Search Results

Search found 7779 results on 312 pages for 'usb to parallel'.

Page 3/312 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Is there a better way to run ubuntu from usb disk

  - by Adam Butler

  I have an old laptop with a broken hard drive controller and am running the previous ubuntu from a usb. I installed this as per standard instructions by running some program that copied the live cd to the usb. This has had a few problems, it seems like it was just made for trying and not for everyday use. Ideally I would like to do a proper install to the usb disk instead of just running off the installer disk. Is there a way to do this? The main problems I have are: When adding mounts to fstab it gets overwritten on each reboot When installing updates the kernel cannot be updated

  Read the article

• Bootable usb stick not boots

  - by Pavaroti Luciano

  i have problem. My bootable usb stick not boots any linux distribution.. it just stop at BIOS, like before turning on OS, but it does nothing. Windows xp/7/8.1 installs boots perfectly. It stopped booting every linux dist. after windows 8.1 installation. Later i deleted windows 8.1 and installed windows 7, and now i want to install ubuntu from usb, but i cant(From disk every linuxOS boots perfectly but not from usb) My computer now is like ~7years old. Specs: CPU: AMD Athlon 64 X2 5000+ Motherboard: GIGABYTE GA-M56S-S3 Video card: Nvidia n210 EDIT: It boots on my other laptop..its bootable, but from this.. NOpe, only windows installs

  Read the article

• Mouse takes a while to start working after boot

  - by warkior

  I just recently installed Ubuntu 12.04 (64 bit) and a number of my USB devices have stopped working. At least, they don't work for the first 3-5 minutes. I have two mice (one wireless, one wired) and a camera, which seem to take Ubuntu 3-5 minutes to recognize after booting up. Eventually, they do start to work, but it takes ages! lsusb results: (when the mice are working...) $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c512 Logitech, Inc. LX-700 Cordless Desktop Receiver Bus 003 Device 003: ID 03f0:3f11 Hewlett-Packard PSC-1315/PSC-1317 Bus 006 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 006 Device 003: ID 046d:c52b Logitech, Inc. Unifying Receiver syslog entries for what seems (to my very untrained eye) to be the problem: Oct 12 20:12:51 REMOVED-GA-MA785GM-US2H kernel: [ 17.420117] usb 2-3: device descriptor read/64, error -110 Oct 12 20:12:57 REMOVED-GA-MA785GM-US2H goa[1879]: goa-daemon version 3.4.0 starting [main.c:112, main()] Oct 12 20:13:06 REMOVED-GA-MA785GM-US2H kernel: [ 32.636107] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:06 REMOVED-GA-MA785GM-US2H kernel: [ 32.852122] usb 2-3: new high-speed USB device number 3 using ehci_hcd Oct 12 20:13:21 REMOVED-GA-MA785GM-US2H kernel: [ 47.964131] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:37 REMOVED-GA-MA785GM-US2H kernel: [ 63.180115] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:37 REMOVED-GA-MA785GM-US2H kernel: [ 63.396126] usb 2-3: new high-speed USB device number 4 using ehci_hcd Oct 12 20:13:47 REMOVED-GA-MA785GM-US2H kernel: [ 73.804158] usb 2-3: device not accepting address 4, error -110 Oct 12 20:13:47 REMOVED-GA-MA785GM-US2H kernel: [ 73.916190] usb 2-3: new high-speed USB device number 5 using ehci_hcd Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.324160] usb 2-3: device not accepting address 5, error -110 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.324197] hub 2-0:1.0: unable to enumerate USB device on port 3 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: failed to claim interface Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: Failed to get parent Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: device devpath is /devices/pci0000:00/0000:00:12.0/usb3/3-3 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: MFG:hp MDL:psc 1310 series SERN:CN47CB60BJO2 serial:CN47CB60BJO2 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.768132] usb 5-3: new full-speed USB device number 2 using ohci_hcd Oct 12 20:14:01 REMOVED-GA-MA785GM-US2H udev-configure-printer: no corresponding CUPS device found Oct 12 20:14:13 REMOVED-GA-MA785GM-US2H kernel: [ 99.904185] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:29 REMOVED-GA-MA785GM-US2H kernel: [ 115.144188] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:29 REMOVED-GA-MA785GM-US2H kernel: [ 115.384178] usb 5-3: new full-speed USB device number 3 using ohci_hcd Oct 12 20:14:44 REMOVED-GA-MA785GM-US2H kernel: [ 130.520196] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:59 REMOVED-GA-MA785GM-US2H kernel: [ 145.760179] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:59 REMOVED-GA-MA785GM-US2H kernel: [ 146.000173] usb 5-3: new full-speed USB device number 4 using ohci_hcd Oct 12 20:15:10 REMOVED-GA-MA785GM-US2H kernel: [ 156.408168] usb 5-3: device not accepting address 4, error -110 Oct 12 20:15:10 REMOVED-GA-MA785GM-US2H kernel: [ 156.544188] usb 5-3: new full-speed USB device number 5 using ohci_hcd Oct 12 20:15:20 REMOVED-GA-MA785GM-US2H kernel: [ 166.952181] usb 5-3: device not accepting address 5, error -110 Oct 12 20:15:20 REMOVED-GA-MA785GM-US2H kernel: [ 166.952215] hub 5-0:1.0: unable to enumerate USB device on port 3 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.216164] usb 6-2: new low-speed USB device number 2 using ohci_hcd Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:13.1/usb6/6-2" Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: bus: 6, device: 2 was not an MTP device Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.396138] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/input/input16 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.396442] generic-usb 0003:046D:C00C.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:13.1-2/input0 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.660187] usb 6-3: new full-speed USB device number 3 using ohci_hcd Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: checking bus 6, device 3: "/sys/devices/pci0000:00/0000:00:13.1/usb6/6-3" Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: bus: 6, device: 3 was not an MTP device Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.859045] logitech-djreceiver 0003:046D:C52B.0006: hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3/input2 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.865086] input: Logitech Unifying Device. Wireless PID:400a as /devices/pci0000:00/0000:00:13.1/usb6/6-3/6-3:1.2/0003:046D:C52B.0006/input/input17 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.865291] logitech-djdevice 0003:046D:C52B.0007: input,hidraw4: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:400a] on usb-0000:00:13.1-3:1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2040: invalid product id string ret=-1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2045: invalid serial id string ret=-1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2050: invalid manufacturer string ret=-1

  Read the article

• Install Ubuntu on USB + Disk Encryption

  - by snipey

  I want to create an Operating System installed upon a USB instead HDD (4 GB) So I wanted to know if there were any special steps for it or simply choosing usb in installation menu. P.S - I want to do full install and not live boot. And After that I want to encrypt the entire Operating System using TrueCypt , guide already present on their website , I just wanted to know if it would be compatible with this method. THanks :)

  Read the article

• USB hub keep changing ports

  - by Danniel Magno

  I have an external powered USB hub and I'm using gammu to send some SMSs, but every time the daemon connect to one specific modem, it has the port changed. Gammu is able to send just one SMS and after that the port is changed. I've already tried using: /dev/ttyUSB3 /dev/serial/by-path/pci-0000:00:0b.0-usb-0:3.4.3:1.0-port0 There is anything to do which will stop the ports to be changed or use any other fixed port? Thanks.

  Read the article

• USB resets with Ubuntu 9.10

  - by Grumbel

  Since the upgrade to Ubuntu 9.10 I have issues with getting USB device resets on my Maxtor OneTouch USB harddrive: Nov 9 20:54:37 localhost kernel: [32459.100021] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 21:54:37 localhost kernel: [36059.100017] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 23:24:37 localhost kernel: [41459.112025] usb 2-2: reset high speed USB device using ehci_hcd and address 4 The device itself continues to work fine, the resets however wake the device out of its sleep state and thus cause it to spin up, which is very annoying. Interestingly, as the log shows, the resets happen at pretty regular intervals (i.e. one hour or half an hour), not randomly. An USB card reader seems to have the same issues, while another USB harddrive from a different manufactor works fine on the same PC. What could be causing this and how could I fix it?

  Read the article

• JVM (embarrasingly) parallel processing libraries/tools

  - by Winterstream

  I am looking for something that will make it easy to run (correctly coded) embarrassingly parallel JVM code on a cluster (so that I can use Clojure + Incanter). I have used Parallel Python in the past to do this. We have a new PBS cluster and our admin will soon set up IPython nodes that use PBS as the backend. Both of these systems make it almost a no-brainer to run certain types of code in a cluster. I made the mistake of using Hadoop in the past (Hadoop is just not suited to the kind of data that I use) - the latency made even small runs execute for 1-2 minutes. Is JPPF or Gridgain better for what I need? Does anyone here have any experience with either? Is there anything else you can recommend?

  Read the article

• How to create a bootable USB stick?

  - by Deborah Shadovitz

  I am looking at this: http://www.ubuntu.com/download/help/create-a-usb-stick-on-ubuntu I need to create a boot disk to test Ubuntu to make sure it will run on a PC (Compaq Mini CQ10-120LA) I was given. I can create the boot disk off of a Mac (in English) or Windows (but Windows is in Spanish and foreign to me). Questions: What format do I choose for the USB stick? (I wish the instructions stated this). What is Dash? (Will I know when I run the installer?) Can I do this from a Mac or Windows computer? Or only from Ubuntu?

  Read the article

• Can not update Natty running from a USB stick

  - by Ingo Gerth

  In a blogpost Jono explained a nice way to test the latest version of Natty. Under point four he proposes: Step 4: Update Although you installed the latest daily you should ensure it is up to date, and you can do this with: sudo apt-get update sudo apt-get upgrade Now, I followed all the steps and am actually writing this question from a session running on a 4GB USB stick. When trying to update the installation though (I just tried to do that using the Update Manager), it always fails because I do not have enough disc space remaining. How can I get Ubuntu to update properly on my USB stick?

  Read the article

• Unable to view USB stick/drive contents

  - by Harshit Sachdeva

  So, I plug-in my USB stick, copy a file from the hard drive to the USB stick, and safely remove the USB stick. I then plug out the USB stick. When I plug the USB stick back into the computer again, the previous contents of the USB stick are all gone. It shows an empty drive. I am using Windows XP SP 2 with an 8 GB USB stick from Transcend.

  Read the article

• USB drives not recognized all of a sudden

  - by Siddharth

  I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. lsusb results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful. Thanks.

  Read the article

• Installing Ubuntu to a USB drive

  - by Carl Smotricz

  I'm having a rough time getting Ubuntu to run from a 250 GB USB hard drive. I booted Ubuntu 9.10 from a CD and ran the regular "install" to the attached USB drive. I used the "advanced" option on the drive partition question to put the boot loader on /dev/sdb (the USB disk) but when I boot the machine it doesn't recognize there's a boot loader on the USB drive (it offers to boot from 2 other devices but not the USB disk). I also tried booting from the Ubuntu CD and using usb-creator-gtk to set up the USB drive. Seems to me this is meant to work with flash drives. I got a bootable USB disk but it looked and worked like the CD, i.e. it gave me options of "live CD" operation, installing, memtest, etc. That's not the way I want to run the system. Some help in installing Ubuntu, bootable into a "full" running system on my USB drive would be appreciated.

  Read the article

• How can I hard reset a USB device?

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on superuser.com as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

• Send raw data to USB parallel port after upgrading to 11.10

  - by zaphod

  I have a laser cutter connected via a generic USB to parallel adapter. The laser cutter speaks HPGL, as it happens, but since this is a laser cutter and not a plotter, I usually want to generate the HPGL myself, since I care about the ordering, speed, and direction of cuts and so on. In previous versions of Ubuntu, I was able to print to the cutter by copying an HPGL file directly to the corresponding USB "lp" device. For example: cp foo.plt /dev/usblp1 Well, I just upgraded to Ubuntu 11.10 oneiric, and I can't find any "lp" devices in /dev anymore. D'oh! What's the preferred way to send raw data to a parallel port in Ubuntu? I've tried System Settings Printing + Add, hoping that I might be able to associate my device with some kind of "raw printer" driver and print to it with a command like lp -d LaserCutter foo.plt But my USB to parallel adapter doesn't seem to show up in the list. What I do see are my HP Color LaserJet, two USB-to-serial adapters, "Enter URI", and "Network Printer". Meanwhile, over in /dev, I do see /dev/ttyUSB0 and /dev/ttyUSB1 devices for the 2 USB-to-serial adapters. I don't see anything obvious corresponding to the HP printer (which was /dev/usblp0 prior to the upgrade), except for generic USB stuff. For example, sudo find /dev | grep lp produces no output. I do seem to be able to print to the HP printer just fine, though. The printer setup GUI gives it a device URI starting with "hp:" which isn't much help for the parallel adapter. The CUPS administrator's guide makes it sound like I might need to feed it a device URI of the form parallel:/dev/SOMETHING, but of course if I had a /dev/SOMETHING I'd probably just go on writing to it directly. Here's what dmesg says after I disconnect and reconnect the device from the USB port: [ 924.722906] usb 1-1.1.4: USB disconnect, device number 7 [ 959.993002] usb 1-1.1.4: new full speed USB device number 8 using ehci_hcd And here's how it shows up in lsusb -v: Bus 001 Device 008: ID 1a86:7584 QinHeng Electronics CH340S Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x1a86 QinHeng Electronics idProduct 0x7584 CH340S bcdDevice 2.52 iManufacturer 0 iProduct 2 USB2.0-Print iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 96mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Device Status: 0x0000 (Bus Powered)

  Read the article

• Send raw data to USB parallel port after upgrading to 11.10 oneiric

  - by zaphod

  I have a laser cutter connected via a generic USB to parallel adapter. The laser cutter speaks HPGL, as it happens, but since this is a laser cutter and not a plotter, I usually want to generate the HPGL myself, since I care about the ordering, speed, and direction of cuts and so on. In previous versions of Ubuntu, I was able to print to the cutter by copying an HPGL file directly to the corresponding USB "lp" device. For example: cp foo.plt /dev/usblp1 Well, I just upgraded to Ubuntu 11.10 oneiric, and I can't find any "lp" devices in /dev anymore. D'oh! What's the preferred way to send raw data to a parallel port in Ubuntu? I've tried System Settings Printing + Add, hoping that I might be able to associate my device with some kind of "raw printer" driver and print to it with a command like lp -d LaserCutter foo.plt But my USB to parallel adapter doesn't seem to show up in the list. What I do see are my HP Color LaserJet, two USB-to-serial adapters, "Enter URI", and "Network Printer". Meanwhile, over in /dev, I do see /dev/ttyUSB0 and /dev/ttyUSB1 devices for the 2 USB-to-serial adapters. I don't see anything obvious corresponding to the HP printer (which was /dev/usblp0 prior to the upgrade), except for generic USB stuff. For example, sudo find /dev | grep lp produces no output. I do seem to be able to print to the HP printer just fine, though. The printer setup GUI gives it a device URI starting with "hp:" which isn't much help for the parallel adapter. The CUPS administrator's guide makes it sound like I might need to feed it a device URI of the form parallel:/dev/SOMETHING, but of course if I had a /dev/SOMETHING I'd probably just go on writing to it directly. Here's what dmesg says after I disconnect and reconnect the device from the USB port: [ 924.722906] usb 1-1.1.4: USB disconnect, device number 7 [ 959.993002] usb 1-1.1.4: new full speed USB device number 8 using ehci_hcd And here's how it shows up in lsusb -v: Bus 001 Device 008: ID 1a86:7584 QinHeng Electronics CH340S Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x1a86 QinHeng Electronics idProduct 0x7584 CH340S bcdDevice 2.52 iManufacturer 0 iProduct 2 USB2.0-Print iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 96mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Device Status: 0x0000 (Bus Powered)

  Read the article

• Choppy USB mice on just one of USB ports

  - by user20532

  I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

  Read the article

• Choppy USB mice on just one of USB ports

  - by user20532

  I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

  Read the article

• External USB 3 drive not recognized

  - by ilan123

  Ubuntu 12.10 64 bit seems not to recognize my external hard disk. It is a Vantec NST-310S3 external disk enclosure with a WD 3TB drive. The disk has two NTFS partitions. My PC is a dual boot system. Under Windows 7 the hard disk works fine but I can't make it work with Ubuntu. When the drive is connected to the PC then the command sudo fdisk -l seems to hang forever. Below are the output of lsusb and cat /proc/partitions without the external drive and then with it connected. I added also the last lines of the dmesg command at the end. First without the drive: ilan@linux:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 13ba:0017 Unknown PS/2 Keyboard+Mouse Adapter Bus 001 Device 004: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Bus 001 Device 005: ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ilan@linux:~$ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 629043200 sda2 8 3 367001600 sda3 8 4 1 sda4 8 5 471859200 sda5 8 6 157286400 sda6 8 7 324115456 sda7 8 8 4101120 sda8 11 0 1048575 sr0 Second with the USB 3 drive: ilan@linux:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 13ba:0017 Unknown PS/2 Keyboard+Mouse Adapter Bus 001 Device 004: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Bus 001 Device 005: ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ilan@linux:~$ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 629043200 sda2 8 3 367001600 sda3 8 4 1 sda4 8 5 471859200 sda5 8 6 157286400 sda6 8 7 324115456 sda7 8 8 4101120 sda8 11 0 1048575 sr0 8 16 2930266584 sdb ilan@linux:~$ lsusb -v -s 004:002 Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. Couldn't open device, some information will be missing Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 9 idVendor 0x174c ASMedia Technology Inc. idProduct 0x55aa bcdDevice 1.00 iManufacturer 2 iProduct 3 iSerial 1 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 44 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk-Only iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 ilan@linux:~$ sudo fdisk -l [sudo] password for ilan: Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf1b4f1ee Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 1258293247 629043200 7 HPFS/NTFS/exFAT /dev/sda3 1258293248 1992296447 367001600 7 HPFS/NTFS/exFAT /dev/sda4 1992298494 3907028991 957365249 f W95 Ext'd (LBA) /dev/sda5 1992298496 2936016895 471859200 7 HPFS/NTFS/exFAT /dev/sda6 2936018944 3250591743 157286400 7 HPFS/NTFS/exFAT /dev/sda7 3250593792 3898824703 324115456 83 Linux /dev/sda8 3898826752 3907028991 4101120 82 Linux swap / Solaris dmesg output after connecting the external drive: [ 23.740567] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 23.740786] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 49.144673] usb 4-1: >new SuperSpeed USB device number 2 using xhci_hcd [ 49.163039] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 49.166789] usb 4-1: >New USB device found, idVendor=174c, idProduct=55aa [ 49.166793] usb 4-1: >New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 49.166796] usb 4-1: >Product: AS2105 [ 49.166799] usb 4-1: >Manufacturer: ASMedia [ 49.166801] usb 4-1: >SerialNumber: 0123456789ABCDEF [ 49.206372] usbcore: registered new interface driver uas [ 49.228891] Initializing USB Mass Storage driver... [ 49.229042] scsi6 : usb-storage 4-1:1.0 [ 49.229115] usbcore: registered new interface driver usb-storage [ 49.229116] USB Mass Storage support registered. [ 64.045528] scsi 6:0:0:0: >Direct-Access WDC WD30 EZRX-00MMMB0 80.0 PQ: 0 ANSI: 0 [ 64.046224] sd 6:0:0:0: >Attached scsi generic sg2 type 0 [ 64.046881] sd 6:0:0:0: >[sdb] Very big device. Trying to use READ CAPACITY(16). [ 64.047610] sd 6:0:0:0: >[sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) [ 64.048368] sd 6:0:0:0: >[sdb] Write Protect is off [ 64.048373] sd 6:0:0:0: >[sdb] Mode Sense: 23 00 00 00 [ 64.048984] sd 6:0:0:0: >[sdb] No Caching mode page present [ 64.048987] sd 6:0:0:0: >[sdb] Assuming drive cache: write through [ 64.049297] sd 6:0:0:0: >[sdb] Very big device. Trying to use READ CAPACITY(16). [ 64.050942] sd 6:0:0:0: >[sdb] No Caching mode page present [ 64.050944] sd 6:0:0:0: >[sdb] Assuming drive cache: write through [ 94.245006] usb 4-1: >reset SuperSpeed USB device number 2 using xhci_hcd [ 94.262553] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 94.263805] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c00 [ 94.263808] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c40 [ 125.262722] usb 4-1: >reset SuperSpeed USB device number 2 using xhci_hcd [ 125.280304] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 125.281511] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c00 [ 125.281516] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c40

  Read the article

• USB modeswitch to mass storage device

  - by Andrew

  I'm trying to install a Sierra AirCard 320U (branded as "Telstra USB 4G") into a VirtualBox Windows XP machine, on an Ubuntu 10.10 host. usb_modeswitch offers me a way to disable the "mass storage device" option, but I can't see a way to permanently re-enable it so it's usable by VirtualBox (device filters briefly detect it but then it disappears again). lsusb shows the device as: 0f3d:68aa Airprime, Incorporated When I first insert the device, it shows as 1199:0fff Sierra Wireless, Inc. Is there any way to re-enable the storage device so VirtualBox can see it?

  Read the article

• Ubuntu 10.10 USB drive not showing

  - by Ben

  USB is detecting but not showing the drives or mount details. Nothing there inside my /media folder and /mnt folder. I already enabled automatic mount and give privilege to user also. My sudo fdisk -l shows like: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d3ba7 Device Boot Start End Blocks Id System /dev/sda1 * 1 29637 238053376 83 Linux /dev/sda2 29637 30402 6142977 5 Extended /dev/sda5 29637 30402 6142976 82 Linux swap / Solaris Any idea?

  Read the article

• Logitech USB headset not working on 12.04

  - by thepeoplescoder

  I've looked around for answers to this question, But none of them seem to work for my particular problem. Obviously my USB headset isn't working, But I might as well share the scenario. I am running Ubuntu 12.04 and I have a Logitech USB headset. The relevant output from dmesg is as follows: [160708.528047] usb 2-1.2: USB disconnect, device number 9 [160768.890123] usb 2-1.2: new full-speed USB device number 10 using ehci_hcd [160768.997578] input: Logitech Logitech USB Headset as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.3/input/input15 [160768.997795] generic-usb 0003:046D:0A0C.0005: input,hidraw0: USB HID v1.00 Device [Logitech Logitech USB Headset] on usb-0000:00:1d.0-1.2/input3 When I go to System Settings - Sound, My headset shows up in both the Output and Input tabs, It is called "Clear Chat Comfort USB Headset" in those tabs, But I doubt that's a serious issue. When I click my headset in either tab to use it, The changes are not remembered when I reopen the sound settings, the built-in audio is still used. Also when I select the headset in the Output tab, and click the Test Sound button to test everything, The sound still comes from my laptop's onboard audio, instead of from my USB headset. Does anyone know how to correct this? I am stumped.

  Read the article

• Booting from USB on Mac Air (using setup_mac_usb_boot.sh)

  - by Mike O

  So, I've been working on this for hours and it's getting a little tiring. As some of you may know, installing Ubuntu on Macs is frequently an adventure, and I'm experiencing that right now. The part I'm hung up on at the moment is making a bootable USB. I would just use a CD, but my laptop is a MacBook Air (which doesn't have a CD drive), and I don't own an external CD drive. I initially attempted to use the command line method supplied by the Ubuntu documentation here: https://help.ubuntu.com/community/How%20to%20install%20Ubuntu%20on%20MacBook%20using%20USB%20Stick However, that wasn't even recognized by rEFIt even when I made a number of different modifications to the process, so I quickly decided to look elsewhere. I came across this guide: https://help.ubuntu.com/community/MacBookAir4-2#Basic_Installation_Instructions This ended up working to a large extent. If I choose the supplied grub from rEFIt, it will bring me to the Ubuntu grub, asking me to try it, install, or check the disk. And if I choose to boot Linux directly from rEFIt, it will bring me to the language selection menu. But when I make my selection from either of these menus it pauses for about ten seconds and then gives me a command line error message. It begins with kernel panic - not syncing timer doesn't work through interrupt, and then shows about eight file names. Does anyone here have any ideas as to what can be causing this? I also tried the script with both Ubuntu 11.10 (the current version when the script was written) and 12.04.

  Read the article

• USB Flash not recognised by Windows and BIOS, but works fine in Linux

  - by bbalegere

  I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

  Read the article

• 'foreach' failing when using Parallel Task Library

  - by Chris Arnold

  The following code creates the correct number of files, but every file contains the contents of the first list. Can anyone spot what I've done wrong please? private IList<List<string>> GetLists() { // Code omitted for brevity... } private void DoSomethingInParallel() { var lists = GetLists(); var tasks = new List<Task>(); var factory = new TaskFactory(); foreach (var list in lists) { tasks.Add(factory.StartNew(() => { WriteListToLogFile(list); })); } Task.WaitAll(tasks.ToArray()); }

  Read the article

• Evaluating a function at a particular value in parallel

  - by Gaurav Kalra

  Hi. The question may seem vague, but let me explain it. Suppose we have a function f(x,y,z ....) and we need to find its value at the point (x1,y1,z1 .....). The most trivial approach is to just replace (x,y,z ...) with (x1,y1,z1 .....). Now suppose that the function is taking a lot of time in evaluation and I want to parallelize the algorithm to evaluate it. Obviously it will depend on the nature of function, too. So my question is: what are the constraints that I have to look for while "thinking" to parallelize f(x,y,z...)? If possible, please share links to study.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >