Search Results

Search found 15670 results on 627 pages for 'multi level'.

Page 3/627 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Acer 1420p: Screen Rotation does not always rotate multi-touch input

  - by Armen

  I have a PDC'09 Acer 1420p tablet with a multi-touch screen. Sometimes when I rotate the display, the multi-touch surface input does not rotate to match. The track pad rotates just fine, but not the screen input. Has anyone else run into this problem on the PDC laptop or any other machine? It uses Intel GMA 4500, running Windows 7 64.

  Read the article

• Graphics Cards - What is Multi View?

  - by Keith Nicholas

  I have been looking at graphics cards, and I notice that some of them feature 'Multi View', only I cannot find a definition of what it is? What is Multi-view and what is it used for? It is a vendor-specific feature (such as SLI)?

  Read the article

• Best practise for Progress Bar in Python's PyGTK

  - by Matthew Walker

  I would like to get feedback on others' opinions of best practice for how to implement a progress bar in Python's PyGTK. The work that the progress bar was to represent was very significant computationally. Therefore, I wanted the work to be done in a separate process (thus giving the operating system the possibility to run it on a different core). I wanted to be able to start the work, and then continue to use the GUI for other tasks while waiting for the results. I have seen many people asking this question indirectly, but I have not seen any concrete expert advice. I hope that by asking this question we will see a community's combined expertise. I have read the FAQ and I hope that "Programmers" is the right place to ask.

  Read the article

• Múltiples clientes en el mismo Oracle UCM

  - by [email protected]

  Estamos muy activos con la implantación de plataformas ECM que den servicio a múltiples clientes. Consiguiendo 2 objetivos muy importantes:El cliente final puede pagar al proveedor por una plataformas ECM como servicio (SaaS). Y, lógicamente, se ahorra en complejidad y gastos de infraestructura, administración, formación, almacenamiento, etc...Hemos estado explicando estos días el modelo Master-Proxy de Oracle UCM con el que podemos implantar este tipo de plataformas. No siempre será la solución más adecuada porque a veces vamos a querer disponer de plataformas compartidas, pero con clientes completamente aislados. Siempre, la consola de migración nos permite exportar e importar componentes, metadatos, contenidos, workflows, etc... para que elijamos el modelo más adecuado para cada caso.Pero, ¿Cómo funciona?. Podéis ver en la imágen que se basa en la instalación de varias instancias de UCM y configurarlas de forma que varias de ellas se comporten como "Master" (digo varias para conseguir alta disponibilidad), y el resto se comporten como "Proxy" (también varias instancias de UCM pueden comportarse como un mismo "Proxy" permitiendo balancear la carga en función de que cada cliente requiera más o menos rendimiento). Esta configuración (que vemos en la imágen adjunta), nos permite:Delegar la gestión de usuarios de cada cliente. Los usuarios del Master podrán acceder a todos los Proxies, pero los usuarios de cada proxy sólo acceden a su repositorio.Delegar funcionalidad y componentes. Es posible configurar diferentes funcionalidades en cada proxy de forma que algunos servidores estén especializados en Web Content Management, otros en Document Management (por ejemplo).Diferentes modelos de metadatos. Podemos modelar unos tipos documentales generales para toda la plataforma y otros particulares diferentes en cada UCM "Proxy".Conseguir una centralización de búsquedas y acceso a repositorios de documentación con diferentes juegos de caracteres. Un UCM Master puede centralizar la búsqueda en UCM's proxy que alberguen documentación en diferentes juegos de caracteres (por ejemplo un UCM para documentación de idiomas "Western European" (inglés, español, francés, alemán,...) y otro UCM proxy bajo juego de caracteres "Asian" (japones, coreano, chino,...).Fuentes:Toda la información detallada se encuentra en la documentación de Oracle UCM, aquí:http://download.oracle.com/docs/cd/E10316_01/ouc.htmY en concreto, lo relativo a plataformas, en el documento "Planning and Implementation Guide", aquí:plan_implement_guide_10en.pdf

  Read the article

• What threading pratice is good 90% of the time?

  - by acidzombie24

  Since my SO thread was closed i guess i can ask it here. What practice or practices are good 90% of the time when working with threading with multiple cores? Personally all i have done was share immutable classes and pass (copy) data to a queue to the destine thread. Note: This is for research and when i say 90% of the time i dont mean it is allowed to fail 10% of the time (thats ridiculous!) i mean 90% it is a good solution while the other 10% it is not so desirable due to implementation or efficiently reasons (or plainly another technique fits the problem domain a lot better).

  Read the article

• Level design - Are games development degrees worth it? [on hold]

  - by Tristan

  I want to go into Level design or Environment design and wondering if degrees are at all worth it for this area, as long as you have a good portfolio. I'm currently on a "Computing and Games Development" course and I feel like dropping out because I am not enjoying it. It's mostly computer based, which I'm not doing that great at, and little games Dev. But I don't know what do to... I do already have some high level education with a "Level 3 extended diploma". Thanks.

  Read the article

• Hibernate - moving annotations from property (method) level to field level

  - by kan

  How do I generate hibernate domain classes from tables with annotations at field level? I used Hibernate Tools project and generated domain classes from the tables in the database. The generated classes have annotations on the getter methods rather than at the field level. Kindly advice a way to generate domain classes that have the fields annotated. Is there any refactoring facility available in eclipse/IDEA etc.. to move the annotations from method level to field level? Appreciate your help and time.

  Read the article

• Determining the level of Android permission

  - by k4b

  I have some Android permissions which I would like to know to which permision PROTECTION LEVEL they belong. Does anybody know how can this be checked? For example I need to know the PROTECTION LEVEL of android.permission.RECEIVE_BOOT_COMPLETED permission, but I would like to check many more. EDIT: I see that I didn't put it clearly: What I mean is not an API level with which permission was introduced, but permission protection level, one of four: Normal, Dangerous, Signeture, SignatureOrSystem. It determines for example how this permision is presented to user during the application installation. How can I check to which protection level certain permission belongs?

  Read the article

• How do I simplify a 2D game grid for level management while keeping its by-pixel features?

  - by Eric Thoma

  (I cross-posted this from StackOverflow as this seems to be a more appropriate forum. I've looked around a little here and I did not find an answer, so I hope this is not a recurring question.) This is a question dealing with 2D world design. I am playing around by creating a 2D bird's eye view shooter game, and I am looking to make the game sleek and advanced. I hope to be able to write physics so projectiles have momentum and knock-down properties. I am immediately running into the problem of world design. I need a way to have level files that store everything there is about a game. This is easiest by just having a grid of objects. But there are thin-walls and other objects that don't seem to fit into a traditional cell of a grid. I want to be able to fit all these together so I can streamline level design; so I don't have to put in the exact pixel-specific start and end of a wall. There doesn't seem to be an obvious translation from level file to game without forcing myself into a pacman-life scenario, meaning a scenario where the game feels boxy and discrete. There is a contrast between the smoothly (relatively) moving characters and finite jumps in a grid. I would appreciate an answer that would describe implementation options or point me to resources that do. I would also appreciate references to sites that teach game design. The language I am using is Java (although I would love to use C or C++, but I can never find convenient resources in those languages). Thank you for any answers. Please leave any questions in the space below; I will be able to answer them later tonight (28th Nov).

  Read the article

• Windows FAT/NTFS Low-Level Disk Viewer (Norton DiskEdit alternative)

  - by Synetech inc.

  Hi, One of my most valuable software tools has always been Norton DiskEdit from Norton Utilities/Symantec Systemworks. I have used it for years for so many things, including, but not limited to learning file-systems. I am now in search of a similar tool that can let me view FAT and NTFS disks at a low and high level under Windows. I have seen Runtime Software’s DiskExplorer, but unfortunately, it is limited in a number of ways, particularly annoying is that it does not really let you view the disk as structured (it does not let you see directory entries from a directory that is fragmented like DiskEdit can without doing a too-exhaustive scan which doesn’t even work for FAT partitions that have cluster sizes <4KB). Does anyone know of a Windows alternative of a Norton DiskEditor? Thanks a lot.

  Read the article

• DNS server at router level vs. computer level

  - by Craig

  I've three questions. Is it better/faster/optimal to set up your server's preferred and alternate DNS servers in your OS's network settings or in your router settings? Will it cause problems if it is set up in both places, both pointing to the same IPs? I am running Windows and I have my network assign a static IP to one of my computers. This doesn't allow me to obtain the DNS server addresses from my router automatically. Is there an IP I can put in that will cause it to take the DNS server addresses from the router?

  Read the article

• Enabling hardware acceleration and Xinerama for multi-monitor/multi-GPU in Linux

  - by mynameiscoffey

  My current setup is three monitors connected as follows (monitors listed from left to right): GPU0 (nVidia GTX 280): - Dell 2405FPW (1920x1200) - Dell U2410 (1920x1200) GPU1 (nVidia 210): - Dell 2405FPW (1920x1200) Works like a charm in Windows 7, not so much in Linux. I seem to only have three real options: Run all three monitors as a seperate X screen, I get hardware acceleration but as they are all independent X sessions I cannot move windows between them and can only have firefox open on one at any given time. Run the two on GPU0 in TwinView mode and have GPU1 as a seperate X screen. Same limitation as 1 but at least two monitors work together ok. I did have an issue where occasionally Linux saw both monitors on GPU0 as a single large monitor however. Enable Xinerama and have everything work as I want it to but hardware acceleration is gone and the display is Windows 95 style choppy. My ideal solution would be to have all screens working as they do under Xinerama without the limitation of having hardware acceleration disabled. I don't even care if that means rendering all three on GPU0 and somehow farming out the display of the third monitor to GPU1, whatever works. My question is this: is there any way to accomplish this? I don't feel like my use case is so out there that there shouldn't be at least some form of support (beyond the three limited options presented above), or is my best option going to be to just suck it up and pick up a better card to replace both that can handle three outputs by itself?

  Read the article

• How to setup apache multi-site with multi-domain on ec2

  - by Esh

  Say I have two document roots domain1/ and domain2/ I know how to access those two roots from my own computer if they are hosted on the same computer. My question is that if I want to do the same thing on my ec2 server, how should I configure my elastic ips to those two roots? I know by default the elastic ip will only associate to the root with the name localhost(127.0.0.1). Anyone could give me a detailed answer? An example would help, thanks!

  Read the article

• Terminating multi-mode fiber

  - by murisonc

  I'm looking at the feasibility of terminating multi-mode fiber connections ourselves. We would be using LC connectors. I've done some research and found two different methods. One requires polishing the ends and using epoxy while the other doesn't. I like the idea of not having to polish the ends but there doesn't seem to be much information on quality or ease of use. I've found two vendors (3M and Corning) that offer kits for terminating fiber without polishing or using epoxy. Does anyone have any experience with both methods that can offer some advice? Copper is easy but fiber seems to be a whole different animal. EDIT: After looking into fusion splicing suggested in the answer I've determined it's not for us. It's my understanding that is primarily used for outside plant and is better suited for single mode fiber. It's a good answer but doesn't address the question directly. Some more information about our situation. We will only be terminating multi-mode fiber inside a building and only doing between 4 and 20 pair a year. Hiring an outside person won't work due to our location. There are currently a couple people on-site that can terminate fiber (working for another company and charging large fees) but they can only do ST and SC connectors and we only use LC. So once again does anyone have experience with terminating using both epoxy type connectors and the other type (similar to Corning Unicam)?

  Read the article

• PHP / SSH2 Multi-threading

  - by Asad Moeen

  I'm basically done using SSH2 with PHP. Some may already that while using it, the PHP code actually waits for all the listed commands to be executed in SSH and when everything is done, it then gives back the results. Where that is fine for the work I am doing, but I need some commands to be multi-threaded. $cmd= MyCommand; echo $ssh-exec($cmd); So I just want this to run in parallel 2 times. I googled some stuff but didn't get along with it. For a basic thing, I came across to this way posted by someone but it didn't work out for me. for ($i = 0; $i < 2; $i += 1) { exec("php test_1.php $i > test.txt &"); //this will execute test_1.php and will leave this process executing in the background and will go to next iteration of the loop immediately without waiting the completion of the script in the test_1.php , $i is passed as argument . } I tried to put it this way exec("echo $ssh-exec($cmd) $i test.txt &"); in the loop but either it never entered the loop or the echo $ssh-exec failed. I don't really need a very neat multi-threading. Even a single second delay would do good, thank you.

  Read the article

• How can I store all my level data in a single file instead of spread out over many files?

  - by Jon

  I am currently generating my level data, and saving to disk to ensure that any modifications done to the level are saved. I am storing "chunks" of 2048x2048 pixels into a file. Whenever the player moves over a section that doesn't have a file associated with the position, a new file is created. This works great, and is very fast. My issue, is that as you are playing the file count gets larger and larger. I'm wondering what are techniques that can be used to alleviate the file count, without taking a performance hit. I am interested in how you would store/seek/update this data in a single file instead of multiple files efficiently.

  Read the article

• Application that allows access to the other os in a multi-boot computer

  - by user23950

  Is there any application that allows access to the other os in a multi-boot computer? Access like in a virtual machine. Wherein you are able to see your other installation through it. Make file modifications, installs, and uninstalls. And those changes are being mirrored in your physical os when you boot to it?

  Read the article

• How to store a shmup level?

  - by pek

  I am developing a 2D shmup (i.e. Aero Fighters) and I was wondering what are the various ways to store a level. Assuming that enemies are defined in their own xml file, how would you define when an enemy spawns in the level? Would it be based on time? Updates? Distance? Currently I do this based on "level time" (the amount of time the level is running - pausing doesn't update the time). Here is an example (the serialization was done by XNA): <?xml version="1.0" encoding="utf-8"?> <XnaContent xmlns:level="pekalicious.xanor.XanorContentShared.content.level"> <Asset Type="level:Level"> <Enemies> <Enemy> <EnemyType>data/enemies/smallenemy</EnemyType> <SpawnTime>PT0S</SpawnTime> <NumberOfSpawns>60</NumberOfSpawns> <SpawnOffset>PT0.2S</SpawnOffset> </Enemy> <Enemy> <EnemyType>data/enemies/secondenemy</EnemyType> <SpawnTime>PT0S</SpawnTime> <NumberOfSpawns>10</NumberOfSpawns> <SpawnOffset>PT0.5S</SpawnOffset> </Enemy> <Enemy> <EnemyType>data/enemies/secondenemy</EnemyType> <SpawnTime>PT20S</SpawnTime> <NumberOfSpawns>10</NumberOfSpawns> <SpawnOffset>PT0.5S</SpawnOffset> </Enemy> <Enemy> <EnemyType>data/enemies/boss1</EnemyType> <SpawnTime>PT30S</SpawnTime> <NumberOfSpawns>1</NumberOfSpawns> <SpawnOffset>PT0S</SpawnOffset> </Enemy> </Enemies> </Asset> </XnaContent> Each Enemy element is basically a wave of specific enemy types. The type is defined in EnemyType while SpawnTime is the "level time" this wave should appear. NumberOfSpawns and SpawnOffset is the number of enemies that will show up and the time it takes between each spawn respectively. This could be a good idea or there could be better ones out there. I'm not sure. I would like to see some opinions and ideas. I have two problems with this: spawning an enemy correctly and creating a level editor. The level editor thing is an entirely different problem (which I will probably post in the future :P). As for spawning correctly, the problem lies in the fact that I have a variable update time and so I need to make sure I don't miss an enemy spawn because the spawn offset is too small, or because the update took a little more time. I kinda fixed it for the most part, but it seems to me that the problem is with how I store the level. So, any ideas? Comments? Thank you in advance.

  Read the article

• Cisco 1841: Multi-wan capable?

  - by gravyface

  Have an 1841 router with the following interfaces: 0/0 0/1 AUX on the right side, believe it's slot 1, there's an add-on interface FE0 (shows up as 000). Does this allow a multi-WAN configuration? i.e. can I use 0/1 for WAN1 and FE0 as WAN2 out-of-the-box or does this require additional licensing and/or another add-on interface in slot 0?

  Read the article

• Multi-core processors: Better performance running multiple applications?

  - by aip.cd.aish

  I realize for single applications - the application itself has to be designed to take advantage of multiple cores. But what about executing many different applications simultaneously? On my development machine at an average instance, I run multiple servers (a database server, a web server), multiple instance of IDEs (either Visual Studio or NetBeans), Web-browser with multiple tabs (in Chrome, each tab is a process on its own), FTP client, SSH client etc. Does having a multi-core system improve the ability to run multiple applications simultaneously?

  Read the article

• Did 12.04 just add multi-touch gesture support mid-release?

  - by adempewolff

  I was reviewing the updates I was about to download today and I noticed that a lot of them had to do with gesture support, noticed that many of these were new installs rather than upgrades. Has 12.04 just added multi-touch gesture support mid-release? If so, what are the capabilities that this adds? Which applications already support these capabilities and can I expect others to add support in the near future? Here are the packages that were installed: Install: libframe6:amd64 (2.2.4-0ubuntu0.12.04.1), libgeis1:amd64 (2.2.9.2-0ubuntu1), libgrail5:amd64 (3.0.6-0ubuntu0.12.04.01, automatic) And here are those that were upgraded (also including many with touch support): Upgrade: libgrip0:amd64 (0.3.4-0ubuntu2~ubuntu12.04.1, 0.3.5-0ubuntu1~12.04.1), eog:amd64 (3.4.2-0ubuntu1, 3.4.2-0ubuntu1.1), ginn:amd64 (0.2.4-0ubuntu1, 0.2.4.1-0ubuntu1) Of which the descriptions for the new installs are, libgeis1: Gesture engine interface support A common API for clients of a systemwide gesture recognition and propagation engine. libframe6: Touch Frame Library This library handles the buildup and synchronization of a set of simultaneous touches. The library is input agnostic, with bindings for mtdev, frame and XI2.1. libgrail5: Gesture Recognition And Instantiation Library This library consists of an interface and tools for handling gesture recognition and gesture instantiation. Applications can use the grail callbacks to receive gesture primitives and raw input events from the underlying kernel device. And the descriptions for the upgraded packages are, ligrip0: provides multitouch gestures to GTK+ apps Libgrip hooks gesture recognition into GTK+ applications. ginn: Gesture Injector: No-GEIS, No-Toolkits A daemon with jinn-like wish-granting capabilities: it gives applications the ability to support a subset of multi-touch gestures without having to integrate GEIS or multi-touch GTK/Qt libs. Adding in a ton of new libraries and upgrading the existing components makes me wonder if 12.04 is meant to start natively supporting gestures other than two finger scroll in the near future. I expected these capabilities to be introduced soon but I thought that they would only be rolled out in a new release, not as upgrades for an existing release. Anyone have any info about this?

  Read the article

• jqGrid - customizing the multi-select option (restrict single selection and adding custom events)

  - by Renso

  Goal: Using the jgGrid to enable a selection of a checkbox for row selection - which is easy to set in the jqGrid - but also only allowing a single row to be selectable at a time while adding events based on whether the row was selected or de-selected. Environment: jQuery 1.4.4 jqGrid 3.4.4a Issue: The jqGrid does not support the option to restrict the multi-select to only allow for a single selection. You may ask, why bother with the multi-select checkbox function if you only want to allow for the selection of a single row? Good question, as an example, you want to reserve the selection of a row to trigger another kind of event and use the checkbox multi-select to handle a different kind of event; in other words, when I select the row I want something entirely different to happen than when I select to check off the checkbox for that row. Also the setSelection method of the jqGrid is a toggle and has no support for determining whether the checkbox has already been selected or not, So it will simply act as a switch - which it is designed to do - but with no way out of the box to only check off the box (as in not to de-select) rather than act like a switch. Furthermore, the getGridParam('selrow') does not indicate if the row was selected or de-selected, which seems a bit strange and is the main reason for this blog post. Solution: How this will act: When you check off a multi-select checkbox in the gird, and then commence to select another row by checking off that row's multi-select checkbox - I'm not talking there about clicking on the row but using the grid's multi-select checkbox - it will de-select the previous selection so that you are always left with only a single selection. Furthermore, once you select or de-select a multi-select checkbox, fire off an event that will be determined by whether or not the row was selected or de-selected, not just merely clicked on. So if I de-select the row do one thing but when selecting it do another. Implementation (this of course is only a partial code snippet):             multiselect: true,             multiboxonly: true,             onSelectRow: function (rowId) {                 var gridSelRow = $(item).getGridParam('selrow');                 var s;                 s = $(item).getGridParam('selarrrow');                 if (!s || !s[0]) {                     $(item).resetSelection();                     $('#productLineDetails').fadeOut();                     lastsel = null;                     return;                 }                 var selected = $.inArray(rowId, s) != -1;                 if (selected) {                     $('#productLineDetails').show();                 }                 else {                     $('#productLineDetails').fadeOut();                 }                 if (rowId && rowId !== lastsel && selected) {                     $(item).GridToForm(gridSelRow, '#productLineDetails');                     if (lastsel) $(item).setSelection(lastsel, false);                 }                 lastsel = rowId;             }, In the example code above: The "item" property is the id of the jqGrid. The following to settings ensure that the jqGrid will add the new column to select rows with a checkbox and also the not allow for the selection by clicking on the row but to force the user to have to click on the multi-select checkbox to select the row: multiselect: true, multiboxonly: true, Unfortunately the var gridSelRow = $(item).getGridParam('selrow') function will only return the row the user clicked on or rather that the row's checkbox was clicked on and NOT whether or not it was selected nor de-selected, but it retrieves the row id, which is what we will need. The following piece get's all rows that have been selected so far, as in have a checked off multi-select checkbox: var s; s = $(item).getGridParam('selarrrow'); Now determine if the checkbox the user just clicked on was selected or de-selected: var selected = $.inArray(rowId, s) != -1; If it was selected then show a container "#productLineDetails", if not hide that container away. The following instruction populates a form with the grid data using the built-in GridToForm method (just mentioned here as an example) ONLY if the row has been selected and NOT de-selected but more importantly to de-select any other multi-select checkbox that may have been selected: if (rowId && rowId !== lastsel && selected) {                     $(item).GridToForm(gridSelRow, '#productLineDetails');                     if (lastsel) $(item).setSelection(lastsel, false); }

  Read the article

• Finding out which higher level function is making lots of low level calls

  - by ming yeow

  Hi folks, I have a function that is being called more than a thousand times, slowing everything down. However, it is a low level function, and do not know which of my high level function is lopping and making these calls. How can i find out?

  Read the article

• how to multi-boot/upgrade linux from LVM-based partition

  - by kenny-bobby

  i currently have FC3 linux which installed itself on the hard disk using LVM partitioning, so it is basically all one big partition. i would like to try some other distributions and upgrade to something newer, but don't want to lose my current capabilities and data files, and i know nothing or less about LVM. Is it possible (and if so an example would be nice) to install a non-LVM-based distribution on the LVM disk and have multi-boot options? Or do i have to start over new and drop the LVM? My guess is that i should save my /home (data files and .rc files) on a backup device first, then somewhere/somehow create a new partion for installing another distribution. Any LVM experts out there that have tried anything like this--well i sure could use some pointers and advice...

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >