Search Results

Search found 4690 results on 188 pages for 'ran'.

Page 3/188 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Used HDD/ran DiskSmartView/40,000 Power-on-hours?? should i trust it w/ my data, or take it back and bitch?

  - by David Lindsay

  I just bought a used hard drive from a University Surplus Store. Decided to run DiskSmartView to make sure it wasn't ready to fail. 40,000 power-on-hours I don't know if I feel like trusting my data to something that used. I really dont know if thats unreasonably old, but when i compare it to the POH reading i get when testing my other hdds its more than 3x older (my others have 2110 hours, 6150 hours, etc.. It's a Western Digital, so that gives me a little bit of hope(WDC WD4000KD-00NAB0). I could sure use someone else's opinion here. Thanks, DAVE

  Read the article

• Stuck due to "knowing too much"

  - by Ran Biron

  Note more discussion at http://news.ycombinator.com/item?id=4037794 Welcome Hacker News Visitors! While HN is a fine forum for discussion and debate, Programmers - Stack Exchange is not. From the FAQ: If your motivation for asking the question is “I would like to participate in a discussion about ____”, then you should not be asking here. However, if your motivation is “I would like others to explain ____ to me”, then you are probably OK. (Discussions are of course welcome in our real time web chat.) Currently, this question is viewed by the membership of Programmers.SE as more likely to provoke unproductive discussion than constructive answers; while debates on its form and future are conducted, it will be locked to prevent arguments and vandalism. -- Shog9 I have a relatively simple development task, but every time I try to attack it, I end up spiraling in deep thoughts - how could it extending the future, what are the 2nd generation clients going to need, how does it affect "non functional" aspects (e.g. Performance, authorization...), how would it best be architectured to allow change... I remember myself a while ago, younger and, perhaps, more eager. The "me" I was then wouldn't have given a thought about all that - he would've gone ahead and wrote something, then rewrote it, then rewrote it again (and again...). The "me" today is more hesitant, more careful. I find it much easier today to sit and plan and instruct other people on how to do things than to actually go ahead and do them myself - not because I don't like to code - the opposite, I love to! - but because every time I sit at the keyboard, I end up in that same annoying place. Is this wrong? Is this a natural evolution, or did I drive myself into a rut? Fair disclosure - in the past I was a developer, today my job title is a "system architect". Good luck figuring what it means - but that's the title. Wow. I honestly didn't expect this question to generate that many responses. I'll try to sum it up. Reasons: Analysis paralysis / Over engineering / gold plating / (any other "too much thinking up-front can hurt you"). Too much experience for the given task. Not focusing on what's important. Not enough experience (and realizing that). Solutions (not matched to reasons): Testing first. Start coding (+ for fun) One to throw away (+ one API to throw away). Set time constraints. Strip away the fluff, stay with the stuff. Make flexible code (kinda opposite to "one to throw away", no?). Thanks to everyone - I think the major benefit here was to realize that I'm not alone in this experience. I have, actually, already started coding and some of the too-big things have fallen off, naturally. Since this question is closed, I'll accept the answer with most votes as of today. When/if it changes - I'll try to follow.

  Read the article

• How often is your "Go-To" language the same as your favorite??

  - by K-RAN

  I know that there's already a question asking for your favorite programming language here. I'm curious though, what's your go-to language? The two can be very different. For example, I love Haskell. I learned it this past semester and I fell in love with it's very concise solutions and awesome syntax (I love theoretical math so something like fib = 1 : 1 : [ f | f <- zipWith (+) fibSeq (tail fibSeq)] makes my inner mathematician and computer scientist jump with joy!). However, the majority of my projects for classes and jobs have been in C/C++ & Java. As a result, most of the time when I'm testing something like an algorithm or Data Structure I go straight to C++. What about you guys? What languages do you love and why? What about your go-to language? What language do you use most often to get things done for work or personal projects and why? How often does a language fall into both categories??

  Read the article

• keeping track of multiple runs of the same function, part 2

  - by qwertymk

  This is related to this Anyway what I need is actually something slightly different I need some way of doing this: function run(arg) { this.ran = this.ran || false; if (!this.ran) init; /* code */ this.ran = true; } This works fine, I just want to make sure that this code works even when this in case it was called with call() or apply() Check this out for what I'm talking about, All of the calls after the first one should all be true, no matter the context

  Read the article

• Java simple encryption

  - by Ran

  Hello, I would like to encrypt a textual (configuration) file stored on disk. Trying to use DES encryption I've had fatal error on client machines, I later found out caused because the algorithm could not handle accented characters (!) I suspect that was because I was using old packages (sun.misc.BASE64Decoder) - but I'm not sure that is the reason. However, I'm looking for a simpler solution - I need a really simple encryption (I know some people would not agree on that) - not RSA of 128 bit keys or so, just obscuring the text from curious eyes. It is really weird that I could not find on the web a simple trivial solution. Any idea, anyone ? Thanks, Ran

  Read the article

• IntelliJ IDEA plugin development: Get classes VirtualFile (or paths) for a specific source VirtualFi

  - by Ran Biron

  Hi all. This is a cross-post from http://www.jetbrains.net/devnet/message/5264436#5264436 - I failed to get any answer on that forum for two weeks now, so I'm re-asking it here (please don't flame). This question refers to plugin development for the IntelliJ IDEA IDE, specifically targeting java development: Is there any API to get the list of .class files for given source file? I'm trying to write a plugin that creates a binary patch jar based on a changelist. I've managed to get the changelist and, from it, a list of source files (VirtualFile). Now I'm trying to get the compiled class files for these source files (I don't mind preforming a "make" or relying on the previous compile output). I've played a bit with ProjectFileIndex but could only find the classes root. I'd hate to do a "dumb" path-based search because inner classes (and inner anonymous classes) would make it difficult to get correctly. Is there such an API? Or am I doomed to parse the paths? Thanks, Ran.

  Read the article

• How do I switch java versions to an earlier version in Fedora 17?

  - by JHutson456

  I just installed Fedora 17. I'm setting up the Android Build Environment and need Java. I downloaded and installed jdk-6u32-linux-amd64.rpm I ran java -version and it spit out the correct version. Well a day or two later i tried my first compile in Fedora 17 and it complained about java and failed. I ran java -version again and low and behold it spits out $ java -version java version "1.7.0_03-icedtea" OpenJDK Runtime Environment (fedora-2.1.fc17.7-x86_64) OpenJDK 64-Bit Server VM (build 22.0-b10, mixed mode) I'm stumped. I mean, i've run the update/upgrade commands since i installed but i didn't think that updated full version revisions... So, I ran alternatives --config java and that only gave me the java 1.7 version. While digging around more I discovered that the recommended version of Java for the build environment is jdk-6u27-linux-x64-rpm.bin so I downloaded that from here: Oracle Download When I ran: sudo sh jdk-6u27-linux-x64-rpm.bin it returned: Unpacking... Checksumming... Extracting... UnZipSFX 5.50 of 17 February 2002, by Info-ZIP ([email protected]). inflating: jdk-6u27-linux-amd64.rpm inflating: sun-javadb-common-10.6.2-1.1.i386.rpm inflating: sun-javadb-core-10.6.2-1.1.i386.rpm inflating: sun-javadb-client-10.6.2-1.1.i386.rpm inflating: sun-javadb-demo-10.6.2-1.1.i386.rpm inflating: sun-javadb-docs-10.6.2-1.1.i386.rpm inflating: sun-javadb-javadoc-10.6.2-1.1.i386.rpm Preparing... ########################################### [100%] package jdk-2000:1.6.0_32-fcs.x86_64 (which is newer than jdk-2000:1.6.0_27-fcs.x86_64) is already installed Done. so now I'm confused. I ran: alternatives --config java again but it's still only returning 1.7 so I don't know what to do.I want to end up with 6u27 as the installed and functional version of the JDK. Thank you.

  Read the article

• Random BSODs on Win7 boot. Can't find a valid reason.

