Search Results

Search found 3993 results on 160 pages for 'broken pipe'.

Page 30/160 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

  • New SSD, is the MBR broken? DISK BOOT FAILURE

    - by Shevek
    I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

    Read the article

  • m not able to connect to wifi network

    - by Broken Heart
    i had tried every code every idea every thing but i failed wiireless driver broadcom bcm43412 but when i checked pci-id it show not supported my pci id is 14e4:4365 and chip id is BCM43142 i tried edit connection myself to olso but i cannt wat to put in clone mac adress place? device mac adress is the router mac adress but what is clone mac adress i had placed my laptop mac adress in place of clone mac adress bt it doesnot work tried every thing but it not work checked additional driver by going system settings it doesnot contain any drivers,tried internet by cable then it connects then how sholud i correct this plz tell

    Read the article

  • Relaying to tech "support" that computer is actually broken.

    - by Sion
    First some background: I have a Dell Inspiron 15R M050, it is still under the Dell limited warranty and the Best Buy Extended warranty. I am currently dual booting Debian Squeeze and Windows 7, the only reason I go into Windows is to play video games specifically steam games. Issue: When I play my games in Windows I am capable of playing for anywhere from 5 minutes to 2 hours before I suffer a hard-lock. I cannot alt-tab, ctrl-alt-delete, ctrl-shift-escape do anything for 2-3 minutes. After this hard-lock period everything runs fine, I can continue the game for probably another hour at least before I suffer another lock. Games: Borderlands, Splinter Cell: Chaos Theory, Starcraft 2, Garrys Mod What I have tried: Running the diagnostic suite in the dell bios, restoring the OEM Windows recovery partition on the HD, fresh installing Windows 7 Professional, updating BIOS, Calling tech support and having them run a software Hardware Diagnostics suite. The question: I think from the research that I have performed that it might be a lack of thermal paste on the CPU, would I be able to go to Best Buy and have them do a hardware diagnostic from the hardware level then have them be able to tell Dell that there is a hardware issue? Or would there be a different problem?

    Read the article

  • I tried to update from 13.04 to 13.10. Got the "Could not calculate the upgrade" error

    - by Siddharth
    I ran grep Broken /var/log/dist-upgrade/apt.log Here is what I got Broken libpam-systemd:i386 Conflicts on libpam-xdg-support [ i386 ] < 0.2-0ubuntu2 > ( universe/admin ) Broken iputils-ping:i386 Depends on libgnutls-openssl27 [ i386 ] < none -> 2.12.23-1ubuntu1 > ( libs ) Broken ubuntu-standard:i386 Depends on dnsutils [ i386 ] < none -> 1:9.9.2.dfsg.P1-2ubuntu2 > ( net )` I would appreciate your help in resolving this error. Thanks :)

    Read the article

  • Apache2 Virtual Host broken; displayed default index.html on subdomain, but correct content on www.subdomain

    - by Robert K
    I've got a Linode configured as a Ubuntu 10.04.2 web server with Apache 2.2.14. I have a total of 4 sites, all defined under /etc/apache2/sites-available as virtual hosts. All sites are almost identical clones for configuration. And all sites but my last work successfully. default: (www.)exampleadnetwork.com (www.)example.com reseller.example.com trouble: client1.example.com I keep getting this page when I visit the client1.example.com site: It works! This is the default web page for this server. The web server software is running but no content has been added, yet. In my ports.conf file I have the NameVirtualHost correctly set to my IP address on port 80. If I access the "www.sub.example.com" alias the site works! If I access it without the www I see the "It Works" excerpt posted above. Even apache2ctl -S shows that my vhost file parses correctly and is added to the mix. My vhost configuration file is as follows: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName client1.example.com ServerAlias client1.example.com www.client1.example.com DocumentRoot /srv/www/client1.example.com/public_html/ ErrorLog /srv/www/client1.example.com/logs/error.log CustomLog /srv/www/client1.example.com/logs/access.log combined <directory /srv/www/client1.example.com/public_html/> Options -Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </directory> </VirtualHost> The other sites are variations of: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName example.com ServerAlias example.com www.example.com DocumentRoot /srv/www/example.com/public_html/ ErrorLog /srv/www/example.com/logs/error.log CustomLog /srv/www/example.com/logs/access.log combined </VirtualHost> The only site the differs is the other subdomain: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName reseller.example.com ServerAlias reseller.example.com DocumentRoot /srv/www/reseller.example.com/public_html/ ErrorLog /srv/www/reseller.example.com/logs/error.log CustomLog /srv/www/reseller.example.com/logs/access.log combined </VirtualHost> Filenames are the FQDN without the www. prefix. I've followed this advice, but still cannot access subdomain properly.

    Read the article

  • Broken Vista. Can't open Windows settings.

    - by serena
    My neighbor has a Lenovo laptop with Windows Vista Home Basic. She's a noob and just uses the laptop for internet purposes. She said she had to close down Windows improperly (sometime ago, maybe 6 months) because of system freeze. She realized there's something wrong with her Windows when she tried to open Windows update settings. I took a look at the system and determined the following errors: When I click on Windows Updates, a bare white window opens for a sec. and closes immediately. When I try to open Computer Properties, the same thing happens. (Windows+Break doesn't work either.) When I try to open Bluetooth settings, the same thing happens. So Vista won't let me open any Windows settings, but installed programs work correctly (games, applications etc.). She has no Windows Vista discs since the laptop came with preinstalled genuine Vista. She also has no recovery discs. I don't think there is a system restore point for the time the system was stable. Now what can we do to solve this big problem?

    Read the article

  • Software RAID 1 broken, how do I fix this?

    - by Edward
    I'm running CentOS 6 x86_64. There is a software RAID 1 being used on the two internal 80GB drives. I got the following e-mail sent to me: A DegradedArray event had been detected on md device /dev/md1. Faithfully yours, etc. P.S. The /proc/mdstat file currently contains the following: Personalities : [raid1] md0 : active raid1 sda1[0] 511988 blocks super 1.0 [2/1] [U_] md1 : active raid1 sda2[0] 8190968 blocks super 1.1 [2/1] [U_] bitmap: 1/1 pages [4KB], 65536KB chunk md4 : active raid1 sdc1[0] sdb1[1] 1953512400 blocks super 1.2 [2/2] [UU] md3 : active raid1 sdd5[1] sda5[0] 61224892 blocks super 1.1 [2/2] [UU] bitmap: 1/1 pages [4KB], 65536KB chunk md2 : active raid1 sdd3[1] sda3[0] 8190968 blocks super 1.1 [2/2] [UU] unused devices: <none> The system appears to have booted fine and is working. The two drives' content did not change at all. I only removed and reinstalled them while I was booted on the CentOS Live DVD. How do I get the array working again?

    Read the article

  • How do I find broken symlinks automatically on Windows?

    - by HughG
    Not sure if this is bad style, but I'm asking this question here because I couldn't find the answer elsewhere, and then I worked out one solution on my own. I'd be interested to see other people's solutions, but after a few days I'll post my own. In my specific case, I'm running on Windows 7, but I'd be interested in answers for other/older versions of Windows. I realise that one answer is "install a version of Unix find, and then solve as for Unix", but I wanted a more "native" solution. EDIT 2012-07-17: Clarification: by "automatically" I ideally mean something I can run as part of a script, rather than a GUI tool which does all the work at the press of a button, because I'll want to do this unattended.

    Read the article

  • Is there a good, free way to fix broken/corrupt .wmv files?

    - by chbtn
    I've recovered some files from an hdd that weren't supposed to be deleted in the first place, but they have seeking problems/crash the players. Since they have the right size, I'm thinking it might be a problem of corrupt index/header, so I'm trying to find a way to fix them. It's easy to find examples on how to fix corrupt .avi files with mencoder, but .wmv seems trickier. Also, I realize there might not be a way to fix these files, but I figure I might as well as try. As far as players go, I've tried opening it with vlc/mplayer/windows media player. I can use anything on Windows XP/7 and Ubuntu, as long as it's free. Since the files are 200mb+ and there are quite a few, I don't think trial software would work.

    Read the article

  • What are my options for booting OSX 10.6 when my DVD drive is broken?

    - by Kev
    I'm about to completely re-pave my Mac Mini but the DVD drive has died on me which means I can't boot from the installation media. I know I can boot from a USB stick but I don't have one available, what are my options given the following hardware at hand? Netgear ReadyNAS Duo NAS (NIC or USB only, no Firewire) USB HDD (no Firewire) I've ripped an ISO of the installation disk, can I somehow get the Mini to boot from this image using one of the above? If I decide not to re-pave but just upgrade, can the Mac be upgraded just using an OSX 10.6 ISO image on its disk?

    Read the article

  • Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

    - by AKa
    I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

    Read the article

  • How broken is routing strategy that causes a martian packet (so far only) during tracepath?

    - by lkraav
    I believe I've achieved a table that routes packets from and to eth1/192.168.3.x through 192.168.3.1, and packets from and to eth0/192.168.1.x through 192.168.1.1 (helpful source). Question: when doing tracepath from 192.168.3.20 (from within vserver), I'm getting kernel: [318535.927489] martian source 192.168.3.20 from 212.47.223.33, on dev eth0 at or near the target IP, while intermediary hops go without (log below). I don't understand why this packet is arriving on eth0, instead of eth1, even after reading this: Note that you may see packets from non-routable IP addresses when running the traceroute or tracepath commands. While packets cannot be routed to these routers, packets sent between 2 routers only need to know the address of the next hop within the local networks, which could be a non-routable address. Can someone explain that paragraph in human language? Based on short initial trials so far, everything else seems to work without causing martians. Is this contained to the nature of tracepath operation or do I have some other bigger routing problem that will cause work traffic breakage? Side note: is it possible to inspect martian packet with tcpdump or wireshark or anything of the sort? I'm have not been able to get it to show up on my own. vserver-20 / # tracepath -n 212.47.223.33 1: 192.168.3.2 0.064ms pmtu 1500 1: 192.168.3.1 1.076ms 1: 192.168.3.1 1.259ms 2: 90.191.8.2 1.908ms 3: 90.190.134.194 2.595ms 4: 194.126.123.94 2.136ms asymm 5 5: 195.250.170.22 2.266ms asymm 6 6: 212.47.201.86 2.390ms asymm 7 7: no reply 8: no reply 9: no reply ^C Host routing: $ sudo ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:24:1d:de:b3:5d brd ff:ff:ff:ff:ff:ff inet 192.168.1.2/24 scope global eth0 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:46:46:a3:6a brd ff:ff:ff:ff:ff:ff inet 192.168.3.2/27 scope global eth1 inet 192.168.3.20/27 brd 192.168.3.31 scope global secondary eth1 # linux-vserver instance $ sudo ip route default via 192.168.1.1 dev eth0 metric 3 unreachable 127.0.0.0/8 scope host 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2 192.168.3.0/27 dev eth1 proto kernel scope link src 192.168.3.2 $ sudo ip rule 0: from all lookup local 32764: from all to 192.168.3.0/27 lookup dmz 32765: from 192.168.3.0/27 lookup dmz 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table dmz default via 192.168.3.1 dev eth1 metric 4 192.168.3.0/27 dev eth1 scope link metric 4 Gateway routing # ip route 10.24.0.2 dev tun0 proto kernel scope link src 10.24.0.1 10.24.0.0/24 via 10.24.0.2 dev tun0 192.168.3.0/24 dev br-dmz proto kernel scope link src 192.168.3.1 192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1 $ISP_NET/23 dev eth0.1 proto kernel scope link src $WAN_IP default via $ISP_GW dev eth0.1 Additional background Options for non-virtualized network interface isolation?

