Search Results

Search found 9494 results on 380 pages for 'online inventory'.

Page 302/380 | < Previous Page | 298 299 300 301 302 303 304 305 306 307 308 309  | Next Page >

• wrt54gl reboots; troubleshooting steps?

  - by Bill

  I am using about 10 wrt54gl's in a small school. I am using a combination of stock firmware and Tomato 1.25, slowly moving towards all Tomato. We have had these devices installed for several years without problems. Recently, more and more of the units have started to spontaneously reboot, usually during high-traffic times (but not always). For the most part, the rebooting is not critical for us, but the wrt54gl's temporarily revert to 192.168.1.1 on the LAN ethernet ports and conflict with a critical server that's already installed with that IP. (Yes -- we plan to move the server off that address, but it is an involved process.) Both Tomato and the stock firmware (several versions from recent to several years old) exhibit the same problem: random reboots and reverting to 192.168.1.1 and conflicting temporarily with our server until the firmware boot process finishes. Here are my questions: Any way to prevent the wrt54gl's from reverting to 192.168.1.1 during the boot process? I was thinking of doing a custom firmware mod, although I hate to go that direction. Any steps to take in troubleshooting the reboots? Only some of the wrt54gl's reboot, which is odd. Others stay online for weeks and months without issues. Thanks.

  Read the article

• Member Status: Inquorate in RHEL 5.6

  - by Eugene S

  I've encountered a strange issue. I had to change the time on my Linux RHEL cluster system. I've done it using the following command from the root user: date +%T -s "10:13:13" After doing this, some message appeared relating to <emerg> #1: Quorum Dissolved (however I didn't capture the message completely). In order to investigate the issue I looked at /var/log/messages and I've discovered these errors. Below is the output of few commands I got when tried to investigate the issue, however I don't have enough knowledge to make use of this information. [root@system1a ~]# clustat Cluster Status for system4081 @ Sun Mar 25 11:45:48 2012 Member Status: Inquorate Member Name ID Status ------ ---- ---- ------ chb_sys1a 1 Online, Local chb_sys2a 2 Offline [root@system1a ~]# cman_tool nodes Node Sts Inc Joined Name 1 M 872 2012-03-25 08:43:07 chb_sys1a 2 X 0 chb_sys2a [root@system1a ~]# qdiskd -f -d [17654] debug: Loading configuration information [17654] debug: 0 heuristics loaded [17654] debug: Quorum Daemon: 0 heuristics, 1 interval, 10 tko, 0 votes [17654] debug: Run Flags: 00000035 [17654] info: Quorum Daemon Initializing stat: Bad address [17654] crit: Initialization failed I tried to search through the internet and found out a quite similar issue here. However, for some reason I am not able to access the bug on bugzilla. The link to the bug is here

  Read the article

• Real-time local backup with versioning on Windows 7/8

  - by Borda

  I'm looking for a reliable backup solution on Windows, something with a feature set similar to Yadis. I've been using CrashPlan for 2 months, but their software lost more than 1TB of my data, that's why I'm looking for alternatives. Requirements: Real-time folder-to-folder backup: I don't need online features, I want to use this to duplicate my files between my local disks. Versioning support: Should be able to choose how many versions to keep of the files. Plain backup: I'd like to be able to open the backup without special software. No proprietary file format. External disk support: Shouldn't have any problem using external disks, at least on the source side. Backup every file, even locked/system files. (Yadis fails this one) Should start automatically, and have a comfortable GUI. Should use actively maintained and/or popular software. I don't want to use discontinued products. Optional requirements: Low RAM usage I'm not really comfortable with something that eats 1GB of my RAM. Compression support Preferably ZIP, but I'm not picky about this. Any ordinary everyday format is acceptable. Freeware or Open Source Preferred, but not necessary. I can do a one-time payment within reasonable bounds. (preferably under $100) I only need Windows support, but if it works on Linux, that's a plus. I've already searched and tried lots of software, most of them failed at the plain backup, the versioning or the locked file backup requirements.

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• How to compare old CPU to new CPU?

