Search Results

Search found 31973 results on 1279 pages for 'network library'.

Page 303/1279 | < Previous Page | 299 300 301 302 303 304 305 306 307 308 309 310  | Next Page >

• Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

  - by Chris Drumgoole

  I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• My ASP.NET news sources

  - by Jon Galloway

  I just posted about the ASP.NET Daily Community Spotlight. I was going to list a bunch of my news sources at the end, but figured this deserves a separate post. I've been following a lot of development blogs for a long time - for a while I subscribed to over 1500 feeds and read them all. That doesn't scale very well, though, and it's really time consuming. Since the community spotlight requires an interesting ASP.NET post every day of the year, I've come up with a few sources of ASP.NET news. Top Link Blogs Chris Alcock's The Morning Brew is a must-read blog which highlights each day's best blog posts across the .NET community. He covers the entire Microsoft development, but generally any of the top ASP.NET posts I see either have already been listed on The Morning Brew or will be there soon. Elijah Manor posts a lot of great content, which is available in his Twitter feed at @elijahmanor, on his Delicious feed, and on a dedicated website - Web Dev Tweets. While not 100% ASP.NET focused, I've been appreciating Joe Stagner's Weekly Links series, partly since he includes a lot of links that don't show up on my other lists. Twitter Over the past few years, I've been getting more and more of my information from my Twitter network (as opposed to RSS or other means). Twitter is as good as your network, so if getting good information off Twitter sounds crazy, you're probably not following the right people. I already mentioned Elijah Manor (@elijahmanor). I follow over a thousand people on Twitter, so I'm not going to try to pick and choose a list, but one good way to get started building out a Twitter network is to follow active Twitter users on the ASP.NET team at Microsoft: @scottgu (well, not on the ASP.NET team, but their great grand boss, and always a great source of ASP.NET info) @shanselman @haacked @bradwilson @davidfowl @InfinitiesLoop @davidebbo @marcind @DamianEdwards @stevensanderson @bleroy @humancompiler @osbornm @anurse I'm sure I'm missing a few, and I'll update the list. Building a Twitter network that follows topics you're interested in allows you to use other tools like Cadmus to automatically summarize top content by leveraging the collective input of many users. Twitter Search with Topsy You can search Twitter for hashtags (like #aspnet, #aspnetmvc, and #webmatrix) to get a raw view of what people are talking about on Twitter. Twitter's search is pretty poor; I prefer Topsy. Here's an example search for the #aspnetmvc hashtag: http://topsy.com/s?q=%23aspnetmvc You can also do combined queries for several tags: http://topsy.com/s?q=%23aspnetmvc+OR+%23aspnet+OR+%23webmatrix Paper.li Paper.li is a handy service that builds a custom daily newspaper based on your social network. They've turned a lot of people off by automatically tweeting "The SuperDevFoo Daily is out!!!" messages (which can be turned off), but if you're ignoring them because of those message, you're missing out on a handy, free service. My paper.li page includes content across a lot of interests, including ASP.NET: http://paper.li/jongalloway When I want to drill into a specific tag, though, I'll just look at the Paper.li post for that hashtag. For example, here's the #aspnetmvc paper.li page: http://paper.li/tag/aspnetmvc Delicious I mentioned previously that I use Delicious for managing site links. I also use their network and search features. The tag based search is pretty good: Even better, though, is that I can see who's bookmarked these links, and add them to my Delicious network. After having built out a network, I can optimize by doing less searching and more leaching leveraging of collective intelligence. Community Sites I scan DotNetKicks, the weblogs.asp.net combined feed, and the ASP.NET Community page, CodeBetter, Los Techies,  CodeProject,  and DotNetSlackers from time to time. They're hit and miss, but they do offer more of an opportunity for finding original content which others may have missed. Terms of Enrampagement When someone's on a tear, I just manually check their sites more often. I could use RSS for that, but it changes pretty often. I just keep a mental note of people who are cranking out a lot of good content and check their sites more often. What works for you?

  Read the article

• Create Music Playlists in Windows 7 Media Center

  - by DigitalGeekery

  One of the new features in Windows 7 Media Center is the ability to easily create music playlists without using Media Player. Today we’ll take a closer look at how to create them directly in Media Center. Create Manual Playlists Open Windows Media Center and select the Music Library. From within the Music Library, choose playlists from the top menu.   Then select Create Playlist. Give your new playlist a name, and select Next. Choose Music Library and select Next.    Select “songs” from the top menu, choose the songs for your playlist from your library, and select Next when finished. You can also click Select All to add all songs to your playlist, or clear all to remove them. Note: you can also sort by artist, album, genre, etc. from the top menu.   Now you can review and edit your playlist. Click the up and down pointers to move songs up and down in the playlist, or “X” to remove them. You can also go back and add additional songs by selecting Add More. Click Create when you are finished.   Auto Playlists Windows Media Center also allows you to create six different auto playlists. These are dynamic playlists based on pre-defined criteria. Auto Playlists include All Music, Music added in the last month, Music auto rated at 5 stars, Music played in the last month, Music played the most, and Music rated 4 or 5 stars. These Auto Playlists will change dynamically as your library and listening habits change. Your new music playlists can be found under playlists in the music library. Select play playlist to start the music. Now kick back and enjoy the music from your playlist. Conclusion While earlier versions of WMC allowed you to create playlists, you had to do it through Windows Media Player. This is a nice new feature for music lovers who use WMC and prefer to do everything with a remote. Do you already have playlists that you’ve created in Windows Media Player? Windows Media Center can play those too. If your playlists are in the default Music folder, Media Center will detect them automatically and add them to your Music Library. Plus, any playlists you create in Media Center are also available for Media Player. For more on creating Playlists in Media Player, check out our previous articles on how to create a custom playlist in Windows Media Player 12, and how to create auto playlists in WMP 12. Similar Articles Productive Geek Tips How To Rip a Music CD in Windows 7 Media CenterCreate Custom Playlists in Windows Media Player 12Using Netflix Watchnow in Windows Vista Media Center (Gmedia)How to Create Auto Playlists in Windows Media Player 12Fixing When Windows Media Player Library Won’t Let You Add Files TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos Video preview of new Windows Live Essentials 21 Cursor Packs for XP, Vista & 7 Map the Stars with Stellarium

  Read the article

• DLL Config in Mono

  - by nubela

  Hi, I'm trying to pick up Svn.NET (http://www.pumacode.org/projects/svndotnet/) library for use in my Mono project. I tried compiling its mockapp - svnmockapp project (http://www.pumacode.org/projects/svndotnet/browser/trunk/SvnMockApp) , I am able to get the references right and get it compiled right. I understand that it references 2 other modules libapr (libapr-1.so.0) and svn_client (libsvn_client-1.so.0) , by which I've created PumaCode.SvnDotNet.dll.config in /bin/Debug . That is all I've done to tried to try to get the mockapp at least outputting something to show that it is indeed interfacing SVN. Nevertheless, it is not working. Commands that are entered that doesn't interface SVN works fine: $ mono SvnTest.exe -usage Usage: SvnTest <subcommand> [options] Short Options: ~?.V Subcommands: add, checkout[co], status[st], update[up] For help on subcommands, use the -?/--help subcommand option. Commands that tries to access SVN throws an exception: $ mono SvnTest.exe st An exception was thrown by the type initializer for PumaCode.SvnDotNet.AprSharp.Apr Unhandled Exception: System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.NullReferenceException: Object reference not set to an instance of an object at PumaCode.SvnDotNet.SubversionSharp.SvnMockApp.CmdBase.Run (PumaCode.SvnDotNet.SubversionSharp.SvnMockApp.SubCommand sc, System.String[] args) [0x00000] at (wrapper managed-to-native) System.Reflection.MonoMethod:InternalInvoke (object,object[],System.Exception&) at System.Reflection.MonoMethod.Invoke (System.Object obj, BindingFlags invokeAttr, System.Reflection.Binder binder, System.Object[] parameters, System.Globalization.CultureInfo culture) [0x00000] --- End of inner exception stack trace --- at System.Reflection.MonoMethod.Invoke (System.Object obj, BindingFlags invokeAttr, System.Reflection.Binder binder, System.Object[] parameters, System.Globalization.CultureInfo culture) [0x00000] at System.Reflection.MethodBase.Invoke (System.Object obj, System.Object[] parameters) [0x00000] at PumaCode.SvnDotNet.SubversionSharp.SvnMockApp.Application.Run (System.String[] args) [0x00000] at PumaCode.SvnDotNet.SubversionSharp.SvnMockApp.Application.Main (System.String[] args) [0x00000] Using MONO_DEBUG_LEVEL="debug", we get the following log pasted here. At the tail end of the log, we see this: . . . Mono-INFO: DllImport attempting to load: 'libapr-1'. Mono-INFO: DllImport loading location: 'libapr-1.so'. Mono-INFO: DllImport error loading library: 'libapr-1.so: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport loading library: './libapr-1.so'. Mono-INFO: DllImport error loading library './libapr-1.so: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport loading: 'libapr-1'. Mono-INFO: DllImport error loading library 'libapr-1: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport attempting to load: 'libapr-1'. Mono-INFO: DllImport loading location: 'libapr-1.so'. Mono-INFO: DllImport error loading library: 'libapr-1.so: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport loading library: './libapr-1.so'. Mono-INFO: DllImport error loading library './libapr-1.so: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport loading: 'libapr-1'. Mono-INFO: DllImport error loading library 'libapr-1: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport attempting to load: 'libapr-1'. Mono-INFO: DllImport loading location: 'libapr-1.so'. Mono-INFO: DllImport error loading library: 'libapr-1.so: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport loading library: './libapr-1.so'. Mono-INFO: DllImport error loading library './libapr-1.so: cannot open shared object file: No such file or directory'. Mono-INFO: DllImport loading: 'libapr-1'. Mono-INFO: DllImport error loading library 'libapr-1: cannot open shared object file: No such file or directory'. An exception was thrown by the type initializer for PumaCode.SvnDotNet.AprSharp.Apr I've tried to symlink the appropriate modules in the directory where SvnTest.exe exists, but this still persist. How can I fix this? Did I place the PumaCode.SvnDotNet.dll.config in the wrong folder? (I placed it at /bin/Debug and also tried /bin) What can I do to remedy this? Thank you for your kind help! Much appreciated! Heres the config file: (PumaCode.SvnDotNet.dll.config) <configuration> <dllmap dll="libapr" target="/usr/lib/libapr-1.so.0"/> <dllmap dll="svn_client-1" target="/usr/lib/libsvn_client-1.so.0"/> </configuration>

  Read the article

• Hello World Pagelet

  - by astemkov

  Introduction The goal of this exercise is to give you a basic feel of how you can use Pagelet Producer to proxy a web page We will proxy a simple static Hello World web page, cut one section out of that page and present it as a pagelet that you can later insert on your own application page or to your portal page such as WebCenter Portal space or WebCenter Interaction community page. Hello World sample app This is the static web page we will work with: Let's assume the following: The Hello World web page is running on server http://appserver.company.com:1234/ The Hello World web page path is: http://appserver.company.com:1234/helloworld/ Initial Pagelet Producer setup Let's assume that the Pagelet Producer server is running on http://pageletserver.company.com:8889/pagelets/ First let's check that Pagelet Producer is up and running. In order to do that we just need to access the following URL: http://pageletserver.company.com:8889/pagelets/ And this is what should be returned: Now you can access Pagelet Producer administration screens using this URL: http://pageletserver.company.com:8889/pagelets/admin This is how the UI looks: Now if you connect to the internet via proxy server, you need to configure proxy in Pagelet Producer settings. In the Navigator pane: Jump To - Settings Click on "Proxy" Enter your proxy server configuration: Creating a resource First thing that you need to do is to create a resource for your web page. This will tell Pagelet Producer that all sub-paths of the web page should be proxied. It also will allow you to setup common rules of how your web page should be proxied and will serve as a container for your pagelets. In the Navigator pane: Jump To - Resources Click on any existing resource (ex. welcome_resource) Click on "Create selected type" toolbar button at the top of the Navigator pane Select "Web" in the "Select Producer Type" dialog box and click "OK" Now after the resource is created let's click on "General" sub-item a specify the following values Name = AppServer Source URL = http://appserver.company.com:1234/ Destination URL = /appserver/ Click on "Save" toolbar button at the top of the Navigator pane After the resource is created our web page becomes accessible by the URL: http://pageletserver.company.com:8889/pagelets/appserver/helloworld/ So in original web page address Source URL is replaced with Pagelet Producer URL (http://pageletserver.company.com:8889/pagelets) + Destination URL Creating a pagelet Now let's create "Hello World" pagelet. Under the resource node activate Pagelets subnode Click on "Create selected type" toolbar button at the top of the Navigator pane Click on "General" sub-node of newly created pagelet and specify the following values Name = Hello_World Library = MyLib Library is used for logical grouping. The portals use the "Library" value to group pagelets in their respective UI's. For example, when adding pagelets to a WebCenter Portal space you would see the individual pagelets listed under the "Library" name. URL Suffix = helloworld/index.html this is where the Hello World page html is served from Click on "Save" toolbar button at the top of the Navigator pane The Library name can be anything you want, it doesn't have to match the resource name at all. It is used as a logical grouping of pagelets, and you can include pagelets from multiple resources into the same library or create a new library for each pagelet. After you save the pagelet you can access it here: http://pageletserver.company.com:8889/pagelets/inject/v2/pagelet/MyLib/Hello_World which is : http://pageletserver.company.com:8889/pagelets/inject/v2/pagelet/ + [Library] + [Name] Or to test the injection of a pagelet into iframe you can click on the pagelets "Documentation" sub-node and use "Access Pagelet using REST" URL: This is what we will see: Clipping The pagelet that we just created covers the whole web page, but we want just the "Hello World" segment of it. So let's clip it. Under the Hello_World pagelet node activate Clipper sub-node Click on "Create selected type" toolbar button at the top of the Navigator pane Specify a Name for newly created clipper. For example: "c1" Click on "Content" sub-node of the clipper Click on "Launch Clipper" button New browser window will open By moving a mouse pointer over the web page select the area you want to clip: Click left mouse button - the browser window will disappear and you will see that Clipping Path was automatically generated Now let's save and access the link from the "Documentation" page again Here's our pagelet nicely clipped and ready for being used on your Web Center Space

  Read the article

• Xsigo and Oracle's Storage

  - by Philippe Deverchère

  Xsigo, a virtual network infrastructure provider, has recently been acquired by Oracle. Following this acquisition, one might ask ourselves why it is important to Oracle and how Oracle's storage is going to benefit on the long term from this virtualized infrastructure layer. Well, the first thing to understand is that Virtual Networking addresses both network and storage connectivity. Oracle Virtual Networking, as the Xsigo technology is now called, connects any server to any network and storage, so this is not just about connecting servers to the Internet or Intranet. It is also for a large part connecting servers to NAS and SAN storage. Connecting servers to storage has become increasingly complex in the past few years because of the strong emergence of virtualization at the Operating System level. 50% of enterprise workloads are now virtualized, up from 18% in 2009, resulting in a strong consolidation of various applications in a high density server footprint. At the same time, server I/O capability increased 8x in the last 8 years. All this has pushed IT administrators to multiply the number of I/O connections in the back-end of their physical servers, resulting in a messy and very hard to manage networking infrastructure. Here is a typical view of a rack back-end when no virtual networking is used. We consider that today: - 75% of users have ten or more Ethernet ports per server - 85% of users have two or more SAN ports per server - 58% have had to add connectivity to a server specifically for VMs - 65% consider cable reduction a priority The average is 12 or more ports per server, resulting in an extremely complex infrastructure to manage. What Oracle wants to achieve with its Oracle Virtual Networking offering is pretty simple. The objective is to eliminate the complexity through a dramatic reduction of cabling between servers and storage/networks. It is also to provide a software based management system so that any server can be connected to any network or any storage, on demand, and without physical intervention on the infrastructure. At the end of the day, the picture on the left shows what one wants to get for the back-end of customer's racks: just a couple of connections on each physical server to provide a simple, agile and fast network infrastructure for both storage and networking access. This is exactly what the Oracle Virtual Networking solution does. It transforms a complex, error-prone, difficult to manage and expensive networking infrastructure into a simple, high performance and agile solution for the data center. Practically speaking, and for the sake of simplicity, imagine that each server just hosts a minimal number of physical InfiniBand HCAs (Host Channel Adapter) with two links (for redundancy) onto the Oracle Fabric Interconnect director. Using the Oracle Fabric Manager software, you'll then be able to create virtual NICs and HBAs (called vNIC and vHBA) that will be seen by the servers as standard NICs and HBAs and associate them to networks and storage systems which are physically connected to the back-end of the director through standard Fibre Channel and Ethernet GbE/10GbE ports. In addition to this incredibly simple "at-a-click" connectivity capability, the Oracle Virtual Networking solution offers powerful features such as network isolation, Quality of Service, advanced performance monitoring and non-disruptive reconfiguration, migration and scalability of networking infrastructure. So let's go back now to our initial question: why is Oracle Virtual Networking especially important to Oracle's storage solutions? After all, one could connect any storage in the back-end of the Oracle Fabric Interconnect directors, right? The answer is pretty simple: since Oracle owns both the virtualized networking infrastructure and the storage (ZFS-SA, Pillar Axiom and tape), it is possible to imagine several ways in the future to add value when it comes to connect storage to a virtualized storage network: enhanced storage capabilities, converged management between storage and network, improved diagnostic capabilities and optimized integration resulting in higher performance and unique features/functions. Of course, all this is not going to be done overnight, and future will tell us is which evolutions come first. But there is little doubt that the integration of Xsigo within Oracle is going to create opportunities for Oracle's storage!

  Read the article

• My LAN USB NIC is not working in ubuntu 11.10?