    Read the article

  • How to collect figures of traffic used per-host, broken up by time and destination?

    - by Seishun
    We have a relatively small network, all PSs in one subnet. One PC with two NICs and pfSense installed works as a firewall/router. There is an OpenVPN tunnel to a remote location, created as a site-to-site connection to another pfSense box there. I have an assignment to capture, store and show (via a web interface) information on traffic generated (both incoming and outcoming) by each host on our subnet and present it in several views: megabytes per calendar hours / days / months / years (that is, not just "one month back", but "in Dec 2010" and so on); megabytes per destination: VPN to remote location / other destinations / Google Apps servers. I tried the software packages in pfSense that offer traffic montoring - but it seems they don't store the information fixed by months, instead showing the amounts of traffic generated in periods (days/months/etc) calculated from the present moment. I'm also interested in understanding what would be the best way for me to break up traffic by hosts and destinations. I'm open to all suggestions, even if they mean that I will have to understand something new to me.

    Read the article

  • saslauthd + PostFix producing password verification and authentication errors

    - by Aram Papazian
    So I'm trying to setup PostFix while using SASL (Cyrus variety preferred, I was using dovecot earlier but I'm switching from dovecot to courier so I want to use cyrus instead of dovecot) but I seem to be having issues. Here are the errors I'm receiving: ==> mail.log <== Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: SASL authentication failure: Password verification failed Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: ipname[xx.xx.xx.xx]: SASL PLAIN authentication failed: authentication failure ==> mail.info <== Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: SASL authentication failure: Password verification failed Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: ipname[xx.xx.xx.xx]: SASL PLAIN authentication failed: authentication failure ==> mail.warn <== Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: SASL authentication failure: Password verification failed Aug 10 05:11:49 crazyinsanoman postfix/smtpd[779]: warning: ipname[xx.xx.xx.xx]: SASL PLAIN authentication failed: authentication failure I tried $testsaslauthd -u xxxx -p xxxx 0: OK "Success." So I know that the password/user I'm using is correct. I'm thinking that most likely I have a setting wrong somewhere, but can't seem to find where. Here is my files. Here is my main.cf for postfix: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname # This is already done in /etc/mailname #myhostname = crazyinsanoman.xxxxx.com smtpd_banner = $myhostname ESMTP $mail_name #biff = no # appending .domain is the MUA's job. #append_dot_mydomain = no readme_directory = /usr/share/doc/postfix # TLS parameters smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # Relay smtp through another server or leave blank to do it yourself #relayhost = smtp.yourisp.com # Network details; Accept connections from anywhere, and only trust this machine mynetworks = 127.0.0.0/8 inet_interfaces = all #mynetworks_style = host #As we will be using virtual domains, these need to be empty local_recipient_maps = mydestination = # how long if undelivered before sending "delayed mail" warning update to sender delay_warning_time = 4h # will it be a permanent error or temporary unknown_local_recipient_reject_code = 450 # how long to keep message on queue before return as failed. # some have 3 days, I have 16 days as I am backup server for some people # whom go on holiday with their server switched off. maximal_queue_lifetime = 7d # max and min time in seconds between retries if connection failed minimal_backoff_time = 1000s maximal_backoff_time = 8000s # how long to wait when servers connect before receiving rest of data smtp_helo_timeout = 60s # how many address can be used in one message. # effective stopper to mass spammers, accidental copy in whole address list # but may restrict intentional mail shots. smtpd_recipient_limit = 16 # how many error before back off. smtpd_soft_error_limit = 3 # how many max errors before blocking it. smtpd_hard_error_limit = 12 # Requirements for the HELO statement smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit # Requirements for the sender details smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit # Requirements for the connecting server smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org # Requirement for the recipient address smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining # require proper helo at connections smtpd_helo_required = yes # waste spammers time before rejecting them smtpd_delay_reject = yes disable_vrfy_command = yes # not sure of the difference of the next two # but they are needed for local aliasing alias_maps = hash:/etc/postfix/aliases alias_database = hash:/etc/postfix/aliases # this specifies where the virtual mailbox folders will be located virtual_mailbox_base = /var/spool/mail/vmail # this is for the mailbox location for each user virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf # and this is for aliases virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf # and this is for domain lookups virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf # this is how to connect to the domains (all virtual, but the option is there) # not used yet # transport_maps = mysql:/etc/postfix/mysql_transport.cf # Setup the uid/gid of the owner of the mail files - static:5000 allows virtual ones virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 inet_protocols=all # Cyrus SASL Support smtpd_sasl_path = smtpd smtpd_sasl_local_domain = xxxxx.com ####################### ## OLD CONFIGURATION ## ####################### #myorigin = /etc/mailname #mydestination = crazyinsanoman.xxxxx.com, localhost, localhost.localdomain #mailbox_size_limit = 0 #recipient_delimiter = + #html_directory = /usr/share/doc/postfix/html message_size_limit = 30720000 #virtual_alias_domains = ##virtual_alias_maps = hash:/etc/postfix/virtual #virtual_mailbox_base = /home/vmail ##luser_relay = webmaster #smtpd_sasl_type = dovecot #smtpd_sasl_path = private/auth smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes #smtpd_sasl_authenticated_header = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination #virtual_create_maildirsize = yes #virtual_maildir_extended = yes #proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $transport_maps $mynetworks $virtual_mailbox_limit_maps #virtual_transport = dovecot #dovecot_destination_recipient_limit = 1 Here is my master.cf: # # Postfix master process configuration file. For details on the format # of the file, see the master(5) manual page (command: "man 5 master"). # # Do not forget to execute "postfix reload" after editing this file. # # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - - - - smtpd submission inet n - - - - smtpd -o smtpd_tls_security_level=encrypt -o smtpd_sasl_auth_enable=yes -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #smtps inet n - - - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - - - - qmqpd pickup fifo n - - 60 1 pickup cleanup unix n - - - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - - 300 1 oqmgr tlsmgr unix - - - 1000? 1 tlsmgr rewrite unix - - - - - trivial-rewrite bounce unix - - - - 0 bounce defer unix - - - - 0 bounce trace unix - - - - 0 bounce verify unix - - - - 1 verify flush unix n - - 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap smtp unix - - - - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - - - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - - - - showq error unix - - - - - error retry unix - - - - - error discard unix - - - - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - - - - lmtp anvil unix - - - - 1 anvil scache unix - - - - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants. # # Many of the following services use the Postfix pipe(8) delivery # agent. See the pipe(8) man page for information about ${recipient} # and other message envelope options. # ==================================================================== # # maildrop. See the Postfix MAILDROP_README file for details. # Also specify in main.cf: maildrop_destination_recipient_limit=1 # maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/bin/maildrop -d ${recipient} # # ==================================================================== # # Recent Cyrus versions can use the existing "lmtp" master.cf entry. # # Specify in cyrus.conf: # lmtp cmd="lmtpd -a" listen="localhost:lmtp" proto=tcp4 # # Specify in main.cf one or more of the following: # mailbox_transport = lmtp:inet:localhost # virtual_transport = lmtp:inet:localhost # # ==================================================================== # # Cyrus 2.1.5 (Amos Gouaux) # Also specify in main.cf: cyrus_destination_recipient_limit=1 # cyrus unix - n n - - pipe user=cyrus argv=/cyrus/bin/deliver -e -r ${sender} -m ${extension} ${user} # # ==================================================================== # Old example of delivery via Cyrus. # #old-cyrus unix - n n - - pipe # flags=R user=cyrus argv=/cyrus/bin/deliver -e -m ${extension} ${user} # # ==================================================================== # # See the Postfix UUCP_README file for configuration details. # uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) # # Other external delivery methods. # ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=bsmtp argv=/usr/lib/bsmtp/bsmtp -t$nexthop -f$sender $recipient scalemail-backend unix - n n - 2 pipe flags=R user=scalemail argv=/usr/lib/scalemail/bin/scalemail-store ${nexthop} ${user} ${extension} mailman unix - n n - - pipe flags=FR user=list argv=/usr/lib/mailman/bin/postfix-to-mailman.py ${nexthop} ${user} #dovecot unix - n n - - pipe # flags=DRhu user=vmail:vmail argv=/usr/lib/dovecot/deliver -d ${recipient} Here is what I'm using for /etc/postfix/sasl/smtpd.conf log_level: 7 pwcheck_method: saslauthd pwcheck_method: auxprop mech_list: PLAIN LOGIN CRAM-MD5 DIGEST-MD5 allow_plaintext: true auxprop_plugin: mysql sql_hostnames: 127.0.0.1 sql_user: xxxxx sql_passwd: xxxxx sql_database: maildb sql_select: select crypt from users where id = '%u' As you can see I'm trying to use mysql as my authentication method. The password in 'users' is set through the 'ENCRYPT()' function. I also followed the methods found in http://www.jimmy.co.at/weblog/?p=52 in order to redo /var/spool/postfix/var/run/saslauthd as that seems to be a lot of people's problems, but that didn't help at all. Also, here is my /etc/default/saslauthd START=yes DESC="SASL Authentication Daemon" NAME="saslauthd" # Which authentication mechanisms should saslauthd use? (default: pam) # # Available options in this Debian package: # getpwent -- use the getpwent() library function # kerberos5 -- use Kerberos 5 # pam -- use PAM # rimap -- use a remote IMAP server # shadow -- use the local shadow password file # sasldb -- use the local sasldb database file # ldap -- use LDAP (configuration is in /etc/saslauthd.conf) # # Only one option may be used at a time. See the saslauthd man page # for more information. # # Example: MECHANISMS="pam" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" I had heard that potentially changing MECHANISM to MECHANISMS="mysql" but obviously that didn't help as is shown by the options listed above and also by trying it out anyway in case the documentation was outdated. So, I'm now at a loss... I have no idea where to go from here or what steps I need to do to get this working =/ Anyone have any ideas? EDIT: Here is the error that is coming from auth.log ... I don't know if this will help at all, but here you go: Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql auxprop plugin using mysql engine Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: begin transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from userPassword user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from cmusaslsecretPLAIN user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: commit transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1' Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: begin transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from userPassword user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin create statement from cmusaslsecretPLAIN user xxxxxx.com Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin doing query select crypt from users where id = '[email protected]'; Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: commit transaction Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin Parse the username [email protected] Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin try and connect to a host Aug 11 17:19:56 crazyinsanoman postfix/smtpd[9503]: sql plugin trying to open db 'maildb' on host '127.0.0.1'

    Read the article

  • Using pipes inside a class in C++

    - by Paul
    I'm trying to use this tutorial to make plots with Gnuplot in C++. However I will be using the pipe to Gnuplot from within a class, but then I run into some problems: I've got a header file where I declare all variables etc. I need to declare the pipe-variable here too, but how do I do that? I've tried doing it straight away, but it doesn't work: Logger.h: class Logger { FILE pipe; } Logger.cpp: Logger::Logger() { //Constructor *pipe = popen("gnuplot -persist","w"); } Gives the error Logger.cpp:28: error: no match for ‘operator=’ in ‘*((Logger*)this)->Logger::pipe = popen(((const char*)"gnuplot -persist"), ((const char*)"w"))’ Suggestions?

    Read the article

  • CommandBinding broken in inner Custom Control when nesting two Custom Controls of the same type.

    - by Fredrik Eriksson
    I've done a Custom Control in form of a GroupBox but with an extra header which purpose is to hold a button or a stackpanel with buttons at the other side. I've added the a Dependency Property to hold the extra header and I've connected the customized template. Everything works fine until I put one of these controls in another one. Now the wierd stuff begins(at least in my eyes xP), the command binding in the inner control simply isn't set. I tried to use Snoop to gather some data, the see if the inherits is broken and when I clicked on the buttons which isn't doing what I want it to, boom, breakpoint triggered. So in some wierd way the Command isn't set until something that I don't know what it is, happens, which snoops triggers. I've also tried to put the buttons in the regular Header property and that works fine, but not with my own made. I could just switch places with them to make it like I want but now I'm curious to know where the problem lies... Now I wonder, what can I've missed? The control class: public class TwoHeaderedGroupBox : GroupBox { static TwoHeaderedGroupBox() { DefaultStyleKeyProperty.OverrideMetadata(typeof(TwoHeaderedGroupBox), new FrameworkPropertyMetadata(typeof(TwoHeaderedGroupBox))); } public static DependencyProperty HeaderTwoProperty = DependencyProperty.Register("HeaderTwo", typeof(object), typeof(TwoHeaderedGroupBox), new FrameworkPropertyMetadata()); public object HeaderTwo { get { return (object)GetValue(HeaderTwoProperty); } set { SetValue(HeaderTwoProperty, value);} } } And here is the Template (which by the way is created by blend from the beginning): <ControlTemplate TargetType="{x:Type Controls:TwoHeaderedGroupBox}"> <Grid SnapsToDevicePixels="true"> <Grid.ColumnDefinitions> <ColumnDefinition Width="6"/> <ColumnDefinition Width="Auto"/> <ColumnDefinition Width="*"/> <ColumnDefinition Width="6"/> </Grid.ColumnDefinitions> <Grid.RowDefinitions> <RowDefinition Height="Auto"/> <RowDefinition Height="Auto"/> <RowDefinition Height="*"/> <RowDefinition Height="6"/> </Grid.RowDefinitions> <Border BorderBrush="Transparent" BorderThickness="{TemplateBinding BorderThickness}" Background="{TemplateBinding Background}" Grid.ColumnSpan="4" Grid.Column="0" CornerRadius="4" Grid.Row="1" Grid.RowSpan="3"/> <Border x:Name="Header" Grid.Column="1" Padding="3,1,3,0" Grid.Row="0" Grid.RowSpan="2" VerticalAlignment="Center"> <ContentControl Content="{TemplateBinding Header}" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}"/> </Border> <ContentPresenter Grid.ColumnSpan="2" Grid.Column="1" Margin="{TemplateBinding Padding}" Grid.Row="2" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}"/> <Border BorderBrush="White" BorderThickness="{TemplateBinding BorderThickness}" Grid.ColumnSpan="4" CornerRadius="4" Grid.Row="1" Grid.RowSpan="3"> <Border.OpacityMask> <MultiBinding ConverterParameter="7" Converter="{StaticResource BorderGapMaskConverter}"> <Binding ElementName="Header" Path="ActualWidth"/> <Binding Path="ActualWidth" RelativeSource="{RelativeSource Self}"/> <Binding Path="ActualHeight" RelativeSource="{RelativeSource Self}"/> </MultiBinding> </Border.OpacityMask> <Border BorderBrush="{TemplateBinding BorderBrush}" BorderThickness="{TemplateBinding BorderThickness}" CornerRadius="3"> <Border BorderBrush="White" BorderThickness="{TemplateBinding BorderThickness}" CornerRadius="2"/> </Border> </Border> <Border x:Name="HeaderTwo" Grid.Column="2" Padding="3,5,3,5" Grid.Row="0" Grid.RowSpan="2" HorizontalAlignment="Right"> <ContentControl Content="{TemplateBinding HeaderTwo}" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}" DataContext="{TemplateBinding DataContext}"/> </Border> </Grid> </ControlTemplate>

    Read the article

  • Popen is no able to process a command that runs in shell

    - by IceMan85
    Hello everybody, I have already read the previous questions posted on the same argument but I really haven't figured it out yet. I am trying to run a command that works without issues from the command line : xyz@klm:~/python-remoteWorkspace/PyLogParser/src:18:43ush -o PPP -p PRD -n log 'pwd' 6:43PM PPP:prd:lgsprdppp:/ama/log/PRD/ppp but when I do the same in python I always get errors : stringa = Popen(["ush -o PPP -p PRD -n log 'pwd'"], stdout=PIPE, stdin=PIPE).communicate()[0] Here the error. Traceback (most recent call last): File "getStatData.py", line 134, in retrieveListOfFiles(infoToRetList) File "getStatData.py", line 120, in retrieveListOfFiles stringa = Popen(["ush -o PPP -p PRD -n log 'pwd'"], stdout=PIPE, stdin=PIPE).communicate()[0] File "/opt/python-2.6-64/lib/python2.6/subprocess.py", line 595, in init errread, errwrite) File "/opt/python-2.6-64/lib/python2.6/subprocess.py", line 1092, in _execute_child raise child_exception OSError: [Errno 2] No such file or directory I've tried also different solutions like stringa = Popen(["ush", "-o", "PPP", "-p" "PRD", "-n", "log", '"pwd"'], stdout=PIPE, stdin=PIPE).communicate()[0] but nothing seems to work. I have also tried to put the absolute path to ush but nothing... Can somebody please explain me what am I doing wrong ? Thanks in advance, AM.

    Read the article

  • How to install 32-bit libraries using Debian Testing

    - by bgoodr
    Question: What is the way to determine, ahead of time and without doing a full install of 64-bit Debian Testing NETINST, when Debian Testing has 32-bit libraries available and fully working and installable so that the following command works without broken package errors?: apt-get install ia32-libs ia32-libs-gtk The errors that occur when 32-bit libraries are not available, still in some broken state, or whatever is broken are detailed below. I already have concluded that "Just install Stable" is my stop-gap measure for now, but I would like to know the answer to the above question so as to avoid a lengthy installation process only to run into these problems at the very end. Details: I downloaded the 64-bit Debian Testing netinst a couple of days ago. This was "Jessie" built 20131014-06:07 via http://tinyurl.com/lejpa. This is weekly testing build. Yes, I know I should expect problems, and I did. I managed to get it completely installed and was able to invoke into GNOME, but not get past the 32-bit library problem. The problems starts when I attempt to install the 32-bit libraries via: apt-get install ia32-libs ia32-libs-gtk that returns: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 but it is not installable ia32-libs-gtk : Depends: ia32-libs-i386 but it is not installable Depends: ia32-libs-gtk-i386 but it is not installable E: Unable to correct problems, you have held broken packages. I then found an old (2012 is old to me) answer at ia32-libs : Depends: ia32-libs-i386 but it is not installable and even tried what they suggested there which was dpkg --add-architecture i386 apt-get update After executing the above, I tried again but got: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 ia32-libs-gtk : Depends: ia32-libs-i386 E: Unable to correct problems, you have held broken packages. root@breath:~# And then tried this: root@breath:~# dpkg --get-selections | grep hold And that returned nothing. Not only is there broken packages, the system doesn't even know what packages are broken, so Debian Stable is my only solution I know of right now. Hence my question above.

    Read the article

  • Redirect output logs of javax.xml.ws and com.sun.xml.ws

    - by chrisnfoneur
    I am working on a SOAP based web service, with Sun's Metro. I am facing an annoying bug, each time I send a malformed SOAP object to my web service, sun's api spam the System.out with logs like this: javax.xml.ws.WebServiceException: com.sun.istack.XMLStreamException2: org.xml.sax.SAXParseException: cvc-complex-type.4: Attribute 'type' must appear on element 'object'. at com.sun.xml.ws.util.pipe.AbstractSchemaValidationTube.doProcess(AbstractSchemaValidationTube.java:206) at com.sun.xml.ws.util.pipe.AbstractSchemaValidationTube.processRequest(AbstractSchemaValidationTube.java:175) at com.sun.xml.ws.api.pipe.Fiber.__doRun(Fiber.java:595) at com.sun.xml.ws.api.pipe.Fiber._doRun(Fiber.java:554) at com.sun.xml.ws.api.pipe.Fiber.doRun(Fiber.java:539) at com.sun.xml.ws.api.pipe.Fiber.runSync(Fiber.java:436) at com.sun.xml.ws.server.WSEndpointImpl$2.process(WSEndpointImpl.java:243) at com.sun.xml.ws.transport.http.HttpAdapter$HttpToolkit.handle(HttpAdapter.java:444) at com.sun.xml.ws.transport.http.HttpAdapter.handle(HttpAdapter.java:244) at com.sun.xml.ws.transport.http.server.WSHttpHandler.handleExchange(WSHttpHandler.java:106) at com.sun.xml.ws.transport.http.server.WSHttpHandler.handle(WSHttpHandler.java:91) at com.sun.net.httpserver.Filter$Chain.doFilter(Filter.java:65) at sun.net.httpserver.AuthFilter.doFilter(AuthFilter.java:54) at com.sun.net.httpserver.Filter$Chain.doFilter(Filter.java:68) at sun.net.httpserver.ServerImpl$Exchange$LinkHandler.handle(ServerImpl.java:555) at com.sun.net.httpserver.Filter$Chain.doFilter(Filter.java:65) at sun.net.httpserver.ServerImpl$Exchange.run(ServerImpl.java:527) at sun.net.httpserver.ServerImpl$DefaultExecutor.execute(ServerImpl.java:119) at sun.net.httpserver.ServerImpl$Dispatcher.handle(ServerImpl.java:349) at sun.net.httpserver.ServerImpl$Dispatcher.run(ServerImpl.java:321) at java.lang.Thread.run(Thread.java:619) Caused by: com.sun.istack.XMLStreamException2: org.xml.sax.SAXParseException: cvc-complex-type.4: Attribute 'type' must appear on element 'object'. at com.sun.xml.ws.util.xml.StAXSource$1.parse(StAXSource.java:185) at com.sun.xml.ws.util.xml.StAXSource$1.parse(StAXSource.java:170) at org.apache.xerces.jaxp.validation.ValidatorHandlerImpl.validate(Unknown Source) at org.apache.xerces.jaxp.validation.ValidatorImpl.validate(Unknown Source) at javax.xml.validation.Validator.validate(Validator.java:127) at com.sun.xml.ws.util.pipe.AbstractSchemaValidationTube.doProcess(AbstractSchemaValidationTube.java:204) ... 20 more I would like to switch off this log or redirect it to my error/warn/debug.log files used by log4j. I tried to add a rule in my log4j.xml file : <category name="javax.xml.ws"> <priority value="error" /> </category> It didn't worked. So I tried the following trick: java.util.logging.Logger.getLogger("javax.xml.ws.WebServiceException").setLevel( java.util.logging.Level.OFF); it didn't worked neither. Any ideas ? It is not a big issue but it makes my catalina.log getting bigger & bigger and it's not the appropriate place for this kind of log. Chris

    Read the article

  • Asynchronous subprocess on Windows

    - by Stigma
    First of all, the overall problem I am solving is a bit more complicated than I am showing here, so please do not tell me 'use threads with blocking' as it would not solve my actual situation without a fair, FAIR bit of rewriting and refactoring. I have several applications which are not mine to modify, which take data from stdin and poop it out on stdout after doing their magic. My task is to chain several of these programs. Problem is, sometimes they choke, and as such I need to track their progress which is outputted on STDERR. pA = subprocess.Popen(CommandA, shell=False, stdout=subprocess.PIPE, stderr=subprocess.PIPE) # ... some more processes make up the chain, but that is irrelevant to the problem pB = subprocess.Popen(CommandB, shell=False, stdout=subprocess.PIPE, stderr=subprocess.PIPE, stdin=pA.stdout ) Now, reading directly through pA.stdout.readline() and pB.stdout.readline(), or the plain read() functions, is a blocking matter. Since different applications output in different paces and different formats, blocking is not an option. (And as I wrote above, threading is not an option unless at a last, last resort.) pA.communicate() is deadlock safe, but since I need the information live, that is not an option either. Thus google brought me to this asynchronous subprocess snippet on ActiveState. All good at first, until I implement it. Comparing the cmd.exe output of pA.exe | pB.exe, ignoring the fact both output to the same window making for a mess, I see very instantaneous updates. However, I implement the same thing using the above snippet and the read_some() function declared there, and it takes over 10 seconds to notify updates of a single pipe. But when it does, it has updates leading all the way upto 40% progress, for example. Thus I do some more research, and see numerous subjects concerning PeekNamedPipe, anonymous handles, and returning 0 bytes available even though there is information available in the pipe. As the subject has proven quite a bit beyond my expertise to fix or code around, I come to Stack Overflow to look for guidance. :) My platform is W7 64-bit with Python 2.6, the applications are 32-bit in case it matters, and compatibility with Unix is not a concern. I can even deal with a full ctypes or pywin32 solution that subverts subprocess entirely if it is the only solution, as long as I can read from every stderr pipe asynchronously with immediate performance and no deadlocks. :)

    Read the article

  • s3cmd fails too many times

    - by alfish
    It used to be my favorite backup transport agent but now I frequently get this result from s3cmd on the very same Ubuntu server/network: root@server:/home/backups# s3cmd put bkup.tgz s3://mybucket/ bkup.tgz -> s3://mybucket/bkup.tgz [1 of 1] 36864 of 2711541519 0% in 1s 20.95 kB/s failed WARNING: Upload failed: /bkup.tgz ([Errno 32] Broken pipe) WARNING: Retrying on lower speed (throttle=0.00) WARNING: Waiting 3 sec... bkup.tgz -> s3://mybucket/bkup.tgz [1 of 1] 36864 of 2711541519 0% in 1s 23.96 kB/s failed WARNING: Upload failed: /bkup.tgz ([Errno 32] Broken pipe) WARNING: Retrying on lower speed (throttle=0.01) WARNING: Waiting 6 sec... bkup.tgz -> s3://mybucket/bkup.tgz [1 of 1] 28672 of 2711541519 0% in 1s 18.71 kB/s failed WARNING: Upload failed: /bkup.tgz ([Errno 32] Broken pipe) WARNING: Retrying on lower speed (throttle=0.05) WARNING: Waiting 9 sec... bkup.tgz -> s3://mybucket/bkup.tgz [1 of 1] 28672 of 2711541519 0% in 1s 18.86 kB/s failed WARNING: Upload failed: /bkup.tgz ([Errno 32] Broken pipe) WARNING: Retrying on lower speed (throttle=0.25) WARNING: Waiting 12 sec... bkup.tgz -> s3://mybucket/bkup.tgz [1 of 1] 28672 of 2711541519 0% in 1s 15.79 kB/s failed WARNING: Upload failed: /bkup.tgz ([Errno 32] Broken pipe) WARNING: Retrying on lower speed (throttle=1.25) WARNING: Waiting 15 sec... bkup.tgz -> s3://mybucket/bkup.tgz [1 of 1] 12288 of 2711541519 0% in 2s 4.78 kB/s failed ERROR: Upload of 'bkup.tgz' failed too many times. Skipping that file. This happens even for files as small as 100MB, so I suppose it's not a size issue. It also happens when I use put with --acl-private flag (s3cmd version 1.0.1) I appreciate if you suggest some solution or a lightweight alternative to s3cmd. Thanks

    Read the article

  • External routing for local interfaces in a virtualized network

    - by Arkaitz Jimenez
    Current setup: br0| |-- tun10 -pipe-tun0(192.240.240.1) |-- tun11 -pipe-tun1(192.240.240.2) |-- tun12 -pipe-tun2(192.240.240.3) The pipe program is a custom program that forwards data back2back between two tun interfaces. The idea is puting 2 programs in .2 and .3 while keeping .1 as the local interface in the current machine. The main problem is that I want to route packets to .2 and to .3 through .1 and br0, but as they are local interfaces, the kernel ignores any routing instruction, it just delivers the packet to the proper interface. Tried iptables, but the nat table doesn't even see ping packets to those ifaces. A "ping 192.240.240.2" delivers a icmp packet with source and dest .2 to tun1, ideally it should deliver a source .1 dest .2 at tun1 through tun0-br0-tun1 Any hint? Here the output of some commands: Output

    Read the article

  • Setting up Relays in Windows

    - by Auditor
    I'm trying to setup a pivoting relay with netcat on Windows, replicating a scenario easily possible by using pipes in Linux. Assume machine A can route to machine B and machine B can route to machine C. If machine A needs to route to machine C, we can setup a relay on machine B which can pivot data back and forth for us using command redirectors and spl filetype pipe. Assume: machine C has nc -nlvp 3306 -e cmd.exe machine A has nc -nlvp 80 IF machine B was Linux we could have done mkfifo pipe nc -nv 127.0.0.1 80 0<pipe | nc -nv 127.0.0.1 3306 1>pipe so on machine B if we do nc -nv 127.0.0.1 80 0<&4 | nc -nv 127.0.0.1 3306 1>&4 Per this site, I should be able to achieve what I can with Linux, but unfortunately it is not working.

    Read the article

  • JAX-WS, webservices (Spring) issue

    - by vinay
    Hi All, I have written web services and configured with spring framework but I am getting exception when invoking services. Exceptions stack trace are given below - com.sun.xml.ws.server.sei.EndpointMethodHandler invoke SEVERE: object is not an instance of declaring class java.lang.IllegalArgumentException: object is not an instance of declaring class at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl. java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces sorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.jvnet.jax_ws_commons.spring.SpringService$1$1.invoke(SpringServic e.java:185) at com.sun.xml.ws.server.InvokerTube$2.invoke(InvokerTube.java:152) at com.sun.xml.ws.server.sei.EndpointMethodHandler.invoke(EndpointMethod Handler.java:264) at com.sun.xml.ws.server.sei.SEIInvokerTube.processRequest(SEIInvokerTub e.java:93) at com.sun.xml.ws.api.pipe.Fiber.__doRun(Fiber.java:604) at com.sun.xml.ws.api.pipe.Fiber._doRun(Fiber.java:563) at com.sun.xml.ws.api.pipe.Fiber.doRun(Fiber.java:548) at com.sun.xml.ws.api.pipe.Fiber.runSync(Fiber.java:445) at com.sun.xml.ws.server.WSEndpointImpl$2.process(WSEndpointImpl.java:27 5) at com.sun.xml.ws.transport.http.HttpAdapter$HttpToolkit.handle(HttpAdap ter.java:454) at com.sun.xml.ws.transport.http.HttpAdapter.handle(HttpAdapter.java:250 ) at com.sun.xml.ws.transport.http.servlet.ServletAdapter.handle(ServletAd apter.java:140) at com.sun.xml.ws.transport.http.servlet.WSServletDelegate.doGet(WSServl etDelegate.java:129) at com.sun.xml.ws.transport.http.servlet.WSServletDelegate.doPost(WSServ letDelegate.java:160) at com.sun.xml.ws.transport.http.servlet.WSSpringServlet.doPost(WSSpring Servlet.java:52) at javax.servlet.http.HttpServlet.service(HttpServlet.java:727) at javax.servlet.http.HttpServlet.service(HttpServlet.java:820) at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run (StubSecurityHelper.java:227) at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecuri tyHelper.java:125) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.jav a:292) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.jav a:175) at weblogic.servlet.internal.WebAppServletContext$ServletInvocationActio n.run(WebAppServletContext.java:3594) at weblogic.security.acl.internal.AuthenticatedSubject.doAs(Authenticate dSubject.java:321) at weblogic.security.service.SecurityManager.runAs(SecurityManager.java: 121) at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppS ervletContext.java:2202) at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletC ontext.java:2108) at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.j ava:1432) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201) at weblogic.work.ExecuteThread.run(ExecuteThread.java:173) Mar 31, 2010 3:47:20 PM com.sun.xml.ws.server.sei.EndpointMethodHandler invoke SEVERE: object is not an instance of declaring class java.lang.IllegalArgumentException: object is not an instance of declaring class at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl. java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces sorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.jvnet.jax_ws_commons.spring.SpringService$1$1.invoke(SpringServic e.java:185) at com.sun.xml.ws.server.InvokerTube$2.invoke(InvokerTube.java:152) at com.sun.xml.ws.server.sei.EndpointMethodHandler.invoke(EndpointMethod Handler.java:264) at com.sun.xml.ws.server.sei.SEIInvokerTube.processRequest(SEIInvokerTub e.java:93) at com.sun.xml.ws.api.pipe.Fiber.__doRun(Fiber.java:604) at com.sun.xml.ws.api.pipe.Fiber._doRun(Fiber.java:563) at com.sun.xml.ws.api.pipe.Fiber.doRun(Fiber.java:548) at com.sun.xml.ws.api.pipe.Fiber.runSync(Fiber.java:445) at com.sun.xml.ws.server.WSEndpointImpl$2.process(WSEndpointImpl.java:27 5) at com.sun.xml.ws.transport.http.HttpAdapter$HttpToolkit.handle(HttpAdap ter.java:454) at com.sun.xml.ws.transport.http.HttpAdapter.handle(HttpAdapter.java:250 ) at com.sun.xml.ws.transport.http.servlet.ServletAdapter.handle(ServletAd apter.java:140) at com.sun.xml.ws.transport.http.servlet.WSServletDelegate.doGet(WSServl etDelegate.java:129) at com.sun.xml.ws.transport.http.servlet.WSServletDelegate.doPost(WSServ letDelegate.java:160) at com.sun.xml.ws.transport.http.servlet.WSSpringServlet.doPost(WSSpring Servlet.java:52) at javax.servlet.http.HttpServlet.service(HttpServlet.java:727) at javax.servlet.http.HttpServlet.service(HttpServlet.java:820) at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run (StubSecurityHelper.java:227) at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecuri tyHelper.java:125) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.jav a:292) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.jav a:175) at weblogic.servlet.internal.WebAppServletContext$ServletInvocationActio n.run(WebAppServletContext.java:3594) at weblogic.security.acl.internal.AuthenticatedSubject.doAs(Authenticate dSubject.java:321) at weblogic.security.service.SecurityManager.runAs(SecurityManager.java: 121) at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppS ervletContext.java:2202) at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletC ontext.java:2108) at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.j ava:1432) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201) at weblogic.work.ExecuteThread.run(ExecuteThread.java:173) i am testing our services using SOAP UI and getting above mentioed exception. I think some how the object creation from the xml is not acceptable to webservices I am confused what is happening

    Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >