Search Results

Search found 3293 results on 132 pages for 'vmware workstation'.

Page 30/132 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

• faking NAT with a VMware distributed switch across multiple hosts

  - by romant

  I need to construct a NAT for certain machines within the network. Wish to do this with dvSwitch - as it seems the logical way of attacking the problem as in this scenario there's just under 30 hosts. In order for the NAT'ed VM's to have access to the 'real' network. I am providing a 'router' VM, which will have access to the WAN/outside network, and also act as the DHCP server for the NAT'ed machines. Problem Space When the machines connected to the NAT interface and the router are on the same host, then they get an IP from the router VM, and work perfectly (routed outside). Unfortunately machines on other Hosts that are connected to the dvSwitch do not get an IP and further tcpdump shows no network data getting through across the hosts within the dvSwitch. Has anyone achieved a NAT solution using a dvSwitch before that they could share?! Thank you. EDIT: Including the diagram.

  Read the article

• ESXi configuration

  - by Simone Falcini

  I just bought a dedicated server on online.net I have a public and a private ip. I installed esxi from their panel and I can connect successfully with my vsphere client. The problem is this: I want to create some instances and I want to give them different private ips. I also want to create some NAT rules to forward all users coming to my public ip port 80 to a specific instance. How can I do that? Thanks

  Read the article

• Why do I have to manually 'Restart Management Network' on vSphere 5 host after reboot to get networking available?

  - by growse

  I've got a couple of vSphere 5.0 hosts in a small lab environment here and I've noticed a strange behaviour. When on of the hosts gets rebooted, it is unresponsive to the network until I log into the ESX console, Press F2 to customize and select Restart management network. Once this is done, the networking works perfectly as expected. Each host has two NICs which are trunked together using Etherchannel to a Cisco 3750. The link is also a .1q VLAN trunk and the management network is configured on VLAN121 with the VM traffic configured on VLAN118. Why would the host be completely dead to the world until I physically kick it? Edit Sample switch config for trunk: interface Port-channel2 description Blade 1 EtherChannel Trunk switchport trunk encapsulation dot1q switchport mode trunk end ! ! interface GigabitEthernet4/0/1 description Bladecenter1 CPM 1A switchport trunk encapsulation dot1q switchport mode trunk speed 1000 duplex full channel-group 2 mode on end Vswitch teaming settings: Management port group settings:

  Read the article

• Virtual Machine Library not updating

  - by jeremyyip

  Hi, I have a problem with my library window. I use to have a XP VM, which I deleted and now have a Vista VM. Every time I start Fusion, the XP VM shortcut will still be in the library (File not found), and the Vista VM won't be. I have tried re-installing Fusion but the same XP shortcut keeps coming up. Fusion doesn't seem to be updating the list of VM I currently have for some reason. Any ideas? Lots of thanks Jeremy

  Read the article

• Has anyone achieved true differential sync with rsync in ESXi?

  - by Julius

  Berate me later on the fact that I'm using the service console to do anything in ESXi... I've got a working rsync binary (v3.0.4) that I can use in ESXi 4.1U1. I tend to use rsync over cp when copying VM's or backups from one local datastore to another local datastore. I've used rsync to copy data from one ESXi box to another but that was just for small files. In now trying to do true differential syncs of backups taken via ghettoVCB between my primary ESXi machine and a secondary one. But even when I do this locally (one datastore to another datastore on the same ESXi machine) rsync appears to copy the files in their entirety. I've got two VMDK's totally 80GB in size, and rsync still takes anywhere between 1 and 2 hours but the VMDK's aren't growing that much daily. Below is the rsync command I'm executing. I am copying locally because ultimately these files will get copied onto a datastore created from a LUN on a remote system. Its not an rsync that'll be serviced by an rsync daemon on a remote system. rsync -avPSI VMBACKUP_2011-06-10_02-27-56/* VMBACKUP_2011-06-01_06-37-11/ --stats --itemize-changes --existing --modify-window=2 --no-whole-file sending incremental file list >f..t...... VM-flat.vmdk 42949672960 100% 15.06MB/s 0:45:20 (xfer#1, to-check=5/6) >f..t...... VM.vmdk 556 100% 4.24kB/s 0:00:00 (xfer#2, to-check=4/6) >f..t...... VM.vmx 3327 100% 25.19kB/s 0:00:00 (xfer#3, to-check=3/6) >f..t...... VM_1-flat.vmdk 42949672960 100% 12.19MB/s 0:56:01 (xfer#4, to-check=2/6) >f..t...... VM_1.vmdk 558 100% 2.51kB/s 0:00:00 (xfer#5, to-check=1/6) >f..t...... STATUS.ok 30 100% 0.02kB/s 0:00:01 (xfer#6, to-check=0/6) Number of files: 6 Number of files transferred: 6 Total file size: 85899350391 bytes Total transferred file size: 85899350391 bytes Literal data: 2429682778 bytes Matched data: 83469667613 bytes File list size: 129 File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 2432530094 Total bytes received: 5243054 sent 2432530094 bytes received 5243054 bytes 295648.92 bytes/sec total size is 85899350391 speedup is 35.24 Is this because ESXi is itself making so many changes to the VMDK's that as far as rsync is concerned the entire file has to be retransmitted? Has anyone actually achieved actual diff sync with ESXi?

  Read the article

• how to activate windows twice in vmware fusion

  - by durkadurka

  I have windows 7 (professional OEM) installed in bootcamp. Not thinking about it, I activated it running in fusion. now in fusion everything is fine, but when i run it directly it says it needs activation. I read that one actually needs to activate it directly first, and afterwards in fusion. How can I fix this situation?

  Read the article

• LUNs disappear after rebooting the ESX/ESXi host

  - by mariolos

  A single LUN among from a group disappeared. Neither the host nor the Vcenter can see it. Four virtual machines on the LUN now are unknown. The strange thing is the LUN is now available in the list when you try to ADD datastore from configuration == storage == Add Datastore But this cannot help me since i need the vms on the lun and i do not get options to add the lun without formating it to VMFS How can i get the lun back or atleast be able to copy the vms from it

  Read the article

• ESX Install........

  - by ov4

  HI all, I recently purchases a bunch of r710 from dell, i installed esx on it. the installation process finished without a problem. however once the esx boot the following error displays at the botton with red letters 00:00:02:21.493 cpu11:4119) mod:2971: Initialization for vmfs2 failed with -1 i installed on two different servers and the same error pops up. the curius thing is that if i install esxi 3.5 or 4 there is not problem help Thanks Oscar

  Read the article

• VMWare and ALT GR key results in missing characters

  - by donat

  For some odd reason WMware products hijack the AltGy-key despite I make sure that other keys are used as hot keys to release mouse and keyboard from the virtual machine. While this is not a problem for US keyboards, european however who extensively use AltGR for characters such as pipe (|), at-sign (@), left brace ({) and right brace (}). This seem to happen both in Windows and Linux and I can not seem to find a solution that works for both. :( Anyone have an idea how to fix this without the need to modify the guest OS every time? Thank you.

  Read the article

• Using VMware Guest OS to enable Host OS to ssh to remote network

  - by Reuben L.

  Basically I have an issue because my host OS is 64-bit Linux Mint (Ubuntu derived) and it doesn't seem to be compatible with the Juniper Network Connect that is used by the network at my workplace. Thus, I am unable to ssh from terminal to the network. I can't make changes to the workplace network either so that leaves me with looking for solutions on my end. The main reason for me to access the network from home is to check on my running processes or to issue more commands to a few workstations. Putty is the desperate choice I usually make but it means I have to reboot to Windows and also have limited control. I've tried several other methods and they have all failed. Recently, I setup a VM with Windows 7 as the guest OS. Now half my problems are fixed as I don't have to physically reboot the system - I just have to engage Juniper Network Connect on the VM. However, I would still like to use my Linux terminal to ssh to the network. It sounds plausible that I could somehow manipulate ports to connect to the remote network from the host OS tunneled through the guest OS, but I really have no clue how to do so... Can anyone help?

  Read the article

• RHEL raw device (over VMware RDM) performance issues

  - by jifa

  I'm running RHEL 5.3 over vSphere 4.0U1. I configured multiple LUNs on my NetApp (Fibre) storage, and added the RDM on two (Linux) VMs, using the Paravirtual SCSI adapter. One LUN is 100GB in size, successfully mapped to /dev/sdb on both VMs, 5 more are 500MB in size (mapped to /dev/sd{c-g}. I also created one partition per device. I have encountered two issues: First, writing directly to /dev/sdb1 gives me ~50MB/s, while any of the /dev/sd{c-g}1 gives me ~9MB/s. There is no difference in configuration of the LUNs apart from their size. I am wondering what causes this but this is not my main problem, as I would settle for 9 MB/s. I created raw devices using udev pretty straightforwardly: ACTION=="add", KERNEL=="sdb1", RUN+="/bin/raw /dev/raw/raw1 %N" per device Writing to any of the new raw devices dramatically slows down performance to just over 900KB/s. Can anyone point me in a helpful direction? Thanks in advance, -- jifa

  Read the article

• Vmware cpu allocation for a spiking database server

  - by user1552172

  I have a database server with many poorly written queries that causes the sql server to spike then drop constantly ( a massive start from scratch is happening). I need to know if the cpu allocation on the vm to expand as needed is best practice for a case like this. I am wondering if the esxi platform cant expand as fast as the spikes happen. I am curious what is best practice for vm cpu allocation on sql server (with horribly written queries)

  Read the article

• ESXi 5 VM Putty session hangs, vSphere client timing out

  - by user192702

  First of all I believe this is a ESXi issue but let me know if you have seen this. It started about a year ago when I noticed occasionally when I putty via SSH to my VM guests, if I do anything that makes it to display a lot of things at once, the session will hang and I have to start a new one quite often only to find the same behaviour. What I meant by display a lot of things can be any of the following: 1) tail -f filename 2) Paste a long command 3) less filename If I type in one character at a time this won't happen. I tried searching online and it always point me to flow control settings and the various suggestions I've tried have never been able to resolve the issue. Since last week, I've noticed I'm not able to connect to my POP3 server from Outlook (it's timing out from Outlook's perspective). Today I tried to connect to the ESXi via vSphere client and it gives me a time out also. Exact behavior and error I saw is similar to the one posted at the following URL but the suggested technique also failed to resolve the issue. http://davidcocke.blogspot.hk/2012/02/unable-to-login-with-vsphere-client.html Has anyone experienced this before? Any suggestions on how to troubleshoot this?

  Read the article

• VMWare ESX installation on sata disk

  - by ilansch

  I have a PC with Gigabyte H77 motherboard with Intel I5-3550 CPU 8 GB RAM 1600MHz and a 500GB Harddisk (7200RPM) - WD Sata III disk I wish to install esx on it and run some virtual machines on it. not alot, something like 2-3 VMs. My hardisk is Sata, is it possible to install ESX Server on it ? I am not worried about loading issues. When i try loading the installation it writes it cannot detect my disk (since its not SCSI disk). How can i bypass this ? or find a solution. thanks

  Read the article

• VMware 1.0.1 Windows7 - Ubuntu hostnames

  - by Kyle K

  I'm trying to run Ubuntu as the guest OS using VMWware 1.0.10 with Windows 7 Ultimate as the host OS. I had this set up previously with Win XP as the host OS and in fact I'm using the same .vmx My problem is I can't get either Win7 or Ubuntu to be able to ping the other by hostname. After installing Samba and Winbind on Ubuntu, I was able to get this working when under WinXP, but for some reason I can't get it to work under Win7. I can ping by IP Address, and the guest OS even shows up by hostname under the Windows networking panel (but of course I can't do anything with it), but pinging using short hostnames just won't work. Also, Win7 firewall is turned off completely.

  Read the article

• vSphere - datastore falling off a host

  - by Chadddada

  Recently we have been running the vCheck powershell script daily in order to help in monitoring our vSphere ESX 4.0 environment. One of the oddities that we have been seeing is that some of the datastores on the SAN don't always show up on every host. Our hosts are connected redundantly, via FC, to some brocade FC switches, which then connect via fiber to our EMC Ax4 SAN. While all the datastores are presented to each host we have, and they see them initially, they sometimes seem to fall off and are no longer visible. It easy enough to rescan for datastores and add them back to the hosts the hosts but this seems to be an error. Has anyone else seen this or know why it may be happening? Responses to questions: 1. Is it always the same ESX servers that lose their connection? – Scott Warren No this happens randomly on random hosts. If a VM is running on a particular host, of which the VM's disks are on a SAN datastore, then that datastore won't disappear. It seems to happen if a host doesn't touch a datastore for a bit and it just forgets about it.

  Read the article

• How can I shut down all my Virtual Machines when my UPS kicks in?

  - by Tim

  I have a Dell T610 running ESXi4, an APC Smart UPS 1000VA and a local "console" machine running Vista and the vSphere 4 Essentials pack. A dedicated management network is in place between the T610 and the Vista machine. We have 4 VMs: SBS 2003, Server 2003 running Terminal Services, and two XP Machines. Ideally, when the UPS is forced to use battery power [for a set number minutes], I would like to gracefully shutdown all the VMs, then the ESXi, then the console machine. The latter two are not strictly a priority, but the VMs within ESXi are. Google provided lots of deprecated scripts that used to work on ESXi 3.x or similar, however I am unable to find what they were deprecated by. What do I need to be able to do this? I have Powerchute Express as supplied with the UPS, but would be willing to pay for software if required.

  Read the article

• Is there a faster way to deploy an OVA template?

  - by Luke

  I need to deploy vSphere Server Appliance 5.1. I have vSphere Client running locally and my internet upload is capped at 3 Mbps. It says it's going to take about 200 minutes to upload. When selecting a URL as opposed to a local file, does vSphere Client download it locally and then upload, or does it download the OVA directly to the server? My goal is to avoid waiting 3 1/2 hours for this to upload. If specifying a URL isn't any faster, are there any other methods that would allow me to deploy from the datacenter instead of my office? We don't have any Windows VM's installed on our cluster. So unfortunately I don't have a Windows machine with faster upload speed.

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• ESXi5 - management services crashes - vms running

  - by Frederik Nielsen

  I have a setup with two ESXi5 servers. We are(were) running with a ISCSi box to server disk for the VM's - however we are in the progress of migrating away from it, because the storage os disk is bad. Now, one of the ESXi hosts has been running for ~20hrs, and it seems like the management services just crashed on that host.. The vms are still running - so it's not really serious. However, I want to fix it. Should I be worried? Will the VM's keep running? The hosts does respond on pings. I am running a vcenter to administrate the hosts. Thanks in advance.

  Read the article

• ESXi settings lost following reboot

  - by Araz

  Hi All, I have freshly installed ESXI 4. But when ever i reboot my server all the setting gets lost like IP setting move back to automatic instead of static, the license key gets lost. Any ideas?

  Read the article

• migrating storage to a different controller

  - by bellocarico

  Hello, I've just purcheased a couple of adaptec controller (2405/5405) for my ESXi 4.0 U1 servers. Currently ESXi and a couple of VMs are hosted on single sata boot disk connected to a nvidia on board non-RAID controller. I know that it's possible to migrate from single disk to RAID 1 with adaptec and I'm pleased with that, but I'm not sure if ESXi has already the right drivers installed/loaded for this controller. Is there any way I can check this? Is ESXi clever enough to recognize the new hardware and load the right module? Thanks

  Read the article

• Shrinking physical volumes in LVM on a Linux Guest in ESXi 5.0

  - by Stew

  The problem: Linux guest (OpenSuse 12.1), with multiple virtual disks attached. 3 disks are in a logical volume, two of which are exactly 2TB. None of the disks are independent, and due to the backup software we use, cannot be independent. When the two 2TB virtual disks are "dependent", the snapshot fails stating that the file is too large for the datastore. When I put those two disks in independent mode, snapshots work fine (the other disk is 1.8TB). I have therefore concluded that even shrinking the two physical disks by 100GB should solve the problem, however I am having trouble conceptualizing how to go about getting those disks smaller without breaking the LVM entirely. The actual LV has 1.3TB free, so there is plenty of space to shrink with. What I need to accomplish: Deallocate 100GB from the two, 2TB virtual disks within the linux guest. Shrink the two virtual disks by 100GB within vsphere (not as complicated). Are there any vsphere/LVM gurus that can give me a clue?

  Read the article

• Sending eMails in a external subnet in vmware ESXi

  - by user80658

  This might be a bit hard for me to explain - and it is a pretty individual situation. I got a native server at Hetzner (www.hetzner.de). The public IP is 88.[...].12. I got ESXi running on this server. I can access the esxi console by the public ip, but none of the virtual machines. That's why I bought a public subnet with 8 (6 usable) IPs (46.[...]) and an additional public ip (88.[...].26). This additional public ip belongs to the first virtual maschine - a firewall appliance - which is connected to the WAN. This need to be done this way - since it is the official way by hetzner. My 46. subnet is behind the firewall. I got a virtualmin server with dovecot imap/pop3 server. When sending a email, most provider (gmail) will accept those mails, but a lot will put it into spam (aol). My theory is: The MX line of my domain says of course the ip of the virtual machine (46.[...]), but in the raw email it says that email is sent by the ip of the firewall (88.[...].26), which doesnt sound trustworthy. A solution would be if the firewall could handle mail, but it simply cant. How can I prevent this problem? Thanks.

  Read the article

• How can I automate restarting a vmware vm

  - by Stu

  I have a vm that does nothing but run magic jack. Magic jack doesn't run perfectly in a vm. It works great for days then randomly the vm reboots. except it doesn't come up clean. It gets to the windows splash screen and hangs spinning the cpu. I don't care how I solve the problem (although not crashing in the first place would be ideal) but I just need the vm to reboot cleanly when it does crash. Is there a windows registry setting I can say "on crash, reboot" or something like that?

  Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >