Search Results

Search found 14356 results on 575 pages for 'personal info'.

Page 300/575 | < Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >

• Wireless card not found on Ubuntu

  - by Idealflip

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• How to install compiler and binutils on FreeNAS?

  - by spoulson

  I'd like to run a backup tool, duplicity, that apparently requires a cc compiler and binutils. I'm able to locate and install the required BSD packages for python, gcc, and dependencies from ftp2.freebsd.org. However, I can't find binutils. How are binutils installed on a system like FreeNAS? I'm working with FreeNAS 0.70 (based on FreeBSD 7.2). I see several packages with binutils in the name, but it's not clear any of them are for my i386 platform. e.g. I see i386-rtems-binutils-2.19.1, but I can't find any info that suggests this is correct for my platform. Google results mention it's for realtime systems.

  Read the article

• Roundcube can't connect to PostgreSQL database

  - by kenny.r

  I'm trying to install Roundcube on a CentOS 5.5 server, with a PostgreSQL 8.1.22 database. The first page of the installer script, that checks for the presence of php libraries and such, gives me green OKs across the board. I even went out of my way to install the optional ones. Page two generates me two configuration files (main.inc.php and db.inc.php) which I put into place. Page three is where things go wrong: Check DB config DSN (write): NOT OK(MDB2 Error: connect failed) Make sure that the configured database exists and that the user has write privileges DSN: pgsql://roundcube:password@localhost/roundcubemail The info you see there (user roundcube, password password, server localhost and database roundcubemail) is all correct. The database roundcubemail belongs to the user roundcube and it has write permissions. I have no clue why it can't connect to that database. I'm managing it with phpPgAdmin, which is running on the very same Apache, on the same server!

  Read the article

• Apache: domains working fine, subdomains not working anymore

  - by David Lawson

  Hi there, I'm not sure when, but suddenly subdomains aren't working on my server. e.g. www.davidlawson.co works, but david.lawson.co isn't working. <VirtualHost 173.203.109.191:80> ServerAdmin [email protected] ServerName david.lawson.co ServerAlias davidlawson.co ServerAlias www.davidlawson.co DocumentRoot /var/www/lawson/david <Directory /var/www/lawson/david/> Options -Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog /var/log/apache2/lawson/david/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/lawson/david/access.log combined </VirtualHost> Any suggestions on how to debug this further, or what the problem might be?

  Read the article

• zip being too nice (osX)

  - by stib

  I use zip to do a regular backup of a local directory onto a remote machine. They don't believe in things like rsync here, so it's the best I can do (?). Here's the script I use echo $(date)>>~/backuplog.txt; if [[ -e /Volumes/backup/ ]]; then cd /Volumes/Non-RAID_Storage/; for file in projects/*; do nice -n 10 zip -vru9 /Volumes/backup/nonRaidStorage.backup.zip "$file" 2>&1 | grep -v "zip info: local extra (21 bytes)">>~/backuplog.txt; done; else echo "backup volume not mounted">>~/backuplog.txt; fi this all works fine, except that zip never uses much CPU, so it seems to be taking longer than it should. It never seems to get above 5%. I tried making it nice -20 but that didn't make any difference. Is it just the network or disc speeds bottlenecking the process or am I doing something wrong?

  Read the article

• How to create a chained differencing disk of another differencing disk in Virtual Box?

  - by WooYek

  How to create a differencing disk (a chained one) from a disk that is already a differencing image? I would like to have: W2008 (base immutable) - W2008+SQL2008 (differencing, with SQL installed) --- This I can do. - W2008+SQL2008+SharePoint (chained differencing with Sharepoint installed on top of SQL2008) There's some info about it the manual: http://www.virtualbox.org/manual/ch05.html#diffimages Differencing images can be chained. If another differencing image is created for a virtual disk that already has a differencing image, then it becomes a "grandchild" of the original parent. The first differencing image then becomes read-only as well, and write operations only go to the second-level differencing image. When reading from the virtual disk, VirtualBox needs to look into the second differencing image first, then into the first if the sector was not found, and then into the original image.* I don't get it...

  Read the article

• Problems installing Linux to IDE connected compact flash card

  - by mathematician1975

  I have been trying to install Ubuntu on some hardware (Netcom NC-499 board that contains a Vortex86DX processor). I am trying to install to a compact flash card attached to the board via an IDE adaptor, the aim being that the board will boot up and simply treat the compact flash like a normal hard drive. The processor vendor claims support for Ubuntu 10.04 but I am having problems installing it onto the card. I have been trying using a USB CD-ROM drive and the standard .iso image from the ubuntu site (md5 checksum works out fine so no problem there) but I have had no success at all. I have been able to do this with Ubuntu 8.04 but with no other version (9.04 and 10.04 desktop and alternative discs all fail). My question is what other options are available to me to try and install this? I have googled myself apart trying to find out but other than a few sites describing USB based installs using flash memory sticks for very specific hardware, I have found no useful info at all. Any suggestions will be gratefully received.

  Read the article

• iTunes Title Bar is Equal to the Location of the Library file?

  - by Urda

  I have never been able to get a clear answer on why the latest edition of iTunes does this. I have my entire iTunes library located in C:\itunes\ and the library data files inside C:\itunes\!library_info for backup purposes. However when version 9 of iTunes came out it went from having iTunes as the title, to !library_info. Anyway to get around this without moving my data files away? Annoying "feature" if that is what it is. Again Apple support and forums were of no help to me. Anyone have insight on this? System Info: Windows Vista x86 Ultimate, latest updates. iTunes Version 9.0.3.15 Screenshot: http://farm5.static.flickr.com/4072/4414557544_d0b25eb64c_o.jpg Flickr Page: http://www.flickr.com/photos/urda/4414557544/

  Read the article

• Anyone else being hit by traffic on TCP port 11370

  - by Jakub

  I've been watching my logs (Ubuntu 9.10 server) and dunno about any of you but I am getting a ton of traffic from sources like Russia, Romania, etc.. on port 11370 (my iptables are logndrop'ing it. But was just curious). Some googling revealed this info: http://www.keysigning.org/sks/ -which seems to use port 11370 & 11371 Could that be the service they are scanning for (i don't run it)? ICS shows this: https://isc.incidents.org/port.html?port=11370 Just curious what you guys think and if anyone has seen this before? If need be I can post my log on here, but its just a dropped log of TCP port 11370 from various IPs. Thought it was strange as thats the ONLY Port I seem to repeatedly be hit on (from logs). I'm running on a Linode (VPS) if that matters to annyone.

  Read the article

• Calculate data transferred in a local LAN

  - by ramdaz

  How do you calculate the data flown between a computer and the gateway computer. I have a Linux router/gateway running IP Tables which routes internet traffic in a LAN. I have individual users with IP/MAC Address mapped who access Interet through the gateway computer. I would like to find out the traffic utilized by individual users. Is it possible for us to find out what kind of traffic was HTTP, SMTP, FTP etc. Is it also possible to pool the information on hourly basis, and get specific info so that I can store information in a database? I have heard of IP Accounting? Is that the right way

  Read the article

• Extract data from specific range of cells in multiple worksheet in multiple files.

  - by Michele

  Extract data from specific range of cells(always the same cells) in multiple worksheet in multiple files. 1 file=1 day. I have 6 technicians each day of the week, Monday thru Friday. So, 5 files with 6 worksheets. I have entered specific info in specific cells of every work sheet. The range is constant(the same address in EVERY worksheet in every file.) So, I need a formula to extract and calculate the data in the given range and dump it into another spreadsheet. I can forward an example a file if it will help anyone to answer my question. Or more explanation if necessary is available upon request. JUST PLEASE SOMEBODY HELP ME!!!!! Thank you all in advance. Regards, Michele

  Read the article

• X-Window Modeline for high resolution modes on NEC LCD 22WV monitor

  - by Jakub Narebski

  What should look like X Window System (X.Org) modeline to be put in xorg.conf, for high resolution (incuding recommended 1680x1050 @ 50Hz resolution) for 22" NEC LCD 22WV monitor? X.Org autodetect correctly only 800x600 and lower resolution SVGA modes, unfortunately. How can I generate proper "Modeline" line for xorg.conf? Is information included in NEC_Datasheet_LCD22WV-english.pdf enough (found on NEC LCD 22WV product info page)? What tools there are available to generate proper modeline for a LCD monitor for Linux? MS Windows (MS Windows XP Home) correctly detects and use 1680x1050 resolution; can I somehow get modeline information from MS Windows?

  Read the article

• Cannot boot from windows 7 DVD

  - by webnoob

  Hi All, I have just purchased windows 7 64bit. I entered the disk in the drive and it told me I couldn't upgrade as I am using XP so I have tried to boot from CD instead but it doesn't work. It seems to look at the disk for a few seconds and then ends up at a screen saying windows failed to start and then I hit enter and it loads windows XP again. Does anyone know what could cause this? Here is my system info: Time of this report: 4/15/2010, 18:11:39 Machine name: MYCOMP Operating System: Windows XP Professional (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr.100216-1514) Language: English (Regional Setting: English) System Manufacturer: Dell Inc. System Model: OptiPlex 755 BIOS: Phoenix ROM BIOS PLUS Version 1.10 A09 Processor: Intel(R) Core(TM)2 Duo CPU E6550 @ 2.33GHz (2 CPUs) Memory: 3316MB RAM Page File: 568MB used, 4631MB available Windows Dir: C:\WINDOWS DirectX Version: DirectX 9.0c (4.09.0000.0904) DX Setup Parameters: Not found DxDiag Version: 5.03.2600.5512 32bit Unicode

  Read the article

• Cannot boot from windows 7 DVD

  - by webnoob

  Hi All, I have just purchased windows 7 64bit. I entered the disk in the drive and it told me I couldn't upgrade as I am using XP so I have tried to boot from CD instead but it doesn't work. It seems to look at the disk for a few seconds and then ends up at a screen saying windows failed to start and then I hit enter and it loads windows XP again. Does anyone know what could cause this? Here is my system info: Time of this report: 4/15/2010, 18:11:39 Machine name: MYCOMP Operating System: Windows XP Professional (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr.100216-1514) Language: English (Regional Setting: English) System Manufacturer: Dell Inc. System Model: OptiPlex 755 BIOS: Phoenix ROM BIOS PLUS Version 1.10 A09 Processor: Intel(R) Core(TM)2 Duo CPU E6550 @ 2.33GHz (2 CPUs) Memory: 3316MB RAM Page File: 568MB used, 4631MB available Windows Dir: C:\WINDOWS DirectX Version: DirectX 9.0c (4.09.0000.0904) DX Setup Parameters: Not found DxDiag Version: 5.03.2600.5512 32bit Unicode

  Read the article

• Mac OS X bash: uninstall all apache and PHP occurences

  - by fireeyedboy

  Hi all, How do I find all installed apache and PHP occurences on a Mac OS X system in bash and uninstall them? My motivation: I've managed to install multiple apache and PHP packages (I believe it's called packages in Unix terms, correct?) at some point, and I'ld like to start out fresh again, without completely re-installing Mac OS X again. Also, I'ld like to install suPHP along with apache this time, and I believe I need to compile apache with some additional stuff for that. But that is a challenge I'll deal with later, and probably ask a question about then. :) Thank you in advance for your info.

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Arch Linux Terminal (via ssh) + Dropbox but sync only 1 single selected folder

  - by Norfeldt

  Sorry for the weird title... I'm (still) quite new to linux and are doing shh commands to an Arch Linux device that has not screen output options. So everything has to be done in the terminal (not my super element). I use the linux device to play around with python (which is quite fun). Now I would like sync my script folder with dropbox. Since I don't have enought space to sync all my dropbox files to the device, I would like to know how I can set it up in a way that it only syncs with the folder I choose. At the time being I have not installed dropbox because I'm afraid that it will immediately begin to sync all my dropbox folders onto my linux device. BONUS INFO: I already have created a folder in my dropbox that I that contains some py scripts I would like to have synced with my linux device.

  Read the article

• linux need to discover local sata mirror before hba attached scsi

  - by Ryan

  (none of the machines mentioned are in production) Hello, I'm trying to install Centos 5.4, which wants to put the boot loader on either the boot sector of the boot drive (a local SATA mirror, recognized second as sdb) or the mba of a hba-attached SCSI array (recognized first as sda). There's a LILO install already on the mba of sdb, which keeps trying to boot first. If I zero out the MBA of sdb, would the boot loader at sdb1 be found and booted? I was thinking of that as a plan B, as I was mostly thinking of coaxing CentOS to find the local mirror first and bring that up as sda, but I haven't found info on how to do this anywhere.

  Read the article

• Proffesional video editor that can handle FLV?

  - by acidzombie24

  I tried Adobe Premiere Pro CS3 and was not able to open my file (unsupported format). Media player can open it thanks to ffdshow (tryouts IIRC). Premiere doesnt seem to want to use ffdshow. I tried renaming it to AVI and hoped Premiere would open it via ffdshow but it didnt and i checked and disabled the dont use ffdshow option in ffdshow video decoder option. What is a good proffesional video editor that can handle FLV? All ffmpeg based editors died on it and virtualdub got close but had a bad framerate. Probably bc it didnt know it was a streaming vid and the start is 26mins of 31min video. More info here but what can i use to open and properly convert flv video http://superuser.com/questions/50779/windows-media-based-video-audio-converter

  Read the article

• Can someone recommend a Compact Flash card to be used as a boot disk/fixed disk.

  - by Hamish Downer

  I have an early Acer Aspire One netbook, and the flash drive is really slow at writing. I've taken it apart to add more RAM, but I've pretty much stopped using it. I've read about people replacing the SSD with a Compact Flash card and a CF to ZIF adapter but I've also read about some Compact Flash cards where the manufacturer has permanently disabled the boot flag to stop people doing this kind of mod. (Can't find the link any more though). (Although I have just found some info about CF cards that says "Most CompactFlash cards by default identify themselves as removable media instead of fixed disk" and that this is an issue for Windows. So my most specific question is: can someone recommend a compact flash card that does allow the boot flag to be set and to be set as Fixed Disk? Please say whether you've done it yourself, or just heard about it from someone else. Beyond that, is this generally a problem?

  Read the article

• Granting rights to the sa account using osql

  - by Jan Jongboom

  I'm installing sql instances through script, and after creating a certain instance, I cannot get the sa account to be enabled through osql. What I've tried osql -S .\INSTANCENAME -E use master ALTER LOGIN sa ENABLE GO Using SSMS to enable the account (by logging in using Windows Auth., 'New query', and exactly the same query as in 1.) Suggestions in this issue No. 2. is actually working; and the account is enabled instantly. No 1 is not working, not even with the suggestions provided in 3., I have restarted the SQL services after executing the commands in osql. Additional info Windows 2003 Server, Microsoft SQL Server 2005 Enterprise, No password policies apply to the account.

  Read the article

• Apache 2 Symbolic link not allowed or link target not accessible

  - by djechelon

  While the title of this question matches an already asked question, in my case I already set Options +FollowSymLinks. The setup is the following: my hosting setup includes htdocs/ directory that is the default document root for HTTP websites and htdocs-secure that is for HTTPS. They are meant for sites that need a different HTTPS version. In case both share the same files I create a link from htdocs-secure to htdocs by ln -s htdocs htdocs-secure but here comes the problem! Log still says Symbolic link not allowed or link target not accessible: /path/to/htdocs-secure Vhost fragment Header always set Strict-Transport-Security "max-age=500" DocumentRoot /path/to/htdocs-secure <Directory "/path/to/htdocs-secure"> allow from all Options +FollowSymLinks </Directory> I think it's a correct setup. The HTTP version of the site is accessible, so it doesn't look like a permission problem. How to fix this? [Add] other info: I use MPM-itk and I set AssignUserId to the owner/group of both the directories

  Read the article

• haproxy not passing X_FORWARD_FOR on HTTP POST

  - by Mark L

  Hello, I've setup HAProxy with the option forwardfor option so it'll pass on the user's IP to PHP via $_SERVER[ "HTTP_X_FORWARDED_FOR" ]. If the page request isn't a POST it's populated fine but if it is then it won't be populated. Any ideas where I've gone wrong? Thanks everyone! My whole HAProxy conf file for reference: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 4096 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen webfarm :80 mode http balance roundrobin option forwardfor server webA 192.168.240.4 weight 1 maxconn 2048 check server webB 192.168.240.3 weight 1 maxconn 2048 check listen smtp :25 mode tcp option tcplog balance roundrobin server smtp 192.168.240.4:25 check

  Read the article

• What could cause my LAN Pings be greater than 100ms?

  - by James Holland

  I have 2 servers (Both: Windows Server 2008, Dual Xeon 2.8Ghz, 32GB RAM, 8 x 15k SAS Drives). One of them is a DC / Web server / Exchange Server, the other is a SQL Server (2008). I have a 48 port Netgear GS748T Gigabit switch. When I ping from server to server, I get ping times <1ms, great, but when I ping from a PC, I get varying pings from the occasional <1ms to 500ms!! If I log into either server and look at Task Manager, CPU usage peaks at 20%, memory usage is 100%, but I am led to believe this is normal as Exchange will just use as much as you have, and release it when requested. Network usage peaks at 1%. I really don't understand how the ping can vary that much. I know I am giving very little info, but this is all I know, I apologise, but can anyone help? In response to question, I have pinged by both IP address and hostname, no difference in ping times.

  Read the article

• foswiki: use genPDF extension with topic templates?

  - by Mica

  I have a foswiki installation for keeping ISO and other documents. I would like to create a PDF from each page. How can I create a topic template with different headers and footers for each topic template? More info: When a user creates a new topic, they can choose a template. I've made several templates for Functional and Programming specs. The functional spec and programming spec require different document numbers. I would like for the software engineers to be able to create a new topic, choose the template, then be able to generate a PDF from the wiki page, pulling the appropriate document number, and some other text into the headers and footers. I am not very familiar, and haven't been able to find any examples on doing this. Any help would be appreciated!

  Read the article

< Previous Page | 296 297 298 299 300 301 302 303 304 305 306 307  | Next Page >