  - by Gaurav_Java

  Today i start my system its seems that my LAN port is not working . so i buy one USB to LAN adapter and i plug in ubuntu system its doen't connect automatically .when i check result lsusb its shows me that there is one DM9601 Ethernet adapter is connected when i click on network information in panel its shows me that there is something " wired NEtwork (Broadcom NetLink BCM5784M gigabit Ethernet PCIe) I think want some driver for that .i don't have any idea how it can be used ? here output of sudo lspci -nn *00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) 00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07) 00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) 00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) 00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) 00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) 00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) 00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) 00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) 00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) 00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) 00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) 00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03) 00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) 00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03) 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) 04:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]* sudo lshw -class network *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 00:1f:16:9a:56:98 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:f4500000-f450ffff *-network DISABLED description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fa:09:02:00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-17-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f4600000-f4601fff *-network description: Ethernet interface physical id: 4 logical name: eth1 serial: 00:60:6e:00:f1:7d size: 100Mbit/s capacity: 100Mbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=dm9601 driverversion=22-Aug-2005 duplex=full firmware=Davicom DM9601 USB Ethernet ip=192.168.1.34 link=yes multicast=yes port=MII speed=100Mbit/s I am using Wimax internet connection which i have to connect from browser . at that time my system is not showing that i am connected to any wired connection. but when i connect internet from other system after getting conneted to internet . when i plug again my USB LAN then its shows that you are conneted to wired connetion. here is screenshot for conneting wimax from browser after connecting to internet network connection shows

  Read the article

• 6 Reasons Why You Can’t Move Your Cell Phone To Any Carrier You Want

  - by Chris Hoffman

  You can buy a laptop or Wi-Fi tablet and use it on Wi-Fi anywhere in the world, so why are cell phones and devices with mobile data not portable between different cellular networks in the same country? Unlike with Wi-Fi, there are many different competing cellular network standards — both around the world and within countries. Cellular carriers also like locking you to their specific network and making it difficult to move. That’s what contracts are for. Phone Locking Many phones are sold locked to a specific network. When you buy a phone from a cellular carrier, they often lock that phone to their network so you can’t take it to a competitor’s network. That’s why you’ll often need to unlock a phone before you can move it to a different cellular provider or take it to a different country and use it on a local provider instead of roaming. Cellular carriers will generally unlock your phone for you as long as you’re no longer in a contract with them. However, unlocking a cell phone you’ve paid for without your carrier’s permission is currently a crime in the USA. GSM vs. CDMA Some cellular networks use the GSM (Global System for Mobile Communications) standard, while some use CDMA (Code-division multiple access). Worldwide, most cellular networks use GSM. In the USA, both GSM and CDMA are popular. Verizon, Sprint, and other carriers that use their networks use CDMA. AT&T, T-Mobile, and other carriers that use their networks are use GSM. These are two competing standards and are not interoperable. This means you can’t simply take a phone from Verizon to T-Mobile, or from AT&T to Sprint. These carriers have incompatible phones. CDMA Restrictions CDMA is more restricted than GSM. GSM phones have SIM cards. Simply open the phone, pop out the SIM card, and pop in a new SIM card to switch carriers. (In reality, it’s more complicated thanks to phone locking and other factors here.) CDMA phones don’t have removable modules like this. All CDMA phones ship locked to a specific network and you’d have to get both your old carrier and your new carrier to cooperate to switch phones between them. In reality, many people just consider CDMA phones eternally locked to a specific carrier. Frequencies Different cellular networks throughout the USA and the rest of the world use different frequencies. These radio frequencies have to be supported by your phone’s hardware or your phone simply can’t work on a network using those frequencies. Many GSM phones support three or four bands of frequencies — 900/1800/1900 MHz, 850/1800/1900 MHz, or 850/900/1800/1900 MHz. These are sometimes called “world phones” because they allow easier roaming. This allows the manufacturer to produce a phone that will support all GSM networks in the world and allows their customers to travel with those phones. If your phone doesn’t support the appropriate frequencies, it won’t work on certain networks. LTE Bands When it comes to newer, faster LTE networks, different frequencies are still a concern. LTE frequencies are generally known as “LTE bands.” To use a smartphone on a certain LTE network, that smartphone will have to support that LTE network’s frequency. Different models of phones are often created to work on different LTE networks around the world. However, phones are generally supporting more and more LTE networks and becoming more and more interoperable over time. SIM Card Sizes The SIM cards used in GSM phones come in different sizes. Newer phones use smaller SIM cards to save space and be more compact. This isn’t a big obstacle, as the different sizes of SIM cards — full-size SIM, mini-SIM, micro-SIM, and nano-SIM are actually compatible. The only difference between them is the size of the plastic card surrounding the SIM’s chip. The actual chip is the same size between all the SIM cards. This means you can take an old SIM card and cut the plastic off until it becomes a smaller-size SIM card that fits in a modern phone. Or, you can take a smaller-size SIM card and insert it into a tray so that it becomes a larger-size SIM card that fits in an older phone. Be aware that it’s very possible to damage your SIM card and make it not work properly by cutting it to the wrong dimensions. Your cellular carrier will often be able to cut your SIM card for you or give you a new one if you want to use an old SIM card in a new phone. Hopefully they won’t overcharge you for this service, too. Be sure to check what types of networks, frequencies, and LTE bands your phone supports before trying to move it between networks. You may have to buy a new phone when moving between certain cellular carriers. Image Credit: Morgan on Flickr, 22n on Flickr

  Read the article

• Configure IPv6 on your Linux system (Ubuntu)

  After the presentation on IPv6 at the first event of the Emtel Knowledge Series and some recent discussion on social media networks with other geeks and Linux interested IT people here in Mauritius, I thought that I should give it a try (finally) and tweak my local network infrastructure. Honestly, I have been to busy with contractual project work and it never really occurred to me to set up IPv6 in my LAN. Well, the following paragraphs are going to shed some light on those aspects of modern computer and network technology. This is the first article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. Let's embrace IPv6 The basic configuration on Linux is actually very simple as the kernel, operating system, and user-space programs support that protocol natively. If your system is ready to go for IP (aka: IPv4), then you are good to go for anything else. At least, I didn't have to install any additional packages on my system(s). We are going to assign a static IPv6 address to the system. Hence, we have to modify the definition of interfaces and check whether we have an inet6 entry specified. Open your favourite text editor and check the following entries (it should be at least similar to this): $ sudo nano /etc/network/interfaces auto eth0# IPv4 configurationiface eth0 inet static  address 192.168.1.2  network 192.168.1.0  netmask 255.255.255.0  broadcast 192.168.1.255# IPv6 configurationiface eth0 inet6 static  pre-up modprobe ipv6  address 2001:db8:bad:a55::2  netmask 64 Of course, you might have to adjust your interface device (eth0) or you might be interested to have multiple directives for additional devices (eth1, eth2, etc.). The auto instruction takes care that your device is enabled and configured during the booting phase. The use of the pre-up directive depends on your kernel configuration but in most scenarios this might be an optional line. Anyways, it doesn't hurt to have it enabled after all - just to be on the safe side. Next, either restart your network subsystem like so: $ sudo service networking restart Or you might prefer to do it manually with identical parameters, like so: $ sudo ifconfig eth0 inet6 add 2001:db8:bad:a55::2/64 In case that you're logged in remotely into your PC (ie. via ssh), it is highly advised to opt for the second choice and add the device manually. You can check your configuration afterwards with one of the following commands (depends on whether it is installed): $ sudo ifconfig eth0eth0      Link encap:Ethernet  HWaddr 00:21:5a:50:d7:94            inet addr:192.168.160.2  Bcast:192.168.160.255  Mask:255.255.255.0          inet6 addr: fe80::221:5aff:fe50:d794/64 Scope:Link          inet6 addr: 2001:db8:bad:a55::2/64 Scope:Global          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 $ sudo ip -6 address show eth03: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000    inet6 2001:db8:bad:a55::2/64 scope global        valid_lft forever preferred_lft forever    inet6 fe80::221:5aff:fe50:d794/64 scope link        valid_lft forever preferred_lft forever In both cases, it confirms that our network device has been assigned a valid IPv6 address. That's it in general for your setup on one system. But of course, you might be interested to enable more services for IPv6, especially if you're already running a couple of them in your IP network. More details are available on the official Ubuntu Wiki. Continue to configure your network to provide IPv6 address information automatically in your local infrastructure.

  Read the article

• After tarball restore my PC (tar xvfpz backup.tgz -C /), my sound card and network are not working. How to detect?

  - by axton hunger

  1 . I have a old laptop I installed Ubuntu 12.04 on. (It was ACER) 2 . I booted into single user mode and backed it up via cd / sudo -i tar cvpzf backup.tgz --exclude=/proc --exclude=/dev --exclude=/lost+found --exclude=/backup.tgz --exclude=/mnt --exclude=/sys / 3 . I installed a fresh copy of Ubuntu 1204 on my new laptop (It is Dell) 4 . I boot into single user mode 5 . I backup the existing /boot directory 6 . I untar my backup to restore on to the Dell sudo tar xvfpz backup.tgz -C / 7 . I restore the previous /boot directory again 8 . I boot it up, and my profile and settings are loaded ok but, Ubuntu shows that there is no Sound Card.. I cannot use unity to drag and change volume. I noticed that the network card also doesnt work. ** How do you make ubuntu recognize changed hardware, if the hardware is already configured for a different laptop? Does anyone know?**

  Read the article

• SignalR Server Error "The ConnectionId is in the incorrect format." with SignalR-ObjC Library

  - by ozzotto

  Before asking a separate question I've done lots of googling about it and added a comment in the already existing stackoverflow question. I have a SignalR Hub (tried both v. 1.1.3 and 2.0.0-rc) in my server with the below code: [HubName("TestHub")] public class TestHub : Hub { [Authorize] public void TestMethod(string test) { //some stuff here Clients.Caller.NotifyOnTestCompleted(); } } The problem persists if I remove the Authorize attribute. And in my iOS client I try to call it with the below code: SRHubConnection *hubConnection = [SRHubConnection connectionWithURL:_baseURL]; SRHubProxy *hubProxy = [hubConnection createHubProxy:@"TestHub"]; [hubProxy on:@"NotifyOnTestCompleted" perform:self selector:@selector(stopConnection)]; hubConnection.started = ^{ [hubProxy invoke:@"TestMethod" withArgs:@[@"test"]]; }; //received, error handling [hubConnection start]; When the app starts the user is not logged in and there is no open SignalR connection. The users logs in by calling a Login service in the server which makes use of WebSecurity.Login method. If the login service returns success I then make the above call to SignalR Hub and I get the server error 500 with description "The ConnectionId is in the incorrect format.". The full server stacktrace is the following: Exception information: Exception type: InvalidOperationException Exception message: The ConnectionId is in the incorrect format. at Microsoft.AspNet.SignalR.PersistentConnection.GetConnectionId(HostContext context, String connectionToken) at Microsoft.AspNet.SignalR.PersistentConnection.ProcessRequest(HostContext context) at Microsoft.AspNet.SignalR.Hubs.HubDispatcher.ProcessRequest(HostContext context) at Microsoft.AspNet.SignalR.PersistentConnection.ProcessRequest(IDictionary`2 environment) at Microsoft.Owin.Mapping.MapMiddleware.<Invoke>d__0.MoveNext() --- End of stack trace from previous location where exception was thrown --- at System.Runtime.ExceptionServices.ExceptionDispatchInfo.Throw() at Microsoft.Owin.Host.SystemWeb.IntegratedPipeline.IntegratedPipelineContext.EndFinalWork(IAsyncResult ar) at System.Web.HttpApplication.AsyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Request information: Request URL: http://myserverip/signalr/signalr/connect?transport=webSockets&connectionToken=axJs EQMZxpmUopL36owSUkdhNs85E0fyB2XvV5R5znZfXYI/CiPbTRQ3kASc3 mq60cLkZU7coYo1P fbC0U1LR2rI6WIvCNIMOmv/mHut/Unt9mX3XFkQb053DmWgCan5zHA==&connectionData=[{"Name":"testhub"}] Request path: /signalr/signalr/connect User host address: User: Is authenticated: False Authentication Type: Thread account name: IIS APPPOOL\DefaultAppPool Thread information: Thread ID: 14 Thread account name: IIS APPPOOL\DefaultAppPool Is impersonating: True Stack trace: at Microsoft.AspNet.SignalR.PersistentConnection.GetConnectionId(HostContext context, String connectionToken) at Microsoft.AspNet.SignalR.PersistentConnection.ProcessRequest(HostContext context) at Microsoft.AspNet.SignalR.Hubs.HubDispatcher.ProcessRequest(HostContext context) at Microsoft.AspNet.SignalR.PersistentConnection.ProcessRequest(IDictionary`2 environment) at Microsoft.Owin.Mapping.MapMiddleware.<Invoke>d__0.MoveNext() --- End of stack trace from previous location where exception was thrown --- at System.Runtime.ExceptionServices.ExceptionDispatchInfo.Throw() at Microsoft.Owin.Host.SystemWeb.IntegratedPipeline.IntegratedPipelineContext.EndFinalWork(IAsyncResult ar) at System.Web.HttpApplication.AsyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) I understand this is some kind of authentication and user identity mismatching but up to now I have found no way of solving it. All other questions suggest stoping the opened connection when the user identity changes but as I mentioned above I have no open connection before the user logs in successfully. Any help would be much appreciated. Thank you.

  Read the article

• C# TCP Hole Punch (NAT Traversal) Library or something?

  - by user293531

  I want to do TCP Hole Punching (NAT Traversal) in C#. It can be done with a rendevouzs server if needed. I found http://sharpstunt.codeplex.com/ but can not get this to work. Ideally i need some method which i give a PortNumber (int) as parameter that after a call to this method is available ("Port Forwarded") at the NAT. It would be also ok if the methode just returns some port number which is then available at the NAT. Has anybody done this in C# ? Can you give me working examples for sharpstunt or something else? Thank you

  Read the article

• Ant and Flex-4 problem, MXMLC.jar not found !

  - by Ali

  Hi all, I updated a flex application from flex 3.5 to flex 4.0. We are using ant for compiling our project and we have a mxmlc task to handle the flex part. After the upgrade, our mxmlc task broke. Here is the task definition: <taskdef resource="flexTasks.tasks"> <classpath> <pathelement path="${FLEX_HOME}/ant/lib/flexTasks.jar"/> <pathelement path="${FLEX_HOME}/lib/flexTasks.jar"/> <fileset dir="${FLEX_HOME}/lib"> <include name="**/*.jar"/> </fileset> </classpath> </taskdef> And here is mxmlc task <mxmlc file="${src}/Main.mxml" output="${build}/main.swf" debug="true" target-player="10" services="../src/main/webapp/WEB-INF/flex/services-config.xml" context-root="/" > <compiler.library-path dir="${lib}"> <include name="*.swc"/> </compiler.library-path> <compiler.library-path dir="${FLEX_HOME}/frameworks/libs"> <include name="*.swc"/> </compiler.library-path> <compiler.library-path dir="${FLEX_HOME}/frameworks/libs/player/10.0"> <include name="*.swc"/> </compiler.library-path> <compiler.library-path dir="${FLEX_HOME}/frameworks/locale"> <include name="**/*"/> </compiler.library-path> </mxmlc> And we are getting: The class not found in jar file: mxmlc.jar I checked the ${FLEX_HOME}/lib folder and I can see the mxmlc.jar file there. I appreciate your comments for resolving this matter, Thanks, -A

  Read the article

• Using RabbitMQ (Java client), is there a way to determine if network connection is closed during con

  - by MItch Branting

  I'm using RabbitMQ on RHEL 5.3 using the Java client. I have 2 nodes (machines). Node1 is consuming messages from a queue on Node2 using the Java helper class QueueingConsumer. QueueingConsumer consumer = new QueueingConsumer(channel); channel.basicConsume("MyQueueOnNode2", noAck, consumer); while (true) { QueueingConsumer.Delivery delivery = consumer.nextDelivery(); ... Process message - delivery.getBody() } If the interface is brought down on Node1 or Node2 (e.g. ifconfig eth1 down), the client (above) never knows the network isn't there anymore. Does RabbitMQ provide some type of configuration on the Java client that can be used to determine if the connection has gone away. Shutting down the RabbitMQ server on Node2 will trigger a ShutdownSignalException, which can be caught and the app can go into a reconnect loop. But bringing down the interface doesn't cause any type of exception to happen, so the code will be waiting forever on consumer.nextDelivery(). I've also tried using the timeout version of this call. e.g. QueueingConsumer consumer = new QueueingConsumer(channel); channel.basicConsume("MyQueueOnNode2", noAck, consumer); int timeout_ms = 30000; while (true) { QueueingConsumer.Delivery delivery = consumer.nextDelivery(timeout_ms); if (delivery == null) { if (channel.isOpen() == false) // Seems to always return true { throw new ShutdownSignalException(); } } else { ... Process message - delivery.getBody() } } but appears that this always returns true (even though the interface is down). I assume registering for the ShutdownListener on the connection will yield the same results, but haven't tried that yet. Is there a way to configure some sort of heartbeat, or do you just have to write custom lease logic (e.g. "I'm here now") in order to get this to work?

  Read the article

• How to Impersonate a user for a file copy over the network when dns or netbios is not available

  - by Scott Chamberlain

  I have ComputerA on DomainA running as userA needing to copy a very large file to ComputerB on WorkgroupB which has the ip of 192.168.10.2 to a windows share that only userB has write access to. There is no netbios or dns resolving so the computer must be refrenced by IP I first I tried AppDomain.CurrentDomain.SetPrincipalPolicy(System.Security.Principal.PrincipalPolicy.WindowsPrincipal); WindowsIdentity UserB = new WindowsIdentity("192.168.10.2\\UserB", "PasswordB"); //Execption WindowsImpersonationContext contex = UserB.Impersonate() File.Copy(@"d:\bigfile", @"\\192.168.10.2\bifgile"); contex.Undo(); but I get a System.Security.SecurityException "The name provided is not a properly formed account name." So I tried AppDomain.CurrentDomain.SetPrincipalPolicy(System.Security.Principal.PrincipalPolicy.WindowsPrincipal); WindowsIdentity webinfinty = new WindowsIdentity("ComputerB\\UserB", "PasswordB"); //Execption But I get "Logon failure: unknown user name or bad password." error instead. so then I tried IntPtr token; bool succeded = LogonUser("UserB", "192.168.10.2", "PasswordB", LogonTypes.Network, LogonProviders.Default, out token); if (!succeded) { throw new Win32Exception(Marshal.GetLastWin32Error()); } WindowsImpersonationContext contex = WindowsIdentity.Impersonate(token); (...) [DllImport("advapi32.dll", SetLastError = true)] static extern bool LogonUser( string principal, string authority, string password, LogonTypes logonType, LogonProviders logonProvider, out IntPtr token); but LogonUser returns false with the win32 error "Logon failure: unknown user name or bad password" I know my username and password are fine, I have logged on to computerB as that user. Any reccomandations

  Read the article

• How do I set up a public server on a network?

  - by tyjkenn

  I am trying to set up a personal cloud server with OwnCloud on Ubuntu. LAMP is all set up. I was able to access it using the external IP address when I connected it directly to the modem, but what if I what if I want my server to share a LAN? I still want it accessible over the internet, but then if I go to the IP address from a web browser, it just tries to log into to router admin tools. The internal IP address works across the LAN, but I want to be able to access it from anywhere. This may be simple and I may be over-thinking it, but how do access my server? The router I am using is ASUS WL-520GU.

  Read the article

• Is there a library for notification/alert in .NET?

  - by sajid.nizami

  I need to design a notifications framework written solely in .Net. I was wondering is there were some libraries already available to ease in creating rules for the notifications. PS: Anything other than SQL Server Notifications please. Note: Notifications as in Emails and SMS notifications.

  Read the article

• Why are UDP messages from outside the network received but not delivered?

  - by Warren Pena

  I have an Ubuntu Server 10.04 application I've developed that receives messages over a UDP port. The ultimate purpose of this application is to receive messages sent from workers' 3G modems out in the field. If use netcat on either another ubuntu Server or my Vista laptop (both on the same LAN as my test machine) to send a message, the message arrives correctly and appears in my application. However, if I go out to my car and use its 3G modem to send a message from the same Vista laptop, it doesn't work. If I run tcpdump -A, I see the message arrive correctly, but it's never delivered to my application. Clearly, the OS is the one making the choice not to deliver the messages (else they wouldn't appear in tcpdump nor would my app receive them when coming from local machines). I have not installed any firewall software on this machine, nor am I aware of anything installed by default that would block the traffic. sudo iptables --list returns Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I'm not too familiar with iptables, but it looks to me like that's telling it to not do anything. What could be going on that's preventing my messages from being delivered?

  Read the article

• How to make sysctl network bridge settings persist after a reboot?

  - by user183394

  I am setting up a notebook for software demo purpose. The machine has 8GB RAM, a Core i7 Intel CPU, a 128GB SSD, and runs Ubuntu 12.04 LTS 64bit. The notebook is used as a KVM host and runs a few KVM guests. All such guests use the virbr0 default bridge. To enable them to communicate with each other using multicast, I added the following to the host's /etc/sysctl.conf, as shown below net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 Afterwards, following man sysctl(8), I issued the following: sudo /sbin/sysctl -p /etc/sysctl.conf My understanding is that this should make these settings persist over reboots. I tested it, and was surprised to find out the following: root@sdn1 :/proc/sys/net/bridge# more *tables :::::::::::::: bridge-nf-call-arptables :::::::::::::: 1 :::::::::::::: bridge-nf-call-ip6tables :::::::::::::: 1 :::::::::::::: bridge-nf-call-iptables :::::::::::::: 1 All defaults are coming back! Yes. I can use some kludgy "get arounds" such as putting a /sbin/sysctl -p /etc/sysctl.conf into the host's /etc/rc.local but I would rather "do it right". Did I misunderstand the man page or is there something that I missed? Thanks for any hints. -- Zack

  Read the article

• Sonicwall routing between multiple subnets on multiple interfaces

  - by Rain

  As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

  Read the article

• Send and Receive JSON using RestClient and Sinatra

  - by lakshmanan

  Hi, I am trying to send a JSON data to a Sinatra app by RestClient ruby API. At client(client.rb) (using RestClient API) response = RestClient.post 'http://localhost:4567/solve', jdata, :content_type => :json, :accept => :json At server (Sinatra) require "rubygems" require "sinatra" post '/solve/:data' do jdata = params[:data] for_json = JSON.parse(jdata) end I get the following error /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient/abstract_response.rb:53:in `return!': Resource Not Found (RestClient::ResourceNotFound) from /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient/request.rb:193:in `process_result' from /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient/request.rb:142:in `transmit' from /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib/ruby/1.8/net/http.rb:543:in `start' from /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient/request.rb:139:in `transmit' from /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient/request.rb:56:in `execute' from /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient/request.rb:31:in `execute' from /Library/Ruby/Gems/1.8/gems/rest-client-1.5.1/lib/restclient.rb:72:in `post' from client.rb:52 All I want is to send JSON data and receive a JSON data back using RestClient and Sinatra..but whatever I try, I get the above error. I m stuck with this for 3 hours. Please help

  Read the article

• What are ProductCode & UpgradeCode & GUID? How to detect if certain application/library is already i

  - by claws

  I've already gone through: http://stackoverflow.com/questions/211192/check-if-the-application-is-already-installed http://stackoverflow.com/questions/488717/detecting-if-a-program-is-already-installed-with-nsis http://nsis.sourceforge.net/Add_uninstall_information_to_Add/Remove_Programs My questions are little more in depth and little more general. So, as you understood my problem is that I want to check if "Certain Applications" are already installed on the user's machine? I'm generating the installer using Advanced Installer. First few questions: What is Upgrade Code? Advanced installer has option, Product Version (identify by Upgrade Code) What is Product Code? Advanced installer Product Version (identify by Product Code) Component is installed : GUID. What is GUID? All the above three has values like this: {49EB7A6A-1CEF-4A1E-9E89-B9A4993963E3} I don't know what these values are but it seems that computer is recognizing software using this kind of strange ID. My required applications are MySQL DBMS MySQL .NET Connector One fact that I discovered is Upgrade Code & Product Code can be extracted from its "msi installer". MySQL Server Installer = mysql-5.1.43-win32.msi Upgrade Code = {49EB7A6A-1CEF-4A1E-9E89-B9A4993963E3} Product Code = {0ECED7D8-FF53-4DC9-958E-C2177F528DE4} GUID (for component Installed) = ???? Uninstall Path = HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\{0ECED7D8-FF53-4DC9-958E-C2177F528DE4} Installer = mysql-5.1.46-win32.msi Upgrade Code = {49EB7A6A-1CEF-4A1E-9E89-B9A4993963E3} Product Code = {EA8FDE5A-2B33-4EDD-B7E7-8D179DF731A5} GUID (for component Installed) = ???? Uninstall Path = HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\{EA8FDE5A-2B33-4EDD-B7E7-8D179DF731A5} Installer = mysql-essential-5.1.46-win32.msi Upgrade Code = {49EB7A6A-1CEF-4A1E-9E89-B9A4993963E3} Product Code = {AD33AF2C-6485-4106-B012-1D9CDC88A454} GUID (for component Installed) = ???? Uninstall Path = HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\{AD33AF2C-6485-4106-B012-1D9CDC88A454} Installer = mysql-essential-5.1.46-win32.msi Upgrade Code = {49EB7A6A-1CEF-4A1E-9E89-B9A4993963E3} Product Code = {9A4DA7EF-A7B9-4282-90AD-10976AA24E69} GUID (for component Installed) = ???? Uninstall Path = HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\{9A4DA7EF-A7B9-4282-90AD-10976AA24E69} Observation from above data: UpgradeCode of a software is constant & is irrespective of its version. ProductCode is version specific & it is used by the MSI internally which is actually reasonable because. MSI allows applications of different versions to be installed side by side. I don't know how to find GUID. MySQL ADO .NET Driver Installer = mysql.data.5.2.5.msi Upgrade Code = --- Product Code = {5FD88490-011C-4DF1-B886-F298D955171B} GUID (for component Installed) = ???? Installer = mysql.data.6.2.2.msi Upgrade Code = --- Product Code = {5FD88490-011C-4DF1-B886-F298D955171B} GUID (for component Installed) = ???? UninstallPath =HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\{5FD88490-011C-4DF1-B886-F298D955171B} Installer = mysql.data.6.2.3.msi Upgrade Code = --- Product Code = {5FD88490-011C-4DF1-B886-F298D955171B} GUID (for component Installed) = ???? Observations from above data: - surprisingly, it couldn't find UpgradeCode from installer of mysql.data.*.msi. I wonder why? This contradicts with my above observation. - ProductCode for all different versions is same here. This again contradicts my above observations. -I still don't know how to find GUID. Now, What exactly are these ProductCode & UpgradeCode & GUID. Which denotes what? Why are above observations contradicting? I don't care about versions. I don't want to depend on Application Name then how do I check if MySQL driver & MySQL ADO .NET. Does detection become simple if they are .NET assemblies? How to do then? I don't want to ship the assemblies with my deployed files.

  Read the article

• Xen HVM networking wont work

  - by Nathan

  I'm trying to get a Xen HVM network working using route however I am failing. Xen PV works fine using Ubuntu but when installing Ubuntu on HVM it fails to pick up the network. I'll let you know now that I'm not that experienced with Xen so I would appreciate any help. vm104 is the HVM thats causing me the problems, here is the configs that I believe should help resolve the problem. [root@eros vm104]# cat vm104.cfg import os, re arch = os.uname()[4] if re.search('64', arch): arch_libdir = 'lib64' else: arch_libdir = 'lib' kernel = '/usr/lib/xen/boot/hvmloader' builder = 'hvm' memory = 6000 shadow_memory = '8' cpu_weight = 256 name = 'vm104' vif = ['type=ioemu, ip=85.25.x.y, vifname=vifvm104.0, mac=00:16:3e:52:3d:fe, bridge=xenbr0'] acpi = 1 apic = 1 vnc = 1 vcpus = 4 vncdisplay = 3 vncviewer = 0 vncconsole = 1 vnclisten = '217.118.x.y' vncpasswd = 'kCfb5S4tE7' serial = 'pty' disk = ['phy:/dev/vpsvg/vm104_img,hda,w', 'file:/home/solusvm/xen/iso/Windows-Server-2008-RC2.iso,hdc:cdrom,r'] device_model = '/usr/' + arch_libdir + '/xen/bin/qemu-dm' boot = 'cd' sdl = '0' usbdevice = 'tablet' pae=1 [root@eros /]# cat /etc/xen/xend-config.sxp | egrep -v "(^#.*|^$)" (xend-unix-server yes) (xend-unix-path /var/lib/xend/xend-socket) (xend-relocation-hosts-allow '^localhost$ ^localhost\\.localdomain$') (network-script network-route) (vif-script vif-route) (network-script 'network-route netdev=eth0') (dom0-min-mem 256) (dom0-cpus 0) (vnc-listen '0.0.0.0') (vncpasswd '') (keymap 'en-us') The Windows install will not pick up the network - I've tried setting the IP manually by using the Xen servers IP as the gateway and setting the main IP in Windows but no luck. If anyone needs any more information let me know and I appreciate any input!

  Read the article

• Is this error caused by a 64-bit library being accessed by a Java program running in a 32-bit JVM?

  - by Mike

  I'm trying to create a simple Java app that uses JNI to call some native functions. I've followed the examples in the JNI Programming Guide and can't seem to get them to work. I have the following Hello World program, written in Java: class HelloWorld { private native void print(); public static void main(String [] args) { new HelloWorld().print(); } static { System.load("/home/mike/Desktop/libHelloWorld.so"); } } I compile it using javac HelloWorld.java, just like normal. Then I run javah -jni HelloWorld, and finally the following: gcc34 -shared -fpic -o libHelloWorld.so -I/<path to JDK>/include -I/<path to JDK>/include/linux HelloWorld.c gcc34 is the name of the GCC program on my machine here at work (I don't control that) and I obviously place the real path to the JDK in that command. When I run my program, using the standard java HelloWorld, I get an error saying the following: Exception in thread "main" java.lang.UnsatisfiedLinkError: /home/mike/Desktop/libHelloWorld.so: /home/mike/Desktop/libHelloWorld.so: wrong ELF class: ELFCLASS64 (Possible causes: architecture word width mismatch) at java.lang.ClassLoader$NativeLibrary.load(Native Method) at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1778) at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1674) at java.lang.Runtime.load0(Runtime.java:770) at java.lang.System.load(System.java:1003) at HelloWorld.<clinit>(HelloWorld.java:8) Could not find the main class: HelloWorld. Program will exit. I know I'm running a 32-bit JVM (and unfortunately, as of right now, I'm not allowed to get a 64-bit JVM). I tried telling GCC to compile in 32-bit mode using the "-m32" option, but we don't have (and again, can't get) what we need for that. Does this sound like a 32/64-bit conflict or something else?

  Read the article

• 10/100 Network performing at 1.5 to 2.0 megabyte per second - is that below normal?

  - by burnt1ce

  This comes out to about 12 to 16 megabit/seond. I've read in forums that people are getting much higher speeds (ie: "40-60 Mb/s" http://forums.cnet.com/5208-7589_102-0.html?threadID=265967). I'm getting my benchmark by having a unmanged 5 port switch connected to a WRT54GS router connect. I'm sending a file from a computer connect to the WRT54GS to another computer that's connect to the unmanaged 5 port switch. Is the linkage of the switch causing this massive overhead? i doubt it. What could explain the slow down? electrical interference?

  Read the article

< Previous Page | 299 300 301 302 303 304 305 306 307 308 309 310  | Next Page >