Search Results

Search found 1298 results on 52 pages for 'workstation'.

Page 30/52 | < Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >

  • Allow VMWare client to connect only via VPN

    - by Frank Meulenaar
    I have a VMWare (currently using Workstation on Vista, but thinking about switching to ESX) client with Windows XP. I've installed OpenVPN in the client and it connects to the corporate VPN server. I want to make sure that all traffic from the Windows XP machine goes trough this VPN tunnel, but I can't change any settings on the corporate VPN server. Is it possible to restrict the internet connectivity of the Windows XP client in such a way that it can only send packets to the IP of the corporate VPN server? In that way it'd be impossible for packets to bypass the tunnel. I've looked at NAT configurations but couldn't see how I could make this setup.

    Read the article

  • SolidWorks ratio issue with printing in landscape

    - by jamiemmp
    We run SolidWorks 2010 on XP. On one workstation when printing to the plotter in a 1:1 ratio in landscape mode it's off by small increments. He needs to adjust manually from 1:1 to 1:1.009 (for example) in order to correctly print 1:1. The increments by which it's off varies from drawing to drawing. None of the other workstations have this issue. All five of the workstations have the same settings and all print to one networked plotter. Three out of five have the same graphics card. Scale to fit is not checked. I read this site often, but this is the first time I've posted. I'm hoping someone here has run across this before. Thanks.

    Read the article

  • Network printer - Print direct or via shared printer on Server?

    - by NickC
    It has occurred to me that a workstation can connect to a printer in two ways: 1). Printing directly to the IP of the printer with the print driver installed locally. 2). Printing to a \Server\Printer1 share with the print queue residing on the server. Question is which way is preferred? I would assume that printing directly to a network printer rather than going through the server would be the most efficient from the point of view of network traffic. On the other hand I guess a server printer share would be easier to manage with the correct driver automatically being downloaded to the workstations. Also what about using GPP (Server2012) to install this printer on the workstations, does that require any specific way?

    Read the article

  • Transfer files using ssh

    - by zozo
    Good day to all. I am using ssh (winSCP) to transfer some files from a server to my workstation. The problem is that at some files I get disconnected. Always same files. I am the owner of the directory so I guess the file permissions is not a problem. (Also I set the permissions to 777). Is there a size limit or something like that? Thank you for your time. Protocol is SFTP, server is 32bit machine. Files are 100MB tops. Added: Worked with filezilla using ftp. This temporarily fix the problem but is not exactly a solution since maybe next time I won't have root access to create a ftp account

    Read the article

  • ft_stopword_file not picked up

    - by Alex Holsgrove
    I have a VPS server with a company called Webfusion. I want to remove some or all of the FULLTEXT stopwords because some specific words needs to be searchable with my DB content. I opened /etc/mysql/my.cnf and added the line ft_stopword_file="". I restarted the mysql service, ran a repair table and then tried my MATCH query with no success. I ran SHOW VARIABLES LIKE 'ft_%' and it simply shows (built-in) next to the stopword file. I am running WAMP on my workstation, and whilst I realise this isn't configured the same as a commercial VPS, the above method worked just fine. Couple someone please offer some guidance?

    Read the article

  • vmware linux headers not found for ubuntu 10.10 ?

    - by Tumbleweed
    I've installed Vmware 6.5 on Ubuntu 10.10... when I start vmware player/workstation its asking for linux kernel header for some compilation but I'm not able to find the appropriate package, see the Image below.... Update after running following commands sudo -s cd /lib/modules/$(uname -r)/build/include/linux ln -s ../generated/utsrelease.h ln -s ../generated/autoconf.h Error has been changed like below.... ERROR: modinfo: could not find module vmmon ERROR: modinfo: could not find module vmnet ERROR: modinfo: could not find module vmblock ERROR: modinfo: could not find module vmci ERROR: modinfo: could not find module vsock Using 2.6.x kernel build system. make: Entering directory /tmp/vmware-root/modules/vmmon-only' make -C /lib/modules/2.6.35-22-generic/build/include/.. SUBDIRS=$PWD SRCROOT=$PWD/. modules make[1]: Entering directory/usr/src/linux-headers-2.6.35-22-generic' CC [M] /tmp/vmware-root/modules/vmmon-only/linux/driver.o In file included from /tmp/vmware-root/modules/vmmon-only/linux/driver.c:31: /tmp/vmware-root/modules/vmmon-only/./include/compat_wait.h:78: error: conflicting types for ‘poll_initwait’ include/linux/poll.h:72: note: previous declaration of ‘poll_initwait’ was here

    Read the article

  • post-receive hook permission denied "unable to create file" error

    - by ThomasReggi
    Just got gitolite installed on my webserver and am trying to get a post-receive hook that can point the git dir in apache's direction. This is what my post-receive hook looks like. Got this script from the Using Git to manage a web site. #!/bin/sh echo "post-receive example.com triggered" GIT_WORK_TREE=/srv/sites/example.com/public git checkout -f This is the error response i'm getting back from git push origin master from my local workstation. These are files from within my repository. remote: post-receive example.com triggered remote: error: unable to create file .htaccess (Permission denied) remote: error: unable to create file .tm_sync.config (Permission denied) remote: fatal: cannot create directory at 'application': Permission denied Permissions of public. drwxr-xr-x 5 root root 4096 Jun 26 17:23 public

    Read the article

  • Linux with Windows XP vmware guest unable to access certain Internet hosts

    - by unknown
    hi I have annoying problem. My setup is the following: debian Linux, 64 bits, VMWare workstation 7 host, with Windows XP running as guest. From Firefox, or Internet Explorer, I am unable to access few sites, for example nvidia.com, osdir. Basically get connection timed out, on the other hand ping works to those sites. Moreover, Slashdot loads very very slow and sometimes gets horrible text-only version. everything works fine on Linux host I suspect it has something to do with routing on Linux, I recall having similar problem long time ago, which was fixed by setting something in /proc. I tried setting MTU and TCP window size on Windows lower, but did not help Any idea what is going on?

    Read the article

  • Remote Desktop Services Gateway Issue

    - by AVandelay05
    Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

    Read the article

  • Using the same VPC image on multiple workstations

    - by justSteve
    I haven't used an VMs before so brand new to the party. I'm running Win7 off an honest to goodness MSDN license so OS licensing is not an issue. I'd like to think that I could create a VPC image on a USB/eSATA hard drive and move that drive from one Win7-based workstation/laptop to another and I'd have the same services/desktop/computing environment at all of them. I'm a developer working against the IIS7/SQL08 stack with VS10 so i'm working with apps and services as deeply embedded with the OS as you can get. Should I expect to be able to pull this off? thx

    Read the article

  • How to get partition information from non-booting server?

    - by gravyface
    Need to manually rebuild a mirrored array on a server and am in the process of reinstalling SBS 2003 on it. However, it's a Dell server, and know that there's the Dell FAT32 diagnostics partition, a system partition, and a data partition, but do not know the size of each. Planning on reinstalling SBS 2003, all applications on the server, and then doing a System State restore, but figured that not having the correct partitions will cause some grief: am I right? Almost thinking that the size of the partitions shouldn't matter, but not positive. Question: should I care about the size of the partition? If so, how can I get this partition information from a non-booting drive? We have an Acronis image of the one working disk and the partitions are mounted/viewable in Explorer on a workstation, but I'm not sure where the Logical Disk Manager/Disk Management data is stored and/or if there's a way to retrieve it without having a working Windows installation.

    Read the article

  • Remotely connecting to a Hyper-V hosted VM's console.

    - by billpg
    Hi everyone. I've just managed to successfully move an aging beige box into a Hyper-V virtual machine. We used to use the beige box by walking over and sitting at the computer itself, but we can't do that so easily when its inside the Hyper-V system. Is there a way please to access the VM's console from a workstation running XP Pro? Please note that its an obscure OS running inside the VM, so installing a VNC or similar service inside the VM is not an option. Many thanks.

    Read the article

  • SQL Server 2000 + ASP.NET: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'

    - by Rick
    I just migrated a development workstation FROM: Windows XP Pro SP3 with IIS 6 TO: Vista Enterprise 64bit with IIS 7 Since the move, one of my pages that accesses an SQL Server 2000 database is receiving the following error from my ASP.NET 2.0 web page: "Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'." I have: enabled Windows Authentication in IIS and web.config disabled Anonymous Authentication in IIS set up Impersonation to run as the authenticated user verified that the logged in user (in this case, me) has access to the appropriate database on the SQL Server verified that my login and impersonation information is correct in the ASP.NET page by checking User.Identity.Name and System.Security.Principal.WindowsIdentity.GetCurrent().Name (both display my username) My connection string using SqlConnection is "Server={SERVER_NAME};Database={DB_NAME};Integrated Security=SSPI;Trusted_Connection=True;" Why is it trying to login with NT AUTHORITY\ANONYMOUS LOGIN? I have to assume it's some setting or web.config entry specific to IIS7 since it worked fine before the migration. NOTE: The SQL Server is Windows authentication only - no mixed mode or SQL only.

    Read the article

  • Group policy results failing with "Invalid class" error

    - by bshacklett
    When trying to run the Group Policy Results Wizard against a specific workstation, I'm getting the following error: The wizard was unable to generate the computer or user's data due to insufficient permissions. Details: Invalid class I'm guessing that the class being referred to is a WMI class, but I haven't gotten much farther. I've run sfc /scannow on the machine with no luck. I've also followed all of the recommendations in this article: http://windowsxp.mvps.org/repairwmi.htm. I cannot find anything useful in the event logs and I can't think of anywhere else I could look to find out what's really happening here. Any help would be appreciated.

    Read the article

  • 3 Monitors 2 different graphic cards

    - by Michael
    I am looking to add a third monitor to my workstation. I currently have 2 monitors connected to a geforce gt 120. I am wanting to find the cheapest solution on adding another monitor, I have a old ati x300 laying around and wanting to know if I would be able to use that to power the other monitor and if it would conflict with my other graphic card (I am not a gamer). What I want to do is have the at x300 power 1 monitor via dvi and the gt 120 power 2 monitors via vga and dvi. Thanks edit: im running windows 7 64bit

    Read the article

  • PDAnet on Android IP on PC is not public IP. Where does the NAT take place, PDAnet or Verizon?

    - by lcbrevard
    When using PDAnet on a PC (Win7 ultimate) to USB tether a Motorola Droid on Verizon 3G the IP address of the PC appears to be public - 64.245.171.115 (64-245-171-115.pools.spcsdns.net) - but connections show as coming from another public IP - 97.14.69.212 (212-sub-97.14.69.myvzw.com). Someone is performing Network Address Translation - either PDAnet or within the Verizon 3G network. Can someone tell me who is doing the NAT? Is it PDAnet or is it at Verizon? Is there any possibility of setting up port forwarding, such that connections to the public IP 97.14.69.212 (212-sub-97.14.69.myvzw.com) are forward to the PC? We are testing a network protocol that requires either a true public IP or forwarding a range of ports from the public Internet to the system on which the software runs (actually Linux hosted by VMware Player or Workstation on a PC running Windows).

    Read the article

  • File creation time on Windows vs Linux

    - by Sergei
    We have following setup: mountserver - debian linux fileserver1 - Windows 2008 R2 Storage server fileserver2 - Celerra NS20 exporting CIFS share workstation - windows 7 with mapped drive to share on fileserver2 What we are doing: mounted share from fileserver1 on mountserver, e.g. /shared/fileserver1 mounted share from fileserver2 on mountserver, e.g. /shared/fileserver2 ran rsync on mountserver to sync data from fileserver1 to fileserver2.Used atime as parameter to sync data not older than X after a while tried to delete data older that Y on /shared/fileserver2. From what I see, linux stat command on mountserver returns following when quering file on /shared/fileserver2: At the same time when I open property for the same file using mapped drive connected to fileserver2,I see following for the same file: As you can see, Created date of 12 August shown in Windows Explorer is nowhere to be seen using stat command Am I missing something here?

    Read the article

  • How do I add color syntax highlighting to GNU emacs?

    - by Alex Reynolds
    I have two versions of emacs available to me on a locked workstation: $ /usr/local/bin/emacs --version GNU Emacs 22.3.1 $ /usr/bin/emacs --version GNU Emacs 21.4.1 In both cases, my terminal type is xterm when I run either version of emacs. When I run the v21 version of emacs, I get syntax coloring for Perl, HTML, and other modes. When I run the v22 version, I do not get syntax coloring. I would like to migrate from the v21 version because the combination of v21 emacs, GNOME Terminal and GNU Screen is eating Ctrl-arrow key chords, which prevents me from moving quickly between words. (OS X Terminal and GNU Screen do not have this issue.) The v22 version allows use of Ctrl-arrow key combinations with GNOME Terminal and GNU Screen. How do I fix the v22 version (or ask my sys admin to fix) so that it once again highlights syntax and allows me to use Ctrl-arrow key combinations?

    Read the article

  • How Can I assign an IP address to my virtual Windows Server, so that I can start using it almost as a VPS?

    - by Nelson Symonds
    We are a small office set up with two PC's out of which one of my PCs runs 24hrs. Its almost equivalent to a small server, but right now we're in need of a server which is why I am planning to keep my machine as well as a server into a single PC. I've used VMware Workstation to create a powerful Windows Server 2008 within my PC and I want to attach it to my Network Switch through the same PC where I am hosting it. I want to use it almost like a physical server with an IP address and everything so that I can connect from one Pc to the Server directly or my applications can connect to Server straight with the IP address. How should I do this? Step by step instructions would be appreciated. Thanks in Advance, Best regards Nelson

    Read the article

  • Redhat 6 gui installation VS kickstart gives me different packages?

    - by jonaz
    If i do the graphical install and select basic server + aide and screen i get a system with 535 installed packages. If i look at the /root/anaconda-ks.cfg file in that freshly installed system i see: %packages @base @console-internet @core @debugging @directory-client @hardware-monitoring @java-platform @large-systems @network-file-system-client @performance @perl-runtime @security-tools @server-platform @server-policy @system-admin-tools pax python-dmidecode oddjob sgpio certmonger pam_krb5 krb5-workstation nscd pam_ldap nss-pam-ldapd perl-DBD-SQLite aide screen If i then install a NEW system using a kickstart only containing those packages i get 620 installed packages. So basicly my question is why does the system install almost 100 more packages when using kickstart compared to the GUI installation when the exact same packagegroups are selected?

    Read the article

  • Computer freezes for 2+ seconds, mouse still moves

    - by xsaero00
    I have this problem on my workstation. The computer would effectively freeze for 2-5 seconds for no apparent reason, then continue as normal. While frozen the mouse would still be movable, but only on one of screens in my multi-screen setup. What can be the likely cause. System: CPU: i7-920 Memory: 12G of Patriot DDR3, 6 modules OS: SLED 11, Suse Linux Enterprise Desktop, using Gnome Main board: Asus P6T Video: two Nvidia 9500GT connected to three displays I am using memory at recommended settings of 8-8-8-1333. It has an XMP profile. Th CPU is a bit overclocked to 3.3 GHz, but my cooling more than allows for it. I ran the computer with all overclocks off and lower memory speed but the issue was still there. Any ideas? Where should I start looking?

    Read the article

  • Only 192.168.0.3 can request most files, but anyone can request /public/file.html

    - by mattalexx
    I have the following virtual host on my development server: <VirtualHost *:80> ServerName example.com DocumentRoot /srv/web/example.com/pub <Directory /srv/web/example.com/pub> Order Deny,Allow Deny from all Allow from 192.168.0.3 </Directory> </VirtualHost> The Allow from 192.168.0.3 part is to only allow requests from my workstation machine. I want to tweak this to allow anyone to request a certain URL: http://example.com/public/file.html How do I change this to allow /public/file.html requests to get through from anyone? Note: /public/file.html doesn't actually exist as a file on the server. I redirect all incoming requests through a single index file using mod_rewrite.

    Read the article

  • Choosing A Power Supply [closed]

    - by Geeks On Hugs
    Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

    Read the article

  • Security Audit Failures in Event Viewer Windows Server 2008R2

    - by Jacob
    When I am looking at the security tab of my event viewer on a Windows Server 2008 R2, I am showing a ton of Audit Failures with Event ID 4776. The computer attempted to validate the credentials for an account. Authentication Package: MICROSOFT_AUTHENTICATION_PACKAGE_V1_0 Logon Account: randy Source Workstation: HPDB1 Error Code: 0xc0000064 I verified the account "randy" exist in my Active Directory. From my understanding, there has not been any recent password changes. Is there any way to get detailed information on this error? I am wondering what program is requesting this information. Also, is there any way to clear this error up? I was thinking about resetting the password and changing it back to the original.

    Read the article

  • "RPC Server is unavailable" on Windows 7 Client with Samba3 making logon impossible

    - by HalloDu
    I am running an Samba 3.4.* Server with LDAP Backend on Ubuntu 10.04 LTS as a PDC for purely Windows 7 Clients (about 50). It worked quite fine for a long time, but now sometimes on some machines (really strange to replicate) I cannot login, because he tells me that there are no logon servers. When I look in the machines eventlog after logging in locally, the only error it shows is: "RPC Server is unavailable". The system was ported quite a while back from another machine running the same software versions to this new one. Are there maybe trust or caching issues between the workstations and the domain controller? The number of machines affecting is steadily increasing and so do you know any reason as to why this problem occurs? Any information on workstation and domain trust would also be welcome (After googleing I did not find anything really enlightening).

    Read the article

< Previous Page | 26 27 28 29 30 31 32 33 34 35 36 37  | Next Page >