Search Results

Search found 4707 results on 189 pages for 'wireless designs'.

Page 3/189 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Asus Eee PC 1000HE wireless woes

  - by Vladimir Noobokov

  Ever since I have upgraded my Asus Eee PC 1000HE from Lucid 10.04 to Precise 12.04 I have been having issues with my wireless connections. At first I had wireless dropouts: I would be able to start using wireless, but then after a few minutes the wireless would stop working even though I was still connected to the network. Lately things turned worse: while I connect to my wireless network, it just never works. I tried all sorts of solutions on offer here and in other forums but none worked. At best I got the wireless to work up until I rebooted, at which point I would get the same symptoms again: the wireless network is there, but it's not really working. By now I tried so many different "solutions" I don't know where to start describing them; I have also reinstalled 12.04 several times, enough to make me lose faith in Ubuntu. Help here looks like my last resort. For the record, my Asus Eee PC 1000HE is equipped with an Atheros wireless card. I have reinstalled 12.04, ran all the suggested updates, and receive the following response when I type iwconfig in the terminal: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Arsenal" Mode:Managed Frequency:2.452 GHz Access Point: 00:04:ED:48:67:89 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-29 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:27 Invalid misc:57 Missed beacon:0 eth0 no wireless extensions. Thanks in advance for any help that might be offered.

  Read the article

• broadcom 43225 wireless on acer laptop is disabled

  - by Robbie

  I have a acer aspire 5820T with a broadcom 43225 wireless card. I previously used ubuntu 10.10 and the wireless worked straight away, but when I updated to 11.04 the wireless stopped working. I have managed to get the wireless hardware to switch on for a couple of seconds before turning off (When you turn the wireless on using the manual switch the wireless light stays on for a couple of seconds and in the drop down connections menu the information under wireless networks changes from 'device not ready' to 'Disconnected' but shows no wireless networks despite there being one). So far I have tried installing an additional driver, and also disabling the additional driver and installing b43-fwcutter and firmware b43 installer. There may have been other things that I've found in searches that i've tried but unfortunately I can't remember them. Any help would be appreciated.

  Read the article

• Wireless Bridging between BTVoyager 2500V-8C and Belkin G+ Mimo Or D-link DSL-G604T

  - by Morgeh

  Anyone got any ideas how to set up a wireless network bridge between the routers mentioned above? I have a router connected to the internet in one part of the house (BTVoyager) but the wireless range doesnt reach to the other end of the house :-( I also have two spare wireless routers(Belkin G+ Mimo and D-Link DSL-G604T) but as far as I can tell neither of them support wireless bridging.

  Read the article

• Looking for home networking hardware and software advice

  - by phobos7

  Note: I originally wrote this up in a blog post. I've removed any affiliate links that I put in my original post to ensure I don't annoy anybody. I've recently moved home and I now need to go to the trouble of sorting out my home network yet again. We had Virgin broadband in Hertford but you can't get Virgin in the street we've moved to so I've had to go with O2 Broadband. Normally I prefer to use my own hardward, and previously used the DLink DIR-655 router which was great, but in this situation I am using the O2 Wirelss Box III since I only have an old Netgear DG834PN Wireless G modem router and I'd rather be using Wireless N. Anyway, the place we have moved into has only one phone point in the hallway, has the best TV point in one room and the best place to put the TV and other entertainment stuff in yet another room. So, networking the house up for Internet and TV is required. The diagram below shows the things that I'll have in my home network but there are three points where I'm not quite sure what hardware to us. Wireless Access Point/Bridge, that acts only as a wireless to wire bridge and not an AP, that links up a Media Centre/PC and a couple of consoles to the network. I'm pretty much settled on us an Acer Aspire Revo R3600 as my media PC, probably with Ubuntu or Windows and XBMC installed. Wireless Access Point/Bridge, that acts only as a wireless to wire bridge and not an AP, that links up a device that can decode and stream TV from a TV aerial across the network. The device that is connected to 2). At the moment I'm considering a HDHomeRun by SiliconDust. At the moment I'm considering either the TP LINK TL-WA701ND 150Mbps Wireless Lite N Access Point (very cheap at Amazon) or the Netgear 5 GHz Wireless-N HD Access Point/Bridge. I'd love to get some insight into what you would do in my situation. What Wireless Access Point/Bridge should I put at points 1) and 2)? What device should I choose for point 3) that can decode and stream a TV signal? Is the Acer Aspire Revo R3600 a good choice? ![alt text][6] Note 2: I've also posted this question on AVForums.

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• Wireless on Medion MD96500 (Intel® PRO/Wireless 2200BG) running Windows 7

  - by Jakob Schmitt

  I just installed Windows 7 (32 bit) on a Medion MD96500 (Intel 2200BG Wireless Card) and then installed the Windows Vista (32 bit) driver. Now, in the "device driver window", the Wireless Card is listed as working/active. If I want to set up a wireless connection, however, I always get the error message "No connections available". Pushing the hardware-switch (or however that thing is called, right next to the keyboard) does not seem to have any effect.

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Wireless disconnects every 30 minutes

  - by Kez

  I have had a look through all the related questions and I get the feeling my problem is unique. My wireless connection disconnects every 30 minutes, for maybe 1 to 3 seconds. If I am browsing the web while it happens, I get the page cannot be displayed error message. I have checked the event logs as I was curious to know if there was anything in there. There is. Event 8033: BROWSER - The browser has forced an election on network \Device\NetBT_Tcpip_{B919CC30-25A9-45DD-A09F-549A6262FC9E} because a master browser was stopped. Reported exactly every 30 minutes which coincides with my wireless problem. I am running Windows 7 Ultimate, 32-bit. My wireless is Realtek RTL8187 integrated into a ASUS P5K-E/Wifi motherboard. It is on a workgroup and has never been on a domain. This problem does not affect any other computers. Wireless reception is great, and I have ensured that the wireless unit is transmitting on a frequency not used by any nearby wireless basestations. How can I fix this pesky problem?

  Read the article

• Getting wireless N to work on Dell Vostro 3300?

  - by luisfpg

  I have a Dell Vostro 3300, which has a Broadcom BCM4313 wireless. The point is that I cannot make it work in N mode. NetwotkManager applet says I'm on 54 Mbit/s. Of course, my wireless router is N capable. I've double checked. Anyone knows what to do? Here is the output for lspci -v: 12:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Device 0010 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: wl Kernel modules: wl, brcm80211 Thanks a lot.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• Ubuntu 12.10, Wireless not working

  - by Karthik

  My Laptop is Acer 5742G with "Npilfy 802.11 wireless". I have both windows 7 and Ubuntu 12.10 Earlier when I had Ubuntu 12.04, the wireless was working fine, but after installing 12.10 wireless is not working at all, although it is still working in windows. I am not able to see "Wireless Networks" in the Network Manager nor in the Network Settings. This was the output I got for rfkill 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no This is a snapshot of my Additional Drivers settings. As you can see, the required driver for wireless is installed.

  Read the article

• 12.04 drops Wired Network if Wireless connects

  - by mitt10tim

  This is a little different then most of the questions I have seen here. When I am at my office I keep my Lenovo Thinkpad t61p running Ubuntu 12.04 x64 connected via wired Ethernet. I also typically leave the wireless radios on. After a recent update the behavior of laptop in regards to the networks has changed. It used to be that if the laptop had a wired connection, the wired would supersede the wireless. Now, when I get to work and plug the laptop in and power it up, it connects via wired (correct behavior), shortly after the wireless begins searching for its favorite network (also correct) but as soon as it finds a network to connect to, I lose Internet. If I disconnect from the wireless network, leaving the wireless radios powered on, and refresh the wired connection, all is well again. Powering down the wireless radios also corrects the problem. How can I set this up so that the wired network (if available) always has precedence over the wireless?

  Read the article

• Internet access using Edimax BR-6204WG as NIC

  - by Mat Richardson

  My internet access at home is provided by Virgin Media via their superhub. I have a laptop with no NIC - however I do have a spare wireless router, the Edimax BR-6204WG, which I have been led to believe can be used to bridge wireless connections. Only problem is, I'm not sure how to go about doing this. The manual for the device is here:- http://www.edimax.co.uk/images/Image/manual/Wireless/BR-6204Wg/BR-6204Wg_Manual.pdf Basically, I want to be able to connect the Edimax wireless router to my laptop using ethernet cable and to use it to pick up the wireless connection from my Virgin superhub. I've managed to get so far in some ways, but then I'm stuck.

  Read the article

• What is causing my internet to be slow on one laptop but not the other and only at a distance?

  - by Matt Case

  I have a newer laptop, purchased within the last year (acer aspire 7740). This laptop does not have any problem connecting to wireless networks and indicates that the signal strength is excellent on most of the wireless networks I connect to. When the laptop is within 10 feet of my wireless router it gets 30 down 10 up. When it is farther away than 10 feet it will be lucky to get 3 down and 1 up. I also have an older laptop, purchased in 2005, that has no problems at all at the same range. None of my phones, gaming consoles or tablets have this problem. I am beginning to think that the problem must be some hardware defect with the wireless card. I can provide additional information if needed. Just thought I'd check to see what others thought because I've been working on computers my whole life and have never heard of this happening. I have also tried to change the channels on my wireless router and have had no success with this idea.

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• Wireless Repeating with two Netgear N750 (WNDR4300)

  - by jomo1911

  I have a Netgear N750 as my main router, which connects to the internet via a modem. I have a second Netgear N750 which I want to use to repeat the wireless signal of the main router. I logged in to routerlogin of my main router (192.168.1.1) and set up the "Wireless Repeating Function". I set it as the "Wireless Base Station" and filled in the MAC adress of my second Netgear N750. Then I logged in to routerlogin of my second router and set it up as the "Wireless Repeater", I gave it the IP 192.168.1.11 and filled in the MAC adress of the base station. During the setup of the second router (Repeater) I had to disable all security functions. If I connect to the repeaters' WLAN signal, I get no internet connection. Maybe you can help me, thanks

  Read the article

• Wireless is disabled by hardware switch on Dell Inspiron 1750

  - by lowerkey

  I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

  Read the article

• Wireless broken after latest 12.04 update

  - by inderpaldeol

  I updated 12.04 yesterday and it broke my wireless connection. iwconfig lo no wireless extensions. eth0 no wireless extensions. l@ubuntu:~$ lspci|grep Network 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe In the hardware drivers, I see - rt3090sta is activated but currently not in use. WICD does not show wireless networks. Can someone help me please? Thanks id

  Read the article

• Fedora 12 Wireless problems (Intel Wireless 4965AGN Card)

  - by Ninefingers

  Hi All, I'm having an interesting experience with my wireless card at the moment. Basically, it does like this: I connect to the local wireless network (netgear router) It works, briefly, allowing me to browse a webpage or maybe two, if I'm lucky. It then stops working / sending any packets, whilst reported still connected. Now, me being me I've had a look to see what I can find. wpa_supplicant.log looks like this: Trying to associate with valid_mac:a2:30 (SSID='vennardwireless' freq=2462 MHz) Associated with valid_mac:a2:30 WPA: Key negotiation completed with valid_mac:a2:30 [PTK=CCMP GTK=TKIP] CTRL-EVENT-CONNECTED - Connection to valid_mac:a2:30 completed (reauth) [id=0 id_str=] CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys So that's working fine. dmesg | grep "*iwl*" spits out this: iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 iwlagn 0000:03:00.0: setting latency timer to 64 iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 Registered led device: iwl-phy0::radio Registered led device: iwl-phy0::assoc Registered led device: iwl-phy0::RX Registered led device: iwl-phy0::TX iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 So that's working too. I can also ping 192.168.0.1 -I wlan0 and arping 192.168.0.1 -I wlan0 the router until the network falls over. uname -r:2.6.32.10-90.fc12.x86_64. Laptop is a Core2 Duo (2Ghz) with 3GB RAM. Other symptoms I've noticed are that wireshark freezes when I capture on the "broken" interface until I disconnect. Am using networkmanager as per normal. Stupidly, I can connect to the same router via eth0/a cat6 cable just fine. Everyone else can connect to the AP fine (from Windows). Yes, I'm sat right next to it and not trying to access a hotspot the other side of the world. Any ideas? Is this a broken update? (I intend to reboot and test an older kernel later)? Anyone else come across this? Edit: iwconfig wlan0 rate auto is the settings I'm using for rates. Also, according to networkmanager the network is still connected. Thanks for any pointers / advice.

  Read the article

• Wireless doesn't work on a Lenovo V570

  - by Stephen

  I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Ubuntu 12.04 Freezes w/ Ethernet Unplugged + Wireless Drops (Acer Aspire 5516)

  - by Grand Master T

  Ubuntu 12.04-12.10 32/64 freezes or won't boot if the Ethernet cable is unplugged and will not hold a wireless connection. Here is my scenario... Laptop: Acer Aspire 5516 Wireless card: Broadcom BCM4312 Ubuntu 12.04 32/64 Issues Unity 3d won't load without the Ethernet cable plugged in. If I let it load with Ethernet plugged in, it will freeze once I disconnect the cable. Unity 2d will load without the Ethernet cable plugged. In Unity 2d, wireless cannot hold a connection. I can connect to a Wireless network, but when I try to use it (i.e. open a browser), it disconnects. I can reconnect by disabling wireless (uncheck Enable Wireless), re-enable wireless, and reconnect. But, it will disconnect again once I start using it. Ubuntu 12.10 Issues Since 12.10 only gives me the option to load 3d (I assume), I experience the same thing as the first issue in 12.04. Attempted Solutions Enable networking/LAN in BIOS Set LAN first in boot priority in BIOS Remove STA wireless driver (bcmwl-kernel-source) and install b43 low power driver (firmware-b43-lpphy-installer). Remove default Network Manager and install Wicd. So far, I have had no luck with fixing this issue. Does anyone have any further suggestions?

  Read the article

• Wireless problems with Broadcom BCM4313 with windows7 (duplicate)

  - by user292394

  I have wireless connection problem can't connect my wireless adress lspci -vvnn | grep 14e4 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no lsmod Module Size Used by bnep 19624 2 rfcomm 69160 8 ip6t_REJECT 12939 1 xt_hl 12521 6 ip6t_rt 13537 3 nf_conntrack_ipv6 18894 8 nf_defrag_ipv6 34768 1 nf_conntrack_ipv6 ipt_REJECT 12541 1 xt_LOG 17717 10 xt_limit 12711 13 xt_tcpudp 12884 18 xt_addrtype 12635 4 nf_conntrack_ipv4 15012 8 nf_defrag_ipv4 12758 1 nf_conntrack_ipv4 xt_conntrack 12760 16 ip6table_filter 12815 1 ip6_tables 27025 1 ip6table_filter nf_conntrack_netbios_ns 12665 0 nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns nf_nat_ftp 12770 0 nf_nat 21798 1 nf_nat_ftp nf_conntrack_ftp 18638 1 nf_nat_ftp nf_conntrack 96976 8 nf_nat_ftp,nf_conntrack_netbios_ns,nf_nat,xt_conntrack,nf_conntrack_broadcast,nf_conntrack_ftp,nf_conntrack_ipv4,nf_conntrack_ipv6 iptable_filter 12810 1 ip_tables 27239 1 iptable_filter vx_tables 34059 13 ip6table_filter,xt_hl,ip_tables,xt_tcpudp,xt_limit,xt_conntrack,xt_LOG,iptable_filter,ip6t_rt,ipt_REJECT,ip6_tables,xt_addrtype,ip6t_REJECT uvcvideo 80885 0 videobuf2_vmalloc 13216 1 uvcvideo videobuf2_memops 13362 1 videobuf2_vmalloc snd_hda_codec_hdmi 46207 1 videobuf2_core 40664 1 uvcvideo videodev 134688 2 uvcvideo,videobuf2_core snd_hda_codec_conexant 57441 1 snd_hda_intel 52355 8 snd_hda_codec 192906 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 102099 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 dm_multipath 22873 0 snd_seq_midi_event 14899 1 snd_seq_midi scsi_dh 14882 1 dm_multipath lib80211_crypt_tkip 17619 0 snd_rawmidi 30144 1 snd_seq_midi intel_powerclamp 14705 0 coretemp 13435 0 kvm_intel 143060 0 kvm 451511 1 kvm_intel joydev 17381 0 serio_raw 13462 0 snd_seq 61560 2 snd_seq_midi_event,snd_seq_midi intel_ips 18664 0 wl 4207846 0 snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi btusb 32412 0 bluetooth 395423 22 bnep,btusb,rfcomm snd_timer 29482 2 snd_pcm,snd_seq snd 69238 26 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi lib80211 14381 2 wl,lib80211_crypt_tkip toshiba_bluetooth 12852 0 cfg80211 484040 1 wl lpc_ich 21080 0 fglrx 8085343 190 soundcore 12680 1 snd toshiba_acpi 22901 0 sparse_keymap 13948 1 toshiba_acpi wmi 19177 1 toshiba_acpi amd_iommu_v2 19054 1 fglrx video 19476 0 mei_me 18627 0 mei 82276 1 mei_me mac_hid 13205 0 parport_pc 32701 0 ppdev 17671 0 lp 17759 0 parport 42348 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 52570 0 hid 106148 2 hid_generic,usbhid psmouse 102222 0 ahci 25819 3 libahci 32168 1 ahci atl1c 46086 0 dm_mirror 22135 0 dm_region_hash 20862 1 dm_mirror dm_log 18411 2 dm_region_hash,dm_mirror Can someone give any ideas on how I can fix my wireless

  Read the article

• Wireless doesn't work on a Broadcom BCM4312

  - by Boderick

  As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >