Search Results

Search found 30249 results on 1210 pages for 'virtual machine languages'.

Page 308/1210 | < Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >

• How to add an extra language input to Android?

  - by bgever

  Is it possible to add extra languages to Android? My current Android phone only supports English and Chinese language input. I would like to have Dutch also, as I can use it for word completion. The question on top of that is, how to switch easily between these languages in the text input (keyboard) GUI?

  Read the article

• FTP through HAProxy

  - by Menda

  I have a machine, which is the Host and has HAProxy installed in it and working. Then I have a Guest KVM virtual machine running inside the Host with an IP 192.168.122.152. I installed an FTP server in the Guest machine with VSFTPD. From the Host, if I try the command $ ftp -p 192.168.122.152, works perfectly and I can connect to the Guest FTP. I need to remark that this FTP is configured as passive, but both passive and active connections are working from the Host. This is an extract of part of /etc/vsftpd.conf in the Guest: # Passive mode connect_from_port_20=NO tcp_wrappers=YES listen_address=192.168.122.152 pasv_enable=YES pasv_promiscuous=NO port_enable=YES port_promiscuous=NO pasv_max_port=10000 pasv_min_port=10250 Now it's time to make it accessible from outside, so I configure /etc/haproxy/haproxy.cfg like this: listen FTP_Default *:21 server ftp01 192.168.122.152 check port 21 inter 10s rise 1 fall 2 listen FTP_Range *:10000-10250 server ftp01 192.168.122.152 check port 21 inter 10s rise 1 fall 2 But if I try to connect from other machine in internet $ ftp -p $PUBLICIP, it only responds: Connected to <PUBLICIP>, but it doesn't ask for the login and password. Something in the HAProxy config must be wrong, because it's the only point where it fails. By the way, I tried to adapt my configuration to this one in this blog. Thanks.

  Read the article

• VHD Boot failure in Hyper-V (Win7 boot from vhd)

  - by stuck_again

  I've have a virtual machine with a VHD image that I've copied from Windows 7 to the Hyper-V server. This image was created on Windows 7 (Windows 7 64-bit), and I'm using it on Windows 7 as boot image. Starting this virtual machine with the Hyper-V Manager gives this error: "Boot failure. Reboot and Select proper Boot device or Insert Boot Media in selected Boot device." What do I need to do to boot from this vhd in Hyper-V?

  Read the article

• Symantec Backup Exec Error on backup

  - by AliGibbs

  Recently we have moved some of servers from real servers- into virtual servers. Since then, we are getting errors like the following: Error category : Resource ErrorsError : e000fed1 - A failure occurred querying the Writer status. For additional information regarding this error refer to link V-79-57344-65233 This is happening on the virtual servers and also the real servers now. Looked on google and found some information- like running "vssadmin list writers" however none of these are showing an error.

  Read the article

• James - mail server configuration help needed

  - by Chaitanya

  Hi, I am trying to setup James mail server on a linux machine. The linux machine has public static ip address assigned. I installed James and added in the config.xml added the servername as mydomain.com. In the DNS for mydomain.com, I have created a A-record, say mx.mydomain.com, which corresponds to the ipaddress of the above mail server machine. Then added mx.mydomain.com as MX record for mydomain.com. In James, I have created a new user test. Then from gmail, I sent a mail to [email protected]. The mail is not received back and it didn't even bounce back. The linux machine is behind a firewall with only 22, 80, 8080 ports open for external network. My question here is, Do I require do open any other ports on the firewall so that the mail I send from gmail arrives to James? If it's not the port problem, any views on solving this issue? I don't want to send mails from this server. It's only for receiving the mails.

  Read the article

• Sending microphone input over Remote Desktop 7.0

  - by Taylor Price

  I am using Remote Desktop 7 (the new version that came out with Windows 7) to control a Windows XP Pro machine. I have selected "Record from this computer" in the Remote Audio settings. When I connect to the machine, go to the control panel, open the sound panel, and go to the audio tab, I find that the default sound playback device is "Microsoft RDP Audio Driver". However, there is no default sound recording device. As expected, my IP phone thinks there is no recording device. If I am sitting in front of the computer with a mic plugged in, it works just fine. Has anybody else been able to get this work appropriately? Is there anything that I have to setup on the XP machine to get this working? Thanks in advance. Edit: As John T pointed out below, you have to be connecting to a Windows 7 Enterprise or Ultimate machine for this to work. I've also found out that Multi-monitor support has the same requirement.

  Read the article

• Disable local delivery in Sendmail

  - by Luke P M

  I am using Sendmail on a Centos server to send email for PHP scripts, but the problem is that mail is delivered to a local mailbox on the machine rather than what is specified in the MX records for the domain - which actually point to another machine I use for email. I would like sendmail to not try and locally deliver mail for the domain the machine is setup for, is there a simple way to disable local delivery? The domain is not in the local-host-names file. I've already done lots of googling and I have looked at: http://serverfault.com/questions/26934/sendmail-configuration-to-not-deliver-mail-to-local-machine http://serverfault.com/questions/65365/disable-local-delivery-in-sendmail But either there is no answer or it is not suitable. I don't want to relay to another server, i just want it to send mail regardless of domain. To provide an example: I have two servers, one is the mail server at mail.example.com and a web server which is example.com, when I use the smtp service on the web server it currently routes mail to a local mailbox on example.com, but it should be going to mailboxes on mail.example.com Output of sendmail -bt returns: ADDRESS TEST MODE (ruleset 3 NOT automatically invoked) Enter 3,0 [email protected] canonify input: info @ example . com Canonify2 input: info Canonify2 returns: info canonify returns: info parse input: info Parse0 input: info Parse0 returns: info ParseLocal input: info ParseLocal returns: info Parse1 input: info Parse1 returns: $# local $: info parse returns: $# local $: info

  Read the article

• Security as a Service (SecaaS) for Amazon EC2

  - by Dave

  I'm looking for a security as a service (SecaaS) provider or open source solution for Amazon EC2 instances, however I can't seem to find much on Google or elsewhere so was wondering if anyone knows where I could find this service? Ideally I'm looking for something that offers virtual firewalls, email and web security and virtual spam prevention. If anyone has any information on SecaaS i'd appreciate it, Thanks in advance

  Read the article

• What disk image should I use with VirtualBox, VDI, VMDK, VHD or HDD?

  - by Sorin Sbarnea

  Latest versions of VirtualBox supports several formats for virtual disks, but they forgot to provide a comparison between them. VDI VMDK VHD HDD Now, I am interested about a recommendation or comparison that considers the following: be able to use dynamic sizing be able to have snapshots be able to move my virtual machine to another OS or even another free virtualization solution with minimal effort (probably something that would run fine on Ubuntu). performance

  Read the article

• Appcrash and possible malware

  - by Chris Lively

  First off, I'm running MS Intune Endpoint Protection. It is completely up to date. On 10/25 @ 11:53PM I came across a site that caused Intune to freak out: Microsoft Antimalware has detected malware or other potentially unwanted software. For more information please see the following: http://go.microsoft.com/fwlink/?linkid=37020&name=Trojan:Win64/Sirefef.B&threatid=2147646729 Name: Trojan:Win64/Sirefef.B ID: 2147646729 Severity: Severe Category: Trojan Path: file:_C:\Windows\System32\consrv.dll Detection Origin: Local machine Detection Type: Concrete Detection Source: Real-Time Protection User: NT AUTHORITY\SYSTEM Process Name: C:\Windows\explorer.exe Signature Version: AV: 1.115.526.0, AS: 1.115.526.0, NIS: 10.7.0.0 Engine Version: AM: 1.1.7801.0, NIS: 2.0.7707.0 I, of course, elected to simply delete the file. Since then my machine has been randomly giving an error about "Host Process for Windows Services" stopped working. There are generally two different pieces of info: Description Faulting Application Path: C:\Windows\System32\svchost.exe Problem signature Problem Event Name: BEX64 Application Name: svchost.exe Application Version: 6.1.7600.16385 Application Timestamp: 4a5bc3c1 Fault Module Name: StackHash_52d4 Fault Module Version: 0.0.0.0 Fault Module Timestamp: 00000000 Exception Offset: 000062bdabe00000 Exception Code: c0000005 Exception Data: 0000000000000008 OS Version: 6.1.7601.2.1.0.256.27 Locale ID: 1033 Additional Information 1: 52d4 Additional Information 2: 52d47b8b925663f9d6437d7892cdf21b Additional Information 3: ed24 Additional Information 4: ed24528f3b69e8539b5c5c2158896d3e and Description Faulting Application Path: C:\Windows\System32\svchost.exe Problem signature Problem Event Name: APPCRASH Application Name: svchost.exe Application Version: 6.1.7600.16385 Application Timestamp: 4a5bc3c1 Fault Module Name: mshtml.dll Fault Module Version: 9.0.8112.16437 Fault Module Timestamp: 4e5f1784 Exception Code: c0000005 Exception Offset: 00000000002ed3c2 OS Version: 6.1.7601.2.1.0.256.27 Locale ID: 1033 Additional Information 1: 3e9e Additional Information 2: 3e9e8b83f6a5f2a25451516023078a83 Additional Information 3: 432a Additional Information 4: 432a0284c502cce3bbb92a3bd555fe65 Intune claims the machine is clean. I've also tried some of the online scanners like trendmicro, all of which claimed the system is clean. Finally, I tried the "sfc /scannow" and it said all was good. I left my machine on after I left last night and there were about 50 of those messages. Ideas on how to proceed?

  Read the article

• Virtualhosts, maintain existing applications

  - by savageguy

  I host several applications by IP in subfolders (http://ip/app). I would also now like to host a domain, I've been able to setup the virtual hosts so that the domain loads properly in it's document root however the rest of my applications stop working and point to the same virtual host document root of the domain. How do I maintain my existing setup so all other requests behave the same?

  Read the article

• TFS 2010 : Unable to add Project to a collection

  - by Scott

  This morning I'm trying to setup Team Foundation Server 2010 to demo for my team. As this is just a demo, I thought I would install it on my Windows 7 machine which also serves as my development machine. My development machine uses Visual Studio 2008 Team Suite. I installed Team Explorer 2008 and then reapplied SP1. Finally I installed and setup TFS 2010. TFS by default gave me administrator privileges. I started up Visual Studios, and connected up to the Collection just fine. However, I'm unable to create a new project and get the follow error message: "TF30172: You are trying to create a team project either without required permissions or with an older version of team Explorer. Contact your project admin..." To check to permissions, I used my home computer which is running Visual Studio 2010. On this machine I was able to connect up to the same TFS instance and create a project no problem. So it looks as though it is a team explorer problem, but everywhere on the web people are saying not only am what I'm trying to do possible, but they have done it themselves. What am I missing to add a project to TFS 2010 under Visual Studio 2008?

  Read the article

• Move database from SQL Server 2012 to 2008

  - by Rich

  I have a database on a SQL Sever 2012 instance which I would like to copy to a 2008 server. The 2008 server cannot restore backups created by a 2012 server (I have tried). I cannot find any options in 2012 to create a 2008 compatible backup. Am I missing something? Is there an easy way to export the schema and data to a version-agnostic format which I can then import into 2008? The database does not use any 2012 specific features. It contains tables, data and stored procedures. Here is what I have tried so far: I tried "tasks" - "generate scripts" on the 2012 server, and I was able to generate the schema (including stored procedures) as a sql script. This didn't include any of the data, though. After creating that schema on my 2008 machine, I was able to open the "Export Data" wizard on the 2012 machine, and after configuring the 2012 as source machine and the 2008 as target machine, I was presented with a list of tables which I could copy. I selected all my tables (300+), and clicked through the wizard. Unfortunately it spends ages generating its scripts, then fails with errors like "Failure inserting into the read-only column 'FOO_ID'". I also tried the "Copy Database Wizard", which claimed to be able to copy "from 2000 or later to 2005 or later". It has two modes: 1) "detach and attach", which failed with error: Message: Index was outside the bounds of the array. StackTrace: at Microsoft.SqlServer.Management.Smo.PropertyBag.SetValue(Int32 index, Object value) ... at Microsoft.SqlServer.Management.Smo.DataFile.get_FileName() 2) SQL Management Object Method which failed with error "Cannot read property IsFileStream.This property is not available on SQL Server 7.0."

  Read the article

• VMWare Converter - Remote Linux Install P2V

  - by Zed Said

  I am trying to get what I thought was an easy process working. Here is my situation. I have a remote linux server (running Debian) that I would like to turn into a VM so that I can do testing on it rather than the production server. I downloaded VMWare Converter. I went to the "convert machine" wizard, chose Powered-on machine, entered my remote machine details. Clicking next shows that it correctly connects to my remote linux box. Now, on the next screen, for Destination type, it enters "WMWare Infrastructure virtual machine", and I can't change this. This is where I am stuck. Why do I need another sever to convert with? Is this where my VM gets sent to? And why can't I just convert the VM and save it on the computer that I am running the converter program on? If I do have to use a vmware infrastructure destination, I am confused at what ESX is, why and how I use it. Any help with this process would be more than appreciated!

  Read the article

• Cannot Change "Log on through Terminal Services" in Local Security Policy XP from Server 2008 GP

  - by Campo

  This is a mixed AD environment, Server 2003 R2 and 2008 R2 I have a 2003 AD R2 and a 2008 R2 AD. GPO is usually managed from the 2008 R2 machine. I have a RD Gateway on another server as well. I setup the CAP and RAP to allow a normal user to log on to the departments workstation. I also adjusted the GPO for that OU to allow Log on trhough Remote Desktop Gateway for the user group. This worked on my windows 7 workstation. But unfortunately the policy is a different name in XP "allow log on through Terminal Services" I can get through right into the machine but when the log on actually happens to the local machine i get the "Cannot log on interactively" error. This is set in (for the local machine) Secpol.msc Local Security Policy "user rights assignment" but is controlled by the GPO in Computer Configuration Policies Security Settings Local Policies "User Rights Assignment" Do I simply need to adjust the same setting on the same GPO but with a server 2003 GP editor? Feel like that could cause issues... Looking for some direction. Or if anyone has run into this issue yet. UPDATE Should this work? support.microsoft.com/kb/186529 Still seems like I will have the issue as the actual GP settings for Log on through Terminal Services is still different between Server 2008 R2 and 2003 R2.... Another Thought: Should I delete the GPO made for the department and remake it with the 2003 R2 server? I have no 2008 specific settings as the whole department runs XP other than myself. If that's a solution I will move my computer out of the department as a solution... Thoughts?

  Read the article

• How do I improve my incremental-backup performance?

  - by Alistair Bell

  I'm currently using the traditional rsync+cp -al method to create incremental/snapshot backups of our server tree. The backups are going onto a pair of eight-disk towers connected to the backup machine (a Sandy Bridge machine with 16 GB of RAM, running CentOS 5.5) via four eSATA connections (four disks per connection). Each disk is a regular 2 TB disk, so we have 32 TB of disk space connected to the backup machine. We're backing up about 20 TB of data on the servers with this. The problem is that each daily backup is taking more than 24 hours, and the real time-killer isn't the actual rsync, but the time it takes to perform a cp -al of the tree locally on the backup machine. It's taking more than 12 hours just to make the shadow copy of the tree, and as far as I can tell the performance backlog is at the disk (top shows the cp using a lot of RAM but not a lot of CPU and mostly in uninterruptible-sleep state) We have the server data split into four major volumes (and a few minor ones), and each of these backups runs in parallel (with some offsets in the cron to try to get some disks' cp done first). There are two volumes on the backup drive, both striped LVM volumes of 16 TB each. So obviously I need to improve the performance because it's unusable as it stands. The first question is: when CentOS 6 comes out, with support for btrfs, will making snapshots of subvolumes with btrfs substantially increase this performance? The second is: is there a way, with ext3 or something else supported in CentOS 5 or 6, to 'encourage' it to put the directories/inodes in one part of a volume (which could happen to be the part that's on an SSD, via LVM) and the files in another? That would presumably solve the problem, but I don't know of ways to hint ext3 like that.

  Read the article

• Server migration

  - by vinayrks

  I have to do a virtual host to another virtual host transfer , Both of them are hosted on Rackspace , OS (Red hat 4 ). client is using this server for hosting more than 10 live sites , lots of files in /var/www. I transferred all files and db from old to new , My questions: what else should I need to worry about ? how to transfer all cron job too? is I need to make entry of each site on httpd.conf or rackspace will do it , during IP swapping ?

  Read the article

• "chown mysql:mysql /data/tmp" command

  - by Mellon

  I am on a Linux ubuntu machine with MySQL installed. If there is a MySQL installation on a Ubuntu machine, I saw some people doing the following thing: sudo chown mysql:mysql /data/tmp I get confused, I know the meaning of the above command, which is to change the owner of /data/tmp to user 'mysql' and change the group of it to 'mysql' group. But (my questions): 1. Why would one run the above command? If I create a table in my_db database, by default, there will be .frm, .MYD, and .MYI files (data files) be created automatically by MySQL under /var/lib/mysql/my_db/ . So, does the above command changes the default MySQL data directory to /data/tmp/ instead of /var/lib/mysql/my_db/? Basically, I would like to know the purpose and effect of the above command. (better with examples) 2. Where does the 'mysql' owner and group come from? Does the installation of MySQL on a Linux machine automatically create the 'mysql' user and group? or People need to manually create a mysql account for the linux machine?

  Read the article

• Amazon AWS EC2 + Puppet, get Puppet to know AWS instance tags

  - by Piotr Jasiulewicz

  I am having a problem with my AWS deployment, fairly new to AWS and Puppet. So coming to my question - can you distinguish puppet nodes with AWS machine tags or CNAME domains? A little background about the plan: have multiple clusters of machines, one php cluster, one legacy php cluster, one java cluster, one perl cluster control configuration with puppet - still pretty new to puppet but as a developer I like the idea of being able to version control configuration of servers have autoscaling enabled on those clusters - obviously the main benefit of the cloud that makes the much hight cost when it comes to any reasonable performance worth it (those amazon machines are slower than my phone...) deployment controlled by Capistrano, this makes things a lot easier So in AWS you get those super nasty public/private machine dns's... no way you can identify machines on those. In order to easer the problem, seams like AWS want's you to tag everything - so I did. Found a script that makes a CNAME record for each machine with the tag "ShortName" thanks to the Route53 API. Every machine has a ShortName tag that becomes its CNAME, unfortunately puppet still resolves the private dns name. I'd like to have node 'perl-cluster'{} in puppet, anyone any clue ho to achieve this? Thanks

  Read the article

• MySQL socket connections working, but not port connections

  - by Neil

  I installed MySQL community 5.1.45 on my Snow Leopard 10.6, using the pkg from their site. I had previously installed a MySQL binary from entropy.ch. In the previous installation, the connections were working fine before I upgrade to Snow Leopard. In Snow Leopard, both the installations are problematic. Using an app called Sequel Pro, if I connect with the socket operation, it connects properly. However, a standard connection with the same credentials doesn't work. From what I've understood, socket connections happen on the machine itself between processes, whereas normal connections occur over the network/ports, in this case a loopback to my machine, since the server and client are both on the same machine. My new CakePHP installation isn't being able to connect to the db with the root credentials I provided. Btw, I've been starting the MySQL server using the Preference Pane. When I tried running mysqld from terminal, it gave me: 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test mysqld: Can't change dir to '/usr/local/mysql-5.1.45-osx10.6-x86_64/data/' (Errcode: 13) 100323 1:54:37 [ERROR] Aborting 100323 1:54:37 [Note] mysqld: Shutdown complete mbp is the name of my machine. How do I fix this so that my webserver can connect to the mysql server?

  Read the article

• When I log on to my company desktop, I log on to a domain. How is this domain name installed?

  - by learnerforever

  Hi, When I have to work on my machine in company, I have noticed that I log on to a domain (named on the basis of company name) and not really on that computer. From, what I understand, this has a few advantages, the primary being that I just need one password for the domain and can work through any of the machines in company. My questions are : What software on desktop/network have to be installed so that the desktop recognizes and gives me option of logging into a domain. I would guess that a software can be installed on desktop, and there we can configure the IP address of domain server of company and port number, which handles authentication. Is this correct? This takes me to another question that how are softwares installed on end machines in a company. Going to each machine physically and installing looks very unweildy from administrator point of view. An obvious solution would be to install softwares (and updates) over network. My question on this are: What protocols,keywords come into picture when administrator installs OS,softwares,updates from his administrator machine to end machine through network. Thanks,

  Read the article

• MAC addresses on dual-NIC mainboards

  - by Tom O'Connor

  Here's a weird problem. We've got a number of devices with dual-NIC mainboards. Some are Realtek NICs, which suck. Some are Intel e1000s, which don't. I've just noticed on 2 machines, one is an Intel NIC, one is a Realtek, that when I put the MAC address of one machine into the dhcpd.conf file on our DHCP server to get it to PXE boot the machine into a rebuild environment, initially everything is fine. The server gets a DHCP allocation, and PXE boots into the Ubuntu preseed enviroment. On one or two machines, it gets as far as Ubuntu's DHCP network configuration, and fails. If i pull up a busybox shell (on tty2 on the installing machine), and run ip link, I can see that the UP flag is set on the other NIC. Here's some stuff. host xeon16-ghz240-gb48-node1 { hardware ethernet BC:AE:C5:07:1F:18; filename "pxelinux.0"; next-server 192.168.123.80; } That's what's in dhcpd.conf This is what ip link on the evil machine looks like. Only one NIC is actually connected (deliberately). As you can see, the NIC that's in the dhcpd config, is not marked as UP, and the link that is UP, isn't the one in DHCP. So far I've seen this on two brands of dual-NIC configuration. Does anyone know 1) what's causing it, and b) What we can do about it?

  Read the article

• Windows Terminal Server: occasional memory violation for applications

  - by syneticon-dj

  On a virtualized (ESXi 4.1) Windows Server 2008 SP2 32-bit machine which is used as a terminal server, I occasionally (approximately 1-3 event log entries a day) see applications fail with an 0xc0000005 error - apparently a memory access violation. The problem seems quite random and only badly reproducable - applications may run for hours, fail with 0xc0000005 and restart quite fine or just throw the access violation at startup and start flawlessly at the second attempt. The names of executables, modules and offset addresses vary, although a single executable tends to fail with same modules and the same memory offset addresses (like "OUTLOOK.EXE" repeatedly failing on module "olmapi32.dll" with the offset "0x00044b7a") - even across multiple user's logons and with several days passing without a single failure inbetween. The offset addresses seem to change across reboots, however. Only selective executables seem affected by the problem, although I may simply not be seeing a sufficient number of application runs from the other ones. I first suspected a possible problem with the physical machine's RAM, but ruled this out as a rather unlikely cause - the memory comes with ECC and I've already moved the virtual machine across several times, without any perceptable change. I've seen that DEP was enabled in "OptOut" mode on this machine: C:\Users\administrator>wmic OS Get DataExecutionPrevention_SupportPolicy DataExecutionPrevention_SupportPolicy 3 and tried changing the policy to OptIn via startup options: bcdedit.exe /set {current} nx OptIn but have yet to see any effect - I also would expect Outlook 12 or Adobe Reader 9 (both affected applications) to play well with DEP. Any other ideas why the apps may be failing?

  Read the article

• Issues with Server 2012 using DFSR running on Hyper-V 2012

  - by Bryan

  We have a number of Server 2012 systems, all of which run virtualised on Hyper-V 2012 server. We are having problems with two such virtual instances, both of which are used as file servers, whereby they occasionally stop responding to requests to serve files to clients. After logging on to the server, attempts to shut it down gracefully fail (no error, it just fails to acknowledge a shutdown request). Recovery is a case of power cycling the server(s) from the Hyper-V console. These two servers don't server a large number of users (one serves no more than 6 users, and the other serves around 20 users), they are in the same domain, but on different physical hardware (and at different sites). They don't lock up at the same time. They both use DFSR to replicate a fairly large amount of data between themselves (200GB) over ADSL connections, this is working fine, and we have been using DFSR to do this on the previous two generations of server OS we have used (Server 2008 R2 and Server 2003 - both of which were physical installs however). Today, when one of the servers crashed, I noticed an entry in the event log, which looked similar to the following: Log Name: Application Source: ESENT Date: 27/11/2012 10:25:55 Event ID: 533 Task Category: General Level: Warning Keywords: Classic User: N/A Computer: HAL-FS-01.example.com Description: DFSRs (1500) \\.\E:\System Volume Information\DFSR\database_C8CC_101_CC00_EC0E\ dfsr.db: A request to write to the file "\\.\E:\System Volume Information\ DFSR\database_C8CC_101_CC00_EC0E\fsr.log" at offset 4423680 (0x0000000000438000) for 4096 (0x00001000) bytes has not completed for 36 second(s). This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. When the server started up again, I went to find the event log entry to investigate further and found that the event log entry was no longer there (I assume it was in memory but failed to write to disk before the server was powered off, for the reason mentioned in the message). I found the above message by searching back further in the event log. Both of these virtual servers have their E: volumes fully allocated as opposed to dynamically expanding, and there are no other issues on any of the other virtual servers (which include server 2012, server 2008 R2 and Ubuntu 12.04 x64). There are no signs of IO, memory or CPU starvation on the host systems. I've used performance counters on the affected virtual servers to monitor memory usage (including non paged pool usage), as well as CPU and network utilisation, and none of these show any signs of trouble when the issue arises. I would have thought our configuration isn't that uncommon, so I'm wondering if anyone else has seen this, and managed to resolve the problem?

  Read the article

• openssl client authentication error: tlsv1 alert unknown ca: ... SSL alert number 48

  - by JoJoeDad

  I've generated a certificate using openssl and place it on the client's machine, but when I try to connect to my server using that certificate, I error mentioned in the subject line back from my server. Here's what I've done. 1) I do a test connect using openssl to see what the acceptable client certificate CA names are for my server, I issue this command from my client machine to my server: openssl s_client -connect myupload.mysite.net:443/cgi-bin/posupload.cgi -prexit and part of what I get back is as follow: Acceptable client certificate CA names /C=US/ST=Colorado/L=England/O=Inteliware/OU=Denver Office/CN=Tim Drake/[email protected] /C=US/ST=Colorado/O=Inteliware/OU=Denver Office/CN=myupload.mysite.net/[email protected] 2) Here is what is in the apache configuration file on the server regarding SSL client authentication: SSLCACertificatePath /etc/apache2/certs SSLVerifyClient require SSLVerifyDepth 10 3) I generated a self-signed client certificate called "client.pem" using mypos.pem and mypos.key, so when I run this command: openssl x509 -in client.pem -noout -issuer -subject -serial here is what is returned: issuer= /C=US/ST=Colorado/O=Inteliware/OU=Denver Office/CN=myupload.mysite.net/[email protected] subject= /C=US/ST=Colorado/O=Inteliware/OU=Denver Office/CN=mlR::mlR/[email protected] serial=0E (please note that mypos.pem is in /etc/apache2/certs/ and mypos.key is saved in /etc/apache2/certs/private/) 4) I put client.pem on the client machine, and on the client machine, I run the following command: openssl s_client -connect myupload.mysite.net:443/cgi-bin/posupload.cgi -status -cert client.pem and I get this error: CONNECTED(00000003) OCSP response: no response sent depth=1 /C=US/ST=Colorado/L=England/O=Inteliware/OU=Denver Office/CN=Tim Drake/[email protected] verify error:num=19:self signed certificate in certificate chain verify return:0 574:error:14094418:SSL routines:SSL3_READ_BYTES:tlsv1 alert unknown ca:/SourceCache/OpenSSL098/OpenSSL098-47/src/ssl/s3_pkt.c:1102:SSL alert number 48 574:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:/SourceCache/OpenSSL098/OpenSSL098-47/src/ssl/s23_lib.c:182: I'm really stumped as to what I've done wrong. I've searched quite a bit on this error and what I found is that people are saying the issuing CA of the client's certificate is not trusted by the server, yet when I look at the issuer of my client certificate, it matches to one of the accepted CA returned by my server. Can anyone help, please? Thank you in advance.

  Read the article

< Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >