Search Results

Search found 27295 results on 1092 pages for 'update drivers'.

Page 304/1092 | < Previous Page | 300 301 302 303 304 305 306 307 308 309 310 311  | Next Page >

  • Mouse click-focus wanders in vmPlayer 3.0 dual-monitor

    - by Gary M. Mugford
    Previously, a WinXPSP3 session running on a WinXPSP3 host computer ran perfectly fine in a dual monitor setup. No issues with vmPlayer 2.x. BEFORE updating to vmPlayer 3, the following problem cropped up. When clicking in a single monitor, you would get exactly what you expected. However, when the display was stretched across two monitors, the clicking would be to the left of the mouse cursor. The farther RIGHT you were, the farther left the click would occur. In other words, if you clicked on the system menu of a window in the upper left of a window on the left monitor, you would get the system menu. Move half a screen to your right and the click would be on an item about a quarter of the way over, rather than where you were clicking. And by going all the way to the far right of the right monitor, you could bring up a right-click menu on the far right of the LEFT monitor. I Hope I have described this properly. It's confusing, even in words. In single monitor mode, everything works perfectly fine. If, instead of using either UltraMon or DisplayFusion, you run a single desktop across both monitors (3200x1600), there are no mousing issues. Unfortunately, having two 1600x1200 monitors, that depth of 1600 makes that hack less than useable. My graphic card won't offer anything resembling 3200x1200. vmPlayer 3.0 did not alleviate the situation. The microsoft mouse drivers are up to date and so are the nVidia card drivers. Any ideas?

    Read the article

  • jboss 5.1 mysql connection pooling

    - by boyd4715
    I am using JBOSS 5.1.0.GA, MySQL 5.5 and Hibernate 3.3.1 GA (included with JBOSS) + Spring. My question is do I need to add c3p0 as a data source in my spring/hibernate configuration for connection pooling or are the setting in the JBOSS mysql-ds.xml setting enough. My mysql-ds.xml is the following: <datasources> <local-tx-datasource> <jndi-name>MySqlDS</jndi-name> <connection-url>jdbc:mysql://localhost:3306/ecotrak</connection-url> <driver-class>com.mysql.jdbc.Driver</driver-class> <user-name>ecotrak</user-name> <password>ecotrak</password> <min-pool-size>5</min-pool-size> <max-pool-size>20</max-pool-size> <idle-timeout-minutes>5</idle-timeout-minutes> <exception-sorter-class-name>org.jboss.resource.adapter.jdbc.vendor.MySQLExceptionSorter</exception-sorter-class-name> <!-- should only be used on drivers after 3.22.1 with "ping" support --> <valid-connection-checker-class-name>org.jboss.resource.adapter.jdbc.vendor.MySQLValidConnectionChecker</valid-connection-checker-class-name> <!-- sql to call when connection is created <new-connection-sql>some arbitrary sql</new-connection-sql> --> <!-- sql to call on an existing pooled connection when it is obtained from pool - MySQLValidConnectionChecker is preferred for newer drivers <check-valid-connection-sql>some arbitrary sql</check-valid-connection-sql> --> <!-- corresponding type-mapping in the standardjbosscmp-jdbc.xml (optional) --> <metadata> <type-mapping>mySQL</type-mapping> </metadata> </local-tx-datasource> </datasources>

    Read the article

  • Windows 7 on an EEE PC 901 - Is it a practical change?

    - by Dave
    I am currently running WinXP on my EEE PC 901, and I'm happy to say that it runs really well. But this did not come with out significant manipulation of the OS. Here's the basic steps I took: Install XP Modify registry to install Install bare essential drivers Relocate page file to d:\ (remember, this model has two SSD's, one roughly 3.6gb, and the other roughly 16gb - XP won't run on the bigger drive, only the smaller one) Install remaining drivers skip normal updates, install service pack 2 straight away. modify system registry to place service pack backup folder into new Program Files directory on D drive (where software is being installed). Change My Documents folder to sit on D drive. Install .net framework Install remaining updates and service pack 3 (the hidden backup folders in the c:\Windows directory are deleted after every update as well as the contents of the service pack downloads folder in order to continually free up space). I have also found that Disktrix UltimateDefrag to be brilliant at keeping the system clean and tidy. This is roughly the order I did things in. In this configuration the machine works really well. QUESTION: Can this kind of configuration be implemented with Windows 7 to achieve the same result on this machine? Thanks in advance. Dave.

    Read the article

  • keyboard intermittently stops working even after reinstalling windows 7; possibly a Chrome issue?

    - by neverskipbreakfast
    My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash the ctrl+alt+windows keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) Unplugging & reconnecting keyboard does NOT fix it. Connecting a different keyboard does NOT fix it. That one won't work, either. Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears the keyboard won't work and neither will the icon to pull up the on-screen keyboard. My mouse can click around just fine. I can only log onto a non-password protected account. Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. Clearing my Chrome browsing data stopped the problem from recurring for a week or so. I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. I use Avira free antivirus software, and repeated scans turn up nothing fishy. I suspect it is related to something in Google Chrome because I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

    Read the article

  • Intel DriverInstall issue on HP ProLiant server DL580G5

    - by TomTom
    Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

    Read the article

  • Windows 7 Not Recognizing Camera Nor iPhone as Camera

    - by taudep
    I've been struggling with this one for a few days. I've recently upgraded an older computer to Windows 7 Home Premium. Neither my digital camera (A Canon SD1200IS) nor iPhone are ever detected as cameras, nor ever show up as accessable in Explorer. With the Canon camera, no driver is required. It's supposed to work with the default Windows 7 drivers. However, in the Control Panel's Device Manager, I'm always seeing a yellow icon next to the "Canon Digital Camera" device. I've uninstalled the device and let Windows attempt to reinstall, but it can never find a driver to install. With the iPhone, it's very similar. One big difference, though, is that iTunes can see the iPhone and back it up, etc. However, again when I go to the Device Manager, there's a yellow icon next to the iPhone. I've uninstalled iTunes, reinstalled, rebooted, deleted drivers, and let Window try to reinstall the driver, but it can never find the driver. So there seems to be some correlation that my machine can't detect cameras properly, and that it might be even a lower-level type of driver I'm struggling with. I know that USB however, does work, because I have have an external drive hooked into the machine. I've gone through the web and tried two hours worth of fixes, without success. I feel like if I can get the Canon camera detected, then the iPhone will be on it's way to being fixed too. BTW, I couldn't really find anything of use in the Event viewer. Any and all suggestions welcome.

    Read the article

  • Solaris Fibre Channel target - Configure QLogic QLA2340

    - by growse
    I'm currently trying to set up a small storage system as a fibre channel target. This is for testing, so I'm currently using Solaris (Nexenta) and a QLogic QLA2340 HBA. For some reason, the qlc and qlt drivers don't support the QLA2340, so I'm using the qla2300 driver from QLogic's website. I've also got the scli utility installed for configuration. The HBA is detected by the system. That said, it's not clear how I get from this point to a point where I have a ZFS volume being exposed as an FC target. I was originally following this guide (http://www.youtube.com/watch?v=yzEBd3l7Qn4) but it seems that without the qlc/qlt drivers, Sun's configuration tools won't work. Does that also imply that COMSTAR also won't work? What's the best way to expose an FC target with this setup? Most of the options I'm seeing in scli complain that the port state is LinkDown (it is, I've not plugged anything in yet). Do I have to have my FC client plugged up and working before I can configure the target? Apologies for the slight vagueness of the question, but I'm not overly familiar with the terminology.

    Read the article

  • On dual boot system, Is it possible to use VirtualBox to boot other installed OS?

    - by Derek Ziemba
    I currently run Windows 7 from a 256GB SSD as my Operating System. Lately, for school, I've been using openSUSE linux inside a VirtualBox PC and I'm really liking it. I'm starting to hate even working in Windows. But I can't just abandon Windows. I've been considering dual booting openSUSE and will likely purchase another SSD for openSUSE. Once I have the dual boot set-up, there is going to be times I need to do something quick in the operating system that I'm not currently in. It would be a pain to have to reboot the computer each time I need to switch the OS for a simple task, especially from Windows since it doesn't let you save it's state. From openSUSE, I want to be able to start a VirtualBox Machine using my Windows Drive. And in Windows, I want to be able to start a VirtualBox Machine of my openSUSE Drive. Would this be possible? The issue I'm worried about is drivers. For instance, the OS will be installed on native hardware and have the native hardware's drivers configured. When I try to boot the OS in a VirtualMachine, I feel like the OS is not going to know what to do, and have to reconfigure itself or just not work.

    Read the article

  • Nvidia GTS 360M in Asus laptop shuts off when gaming on external display

    - by mr odus
    I have had this problem on my Asus G51j Intel I5, Nvidia GTS360M graphics card. Just updated the drivers to latest off Nvidias site. Most games I play, If I hook it up through an external monitor(this happens whether it's HDMI or VGA). The laptop hard shuts down after about 20 minutes, give or take. This tends to happen on more graphically intense games like Call of dutys, bioshock. I'm running Windows 7, latest nvidia drivers. Games work fine on my laptops screen, and Movies, general computing work fine on the external displays. The laptop always sits on a cooling pad and the latest time was in front of my AC unit, I ran heatfan or whatever the heat tracking software was, and my temperatures were normal through a shut down. This has been happening for the life of the laptop. I dont play very many games, and even fewer on an external monitor, so this issue doesnt come up much Is it possible I have a faulty graphics card? Is there anything else I can try?

    Read the article

  • How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

    - by McCoy
    Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

    Read the article

  • Error when connecting to shared Windows Printers

    - by TrueDuality
    I'm replacing our Windows 2003 print server with one running on Windows 2008 R2. I have connected and configured all of our printers and can successfully print to them from the server itself. All of the printers are shared and user's have permission to print on all of them. Whenever one of our clients attempts to connect through the shares they receive the following error message: Operation could not be completed (error 0x0000709). Double check the printer name and make sure that the printer is connected to the network. No messages are generated on the client Event Log nor is anything generated on the server. I have reinstalled the drivers as suggested by a few forum posts I came across and it didn't solve the issue. There are twelve different printer drivers and they are all experiencing this issue so I believe it is unrelated to the driver. I have disabled UAC on both the client and server since that has caused so many headaches before, but it too did not solve this problem. Does anyone have any idea what may be causing this?

    Read the article

  • Windows cant repair even with sfc /scannow

    - by GeekyDewd
    Clean install of windows 8, then installed the windows 8.1 update (after all other updates). CBS Log: CBS Log on Google Drive Important pieces of the log: Found: {l:32 b:LrOXAtJDCCTN+z+D1bKj7ogYIrX7sfCCDh+wVBfsrCQ=} Expected: {l:32 b:n520k714Uu3utHa5JGQ6HQYbZphKhlMWq5pEmfnCDuw=} 2014-05-17 21:35:38, Info CSI 00000505 [SR] Cannot repair member file [l:36{18}]"Amd64\CNBJ2530.DPB" of prncacla.inf, Version = 6.3.9600.16384, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type = [l:24{12}]"driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch 2014-05-17 21:35:40, Info CSI 00000506 Hashes for file member \SystemRoot\WinSxS\amd64_prncacla.inf_31bf3856ad364e35_6.3.9600.16384_none_9590ba64d5b91f79\Amd64\CNBJ2530.DPB do not match actual file [l:36{18}]"Amd64\CNBJ2530.DPB" : Found: {l:32 b:LrOXAtJDCCTN+z+D1bKj7ogYIrX7sfCCDh+wVBfsrCQ=} Expected: {l:32 b:n520k714Uu3utHa5JGQ6HQYbZphKhlMWq5pEmfnCDuw=} 2014-05-17 21:35:40, Info CSI 00000507 [SR] Cannot repair member file [l:36{18}]"Amd64\CNBJ2530.DPB" of prncacla.inf, Version = 6.3.9600.16384, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type = [l:24{12}]"driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch 2014-05-17 21:35:40, Info CSI 00000508 [SR] This component was referenced by [l:186{93}]"Microsoft-Windows-Printer-Drivers-Package~31bf3856ad364e35~amd64~~6.3.9600.16384.INF_prncacla" 2014-05-17 21:35:43, Info CSI 00000509 [DIRSD OWNER WARNING] Directory [ml:520{260},l:138{69}]"\??\C:\WINDOWS\System32\WindowsPowerShell\v1.0\Modules\NetSecurity\en" is not owned but specifies SDDL in component Networking-MPSSVC-WMI.Resources, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture = [l:10{5}]"en-US", VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral And: Found: {l:32 b:LrOXAtJDCCTN+z+D1bKj7ogYIrX7sfCCDh+wVBfsrCQ=} Expected: {l:32 b:n520k714Uu3utHa5JGQ6HQYbZphKhlMWq5pEmfnCDuw=} 2014-05-17 21:42:12, Info CSI 00000888 [SR] Cannot repair member file [l:36{18}]"Amd64\CNBJ2530.DPB" of prncacla.inf, Version = 6.3.9600.16384, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type = [l:24{12}]"driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch 2014-05-17 21:42:13, Info CSI 00000889 Hashes for file member \SystemRoot\WinSxS\amd64_prncacla.inf_31bf3856ad364e35_6.3.9600.16384_none_9590ba64d5b91f79\Amd64\CNBJ2530.DPB do not match actual file [l:36{18}]"Amd64\CNBJ2530.DPB" : Found: {l:32 b:LrOXAtJDCCTN+z+D1bKj7ogYIrX7sfCCDh+wVBfsrCQ=} Expected: {l:32 b:n520k714Uu3utHa5JGQ6HQYbZphKhlMWq5pEmfnCDuw=} 2014-05-17 21:42:13, Info CSI 0000088a [SR] Cannot repair member file [l:36{18}]"Amd64\CNBJ2530.DPB" of prncacla.inf, Version = 6.3.9600.16384, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type = [l:24{12}]"driverUpdate", TypeName neutral, PublicKey neutral in the store, hash mismatch 2014-05-17 21:42:13, Info CSI 0000088b [SR] This component was referenced by [l:186{93}]"Microsoft-Windows-Printer-Drivers-Package~31bf3856ad364e35~amd64~~6.3.9600.16384.INF_prncacla" 2014-05-17 21:42:13, Info CSI 0000088c [SR] Repair complete

    Read the article

  • A fatal exception 0E occured at 0028:xxxxxx in VxD IOS(01)

    - by winlin
    I get a blue screen of death in my windows 98 machine every time I boot it. I can't reach to my desktop. The error is like this: A fatal exception 0E occured at 0028:C003CC2F in VxD IOS(01) + 0000156B This was called from 0028:C0082E60 in VxD VKD(01) + 000001D0 I have to then give it a three finger salute to restart the system. There is no other way to shut down the system at this point except pressing the CPU power button. What could be the problem? My windows system.ini is: [boot] oemfonts.fon=vgaoem.fon shell=Explorer.exe system.drv=system.drv drivers=mmsystem.dll power.drv user.exe=user.exe gdi.exe=gdi.exe sound.drv=mmsound.drv dibeng.drv=dibeng.dll comm.drv=comm.drv mouse.drv=mouse.drv keyboard.drv=keyboard.drv *DisplayFallback=0 fonts.fon=vgasys.fon fixedfon.fon=vgafix.fon 386Grabber=vgafull.3gr display.drv=pnpdrvr.drv [keyboard] keyboard.dll= oemansi.bin= subtype= type=4 [boot.description] system.drv=Standard PC mouse.drv=Standard mouse keyboard.typ=Standard 101/102-Key or Microsoft Natural Keyboard aspect=100,96,96 display.drv=Standard PCI Graphics Adapter (VGA) [386Enh] ;device=tddebug.386 ;device=D:\TC\TASM\BIN\WINDPMI.386 ebios=*ebios woafont=dosapp.fon mouse=*vmouse, msmouse.vxd device=*dynapage device=*vcd device=*vpd device=*int13 keyboard=*vkd display=*vdd,*vflatd ConservativeSwapfileUsage=0 Paging=on [NonWindowsApp] TTInitialSizes=4 5 6 7 8 9 10 11 12 13 14 15 16 18 20 22 [power.drv] [drivers] wavemapper=*.drv MSACM.imaadpcm=*.acm ;msvideo.STV680=STV680sg.drv midi=mmsystem.dll wave=mmsystem.dll MSACM.msadpcm=*.acm [iccvid.drv] [mciseq.drv] [mci] cdaudio=mcicda.drv sequencer=mciseq.drv waveaudio=mciwave.drv avivideo=mciavi.drv videodisc=mcipionr.drv vcr=mcivisca.drv MPEGVideo=mciqtz.drv MPEGVideo2=mciqtz.drv [vcache] [MSNP32] [DISPLAY] BusThrottle=1 [network] SSID=1438661605 [vicax] msacm711=74603 msacm811=148933 msacm911=42405 [Sessew] VideoManufacturer=Standard VGA VideoBoard=Standard Display Adapter (VGA) MouseType=0 VidType=0 Mono=0 Ddraw=1 [drivers32] msacm.lhacm=lhacm.acm VIDC.IV50=ir50_32.dll msacm.iac2=C:\WINDOWS\SYSTEM\IAC25_32.AX VIDC.YUY2=msyuv.dll VIDC.UYVY=msyuv.dll VIDC.YVYU=msyuv.dll msacm.msaudio1=msaud32.acm msacm.vorbis=vorbis.acm msacm.l3acm=C:\WINDOWS\SYSTEM\L3CODECA.ACM msacm.sl_anet=sl_anet.acm VIDC.TSCC=tsccvid.dll VIDC.IV41=IR41_32.AX vidc.mpg4=mpg4c32.dll vidc.mp43=mpg4c32.dll msacm.voxacm160=vct3216.acm MSACM.msadpcm=msadp32.acm [TTFontDimenCache] 0 4=2 4 0 5=3 5 0 6=4 6 0 7=4 7 0 8=5 8 0 9=5 9 0 10=6 10 0 11=7 11 0 12=7 12 0 13=8 13 0 14=8 14 0 15=9 15 0 16=10 16 0 18=11 18 0 20=12 20 0 22=13 22

    Read the article

  • SPDIF passthrough not working in Windows 7

    - by adriangrigore
    Hi, I'm running Windows 7 on a computer with an Audigy Platinum eX sound card connected to a surround receiver via optical cabling. Sound works fine when listening to non-surround audio sources, such as windows sounds or MP3. However, when I view a DVD in Media Center and the SPDIF passthrough kicks in, I can only hear an awful noise instead of the movie soundtrack. Also, the receiver does not show the Dolby Digital or DTS symbol, but stays at Dolby Prologic, so it seems it doesn't identify the sound encoding properly. I could switch off SPDIF passthrough and use the sound card's decoder instead, but that's not an option for me since it would create more problems with regular MP3 playback via additional Stereo Receiver which is also connected to the same sound card. I've tried both the default Audigy drivers that come with Windows 7 and the latest drivers from the Soundblaster website, but the problem remains unchanged. Also, I have ensured that the receiver's Dolby Digital decoder is not broken by successfully connecting it to my PS3 to view a Dolby Digital DVD. Besides, SPDIF passthrough was working fine in Vista before I upgraded to Windows 7. Is there anything else I could try?

    Read the article

  • RAID Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. For their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • How do I configure a new (non-OS) raid device under Windows 7?

    - by GregH
    I recently installed 3 new 1TB drives in my Windows 7 (64 bit) system. These are in addition to the 10k rpm disk that I already have running the Windows 7 OS. My intent is to create a RAID 5 volume with the 3 disks. I don't seem to have a problem configuring the bios and creating the resulting 1.9 TB RAID volume. I run in to the problem when I try booting in to Windows. I get a quick flash of a blue screen and then am prompted by windows to do a repair. It tries to repair and then reboots. This sequence lasts indefinitely. If I re-configure the bios back to non-RAID (ACHI) then windows boots fine. The strange thing is that the 1.9 TB volume I configured through the bios actually shows up in windows! Strange since the motherboard is not set up with RAID. I assume that I somehow have to install the RAID drivers from the mobo manufacturer. How do I do this? Is the reason I'm getting the blue screen a result of not having the RAID drivers installed? It's strange because I can find plenty of documentation on how to set up RAID and do a fresh install Windows on to the RAID device, but nothing on how to set up a RAID device on an already running system. Advice is appreciated.

    Read the article

  • How to use the AWUS036H on MacBook Pro with Lion and Backtrack in VM?

    - by Swader
    I have the AWUS036H USB WiFi adapter and have recently upgraded the OSX to Lion. The thing is, there are no drivers for Lion for the AWUS036H, and I would have to boot into 32bit mode every time I want to launch the adapter as per instructions here: http://www.youtube.com/watch?v=n9_HAGi1ce0 I also want to install BackTrack as I deal in networks a lot for my company. While this would be a simple matter on any other laptop, the company issued Macbook does not allow booting into any OS other than MacOSX or Windows with Bootcamp. Now, since dual booting into BT is not an option, I would like Backtrack to run in VM inside my MacOSX Lion - and this it does. It works like a charm inside VirtualBox. But since there are no 64bit drivers for the wifi adapter, Lion doesn't recognize it and cannot install it. This, in turn, means that Backtrack cannot see it even though AWUS036H usually works flawlessly with BT. How can I make my VM-based BT see the wifi adapter even if the parent OS doesn't see it, if at all? Is there a way, or am I better off buying a new WiFi adapter that supports OSX 10.7 such as the AWUS036NHR?

    Read the article

  • Centos does not open port/s after the rule/s are appended

    - by Charlie Dyason
    So after some battling and struggling with the firewall, i see that I may be doing something or the firewall isnt responding correctly there is has a port filter that is blocking certain ports. by the way, I have combed the internet, posted on forums, done almost everything and now hence the website name "serverfault", is my last resort, I need help What I hoped to achieve is create a pptp server to connect to with windows/linux clients UPDATED @ bottom Okay, here is what I did: I made some changes to my iptables file, giving me endless issues and so I restored the iptables.old file contents of iptables.old: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT after iptables.old restore(back to stock), nmap scan shows: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 13:54 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.014s latency). Not shown: 997 filtered ports PORT STATE SERVICE 22/tcp open ssh 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 4.95 seconds if I append rule: (to accept all tcp ports incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 13:58 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.77 seconds *notice it allows and opens port 443 but no other ports, and it removes port 113...? removing previous rule and if I append rule: (allow and open port 80 incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -p tcp --dport 80 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:01 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.014s latency). Not shown: 996 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 5.12 seconds *notice it removes port 443 and allows 80 but is closed without removing previous rule and if I append rule: (allow and open port 1723 incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -p tcp --dport 1723 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:05 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.015s latency). Not shown: 996 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 5.16 seconds *notice no change in ports opened or closed??? after removing rules: iptables -A INPUT -i eth0 -m tcp -p tcp --dport 80 -j ACCEPT iptables -A INPUT -i eth0 -m tcp -p tcp --dport 1723 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:07 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.015s latency). Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 113/tcp closed ident Nmap done: 1 IP address (1 host up) scanned in 5.15 seconds and returning rule: (to accept all tcp ports incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:07 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.87 seconds notice the eth0 changes the 999 filtered ports to 858 filtered ports, 139 closed ports QUESTION: why cant I allow and/or open a specific port, eg. I want to allow and open port 443, it doesnt allow it, or even 1723 for pptp, why am I not able to??? sorry for the layout, the editor was give issues (aswell... sigh) UPDATE @Madhatter comment #1 thank you madhatter in my iptables file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT # ----------all rules mentioned in post where added here ONLY!!!---------- -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT if I want to allow and open port 1723 (or edit iptables to allow a pptp connection from remote pc), what changes would I make? (please bear with me, my first time working with servers, etc.) Update MadHatter comment #2 iptables -L -n -v --line-numbers Chain INPUT (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 9 660 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 3 0 0 ACCEPT all -- eth0 * 0.0.0.0/0 0.0.0.0/0 4 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 5 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 6 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT 6 packets, 840 bytes) num pkts bytes target prot opt in out source destination just on a personal note, madhatter, thank you for the support , I really appreciate it! UPDATE MadHatter comment #3 here are the interfaces ifconfig eth0 Link encap:Ethernet HWaddr 00:1D:D8:B7:1F:DC inet addr:[server ip] Bcast:[server ip x.x.x].255 Mask:255.255.255.0 inet6 addr: fe80::21d:d8ff:feb7:1fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36692 errors:0 dropped:0 overruns:0 frame:0 TX packets:4247 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2830372 (2.6 MiB) TX bytes:427976 (417.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) remote nmap nmap -p 1723 [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-11-01 16:17 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). PORT STATE SERVICE 1723/tcp filtered pptp Nmap done: 1 IP address (1 host up) scanned in 0.51 seconds local nmap nmap -p 1723 localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-11-01 16:19 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000058s latency). Other addresses for localhost (not scanned): 127.0.0.1 PORT STATE SERVICE 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.11 seconds UPDATE MadHatter COMMENT POST #4 I apologize, if there might have been any confusion, i did have the rule appended: (only after 3rd post) iptables -A INPUT -p tcp --dport 1723 -j ACCEPT netstat -apn|grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1142/pptpd There are not VPN's and firewalls between the server and "me" UPDATE MadHatter comment #5 So here is an intersting turn of events: I booted into windows 7, created a vpn connection, went through the verfication username & pword - checking the sstp then checking pptp (went through that very quickly which meeans there is no problem), but on teh verfication of username and pword (before registering pc on network), it got stuck, gave this error Connection failed with error 2147943625 The remote computer refused the network connection netstat -apn | grep -w 1723 before connecting: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd after the error came tried again: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd tcp 0 0 41.185.26.238:1723 41.13.212.47:49607 TIME_WAIT - I do not know what it means but seems like there is progress..., any thoughts???

    Read the article

  • How to get gigabit network speeds on Windows XP?

    - by JB
    We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Dual boot windows 8 pro and windows 7 on XPS 8500 Special Edition

    - by Jesse
    I am trying to install a dual boot with windows 7 premium and windows 8 Pro on an XPS 8500 special edition. I created a new primary partition on my C: drive, inserted the windows 8 install disk, and rebooted my computer from DVD. I select custom install and the dialog box saying "Where do you want to install windows at?" pops up but none of my drives are listed. Please help me determine what is going on. I don't understand why none of my drives are showing up on this menu. Not even the original drive. When I go to load driver and click on the partition I created it tells me "No signed device drivers were found. Make sure the installation media contains the correct drivers, and then click OK." resolved above issue by running setup from the source folder on the install disk instead of booting from DVD. Was able to locate my new partition and start install. It completes the first step of "Copying windows files" just fine but then on the next step "Getting files ready for installation" my computer restarts and attempts to load windows 8 but keeps telling me my pc needs to restart. This keeps going on in an infinite boot loop. Please help, this has been a nightmare!

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • Why does the screen resolution of 1440x900 suddenly disappear from Intel GMA Control Panel?

    - by GeneQ
    I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2. I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've goggled this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

    Read the article

  • Error - "IR Hardware not detected" - but it's installed/working

    - by Robert
    I am trying to do: Settings-TV-Set up TV signal. During this process I am getting the error "IR Hardware not detected." With the remote, I can select the "try again" button (to re-detect) and it tries again, so the remote works. Plugging in the "IR blaster" doesn't change anything. (I wouldn't expect any difference, but I read a post which said you needed that. I will get Media Center to change channels if I can get that working - but first things first.) I was able to do the setup months ago when I had cable. and everything was fine. I just got DirecTV. (BTW - During the above process, Media Center detects the signal coming in on channel 3. Windows XP Media Center SP3. The TV Tuner card is a Pinnacle TCTV HD PCI. Everything - and I mean everything - has the latest firmware and drivers - as of 4 months ago when I fixed a different problem. So I DON"T WANT TO HEAR the standard answer to check drivers/firmware. THANK YOU.) Thanks for any help.

    Read the article

< Previous Page | 300 301 302 303 304 305 306 307 308 309 310 311  | Next Page >