Search Results

Search found 9611 results on 385 pages for 'low power'.

Page 306/385 | < Previous Page | 302 303 304 305 306 307 308 309 310 311 312 313  | Next Page >

• Hardware freeze during disk activity

  - by Thomi

  I built myself a linux-based NAS. It has several drives of various sizes and ages in an LVM configuration, with 800GB or so of data. The data is served using a simple samba server. This was working flawlessly, but after physically moving it, it has developed a strange fault: Whenever I do something on the server to cause disk activity, the entire machine freezes hard. This has the effect of killing any open network connections to the box, and generally making it useless. If I leave the machine for a few minutes it seems to come right again, but obviously this isn't really a solution. There are no error or warning messages in syslog, or the kernel logs. If I power the machine on, and leave it, it runs for several days without locking up. After that time I stopped testing. It doesn't freeze instantly - obviously it doesn't freeze while booting, and I can normally log in via SSH and start poking around in a few log files for a couple of minutes before it dies. My question is: What diagnostic tests can I run to determine the casuse?

  Read the article

• Webapp in Jetty can't find properties file after running a couple days

  - by Cuga

  I have a webapp running in Jetty on Mac OS 10.6. After a few days of it running and without the server losing power or rebooting, it seems to stop working saying it can't find a properties file. This properties file is included inside the .war file deployed to the /webapps directory. If I restart Jetty as the superuser the web service works again just fine. Can anyone lend any advice to what's going on and how I can fix it? The error being shown when it isn't working is: Problem accessing /my-web-service. Reason: INTERNAL_SERVER_ERROR Caused by: java.lang.NullPointerException at com.company.service.Dao.readFromPropertiesFile(BwDao.java:35) at com.company.service.ServletHandler.doGet(ProxyClass.java:66) ... at org.mortbay.jetty.HttpConnection.handle(HttpConnection.java:404) at org.mortbay.io.nio.SelectChannelEndPoint.run(SelectChannelEndPoint.java:410) at org.mortbay.thread.QueuedThreadPool$PoolThread.run(QueuedThreadPool.java:582) Here's where the properties files exist that it's trying to read from the .war file: And this is how the properties are being read from the classpath: Properties properties = new Properties(); properties.load(Thread.currentThread().getContextClassLoader().getResourceAsStream( "app.properties")); Again, this does work just fine if I have just restarted the server, but it seems to fail after running a few days.

  Read the article

• Computer sending data while turned off

  - by Nicklas Ansman

  I have a some what strange problem (which could have and easy and obvious solution for all I know). My problem is that when I've booted ubuntu (now 10.4 but same problem with 9.10) and turns it off it starts sending a HUGE amount of data via the ethernet cable, so much in fact that my router can't handle it and stops responding. As far as I can tell the computer is completely turned off with no fans spinning. I can add that if I boot windows I do not have this problem, just when exiting ubuntu. There are two "fixes" for my problem: Pull the ethernet cable until the next boot Turn off power to the PSU and wait for the capacitors to unload Is there anyone who knows what could be going on? I'd be happy to post some logs or conf-files. Currently I'm using the ethernet port on my motherboard which is a Asus P6T Deluxe V2 with an updated version of the BIOS (maybe not the latest but since it only happens when I've been in ubuntu I don't wanna mess with the BIOS too much). Regards Nicklas ---------Update 1---------- The router is a D-Link DIR 655 with the latest firmware. ---------Update 2---------- I've now reinstalled ubuntu (with 10.4) and I still experience the same problem.

  Read the article

• Laptop Randomly Turning On and Off

  - by Ian Mallett

  So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

  Read the article

• Intermittent extrememly long response times when downloading documents

  - by pap

  I have a Java web application running om Tomcat 7 with an Apache httpd 2.2 fronting with mod_jk/AJP. One part of the application is serving files (up to 4mb size). Now, normally this all runs very smooth with stable, low response-times. However, in rare instances (<0.1% of downloads), the downloadtime will go beyond 1 minute. After activating the ThreadStuckValve in Tomcat, I can see that the long responses seem to be stuck at org.apache.tomcat.jni.Socket.sendbb(Native method) i.e network I/O. At most, these long-running downloads take 5 minutes, which I strongly suspect is because of the default 300 second timout in Apache 2.2 (http://httpd.apache.org/docs/2.2/mod/core.html, "TimeOut directive"). To me, this looks like network problems. The Apache timeout (if that is what is kicking in at the 5 minute mark) indicates that ACK packets are not being transmitted correctly. My questions are what could be causing this? Closed browser at receiving end but socket not signaled as closed properly? Packet loss or some other network failure in transit? Where would I start troubleshooting this? We're running Tomcat and Apache on Windows server 2008-R2 in a vmware virtualized server.

  Read the article

• Mac mini simple customized, Mac mini server or other?

  - by microspino

  I'm in front of a big IT choice for my little office and I need some advice. We have 5 users, 1 super user, 1 HP500 DesignJet Plotter, other 4 laser printers, 1 HP Fax/Print/Scan/Copy machine. All the clients are XP Sp3 boxes. We would like to: centralize and share 90Gb of files using a Dropbox (this way we will have LAN sync of local working directories + internet backup + access our files wherever we are). centralize our plotter, printers and fax machine backup all the workstations share outlook calendar and tasks run 24x7 saving some energy Of course this setup It's just the first step to a more serious and creative network management of our office, so we are open to new ideas. The budget vary from 400€ to 900€, we are not tech gurus but at least one of us is a power user close to become a geek. I've read some articles on macminicolo about a mac mini either normal or with snow leopard server. I heard about Windows Home Server too on the lifehacker website but I'm in a sort of analysis - paralysis can You help me?

  Read the article

• Ubuntu - No gnome-panels, no right-click, no internet, no hotkeys

  - by Darthfett

  Hey guys, I've been using Ubuntu (Maverick 10.10) on my desktop (ATI Radeon 5830) for about 3 weeks now, but all of a sudden I am unable to even use my computer. As soon as I start up, I see my desktop, with icons, but I don't see any gnome-panels, and I'm unable to get any options if I right-click. I can start programs by double clicking them. I also cannot get an internet connection. I've tried restarting gnome-panel by killing it, using Ctrl+Alt+5 to switch to a terminal (I don't have a shortcut to one on my desktop, and no hotkeys will work), but no luck. Restarting my computer has no effect upon this (I have to manually cut the power, since I don't know the terminal command). As far as I know, I have not made any changes, and I've never had any problems in the past. This started when I was playing Minecraft, but my internet crapped out, and no amount of re-trying the connection would work. I know it was my computer, as my brother's was working fine in the other room. Any clues as to what's going on? I'm more than willing to troubleshoot.

  Read the article

• Best practices for thin-provisioning Linux servers (on VMware)

  - by nbr

  I have a setup of about 20 Linux machines, each with about 30-150 gigabytes of customer data. Probably the size of data will grow significantly faster on some machines than others. These are virtual machines on a VMware vSphere cluster. The disk images are stored on a SAN system. I'm trying to find a solution that would use disk space sparingly, while still allowing for easy growing of individual machines. In theory, I would just create big disks for each machine and use thin provisioning. Each disk would grow as needed. However, it seems that a 500 GB ext3 filesystem with only 50 GB of data and quite a low number of writes still easily grows the disk image to eg. 250 GB over time. Or maybe I'm doing something wrong here? (I was surprised how little I found on the subject with Google. BTW, there's even no thin-provisioning tag on serverfault.com.) Currently I'm planning to create big, thin-provisioned disks - but with a small LVM volume on them. For example: a 100 GB volume on a 500 GB disk. That way I could more easily grow the LVM volume and the filesystem size as needed, even online. Now for the actual question: Are there better ways to do this? (that is, to grow data size as needed without downtime.) Possible solutions include: Using a thin-provisioning friendly filesystem that tries to occupy the same spots over and over again, thus not growing the image size. Finding an easy method of reclaiming free space on the partition (re-thinning?) Something else? A bonus question: If I go with my current plan, would you recommend creating partitions on the disks (pvcreate /dev/sdX1 vs pvcreate /dev/sdX)? I think it's against conventions to use raw disks without partitions, but it would make it a bit easier to grow the disks, if that is ever needed. This is all just a matter of taste, right?

  Read the article

• Best usage for a laptop being used as a desktop without removable batteries

  - by Senseful

  After reading the information on http://batteryuniversity.com, I realize that one of the best ways to permanently damage a lithium ion battery is to use the battery at a high temperature while it's fully charged. This is exactly what happens when you use the computer as if it were a desktop computer, since leaving it plugged in will keep the battery at 100% and using the computer will heat up the battery. This is why it's recommend to remove the battery from your laptop if you are using it is this scenario. My question is what would you do if the laptop doesn't have removable batteries (e.g. a MacBook Pro)? Should I use some kind of charge cycle such as: charge to 80%, unplug the power chord, use the laptop until it reaches 20%, then repeat the cycle by charging to 80% again? If so, which values should I use instead of 80% and 20%? (I think charging to 80% is better than 100% because of the damage that a hot battery at 100% can do, but I just made the figure 80% up, and I'm sure there's a better number to strive for which is backed by science.) I've read many of the articles on batteryuniversity.com, but couldn't find anything pertaining to this. Update: What about doing something like charge (or discharge) it to 50%, then plug it in and turn on settings which use the battery as much as possible (e.g. brightness all the way up, wi-fi on, etc.), in order to try to maintain the battery at 50% (i.e. the rate it is charging is the same as it is discharging). This will probably heat up the battery, but would make it so you don't need to constantly plug and unplug the laptop. The one bad thing is that you are taking up more charge cycles which would decrease the battery life, thus I'm not sure this is a good idea.

  Read the article

• DPMS does not work: the monitor is not switched off

  - by bortzmeyer

  I have a monitor which was properly switched off by my Debian PC when unused. I attached it to another machine and, this times, it is never switched off. In /etc/X11/xorg.conf, I have: Section "Monitor" Identifier "Generic Monitor" Option "DPMS" It is recognized when X11 starts: (II) Loading extension DPMS ... (II) VESA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display ... (**) Option "dpms" (**) VESA(0): DPMS enabled The operating system is Debian stable "lenny". The graphics card is: 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrate d Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 2a6f Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fe900000 (32-bit, non-prefetchable) [size=512K] I/O ports at b080 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-Capabilities: [d0] Power Management version 2 X11 is: X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny2) Current Operating System: Linux ludwigVII 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:3 8 UTC 2009 i686 Build Date: 08 June 2009 09:12:57AM

  Read the article

• nginx: dump HTTP requests for debugging

  - by Alexander Gladysh

  Ubuntu 10.04.2 nginx 0.7.65 I see some weird HTTP requests coming to my nginx server. To better understand what is going on, I want to dump whole HTTP request data for such queries. (I.e. dump all request headers and body somewhere I can read them.) Can I do this with nginx? Alternatively, is there some HTTP server that allows me to do this out of the box, to which I can proxy these requests by the means of nginx? Update: Note that this box has a bunch of normal traffic, and I would like to avoid capturing all of it on low level (say, with tcpdump) and filtering it out later. I think it would be much easier to filter good traffic first in a rewrite rule (fortunately I can write one quite easily in this case), and then deal with bogus traffic only. And I do not want to channel bogus traffic to another box just to be able to capture it there with tcpdump. Update 2: To give a bit more details, bogus request have parameter named (say) foo in their GET query (the value of the parameter can differ). Good requests are guaranteed not to have this parameter ever. If I can filter by this in tcpdump or ngrep somehow — no problem, I'll use these.

  Read the article

• Server 2003 PDC DNS not working..Failover server is...

  - by Seth

  In the midst of trying to utilize proc power, i create a fault tolerant DNS server a while ago. Since, Ive been trying to add another controller for exchange. So I thought I would revert back to a single primary DNS for the meantime and now Im balancing on a thread. The server i thought I uninstalled DNS, is still acting as DNS. And now the PDC does not resolve. Can anybody walk me through, Im overwhelmed and cant think straight... Im afraid if anyone restarts their machine they wont have internet. Update Ok so from the beginning. I was configuring Exchange on a new server 2008. How it happened I dont know, but it started to not resolve DNS. (exclamation mark on NIC) even though everything was static. So ultimately I decided to remove the server from the problem, because I noticed DNS was in disarray if I used the DNS IP of the first server. This is when I tested with nslookup on each DNS server. I had uninstalled DNS from the second server, but nslookup was still resolving with that IPaddress, which has me all wound up cause I dont understand. So, since the first DNS server isn't resolving, Im assuming if the second one isnt configured right I'll loose internet. Im just confused and dont know where to start troubleshooting...

  Read the article

• Number of routers in small community lock up and require reboot.

  - by Anthony Hiscox

  I live in a small town which has one primary ISP. Lately I have noticed that a number of wireless routers have been locking up and requiring a reboot before allowing any connections. This has affected two of my routers, my work router, and a few others. In all cases wired continued to function as usual. Often wireless clients can see the SSID but simply won't connect. I can only think of a few possibilities and was hoping someone here might be able to point me in the right direction: Our ISP is well known to be flaky, something they are doing is causing this, what that might be I have no clue it as seems to affect the wireless only. There's a power issue in town, given our remote location and reputation for crap electrical, this seems reasonable. Only one router was plugged in to a UPS, and I'm not sure of the quality. There is some bug in all the different firmware for every one of these routers (all different). That doesn't seem reasonable, unless; it's an unknown (or known) exploit or DoS of some sort being launched by a massive team of ninjas hell bent on forcing us all to be tethered to our walls by ethernet cables or; it's just been a coincidence and I'm just paranoid (this has some weight, I mean read 4 again). Anyone else experience similar issues and have some tips?

  Read the article

• Asus K50I sound issues

  - by MrStatic

  I have an Asus K50IJ (Bestbuy) laptop and have issues with my sound. Speakers themselves work fine but when I plug into the headphone jack it auto mutes the front channel and no sounds comes out of either the speakers or the headphones. If I then unmute the channel I get sound from both the speakers and the headphones. alsamixer shows the Headphone channel as all grayed out. /etc/modprobe.d/alsa-base.conf I have tried snd-hda-intel model="asus-laptop" and snd-hda-intel model="asus" In Sound Preferences I have gone to output and changed the Connector to 'Analog Headphones' that results in no sound from either speakers or headphones. As one forum suggested I tried to comment out blacklist snd_pcsp in the blacklist.conf which resulted in no change. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Santa Cruz Operation Device 1043 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at fe9f4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel

  Read the article

• DDoS nulling to some ips and other options?

  - by Prix

  I am looking for some information in regards DDoS in the follow scenario: I have a server that is behind a Cisco Guard and it will be DDoS'ed, I only care about a set list of IPS that by not means are the attackers. Is it possible to null all other ips but this list to actually get any response to my server or in the long run no matter what I do if they have enough DDoS power I will just go down like a flie ? Is there any recommended company out there that can actually cope with a DDoS ? My server will mainly run several clients that will get connected to a external server and all it needs access to is my local MySQL the the private network so I can access it. There will be no other services runnings such as web or ftp etc at least not to the external ips of the server if i ever have to have any of these service they will be on the private network. The MySQL will be available externally only to 1 safe ip not known by anyone but me and internally at localhost + private network. Are there any solutions ?

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• Server freezes while installing Redhat Enterprise Linux Server 6

  - by eisaacson

  We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

  Read the article

• Which CPU for XEN - LAMP testbed - Budget

  - by deploymonkey

  Dear serverfault knowledgeables, im in a decision dilemma right now, which I can't resolve due to lack of hands on experience. I need to build a testbed for basically virtualizing a LAMP application (os'ses not yet decided) including server side calculations. I'll opt for XEN since it seems better supported by cloud hosters at the moment. The hardware is for a proof of concept for a startup doing saas and might be used for closed live alpha/beta later on. After testing, the testbed might be a) deployed as a colocated white box server b) used as workstation Single socket is enough. We want to have ECC memory for reliability, this excludes most of the consumer line at intel. If intel CPU, then threaded cpu (HT) is preferred have at least 16 gig ram If justified by price and reliability is not too bad, a high quality desktop MB instead of a server MB would be worth a try It came down to the opteron 6128 vs. the xeon 5620 for me after a lot of research, but I don't necessarily have to be right. Which CPU is preferrable, concerning TCO (MB price, power requirements 24/7...) , Opteron 6128 or Xeon 5620? Which one offers better performance in real world applications? (Do You have any other suggestions I probably overlooked?) Thank You for Your consideration

  Read the article

• Block SMTP session with sender domain which doesn't itself accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the declared sender's domain has an MX which refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. Note that I'm not, as some commenters have assumed, talking about checking whether the SMTP client will receive messages. The check I want is whether the declared sender's domain (regardless of who the current SMTP client is) will accept SMTP connections from here. In other words: when we get around to sending a message back, we'll need the sender's domain to accept SMTP connections; I want to do that check before accepting the incoming session. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• Remote paging with Nagios when network is down and email won't work -- cellular modems and alternatives

  - by Quinten

  What is the best option for remote paging when network services are down? I'm looking for a solution that can let me know when network services are down during off-hours only, and especially when email/smtp services are out. Therefore, it needs to be redundant to our network and power supply. I'm imagining a cellular modem is one option. What's the price range for these? Is anybody using them and feel that they are worth the cost? I'm imagining that it's something we would end up sending an emergency page ~ 1x/month at most, so I'd like the pricing to reflect that--I don't mind a high per-page cost as long as it has a low recurring cost. Another option would be to expose at least one server to remote ping, and run a check script on a remote server. Are there paid options for this? Currently, we run Nagios on a Linux VM on a Windows 2008 Hyper-V host. It would be great if the solution would work in that environment, but I know it's tricky with external devices, and we could move Nagios to a standalone workstation if needed.

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• Aging SBS needs updates / Thoughts for one-off, off-line complete backup?

  - by tcv

  Hey guys, So, we checked out the status of an SBS 2003 at one of our more recent, spend-averse clients and found it to be woefully out-of-date. Scary out of date. I think it's running IE2. Ok, maybe not that far back. Anyway, I was thinking that I could use some kind of disk-imaging software to image the four IDE drives within and, in the event the server gets some kind of Update Induced Indigestion, I could completely restore. Usually my go-to software for this is Acronis, but my client will likely balk at a $500 price tag for a one-off backup with their server product. I had thought we could use the boot media from, say, Backup & Recovery 10 to take an off-line image of all the drives. According to their CHAT tech support, however, it will not work. I pressed for the technical reasons and they said they'd email me. They haven't emailed me. They still might. This server is running SBS 2003, pre sp2. It's got four IDE disks. One is a Basic disk, which contains the O/S. The others are bound as a dynamic disk. You might ask: "Don't they already have backup software?" They do! Backup Exec, a very low-end version that won't even do VSS. I don't know much about BE, but it seems to me that if the worst were to happen, it would mean building a new server O/S, installing BE (if the media is available), then restoring. Would it even work? I can take the system down for hours to do a backup and my goal here is a pretty dead-simple restore if the worst happens. Any and all suggestions are exciting. m

  Read the article

• w2k3 AD DC Demotion fails with "no other AD DC for that domain can be contacted"

  - by Kstro21

  i've a small office with a single w2k3 sp2 DC(bad idea, but it is real), now, i want to make a clean install of that pc, so, i got another one, install w2k3 sp2, add it to the domain, dcpromo and set it to be a GC, untill now everything is ok, then tried to dcpromo in the primary DC, but it fails with The box indicating that this domain controller is the last controller for the domain mydomain.com is unchecked. However, no other Active Directory domain controllers for that domain can be contacted. Do you wish to proceed anyway? If you click Yes, any Active Directory changes that have been made on this domain controller will be lost. So, i started to move all the roles to the new server as described here, when all was ok with the roles, i tried doing the same, but got the same result. Tried moving the DNS to the new server, but it doesn't make difference. Shutdown to the old server, then tried to log into a workstation, but it fails saying the domain is not available, also coudln't add new workstation to the domain, so i have to power on the old server again. So, if i successfully move all the roles and dns to the new server: why dcpromo give such message in the old server? why if i shutdown the old server the domain is not available?? if i successfully move all the roles and dns to the new server, and i click yes when dcpromo give warning in the old server, will i lose all users, computers, ou, etc.? am i missing some steps to make this work?? hope you can help me thanks

  Read the article

• how to block spam email using Microsoft Outlook 2011 (Mac)?

  - by tim8691

  I'm using Microsoft Outlook 2011 for Mac and I'm getting so much spam I'm not sure how to control it. In the past, I always applied "Block Sender" and "Mark as Junk" to any spam email messages I received. This doesn't seem to be enough nowadays. Then I've started using Tools Rules to create rules based on subject, but the same spammer keeps changing subject lines, so this isn't working. I've been tracking the IP addresses they also seem to be changing with each email. Is there any key information I can use in the email to apply a rule to successfully place these spam emails in the junk folder? I'm using a "Low" level of junk email protection. The next higher level, "high", says it may eliminate valid emails, so I prefer not to use this option. There's maybe one or two spammers sending me emails, but the volume is very high now. I'm getting a variation of the following facebook email spam: Hi, Here's some activity you have missed. No matter how far away you are from friends and family, we can help you stay connected. Other people have asked to be your friend. Accept this invitation to see your previous friend requests Some variations on the subject line they've used include: Account Info Change Account Sender Mail Pending ticket notification Pending ticket status Support Center Support med center Pending Notification Reminder: Pending Notification How do people address this? Can it be done within Outlook or is it better to get a third party commercial software to plug-in or otherwise manage it? If so, why would the third party be better than Outlook's internal tools (e.g. what does it look for in the incoming email that Outlook doesn't look at)?

  Read the article

< Previous Page | 302 303 304 305 306 307 308 309 310 311 312 313  | Next Page >