Search Results

Search found 738 results on 30 pages for 'scoped ptr'.

Page 30/30 | < Previous Page | 26 27 28 29 30 

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• Windows Azure: Backup Services Release, Hyper-V Recovery Manager, VM Enhancements, Enhanced Enterprise Management Support

  - by ScottGu

  This morning we released a huge set of updates to Windows Azure.  These new capabilities include: Backup Services: General Availability of Windows Azure Backup Services Hyper-V Recovery Manager: Public preview of Windows Azure Hyper-V Recovery Manager Virtual Machines: Delete Attached Disks, Availability Set Warnings, SQL AlwaysOn Configuration Active Directory: Securely manage hundreds of SaaS applications Enterprise Management: Use Active Directory to Better Manage Windows Azure Windows Azure SDK 2.2: A massive update of our SDK + Visual Studio tooling support All of these improvements are now available to use immediately.  Below are more details about them. Backup Service: General Availability Release of Windows Azure Backup Today we are releasing Windows Azure Backup Service as a general availability service.  This release is now live in production, backed by an enterprise SLA, supported by Microsoft Support, and is ready to use for production scenarios. Windows Azure Backup is a cloud based backup solution for Windows Server which allows files and folders to be backed up and recovered from the cloud, and provides off-site protection against data loss. The service provides IT administrators and developers with the option to back up and protect critical data in an easily recoverable way from any location with no upfront hardware cost. Windows Azure Backup is built on the Windows Azure platform and uses Windows Azure blob storage for storing customer data. Windows Server uses the downloadable Windows Azure Backup Agent to transfer file and folder data securely and efficiently to the Windows Azure Backup Service. Along with providing cloud backup for Windows Server, Windows Azure Backup Service also provides capability to backup data from System Center Data Protection Manager and Windows Server Essentials, to the cloud. All data is encrypted onsite before it is sent to the cloud, and customers retain and manage the encryption key (meaning the data is stored entirely secured and can’t be decrypted by anyone but yourself). Getting Started To get started with the Windows Azure Backup Service, create a new Backup Vault within the Windows Azure Management Portal.  Click New->Data Services->Recovery Services->Backup Vault to do this: Once the backup vault is created you’ll be presented with a simple tutorial that will help guide you on how to register your Windows Servers with it: Once the servers you want to backup are registered, you can use the appropriate local management interface (such as the Microsoft Management Console snap-in, System Center Data Protection Manager Console, or Windows Server Essentials Dashboard) to configure the scheduled backups and to optionally initiate recoveries. You can follow these tutorials to learn more about how to do this: Tutorial: Schedule Backups Using the Windows Azure Backup Agent This tutorial helps you with setting up a backup schedule for your registered Windows Servers. Additionally, it also explains how to use Windows PowerShell cmdlets to set up a custom backup schedule. Tutorial: Recover Files and Folders Using the Windows Azure Backup Agent This tutorial helps you with recovering data from a backup. Additionally, it also explains how to use Windows PowerShell cmdlets to do the same tasks. Below are some of the key benefits the Windows Azure Backup Service provides: Simple configuration and management. Windows Azure Backup Service integrates with the familiar Windows Server Backup utility in Windows Server, the Data Protection Manager component in System Center and Windows Server Essentials, in order to provide a seamless backup and recovery experience to a local disk, or to the cloud. Block level incremental backups. The Windows Azure Backup Agent performs incremental backups by tracking file and block level changes and only transferring the changed blocks, hence reducing the storage and bandwidth utilization. Different point-in-time versions of the backups use storage efficiently by only storing the changes blocks between these versions. Data compression, encryption and throttling. The Windows Azure Backup Agent ensures that data is compressed and encrypted on the server before being sent to the Windows Azure Backup Service over the network. As a result, the Windows Azure Backup Service only stores encrypted data in the cloud storage. The encryption key is not available to the Windows Azure Backup Service, and as a result the data is never decrypted in the service. Also, users can setup throttling and configure how the Windows Azure Backup service utilizes the network bandwidth when backing up or restoring information. Data integrity is verified in the cloud. In addition to the secure backups, the backed up data is also automatically checked for integrity once the backup is done. As a result, any corruptions which may arise due to data transfer can be easily identified and are fixed automatically. Configurable retention policies for storing data in the cloud. The Windows Azure Backup Service accepts and implements retention policies to recycle backups that exceed the desired retention range, thereby meeting business policies and managing backup costs. Hyper-V Recovery Manager: Now Available in Public Preview I’m excited to also announce the public preview of a new Windows Azure Service – the Windows Azure Hyper-V Recovery Manager (HRM). Windows Azure Hyper-V Recovery Manager helps protect your business critical services by coordinating the replication and recovery of System Center Virtual Machine Manager 2012 SP1 and System Center Virtual Machine Manager 2012 R2 private clouds at a secondary location. With automated protection, asynchronous ongoing replication, and orderly recovery, the Hyper-V Recovery Manager service can help you implement Disaster Recovery and restore important services accurately, consistently, and with minimal downtime. Application data in an Hyper-V Recovery Manager scenarios always travels on your on-premise replication channel. Only metadata (such as names of logical clouds, virtual machines, networks etc.) that is needed for orchestration is sent to Azure. All traffic sent to/from Azure is encrypted. You can begin using Windows Azure Hyper-V Recovery today by clicking New->Data Services->Recovery Services->Hyper-V Recovery Manager within the Windows Azure Management Portal.  You can read more about Windows Azure Hyper-V Recovery Manager in Brad Anderson’s 9-part series, Transform the datacenter. To learn more about setting up Hyper-V Recovery Manager follow our detailed step-by-step guide. Virtual Machines: Delete Attached Disks, Availability Set Warnings, SQL AlwaysOn Today’s Windows Azure release includes a number of nice updates to Windows Azure Virtual Machines.  These improvements include: Ability to Delete both VM Instances + Attached Disks in One Operation Prior to today’s release, when you deleted VMs within Windows Azure we would delete the VM instance – but not delete the drives attached to the VM.  You had to manually delete these yourself from the storage account.  With today’s update we’ve added a convenience option that now allows you to either retain or delete the attached disks when you delete the VM:   We’ve also added the ability to delete a cloud service, its deployments, and its role instances with a single action. This can either be a cloud service that has production and staging deployments with web and worker roles, or a cloud service that contains virtual machines.  To do this, simply select the Cloud Service within the Windows Azure Management Portal and click the “Delete” button: Warnings on Availability Sets with Only One Virtual Machine In Them One of the nice features that Windows Azure Virtual Machines supports is the concept of “Availability Sets”.  An “availability set” allows you to define a tier/role (e.g. webfrontends, databaseservers, etc) that you can map Virtual Machines into – and when you do this Windows Azure separates them across fault domains and ensures that at least one of them is always available during servicing operations.  This enables you to deploy applications in a high availability way. One issue we’ve seen some customers run into is where they define an availability set, but then forget to map more than one VM into it (which defeats the purpose of having an availability set).  With today’s release we now display a warning in the Windows Azure Management Portal if you have only one virtual machine deployed in an availability set to help highlight this: You can learn more about configuring the availability of your virtual machines here. Configuring SQL Server Always On SQL Server Always On is a great feature that you can use with Windows Azure to enable high availability and DR scenarios with SQL Server. Today’s Windows Azure release makes it even easier to configure SQL Server Always On by enabling “Direct Server Return” endpoints to be configured and managed within the Windows Azure Management Portal.  Previously, setting this up required using PowerShell to complete the endpoint configuration.  Starting today you can enable this simply by checking the “Direct Server Return” checkbox: You can learn more about how to use direct server return for SQL Server AlwaysOn availability groups here. Active Directory: Application Access Enhancements This summer we released our initial preview of our Application Access Enhancements for Windows Azure Active Directory.  This service enables you to securely implement single-sign-on (SSO) support against SaaS applications (including Office 365, SalesForce, Workday, Box, Google Apps, GitHub, etc) as well as LOB based applications (including ones built with the new Windows Azure AD support we shipped last week with ASP.NET and VS 2013). Since the initial preview we’ve enhanced our SAML federation capabilities, integrated our new password vaulting system, and shipped multi-factor authentication support. We've also turned on our outbound identity provisioning system and have it working with hundreds of additional SaaS Applications: Earlier this month we published an update on dates and pricing for when the service will be released in general availability form.  In this blog post we announced our intention to release the service in general availability form by the end of the year.  We also announced that the below features would be available in a free tier with it: SSO to every SaaS app we integrate with – Users can Single Sign On to any app we are integrated with at no charge. This includes all the top SAAS Apps and every app in our application gallery whether they use federation or password vaulting. Application access assignment and removal – IT Admins can assign access privileges to web applications to the users in their active directory assuring that every employee has access to the SAAS Apps they need. And when a user leaves the company or changes jobs, the admin can just as easily remove their access privileges assuring data security and minimizing IP loss User provisioning (and de-provisioning) – IT admins will be able to automatically provision users in 3rd party SaaS applications like Box, Salesforce.com, GoToMeeting, DropBox and others. We are working with key partners in the ecosystem to establish these connections, meaning you no longer have to continually update user records in multiple systems. Security and auditing reports – Security is a key priority for us. With the free version of these enhancements you'll get access to our standard set of access reports giving you visibility into which users are using which applications, when they were using them and where they are using them from. In addition, we'll alert you to un-usual usage patterns for instance when a user logs in from multiple locations at the same time. Our Application Access Panel – Users are logging in from every type of devices including Windows, iOS, & Android. Not all of these devices handle authentication in the same manner but the user doesn't care. They need to access their apps from the devices they love. Our Application Access Panel will support the ability for users to access access and launch their apps from any device and anywhere. You can learn more about our plans for application management with Windows Azure Active Directory here.  Try out the preview and start using it today. Enterprise Management: Use Active Directory to Better Manage Windows Azure Windows Azure Active Directory provides the ability to manage your organization in a directory which is hosted entirely in the cloud, or alternatively kept in sync with an on-premises Windows Server Active Directory solution (allowing you to seamlessly integrate with the directory you already have).  With today’s Windows Azure release we are integrating Windows Azure Active Directory even more within the core Windows Azure management experience, and enabling an even richer enterprise security offering.  Specifically: 1) All Windows Azure accounts now have a default Windows Azure Active Directory created for them.  You can create and map any users you want into this directory, and grant administrative rights to manage resources in Windows Azure to these users. 2) You can keep this directory entirely hosted in the cloud – or optionally sync it with your on-premises Windows Server Active Directory.  Both options are free.  The later approach is ideal for companies that wish to use their corporate user identities to sign-in and manage Windows Azure resources.  It also ensures that if an employee leaves an organization, his or her access control rights to the company’s Windows Azure resources are immediately revoked. 3) The Windows Azure Service Management APIs have been updated to support using Windows Azure Active Directory credentials to sign-in and perform management operations.  Prior to today’s release customers had to download and use management certificates (which were not scoped to individual users) to perform management operations.  We still support this management certificate approach (don’t worry – nothing will stop working).  But we think the new Windows Azure Active Directory authentication support enables an even easier and more secure way for customers to manage resources going forward.  4) The Windows Azure SDK 2.2 release (which is also shipping today) includes built-in support for the new Service Management APIs that authenticate with Windows Azure Active Directory, and now allow you to create and manage Windows Azure applications and resources directly within Visual Studio using your Active Directory credentials.  This, combined with updated PowerShell scripts that also support Active Directory, enables an end-to-end enterprise authentication story with Windows Azure. Below are some details on how all of this works: Subscriptions within a Directory As part of today’s update, we have associated all existing Window Azure accounts with a Windows Azure Active Directory (and created one for you if you don’t already have one). When you login to the Windows Azure Management Portal you’ll now see the directory name in the URI of the browser.  For example, in the screen-shot below you can see that I have a “scottgu” directory that my subscriptions are hosted within: Note that you can continue to use Microsoft Accounts (formerly known as Microsoft Live IDs) to sign-into Windows Azure.  These map just fine to a Windows Azure Active Directory – so there is no need to create new usernames that are specific to a directory if you don’t want to.  In the scenario above I’m actually logged in using my @hotmail.com based Microsoft ID which is now mapped to a “scottgu” active directory that was created for me.  By default everything will continue to work just like you used to before. Manage your Directory You can manage an Active Directory (including the one we now create for you by default) by clicking the “Active Directory” tab in the left-hand side of the portal.  This will list all of the directories in your account.  Clicking one the first time will display a getting started page that provides documentation and links to perform common tasks with it: You can use the built-in directory management support within the Windows Azure Management Portal to add/remove/manage users within the directory, enable multi-factor authentication, associate a custom domain (e.g. mycompanyname.com) with the directory, and/or rename the directory to whatever friendly name you want (just click the configure tab to do this).  You can also setup the directory to automatically sync with an on-premises Active Directory using the “Directory Integration” tab. Note that users within a directory by default do not have admin rights to login or manage Windows Azure based resources.  You still need to explicitly grant them co-admin permissions on a subscription for them to login or manage resources in Windows Azure.  You can do this by clicking the Settings tab on the left-hand side of the portal and then by clicking the administrators tab within it. Sign-In Integration within Visual Studio If you install the new Windows Azure SDK 2.2 release, you can now connect to Windows Azure from directly inside Visual Studio without having to download any management certificates.  You can now just right-click on the “Windows Azure” icon within the Server Explorer and choose the “Connect to Windows Azure” context menu option to do so: Doing this will prompt you to enter the email address of the username you wish to sign-in with (make sure this account is a user in your directory with co-admin rights on a subscription): You can use either a Microsoft Account (e.g. Windows Live ID) or an Active Directory based Organizational account as the email.  The dialog will update with an appropriate login prompt depending on which type of email address you enter: Once you sign-in you’ll see the Windows Azure resources that you have permissions to manage show up automatically within the Visual Studio server explorer and be available to start using: No downloading of management certificates required.  All of the authentication was handled using your Windows Azure Active Directory! Manage Subscriptions across Multiple Directories If you have already have multiple directories and multiple subscriptions within your Windows Azure account, we have done our best to create a good default mapping of your subscriptions->directories as part of today’s update.  If you don’t like the default subscription-to-directory mapping we have done you can click the Settings tab in the left-hand navigation of the Windows Azure Management Portal and browse to the Subscriptions tab within it: If you want to map a subscription under a different directory in your account, simply select the subscription from the list, and then click the “Edit Directory” button to choose which directory to map it to.  Mapping a subscription to a different directory takes only seconds and will not cause any of the resources within the subscription to recycle or stop working.  We’ve made the directory->subscription mapping process self-service so that you always have complete control and can map things however you want. Filtering By Directory and Subscription Within the Windows Azure Management Portal you can filter resources in the portal by subscription (allowing you to show/hide different subscriptions).  If you have subscriptions mapped to multiple directory tenants, we also now have a filter drop-down that allows you to filter the subscription list by directory tenant.  This filter is only available if you have multiple subscriptions mapped to multiple directories within your Windows Azure Account:   Windows Azure SDK 2.2 Today we are also releasing a major update of our Windows Azure SDK.  The Windows Azure SDK 2.2 release adds some great new features including: Visual Studio 2013 Support Integrated Windows Azure Sign-In support within Visual Studio Remote Debugging Cloud Services with Visual Studio Firewall Management support within Visual Studio for SQL Databases Visual Studio 2013 RTM VM Images for MSDN Subscribers Windows Azure Management Libraries for .NET Updated Windows Azure PowerShell Cmdlets and ScriptCenter I’ll post a follow-up blog shortly with more details about all of the above. Additional Updates In addition to the above enhancements, today’s release also includes a number of additional improvements: AutoScale: Richer time and date based scheduling support (set different rules on different dates) AutoScale: Ability to Scale to Zero Virtual Machines (very useful for Dev/Test scenarios) AutoScale: Support for time-based scheduling of Mobile Service AutoScale rules Operation Logs: Auditing support for Service Bus management operations Today we also shipped a major update to the Windows Azure SDK – Windows Azure SDK 2.2.  It has so much goodness in it that I have a whole second blog post coming shortly on it! :-) Summary Today’s Windows Azure release enables a bunch of great new scenarios, and enables a much richer enterprise authentication offering. If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using all of the above features today.  Then visit the Windows Azure Developer Center to learn more about how to build apps with it. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Fail to analyze core dump with GDB when main.elf is dynamically linked (uses shared libs)

  - by dscTobi

  Hi all. I'm trying to analyze core dump, but i get following result: GNU gdb 6.6.0.20070423-cvs Copyright (C) 2006 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "--host=mipsel-linux --target=mipsel-linux-uclibc". (gdb) file main.elf Reading symbols from /home/tobi/main.elf...Reading symbols from /home/tobi/main.dbg...done. done. (gdb) core-file /srv/tobi/core warning: .dynamic section for "/lib/libpthread.so.0" is not at the expected address (wrong library or version mismatch?) Error while mapping shared library sections: /lib/libdl.so.0: No such file or directory. Error while mapping shared library sections: /lib/librt.so.0: No such file or directory. Error while mapping shared library sections: /lib/libm.so.0: No such file or directory. Error while mapping shared library sections: /lib/libstdc++.so.6: No such file or directory. Error while mapping shared library sections: /lib/libc.so.0: No such file or directory. warning: .dynamic section for "/lib/libgcc_s.so.1" is not at the expected address (wrong library or version mismatch?) Error while mapping shared library sections: /lib/ld-uClibc.so.0: No such file or directory. Reading symbols from /lib/libpthread.so.0...done. Loaded symbols for /lib/libpthread.so.0 Symbol file not found for /lib/libdl.so.0 Symbol file not found for /lib/librt.so.0 Symbol file not found for /lib/libm.so.0 Symbol file not found for /lib/libstdc++.so.6 Symbol file not found for /lib/libc.so.0 Reading symbols from /lib/libgcc_s.so.1...done. Loaded symbols for /lib/libgcc_s.so.1 Symbol file not found for /lib/ld-uClibc.so.0 warning: Unable to find dynamic linker breakpoint function. GDB will be unable to debug shared library initializers and track explicitly loaded dynamic code. Core was generated by 'root/main.elf'. Program terminated with signal 11, Segmentation fault. #0 0x0046006c in NullPtr (parse_p=0x2ac9dc80, result_sym_p=0x13e3d6c "") at folder/my1.c:1624 1624 *ptr += 13; (gdb) bt #0 0x0046006c in NullPtr (parse_p=0x2ac9dc80, result_sym_p=0x13e3d6c "") at folder/my1.c:1624 #1 0x0047a31c in fn1 (line_ptr=0x2ac9dd18 "ccore_null_pointer", target_ptr=0x13e3d6c "", result_ptr=0x2ac9dd14) at folder/my2.c:980 #2 0x0047b9d0 in fn2 (macro_ptr=0x0, rtn_exp_ptr=0x0) at folder/my3.c:1483 /... some functions .../ #8 0x2aab7f9c in __nptl_setxid () from /lib/libpthread.so.0 Backtrace stopped: frame did not save the PC (gdb) thread apply all bt Thread 159 (process 1093): #0 0x2aac15dc in _Unwind_GetCFA () from /lib/libpthread.so.0 #1 0x2afdfde8 in ?? () warning: GDB cant find the start of the function at 0x2afdfde8. GDB is unable to find the start of the function at 0x2afdfde8 and thus cant determine the size of that functions stack frame. This means that GDB may be unable to access that stack frame, or the frames below it. This problem is most likely caused by an invalid program counter or stack pointer. However, if you think GDB should simply search farther back from 0x2afdfde8 for code which looks like the beginning of a function, you can increase the range of the search using the set heuristic-fence-post command. Backtrace stopped: previous frame inner to this frame (corrupt stack?) Thread 158 (process 1051): #0 0x2aac17bc in pthread_mutexattr_getprioceiling () from /lib/libpthread.so.0 #1 0x2aac17a0 in pthread_mutexattr_getprioceiling () from /lib/libpthread.so.0 Backtrace stopped: previous frame identical to this frame (corrupt stack?) Thread 157 (process 1057): #0 0x2aabf908 in ?? () from /lib/libpthread.so.0 #1 0x00000000 in ?? () Thread 156 (process 1090): #0 0x2aac17bc in pthread_mutexattr_getprioceiling () from /lib/libpthread.so.0 #1 0x2aac17a0 in pthread_mutexattr_getprioceiling () from /lib/libpthread.so.0 Backtrace stopped: previous frame identical to this frame (corrupt stack?) Thread 155 (process 1219): #0 0x2aabf908 in ?? () from /lib/libpthread.so.0 #1 0x00000000 in ?? () Thread 154 (process 1218): #0 0x2aabfb44 in connect () from /lib/libpthread.so.0 #1 0x00000000 in ?? () Thread 153 (process 1096): #0 0x2abc92b4 in ?? () warning: GDB cant find the start of the function at 0x2abc92b4. #1 0x2abc92b4 in ?? () warning: GDB cant find the start of the function at 0x2abc92b4. Backtrace stopped: previous frame identical to this frame (corrupt stack?) Thread 152 (process 1170): #0 0x2aabfb44 in connect () from /lib/libpthread.so.0 #1 0x00000000 in ?? () If i make main.elf statically linked everything is OK and i can see bt of all threads. Any ideas?

  Read the article

• How should I delete a child object from within a parent's slot? Possibly boost::asio specific.

  - by kaliatech

  I have written a network server class that maintains a std::set of network clients. The network clients emit a signal to the network server on disconnect (via boost::bind). When a network client disconnects, the client instance needs to be removed from the Set and eventually deleted. I would think this is a common pattern, but I am having problems that might, or might not, be specific to ASIO. I've tried to trim down to just the relevant code: /** NetworkServer.hpp **/ class NetworkServices : private boost::noncopyable { public: NetworkServices(void); ~NetworkServices(void); private: void run(); void onNetworkClientEvent(NetworkClientEvent&); private: std::set<boost::shared_ptr<const NetworkClient>> clients; }; /** NetworkClient.cpp **/ void NetworkServices::run() { running = true; boost::asio::io_service::work work(io_service); //keeps service running even if no operations // This creates just one thread for the boost::asio async network services boost::thread iot(boost::bind(&NetworkServices::run_io_service, this)); while (running) { boost::system::error_code err; try { tcp::socket* socket = new tcp::socket(io_service); acceptor->accept(*socket, err); if (!err) { NetworkClient* networkClient = new NetworkClient(io_service, boost::shared_ptr<tcp::socket>(socket)); networkClient->networkClientEventSignal.connect(boost::bind(&NetworkServices::onNetworkClientEvent, this, _1)); clients.insert(boost::shared_ptr<NetworkClient>(networkClient)); networkClient->init(); //kicks off 1st asynch_read call } } // etc... } } void NetworkServices::onNetworkClientEvent(NetworkClientEvent& evt) { switch(evt.getType()) { case NetworkClientEvent::CLIENT_ERROR : { boost::shared_ptr<const NetworkClient> clientPtr = evt.getClient().getSharedPtr(); // ------ THIS IS THE MAGIC LINE ----- // If I keep this, the io_service hangs. If I comment it out, // everything works fine (but I never delete the disconnected NetworkClient). // If actually deleted the client here I might expect problems because it is the caller // of this method via boost::signal and bind. However, The clientPtr is a shared ptr, and a // reference is being kept in the client itself while signaling, so // I would the object is not going to be deleted from the heap here. That seems to be the case. // Never-the-less, this line makes all the difference, most likely because it controls whether or not the NetworkClient ever gets deleted. clients.erase(clientPtr); //I should probably put this socket clean-up in NetworkClient destructor. Regardless by doing this, // I would expect the ASIO socket stuff to be adequately cleaned-up after this. tcp::socket& socket = clientPtr->getSocket(); try { socket.shutdown(boost::asio::socket_base::shutdown_both); socket.close(); } catch(...) { CommServerContext::error("Error while shutting down and closing socket."); } break; } default : { break; } } } /** NetworkClient.hpp **/ class NetworkClient : public boost::enable_shared_from_this<NetworkClient>, Client { NetworkClient(boost::asio::io_service& io_service, boost::shared_ptr<tcp::socket> socket); virtual ~NetworkClient(void); inline boost::shared_ptr<const NetworkClient> getSharedPtr() const { return shared_from_this(); }; boost::signal <void (NetworkClientEvent&)> networkClientEventSignal; void onAsyncReadHeader(const boost::system::error_code& error, size_t bytes_transferred); }; /** NetworkClient.cpp - onAsyncReadHeader method called from io_service.run() thread as result of an async_read operation. Error condition usually result of an unexpected client disconnect.**/ void NetworkClient::onAsyncReadHeader( const boost::system::error_code& error, size_t bytes_transferred) { if (error) { //Make sure this instance doesn't get deleted from parent/slot deferencing //Alternatively, somehow schedule for future delete? boost::shared_ptr<const NetworkClient> clientPtr = getSharedPtr(); //Signal to service that this client is disconnecting NetworkClientEvent evt(*this, NetworkClientEvent::CLIENT_ERROR); networkClientEventSignal(evt); networkClientEventSignal.disconnect_all_slots(); return; } I believe it's not safe to delete the client from within the slot handler because the function return would be ... undefined? (Interestingly, it doesn't seem to blow up on me though.) So I've used boost:shared_ptr along with shared_from_this to make sure the client doesn't get deleted until all slots have been signaled. It doesn't seem to really matter though. I believe this question is not specific to ASIO, but the problem manifests in a peculiar way when using ASIO. I have one thread executing io_service.run(). All ASIO read/write operations are performed asynchronously. Everything works fine with multiple clients connecting/disconnecting UNLESS I delete my client object from the Set per the code above. If I delete my client object, the io_service seemingly deadlocks internally and no further asynchronous operations are performed unless I start another thread. I have try/catches around the io_service.run() call and have not been able to detect any errors. Questions: Are there best practices for deleting child objects, that are also signal emitters, from within parent slots? Any ideas as to why the io_service is hanging when I delete my network client object?

  Read the article

• May be my example site may answer my question about ajax call... Help me

  - by booota

  Okay I have this ajax call $('.updatecom .registercomplaint').click(function(){ updatecomplaints(); }); This calls the function updatecomplaints() function updatecomplaints() { var tno = $(".updatecom #tno").val(); var status = $(".updatecom #status").val(); if(status=='DONE') { $(".updatecom #con").val(''); } var tname = $(".updatecom #tname").val(); var rg11 = $(".updatecom #crg11").val(); var rg06 = $(".updatecom #crg06").val(); var tvpins = $(".updatecom #tvpins").val(); var jointer = $(".updatecom #jointer").val(); var cquantity = $(".updatecom #conqty").val(); var nooftv = $(".updatecom #tvno").val(); var misc = $(".updatecom #misc").val(); var tcomments = $(".updatecom #tcomments").val(); var con = $(".updatecom #con").val(); //alert(tno+status+tname+rg11+rg06+tvpins+jointer+cquantity+nooftv+misc+tcomments+con); $.ajax( { type: "POST", url: "up_functions.php", data: "ticket="+ tno +"& opt=upcom" +"& status="+ status +"& tname="+ tname +"& rg11="+ rg11 +"& rg06="+ rg06 +"& tvpins="+ tvpins +"& jointer="+ jointer +"& cquantity="+ cquantity +"& nooftv="+ nooftv +"& misc="+ misc +"& tcomments="+ tcomments +"& con="+ con, success: function(response) { alert(response); } }); } here is my up_functions.php $tno = htmlspecialchars(trim($_REQUEST['ticket'])); $status = htmlspecialchars(trim($_REQUEST['status'])); $tname = htmlspecialchars(trim($_REQUEST['tname'])); $rg11 = htmlspecialchars(trim($_REQUEST['rg11'])); $rg06 = htmlspecialchars(trim($_REQUEST['rg06'])); $tvpins = htmlspecialchars(trim($_REQUEST['tvpins'])); $jointer = htmlspecialchars(trim($_REQUEST['jointer'])); $cquantity = htmlspecialchars(trim($_REQUEST['cquantity'])); $nooftv = htmlspecialchars(trim($_REQUEST['nooftv'])); $misc = htmlspecialchars(trim($_REQUEST['misc'])); $tcomments = htmlspecialchars(trim($_REQUEST['tcomments'])); $con = htmlspecialchars(trim($_REQUEST['con'])); $result=$ptr-upcomticketinfo($tno,$status,$tname,$rg11,$rg06,$tvpins,$jointer,$cquantity,$nooftv,$misc,$tcomments,$con); echo $result; and here is my upconticketinfo() php function function upcomticketinfo($tno,$status,$tname,$rg11,$rg06,$tvpins,$jointer,$cquantity,$nooftv,$misc,$tcomments,$con) { if($con!='' || $con!=NULL) { $this-query = "update booking discription set STATUS='$status',CLOSED ON='$con' where TICKET NO='$tno'"; $this-q_result = mysql_query($this-query,$this-conn) or die(mysql_error()); if($this-q_result) { $query = "update tech detail set TECH NAME='$tname',CABLE RG11='$rg11',CABLE RG06='$rg06',TV PINS USED='$tvpins',JOINTER USED='$jointer',CONNECTOR QTY='$cquantity',NO OF TV='$nooftv',MISC='$misc',TECH COMMENTS='$tcomments' where BOOKING='$tno'"; $q_result = mysql_query($query,$this-conn) or die(mysql_error()); if($q_result) { $response = "updated"; } else { $response = "error"; } } else { $response = "error"; } } else { $this-query = "update booking discription set STATUS='$status' where TICKET NO='$tno'"; $this-q_result = mysql_query($this-query,$this-conn) or die(mysql_error()); if($this-q_result) { $query = "update tech detail set TECH NAME='$tname',CABLE RG11='$rg11',CABLE RG06='$rg06',TV PINS USED='$tvpins',JOINTER USED='$jointer',CONNECTOR QTY='$cquantity',NO OF TV='$nooftv',MISC='$misc',TECH COMMENTS='$tcomments' where BOOKING='$tno'"; $q_result = mysql_query($query,$this-conn) or die(mysql_error()); if($q_result) { $response = "updated"; } else { $response = "error"; } } else { $response = "error"; } } return $response; } Question is that, this code is working just fine in IE8 i.e i am using... but it is not working in FF 3.6.3... I have checked each n everything... One thing is that the code works fine on FF too only when i debug the page with firebug debugger. Otherwise the alert in ajax success shows itself with nothing in it... Help me... Goto link text Enter 6628 in the Ticket No. box under Update Complaint Status section... A new form will open. In that form press update... Try it in FF and IE... IE8 shows the results as needed but FF does not...

  Read the article

• WPF: ContentPresenter changing Foreground unexpectedly depending on where styles are located

  - by VLTII

  Hi, I'm having an issue with the ContentPresenter behaving unexpectedly based on whether the styles are located in the Window.Resources or in a ResourceDictionary. Specifically, I'm setting the Foreground of the default TextBlock to Black, then setting the Foreground value in my default button style to White. If the styles exits on the page like this, they work fine: <Window xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Microsoft_Windows_Themes="clr-namespace:Microsoft.Windows.Themes;assembly=PresentationFramework.Aero" x:Class="TestBed.MainWindow" x:Name="Window" Title="MainWindow" Width="640" Height="480"> <Window.Resources> <Style TargetType="{x:Type TextBlock}"> <Setter Property="Foreground" Value="Black" /> </Style> <Style x:Key="ButtonFocusVisual"> <Setter Property="Control.Template"> <Setter.Value> <ControlTemplate> <Rectangle Stroke="Black" StrokeDashArray="1 2" StrokeThickness="1" Margin="2" SnapsToDevicePixels="true"/> </ControlTemplate> </Setter.Value> </Setter> </Style> <LinearGradientBrush x:Key="ButtonNormalBackground" EndPoint="0,1" StartPoint="0,0"> <GradientStop Color="#F3F3F3" Offset="0"/> <GradientStop Color="#EBEBEB" Offset="0.5"/> <GradientStop Color="#DDDDDD" Offset="0.5"/> <GradientStop Color="#CDCDCD" Offset="1"/> </LinearGradientBrush> <SolidColorBrush x:Key="ButtonNormalBorder" Color="#FF707070"/> <Style TargetType="{x:Type Button}"> <Setter Property="FocusVisualStyle" Value="{StaticResource ButtonFocusVisual}"/> <Setter Property="Background" Value="{StaticResource ButtonNormalBackground}"/> <Setter Property="BorderBrush" Value="{StaticResource ButtonNormalBorder}"/> <Setter Property="BorderThickness" Value="1"/> <Setter Property="Foreground" Value="White"/> <Setter Property="HorizontalContentAlignment" Value="Center"/> <Setter Property="VerticalContentAlignment" Value="Center"/> <Setter Property="Padding" Value="1"/> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="{x:Type Button}"> <Microsoft_Windows_Themes:ButtonChrome x:Name="Chrome" SnapsToDevicePixels="true" Background="{TemplateBinding Background}" BorderBrush="{TemplateBinding BorderBrush}" RenderDefaulted="{TemplateBinding IsDefaulted}" RenderMouseOver="{TemplateBinding IsMouseOver}" RenderPressed="{TemplateBinding IsPressed}"> <ContentPresenter HorizontalAlignment="{TemplateBinding HorizontalContentAlignment}" Margin="{TemplateBinding Padding}" VerticalAlignment="{TemplateBinding VerticalContentAlignment}" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}" RecognizesAccessKey="True"/> </Microsoft_Windows_Themes:ButtonChrome> <ControlTemplate.Triggers> <Trigger Property="IsKeyboardFocused" Value="true"> <Setter Property="RenderDefaulted" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="ToggleButton.IsChecked" Value="true"> <Setter Property="RenderPressed" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="IsEnabled" Value="false"> <Setter Property="Foreground" Value="#ADADAD"/> </Trigger> </ControlTemplate.Triggers> </ControlTemplate> </Setter.Value> </Setter> </Style> </Window.Resources> <StackPanel x:Name="LayoutRoot"> <Button Content="Button" /> </StackPanel> </Window> But if I move those same styles over to a ResourceDictionary, the Foreground of the button switches to black. Updated MainWindow: <Window xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Microsoft_Windows_Themes="clr-namespace:Microsoft.Windows.Themes;assembly=PresentationFramework.Aero" x:Class="TestBed.MainWindow" x:Name="Window" Title="MainWindow" Width="640" Height="480"> <StackPanel x:Name="LayoutRoot"> <Button Content="Button" /> </StackPanel> </Window> ResourceDictionary: <ResourceDictionary xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Microsoft_Windows_Themes="clr-namespace:Microsoft.Windows.Themes;assembly=PresentationFramework.Aero" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d"> <Style TargetType="{x:Type TextBlock}"> <Setter Property="Foreground" Value="Black" /> </Style> <Style x:Key="ButtonFocusVisual"> <Setter Property="Control.Template"> <Setter.Value> <ControlTemplate> <Rectangle Stroke="Black" StrokeDashArray="1 2" StrokeThickness="1" Margin="2" SnapsToDevicePixels="true"/> </ControlTemplate> </Setter.Value> </Setter> </Style> <LinearGradientBrush x:Key="ButtonNormalBackground" EndPoint="0,1" StartPoint="0,0"> <GradientStop Color="#F3F3F3" Offset="0"/> <GradientStop Color="#EBEBEB" Offset="0.5"/> <GradientStop Color="#DDDDDD" Offset="0.5"/> <GradientStop Color="#CDCDCD" Offset="1"/> </LinearGradientBrush> <SolidColorBrush x:Key="ButtonNormalBorder" Color="#FF707070"/> <Style TargetType="{x:Type Button}"> <Setter Property="FocusVisualStyle" Value="{StaticResource ButtonFocusVisual}"/> <Setter Property="Background" Value="{StaticResource ButtonNormalBackground}"/> <Setter Property="BorderBrush" Value="{StaticResource ButtonNormalBorder}"/> <Setter Property="BorderThickness" Value="1"/> <Setter Property="Foreground" Value="White"/> <Setter Property="HorizontalContentAlignment" Value="Center"/> <Setter Property="VerticalContentAlignment" Value="Center"/> <Setter Property="Padding" Value="1"/> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="{x:Type Button}"> <Microsoft_Windows_Themes:ButtonChrome x:Name="Chrome" SnapsToDevicePixels="true" Background="{TemplateBinding Background}" BorderBrush="{TemplateBinding BorderBrush}" RenderDefaulted="{TemplateBinding IsDefaulted}" RenderMouseOver="{TemplateBinding IsMouseOver}" RenderPressed="{TemplateBinding IsPressed}"> <ContentPresenter HorizontalAlignment="{TemplateBinding HorizontalContentAlignment}" Margin="{TemplateBinding Padding}" VerticalAlignment="{TemplateBinding VerticalContentAlignment}" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}" RecognizesAccessKey="True"/> </Microsoft_Windows_Themes:ButtonChrome> <ControlTemplate.Triggers> <Trigger Property="IsKeyboardFocused" Value="true"> <Setter Property="RenderDefaulted" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="ToggleButton.IsChecked" Value="true"> <Setter Property="RenderPressed" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="IsEnabled" Value="false"> <Setter Property="Foreground" Value="#ADADAD"/> </Trigger> </ControlTemplate.Triggers> </ControlTemplate> </Setter.Value> </Setter> </Style> </ResourceDictionary> And my App.xaml because someone will ask for it: <Application xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" x:Class="TestBed.App" StartupUri="MainWindow.xaml"> <Application.Resources> <!-- Resources scoped at the Application level should be defined here. --> <ResourceDictionary> <ResourceDictionary.MergedDictionaries> <ResourceDictionary Source="ResourceDictionary.xaml"/> </ResourceDictionary.MergedDictionaries> </ResourceDictionary> </Application.Resources> </Application> Any help would be greatly appreciated :)

  Read the article

• No bean named 'springSecurityFilterChain' is defined

  - by michaeljackson4ever

  When configs are loaded, I get the error SEVERE: Exception starting filter springSecurityFilterChain org.springframework.beans.factory.NoSuchBeanDefinitionException: No bean named 'springSecurityFilterChain' is defined My sec-config: <http use-expressions="true" access-denied-page="/error/casfailed.html" entry-point-ref="headerAuthenticationEntryPoint"> <intercept-url pattern="/" access="permitAll"/> <!-- <intercept-url pattern="/index.html" access="permitAll"/> --> <intercept-url pattern="/index.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/history.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/absence.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/search.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/employees.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/employee.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/contract.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/myforms.html" access="hasAnyRole('HLO','OPISK')"/> <intercept-url pattern="/vacationmsg.html" access="hasAnyRole('ROLE_USER')"/> <intercept-url pattern="/redirect.jsp" filters="none" /> <intercept-url pattern="/error/**" filters="none" /> <intercept-url pattern="/layout/**" filters="none" /> <intercept-url pattern="/js/**" filters="none" /> <intercept-url pattern="/**" access="isAuthenticated()" /> <!-- session-management invalid-session-url="/absence.html"/ --> <!-- logout logout-success-url="/logout.html"/ --> <custom-filter ref="ssoHeaderAuthenticationFilter" before="CAS_FILTER"/> <!-- CAS_FILTER ??? --> </http> <authentication-manager alias="authenticationManager"> <authentication-provider ref="doNothingAuthenticationProvider"/> </authentication-manager> <beans:bean id="doNothingAuthenticationProvider" class="com.nixu.security.sso.web.DoNothingAuthenticationProvider"/> <beans:bean id="ssoHeaderAuthenticationFilter" class="com.nixu.security.sso.web.HeaderAuthenticationFilter"> <beans:property name="groups"> <beans:map> <beans:entry key="cn=lake,ou=confluence,dc=utu,dc=fi" value="ROLE_ADMIN"/> </beans:map> </beans:property> </beans:bean> <beans:bean id="headerAuthenticationEntryPoint" class="com.nixu.security.sso.web.HeaderAuthenticationEntryPoint"/> And web.xml <context-param> <param-name>contextConfigLocation</param-name> <param-value> /WEB-INF/applicationContext.xml /WEB-INF/sec-config.xml /WEB-INF/idm-config.xml /WEB-INF/ldap-config.xml </param-value> </context-param> <display-name>KeyCard</display-name> <context-param> <param-name>webAppRootKey</param-name> <param-value>KeyCardAppRoot</param-value> </context-param> <context-param> <param-name>log4jConfigLocation</param-name> <param-value>/WEB-INF/log4j.properties</param-value> </context-param> <!-- Reads request input using UTF-8 encoding --> <filter> <filter-name>characterEncodingFilter</filter-name> <filter-class>org.springframework.web.filter.CharacterEncodingFilter</filter-class> <init-param> <param-name>encoding</param-name> <param-value>UTF-8</param-value> </init-param> <init-param> <param-name>forceEncoding</param-name> <param-value>true</param-value> </init-param> </filter> <filter> <filter-name>springSecurityFilterChain</filter-name> <filter-class>org.springframework.web.filter.DelegatingFilterProxy</filter-class> </filter> <filter-mapping> <filter-name>characterEncodingFilter</filter-name> <url-pattern>/*</url-pattern> </filter-mapping> <filter-mapping> <filter-name>springSecurityFilterChain</filter-name> <url-pattern>/*</url-pattern> </filter-mapping> <listener> <listener-class>org.springframework.web.context.ContextLoaderListener</listener-class> </listener> <listener> <listener-class>org.springframework.web.util.Log4jConfigListener</listener-class> </listener> <listener> <!-- this is for session scoped objects --> <listener-class>org.springframework.web.context.request.RequestContextListener</listener-class> </listener> <listener> <listener-class>org.springframework.security.web.session.HttpSessionEventPublisher</listener-class> </listener> <!-- Handles all requests into the application --> <servlet> <servlet-name>KeyCard</servlet-name> <servlet-class>org.springframework.web.servlet.DispatcherServlet</servlet-class> <load-on-startup>1</load-on-startup> </servlet> <servlet> <servlet-name>tiles</servlet-name> <servlet-class>org.apache.tiles.web.startup.TilesServlet</servlet-class> <init-param> <param-name> org.apache.tiles.impl.BasicTilesContainer.DEFINITIONS_CONFIG </param-name> <param-value> /WEB-INF/tilesViewContext.xml </param-value> </init-param> <load-on-startup>2</load-on-startup> </servlet> <servlet-mapping> <servlet-name>KeyCard</servlet-name> <url-pattern>*.html</url-pattern> </servlet-mapping> <session-config> <session-timeout> 120 </session-timeout> </session-config> <welcome-file-list> <welcome-file>index.jsp</welcome-file> </welcome-file-list> <!-- error-page> <exception-type>java.lang.Exception</exception-type> <location>/WEB-INF/error/error.jsp</location> </error-page --> </web-app> What's wrong?

  Read the article

• ContentPresenter changing Foreground unexpectedly depending on where styles are located

  - by VLTII

  Hi, I'm having an issue with the ContentPresenter behaving unexpectedly based on whether the styles are located in the Window.Resources or in a ResourceDictionary. Specifically, I'm setting the Foreground of the default TextBlock to Black, then setting the Foreground value in my default button style to White. If the styles exits on the page like this, they work fine: <Window xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Microsoft_Windows_Themes="clr-namespace:Microsoft.Windows.Themes;assembly=PresentationFramework.Aero" x:Class="TestBed.MainWindow" x:Name="Window" Title="MainWindow" Width="640" Height="480"> <Window.Resources> <Style TargetType="{x:Type TextBlock}"> <Setter Property="Foreground" Value="Black" /> </Style> <Style x:Key="ButtonFocusVisual"> <Setter Property="Control.Template"> <Setter.Value> <ControlTemplate> <Rectangle Stroke="Black" StrokeDashArray="1 2" StrokeThickness="1" Margin="2" SnapsToDevicePixels="true"/> </ControlTemplate> </Setter.Value> </Setter> </Style> <LinearGradientBrush x:Key="ButtonNormalBackground" EndPoint="0,1" StartPoint="0,0"> <GradientStop Color="#F3F3F3" Offset="0"/> <GradientStop Color="#EBEBEB" Offset="0.5"/> <GradientStop Color="#DDDDDD" Offset="0.5"/> <GradientStop Color="#CDCDCD" Offset="1"/> </LinearGradientBrush> <SolidColorBrush x:Key="ButtonNormalBorder" Color="#FF707070"/> <Style TargetType="{x:Type Button}"> <Setter Property="FocusVisualStyle" Value="{StaticResource ButtonFocusVisual}"/> <Setter Property="Background" Value="{StaticResource ButtonNormalBackground}"/> <Setter Property="BorderBrush" Value="{StaticResource ButtonNormalBorder}"/> <Setter Property="BorderThickness" Value="1"/> <Setter Property="Foreground" Value="White"/> <Setter Property="HorizontalContentAlignment" Value="Center"/> <Setter Property="VerticalContentAlignment" Value="Center"/> <Setter Property="Padding" Value="1"/> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="{x:Type Button}"> <Microsoft_Windows_Themes:ButtonChrome x:Name="Chrome" SnapsToDevicePixels="true" Background="{TemplateBinding Background}" BorderBrush="{TemplateBinding BorderBrush}" RenderDefaulted="{TemplateBinding IsDefaulted}" RenderMouseOver="{TemplateBinding IsMouseOver}" RenderPressed="{TemplateBinding IsPressed}"> <ContentPresenter HorizontalAlignment="{TemplateBinding HorizontalContentAlignment}" Margin="{TemplateBinding Padding}" VerticalAlignment="{TemplateBinding VerticalContentAlignment}" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}" RecognizesAccessKey="True"/> </Microsoft_Windows_Themes:ButtonChrome> <ControlTemplate.Triggers> <Trigger Property="IsKeyboardFocused" Value="true"> <Setter Property="RenderDefaulted" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="ToggleButton.IsChecked" Value="true"> <Setter Property="RenderPressed" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="IsEnabled" Value="false"> <Setter Property="Foreground" Value="#ADADAD"/> </Trigger> </ControlTemplate.Triggers> </ControlTemplate> </Setter.Value> </Setter> </Style> </Window.Resources> <StackPanel x:Name="LayoutRoot"> <Button Content="Button" /> </StackPanel> </Window> But if I move those same styles over to a ResourceDictionary, the Foreground of the button switches to black. Updated MainWindow: <Window xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Microsoft_Windows_Themes="clr-namespace:Microsoft.Windows.Themes;assembly=PresentationFramework.Aero" x:Class="TestBed.MainWindow" x:Name="Window" Title="MainWindow" Width="640" Height="480"> <StackPanel x:Name="LayoutRoot"> <Button Content="Button" /> </StackPanel> </Window> ResourceDictionary: <ResourceDictionary xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Microsoft_Windows_Themes="clr-namespace:Microsoft.Windows.Themes;assembly=PresentationFramework.Aero" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d"> <Style TargetType="{x:Type TextBlock}"> <Setter Property="Foreground" Value="Black" /> </Style> <Style x:Key="ButtonFocusVisual"> <Setter Property="Control.Template"> <Setter.Value> <ControlTemplate> <Rectangle Stroke="Black" StrokeDashArray="1 2" StrokeThickness="1" Margin="2" SnapsToDevicePixels="true"/> </ControlTemplate> </Setter.Value> </Setter> </Style> <LinearGradientBrush x:Key="ButtonNormalBackground" EndPoint="0,1" StartPoint="0,0"> <GradientStop Color="#F3F3F3" Offset="0"/> <GradientStop Color="#EBEBEB" Offset="0.5"/> <GradientStop Color="#DDDDDD" Offset="0.5"/> <GradientStop Color="#CDCDCD" Offset="1"/> </LinearGradientBrush> <SolidColorBrush x:Key="ButtonNormalBorder" Color="#FF707070"/> <Style TargetType="{x:Type Button}"> <Setter Property="FocusVisualStyle" Value="{StaticResource ButtonFocusVisual}"/> <Setter Property="Background" Value="{StaticResource ButtonNormalBackground}"/> <Setter Property="BorderBrush" Value="{StaticResource ButtonNormalBorder}"/> <Setter Property="BorderThickness" Value="1"/> <Setter Property="Foreground" Value="White"/> <Setter Property="HorizontalContentAlignment" Value="Center"/> <Setter Property="VerticalContentAlignment" Value="Center"/> <Setter Property="Padding" Value="1"/> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="{x:Type Button}"> <Microsoft_Windows_Themes:ButtonChrome x:Name="Chrome" SnapsToDevicePixels="true" Background="{TemplateBinding Background}" BorderBrush="{TemplateBinding BorderBrush}" RenderDefaulted="{TemplateBinding IsDefaulted}" RenderMouseOver="{TemplateBinding IsMouseOver}" RenderPressed="{TemplateBinding IsPressed}"> <ContentPresenter HorizontalAlignment="{TemplateBinding HorizontalContentAlignment}" Margin="{TemplateBinding Padding}" VerticalAlignment="{TemplateBinding VerticalContentAlignment}" SnapsToDevicePixels="{TemplateBinding SnapsToDevicePixels}" RecognizesAccessKey="True"/> </Microsoft_Windows_Themes:ButtonChrome> <ControlTemplate.Triggers> <Trigger Property="IsKeyboardFocused" Value="true"> <Setter Property="RenderDefaulted" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="ToggleButton.IsChecked" Value="true"> <Setter Property="RenderPressed" TargetName="Chrome" Value="true"/> </Trigger> <Trigger Property="IsEnabled" Value="false"> <Setter Property="Foreground" Value="#ADADAD"/> </Trigger> </ControlTemplate.Triggers> </ControlTemplate> </Setter.Value> </Setter> </Style> </ResourceDictionary> And my App.xaml because someone will ask for it: <Application xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" x:Class="TestBed.App" StartupUri="MainWindow.xaml"> <Application.Resources> <!-- Resources scoped at the Application level should be defined here. --> <ResourceDictionary> <ResourceDictionary.MergedDictionaries> <ResourceDictionary Source="ResourceDictionary.xaml"/> </ResourceDictionary.MergedDictionaries> </ResourceDictionary> </Application.Resources> </Application> Any help would be greatly appreciated :)

  Read the article

• Referencing CDI producer method result in h:selectOneMenu

  - by user953217

  I have a named session scoped bean CustomerRegistration which has a named producer method getNewCustomer which returns a Customer object. There is also CustomerListProducer class which produces all customers as list from the database. On the selectCustomer.xhtml page the user is then able to select one of the customers and submit the selection to the application which then simply prints out the last name of the selected customer. Now this only works when I reference the selected customer on the facelets page via #{customerRegistration.newCustomer}. When I simply use #{newCustomer} then the output for the last name is null whenever I submit the form. What's going on here? Is this the expected behavior as according to chapter 7.1 Restriction upon bean instantion of JSR-299 spec? It says: ... However, if the application directly instantiates a bean class, instead of letting the container perform instantiation, the resulting instance is not managed by the container and is not a contextual instance as defined by Section 6.5.2, “Contextual instance of a bean”. Furthermore, the capabilities listed in Section 2.1, “Functionality provided by the container to the bean” will not be available to that particular instance. In a deployed application, it is the container that is responsible for instantiating beans and initializing their dependencies. ... Here's the code: Customer.java: @javax.persistence.Entity @Veto public class Customer implements Serializable, Entity { private static final long serialVersionUID = 122193054725297662L; @Column(name = "first_name") private String firstName; @Column(name = "last_name") private String lastName; @Id @GeneratedValue() private Long id; public String getFirstName() { return firstName; } public void setFirstName(String firstName) { this.firstName = firstName; } public String getLastName() { return lastName; } public void setLastName(String lastName) { this.lastName = lastName; } @Override public String toString() { return firstName + ", " + lastName; } @Override public Long getId() { return this.id; } } CustomerListProducer.java: @SessionScoped public class CustomerListProducer implements Serializable { @Inject private EntityManager em; private List<Customer> customers; @Inject @Category("helloworld_as7") Logger log; // @Named provides access the return value via the EL variable name // "members" in the UI (e.g., // Facelets or JSP view) @Produces @Named public List<Customer> getCustomers() { return customers; } public void onCustomerListChanged( @Observes(notifyObserver = Reception.IF_EXISTS) final Customer customer) { // retrieveAllCustomersOrderedByName(); log.info(customer.toString()); } @PostConstruct public void retrieveAllCustomersOrderedByName() { CriteriaBuilder cb = em.getCriteriaBuilder(); CriteriaQuery<Customer> criteria = cb.createQuery(Customer.class); Root<Customer> customer = criteria.from(Customer.class); // Swap criteria statements if you would like to try out type-safe // criteria queries, a new // feature in JPA 2.0 // criteria.select(member).orderBy(cb.asc(member.get(Member_.name))); criteria.select(customer).orderBy(cb.asc(customer.get("lastName"))); customers = em.createQuery(criteria).getResultList(); } } CustomerRegistration.java: @Named @SessionScoped public class CustomerRegistration implements Serializable { @Inject @Category("helloworld_as7") private Logger log; private Customer newCustomer; @Produces @Named public Customer getNewCustomer() { return newCustomer; } public void selected() { log.info("Customer " + newCustomer.getLastName() + " ausgewählt."); } @PostConstruct public void initNewCustomer() { newCustomer = new Customer(); } public void setNewCustomer(Customer newCustomer) { this.newCustomer = newCustomer; } } not working selectCustomer.xhtml: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:f="http://java.sun.com/jsf/core" xmlns:h="http://java.sun.com/jsf/html" xmlns:ui="http://java.sun.com/jsf/facelets"> <h:head> <title>Auswahl</title> </h:head> <h:body> <h:form> <h:selectOneMenu value="#{newCustomer}" converter="customerConverter"> <f:selectItems value="#{customers}" var="current" itemLabel="#{current.firstName}, #{current.lastName}" /> </h:selectOneMenu> <h:panelGroup id="auswahl"> <h:outputText value="#{newCustomer.lastName}" /> </h:panelGroup> <h:commandButton value="Klick" action="#{customerRegistration.selected}" /> </h:form> </h:body> </html> working selectCustomer.xhtml: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:f="http://java.sun.com/jsf/core" xmlns:h="http://java.sun.com/jsf/html" xmlns:ui="http://java.sun.com/jsf/facelets"> <h:head> <title>Auswahl</title> </h:head> <h:body> <h:form> <h:selectOneMenu value="#{customerRegistration.newCustomer}" converter="customerConverter"> <f:selectItems value="#{customers}" var="current" itemLabel="#{current.firstName}, #{current.lastName}" /> </h:selectOneMenu> <h:panelGroup id="auswahl"> <h:outputText value="#{newCustomer.lastName}" /> </h:panelGroup> <h:commandButton value="Klick" action="#{customerRegistration.selected}" /> </h:form> </h:body> </html> CustomerConverter.java: @SessionScoped @FacesConverter("customerConverter") public class CustomerConverter implements Converter, Serializable { private static final long serialVersionUID = -6093400626095413322L; @Inject EntityManager entityManager; @Override public Object getAsObject(FacesContext context, UIComponent component, String value) { Long id = Long.valueOf(value); return entityManager.find(Customer.class, id); } @Override public String getAsString(FacesContext context, UIComponent component, Object value) { return ((Customer) value).getId().toString(); } }

  Read the article

• Segmentation fault in my C program

  - by user233542

  I don't understand why this would give me a seg fault. Any ideas? This is the function that returns the signal to stop the program (plus the other function that is called within this): double bisect(double A0,double A1,double Sol[N],double tol,double c) { double Amid,shot; while (A1-A0 > tol) { Amid = 0.5*(A0+A1); shot = shoot(Sol, Amid, c); if (shot==2.*Pi) { return Amid; } if (shot > 2.*Pi){ A1 = Amid; } else if (shot < 2.*Pi){ A0 = Amid; } } return 0.5*(A1+A0); } double shoot(double Sol[N],double A,double c) { int i,j; /*Initial Conditions*/ for (i=0;i<buff;i++) { Sol[i] = 0.; } for (i=buff+l;i<N;i++) { Sol[i] = 2.*Pi; } Sol[buff]= 0; Sol[buff+1]= A*exp(sqrt(1+3*c)*dx); for (i=buff+2;i<buff+l;i++) { Sol[i] = (dx*dx)*( sin(Sol[i-1]) + c*sin(3.*(Sol[i-1])) ) - Sol[i-2] + 2.*Sol[i-1]; } return Sol[i-1]; } The values buff, l, N are defined using a #define statement. l = 401, buff = 50, N = 2000 Here is the full code: #include <stdio.h> #include <stdlib.h> #include <math.h> #define w 10 /*characteristic width of a soliton*/ #define dx 0.05 /*distance between lattice sites*/ #define s (2*w)/dx /*size of soliton shape*/ #define l (int)(s+1) /*array length for soliton*/ #define N (int)2000 /*length of field array--lattice sites*/ #define Pi (double)4*atan(1) #define buff (int)50 double shoot(double Sol[N],double A,double c); double bisect(double A0,double A1,double Sol[N],double tol,double c); void super_pos(double antiSol[N],double Sol[N],double phi[][N]); void vel_ver(double phi[][N],double v,double c,int tsteps,double dt); int main(int argc, char **argv) { double c,Sol[N],antiSol[N],A,A0,A1,tol,v,dt; int tsteps,i; FILE *fp1,*fp2,*fp3; fp1 = fopen("soliton.dat","w"); fp2 = fopen("final-phi.dat","w"); fp3 = fopen("energy.dat","w"); printf("Please input the number of time steps:"); scanf("%d",&tsteps); printf("Also, enter the time step size:"); scanf("%lf",&dt); do{ printf("Please input the parameter c in the interval [-1/3,1]:"); scanf("%lf",&c);} while(c < (-1./3.) || c > 1.); printf("Please input the inital speed of eiter soliton:"); scanf("%lf",&v); double phi[tsteps+1][N]; tol = 0.0000001; A0 = 0.; A1 = 2.*Pi; A = bisect(A0,A1,Sol,tol,c); shoot(Sol,A,c); for (i=0;i<N;i++) { fprintf(fp1,"%d\t",i); fprintf(fp1,"%lf\n",Sol[i]); } fclose(fp1); super_pos(antiSol,Sol,phi); /*vel_ver(phi,v,c,tsteps,dt); for (i=0;i<N;i++){ fprintf(fp2,"%d\t",i); fprintf(fp2,"%lf\n",phi[tsteps][i]); }*/ } double shoot(double Sol[N],double A,double c) { int i,j; /*Initial Conditions*/ for (i=0;i<buff;i++) { Sol[i] = 0.; } for (i=buff+l;i<N;i++) { Sol[i] = 2.*Pi; } Sol[buff]= 0; Sol[buff+1]= A*exp(sqrt(1+3*c)*dx); for (i=buff+2;i<buff+l;i++) { Sol[i] = (dx*dx)*( sin(Sol[i-1]) + c*sin(3.*(Sol[i-1])) ) - Sol[i-2] + 2.*Sol[i-1]; } return Sol[i-1]; } double bisect(double A0,double A1,double Sol[N],double tol,double c) { double Amid,shot; while (A1-A0 > tol) { Amid = 0.5*(A0+A1); shot = shoot(Sol, Amid, c); if (shot==2.*Pi) { return Amid; } if (shot > 2.*Pi){ A1 = Amid; } else if (shot < 2.*Pi){ A0 = Amid; } } return 0.5*(A1+A0); } void super_pos(double antiSol[N],double Sol[N],double phi[][N]) { int i; /*for (i=0;i<N;i++) { phi[i]=0; } for (i=buffer+s;i<1950-s;i++) { phi[i]=2*Pi; }*/ for (i=0;i<N;i++) { antiSol[i] = Sol[N-i]; } /*for (i=0;i<s+1;i++) { phi[buffer+j] = Sol[j]; phi[1549+j] = antiSol[j]; }*/ for (i=0;i<N;i++) { phi[0][i] = antiSol[i] + Sol[i] - 2.*Pi; } } /* This funciton will set the 2nd input array to the derivative at the time t, for all points x in the lattice */ void deriv2(double phi[][N],double DphiDx2[][N],int t) { //double SolDer2[s+1]; int x; for (x=0;x<N;x++) { DphiDx2[t][x] = (phi[buff+x+1][t] + phi[buff+x-1][t] - 2.*phi[x][t])/(dx*dx); } /*for (i=0;i<N;i++) { ptr[i] = &SolDer2[i]; }*/ //return DphiDx2[x]; } void vel_ver(double phi[][N],double v,double c,int tsteps,double dt) { int t,x; double d1,d2,dp,DphiDx1[tsteps+1][N],DphiDx2[tsteps+1][N],dpdt[tsteps+1][N],p[tsteps+1][N]; for (t=0;t<tsteps;t++){ if (t==0){ for (x=0;x<N;x++){//inital conditions deriv2(phi,DphiDx2,t); dpdt[t][x] = DphiDx2[t][x] - sin(phi[t][x]) - sin(3.*phi[t][x]); DphiDx1[t][x] = (phi[t][x+1] - phi[t][x])/dx; p[t][x] = -v*DphiDx1[t][x]; } } for (x=0;x<N;x++){//velocity-verlet phi[t+1][x] = phi[t][x] + dt*p[t][x] + (dt*dt/2)*dpdt[t][x]; p[t+1][x] = p[t][x] + (dt/2)*dpdt[t][x]; deriv2(phi,DphiDx2,t+1); dpdt[t][x] = DphiDx2[t][x] - sin(phi[t+1][x]) - sin(3.*phi[t+1][x]); p[t+1][x] += (dt/2)*dpdt[t+1][x]; } } } So, this really isn't due to my overwriting the end of the Sol array. I've commented out both functions that I suspected of causing the problem (bisect or shoot) and inserted a print function. Two things happen. When I have code like below: double A,Pi,B,c; c=0; Pi = 4.*atan(1.); A = Pi; B = 1./4.; printf("%lf",B); B = shoot(Sol,A,c); printf("%lf",B); I get a segfault from the function, shoot. However, if I take away the shoot function so that I have: double A,Pi,B,c; c=0; Pi = 4.*atan(1.); A = Pi; B = 1./4.; printf("%lf",B); it gives me a segfault at the printf... Why!?

  Read the article

• JNI String Corruption

  - by Chris Dennett

  Hi everyone, I'm getting weird string corruption across JNI calls which is causing problems on the the Java side. Every so often, I'll get a corrupted string in the passed array, which sometimes has existing parts of the original non-corrupted string. The C++ code is supposed to set the first index of the array to the address, it's a nasty hack to get around method call limitations. Additionally, the application is multi-threaded. remoteaddress[0]: 10.1.1.2:49153 remoteaddress[0]: 10.1.4.2:49153 remoteaddress[0]: 10.1.6.2:49153 remoteaddress[0]: 10.1.2.2:49153 remoteaddress[0]: 10.1.9.2:49153 remoteaddress[0]: {garbage here} java.lang.NullPointerException at kokuks.KKSAddress.<init>(KKSAddress.java:139) at kokuks.KKSAddress.createAddress(KKSAddress.java:48) at kokuks.KKSSocket._recvFrom(KKSSocket.java:963) at kokuks.scheduler.RecvOperation$1.execute(RecvOperation.java:144) at kokuks.scheduler.RecvOperation$1.execute(RecvOperation.java:1) at kokuks.KKSEvent.run(KKSEvent.java:58) at kokuks.KokuKS.handleJNIEventExpiry(KokuKS.java:872) at kokuks.KokuKS.handleJNIEventExpiry_fjni(KokuKS.java:880) at kokuks.KokuKS.runSimulator_jni(Native Method) at kokuks.KokuKS$1.run(KokuKS.java:773) at java.lang.Thread.run(Thread.java:717) remoteaddress[0]: 10.1.7.2:49153 The null pointer exception comes from trying to use the corrupt string. In C++, the address prints to standard out normally, but doing this reduces the rate of errors, from what I can see. The C++ code (if it helps): /* * Class: kokuks_KKSSocket * Method: recvFrom_jni * Signature: (Ljava/lang/String;[Ljava/lang/String;Ljava/nio/ByteBuffer;IIJ)I */ JNIEXPORT jint JNICALL Java_kokuks_KKSSocket_recvFrom_1jni (JNIEnv *env, jobject obj, jstring sockpath, jobjectArray addrarr, jobject buf, jint position, jint limit, jlong flags) { if (addrarr && env->GetArrayLength(addrarr) > 0) { env->SetObjectArrayElement(addrarr, 0, NULL); } jboolean iscopy; const char* cstr = env->GetStringUTFChars(sockpath, &iscopy); std::string spath = std::string(cstr); env->ReleaseStringUTFChars(sockpath, cstr); // release me! if (KKS_DEBUG) { std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << std::endl; } ns3::Ptr<ns3::Socket> socket = ns3::Names::Find<ns3::Socket>(spath); if (!socket) { std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " socket not found for path!!" << std::endl; return -1; // not found } if (!addrarr) { std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " array to set sender is null" << std::endl; return -1; } jsize arrsize = env->GetArrayLength(addrarr); if (arrsize < 1) { std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " array too small to set sender!" << std::endl; return -1; } uint8_t* bufaddr = (uint8_t*)env->GetDirectBufferAddress(buf); long bufcap = env->GetDirectBufferCapacity(buf); uint8_t* realbufaddr = bufaddr + position; uint32_t remaining = limit - position; if (KKS_DEBUG) { std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " bufaddr: " << bufaddr << ", cap: " << bufcap << std::endl; } ns3::Address aaddr; uint32_t mflags = flags; int ret = socket->RecvFrom(realbufaddr, remaining, mflags, aaddr); if (ret > 0) { if (KKS_DEBUG) std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " addr: " << aaddr << std::endl; ns3::InetSocketAddress insa = ns3::InetSocketAddress::ConvertFrom(aaddr); std::stringstream ss; insa.GetIpv4().Print(ss); ss << ":" << insa.GetPort() << std::ends; if (KKS_DEBUG) std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " addr: " << ss.str() << std::endl; jsize index = 0; const char *cstr = ss.str().c_str(); jstring jaddr = env->NewStringUTF(cstr); if (jaddr == NULL) std::cout << "[kks-c~" << spath << "] " << __PRETTY_FUNCTION__ << " jaddr is null!!" << std::endl; //jaddr = (jstring)env->NewGlobalRef(jaddr); env->SetObjectArrayElement(addrarr, index, jaddr); //if (env->ExceptionOccurred()) { // env->ExceptionDescribe(); //} } jint jret = ret; return jret; } The Java code (if it helps): /** * Pass an array of size 1 into remote address, and this will be set with * the sender of the packet (hax). This emulates C++ references. * * @param remoteaddress * @param buf * @param flags * @return */ public int _recvFrom(final KKSAddress remoteaddress[], ByteBuffer buf, long flags) { if (!kks.isCurrentlyThreadSafe()) throw new RuntimeException( "Not currently thread safe for ns-3 functions!" ); //lock.lock(); try { if (!buf.isDirect()) return -6; // not direct!! final String[] remoteAddrStr = new String[1]; int ret = 0; ret = recvFrom_jni( path.toPortableString(), remoteAddrStr, buf, buf.position(), buf.limit(), flags ); if (ret > 0) { System.out.println("remoteaddress[0]: " + remoteAddrStr[0]); remoteaddress[0] = KKSAddress.createAddress(remoteAddrStr[0]); buf.position(buf.position() + ret); } return ret; } finally { errNo = _getErrNo(); //lock.unlock(); } } public int recvFrom(KKSAddress[] fromaddress, final ByteBuffer bytes, long flags, long timeoutMS) { if (KokuKS.DEBUG_MODE) printMessage("public synchronized int recvFrom(KKSAddress[] fromaddress, final ByteBuffer bytes, long flags, long timeoutMS)"); if (kks.isCurrentlyThreadSafe()) { return _recvFrom(fromaddress, bytes, flags); // avoid event } fromaddress[0] = null; RecvOperation ro = new RecvOperation( kks, this, flags, true, bytes, timeoutMS ); ro.start(); fromaddress[0] = ro.getFrom(); return ro.getRetCode(); }

  Read the article

• Sharepoint Error: [COMException (0x80004005): Cannot complete this action.

  - by ifunky

  Hi, I've created a site basic definition that uses different master and default pages. Everything works quite well except for whenever I create a new site based on the definition I receive the following error when browsing to the new site: [COMException (0x80004005): Cannot complete this action. Please try again.] Please try again.] Microsoft.SharePoint.Library.SPRequestInternalClass.GetFileAndMetaInfo(String bstrUrl, Byte bPageView, Byte bPageMode, Byte bGetBuildDependencySet, String bstrCurrentFolderUrl, Boolean& pbCanCustomizePages, Boolean& pbCanPersonalizeWebParts, Boolean& pbCanAddDeleteWebParts, Boolean& pbGhostedDocument, Boolean& pbDefaultToPersonal, String& pbstrSiteRoot, Guid& pgSiteId, UInt32& pdwVersion, String& pbstrTimeLastModified, String& pbstrContent, Byte& pVerGhostedSetupPath, UInt32& pdwPartCount, Object& pvarMetaData, Object& pvarMultipleMeetingDoclibRootFolders, String& pbstrRedirectUrl, Boolean& pbObjectIsList, Guid& pgListId, UInt32& pdwItemId, Int64& pllListFlags, Boolean& pbAccessDenied, Guid& pgDocId, Byte& piLevel, UInt64& ppermMask, Object& pvarBuildDependencySet, UInt32& pdwNumBuildDependencies, Object& pvarBuildDependencies, String& pbstrFolderUrl, String& pbstrContentTypeOrder) +0 Microsoft.SharePoint.Library.SPRequest.GetFileAndMetaInfo(String bstrUrl, Byte bPageView, Byte bPageMode, Byte bGetBuildDependencySet, String bstrCurrentFolderUrl, Boolean& pbCanCustomizePages, Boolean& pbCanPersonalizeWebParts, Boolean& pbCanAddDeleteWebParts, Boolean& pbGhostedDocument, Boolean& pbDefaultToPersonal, String& pbstrSiteRoot, Guid& pgSiteId, UInt32& pdwVersion, String& pbstrTimeLastModified, String& pbstrContent, Byte& pVerGhostedSetupPath, UInt32& pdwPartCount, Object& pvarMetaData, Object& pvarMultipleMeetingDoclibRootFolders, String& pbstrRedirectUrl, Boolean& pbObjectIsList, Guid& pgListId, UInt32& pdwItemId, Int64& pllListFlags, Boolean& pbAccessDenied, Guid& pgDocId, Byte& piLevel, UInt64& ppermMask, Object& pvarBuildDependencySet, UInt32& pdwNumBuildDependencies, Object& pvarBuildDependencies, String& pbstrFolderUrl, String& pbstrContentTypeOrder) +219 [SPException: Cannot complete this action. Please try again.] I'm able to work around this by checking out the new master page and checking it back in again and after doing so there are no further issues at all. Any ideas to what could cause this? Thanks Dan ONET.XML module section: <Modules> <Module Name="CustomMasterPage" List="116" Url="_catalogs/masterpage" RootWebOnly="FALSE"> <File Url="Shoes.master" Type="GhostableInLibrary" IgnoreIfAlreadyExists="TRUE" /> </Module> <Module Name="Default" List="116" Url=""> <File Url="default.aspx" Name="default.aspx" NavBarHome="True" IgnoreIfAlreadyExists="FALSE"> <AllUsersWebPart WebPartZoneID="Left" WebPartOrder="1"> &lt;webParts&gt;&lt;webPart xmlns="http://schemas.microsoft.com/WebPart/v3"&gt;&lt;metaData&gt;&lt;type name="BCM.SharePoint.Shoes.ShoesComponents.FooterLinks, BCM.SharePoint.Shoes.ShoesComponents, Version=1.0.0.0, Culture=neutral, PublicKeyToken=2881713f39360b71" /&gt;&lt;importErrorMessage&gt;Cannot import this Web Part.&lt;/importErrorMessage&gt;&lt;/metaData&gt;&lt;data&gt;&lt;properties&gt;&lt;property name="AllowClose" type="bool"&gt;True&lt;/property&gt;&lt;property name="Width" type="string" /&gt;&lt;property name="MyProperty" type="string"&gt;Hello SharePoint&lt;/property&gt;&lt;property name="AllowMinimize" type="bool"&gt;True&lt;/property&gt;&lt;property name="AllowConnect" type="bool"&gt;True&lt;/property&gt;&lt;property name="ChromeType" type="chrometype"&gt;None&lt;/property&gt;&lt;property name="TitleIconImageUrl" type="string"&gt;/_layouts/images/BCM_SharePoint_Shoes/wp_FooterLinks.gif&lt;/property&gt;&lt;property name="Description" type="string"&gt;FooterLinks Description&lt;/property&gt;&lt;property name="Hidden" type="bool"&gt;False&lt;/property&gt;&lt;property name="TitleUrl" type="string" /&gt;&lt;property name="AllowEdit" type="bool"&gt;True&lt;/property&gt;&lt;property name="Height" type="string" /&gt;&lt;property name="MissingAssembly" type="string"&gt;Cannot import this Web Part.&lt;/property&gt;&lt;property name="HelpUrl" type="string" /&gt;&lt;property name="Title" type="string" /&gt;&lt;property name="CatalogIconImageUrl" type="string"&gt;/_layouts/images/BCM_SharePoint_Shoes/wp_FooterLinks.gif&lt;/property&gt;&lt;property name="Direction" type="direction"&gt;NotSet&lt;/property&gt;&lt;property name="ChromeState" type="chromestate"&gt;Normal&lt;/property&gt;&lt;property name="AllowZoneChange" type="bool"&gt;True&lt;/property&gt;&lt;property name="AllowHide" type="bool"&gt;True&lt;/property&gt;&lt;property name="HelpMode" type="helpmode"&gt;Modeless&lt;/property&gt;&lt;property name="ExportMode" type="exportmode"&gt;All&lt;/property&gt;&lt;/properties&gt;&lt;/data&gt;&lt;/webPart&gt;&lt;/webParts&gt; </AllUsersWebPart> <AllUsersWebPart WebPartZoneID="Left" WebPartOrder="0"> &lt;webParts&gt;&lt;webPart xmlns="http://schemas.microsoft.com/WebPart/v3"&gt;&lt;metaData&gt;&lt;type name="BCM.SharePoint.Shoes.ShoesComponents.SubFooterLinks, BCM.SharePoint.Shoes.ShoesComponents, Version=1.0.0.0, Culture=neutral, PublicKeyToken=2881713f39360b71" /&gt;&lt;importErrorMessage&gt;Cannot import this Web Part.&lt;/importErrorMessage&gt;&lt;/metaData&gt;&lt;data&gt;&lt;properties&gt;&lt;property name="AllowClose" type="bool"&gt;True&lt;/property&gt;&lt;property name="Width" type="string" /&gt;&lt;property name="MyProperty" type="string"&gt;Hello SharePoint&lt;/property&gt;&lt;property name="AllowMinimize" type="bool"&gt;True&lt;/property&gt;&lt;property name="AllowConnect" type="bool"&gt;True&lt;/property&gt;&lt;property name="ChromeType" type="chrometype"&gt;None&lt;/property&gt;&lt;property name="TitleIconImageUrl" type="string"&gt;/_layouts/images/BCM_SharePoint_Shoes/wp_SubFooterLinks.gif&lt;/property&gt;&lt;property name="Description" type="string"&gt;Shoes home page links (under the hero image)&lt;/property&gt;&lt;property name="Hidden" type="bool"&gt;False&lt;/property&gt;&lt;property name="TitleUrl" type="string" /&gt;&lt;property name="AllowEdit" type="bool"&gt;True&lt;/property&gt;&lt;property name="Height" type="string" /&gt;&lt;property name="MissingAssembly" type="string"&gt;Cannot import this Web Part.&lt;/property&gt;&lt;property name="HelpUrl" type="string" /&gt;&lt;property name="Title" type="string" /&gt;&lt;property name="CatalogIconImageUrl" type="string"&gt;/_layouts/images/BCM_SharePoint_Shoes/wp_SubFooterLinks.gif&lt;/property&gt;&lt;property name="Direction" type="direction"&gt;NotSet&lt;/property&gt;&lt;property name="ChromeState" type="chromestate"&gt;Normal&lt;/property&gt;&lt;property name="AllowZoneChange" type="bool"&gt;True&lt;/property&gt;&lt;property name="AllowHide" type="bool"&gt;True&lt;/property&gt;&lt;property name="HelpMode" type="helpmode"&gt;Modeless&lt;/property&gt;&lt;property name="ExportMode" type="exportmode"&gt;All&lt;/property&gt;&lt;/properties&gt;&lt;/data&gt;&lt;/webPart&gt;&lt;/webParts&gt; </AllUsersWebPart> <NavBarPage Name="$Resources:core,nav_Home;" ID="1002" Position="Start" /> <NavBarPage Name="$Resources:core,nav_Home;" ID="0" Position="Start" /> </File> </Module> </Modules> LOG OUTPUT: 05/21/2010 12:22:55.11 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72nz Medium Videntityinfo::isFreshToken reported failure. 05/21/2010 12:22:55.19 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88yv Medium Creating default lists 05/21/2010 12:22:55.19 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72lp Medium Creating directory Lists 05/21/2010 12:22:55.26 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88yf Medium Creating list "Master Page Gallery" in web "http://mmm-dev-ll/sites/Shoes/test" at URL "_catalogs/masterpage", (setuppath: "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\12\Template\global\lists\mplib") 05/21/2010 12:22:55.28 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88y1 Medium No document templates uploaded for list "Master Page Gallery" -- none found for list template "100". 05/21/2010 12:22:55.28 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72kc Medium Failed to find generic XML file at "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\12\Template\xml\onet.xml", falling back to global site definition. 05/21/2010 12:22:56.22 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88yz Medium Creating default modules at URL "http://mmm-dev-ll/sites/Shoes/test" 05/21/2010 12:22:56.22 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8e27 Medium Ensuring module folder _catalogs/masterpage 05/21/2010 12:22:56.89 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72h7 Medium Applying template "SubSite#1" to web at URL "http://mmm-dev-ll/sites/Shoes/test". 05/21/2010 12:22:57.09 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88yy Medium Activating web-scoped features for template "SubSite#1" at URL "http://mmm-dev-ll/sites/Shoes/test" 05/21/2010 12:22:57.12 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8l1c Medium Preparing 20 features for activation 05/21/2010 12:22:57.14 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8l1d Medium Feature Activation: Batch Activating Features at URL http://mmm-dev-ll/sites/Shoes/test 'AnnouncementsList' (ID: '00bfea71-d1ce-42de-9c63-a44004ce0104'), 'ContactsList' (ID: '00bfea71-7e6d-4186-9ba8-c047ac750105'), 'CustomList' (ID: '00bfea71-de22-43b2-a848-c05709900100'), 'DataSourceLibrary' (ID: '00bfea71-f381-423d-b9d1-da7a54c50110'), 'DiscussionsList' (ID: '00bfea71-6a49-43fa-b535-d15c05500108'), 'DocumentLibrary' (ID: '00bfea71-e717-4e80-aa17-d0c71b360101'), 'EventsList' (ID: '00bfea71-ec85-4903-972d-ebe475780106'), 'GanttTasksList' (ID: '00bfea71-513d-4ca0-96c2-6a47775c0119'), 'GridList' (ID: '00bfea71-3a1d-41d3-a0ee-651d11570120'), 'IssuesList' (ID: '00bfea71-5932-4f9c-ad71-1557e5751100'), 'LinksList' (ID: '00bfea71-2062-426c-90bf-714c59600103'), 'NoCodeWorkflowLibrary' (ID: '00bfe... 05/21/2010 12:22:57.14* w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8l1d Medium ...a71-f600-43f6-a895-40c0de7b0117'), 'PictureLibrary' (ID: '00bfea71-52d4-45b3-b544-b1c71b620109'), 'SurveysList' (ID: '00bfea71-eb8a-40b1-80c7-506be7590102'), 'TasksList' (ID: '00bfea71-a83e-497e-9ba0-7a5c597d0107'), 'WebPageLibrary' (ID: '00bfea71-c796-4402-9f2f-0eb9a6e71b18'), 'workflowProcessList' (ID: '00bfea71-2d77-4a75-9fca-76516689e21a'), 'WorkflowHistoryList' (ID: '00bfea71-4ea5-48d4-a4ad-305cf7030140'), 'XmlFormLibrary' (ID: '00bfea71-1e1d-4562-b56a-f05371bb0115'), 'TeamCollab' (ID: '00bfea71-4ea5-48d4-a4ad-7ea5c011abe5'), . 05/21/2010 12:22:57.15 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8l1f Medium Feature Activation: Batch Activated Features at URL http://mmm-dev-ll/sites/Shoes/test 'AnnouncementsList' (ID: '00bfea71-d1ce-42de-9c63-a44004ce0104'), 'ContactsList' (ID: '00bfea71-7e6d-4186-9ba8-c047ac750105'), 'CustomList' (ID: '00bfea71-de22-43b2-a848-c05709900100'), 'DataSourceLibrary' (ID: '00bfea71-f381-423d-b9d1-da7a54c50110'), 'DiscussionsList' (ID: '00bfea71-6a49-43fa-b535-d15c05500108'), 'DocumentLibrary' (ID: '00bfea71-e717-4e80-aa17-d0c71b360101'), 'EventsList' (ID: '00bfea71-ec85-4903-972d-ebe475780106'), 'GanttTasksList' (ID: '00bfea71-513d-4ca0-96c2-6a47775c0119'), 'GridList' (ID: '00bfea71-3a1d-41d3-a0ee-651d11570120'), 'IssuesList' (ID: '00bfea71-5932-4f9c-ad71-1557e5751100'), 'LinksList' (ID: '00bfea71-2062-426c-90bf-714c59600103'), 'NoCodeWorkflowLibrary' (ID: '00bfea... 05/21/2010 12:22:57.15* w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8l1f Medium ...71-f600-43f6-a895-40c0de7b0117'), 'PictureLibrary' (ID: '00bfea71-52d4-45b3-b544-b1c71b620109'), 'SurveysList' (ID: '00bfea71-eb8a-40b1-80c7-506be7590102'), 'TasksList' (ID: '00bfea71-a83e-497e-9ba0-7a5c597d0107'), 'WebPageLibrary' (ID: '00bfea71-c796-4402-9f2f-0eb9a6e71b18'), 'workflowProcessList' (ID: '00bfea71-2d77-4a75-9fca-76516689e21a'), 'WorkflowHistoryList' (ID: '00bfea71-4ea5-48d4-a4ad-305cf7030140'), 'XmlFormLibrary' (ID: '00bfea71-1e1d-4562-b56a-f05371bb0115'), 'TeamCollab' (ID: '00bfea71-4ea5-48d4-a4ad-7ea5c011abe5'), . 05/21/2010 12:22:57.15 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 88jb Medium Feature Activation: Activating Feature 'RadEditorFeatureRichText' (ID: '747755cd-d060-4663-961c-9b0cc43724e9') at URL http://mmm-dev-ll/sites/Shoes/test. 05/21/2010 12:22:57.15 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 75fb Medium Calling 'FeatureActivated' method of SPFeatureReceiver for Feature 'RadEditorFeatureRichText' (ID: '747755cd-d060-4663-961c-9b0cc43724e9'). 05/21/2010 12:22:57.20 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 75f8 Medium Feature Activation: Feature 'RadEditorFeatureRichText' (ID: '747755cd-d060-4663-961c-9b0cc43724e9') was activated at URL http://mmm-dev-ll/sites/Shoes/test. 05/21/2010 12:22:57.51 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88yv Medium Creating default lists 05/21/2010 12:22:57.51 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72lp Medium Creating directory Lists 05/21/2010 12:22:57.51 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services Fields 88yz Medium Creating default modules at URL "http://mmm-dev-ll/sites/Shoes/test" 05/21/2010 12:22:57.51 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 8e27 Medium Ensuring module folder _catalogs/masterpage 05/21/2010 12:22:57.56 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72ix Medium Not enough information to determine a list for module "Default". Assuming no list for this module. 05/21/2010 12:22:57.87 w3wp.exe (0x1E40) 0x18A4 Windows SharePoint Services General 72h8 Medium Successfully applied template "SubSite#1" to web at URL "http://mmm-dev-ll/sites/Shoes/test". 05/21/2010 12:22:59.48 w3wp.exe (0x1E40) 0x0980 Windows SharePoint Services General 8e2s Medium Unknown SPRequest error occurred. More information: 0x80070057 05/21/2010 12:23:07.06 OWSTIMER.EXE (0x0884) 0x106C Office Server Setup and Upgrade 8u3j High Registry key value {SearchThrottled} was not found under registry hive {Software\Microsoft\Office Server\12.0}. Assuming search sku is not throttled. 05/21/2010 12:23:07.08 OWSTIMER.EXE (0x0884) 0x106C Search Server Common MS Search Administration 90gf Medium SQL: dbo.proc_MSS_PropagationGetQueryServers 05/21/2010 12:23:07.09 OWSTIMER.EXE (0x0884) 0x106C Search Server Common MS Search Administration 8wni High Resuming default catalog with reason 'GPR_PROPAGATION' for application 'SharedServices1'... 05/21/2010 12:23:07.11 OWSTIMER.EXE (0x0884) 0x106C Search Server Common MS Search Administration 8wnj High Resuming anchor text catalog with reason GPR_PROPAGATION' for application 'SharedServices1'... 05/21/2010 12:23:07.14 OWSTIMER.EXE (0x0884) 0x106C Search Server Common MS Search Administration 8dvl Medium Search application '3c6751cc-37b0-470a-bfa2-bfd0b5635fe1': Provision start addresses in default content source. 05/21/2010 12:23:07.15 OWSTIMER.EXE (0x0884) 0x106C Search Server Common MS Search Administration 7hmh High exception in SearchUpgradeProvisioner Keyword Config System.InvalidOperationException: jobServerSearchServiceInstance is null at Microsoft.Office.Server.Search.Administration.SearchUpgradeProvisioner..ctor(SearchServiceInstance searchServiceInstance) at Microsoft.Office.Server.Search.Administration.OSSPrimaryGathererProject.ProvisionContentSources() 05/21/2010 12:23:29.19 OWSTIMER.EXE (0x0884) 0x0FFC SharePoint Portal Server Business Data 79bv High Initiating BDC Cache Invalidation Check in AppDomain 'DefaultDomain' 05/21/2010 12:23:29.19 OWSTIMER.EXE (0x0884) 0x0FFC SharePoint Portal Server Business Data 79bx High Completed BDC Cache Invalidation Check in AppDomain 'DefaultDomain' 05/21/2010 12:23:45.84 OWSTIMER.EXE (0x0884) 0x08A8 SharePoint Portal Server SSO 8inc Medium In SSOService::Synch(), sso database conn string: 05/21/2010 12:23:50.80 OWSTIMER.EXE (0x0884) 0x0F14 Excel Services Excel Services Administration 8tqi Medium ExcelServerSharedWebApplication.Synchronize: Starting synchronize for instance of Excel Services in SSP 'SharedServices1'. 05/21/2010 12:23:50.80 OWSTIMER.EXE (0x0884) 0x0F14 Excel Services Excel Services Administration 8tqj Medium ExcelServerSharedWebApplication.Synchronize: Successfully synchronized instance of Excel Services in SSP 'SharedServices1'. 05/21/2010 12:23:52.31 w3wp.exe (0x1E40) 0x0980 SharePoint Portal Server Runtime 8gp7 Medium Topology cache updated. (AppDomain: /LM/W3SVC/1963195510/Root-1-129188762904047141)

  Read the article

• help me improve my sse yuv to rgb ssse3 code

  - by David McPaul

  Hello, I am looking to optimise some sse code I wrote for converting yuv to rgb (both planar and packed yuv functions). i am using SSSE3 at the moment but if there are useful functions from later sse versions thats ok. I am mainly interested in how I would work out processor stalls and the like. Anyone know of any tools that do static analysis of sse code? ; ; Copyright (C) 2009-2010 David McPaul ; ; All rights reserved. Distributed under the terms of the MIT License. ; ; A rather unoptimised set of ssse3 yuv to rgb converters ; does 8 pixels per loop ; inputer: ; reads 128 bits of yuv 8 bit data and puts ; the y values converted to 16 bit in xmm0 ; the u values converted to 16 bit and duplicated into xmm1 ; the v values converted to 16 bit and duplicated into xmm2 ; conversion: ; does the yuv to rgb conversion using 16 bit integer and the ; results are placed into the following registers as 8 bit clamped values ; r values in xmm3 ; g values in xmm4 ; b values in xmm5 ; outputer: ; writes out the rgba pixels as 8 bit values with 0 for alpha ; xmm6 used for scratch ; xmm7 used for scratch %macro cglobal 1 global _%1 %define %1 _%1 align 16 %1: %endmacro ; conversion code %macro yuv2rgbsse2 0 ; u = u - 128 ; v = v - 128 ; r = y + v + v >> 2 + v >> 3 + v >> 5 ; g = y - (u >> 2 + u >> 4 + u >> 5) - (v >> 1 + v >> 3 + v >> 4 + v >> 5) ; b = y + u + u >> 1 + u >> 2 + u >> 6 ; subtract 16 from y movdqa xmm7, [Const16] ; loads a constant using data cache (slower on first fetch but then cached) psubsw xmm0,xmm7 ; y = y - 16 ; subtract 128 from u and v movdqa xmm7, [Const128] ; loads a constant using data cache (slower on first fetch but then cached) psubsw xmm1,xmm7 ; u = u - 128 psubsw xmm2,xmm7 ; v = v - 128 ; load r,b with y movdqa xmm3,xmm0 ; r = y pshufd xmm5,xmm0, 0xE4 ; b = y ; r = y + v + v >> 2 + v >> 3 + v >> 5 paddsw xmm3, xmm2 ; add v to r movdqa xmm7, xmm1 ; move u to scratch pshufd xmm6, xmm2, 0xE4 ; move v to scratch psraw xmm6,2 ; divide v by 4 paddsw xmm3, xmm6 ; and add to r psraw xmm6,1 ; divide v by 2 paddsw xmm3, xmm6 ; and add to r psraw xmm6,2 ; divide v by 4 paddsw xmm3, xmm6 ; and add to r ; b = y + u + u >> 1 + u >> 2 + u >> 6 paddsw xmm5, xmm1 ; add u to b psraw xmm7,1 ; divide u by 2 paddsw xmm5, xmm7 ; and add to b psraw xmm7,1 ; divide u by 2 paddsw xmm5, xmm7 ; and add to b psraw xmm7,4 ; divide u by 32 paddsw xmm5, xmm7 ; and add to b ; g = y - u >> 2 - u >> 4 - u >> 5 - v >> 1 - v >> 3 - v >> 4 - v >> 5 movdqa xmm7,xmm2 ; move v to scratch pshufd xmm6,xmm1, 0xE4 ; move u to scratch movdqa xmm4,xmm0 ; g = y psraw xmm6,2 ; divide u by 4 psubsw xmm4,xmm6 ; subtract from g psraw xmm6,2 ; divide u by 4 psubsw xmm4,xmm6 ; subtract from g psraw xmm6,1 ; divide u by 2 psubsw xmm4,xmm6 ; subtract from g psraw xmm7,1 ; divide v by 2 psubsw xmm4,xmm7 ; subtract from g psraw xmm7,2 ; divide v by 4 psubsw xmm4,xmm7 ; subtract from g psraw xmm7,1 ; divide v by 2 psubsw xmm4,xmm7 ; subtract from g psraw xmm7,1 ; divide v by 2 psubsw xmm4,xmm7 ; subtract from g %endmacro ; outputer %macro rgba32sse2output 0 ; clamp values pxor xmm7,xmm7 packuswb xmm3,xmm7 ; clamp to 0,255 and pack R to 8 bit per pixel packuswb xmm4,xmm7 ; clamp to 0,255 and pack G to 8 bit per pixel packuswb xmm5,xmm7 ; clamp to 0,255 and pack B to 8 bit per pixel ; convert to bgra32 packed punpcklbw xmm5,xmm4 ; bgbgbgbgbgbgbgbg movdqa xmm0, xmm5 ; save bg values punpcklbw xmm3,xmm7 ; r0r0r0r0r0r0r0r0 punpcklwd xmm5,xmm3 ; lower half bgr0bgr0bgr0bgr0 punpckhwd xmm0,xmm3 ; upper half bgr0bgr0bgr0bgr0 ; write to output ptr movntdq [edi], xmm5 ; output first 4 pixels bypassing cache movntdq [edi+16], xmm0 ; output second 4 pixels bypassing cache %endmacro SECTION .data align=16 Const16 dw 16 dw 16 dw 16 dw 16 dw 16 dw 16 dw 16 dw 16 Const128 dw 128 dw 128 dw 128 dw 128 dw 128 dw 128 dw 128 dw 128 UMask db 0x01 db 0x80 db 0x01 db 0x80 db 0x05 db 0x80 db 0x05 db 0x80 db 0x09 db 0x80 db 0x09 db 0x80 db 0x0d db 0x80 db 0x0d db 0x80 VMask db 0x03 db 0x80 db 0x03 db 0x80 db 0x07 db 0x80 db 0x07 db 0x80 db 0x0b db 0x80 db 0x0b db 0x80 db 0x0f db 0x80 db 0x0f db 0x80 YMask db 0x00 db 0x80 db 0x02 db 0x80 db 0x04 db 0x80 db 0x06 db 0x80 db 0x08 db 0x80 db 0x0a db 0x80 db 0x0c db 0x80 db 0x0e db 0x80 ; void Convert_YUV422_RGBA32_SSSE3(void *fromPtr, void *toPtr, int width) width equ ebp+16 toPtr equ ebp+12 fromPtr equ ebp+8 ; void Convert_YUV420P_RGBA32_SSSE3(void *fromYPtr, void *fromUPtr, void *fromVPtr, void *toPtr, int width) width1 equ ebp+24 toPtr1 equ ebp+20 fromVPtr equ ebp+16 fromUPtr equ ebp+12 fromYPtr equ ebp+8 SECTION .text align=16 cglobal Convert_YUV422_RGBA32_SSSE3 ; reserve variables push ebp mov ebp, esp push edi push esi push ecx mov esi, [fromPtr] mov edi, [toPtr] mov ecx, [width] ; loop width / 8 times shr ecx,3 test ecx,ecx jng ENDLOOP REPEATLOOP: ; loop over width / 8 ; YUV422 packed inputer movdqa xmm0, [esi] ; should have yuyv yuyv yuyv yuyv pshufd xmm1, xmm0, 0xE4 ; copy to xmm1 movdqa xmm2, xmm0 ; copy to xmm2 ; extract both y giving y0y0 pshufb xmm0, [YMask] ; extract u and duplicate so each u in yuyv becomes u0u0 pshufb xmm1, [UMask] ; extract v and duplicate so each v in yuyv becomes v0v0 pshufb xmm2, [VMask] yuv2rgbsse2 rgba32sse2output ; endloop add edi,32 add esi,16 sub ecx, 1 ; apparently sub is better than dec jnz REPEATLOOP ENDLOOP: ; Cleanup pop ecx pop esi pop edi mov esp, ebp pop ebp ret cglobal Convert_YUV420P_RGBA32_SSSE3 ; reserve variables push ebp mov ebp, esp push edi push esi push ecx push eax push ebx mov esi, [fromYPtr] mov eax, [fromUPtr] mov ebx, [fromVPtr] mov edi, [toPtr1] mov ecx, [width1] ; loop width / 8 times shr ecx,3 test ecx,ecx jng ENDLOOP1 REPEATLOOP1: ; loop over width / 8 ; YUV420 Planar inputer movq xmm0, [esi] ; fetch 8 y values (8 bit) yyyyyyyy00000000 movd xmm1, [eax] ; fetch 4 u values (8 bit) uuuu000000000000 movd xmm2, [ebx] ; fetch 4 v values (8 bit) vvvv000000000000 ; extract y pxor xmm7,xmm7 ; 00000000000000000000000000000000 punpcklbw xmm0,xmm7 ; interleave xmm7 into xmm0 y0y0y0y0y0y0y0y0 ; extract u and duplicate so each becomes 0u0u punpcklbw xmm1,xmm7 ; interleave xmm7 into xmm1 u0u0u0u000000000 punpcklwd xmm1,xmm7 ; interleave again u000u000u000u000 pshuflw xmm1,xmm1, 0xA0 ; copy u values pshufhw xmm1,xmm1, 0xA0 ; to get u0u0 ; extract v punpcklbw xmm2,xmm7 ; interleave xmm7 into xmm1 v0v0v0v000000000 punpcklwd xmm2,xmm7 ; interleave again v000v000v000v000 pshuflw xmm2,xmm2, 0xA0 ; copy v values pshufhw xmm2,xmm2, 0xA0 ; to get v0v0 yuv2rgbsse2 rgba32sse2output ; endloop add edi,32 add esi,8 add eax,4 add ebx,4 sub ecx, 1 ; apparently sub is better than dec jnz REPEATLOOP1 ENDLOOP1: ; Cleanup pop ebx pop eax pop ecx pop esi pop edi mov esp, ebp pop ebp ret SECTION .note.GNU-stack noalloc noexec nowrite progbits

  Read the article

< Previous Page | 26 27 28 29 30