  - by Lasse V. Karlsen

  I hope this question doesn't get closed at once :) I have an old laptop, a Compaq NC4200, which is going its final laps around the track these days. Battery is dead, and everything kinda runs slow. It also has only 1GB of memory, and even though I don't know if it can take more, I probably wouldn't be able to get hold of any that matches without having to special order it. The size, however, has been ideal for my usage pattern, so I'm looking to replace it with a similarly sized laptop, at least in the same size category. However, it's been a while since I tried keeping track of CPUs, so I have a question. The old laptop has a Intel Pentium M 760 1.86GHz processor. One laptop I found online has a Intel Pentium SU4100 1.3GHz dual-core. This type of processor seems to be quite common in the price and size-range I've been looking. What kind of relative performance boost could I expect from the old one to the new one? I am not expecting a "about 7.45x speed", but some indication would be nice. For instance, dual-core tells me it might be akin to 2.6GHz, but I assume I can't simply compare 1.86GHz to 2.6GHz and expect the new one to run about 1.4x as fast, I expect more these days. Or is that unrealistic for this kind of processor? Do I need to up my price range and go for a 2+ GHz processor?

  Read the article

• weird POST request in IIS logs

  - by MIrrorMirror

  I noticed weird log entries (unless there's something i don't understand) in my IIS (7.5) logs. it's an online dictionary with requests ( user friendly url rewriting ) and most of them are GET. However I noticed weird POST requests which are taking place by a person who is trying to crawl our content ( tens of thousands of such requests ) 2013-11-09 20:39:27 GET /dict/mylang/word1 - y.y.y.y Mozilla/5.0+(compatible;+Googlebot/2.1;++http://www.google.com/bot.html) - 200 296 2013-11-09 20:39:29 GET /dict/mylang/word2 - z.z.z.z Mozilla/5.0+(iPhone;+CPU+iPhone+OS+6_0+like+Mac+OS+X)+AppleWebKit/536.26+(KHTML,+like+Gecko)+Version/6.0+Mobile/10A5376e+Safari/8536.25+(compatible;+Googlebot-Mobile/2.1;++http://www.google.com/bot.html) - 200 468 2013-11-09 20:39:29 POST /dict/mylang/word3 - x.x.x.x - - 200 2593 The two first requests are legal. Now for the third request, I don't think I have allowed cross domain POST. if that what the third log line means. all those POST requests take that much time for unknown reasons to me. I would like to know how are those POST requests possible and how can I stop them. p.s. I have masked the IPs on purpose. any help would be appreciated! thank you in advance.

  Read the article

• "cannot receive new filesystem stream: invalid backup stream" error when unpacking flash archive on solaris 10

  - by Bovril

  I've searched around but i'm having no luck with some peculiar behavior with a flash archive. I'm using HP Server Automation 9.14 to deploy the OS. I'm creating a Solaris 10 flash archive to create a snapshot default build in our environment. I create the flash archive with # flar create -c -S -n g8-solaris10-u10 g8-solaris10-u10.flar It seems to create the file without any problems (exit status 0). When deploying to a new system (same hardware), it extracts to a point and then bails. The last error in the log I can see is Extracted 2047.00 MB ( 82% of 2488.98 MB archive) ERROR: Could not read file (172.27.118.100:/media/opsware/sunos/flar/g8-solaris10-u10.flar ERROR: Errors occurred during the extraction of flash archive. The file /tmp/flash_errors contains the list of errors encountered ERROR: Could not extract Flash archive ERROR: Flash installation failed The error log contained the following message cannot receive new filesystem stream: invalid backup stream A previous version of this flash archive (1.8gb) worked ok, so I suspect size may be a factor. The source system (the one the flash archive is an image of) is an HP BL460C GEN8 some more info below. OS version Info # uname -a SunOS testhostname 5.10 Generic_147441-01 i86pc i386 i86pc # who -r . run-level 3 Oct 15 08:15 3 0 S disks # echo | format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0t0d0 <DEFAULT cyl 17841 alt 2 hd 255 sec 63> /pci@0,0/pci8086,3c06@2,2/pci103c,3355@0/sd@0,0 Specify disk (enter its number): Specify disk (enter its number): zpools # zpool list NAME SIZE ALLOC FREE CAP HEALTH ALTROOT rpool 136G 24.6G 111G 18% ONLINE - Zones # zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / native shared The file size of 2047 seems suspiciously close to 2048, which is concerning. Any help would be greatly appreciated. Thanks

  Read the article

• Is there a way to extract a "private certificate key" from Chrome and import it into Firefox ?

  - by user58871

  This is a classical Catch-22 situation. I was using online banking the other day under Chrome. I had to order a digital certificate so that I could extend my privileges. The stupid thing is that when I got approved and opened the certificate installation menu, I saw only versions for IE/Firefox available. What the heck, I said, and chose FF - the result I got was Error 202 - ERR:CERT:INVALID. I opened FF, got to the same page, and tried to install the damn thing from there, but got a message basically saying that I must have been given a private key which obviously FF doesn't find. I read a bit, and it turned out that I really must have been given such a key but only to the browser that I ordered the cert with, i.e. Chrome. The worst thing is that if I deactivate my order, and reissue a new cert, this time from FF, I MUST go to a bank office (!!!WTF), but I am currently studying abroad, so I can't just go back. Is there a way, that I could extract that key from Chrome's profile, and import it into FF under Windows ? I will be glad to know

  Read the article

• Why is squid breaking kerberos/NTLM auth?

  - by DonEstefan

  I'm using squid 2.6.22 (Centos 5 Default) as a proxy. Squid seems to break the authentication process for web pages when they require NTLM or Kerberos Auth. I tested with sharepoint 2007 and tried all 3 authentication methods (NTLM, Kerberos, Basic). Accessing the site without squid works in all cases. When I access the same page with squid, then only basic-auth works. Using IE or Firefox desn't make any difference. Squid itself can be used by anybody (no auth_param configured). Its a bit tricky to find solutions online, since most of the topics whirl around auth_param for authenticating users to squid rather than authenticating users to a webpage behind squid. Could anyone help? Edit: Sorry, but my first test was totally screwed up. I tested against the wrong webservers (Memo to myself: always check assumptions before testing). Now I realized that the problem scenario is completely different. Kerberos work for IE Kerberos works for Firefox (after changing "network.negotiate-auth.trusted-uris" in about:config) NTLM works for IE NTLM does NOT work in Firefox (even after changing "network.automatic-ntlm-auth.trusted-uris" in about:config) By the way: The feature that provides NTLM-passthrough in squid is called "connection pinning" and the HTTP header "Proxy-support: Session-based-authentication""

  Read the article

• Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

  - by Elliot.Bradshaw

  I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

  Read the article

• File sharing for small, distributed, non-technical, non-profit organization?

  - by mnmldave

  Problem: I've started volunteering for a small non-profit with fewer than five non-technical Windows users who need to share 20-30GB of files (Office documents, images, PDFs, etc.) amongst themselves online. Background: The users are accustomed to a Windows network share on a machine that backed up their data locally. An on-site "disaster" has forced them to work from their homes for awhile and to re-evaluate their file sharing needs (office was located in an old building with obvious electrical issues, etc.). Access to time from volunteers with IT experience seems to be difficult. Demonstrably minimizing energy consumption is a nice-to-have. I'm currently considering Jungle Disk (a Desktop account shared amongst the handful of employees since their TOS and my inquiries to their helpdesk seem to indicate this is permissible). It appears easy-to-use, inexpensive, secure, has backup functionality, and can scale to accomodate more data when needed. I've not used it myself though (have only used Dropbox for personal use) and systems isn't my area of expertise, so am worried I might be jumping on a bandwagon. That said, any suggestions, thoughts or similar experiences would be really appreciated.

  Read the article

• EC2 Configuration

  - by user123683

  I am trying to create a server structure for my EC2 account. The design I have chosen consists of 2 instances running in different availability zones, elastic load balancer, an auto-scaling group with cloudwatch monitoring configured and a security group defining rules for access to the instances. This setup is to support an online web application written in PHP. I am trying to decide what is a better policy: Store MySQL DB on a separate Instance Store MySQL DB on an attached EBS volume (from what i know auto-scaling will not replicate the attached EBS volume but will generate new instances from a chosen AMI - is this view correct?) Regards the AMI I plan to use a basic Amazon linux 64 bit AMI, and install bastille (maybe OSSEC) but I am looking to also use an encrypted file system. Are there any issues using an encrypted file system and communication between the DB and webapp i neeed to be aware of? Are there any comms issues using the encrypted filesystem on the instance housing the webapp I was going to launch a second instance or attach a second volume in the second availability zone to act as a standby for the database - I'm just looking for some suggestions about how to get the two DB's to talk - will this be a big task Regards updates for security is it best to create a recent snapshot and just relaunch and allow Amazon to install updates on launch or is the yum update mechanism a suitable alternative - is it better practice to relaunch instead of updates being installed which force a restart. I plan to create two AMI snapshots one for the app server and one for the DB each with the same security measures in place - is this a reasonable - I just figure it is a better policy than having additional applications that are unnecessary included in a AMI that I intend on using. My plan for backup is to create periodic snapshots of the webapp and DB instances (if I use an additional EBS volume instead of separate instances my understanding is that the EBS volume will persist in S3 storage in the event of an unexpected termination and I can create snapshots of the volume backup purposes). Thanks in advance for suggestions and advice. I am new to EC2 and I may have described unnecessary overkill but I want to try implement what can be considered a best practice solution so all advice is appreciated.

  Read the article

• Unable to activate Windows XP

  - by Josh Kelley

  The latest round of Patch Tuesday updates left my Windows XP computer unbootable. ("Fatal System Error: The Windows Logon Process system process terminated unexpectedly.") After much messing around with the recovery console, an XP CD's repair mode, and manually copying registry files around, I have a system that can boot again. However, I overwrote my OEM XP installation's activation information while trying to run a retail XP CD's setup, so it needs reactivation. Here's my problem: I cannot activate it at all. I log in, Windows tells me I have to activate to continue, I click Yes, and absolutely nothing happens: no windows, no response to keyboard or mouse, no response to Ctrl-Alt-Del, nothing. Safe mode works, but I can't activate in safe mode (EDIT: not even safe mode with networking). I read a trick online of pressing [Windows Key]+U to bring up the Microsoft Narrator, and that works, but clicking its Microsoft Web Site link does nothing. My last attempt to resolve this was to reinstall Windows off of the OEM CD. Now I have two parallel Windows installations, both on the same hard drive, one with all of my stuff and no way to activate it, one fully activated with no usable programs. Any ideas? Any way to activate in safe mode? Any way to copy activation information from my activated installation to my unactivated installation (since they're both on the same hard drive)?

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

• Large mailbox in Outlook 2007 takes ages to index

  - by Reado

  In our company each user has a single mailbox and all email they have ever sent/received is in that mailbox. We don't do archiving to PST and we thought that was the way forward. The problem we now have is if someone switches to another PC for the day and opens Outlook, it has to download all emails first to that PC (cached mode) but even then when they try to search for something, Outlook says items are still being indexed. One user has over 100,000 items to be indexed and it's been saying that for about a week! As a temporary workaround I have turned off instant searching which allows them to search for anything, but it takes time to filter through, and Outlook doesn't exactly indicate if it's still searching for something, so in most cases the user thinks the search isn't working when really it is and it's just taking time to populate the results. I need a solution that allows the mailbox to be indexed really quickly if the user has to login to another PC. Are we best using Online Mode instead of Cached Mode or is there another way around this? Thanks in advance.

  Read the article

• Automatically install driver on headless WHSv1 system

  - by Dan Neely

  I have one of the HP Mediasmart Windows Home Server v1 boxes. It's network port appears to have died a few days ago but the system is not giving any other sign of failure: No activity lights activate on either side of the cable when connected to my gigabit switch; when connected to one of my routers 100 megabit ports the lights turn on but it remains unreachable over the network and my router never lists it as among DHCP clients. I bought a USB-ethernet adapter to temporarily get it back online; but the adapter needs a driver to work which I can't install because the system is headless by design (no video out, no PCI/PCIe slots) with admin access only available via the WHS client or remote desktop. Both of those options require network connectivity and are consequently unavailable. I tried copying the drivers to a flash drive; but Windows either didn't look there or none of the drivers provided were suitable (Win8, Win7, or combined XP and Vista). I've been told that a USB WiFi adapter would have the same driver problem.

  Read the article

• btrfs: can i create a btrfs file system with data as jbod and metadata mirrored

  - by Yogi

  I am trying to build a home server that will be my NAS/Media server as well a the XBMC front end. I am planning on using Ubuntu with btrfs for the NAS part of it. The current setup consists of 1TB hdd for the OS etc and two 2TB hdd's for data. I plan to have the 2TB hdd's used as JBOD btrfs system in which i can add hdd's as needed later, basically growing the filesystem online. They way I had setup the file system for testing was while installing the OS just have one of the HDD's connected and have btrfs on it mounted as /data. Later on add another hdd to this file system. When the second disk was added btrfs made as RAID 0, with metadata being RAID 1. However, this presents a problem: even if one of the disk fails I loose all my data (mostly media). Also most of the time the server will be running without doing any disk access, i.e. the HDD's can be spun down, when a access request comes in this with the current RAID 0 setup both disks will spin up. in case I manage a JBOD only the disk that has the file needs to be spun up. This should hopefully reduce the MTBF for each disk. So, is there a way in which I can have btrfs setup such that metadata is mirrored but data stays in a JBOD formation? Another question I have is this, I understand that a full drive failure in JBOD will lose data on the drive, but having metadeta mirrored across all drives, will this help the filesytem correct errors that migh creep in (ex bit rot?) and is btrfs capable of doing this.

  Read the article

• How to set up Git on remote instance using keys from local machine?

  - by Lucas

  I have a setup where I can ssh into my remote server (ie a Google Compute instance) from my local machine. I used to be able to clone, push, and pull from a repository on my remote instance without adding any keys to my remote instance, nor adding any new keys to my repository online (just the public key from my local machine). I believe the remote instance was using the keys from my local machine to authenticate my Git pushes and pulls. However, the system broke when I reinstalled the OS on my local machine. Now I when I try to connect with the Github server from my remote instance, I get the following: Cannot clone: [lucas@ecoinstance]~/node$ git clone [email protected]:lucasExample/test.git test Cloning into 'test'... Permission denied (publickey). fatal: The remote end hung up unexpectedly Cannot push: [lucas@ecoinstance]~/node/nodetest1$ git status # On branch master # Your branch is ahead of 'origin/master' by 1 commit. # nothing to commit (working directory clean) [lucas@ecoinstance]~/node/nodetest1$ git push Permission denied (publickey). fatal: The remote end hung up unexpectedly Additional info: [lucas@ecoinstance]~/node/nodetest1$ ssh-add -l Could not open a connection to your authentication agent. [lucas@ecoinstance]~/.ssh$ ls authorized_keys known_hosts As you can see, I have no keys on my remote instance. I have never had keys on the remote, and it would push and pull just fine until I re-installed my local OS. I can still clone, push, and pull on my local machine, it is just my remote machine that cannot get authentication. My local OS is Ubuntu 14.04 and my remote OS is Debian Wheezy. Any suggestions would be great. I am not sure how to search for this concept where I can authenticate from a remote instance via my local machine, so any reference are appreciated as well.

  Read the article

• Change which server mailbox is associated with in Exchange 2007

  - by tacos_tacos_tacos

  I have restored and mounted an EDB file onto a new Exchange 2007 Server. However, the old server is still online and although all the mailboxes I need are in the newly-mounted database, in Exchange 2007 System Manager it still shows that the mailbox is associated with the old server. If I try to "Move" the database it actually tries to copy the files from the old server to the new server, which is not necessary because they are already there - and produces and error about the mailbox on the destination already existing. How can I simply tell Exchange (AD?) to use the new server to find the mailbox rather than the old? Edit: I did the restore by taking the old server offline (turning off all Exchange services), copying EDB file to the new server, restoring it with eseutil, and mounting it to the new server. I did it this way in part because I didn't know a better way and in part because I couldn't use move-mailbox as the source location had a horrible Internet connection (which is why Exchange is being moved to the new location). I had to copy the EDB from the old server to a hard disk, go somewhere with a better Internet connection, upload the EDB to the new server.

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• nginx proxy_pass POST 404 errors

  - by Scott

  I have nginx proxying to an app server, with the following configuration: location /app/ { # send to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } Any request for /app goes to :9001, whereas the default site is hosted on :9000. GET requests work fine. But whenever I submit a POST request to /app/any/post/url it results in a 404 error. Hitting the url directly in the browser via GET /app/any/post/url hits the app server as expected. I found online other people with similar problems and added proxy_set_header Host $http_host; but this hasn't resolved my issue. Any insights are appreciated. Thanks. Full config below: server { listen 9000; ## listen for ipv4; this line is default and implied #listen [::]:80 default_server ipv6only=on; ## listen for ipv6 root /home/scott/src/ph-dox/html; # root ../html; TODO: how to do relative paths? index index.html index.htm; # Make site accessible from http://localhost/ server_name localhost; location / { # First attempt to serve request as file, then # as directory, then fall back to displaying a 404. try_files $uri $uri/ /index.html; # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } location /app/ { # rewrite here sends to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; allow ::1; deny all; } }

  Read the article

• Compile php 5.3 ldap extension

  - by toups

  So trying to follow the very un-descriptive guide at my webhost for compiling a new php extension: **Compiling PHP 5.3 extensions You can also compile and load your own extensions. Here's how:** 1. Download and unpack the extension (from PECL, for instance). 2. If the extension is already compiled (most binary PHP loaders will be, for instance), skip to step 6. 3. /usr/local/php53/bin/phpize 4. ./configure --with-php-config=/usr/local/php53/bin/php-config 5. make 6. Copy the module to your .php/5.3/ directory. 7. Assuming your user is called "username" and your module is named "mymodule.so", add the following to your .php/5.3/phprc: extension = /home/username/.php/5.3/mymodule.so Downloaded Openldap stable release online, uploaded the unpacked gzip via ftp to my server, did step 3, 4, 5. Now on step 6 is says "copy the module...". My question is where is the module for me to copy? Sorry if it's obvious and I'm not seeing it; first time compiling a php extension :O

  Read the article

• See former key sequences in vim

  - by Vasiliy Sharapov

  Sometimes I share screen shots and clips of vim usage with others. It would be nice to expand on the part of the status bar highlighted in this picture: I would like some way to make previous key sequences visible as well, such as: y2w jj f[ p 2d - You can see the key sequences leading up to the current one. I'll elaborate on my wish list at the bottom. Is something like this is available as a plugin or vim script? The sheer number of scripts available on vim online makes this hard to find by keyword. Some features I would hope for (but seem improbable): Delimit key sequences with a non-keyboard character instead of space, and a different one for the current command, so y2w jj f[ p 2d might become y2w¦jj¦f[¦p » 2d Replace keys that have a letter alternative with the alternative, such as the right arrow key - ^[[C with the equivalent l. Edit: To clarify, the right arrow key is a valid key in vim, but has no character to represent it, the l key preforms the same function and could/should substitute it. Have previous keystrokes run all the way to the beginning of the line (instead of just one or two), and just have vim's command prompt overwrite it when necessary. Replace some keystrokes with a more elegant alternative, for example hhhhh with 5h or more impressively d2f) with d% (in the appropriate situation).

  Read the article

• Test whether svn REPO changes are reflected in Working Copy

  - by user492160

  Requirement Changes will be made to the REPO directory and this should get updated to wc(working copy) as opposed to the normal way of WC REPO. Senario: My svn repo- /var/www/svn/drupal My checkout-dir/working-copy- /var/www/html/drupalsite So I've done: edited post-commit hook to contain: "/usr/bin/svn update /var/www/html/drupalsite" I won't make any change to svn WC. I'll make changes to svn REPO- /var/www/svn/drupal. After changes are made to svn repo, run "svn commit /var/www/html/drupalsite". This will trigger the post-commit hook. This inturn will run "svn update /var/www/svn/drupal" and thus my WC will get updated with the changes of REPO. Query a. Would the above steps 1-3 help achieve my 'Requirement'? b. I'd need advise on how to test if the above setup works successfully or not. I'm at loss about the success of steps 1-3 the reason why query(a) is present. This is a bit more of a concern for me. NB: I'm new to subversion. Whatever I've configured till now have been done by reading articles online. Reason for query (b) is because I'm not into development. It seems to be a php drupal website and I happen to be setting it up. So I'm not aware as to how to make a "PROPER" change in REPO so that it gets reflected in WC. If reflected, my configs are right and the team can start on development. I manually put a random file/folder into REPO dir for seeing a change in WC and ran steps 1-3 but was of no avail and later on learned that it was NOT the way to make a change to a REPO. Pleas advise. Thanks

  Read the article

• RAID 5 Install on Ubuntu Server 12.04 [closed]

  - by tarabyte

  Environment: Ubuntu Server 12.04, installing from bootable flash drive Error: No root file system is defined. Please correct this from the partitioning menu. I'm trying to set up a personal file server with software RAID 5. I just got three hard drives for this, but haven't found any solid documentation. I'm unsure what the basic way to partition my hard drives is. Can someone upload a screenshot of their "partition disks" screen so that I can compare with mine (attached)? Should I set the bootable flag? Do I need a /home partition? A /boot partition? Should I "Use [my partition] as: Ext4 journaling file system"? Or make that field "physical volume for RAID"? I am an engineer, but I have only a cursory knowledge of all-things-linux. If you know of any good learning resources I'd be happy to hear about those too (that way I don't have to blindly follow deprecated tutorials online). well, image would be here but i don't have a high enough reputation yet (please vote up :)) Thank you, References I've looked into: https://help.ubuntu.com/community/Installation/SoftwareRAID https://help.ubuntu.com/12.04/serverguide/advanced-installation.html http://forevergeeks.com/setup-ubuntu-server-with-raid-5/

  Read the article

< Previous Page | 298 299 300 301 302 303 304 305 306 307 308 309  | Next Page >