Search Results

Search found 981 results on 40 pages for 'sp3'.

Page 30/40 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• Usb device not working properly on a Thinkpad T60

  - by Xavierjazz

  I have just started getting a message that a USB device is not working properly. This is on a new Thinkpad T60 running Windows XP Professional SP3. I have had all devices attached for about 10 days or so. When I go to device manager there is no sign of a problem: everything is working correctly. I am unable to find out which device it is. I searched this forum but the only reference I found was to older computers which may not be Usb2 capable. This is not my problem. Any ideas? Thanks. EDIT: I realized I had a harddrive attached but turned off. Although I could not track down any error messages except the balloon that came up, I have disconnected it and, so far, no messages. We'll see over the next day or two, but this may be the problem. Thanks EDIT: This has not solved the problem. I get the message that one of the USB devices has malfunctioned and it points to "USB root hub (2 ports)" and shows an unused port and an unknown device. However, when I check my device manager, it says that there are no problems, everything is working as it should. ?? EDIT: I now found the event log view and there are 2 types of error messages. They do not relate to the time that I get the balloon. 2 of the 3 are "Ati2mtag" errors and the third is "System Control Manager". Are these related to my problem, and the balloon just pops up randomly? EDIT: well, I'm still having the problem, and have narrowed it down to a malfunctioning device. Thanks to all.

  Read the article

• Media Center - TV constantly pauses 1/2 second then plays 1 second

  - by Bob

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing. I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card, ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• Can't ping my Window 7 machine from within a Windows XP virtual machine

  - by Jonathan Conway

  I have Windows 7 installed as my primary operating system, on a laptop that's on my home network (wireless). I'm using Microsoft Virtual PC 2007 SP1 to run a virtual machine of Windows XP SP3, in which I want to access the Windows 7 instance, both to browse a shared folder and access the local Apache server. So far I can ping my Windows 7 IP address (IPv4) and access the apache server through the web browser through HTTP. However using my machine name never seems to work. Pinging it fails, and I can't access my apache server using it either. The problem seems to be something to do with my machine's name being registered under IPv6 rather than IPv4. I'm at a loss what to do. Should I try to set up IPv6 on the virtual machine? Not sure how to go about that. Or maybe I should somehow get my machine name on Windows 7 to work with IPv4? Although I think it already does, because I can ping it from a separate box (running Ubuntu), which is only registered under IPv6.

  Read the article

• Windows installation repair option not showing up

  - by Jason

  I'm trying to repair an existing Windows XP installation. Following the instructions from http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx this should work: - 1.When the Press any key to boot from CD message is displayed on your screen, press a key to start your computer from the Windows XP CD. - 2.Press ENTER when you see the message To setup Windows XP now, and then press ENTER displayed on the Welcome to Setup screen. - 3.Do not choose the option to press R to use the Recovery Console. - 4.In the Windows XP Licensing Agreement, press F8 to agree to the license agreement. - 5.Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP. - 6.Follow the instructions on the screen to complete Setup. On step 5 pressing R does nothing and there is nothing on the screen saying it would. When I just select to install I get a message that a previous installation is there and proceeding will destroy it and installed applications, I can optionally select a directory other than c:/windows, and I can optionally format before continuing. I had tried to go from SP2-SP3. It failed, and then I couldn't get to Safe Mode. I put the SP1 disk back in to do a repair, and I don't see that option. (I don't have an SP2 boot/install disk, I just have the non-boot upgrade package.)

  Read the article

• Physical-to-virtual for personal use

  - by Journeyman Geek

  One of my current projects involves reducing the number of old computers lying around. So far, the office systems have been downsized from 5 to 2. One system which had no data on it was dumped entirely, while three other identical boxes were consolidated into to one (I swap hard drives as needed and they just work(tm)). I want to make further cuts. The physical systems in question all run windows xp sp3, and were old Pentium 4s with 256 MB of RAM. Currently, I have got a VirtualBox running on another system. My intention is to migrate all services to that. We can assume that disk space and RAM on the host is not an issue. I'd rather not go with a client-server physical-to-virtual (P2V) method like what VirtualBox uses now. I have a few specific concerns as well - specifically whether I'd need to reactivate or sysprep for dissimilar hardware first. An offline tool for imaging (Windows or Linux) would not be an issue since the drives could be mounted onto another system I have anyway or I could use a LiveCD. What would be my options for P2V conversion, and what would I need to keep in mind when doing this?

  Read the article

• Page pool memory

  - by legiwei

  I'm currently using Windows XP SP3 32 bit, using C2D E6320 with 2GB RAM. When I am playing Starcraft 2, I encounter an error where it says my system is running low on page pool memory. Starcraft graphic settings suggested a high settings for me. I do not think it has to do with my GC but with my RAM. I then made a search to try to rectify the problem. Apparently, it's something to do with my virtual memory. I then proceed to try to the suggested solution which is to temper the registry and limit the page pool memory to 384MB. However, having done so, I still could not achieved it. I've seen screenshot settings of windows XP with 2GB having 384MB of page pool memory. My default settings puts it at 195MB whereas when I try to increase the pool limit, it can only go to a max of 229MB. I tried increasing my RAM capacity to 3GB but the pool limit still remains. I like to know how to increase my page pool memory. I've tried searching for solution but to no avail other than the one that I've mentioned above (which didn't solve my problem completely).

  Read the article

• What are "Excess Fragments" in defragmenting a hard drive?

  - by Andrew Swift

  I'm defragmenting my hard drive (XP SP3) with PerfectDisk 7.0, and it finds 816,659 excess fragments when I ask for an analysis. [update] Specifically, it shows that the 1TB disk is 14% fragmented with 19693 fragments and 816,659 excess fragments. About 20% of the disk is still free space. What does excess fragments refer to? What is the difference between fragments and excess fragments? I have had problems in the past where I defragmented a fragmented disk and many files were corrupted. It seemed as though "excess fragments" referred to orphan pieces, where the program couldn't find out where to put them. If that was true, then defragmenting a disk resulted in many incomplete files, and in fact I defragmented a disk full of MP3's and got a lot of corrupted files as a result. Instead, I started to simply format a separate disk and copy everything from one to the other. That way there were no orphan bits, and no file corruption. Does anybody know what "excess fragments" really are?

  Read the article

• Virus / Malware: Explorer window with strange user logged into Hotmail

  - by abel

  I was looking into a PC, the user of which had complained that he couldn't connect to the internet and that the PC was experiencing random restarts. The PC runs WinXP SP3. On examination, I found that the Wireless Zero Configuration service was stopped. I enabled that and the internet was back on(The pc connected through wifi). Then I started firefox and browsed to gmail.com. I did not launch any other program, except for a few explorer windows. It was then I noticed a window had popped up(it was not a pop up). It had the explorer folder icon and instead of explorer folder contents, it showed a hotmail page, with a user named "Homer Stinson" logged in. The titlebar was empty and there were no toolbars. I asked the client whether this was his email id, which he said it was not. I opened task manager, which did not show this explorer window in it's Application tab. I switched back to the 'rogue' window and found that the hotmail settings page was now open, which later changed to the hotmail edit profile page for the same user. I was not clicking anything. Then suddenly the window closed. I checked the autorun locations, fired up a Malwarebytes Anti Malware scan which gave a clean result. The system also had an updated installation of AVG. I don't want a solution for this virus(?) problem. I asked this here because I wanted to know if somebody has come across something similar. What kind of malware can this be? The user had not seen a similar window before and I should have taken screenshots. (PS:Homer Stinson is an imaginary name. I searched for the other real name with some relevant keywords but could not come up with a virus/malware discussion post.) UPDATE: When I checked the PC later a DEP error had popped up closing which restarted the PC.

  Read the article

• It takes a long time until Windows XP recognize I connected USB drive

  - by Pavol G

  I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognizes it and shows it as a new disk. I can also see (disk's LED is blinking) that something is scanning the disk when I connect it; when this is done Windows immediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using Spybot), also tried running Windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Edit: I tried to update to SP3 - no change Edit2: When this "strange" scanning occurs I can see that DPCs process is taking about 50% of CPU. When the scan ends (after 5min) this process take 0% again. Edit3: About the scan time, currently it's taking about 5min, but this time is growing as I'm adding more data to the disk, currently its about 40GB and I don't want to see how long it will take with 1000GB. Thanks a lot for every advice!

  Read the article

• Hard Drive benchmark values show write very very slow

  - by John

  I recently started to have issues with my laptop being very slow. I ran a hard drive benchmarking tool (by ATTO) that showed that the write speed was very very slow on my boot drive. I ran the same benchmark on my usb drive and it was 650 times faster than my boot drive when it came to writing. Reading is very fast/normal on both. I swapped out an identical drive and ran the same benchmark. This time the drive showed proper write speed. Thinking that I had a hard drive going bad I cloned the old one onto the new one. I managed to clone the problem too. Anyone have any ideas on what in WinXP SP3 might be causing the write issues? I am on a corporate network and we have commercial anti-virus software installed. (AVG I think) I regularly run defraggler and have about 40 gig free on a 100 gig drive. The machine has 4 gigs of memory. Any ideas? TIA J

  Read the article

• IIS 6 + ASP.NET web service - DW20 and stackoverflow exception

  - by pcampbell

  Consider an ASP.NET SOAP web service that starts up fine, but craters hard when receiving its first hit. Please note that this is deployment works in the Test environment, but not in the PreProd environment. Both are Windows 2003 SP3 + IIS 6 + ASP.NET 3.5. All up-to-date. The behaviour that we're seeing is: restart the site & app pool the app pool is configured to run under Network Service. browsing to the .asmx and .wsdl responds normally, as expected. send a normal well-formed SOAP request / normal payload to the web service 100% CPU usage after 5 seconds, the page request / site returns "Service Unavailable" no entry is created in the IIS log file (i.e. c:\windows\system32\logfiles\W3C-foo) the app pool ends up being stopped The processes that hit the CPU hard are dw20.exe. I am unsure why Dr Watson is involved here. Event Log shows an ASP.NET Runtime error: Task Manager: Event log text: EventType clr20r3, P1 w3wp.exe, P2 6.0.3790.3959, P3 45d6968e, P4 errormanagement, P5 1.0.0.0, P6 4b86a13f, P7 24, P8 0, P9 system.stackoverflowexception, P10 NIL. Questions Any thoughts on what this system.stackoverflow exception might be? Given that the code is the same between environments, might it be a payload problem? Could it be a configuration issue? You can see the name of my .NET assembly there in the exception message: "ErrorManagement"

  Read the article

• VMware and Windows Activation

  - by Peter M

  Yesterday I installed Slysoft's Virtual CloneDrive in order to mount an iso for some software installation on my host system (XP Pro SP3) This morning I fired up VMware and made a linked clone of an existing XP vm in order to do some software testing. This is the sort of thing that I do all the time, and the base XP vm that I clone was activated a long long time ago. The surprise today was that the newly cloned vm was no longer activated and XP cited major changes in hardware as the reason. I repeated the test with a full clone of the base system and got the same message. I then started up my base vm and it seemed to be activated, yet another vm (which I fully cloned from the base vm a long time ago) now started reporting that XP was not activated. At this point I guessed that Virtual DriveClone might have been the source of my hardware differences so I uninstalled it and rebooted. After this I made a new linked clone and full clone of the base vm and XP did not complain about not being activated. So I seem to be back to where I was before installing Virtual DriveClone with the exception that that one particular XP vm continues to complain about activation (even though 4 or 5 other XP vm's are fat and happy) Now to my questions: Why would adding Virtual CloneDrive to the host system affect XP activation on the vm's? From their point of view I would have thought that the environment had not changed as I had not enabled any new hard drives in their systems. Or is adding a hard drive to the host system enough to upset XP activation? Since this event, one of my fully cloned vm's is still reporting that XP is not activated even though I have removed Virtual CloneDrive. Is there anyway to convince XP that it is on the same system as yesterday? Or are my only options to do an activation or restore the vm from a previous backup?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• DPM 2007 clashing with existing SQL backup job

  - by Paul D'Ambra

  I've recently installed a DPM2007 server on Server 2003 and have set up a protection group against a server 2003 server running SQL 2005 SP3. The SQL server in question has a full backup (as a sql agent job) once a day and transaction log backups hourly. These are zipped up and FTP'd to a server offsite by a scheduled task. Since adding the DPM job I'm receiving many error messages: DPM tried to do a SQL log backup, either as part of a backup job or a recovery to latest point in time job. The SQL log backup job has detected a discontinuity in the SQL log chain for database SERVER_NAME\DB_Name since the last backup. All incremental backup jobs will fail until an express full backup runs. My google-fu suggests that I need to change the full backup my sqlagent job is running to a copy_only job. But I think this means that I can't use that backup with the transaction_logs to restore the database if the building (including the DPM server) burns down. I'm sure I'm missing something obvious and thought I'd see what the hivemind suggests. It is an option to set-up a co-located DPM server elsewhere and have DPM stream the backup but that's obviously more expensive than the current set up. Many thanks in advance

  Read the article

• Why are Microsoft Windows Update taking so long to install?

  - by Mathieu Pagé

  Hi, I have a question that is not related to a problem I have. Just something I'd like to understand. Why are Windows update so long? First Windows Update need to find witch updates you needs and this take about 5 minutes. What is happening behind the scene during those 5 minutes? I would have tought that it would be enough to compare the updates you already have to the complete list of updates or to check the version numbers of a couples files. Then when it comes time to install the upgrades, they're also taking a long time. Some 1 Mb updates takes 2, 3 or 5 minutes to install. What is taking so long. I would have though that it was simply a mater of backup the old file, uncompress the new files, replace the old file. This should be really fast. Is Windows doing something else? For comparison, under Linux, you can find which updates you need in about 20 seconds and installing them is usually pretty fast (The time to uncompress the files). I can do a complete updgrade of my linux machine in about 25 minutes (download 600-800 Mb of updates, hundreds of them and install them) while under windows 25 minutes is the time it needs to find witch update are needed and install about 5-10 updates. I just updated a Windows XP home from SP1a to SP3 + all other updates. It took me more than 3 hours. Doing something like that in the Linux World takes about 30 minutes. I don't want to bash Microsoft here. I genuinly want to know what they do differently that makes it so long.

  Read the article

• Default Browser hangs (IE, Chrome)

  - by Craig Hinrichs

  IE was my default browser about three months ago when I started experiencing this issue. Intermittent hangs would occur when I would open a new main page or new tab to a site I know would be up. What I mean by a hang: The browser would open and say "Waiting for site " and do nothing more. If I closed the window and reopened it it would immediatly connect. Over time I would have to close and reopen the window to get to the page. This would happen to any page including Google. I finally got sick of it and started using chrome and I will never go back. I recently upgraded my anti-virus and now I am experiencing the same issue with Chrome. I use AVG for my antivirus. Empirically it seems if I don't make Chrome my default browser I don't experience the issue. I tested this theory for over two hours yesterday. Possible issues I have found this coudl be but not confirmed yet: MTU settings are not correct. I am infected but my antivirus has not caught it (unlikely but possible) ?? I would like to think this is related to my antivirus but I am unsure how to verify. I don't like the idea of killing my antivirus if #2 is a possibility. I am looking for tips on how I can trouble shoot possible issues. I am on Windows XP SP3 Thanks in advance.

  Read the article

• Photoshop CS6 Corrupted File recovery

  - by Ben Franchuk

  Last night I was working on a client application mock-up in photoshop, but was goin to take a break from my work so I saved the .PSD file on my internal HDD and put my computer into stand-by mode once the file had finished saving. Unfortunately my computer crashed while it was entering stand-by and shut itself down (photoshop was still open). I did not boot it again to make sure all my files were ok because they had already been saved, but today once I opened up the file again it was extremely corrupted and also completely un-editable (screenshot bellow). so what im asking is there any way to recover my work, or at least some of it? i have put in a good few days work on this project and would hate to have to restart it. the size of the file is 3070 KB, even though it reads as 712 KB in photoshop. i dont know if these file sizes are larger or either smaller than the original non-corrupted file's size, but considering all the layers in the file i suspect it was larger before it corrupted. im using windows XP professional 32bit SP3. both my OS and said .PSD file are located on the same internal HDD (74.4 GB). i do have an external HDD (1.5 TB) but i primarily only use it for movies music and tv shows. i dont know if it was plugged in t the time of me editing the document last, though, if it means anything. i have tried many image and PSd recovery softwares but none have returned any results that may help recover my work. edit: i tried using a photo reccovery software (odboso Photorecovery) that actually seems to recover the corrupted file in question judging by the size of the file, but i cannot recover it because of the licence fee. knowing that the file is still likely on my HDD, what location might it be located?

  Read the article

• Error - "IR Hardware not detected" - but it's installed/working

  - by Robert

  I am trying to do: Settings-TV-Set up TV signal. During this process I am getting the error "IR Hardware not detected." With the remote, I can select the "try again" button (to re-detect) and it tries again, so the remote works. Plugging in the "IR blaster" doesn't change anything. (I wouldn't expect any difference, but I read a post which said you needed that. I will get Media Center to change channels if I can get that working - but first things first.) I was able to do the setup months ago when I had cable. and everything was fine. I just got DirecTV. (BTW - During the above process, Media Center detects the signal coming in on channel 3. Windows XP Media Center SP3. The TV Tuner card is a Pinnacle TCTV HD PCI. Everything - and I mean everything - has the latest firmware and drivers - as of 4 months ago when I fixed a different problem. So I DON"T WANT TO HEAR the standard answer to check drivers/firmware. THANK YOU.) Thanks for any help.

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• Valid IP address but can't surf without rebooting

  - by Kat

  I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >