Search Results

Search found 4368 results on 175 pages for 'wireless headset'.

Page 3/175 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Ubuntu 12.04 wireless disabled even though the direct connectin (thru modem) is working fine

  - by user90841

  Need help with my newly installed Ubuntu 12.04 system (dual booting along with Win 7), even thoguh I can use internet using the modem and directly plugging it, the wireless network is disabled and it says firmware missing. I tried the following options: 1) checking to see if the wireless is disabled using the hot keys (F2 or Ctrl+F2, Fn + F2 keys), the wireless is working fine in Win 7 but not in Ubuntu. 2) I am able directly plug the laptop with the modem and able connect to Internet using Ubuntu. 3) From the top right hand menu bar, te Wireless networks options say "device not ready (firmware missing) and the Enable Wireless checkbox is checked. 4) tried the command "rfkill list" , it shows all are NOT blocked. 0: phy0: Wireless LAN soft blocked:no Hard blocked: no 1: dell-wifi: Wireless LAN soft blocked:no Hard blocked: no 2: dell-bluetooth: BlueTooth soft blocked:no Hard blocked: no 3: hci0 Bluetooth soft blocked:no Hard blocked: no 5) ifconfig command shows eth0 and lo (lcoalhost) up and running but the wlan0 option is not available to show unless I type ifconfig -a, when it shows wlan0 but its down. 6) The command lspci -vvnn | grep 14e4 shows 04:00.0 network Controller [0280]: Broadcom Corp BCM4312 802.11b/g LP-PHY [14e4:4315] {rev 01) 08:00.0 Ethernet Controller [0200]: Broadcom Corp Netlink BCM5784M Gigabit Ethernet PCIe [1434:1698] {rev 10) 7) The file /var/lib/NetworkManager/NetworkManager.state shows all options are true (networking enabled, wireless enabled, wwlanenabled and wimaxenabled all options are set to true). 8) 'additional drivers' in your Dash and/or Preferences do not bring up anything at all. 9) output for lshw -C network shows *-network DISABLED description : Wireless interface physical id: 4 logical name: wlan0 serial: 78:e4_00"43:b6:ab capabilities: ethernet physical wireless Configuration: broadcast=yes driver=b43 driverversion=3.2.0.29-generic-pae firmware=N/A link=no multicast= yes wireless=IEEE 802.11bg

  Read the article

• Speakers will not work after I use USB Headset

  - by Josh K

  I am trying to configure my SteelSeries Siberia V2 Frost USB Headset to work with my 2.0 speakers using a jack. My goal is to find a easy way (no restart) to switch playback from my headset and my speakers and vice-versa. If i plug my headset in and make it the default device then restart my application/web page then the sounds works out of headset. If I switch the default to my speakers and restart apps/web pages then sound does not play. I know my speakers are on because if I configure them through windows and test, the sounds play, and sounds also play when I test it through my audio manager. Even if I unplug my headset, I still cannot get sound out of my speakers unless I restart My audio manager is RealTek HD Audio Manager, Windows 7 x64. I have tried the speaker back, usb front. speaker front, usb in front port. I have not tried speaker back, usb back.

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Trust Bluetooth 4.0 and Bluetooth Headset

  - by Seregwethrin

  Firstly, I'm writing this after 5 hours of nonstop struggle to make it work, so I searched into the deepest websites from Google, and tried many things. I have Trust Bluetooth 4.0 USB adapter (link) Samsung HM1500 Bluetooth Headset Windows 7 64-bit Desktop PC Facts Nothing wrong with the headset. (it works, tested on a phone and a laptop. Problem is all about bluetooth dongle and its driver.) Trust BT adapter can send and receive files even without any driver. I can pair successfully without any driver too. In Headset's Properties, Services tab, Handsfree and Headset services are checked. Problem When I pair with my BT headset, I cannot see it as a sound playback device. Also when I double-click the headset device icon in Bluetooth Devices, in laptop: it opens a connection window where I can connect and disconnect to that device - perfect! in desktop: it opens the properties window, even though Handsfree and Headset services are checked (I check them explicitly, in laptop they came as already checked) - Problem! Unsuccessful driver installations The driver on the Trust's website says "Error 1606 Could not access Network Location" on start, so it doesn't get installed. The driver on Broadcom (link) is being closed with Windows's that classic "has stopped working" error on validation step, so it doesn't get installed too. (Those tests made more than once) Successful installation In the Win64 folder of Trust's driver from their website, if I install through "BTW.msi", it doesn't give me Error 1606 and it gets installed. Then the problem: When I try to start bluetooth from start menu (or it gets started at Windows startup), an error popup says: "BtBalloon.dll is missing..." so it doesn't start. I found BBalloon.dll in the driver folder, I renamed it to BtBalloon.dll, moved into Windows/system32 and Windows/SysWOW64 folders, and it seems working. Or maybe it gets closed behind the scenes. The bluetooth icon is there with or without this driver since Windows has it. Bluetooth Peripheral Device First it didn't get installed from Windows Update. After, I showed the driver folder path in Device Manager and pressed "Explore in this location". Surprisingly, it's being found as "Handsfree" driver. Now even I uninstall the drivers, it still can see the Handsfree. But still, no playback device. Any ideas to guide me? I'm out of ideas.

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• Using a Linksys Wireless- G Broadband Router for a Wireless Antenna/Adapter?

  - by Alex

  (Warning: I'm not too computer-smart). Just moved fm a home where I used ATT DSL to a home w/ Comcast Cable for internet. Old home had the DSL ethernet wired to my only desktop w/ a 2Wire router for my wireless signal for the laptops. In the new home the signal comes fm cable via a Netgear(300) wireless router (remotely located) & works fine for my laptops. After searching with the network software, my desktop (can't be ethernet wired cuz of location) detects no wireless signal. Desktop is a 2 yr old HP p6311f Pavilion (Windows 7). Can't seem to detect any wireless hardware (ant/adaptr). Maybe I don't have the ability & need to buy a USB wireless antenna? Would the Pavilion come w/ wireless capability out of the box, maybe something inside the tower? No antenna on back. I happen to have a Linksys Wireless router which I plugged in to the desktop (trying both internet & shared ports) & noticed signal action on the router front panel. No internet on desktop though. Can I use this as an antenna for the desktop? Thanks & sorry if my solution is an easy one I'm just missing. Just want internet on the desktop.

  Read the article

• Asus Eee PC 1000HE wireless woes

  - by Vladimir Noobokov

  Ever since I have upgraded my Asus Eee PC 1000HE from Lucid 10.04 to Precise 12.04 I have been having issues with my wireless connections. At first I had wireless dropouts: I would be able to start using wireless, but then after a few minutes the wireless would stop working even though I was still connected to the network. Lately things turned worse: while I connect to my wireless network, it just never works. I tried all sorts of solutions on offer here and in other forums but none worked. At best I got the wireless to work up until I rebooted, at which point I would get the same symptoms again: the wireless network is there, but it's not really working. By now I tried so many different "solutions" I don't know where to start describing them; I have also reinstalled 12.04 several times, enough to make me lose faith in Ubuntu. Help here looks like my last resort. For the record, my Asus Eee PC 1000HE is equipped with an Atheros wireless card. I have reinstalled 12.04, ran all the suggested updates, and receive the following response when I type iwconfig in the terminal: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Arsenal" Mode:Managed Frequency:2.452 GHz Access Point: 00:04:ED:48:67:89 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-29 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:27 Invalid misc:57 Missed beacon:0 eth0 no wireless extensions. Thanks in advance for any help that might be offered.

  Read the article

• broadcom 43225 wireless on acer laptop is disabled

  - by Robbie

  I have a acer aspire 5820T with a broadcom 43225 wireless card. I previously used ubuntu 10.10 and the wireless worked straight away, but when I updated to 11.04 the wireless stopped working. I have managed to get the wireless hardware to switch on for a couple of seconds before turning off (When you turn the wireless on using the manual switch the wireless light stays on for a couple of seconds and in the drop down connections menu the information under wireless networks changes from 'device not ready' to 'Disconnected' but shows no wireless networks despite there being one). So far I have tried installing an additional driver, and also disabling the additional driver and installing b43-fwcutter and firmware b43 installer. There may have been other things that I've found in searches that i've tried but unfortunately I can't remember them. Any help would be appreciated.

  Read the article

• Static background noise while using new headset Ubuntu 13.04

  - by ThundLayr

  Today I bought a new gaming headset (Gx-Gaming Lychas), and when I tried to record some gameplay-comentary I noticed that there always is a static background noise, I just recorded an example so you guys can listen it (no downloaded needed): http://www47.zippyshare.com/v/65167832/file.html I'm using Kubuntu 13.04 and Kernel version is 3.8.0-19, my laptop is an Acer Travelmate 5760Z, I tried tons of configurations on Alsamixer and none of them made result, I really need to get this working so any kind of help will be very aprecciated. cat /proc/asound/cards: 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xc6400000 irq 44 cat /proc/asound/card0/codec#0 Codec: Conexant CX20588 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x14f1506c Subsystem Id: 0x10250574 Revision Id: 0x100003 No Modem Function Group found Default PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A State of AFG node 0x01: Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS Power: setting=D0, actual=D0 GPIO: io=4, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Headphone Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Headphone Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x4a 0x4a] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Speaker Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Speaker Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x80 0x80] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out Control: name="Beep Playback Volume", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Control: name="Beep Playback Switch", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0 Amp-Out vals: [0x00] Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Control: name="Capture Volume", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Control: name="Capture Switch", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x50 0x50] [0x80 0x80] [0x80 0x80] [0x80 0x80] Converter: stream=4, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Control: name="Mic Boost Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x04 0x04] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a 0x1b* 0x1d 0x1e Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a* 0x1b 0x1d 0x1e Node 0x19 [Pin Complex] wcaps 0x400581: Stereo Control: name="Headphone Jack", index=0, device=0 Pincap 0x0000001c: OUT HP Detect Pin Default 0x04214040: [Jack] HP Out at Ext Right Conn = 1/8, Color = Green DefAssociation = 0x4, Sequence = 0x0 Pin-ctls: 0xc0: OUT HP Unsolicited: tag=01, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1a [Pin Complex] wcaps 0x400481: Stereo Control: name="Internal Mic Phantom Jack", index=0, device=0 Pincap 0x00001324: IN Detect Vref caps: HIZ 50 80 Pin Default 0x90a70130: [Fixed] Mic at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0x3, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1b [Pin Complex] wcaps 0x400581: Stereo Control: name="Mic Jack", index=0, device=0 Pincap 0x00011334: IN OUT EAPD Detect Vref caps: HIZ 50 80 EAPD 0x0: Pin Default 0x04a19020: [Jack] Mic at Ext Right Conn = 1/8, Color = Pink DefAssociation = 0x2, Sequence = 0x0 Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=02, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1c [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00000014: OUT Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1d [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00010034: IN OUT EAPD Detect EAPD 0x0: Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1e [Pin Complex] wcaps 0x400481: Stereo Pincap 0x00000024: IN Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Control: name="Speaker Phantom Jack", index=0, device=0 Pincap 0x00000010: OUT Pin Default 0x92170110: [Fixed] Speaker at Int Front Conn = Analog, Color = Unknown DefAssociation = 0x1, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11* Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x12 Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x21 Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0 Amp-In vals: [0x00 0x00] Pincap 0x00000020: IN Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11 Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono

  Read the article

• Wireless Bridging between BTVoyager 2500V-8C and Belkin G+ Mimo Or D-link DSL-G604T

  - by Morgeh

  Anyone got any ideas how to set up a wireless network bridge between the routers mentioned above? I have a router connected to the internet in one part of the house (BTVoyager) but the wireless range doesnt reach to the other end of the house :-( I also have two spare wireless routers(Belkin G+ Mimo and D-Link DSL-G604T) but as far as I can tell neither of them support wireless bridging.

  Read the article

• Looking for home networking hardware and software advice

  - by phobos7

  Note: I originally wrote this up in a blog post. I've removed any affiliate links that I put in my original post to ensure I don't annoy anybody. I've recently moved home and I now need to go to the trouble of sorting out my home network yet again. We had Virgin broadband in Hertford but you can't get Virgin in the street we've moved to so I've had to go with O2 Broadband. Normally I prefer to use my own hardward, and previously used the DLink DIR-655 router which was great, but in this situation I am using the O2 Wirelss Box III since I only have an old Netgear DG834PN Wireless G modem router and I'd rather be using Wireless N. Anyway, the place we have moved into has only one phone point in the hallway, has the best TV point in one room and the best place to put the TV and other entertainment stuff in yet another room. So, networking the house up for Internet and TV is required. The diagram below shows the things that I'll have in my home network but there are three points where I'm not quite sure what hardware to us. Wireless Access Point/Bridge, that acts only as a wireless to wire bridge and not an AP, that links up a Media Centre/PC and a couple of consoles to the network. I'm pretty much settled on us an Acer Aspire Revo R3600 as my media PC, probably with Ubuntu or Windows and XBMC installed. Wireless Access Point/Bridge, that acts only as a wireless to wire bridge and not an AP, that links up a device that can decode and stream TV from a TV aerial across the network. The device that is connected to 2). At the moment I'm considering a HDHomeRun by SiliconDust. At the moment I'm considering either the TP LINK TL-WA701ND 150Mbps Wireless Lite N Access Point (very cheap at Amazon) or the Netgear 5 GHz Wireless-N HD Access Point/Bridge. I'd love to get some insight into what you would do in my situation. What Wireless Access Point/Bridge should I put at points 1) and 2)? What device should I choose for point 3) that can decode and stream a TV signal? Is the Acer Aspire Revo R3600 a good choice? ![alt text][6] Note 2: I've also posted this question on AVForums.

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• Wireless on Medion MD96500 (Intel® PRO/Wireless 2200BG) running Windows 7

  - by Jakob Schmitt

  I just installed Windows 7 (32 bit) on a Medion MD96500 (Intel 2200BG Wireless Card) and then installed the Windows Vista (32 bit) driver. Now, in the "device driver window", the Wireless Card is listed as working/active. If I want to set up a wireless connection, however, I always get the error message "No connections available". Pushing the hardware-switch (or however that thing is called, right next to the keyboard) does not seem to have any effect.

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Wireless disconnects every 30 minutes

  - by Kez

  I have had a look through all the related questions and I get the feeling my problem is unique. My wireless connection disconnects every 30 minutes, for maybe 1 to 3 seconds. If I am browsing the web while it happens, I get the page cannot be displayed error message. I have checked the event logs as I was curious to know if there was anything in there. There is. Event 8033: BROWSER - The browser has forced an election on network \Device\NetBT_Tcpip_{B919CC30-25A9-45DD-A09F-549A6262FC9E} because a master browser was stopped. Reported exactly every 30 minutes which coincides with my wireless problem. I am running Windows 7 Ultimate, 32-bit. My wireless is Realtek RTL8187 integrated into a ASUS P5K-E/Wifi motherboard. It is on a workgroup and has never been on a domain. This problem does not affect any other computers. Wireless reception is great, and I have ensured that the wireless unit is transmitting on a frequency not used by any nearby wireless basestations. How can I fix this pesky problem?

  Read the article

• Getting wireless N to work on Dell Vostro 3300?

  - by luisfpg

  I have a Dell Vostro 3300, which has a Broadcom BCM4313 wireless. The point is that I cannot make it work in N mode. NetwotkManager applet says I'm on 54 Mbit/s. Of course, my wireless router is N capable. I've double checked. Anyone knows what to do? Here is the output for lspci -v: 12:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Device 0010 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: wl Kernel modules: wl, brcm80211 Thanks a lot.

  Read the article

• Samsung Galaxy S II bluetooth headset

  - by tumchaaditya

  I want to buy a stereo bluetooth headset for Galaxy SII and Galaxy SIII. I am not asking for any product recommendation. But, I just want to be sure that I will be able to receive phone calls using the button on headset as well as listen music in stereo(which will be taken care of by A2DP). So, any guidelines on choosing the headsets? What to look for to ensure that the buttons on the headset work?

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• Ubuntu 12.10, Wireless not working

  - by Karthik

  My Laptop is Acer 5742G with "Npilfy 802.11 wireless". I have both windows 7 and Ubuntu 12.10 Earlier when I had Ubuntu 12.04, the wireless was working fine, but after installing 12.10 wireless is not working at all, although it is still working in windows. I am not able to see "Wireless Networks" in the Network Manager nor in the Network Settings. This was the output I got for rfkill 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no This is a snapshot of my Additional Drivers settings. As you can see, the required driver for wireless is installed.

  Read the article

• 12.04 drops Wired Network if Wireless connects

  - by mitt10tim

  This is a little different then most of the questions I have seen here. When I am at my office I keep my Lenovo Thinkpad t61p running Ubuntu 12.04 x64 connected via wired Ethernet. I also typically leave the wireless radios on. After a recent update the behavior of laptop in regards to the networks has changed. It used to be that if the laptop had a wired connection, the wired would supersede the wireless. Now, when I get to work and plug the laptop in and power it up, it connects via wired (correct behavior), shortly after the wireless begins searching for its favorite network (also correct) but as soon as it finds a network to connect to, I lose Internet. If I disconnect from the wireless network, leaving the wireless radios powered on, and refresh the wired connection, all is well again. Powering down the wireless radios also corrects the problem. How can I set this up so that the wired network (if available) always has precedence over the wireless?

  Read the article

• Internet access using Edimax BR-6204WG as NIC

  - by Mat Richardson

  My internet access at home is provided by Virgin Media via their superhub. I have a laptop with no NIC - however I do have a spare wireless router, the Edimax BR-6204WG, which I have been led to believe can be used to bridge wireless connections. Only problem is, I'm not sure how to go about doing this. The manual for the device is here:- http://www.edimax.co.uk/images/Image/manual/Wireless/BR-6204Wg/BR-6204Wg_Manual.pdf Basically, I want to be able to connect the Edimax wireless router to my laptop using ethernet cable and to use it to pick up the wireless connection from my Virgin superhub. I've managed to get so far in some ways, but then I'm stuck.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >