Search Results

Search found 14588 results on 584 pages for 'usb drive'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 3/584 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • USB 3.0 hard disk not detected on a particular host controller?

    - by Alvin Wong
    I have a USB 3.0 hard disk which has always been working on my desktop with an XHCI. Now I just bought a notebook with an XHCI (something with Intel's Ivy Bridge setup). The first time I plug the hard disk in its 3.0 port it is detected and working. A few hours later I try to connect it again, but seems that the notebook just ignored it! The light on the hard disk didn't blink as usual (instead it is hold at on). I then tested it with my desktop again and it is working perfectly. It gets trickier when I plug it in the USB 2.0 port of that notebook it is detected and working perfectly (despite the slower speed). Then I try to plug in an USB 2.0 USB flash drive to that USB 3.0 port, and it is detected (of course as USB 2.0). So, there are two USB 3.0 ports on my notebook's XHCI. Both of them are not working with my hard disk but working perfectly fine with my USB 2.0 UFD. What's wrong with it? When I plug in the hard disk, device manager doesn't change. I've tried re-installing the driver for the XHCI, but it changes nothing. Had I broke the USB 3.0-specific pins of both USB 3.0 ports?

    Read the article

  • USB drives not recognized all of a sudden (usb_storage not loaded lsmod does not report usb_storage)

    - by Siddharth
    I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

    Read the article

  • Can't access USB drive anymore

    - by marie
    I have a 32 GB Lacie Cookey USB flash disk that doesn't show in the Computer window but it's visible as a device. cmd > diskpart DISKPART> list disk Disk ### Status Size -------- ------------- ------ Disk 0 Online 149 G Disk 1 No Media 0 DISKPART> select disk 1 Disk 1 is now the selected disk. DISKPART> clean Virtual Disk Service error: There is no media in the device. It also appears in the Disk Management tool, but the box is empty. Is there anything I can do or is it dead? ............................................................ output from ChipGenius: Description: [F:]USB Mass Storage Device(LaCie CooKey) Device Type: Mass Storage Device Protocal Version: USB 2.00 Current Speed: High Speed Max Current: 200mA USB Device ID: VID = 059F PID = 103B Serial Number: 070535924B170C18 Device Vendor: LaCie Device Name: CooKey Device Revision: 0100 Manufacturer: LaCie Product Model: CooKey Product Revision: PMAP Controller Vendor: Phison Controller Part-Number: PS2251-67(PS2267) - F/W 06.08.53 [2012-09-26] Flash ID code: 983AA892 - Toshiba [TLC] Tools on web: http://dl.mydigit.net/special/up/phison.html

    Read the article

  • USB-to-Parallel adapter rated as USB 1.1 - will its driver lower speed of USB 2.0 bus?

    - by cumminjm
    I need to connect a printer with a parallel port to a computer with only a USB 2.0 bus. I'd like to do so without lowering the USB 2.0 bus speed to USB 1.1. All the USB-to-Parallel adapter cable found so far seem to be rated as USB 1.1 and they come with a CD which presumably contains a necessary driver. I haven't purchased one and tested it out yet, but if so, would the cable's driver lower speed of USB 2.0 bus?

    Read the article

  • USB Hub vs. Dockinstation USB vs. Laptop USB

    - by Will
    I recently had thougts about my current setup in my office, especially about the UBS ports distribution. Here's my setup: I have a Lenovo T410 docked to a Lenovo Dockingstation Series 3, that providey me with 6 USB ports, which I use all (3 ext. drives, mouse, keyboard, USB Hub of monitor). The USB hub on my ext. monitor (most probably powered by the ext. monitor's power supply) provides me with 2 USB ports, where I use one for my webcam and another for USB sticks. On my T410 itself I have 4 USB slots, that are usually not used, as don't want to mess with USB plugs when undocking my laptop, now and then I plug my printer on one of these, just because I don't have any UBS ports left. Now I'm wondering how fast each of these slots are: I assume that all the 6 USB ports from the dockinstation somehow go through the docking connector on the bottom of my laptop. Does this connector has such a big bandwidth for all these 6 USB ports to perform like if they were dedicated ports as the 4 ones on my laptop? Also how is generally the performance of USB hubs (like the one on my ext. monitor?)?

    Read the article

  • Save to Hard Drive instead of bootable USB

    - by WAM
    I followed the instructions on the Ubuntu website on how to put Ubuntu 12.04 on a USB and make it a bootable USB stick for windows. It worked fine and I can boot up and run Ubuntu, but every time I try to download software or change settings it tries to save it to the USB rather than the hard drive built into the computer. The USB doesn't have enough space so the download fails and in addition it doesn't retain setting changes so when I restart my computer all the settings return to default and anything I saved is gone. Is there any way to change things so that when I download software or change settings Ubuntu will save it to my hard drive instead of the USB?

    Read the article

  • external hard drive not detected after ubuntu crash [restarting machine]

    - by Netmoon
    today i tried to watch movie [with vlc media player] from my external hard drive [expansion portable 500 GB], and it's play good, then pause the movie and play it again, and my Ubuntu crashed! [Ubuntu 12.04]i had to restart the machine, so did it, but after that Ubuntu can't recognize this hard drive! i changed USB cable but it was not effective. this is my dmesg command result : [ 191.281630] usb 2-1.3: new full-speed USB device number 9 using ehci_hcd [ 191.353527] usb 2-1.3: device descriptor read/64, error -32 [ 191.529115] usb 2-1.3: device descriptor read/64, error -32 [ 191.704669] usb 2-1.3: new full-speed USB device number 10 using ehci_hcd [ 191.776524] usb 2-1.3: device descriptor read/64, error -32 [ 191.952202] usb 2-1.3: device descriptor read/64, error -32 [ 192.127772] usb 2-1.3: new full-speed USB device number 11 using ehci_hcd [ 192.534742] usb 2-1.3: device not accepting address 11, error -32 [ 192.606749] usb 2-1.3: new full-speed USB device number 12 using ehci_hcd [ 193.013696] usb 2-1.3: device not accepting address 12, error -32 [ 193.013906] hub 2-1:1.0: unable to enumerate USB device on port 3 note: I am able to hear the sound of the external drive lens. When attach hard drive to usb port, the status light goes on, but it's low bright and i think its power is low! try to mount in Microsoft Windows 7, but nothing happened.

    Read the article

  • Unable to recognize hard drive after replacing a drive

    - by Peter Schriver
    I have a Poweredge 830 that I had been using with 1 OS Sata drive and 3 data drives. One of the drives had some failing sectors so I replaced it with a different drive. For some bizarre reason the computer would not reboot so I disconnected all of the media drives and did a clean reinstall on the OS drive. Only the boot drive and one of the media drives are now recognized by my Bios. Drive 0 and 2. Drive 1 and 3 are listed in the Bios as "Unkown Device" Any help would be appreciated I think there may be something wrong with the install. For some reason when I attempt to change the display it says I have a laptop.If you think a reinstall is in order I will try that.

    Read the article

  • linux: mount old ATA disk to USB adapter

    - by 130490868091234
    I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

    Read the article

  • Backup folder on sometimes attached external usb harddrive

    - by ctrler
    My girlfriend no longer has space her laptops drive to store her photos. The drive she has now is 750GB, so to go to a bigger drive would be expensive, as there isn't many 1.5tb 2.5 inch 9.5mm hdd on the market (as of now, there is only one). Because of that, I am thinking of moving her pictures to a cheap external usb hdd. As of now, I'm automatically backing up her important folders (My Documents, Pictures, etc.) using Windows 7 default backup software to a network drive. My problem is that I don't know of a good solution to automatically backup a folder residing on an usb disk. The usb disk won't be attached to the computer all the time, so I can't just treat it as a normal backup folder. Sometimes the backup would run and the folder would not be there! Anyone knows any software or methodology to backup folders on external usb hard drives that are not always present? Thanks

    Read the article

  • usb ntfs pen drive and hard drive not working after connection to ubuntu

    - by lemon619
    as said in the title first of all i connected a usb key (ntfs formatted) with data in it, on ubuntu 12.04, after i disconnected it i was no more able to access the usb key neither from windows nor from ubuntu 12.04. The system asks me to format my usb key Just now i connected a hard drive ntfs formatted with data in it to ubuntu 12.04. I ejected correctly the hard drive and connected it to windows, and the system asks me to format my hard drive? same as the usb key Can someone help me please ? Would really appreciate!

    Read the article

  • System does not detect USB pendrives

    - by cshubhamrao
    This USB thing is driving me crazy. 2 problems in time span of 3 hours. Ok I was already trying to cope up with "wrong fs type, bad option, bad superblock" error while mounting FAT Drives when to my amazement I discovered that none of the USB Storage devices showed up in the system Useful outputs: - tail /var/log/syslog: root@shubham-pc:~# tail /var/log/syslog Nov 7 21:41:47 shubham-pc colord: device removed: sysfs-HP-v250w Nov 7 21:41:51 shubham-pc kernel: [ 3441.529542] usb 1-1: USB disconnect, device number 11 Nov 7 21:41:53 shubham-pc kernel: [ 3443.820029] usb 1-2: new high-speed USB device number 14 using ehci-pci Nov 7 21:41:54 shubham-pc kernel: [ 3443.952897] usb 1-2: New USB device found, idVendor=0781, idProduct=5530 Nov 7 21:41:54 shubham-pc kernel: [ 3443.952905] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Nov 7 21:41:54 shubham-pc kernel: [ 3443.952909] usb 1-2: Product: Cruzer Nov 7 21:41:54 shubham-pc kernel: [ 3443.952913] usb 1-2: Manufacturer: SanDisk Nov 7 21:41:54 shubham-pc kernel: [ 3443.952917] usb 1-2: SerialNumber: 20060876420EC6016847 Nov 7 21:41:54 shubham-pc mtp-probe: checking bus 1, device 14: "/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-2" Nov 7 21:41:54 shubham-pc mtp-probe: bus: 1, device: 14 was not an MTP device

    Read the article

  • Remove Write Protection from USB

    - by Vasile Marian Falama?
    My flash USB is write protected and I've tried every possible methods I've encountered over the internet, to get rid of this. Accessing the usb is not working. Format from my computer, is not working. Clear attributes with DiskPart is not working (can't be cleaned, Current Read-only State is Yes but Readonly is set to false... With Disk Management, I can't delete the partition... Is there any other method... With a specific software or somehow? Edit : I tried this on Windows 8.1.

    Read the article

  • Pen drive is recognizing as a USB Internet Dongle which connects to the PC. How do the Pen drive configure well in Ubuntu 12.04?

    - by Eranga Fernando
    Every time I connect my Pen drive it recognizes as more like a Dongle. The reason that I'm telling that if I connect it to the PC when I'm on the INTERNET, it will automatically copy all the files which are in the Dongle. So, I can't recognize which one is the Pen drive when I want to safely remove the device. I'm not sure whether it is the Pen drive or the Dongle..? Can anyone give me a good advice how to solve this problem?

    Read the article

  • configuring USB modem( Huawei EC156) in ubuntu 13.10

    - by user205427
    I am facing difficulty in installing my USB modem in Ubuntu 13.10. Contrary to what many have suggested,it does not get detected automatically, nor does setting a new connection help. USB Device is listed in lsusb, but not under network manager or Devices, it is detected as a CD-ROM, what I understood from the web was that usb-modeswitch can be used to switch it to a USB device. Even 'Enable Mobile Broadband' option is not shown in network manager. What was interesting is when I start laptop with windows 7 and use the USB modem and after that restart with Ubuntu, both Enable Broadband and the mobile broadband connection can be seen. Sadly, internet connection could not be installed. I tried using USB-modeswitch command as suggested somewhere, but it does not seem to work. Following is the message. Take all parameters from the command line * usb_modeswitch: handle USB devices with multiple modes * Version 2.0.1 (C) Josua Dietze 2013 * Based on libusb1/libusbx ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1505 HuaweiMode=1 NeedResponse=0 InquireDevice enabled (default) Look for default devices ... found USB ID 8087:0020 found USB ID 1d6b:0002 found USB ID 0461:4db6 found USB ID 12d1:1505 vendor ID matched product ID matched found USB ID 138a:0007 found USB ID 03f0:231d found USB ID 8087:0020 found USB ID 1d6b:0002 Found devices in default mode (1) Access device 005 on bus 001 Get the current device configuration ... OK, got current device configuration (1) Use interface number 0 Use endpoints 0x08 (out) and 0x87 (in) Inquire device details; driver will be detached ... Looking for active driver ... OK, driver detached INQUIRY message failed (error -9) USB description data (for identification) ------------------------- Manufacturer: HUA?WEI TECHNOLOGIES Product: HUAWEI Mobile Serial No.: ??????????????????? ------------------------- Send old Huawei control message ... -> Run lsusb to note any changes. Bye! I am stuck with this problem for 4 days now, any help would be appreciated

    Read the article

  • All items in my pen drive had been renamed automatically and cannot open it

    - by pabz
    All the items (both files and folders) inside my pen drive had been renamed to some characters like :]h.¡?.A++ and when I try to open any folder Windows gives this message. The filename,directory name, or volume label syntax is incorrect I was told that it is a problem of the pen drive, not a virus. They say if I format the pendrive then I will be able to use it again normally. But I'm not sure. And I need those files. Does anybody knows a solution?

    Read the article

  • Create USB installer from the command line?

    - by j-g-faustus
    I'm trying to create a bootable USB image to install Ubuntu on a new computer. I have done this before following the "create USB drive" instructions for Ubuntu desktop, but I don't have an Ubuntu desktop available. How can I do the same using only the command line? Things I've tried: Create bootable USB on Mac OS X following the ubuntu.com "create USB drive" instructions for Mac: Doesn't boot. usb-creator: According to apt-cache search usb-creator and Wikipedia usb-creator only exists as a graphical tool. "Create manually" instructions at help.ubuntu.com: None of the files and directories described (e.g. casper, filesystem.manifest, menu.lst) exist in the ISO image, and I don't know what has replaced them. unetbootin scripting: Requires X server (graphics support) to run, even when fully scripted. (The command sudo unetbootin lang=en method=diskimage isofile=~/ubuntu-10.10-server-amd64.iso installtype=USB targetdrive=/dev/sdg1 autoinstall=yes gives an error message unetbootin: cannot connect to X server.) Update Also tried GRUB fiddling: Merging information from pendrivelinux.com a related question on the Linux Stackexchange and a grub configuration example I was able to get halfway there - it booted from USB, displayed the grub menu and started the installation, but installation did not complete. For reference, this is the closest I got: sudo su # mount USB pen mount /dev/sd[X]1 /media/usb # install GRUB grub-install --force --no-floppy --root-directory=/media/usb /dev/sd[X] # copy ISO image to USB cp ~/ubuntu-10.10-server-amd64.iso /media/usb # mount ISO image, copy existing grub.cfg mount ~/ubuntu-10.10-server-amd64.iso /media/iso/ -o loop cp /media/iso/boot/grub/grub.cfg /media/usb/boot/grub/ I then edited /media/usb/boot/grub.cfg to add an .iso loopback, example grub entry: menuentry "Install Ubuntu Server" { set gfxpayload=keep loopback loop /ubuntu-10.10-server-amd64.iso linux (loop)/install/vmlinuz file=(loop)/preseed/ubuntu-server.seed iso-scan/filename=/ubuntu-10.10-server-amd64.iso quiet -- initrd (loop)/install/initrd.gz } When booting from USB, this would give me the Grub boot menu and start the installer, but the installer gave up after a couple of screens complaining that it couldn't find the CD-ROM drive. (Naturally, as the box I'm installing on doesn't have an optical drive.) I resolved this particular issue by giving up and doing the "create USB drive" routine using the Ubuntu Live desktop CD (on a computer that does have an optical drive), then the USB install works. But I expect that there is some way to do this from the command line of an Ubuntu system without X server and without an optical drive, so the question still stands. Does anyone know how?

    Read the article

  • accessing live usb files from new hd ubuntu install

    - by Robin Bailey
    After my live USB (ubuntu 12.04 lts) refused to boot, I proceeded to install the same Ubuntu version on the laptop hard drive (a dual boot next to Win xp). This all went well without a hitch. Previous to this, I spent several weeks enjoying and exploring ubuntu from the usb pendrive. During this time I changed lots of settings and customized Firefox and more. Now, I'd like to import the home folder from the usb drive into the new install home folder on the hard disk, which is the purported folder that holds all those special settings to my knowledge. Unfortunately and only being familiar with Windows file systems, the view of the usb file system from the new hdd install is totally perplexing. I can't find anything that looks anywhere close to the original file system. More, I can't find any of the files I had created and stored there, like the LibreOfficeCalc file that has all my passwords (this one is really discouraging) that was stored on the ubuntu desktop. Help me find this file alone and I'll bow down with full apologies to any and all computer gods. Being able to import all those customizing settings into the new install would be a major bonus also, but hey, I'm not greedy. I'll take the passwords file and be happy! And humble! I would be very grateful for some clear, understandable help on this. Thanks

    Read the article

  • How USB drives goes after system hard drives

    - by raihanchy
    I am using Ubuntu 12.04 LTS. My hard drives usually comes as: sda, with 'sudo blkid' and if I plug-in any USB drive, they comes as: sdb, sdc etc; after sda. That's fine!!! But problem arises after I restart my laptop with connecting those USB drives. They alter and comes first and hard drive goes to the end, like: 'sudo blkid' shows, sda, sdb for USB drives and sdc for hard drives. It's making problem to mount with /etc/fstab. I couldn't find any solutions for this. I would like to have any USB drives after my system hard drives, as in Windows. Please, help me at this point. Thanking you. Raihan

    Read the article

  • Is there a better way to run ubuntu from usb disk

    - by Adam Butler
    I have an old laptop with a broken hard drive controller and am running the previous ubuntu from a usb. I installed this as per standard instructions by running some program that copied the live cd to the usb. This has had a few problems, it seems like it was just made for trying and not for everyday use. Ideally I would like to do a proper install to the usb disk instead of just running off the installer disk. Is there a way to do this? The main problems I have are: When adding mounts to fstab it gets overwritten on each reboot When installing updates the kernel cannot be updated

    Read the article

  • Bootable usb stick not boots

    - by Pavaroti Luciano
    i have problem. My bootable usb stick not boots any linux distribution.. it just stop at BIOS, like before turning on OS, but it does nothing. Windows xp/7/8.1 installs boots perfectly. It stopped booting every linux dist. after windows 8.1 installation. Later i deleted windows 8.1 and installed windows 7, and now i want to install ubuntu from usb, but i cant(From disk every linuxOS boots perfectly but not from usb) My computer now is like ~7years old. Specs: CPU: AMD Athlon 64 X2 5000+ Motherboard: GIGABYTE GA-M56S-S3 Video card: Nvidia n210 EDIT: It boots on my other laptop..its bootable, but from this.. NOpe, only windows installs

    Read the article

  • Autoplay for USB drive keeps popping up

    - by Adam Haile
    I have a Seagate external 2TB USB drive that when I leave it plugged in, the Autoplay dialog asking what to do with the drive pops up about once every 30-60 minutes. No matter how many times I tell it to go away, it keeps coming back. I have tried multiple power supplies, USB cables, and all the USB ports on my machine...but it keeps doing the same thing. Also, this does not happen with the same drive on a different computer. Could this be some power or configuration setting that is causing this? I'm running Windows 7 x64 (the computer it works on is x86)

    Read the article

  • Mouse takes a while to start working after boot

    - by warkior
    I just recently installed Ubuntu 12.04 (64 bit) and a number of my USB devices have stopped working. At least, they don't work for the first 3-5 minutes. I have two mice (one wireless, one wired) and a camera, which seem to take Ubuntu 3-5 minutes to recognize after booting up. Eventually, they do start to work, but it takes ages! lsusb results: (when the mice are working...) $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c512 Logitech, Inc. LX-700 Cordless Desktop Receiver Bus 003 Device 003: ID 03f0:3f11 Hewlett-Packard PSC-1315/PSC-1317 Bus 006 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 006 Device 003: ID 046d:c52b Logitech, Inc. Unifying Receiver syslog entries for what seems (to my very untrained eye) to be the problem: Oct 12 20:12:51 REMOVED-GA-MA785GM-US2H kernel: [ 17.420117] usb 2-3: device descriptor read/64, error -110 Oct 12 20:12:57 REMOVED-GA-MA785GM-US2H goa[1879]: goa-daemon version 3.4.0 starting [main.c:112, main()] Oct 12 20:13:06 REMOVED-GA-MA785GM-US2H kernel: [ 32.636107] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:06 REMOVED-GA-MA785GM-US2H kernel: [ 32.852122] usb 2-3: new high-speed USB device number 3 using ehci_hcd Oct 12 20:13:21 REMOVED-GA-MA785GM-US2H kernel: [ 47.964131] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:37 REMOVED-GA-MA785GM-US2H kernel: [ 63.180115] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:37 REMOVED-GA-MA785GM-US2H kernel: [ 63.396126] usb 2-3: new high-speed USB device number 4 using ehci_hcd Oct 12 20:13:47 REMOVED-GA-MA785GM-US2H kernel: [ 73.804158] usb 2-3: device not accepting address 4, error -110 Oct 12 20:13:47 REMOVED-GA-MA785GM-US2H kernel: [ 73.916190] usb 2-3: new high-speed USB device number 5 using ehci_hcd Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.324160] usb 2-3: device not accepting address 5, error -110 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.324197] hub 2-0:1.0: unable to enumerate USB device on port 3 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: failed to claim interface Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: Failed to get parent Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: device devpath is /devices/pci0000:00/0000:00:12.0/usb3/3-3 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: MFG:hp MDL:psc 1310 series SERN:CN47CB60BJO2 serial:CN47CB60BJO2 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.768132] usb 5-3: new full-speed USB device number 2 using ohci_hcd Oct 12 20:14:01 REMOVED-GA-MA785GM-US2H udev-configure-printer: no corresponding CUPS device found Oct 12 20:14:13 REMOVED-GA-MA785GM-US2H kernel: [ 99.904185] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:29 REMOVED-GA-MA785GM-US2H kernel: [ 115.144188] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:29 REMOVED-GA-MA785GM-US2H kernel: [ 115.384178] usb 5-3: new full-speed USB device number 3 using ohci_hcd Oct 12 20:14:44 REMOVED-GA-MA785GM-US2H kernel: [ 130.520196] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:59 REMOVED-GA-MA785GM-US2H kernel: [ 145.760179] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:59 REMOVED-GA-MA785GM-US2H kernel: [ 146.000173] usb 5-3: new full-speed USB device number 4 using ohci_hcd Oct 12 20:15:10 REMOVED-GA-MA785GM-US2H kernel: [ 156.408168] usb 5-3: device not accepting address 4, error -110 Oct 12 20:15:10 REMOVED-GA-MA785GM-US2H kernel: [ 156.544188] usb 5-3: new full-speed USB device number 5 using ohci_hcd Oct 12 20:15:20 REMOVED-GA-MA785GM-US2H kernel: [ 166.952181] usb 5-3: device not accepting address 5, error -110 Oct 12 20:15:20 REMOVED-GA-MA785GM-US2H kernel: [ 166.952215] hub 5-0:1.0: unable to enumerate USB device on port 3 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.216164] usb 6-2: new low-speed USB device number 2 using ohci_hcd Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:13.1/usb6/6-2" Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: bus: 6, device: 2 was not an MTP device Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.396138] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/input/input16 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.396442] generic-usb 0003:046D:C00C.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:13.1-2/input0 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.660187] usb 6-3: new full-speed USB device number 3 using ohci_hcd Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: checking bus 6, device 3: "/sys/devices/pci0000:00/0000:00:13.1/usb6/6-3" Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: bus: 6, device: 3 was not an MTP device Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.859045] logitech-djreceiver 0003:046D:C52B.0006: hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3/input2 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.865086] input: Logitech Unifying Device. Wireless PID:400a as /devices/pci0000:00/0000:00:13.1/usb6/6-3/6-3:1.2/0003:046D:C52B.0006/input/input17 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.865291] logitech-djdevice 0003:046D:C52B.0007: input,hidraw4: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:400a] on usb-0000:00:13.1-3:1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2040: invalid product id string ret=-1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2045: invalid serial id string ret=-1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2050: invalid manufacturer string ret=-1

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >