DoWork); ProgressPanelControl.Visible = true; _IsCompleted = false; MessageTimer.Start(); // Has an interval of 3000 bw.RunWorkerAsync(); ProgressLabelControl.Text = "Refreshing Data"; this.Update(); ...more code goes here } } private void bw_DoWork(object sender, DoWorkEventArgs e) { using (var dc = new RevMdlrDataClassesDataContext()) { dc.CommandTimeout = 300; dc.RMR_Seek(_SelectedModel.ModelSet_ID); _IsCompleted = true; } } private void MessageTimer_Tick(object sender, EventArgs e) { string message = ""; if (_IsCompleted) { MessageTimer.Stop(); } else { using (var dc = new RevMdlrDataClassesDataContext()) { dc.CommandTimeout = 300; dc.RMR_GetLatestModelMessage(_SelectedModel.ModelSet_ID, ref message); ProgressLabelControl.Text = message; this.Update(); } } }

  Read the article

• Why its not working?

  - by Andrew Hoffmann

  BinaryReader br = new BinaryReader(Console.OpenStandardInput()); BinaryWriter bw = new BinaryWriter(Console.OpenStandardOutput()); int n = br.ReadInt32(); bw.Write(n); always getting this error: Unhandled Exception: System.IO.EndOfStreamException: Failed to read past end of stream. at System.IO.BinaryReader.FillBuffer (Int32 numBytes) [0x00000] in <filename unknown>:0 at System.IO.BinaryReader.ReadInt32 () [0x00000] in <filename unknown>:0 at Program.Main () [0x00025] in /home/skydos/ACM/Csharp/Csharp/Main.cs:24 Is there any way to make reading data in C# faster from Console?

  Read the article

• Java BufferedWriter close()

  - by rakeshr

  Hi, assume that I have the following code fragment operation1(); bw.close(); operation2(); When I call BufferedReader.close() from my code, I am assuming my JVM makes a system call that ensures that the buffer has been flushed and written to disk. I want to know if close() waits for the system call to complete its operation or does it proceed to operation2() without waiting for close() to finish. To rephrase my question, when I do operation2(), can I assume that bw.close() has completed successfully?

  Read the article

• vim plugin to show current Perl subroutine

  - by Andrew

  I'm trying to make a vim plugin that will split the window on load and simulate a info bar at the top of my terminal. I've got it sorta working but I think I've either reached limits of my knowledge of vim syntax or there's a logic problem in my code. The desired effect would be to do a reverse search for any declaration of a Perl subroutine form my current location in the active buffer and display the line in the top buffer. I'm also trying to make it skip that buffer when I switch buffers with <C-R>. My attempt at that so far can be seen in the mess of nested if statements. Anyway, here's the code. I would greatly appreciate feedback from anyone. (pastebin pastebin.com/8cuMPn1Q) let s:current_function_bufname = 'Current\ Function\/Subroutine' function! s:get_current_function_name(no_echo) let lnum = line(".") let col = col(".") if a:no_echo let s:current_function_name = getline(search("^[^s]sub .$", 'bW')) else echohl ModeMsg echo getline(search("^[^s]sub .$", 'bW')) "echo getline(search("^[^ \t#/]\{2}.[^:]\s$", 'bW')) echohl None endif endfunction let s:previous_winbufnr = 1 let s:current_function_name = '' let s:current_function_buffer_created = 0 let s:current_function_bufnr = 2 function! s:show_current_function() let total_buffers = winnr('$') let current_winbufnr = winnr() if s:previous_winbufnr != current_winbufnr if bufname(current_winbufnr) == s:current_function_bufname if s:previous_winbufnr < current_winbufnr let i = current_winbufnr + 1 if i total_buffers let i = 1 endif if i == s:current_function_bufnr let i = i + 1 endif if i total buffers let i = 1 endif exec i.'wincmd w' else let i = current_winbufnr - 1 if i < 1 let i = total_buffers endif if i == s:current_function_bufnr let i = i - 1 endif if i < 1 let i = total_buffers endif try exec i.'wincmd w' finally exec total_buffers.'wincmd w' endtry endif endif let s:previous_winbufnr = current_winbufnr return 1 endif if s:current_function_buffer_created == 0 exec 'top 1 split '.s:current_function_bufname call s:set_as_scratch_buffer() let s:current_function_buffer_created = 1 let s:current_function_bufnr = winnr() endif call s:activate_buffer_by_name(s:current_function_bufname) setlocal modifiable call s:get_current_function_name(1) call setline(1, s:current_function_name) setlocal nomodifiable call s:activate_buffer_by_name(bufname(current_winbufnr)) endfunction function! s:set_as_scratch_buffer() setlocal noswapfile setlocal nomodifiable setlocal bufhidden=delete setlocal buftype=nofile setlocal nobuflisted setlocal nonumber setlocal nowrap setlocal cursorline endfunction function! s:activate_buffer_by_name(name) for i in range(1, winnr('$')) let name = bufname(winbufnr(i)) let full_name = fnamemodify(bufname(winbufnr(i)), ':p') if name == a:name || full_name == a:name exec i.'wincmd w' return 1 endif endfor return 0 endfunction set laststatus=2 autocmd! CursorMoved,CursorMovedI,BufWinEnter * call s:show_current_function() (pastebin pastebin.com/8cuMPn1Q) similar to VIM: display custom reference bar on top of window and http://vim.wikia.com/wiki/Show_current_function_name_in_C_programs

  Read the article

• Distributing a function over a single dimension of an array in MATLAB?

  - by Alex Feinman

  I often find myself wanting to collapse an n-dimensional matrix across one dimension, and can't figure out if there is a concise incantation I can use to do this. For example, when parsing an image, I often want to do something like this. (Note! Illustrative example only. I know about rgb2gray for this specific case.) img = imread('whatever.jpg'); s = size(img); for i=1:s(1) for j=1:s(2) bw_img = mean(img(i,j,:)); end end I would love to express this as something like: bw = on(color, 3, @mean); or bw(:,:,1) = mean(color); Is there a short way to do this?

  Read the article

• Media Streaming Server

  - by Ehsan

  I'm looking for a media stream server (specially audio streams) for installing on my Ubuntu server box. Is there any lightweight, easy configurable solution? It's awesome if this solution is able to install on a high bandwidth server and gets a stream from a low bandwidth server and serves it for many clients. (simply because the original server hasn't enough BW to serve media for many clients) (My server is a LAMP server, but I'm looking for a good solution for one of my clients to stream his audio for one hour every week)

  Read the article

• cannot install cinnimon 2.xx

  - by user207587

  Fetched 841 kB in 28s (29.3 kB/s) W: GPG error: http://packages.mate-desktop.org raring Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 68980A0EA10B4DE8 W: Failed to fetch http://ppa.launchpad.net/pmcenery/ppa/ubuntu/dists/raring/main/binary-i386/Packages 404 Not Found E: Some index files failed to download. They have been ignored, or old ones used instead. userx@bw:~$ How do I fix that? How do I add a PUBKEY to get needed files to complete install of Cinnamon?

  Read the article

• using pf for packet filtering and ipfw's dummynet for bandwidth limiting at the same time

  - by krdx

  I would like to ask if it's fine to use pf for all packet filtering (including using altq for traffic shaping) and ipfw's dummynet for bandwidth limiting certain IPs or subnets at the same time. I am using FreeBSD 10 and I couldn't find a definitive answer to this. Googling returns such results as: It works It doesn't work Might work but it's not stable and not recommended It can work as long as you load the kernel modules in the right order It used to work but with recent FreeBSD versions it doesn't You can make it work provided you use a patch from pfsense Then there's a mention that this patch might had been merged back to FreeBSD, but I can't find it. One certain thing is that pfsense uses both firewalls simultaneously so the question is, is it possible with stock FreeBSD 10 (and where to obtain the patch if it's still necessary). For reference here's a sample of what I have for now and how I load things /etc/rc.conf ifconfig_vtnet0="inet 80.224.45.100 netmask 255.255.255.0 -rxcsum -txcsum" ifconfig_vtnet1="inet 10.20.20.1 netmask 255.255.255.0 -rxcsum -txcsum" defaultrouter="80.224.45.1" gateway_enable="YES" firewall_enable="YES" firewall_script="/etc/ipfw.rules" pf_enable="YES" pf_rules="/etc/pf.conf" /etc/pf.conf WAN1="vtnet0" LAN1="vtnet1" set skip on lo0 set block-policy return scrub on $WAN1 all fragment reassemble scrub on $LAN1 all fragment reassemble altq on $WAN1 hfsc bandwidth 30Mb queue { q_ssh, q_default } queue q_ssh bandwidth 10% priority 2 hfsc (upperlimit 99%) queue q_default bandwidth 90% priority 1 hfsc (default upperlimit 99%) nat on $WAN1 from $LAN1:network to any -> ($WAN1) block in all block out all antispoof quick for $WAN1 antispoof quick for $LAN1 pass in on $WAN1 inet proto icmp from any to $WAN1 keep state pass in on $WAN1 proto tcp from any to $WAN1 port www pass in on $WAN1 proto tcp from any to $WAN1 port ssh pass out quick on $WAN1 proto tcp from $WAN1 to any port ssh queue q_ssh keep state pass out on $WAN1 keep state pass in on $LAN1 from $LAN1:network to any keep state /etc/ipfw.rules ipfw -q -f flush ipfw -q add 65534 allow all from any to any ipfw -q pipe 1 config bw 2048KBit/s ipfw -q pipe 2 config bw 2048KBit/s ipfw -q add pipe 1 ip from any to 10.20.20.4 via vtnet1 out ipfw -q add pipe 2 ip from 10.20.20.4 to any via vtnet1 in

  Read the article

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues...

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Why won't my service start, and why doesn't upstart output any errors?

  - by Alex Waters

  I am trying to 'start gunicorn' as a service via upstart as user ale. I'm using gunicorn/flask on ubuntu 12.04 w/ init (upstart 1.5) Here is my /etc/init/gunicorn.conf setuid btw setgid flask script export HOME=/home/btw export WORKON_HOME=$HOME/.virtualenvs . $HOME/.virtualenvs/default/bin/activate cd $HOME/flask workon default gunicorn -c gunicorn.py bw:app end script It doesn't output anything other than gunicorn start/running, process 12992. If i then do 'status gunicorn' I get stop/waiting. any ideas on how to debug this? I tried following http://upstart.ubuntu.com/wiki/Debugging but it didn't help. If I do the following as user ale in the app's directory: 1. workon default 2. gunicorn -c gunicorn.py bw:app then Gunicorn runs fine. Here is ~/flask/gunicorn.py: bind = "0.0.0.0:8080" workers = 3 backlog = 2048 worker_class = "gevent" debug = True daemon = False pidfile ="/tmp/gunicorn.pid" log_level = "debug" accesslog = "/var/log/gunicorn/access.log" errorlog = "/var/log/gunicorn/error.log" user = "btw" group = "flask" Also, /var/log/error.log doesn't show anything new when I try to start the Gunicorn service. If I start it manually, it shows that the workers have been loaded, etc. Thanks for any help / suggestions!

  Read the article

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• how to run this qt script? (newbie question)

  - by GB_J

  I have a qt script(barchart.qs) that creates a graph for me. I don't know how i can incorporate(ie show the graph) in my qt mainwindow. Can some one please help me look at the code and what its outputs are? I tried engine.evaluate, but i do not know what is the QScriptValue i'm getting in return. Thanks sooo much. This is the script: BarChart.prototype = new QWidget; BarChart.prototype.suffix = ""; function BarChart(parent) { QWidget.call(this, parent); } // find the maximum value and widest (pixel-wise) label and suffix BarChart.prototype.showEvent = function(event) { var fm = new QFontMetrics(this); this.margin = 20; this.titleHeight = fm.height(); this.barHeight = 1.5 * fm.height(); this.barSpacing = 0.6 * fm.height(); this.maxValue = this.suffixWidth = this.labelWidth = 0; var count = 0; for (d in this.data) { this.labelWidth = Math.max(this.labelWidth, fm.width(d)); this.maxValue = Math.max(this.maxValue, this.data[d]); this.suffixWidth = Math.max(this.suffixWidth, fm.width(String(this.data[d]) + " " + this.suffix)); count++; } this.startHue = 15; this.hueDelta = 360 / count; this.size = new QSize(640, this.titleHeight + 2 * this.margin + (this.barHeight + this.barSpacing) * count); } BarChart.prototype.paintEvent = function(event) { var p = new QPainter; p.begin(this); // background and title p.fillRect(this.rect, new QBrush(new QColor(255, 255, 255))); p.drawText(0, 0, this.width, this.margin + this.titleHeight, Qt.AlignCenter, this.windowTitle, 0); var ofs = this.labelWidth + this.margin; var ww = this.width - this.suffixWidth - ofs - 2 * this.margin; var hue = this.startHue; var y = 0; p.translate(this.margin, this.titleHeight + 1.5 * this.margin); for (d in this.data) { // label on the left side p.setPen(new QColor(Qt.black)); p.drawText(0, y, this.labelWidth, this.barHeight, Qt.AlignVCenter + Qt.AlignRight, d, 0); // the colored bar var gradient = new QLinearGradient(new QPoint(ofs, y), new QPoint(ofs, y + this.barHeight)); gradient.setColorAt(0, QColor.fromHsv(hue, 255, 240)); gradient.setColorAt(1, QColor.fromHsv(hue, 255, 92)); p.setBrush(new QBrush(gradient)); p.setPen(new QColor(96, 96, 96)); var bw = this.data[d] * ww / this.maxValue; p.drawRect(ofs, y, bw, this.barHeight); // extra text at the end of the bar var text = new String(this.data[d] + " " + this.suffix); p.setPen(new QColor(Qt.black)); p.drawText(ofs + bw + this.margin/2, y, this.suffixWidth, this.barHeight, Qt.AlignVCenter + Qt.AlignLeft, text, 0); // for the next bar y += (this.barHeight + this.barSpacing); hue += this.hueDelta; if (hue >= 360) hue -= 360; } p.end(); } BarChart.prototype.wheelEvent = function(event) { this.startHue += event.delta() / 8 / 5; if (this.startHue = 360) this.startHue -= 360; if (this.startHue < 0) this.startHue += 360; this.update(); event.ignore(); } BarChart.prototype.mousePressEvent = function(event) { var fname = QFileDialog.getSaveFileName(this, "Save", ".", "*.png", 0, 0); if (fname.length > 0) { var img = new QImage(this.size, QImage.Format_ARGB32_Premultiplied); this.render(img); img.save(new QFile(fname)); } } var chart = new BarChart; chart.windowTitle = "Monthly"; chart.suffix = "reports"; chart.data = { "September" : 45, "October" : 60, "November" : 56, "December" : 0 }; chart.show(); QCoreApplication.exec();

  Read the article

• JQuery Selector - Finding an img in a table

  - by CccTrash

  Cant seem to get the following to find the 'skull' button when the 'heart' button is clicked... Here is the JQuery... $(".voteup").click(function() { var id = $(this).attr("title"); var userID = $('[id$=HiddenFieldUserID]').val(); var ipAddress = $('[id$=HiddenFieldIPAddress]').val(); var skullButton = $(this).parent().siblings(".votedowntd").children("votedown"); registerUpVote("up", id, $(this), skullButton, userID, ipAddress); }); And the HTML... <table width="200px"> <td width="35px" class="votedowntd"> <img src='<%# (bool)Eval("skull") ? "images/skull.png" : "images/skull-bw.png" %>' alt="Vote Down" class="votedown" title='<%# Eval("entry.ID") %>' /> </td> <td width="130px" style="text-align: center;"> Num Votes Goes Here </td> <td width="35px" class="voteuptd"> <img src='<%# (bool)Eval("heart") ? "images/heart.png" : "images/heart-bw.png" %>' alt="Vote Up" class="voteup" title='<%# Eval("entry.ID") %>' /> </td> <tr> </tr> </table> So basically what I need to do is when one img is clicked, I need to find the other one. Why is what I have not working? Is there a better way to do this?

  Read the article

• How can I create an Image in GDI+ from a Base64-Encoded string in C++?

  - by Schnapple

  I have an application, currently written in C#, which can take a Base64-encoded string and turn it into an Image (a TIFF image in this case), and vice versa. In C# this is actually pretty simple. private byte[] ImageToByteArray(Image img) { MemoryStream ms = new MemoryStream(); img.Save(ms, System.Drawing.Imaging.ImageFormat.Tiff); return ms.ToArray(); } private Image byteArrayToImage(byte[] byteArrayIn) { MemoryStream ms = new MemoryStream(byteArrayIn); BinaryWriter bw = new BinaryWriter(ms); bw.Write(byteArrayIn); Image returnImage = Image.FromStream(ms, true, false); return returnImage; } // Convert Image into string byte[] imagebytes = ImageToByteArray(anImage); string Base64EncodedStringImage = Convert.ToBase64String(imagebytes); // Convert string into Image byte[] imagebytes = Convert.FromBase64String(Base64EncodedStringImage); Image anImage = byteArrayToImage(imagebytes); (and, now that I'm looking at it, could be simplified even further) I now have a business need to do this in C++. I'm using GDI+ to draw the graphics (Windows only so far) and I already have code to decode the string in C++ (to another string). What I'm stumbling on, however, is getting the information into an Image object in GDI+. At this point I figure I need either a) A way of converting that Base64-decoded string into an IStream to feed to the Image object's FromStream function b) A way to convert the Base64-encoded string into an IStream to feed to the Image object's FromStream function (so, different code than I'm currently using) c) Some completely different way I'm not thinking of here. My C++ skills are very rusty and I'm also spoiled by the managed .NET platform, so if I'm attacking this all wrong I'm open to suggestions.

  Read the article

< Previous Page | 1 2 3 4 5 6  | Next Page >