  - by 0plus1

  Hi, I bought and assembled a new pc: ASUS m4a785td-v EVO AMD x4 620 OCZ Black Edition 2x 2gb WD 500gb sata Win7 Ultimate 64bit fresh install BSOD on boot. Formatted, reinstalled, BSOD on install. Ran memtest - no errors. Ran Win7 install in safe mode. Installed, random BSOD on win7 startup, even in safe mode. Updated BIOS. Ran the win7 memtest (no error), booted after some tries and ran Prime95 blend test for 12 hours straight with no errors at all! When the pc has booted, win7 runs as smooth as possible, I've been playing STALKER for 4 hours straight with not a single hiccup. Using Blue Screen View I can see that every BSOD involves: ntoskrnl.exe Here are the dumps Any help would be greatly appreciated, this thing is driving me crazy.

  Read the article

• gcServer config not taking effect

  - by G33kKahuna

  I'm supporting a ASP.NET v2.0 app installed on a Windows 2003 SP3 Enterprise on a quad core 8G machine running on .NET 2.0 SP1. 1.before enabling the config, ran "tasklist /m mscorwks.dll" Image Name PID Modules w3wp.exe 7888 mscorwks.dll 2.add under section in web.config 3.ran IISRESET, rebooted server too 4.ran "tasklist /m mscorsvr.dll" INFO: No tasks are running which match the specified criteria. 5.ran "tasklist /m mscorwks.dll" Image Name PID Modules w3wp.exe 6251 mscorwks.dll It seems like gcServer is not taking effect. Are there any additional settings/ configurations necessary to get it working?

  Read the article

• Java web app deployment and ControlTier adoption

  - by Ran

  I've been searching for a configuration and deployment manager tool for my java-linux based web service and have been looking mainly at ControlTier (http://controltier.org). We operate at a medium scale (100's of hosts, multi-DC, dozens of services). There seem to be be plenty of lower level system admin tools such as chef, puppet, cfengine, bcfg2 and more and my understanding and the reason I'm calling them "low level" is that they are great for system level administration tasks such as setting up a mount, file permissions, users etc but aren't designed, for example for java deployments, which usually come with a build process and special java semantics. In many cases any tool can be used to do anything but if it was not designed for the task it can get uncomfortable. OTOH control-tier seem to have been designed just for that - java application deployments, at least that's what all the tutorials on their site demonstrate but here's the problem - The wiki at http://controltier.org/wiki/ is pretty good and stuffed with examples and the company behind the open source CT product is very responsive (pushy...) however, I'm yet to have seen any material from 3rd party users on the net. No success stories, no detailed blog posts, no best practices, no cheat sheets, not even hate letters, nothing. This plays badly for DTO solutions, CT's sponsor for two reasons, one is that it makes me suspicious what's the reason for the poor adoption? and second, what do I do if I get stuck and there's no help page on CT's wiki page and the mailing list is too slow to answer. I'm stuck with a "free" product that a consultancy company is pushing. So my question here - I'd be interested in hearing if anyone has had real world experience with CT for java based web app deployments and if he'd thumb up the product? Any other comments that may enlighten me are welcome of course...

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• Need help ttoubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after rstarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What i have done: I thought it was HDD at first, since this is the only part of the coputer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from bootable USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD apears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoughrouly. The problem still persists, what should my next steps be? Thanks in advance.

  Read the article

• Deployment and monitoring tools for java/tomcat/linux environment

  - by Ran

  I'm a developer for many years, but don't have tons of experience in ops, so apology if this is a newbe question. In my company we run a web service written in Java mainly based on a Tomcat web server. We have two datacenters with about 10 hosts each. Hosts are of several types: Dababase, Tomcats, some offline java processes, memcached servers. All hosts are Linux CentOS Up until now, when releasing a new version to production we've been using a set of inhouse shell script that copy jars/wars and restart the tomcats. The company has gotten bigger so it has become more and more difficult operating all this and taking code from development, through QA, staging and to production. A typical release many times involves human errors that cost us precious uptime. Sometimes we need to revert to last known good and this isn't easy to say the least... We're looking for a tool, a framework, a solution that would provide the following: Supports the given list of technology (java, tomcat, linux etc) Provides easy deployment through different stages, including QA and production Provides configuration management. E.g. setting server properties (what's the connection URL of each host etc), server.xml or context configuration etc Monitoring. If we can get monitoring in the same package, that'll be nice. If not, then yet another tool we can use to monitor our servers. Preferably, open source with tons of documentation ;) Can anyone share their experience? Suggest a few tools? Thanks!

  Read the article

• How to set up apache with parallel plesk?

  - by Ran Gualberto

  I'm working with the Windows Server 2008 (a godaddy Windows dedicated server). My problem is that .htaccess is not working in the server. And I just figured out that apache is not installed. I would like to know how to run the apache with the plesk (with existing php setup). And how to run the apache with the current site directory C:\inetpub\vhosts. My goal is to make .htaccess work on the server with plesk and with the directory C:\inetpub\vhosts.

  Read the article

• Masquerade traffic from certain source IP to VPN connection

  - by Shuo Ran

  Network Setup: 10.0.0.1 Router: to internet 10.0.0.70 Server: Ubuntu based server,default gateway is 10.0.0.1 10.0.0.51 PC I created a PPTP connection(interface: ppp0) on Server to a machine on the internet, what I want to do is route all the traffic from certain IP address(10.0.0.51) through the PPTP connection and then to the internet. What I did are: Set the gateway on PC(10.0.0.51) as 10.0.0.70 Enabled ipv4 forward on 10,0,0,70 Add the masquerade rule to iptable: iptables -t nat -A POSTROUTING -o ppp0 -s 10.0.0.51 -j MASQUERADE After that, it seems none of the traffic from 10.0.0.51 be redirected to ppp0, instead these traffic are still going through 10.0.0.1 directly. Any thoughts on it?

  Read the article

• Apt-get saying "Unable to correct problems, you have held broken packages."

  - by YatharthROCK

  TL;DR: sudo apt-get install ... saying "Unable to correct problems, you have held broken packages." The problem I was trying to get the WebApps feature for PP and QQ following this blog post. I ran the sudo add-apt-repository ppa:webapps/preview command to add the repository, but i got a connection error. Since I know my current ISP gives a shaky connection, I tried again and sure enough, it worked. Then I ran sudo apt-get install unity-webapps-preview, but I realized we had to update apt-get first, so I hit Ctrl + C to stop it. Then I ran sudo apt-get update which worked w/o a fuss, but when I ran sudo apt-get install unity-webapps-preview again later, it showed an error message. Here's the dump: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: unity-webapps-preview : Depends: xul-ext-unity but it is not going to be installed Depends: xul-ext-websites-integration but it is not going to be installed Depends: xul-ext-webaccounts but it is not going to be installed E: Unable to correct problems, you have held broken packages. I think this might be because of me interrupting the earlier command. It hadn't got a chance to output anything, though — I stopped it pretty fast. What I tried I have tried running a number of commands:- sudo apt-get install --fix-broken sudo apt-get autoclean sudo apt-get autoremove sudo apt-get -f install sudoapt-get install ppa-purgeandsudo ppa-purge ppa:webapps/preview` Even after running sudo apt-get upgrade after every try, none of them worked. Research I tried searching Google, looking at a couple of forums and searching on AU, but to no avail. Help would be appreciated.

  Read the article

• OpenCV install problems on Studio 12.04 - broken dependencies

  - by Will

  I'm trying to follow the Ubuntu OpenCV documentation at OpenCV. The provided script has a line which executed for some time, taking away more packages than I expected (such as ubuntu-studio video); sudo apt-get -qq remove ffmpeg x264 libx264-dev When the script gets to the line below, it bombs; sudo apt-get -qq install libopencv-dev build-essential checkinstall cmake pkg-config yasm libtiff4-dev libjpeg-dev libjasper-dev libavcodec-dev libavformat-dev libswscale-dev libdc1394-22-dev libxine-dev libgstreamer0.10-dev libgstreamer-plugins-base0.10-dev libv4l-dev python-dev python-numpy libtbb-dev libqt4-dev libgtk2.0-dev libfaac-dev libmp3lame-dev libopencore-amrnb-dev libopencore-amrwb-dev libtheora-dev libvorbis-dev libxvidcore-dev x264 v4l-utils ffmpeg The error msg is; E: Unable to correct problems, you have held broken packages. I've since run Update-Manager, run sudo apt-get updates, rebooted, tried the above script line manually, and still no change. I've just run sudo apt-get install -f and nothing seemed to change. It did mention that some packages were no longer needed and could be removed by apt-get autoremove, so I ran that. It removed a number of packages, so I reran the install command above. Still same problem of held broken packages. I just ran sudo apt-get -u dist-upgrade Part of the response was; The following packages have been kept back: gstreamer0.10-ffmpeg I'm not sure what that means. I do know that it shows up in my Update-Manager and cannot be checked I then ran sudo dpkg --configure -a and then reran sudo apt-get -f install and the package was still not upgraded, though there was this very interesting comment; Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: gstreamer0.10-ffmpeg : Depends: libavcodec53 (< 5:0) but it is not going to be installed or libavcodec-extra-53 (< 5:0) but 5:0.7.2-1ubuntu1+codecs1~oneiric2 is to be installed E: Unable to correct problems, you have held broken packages. Then I ran sudo apt-get -u dist-upgrade It showed I had one held package, so I ran; sudo apt-get -o Debug::pkgProblemResolver=yes dist-upgrade It also exited without upgrading the package, so I ran; sudo apt-get remove --dry-run gstreamer0.10-ffmpeg:i386 And it gave me; *The following packages will be REMOVED: arista gstreamer0.10-ffmpeg 0 upgraded, 0 newly installed, 2 to remove and 0 not upgraded. Remv arista [0.9.7-3ubuntu1] Remv gstreamer0.10-ffmpeg [0.10.12-1ubuntu1]* But when I reran sudo apt-get -u dist-upgrade It showed the package was still there. *The following packages have been kept back: gstreamer0.10-ffmpeg 0 upgraded, 0 newly installed, 0 to remove and 1 not upgraded.* Update: Just went into Synaptic PM and completely removed gstreamer0.10-ffmpeg Reran sudo apt-get -u dist-upgrade And was told; 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. However, when I ran the original apt-get to install opencv (first code at the top of this question), it still gave me the same broken package errors. So I tried $ cat /etc/apt/sources.list # # deb cdrom:[Ubuntu-Studio 11.10 _Oneiric Ocelot_ - Release i386 (20111011.1)]/ oneiric main multiverse restricted universe # deb cdrom:[Ubuntu-Studio 11.10 _Oneiric Ocelot_ - Release i386 (20111011.1)]/ oneiric main multiverse restricted universe # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. deb http://us.archive.ubuntu.com/ubuntu/ precise main restricted deb-src http://us.archive.ubuntu.com/ubuntu/ precise main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb http://us.archive.ubuntu.com/ubuntu/ precise-updates main restricted deb-src http://us.archive.ubuntu.com/ubuntu/ precise-updates main restricted ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team. Also, please note that software in universe WILL NOT receive any ## review or updates from the Ubuntu security team. deb http://us.archive.ubuntu.com/ubuntu/ precise universe deb-src http://us.archive.ubuntu.com/ubuntu/ precise universe deb http://us.archive.ubuntu.com/ubuntu/ precise-updates universe deb-src http://us.archive.ubuntu.com/ubuntu/ precise-updates universe ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team, and may not be under a free licence. Please satisfy yourself as to ## your rights to use the software. Also, please note that software in ## multiverse WILL NOT receive any review or updates from the Ubuntu ## security team. deb http://us.archive.ubuntu.com/ubuntu/ precise multiverse deb-src http://us.archive.ubuntu.com/ubuntu/ precise multiverse deb http://us.archive.ubuntu.com/ubuntu/ precise-updates multiverse deb-src http://us.archive.ubuntu.com/ubuntu/ precise-updates multiverse ## N.B. software from this repository may not have been tested as ## extensively as that contained in the main release, although it includes ## newer versions of some applications which may provide useful features. ## Also, please note that software in backports WILL NOT receive any review ## or updates from the Ubuntu security team. deb http://security.ubuntu.com/ubuntu precise-security main restricted deb-src http://security.ubuntu.com/ubuntu precise-security main restricted deb http://security.ubuntu.com/ubuntu precise-security universe deb-src http://security.ubuntu.com/ubuntu precise-security universe deb http://security.ubuntu.com/ubuntu precise-security multiverse deb-src http://security.ubuntu.com/ubuntu precise-security multiverse ## Uncomment the following two lines to add software from Canonical's ## 'partner' repository. ## This software is not part of Ubuntu, but is offered by Canonical and the ## respective vendors as a service to Ubuntu users. deb http://archive.canonical.com/ubuntu precise partner # deb-src http://archive.canonical.com/ubuntu oneiric partner ## Uncomment the following two lines to add software from Ubuntu's ## 'extras' repository. ## This software is not part of Ubuntu, but is offered by third-party ## developers who want to ship their latest software. # deb http://extras.ubuntu.com/ubuntu oneiric main # deb-src http://extras.ubuntu.com/ubuntu oneiric main # deb http://download.opensuse.org/repositories/home:/popinet/xUbuntu_11.04 ./ # disabled on upgrade to precise and then; $ cat /etc/apt/sources.list.d/* But I don't have enough reputation to post the results here (it says I need at least 10 reputation points to post more than 2 links), so I don't know how to provide the requested feedback. Then tried; $ sudo apt-get check [sudo] password for <abcd>: Reading package lists... Done Building dependency tree Reading state information... Done However, no resolution of the problem yet. What else do I need to do? Will an upgrade to Ubuntu Studio 13.xx solve this problem (or compound it)?

  Read the article

• Can't install Spotify Linux preview

  - by Wut

  I'm having trouble installing the Spotify Linux preview. I'm kinda new to Ubuntu so I'm not sure if I did something wrong. First, in the terminal, I ran this: sudo gedit /etc/apt/sources.list At the bottom, I added this: deb http://repository.spotify.com stable non-free # deb-src http://repository.spotify.com stable non-free Then I ran this: sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 4E9CFF4E Next: sudo apt-get update It seemed to have gone well, as there were no error messages. So next, I ran this: sudo apt-get install spotify-client-qt But when I did, I got this: You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: spotify-client-qt : Depends: spotify-client but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). Any ideas?

  Read the article

• Remove kubuntu-desktop from ubuntu 12.04 [closed]

  - by Meijuh

  Possible Duplicate: How to completely remove desktop? So, I thought I managed to remove KDE completely, but apparently that did not work at all, because every KDE application is back, including the KDE splash screen. I ran sudo apt-get autoremove --purge kubuntu-desktop Then I ran sudo apt-get install --reinstall ubuntu-desktop Then I ran sudo sudo update-alternatives --config default.plymouth Then I rebooted and everything seemed to be the original ubuntu-desktop (without the kde splash screen and other KDE applications). But now, one week later I still boot to ubuntu-desktop, but like I said, the kde splash screen and applications are all back. How should I remove kubuntu-desktop?

  Read the article

• Why do I get a 403 error when accessing my apache server?

  - by nishan

  Im running Ubuntu 12.04 LTS on a system with 2 GB RAM and a 500 GB HDD. My hard drive has 4 partitions: Partition 1 = 40 gb Windows (NTFS, lable = win32) Partition 2 = 320 gb Windows (FAT label = common) Partition 3 = 40 gb Ubuntu (EXT4) I installed apached2. Then, to change its default www directory, I ran gksu gedit /etc/apache2/sites-enabled/000-default and, in the editor, changed the location to /media/common/www. After that I ran these commands in a terminal: chmod 777 /media/common/www chmod 777 /media/common/www/*.* After that I ran: firefox 127.0.0.1/index.php It said: Forbidden You don't have permission to access / on this server. Apache/2.2.22 (Ubuntu) Server at 127.0.0.1 Port 80 Before my changes it was working fine. How can I run my websites?

  Read the article

• Db2 error : SQL0901N, SQLSTATE=58004

  - by Harv

  Hi, Can i use Atomic in the parrent procedure as well as in the procedure which the mail procedure calls. My procedure compiles perfectly, but sometimes when I execute it. I receive following error: DB2 Database Error: ERROR [58004] [IBM][DB2/NT64] SQL0901N The SQL statement failed because of a non-severe system error. Subsequent SQL statements can be processed. (Reason "Sdir len bad: 1542!=1520+14".) SQLSTATE=58004 However, surprisingly when i commented the "ATOMIC" keyword in the main procedure and ran again it ran perfectly. But when I ran it again after uncommenting it still did not give any errors and ran perfectly. So the error that I recieve is not something that I recive everytime.Could some one please let me know what could be the issue and what needs to be done to resolve this. As on goolgeing I did not find any leads on this. Thanks, Harveer

  Read the article

• Identify in a unit test if Jetbrains IntelliJ IDEA 8 or 9 is running

  - by Ran Biron

  I need to know, in a context of a unit test, if Jetbrains IntelliJ idea is the test initiator and if it is, which version is running (or at least if it's "9" or earlier). I don't mind doing dirty tricks (reflection, filesystem, environment...) but I do need this to work "out-of-the-box" (without each developer having to setup something special). I've tried some reflection but couldn't find a unique identifier I could latch onto. Any idea? Oh - the language is Java.

  Read the article

• PDF thumbnails in TeXShop (LaTeX)

  - by joec

  How can i create PDF thumbnails in TeXShop using LaTeX and thumbpdf? I have \usepackage{thumbpdf} in my preamble, ran LaTeX twice, ran $ thumbpdf report.pdf from a Terminal (I'm on a Mac), then ran LaTeX again, but the PDF has no thumbnails? Am I missing a step? The thumbpdf command created png files but then deleted them again, and wrote a file called report.tpt. Thanks.

  Read the article

• Sentiment analysis for twitter in python

  - by Ran

  I'm looking for an open source implementation, preferably in python, of Textual Sentiment Analysis (http://en.wikipedia.org/wiki/Sentiment_analysis). Is anyone familiar with such open source implementation I can use? I'm writing an application that searches twitter for some search term, say "youtube", and counts "happy" tweets vs. "sad" tweets. I'm using Google's appengine, so it's in python. I'd like to be able to classify the returned search results from twitter and I'd like to do that in python. I haven't been able to find such sentiment analyzer so far, specifically not in python. Are you familiar with such open source implementation I can use? Preferably this is already in python, but if not, hopefully I can translate it to python. Note, the texts I'm analyzing are VERY short, they are tweets. So ideally, this classifier is optimized for such short texts. BTW, twitter does support the ":)" and ":(" operators in search, which aim to do just this, but unfortunately, the classification provided by them isn't that great, so I figured I might give this a try myself. Thanks! BTW, an early demo is here and the code I have so far is here and I'd love to opensource it with any interested developer.

  Read the article

• gcServer config not taking effect

  - by G33kKahuna

  I'm supporting a ASP.NET v2.0 app installed on a Windows 2003 SP3 Enterprise on a quad core 8G machine running on .NET 2.0 SP1. before enabling the config, ran "tasklist /m mscorwks.dll" Image Name PID Modules w3wp.exe 7888 mscorwks.dll add under section in web.config ran IISRESET, rebooted server too ran "tasklist /m mscorsvr.dll" INFO: No tasks are running which match the specified criteria. ran "tasklist /m mscorwks.dll" Image Name PID Modules w3wp.exe 6251 mscorwks.dll It seems like gcServer is not taking effect. Are there any additional settings/ configurations necessary to get it working?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >