Search Results

Search found 4186 results on 168 pages for 'ember router'.

Page 30/168 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• How can I configure a Linksys EA4500 + usb printer for network printing (without connect cloud)

  - by Larry Kyrala

  The documentation and classic firmware (2.0.37) for Cisco's Linksys EA4500 is a bit sparse on setup details. It says I can connect a USB-printer, but then goes on to try to sell "Connect Cloud" remote management software. I don't want that. I just want to know how to set this up with the existing advanced firmware. Is it possible? AFAIK, to setup a IPP or LDP printer, there is usually some kind of queue configuration on the server (i.e. the ea4500 in this case), but I can't find it in the firmware. I also have been unable to find any existing protocols from win7 or mac osx. (windows network share, IPP/LDP etc.) I'm curious if I need to have the "Storage" accounts active and connect to my router either via the local IP or router name. There's a lot of unknowns here; it would help to know how this particular router actually works.

  Read the article

• 2 routers, both DHCP, no IP assigned

  - by piobyz

  I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

  Read the article

• "custom" routers for VPN - useful or waste of money?

  - by Andrew Heath

  I use VPN in China and my current service contract expires soon so I was checking what sort of plans are out there now. I found that Witopia offers a "Cloak Box", what appears to be a Linksys wireless router with allegedly hacked/custom firmware to support VPN. Aside from allowing multiple computers to share one VPN connection, is there anything else at work here to justify that price when most new routers are $100 or less these days? Or is this something targeted towards the cd-rom cupholder crowd? And yes, I've contacted them, but haven't heard back yet... EDIT I've heard back from the company - here are the details if anyone else is interested: the router is a Linksys WRT54GL running TomatoVPN custom firmware the hardware waranty is one (1) year, from Linksys/Cisco the VPN is hard-set, so any device connected to the router MUST use the VPN (Witopia blocks torrents) I've decided it's not for me, but hopefully this information will prove useful to others.

  Read the article

• Internet connection slower than network connection speed

  - by Mike Pateras

  I've got a computer connected to a wireless router on a different floor. When I look at the network connection, I'm told the signal strength is low, and that I've got a connection of about 26mbps (often higher). However, my internet connection on that machine is very slow. Speedtests show it at about 1-2mbps, and it really shows when loading pages and video. I have fiber optic internet access, and the machine that's connected to the router/modem via cable gets the 20mbps on speed tests, and is extremely fast in every day use. My question is, is the advertised 26mbps+ connection speed perhaps inaccurate, and that my wireless bandwidth is the likely bottleneck here? Or is the signal strength what's key here? And what might I do about this? Power cycling the router helped a bit, a speed test went as high as 6mbps after doing that.

  Read the article

• VPN only connects once and then fails

  - by Toby Allen

  I have a VPN connection setup to my office from home, it works great except for one thing. Once I connect and then disconnect the next time I go to connect to the vpn it hangs on verifying your username and password. No matter how many times I try. Once I restart my router it works again. My router is a belkin, the router on the other end is a Draytek. Any ideas? Is there a cache somewhere that needs to be reset, a setting?

  Read the article

• Two Routers, Two Internet (1 Open, 1 PPTP) - Routing?

  - by SomeUser

  Hi there, I'm trying to setup two routers - one to route specific sites to a always-on PPTP VPN connection, the other for open internet access w/ firewall. First router is connected to Internet w/ built-in firewall. Second router is connected to a PPTP VPN connection. I was going to connect a wire between the routers and would like some insight on how to get both groups of systems (connected to each router) to talk between automatically. Even better would be to setup one gateway for certain sites and another for general Internet. The other option is to default all sites to the net and shoot others to the gateway or vice versa... Any insight so I can get a better grasp of this? Thanks!

  Read the article

• Routing from the DMZ to the interior network only

  - by Allan

  I have a home network connected to Verizon's FIOS service. Verizon's ActionTec router is connected to the ONT via coax to establish the MOCA network. My DD-WRT router's WAN port is connected to one of the ActionTec's LAN ports. The DD-WRT router is configured with a static IP address and assigned to the DMZ (this is done so I only have to configure port forwarding once). My issue is that this does not allow computers connected to the DD-WRT to serve streaming audio/video to the MOCA network using Verizon's Media Manager. I know that Media Manager uses ports 18001, 5050, and 5060, but I don't know how to forward those ports so that they are only available to the ActionTec's network and not the rest of the internet.

  Read the article

• Usage of two Routers on LAN

  - by brusilva

  I've currently own a Linksys E4200 and a Thomson 546v6. Because I have an IPTV service I must set the Thomson as the main router connected to the phone line so that I can distribute the video signal for 2 specific ports and the other two for LAN Access. The problem is that the Thomson doesn't like port forwards, it usually doesnt work and since I have a good router (linksys) currently only working as Access Point I would like to use it as a router itself. I don't want to do a NAT beyond NAT so my question is should I connect the E4200 and to thomson and set the E4200 as a DMZ machine and then control all trafic on the E4200 itself or is there any other option that could suit my needs better?

  Read the article

• IP Connflict on network

  - by PSU_Kardi

  I keep getting an IP conflict on my home network and can't figure out why. I'm running a Belkin-N wireless router that has an Ethernet connection to my 360 and a wireless connection running to my laptop. It's WPA2 encryption and I have a nice password on my router consisting of letters , numbers and special characters. But for some reason I keep getting IP conflicts at night time...By the time I look into the problem I don't see anyone else on the network. Is my router giving me false positives?

  Read the article

• Virtual firewall to protect hypervisor

  - by manutenfruits

  I am running an Ubuntu Server 12.10 as a single host connected to a NATed router connected using PPPoE to a optical fiber modem. This server is meant to be accessed from the Internet, but also to be used from the LAN as a SVN, MySQL and what not... The issue is that the router is not customizable enough to serve, so I was thinking about creating a virtual pfSense firewall using KVM inside of the server itself, removing the need of the router. Is this possible? Can the host ignore and block all traffic coming to itself, but not for the firewall? I am aware this is not the most desirable environment, I accept suggestions based on budget!

  Read the article

• DIR-615 lose internet connection after 3 minutes

  - by Sirber

  I got a new DLink DIR-615 routeur. DSL model connects fine. Connected PCs connects to the internet fine (wireless, wired) fine too. After ~3 minutes, connected PCs cannot go to the internet. Web pages goes timeout, sometimes google talk stays on (working). From the router admin page, pings works correctly (on google.ca), so the connection is active. pc -- routeur -- internet: fail pc -- router: ok router -- internet: ok could it be firewall related? I've read there's a SPI firewall enabled.

  Read the article

• DIR-615 lose internet connection after 3 minutes

  - by user31375

  I got a new DLink DIR-615 routeur. DSL model connects fine. Connected PCs connects to the internet fine (wireless, wired) fine too. After ~3 minutes, connected PCs cannot go to the internet. Web pages goes timeout, sometimes google talk stays on (working). From the router admin page, pings works correctly (on google.ca), so the connection is active. pc -- routeur -- internet: fail pc -- router: ok router -- internet: ok could it be firewall related? I've read there's a SPI firewall enabled.

  Read the article

• Laptops trying to connect via wireless? Only able to connect only via wired connection

  - by Chris J. Lee

  It seems that all the wireless laptops in the office have disconnected and are unable to reconnect to the wifi after a terrible storm caused some power interruptions. Troubleshooting actions Verify wireless broadcasting is up With each laptop i ended up flushing their dns cache on Win 7 (ipconfig /flush ) Performed an ipconfig /all to see what the new ip is Made sure password was correct Reset the router (multiple times) restarted each laptop. Tried connecting wirelessly Am i missing some small detail ? Network information The router is a linksys/cisco WRVS4400N router. Supports a lot of fancy features i don't know how to use. We have 3 static ip's the conference room computer, the wireless printer, my computer Mostly windows machines, we have 3 mac users

  Read the article

• Computer never connects to the internet automatically on startup?

  - by RawR Crew

  I have my Windows Vista laptop connected directly to the router via an ethernet cable, and every time I switch the computer on, the computer cannot connect to the internet. It comes up as limited or no connectivity, I am assuming because it has not been assigned an IP address by the router - not too sure if this is right. The problem is usually fixed either by performing a repair through the networking control panel or removing and re-inserting the ethernet cable. It will also connect without doing any of these if the computer is left idle for about 20 minutes. It will connect fine wirelessly without the need for any of this, however I would prefer to connect via the cable. Any ideas how I can fix this? I have replaced the ethernet cable and router already (identical model) but these haven't helped. Thanks for any help on this.

  Read the article

• Wi-fi signal with keeping the internet cable

  - by daGrevis

  So the situation is that I have Ethernet cable which provides internet to my computer. Thing I want is to have wi-fi connection in my house and Ethernet cable (like I have before) to use for my PC. I will use wi-fi for my laptop and mobile phone. I think I need router for that and I'm looking at Asus RT-N16 (suggested in Coding Horror) for it, but I am not sure. Is it the right thing for me and I will be able to get wi-fi signal and keep the Ethernet cable? I guess the system will be that current cable goes into router, router provides wi-fi signal and gives back new cable... or something like that. Thanks in any advice! And sorry if topic isn't in right site.

  Read the article

• Can't ping IPs for devices not part of Windows Domain

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The DNS server is on a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. All machines either have a fixed or DHCP allocated IP on the 192.168.0.* subnet. How do I configure the DNS server or the Windows Domain so that Windows machines can see the iPhones?

  Read the article

• Troubleshooting a slow database server with no load

  - by user1721724

  I'm getting ready to soft launch my website and I've run into some problems with what I think is being caused by my MySQL database running on Fedora. All websites run fine, just as I'd expect, but any pages that establish a database connection hang until the connection is established, and then bang, the site loads as it should. Ex. My landing page (http://www.thrusong.com) doesn't make a database connection and loads quickly. User profile pages (http://www.thrusong.com/john) make a database connection and load slowly, even though most of the data comes from memcached and the database currently has no load on it. This problem just came up yesterday when my router died and I began using my Pace 2Wire modem with built-in router. Before, my old router was set to handle everything. My ISP says the settings in the modem are correct. Any ideas? Thanks in advance.

  Read the article

• Wireless is connected but no internet when PC Turns on

  - by mhesabi

  I have a PC that is connected to ADSL Modem router (linksys WAG54g2) directly via Ethernet cable And a laptop and also other devices such as another laptops and smarth phones. However when I turn On the PC or turn it off, some strange problem happens. My wireless network seems connected on laptop but there is no internet activity and can't open a webpage until I turn router off and on again manually. (other devices including the PC itself can't use the internet either) My router configured this way: Encapsulation: RFC 2516 PPPoE Multiplexing: LLC DHCP Server: Enabled and network sharing center IPv4 configuration is obtain IP address automatically How Can I fix this issue?

  Read the article

• Extend university wifi network [migrated]

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want? Thank you all

  Read the article

• My Laptop (HP/Compaq 2510p) running ubuntu 10.04 LTS keeps losing the WLAN connection.

  - by Ernelli

  I am using Wicd and can successfully connect to my ADSL router (Thomson TG 787) using WPA PSK. But with regular interval I lose the ability to connect to Internet. I can ping the GW and can actually ping servers on the Internet but not connect to them using HTTP (Tested with both Firefox and wget). I would suspect the router unless for the fact that the problem does not show up when running Windows XP on the same computer and also, when the problem arises, a simple disconnect/connect in Wicd solves the problem, which does not involve the router (Except for the DHCP request). I have searched Ubuntu forums without luck, most problems described relate to specific network drivers or other problems. Does anyone have the same experience with Linux/Ubuntu and WLAN?

  Read the article

• Newly installed DIR-615 - how to connect to the wireless?

  - by JK123

  I've just installed a D-Link DIR 615, but can't figure out how to connect to the wireless.. When I double click my wireless icon in the tray, it does show the new network. Its starts the "WiFi protected setup wizard" and the first thing it asks for is the "Device Ownership Password". I have no idea what that is - I've tried the PIN and the router password. On the next page it says: SSID: _(name)__ Security type: _wpa2 personal aes ccmp_ Password: _some long key that is not what I entered during router setup_ I change the key to the one I created when setting up the router. I've also tried leaving the key as it is shown in the dialog. But it does not connect either way. All it says is "Configuration failed" So how do I connect to the new wireless network??

  Read the article

• Extend university wifi network

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want?

  Read the article

• Use 2 wireless adapters to connect to 2 WIFI networks (local and internet) simultaneously?

  - by Mouad

  On my HP Compaq 6710b there's an internal WIFI network adapter. Attached to the same laptop there's also an external USB Alfa WIFI adapter. I live near campus and can pick it's WIFI signal. The problem is that when I am connected to the Internet Wifi using the internal adapter, and then connect to the home (non-internet) Wifi network's router, I lose the connection to the internet (it stays connected, but there's no actual connection). So how can I use the two adapters to connect to both networks successfully ? The router is Belkin N150 Enhanced Router Model F6D4230-4 V1 The external adapter is: ALFA AWUS 036NHR

  Read the article

• How do I set up a proxy server for home with bandwidth control, download limit options?

  - by Quakeboy

  3 room mates share a single 2 Mbps connection. Have a 40GB per month download limit beyond which speed drops to 256Kbps which is annoying. One of the roommates abuses the connection by downloading beyond his quota limit. I have a Netgear WNR1000v2 Wireless router + ADSL Modem to connect to the internet. We all access internet via Wireless router which connects to ADSL Modem. I need a free proxy solution which can help me set 40GB / 3 (13 GB) limit for each person (every person has 2 devices - a PC and a phone with Wifi) Uniform Bandwidth control - when 2 people browse the internet they should get 1 Mbps each, and when 3 people access, they should get 2Mbps divided by 3. After each person crosses their monthly download limit, they should be able to access the internet with 256Kbps speed only or lesser. Can I have a custom firmware on my wireless router do this (or) Do I need a proxy server ? Please point me to any relevant tutorials (for example with Squid).

  Read the article

• Netgear routers don't allow you to disable wireless admin??

  - by MousePad

  I just bought a new router, the NetGear WGR614. Nowhere in the settings can you disable the ability to administrate the router from a wireless connection, which opens it up to brute force attacks from outside the building. Furthermore, it doesn't require a direct connection to the router to admin either, you can admin it while you're connected to the Internet. This means it opens itself to the possibility of an attack from within the network. This is unbelievable to me. What am I missing? Can this be possible?

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >