Search Results

Search found 5367 results on 215 pages for 'devices'.

Page 31/215 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• Should I remove all unmanged switches from my network?

  - by IMAbev

  I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

  Read the article

• USB mouse disconnecting and reconnecting randomly and often

  - by Marc

  Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

  Read the article

• Unable to access intel fake RAID 1 array in Fedora 14 after reboot

  - by Sim

  Hello everyone, 1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays: 2x320GB RAID1 - used for operating systems md126 2x1TB RAID1 - used for data md125 I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only": [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active (auto-read-only) raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# and the partition in it was not available as device special file in /dev: [root@localhost ~]# ls -l /dev/md125* brw-rw---- 1 root disk 9, 125 Jan 6 15:50 /dev/md125 [root@localhost ~]# But the partition is there according to fdisk: [root@localhost ~]# fdisk -l /dev/md125 Disk /dev/md125: 1000.2 GB, 1000202043392 bytes 19 heads, 10 sectors/track, 10281682 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b238ea9 Device Boot Start End Blocks Id System /dev/md125p1 2048 1953519615 976758784 83 Linux [root@localhost ~]# I tried to "activate" the array in different ways (I'm not experienced with mdadm and the man page is gigantic so I was only browsing it looking for my answer) but it was impossible - the array would still stay in "auto read only" and the device special file for the partition it will not be in /dev. It was only after I recreated the partition via fdisk that it reappeared in /dev... until next reboot. So, my question is - How do I make the array automatically available after reboot? Here is some additional information: 1st I am able to see the UUID of the array in blkid: [root@localhost ~]# blkid /dev/sdc: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdd: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/md126p1: UUID="60C8D9A7C8D97C2A" TYPE="ntfs" /dev/md126p2: UUID="3d1b38a3-b469-4b7c-b016-8abfb26a5d7d" TYPE="ext4" /dev/md126p3: UUID="1Msqqr-AAF8-k0wi-VYnq-uWJU-y0OD-uIFBHL" TYPE="LVM2_member" /dev/mapper/vg00-rootlv: LABEL="_Fedora-14-x86_6" UUID="34cc1cf5-6845-4489-8303-7a90c7663f0a" TYPE="ext4" /dev/mapper/vg00-swaplv: UUID="4644d857-e13b-456c-ac03-6f26299c1046" TYPE="swap" /dev/mapper/vg00-homelv: UUID="82bd58b2-edab-4b4b-aec4-b79595ecd0e3" TYPE="ext4" /dev/mapper/vg00-varlv: UUID="1b001444-5fdd-41b6-a59a-9712ec6def33" TYPE="ext4" /dev/mapper/vg00-tmplv: UUID="bf7d2459-2b35-4a1c-9b81-d4c4f24a9842" TYPE="ext4" /dev/md125: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sda: TYPE="isw_raid_member" /dev/md125p1: UUID="420adfdd-6c4e-4552-93f0-2608938a4059" TYPE="ext4" [root@localhost ~]# Here is how /etc/mdadm.conf looks like: [root@localhost ~]# cat /etc/mdadm.conf # mdadm.conf written out by anaconda MAILADDR root AUTO +imsm +1.x -all ARRAY /dev/md1 UUID=89f60dee:e46a251f:7475814b:d4cc19a9 ARRAY /dev/md126 UUID=a8775c90:cee66376:5310fc13:63bcba5b ARRAY /dev/md125 UUID=b9a1149f:ae114fc8:a6000d77:354dc42a [root@localhost ~]# here is how /proc/mdstat looks like after I recreate the partition in the array so that it becomes available: [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# Detailed output regarding the array in subject: [root@localhost ~]# mdadm --detail /dev/md125 /dev/md125: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 976759808 (931.51 GiB 1000.20 GB) Used Dev Size : 976759940 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 2 Update Time : Fri Jan 7 00:38:00 2011 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 30ebc3c2:b6a64751:4758d05c:fa8ff782 Number Major Minor RaidDevice State 1 8 32 0 active sync /dev/sdc 0 8 48 1 active sync /dev/sdd [root@localhost ~]# and /etc/fstab, with /data commented (the filesystem that is on this array): # # /etc/fstab # Created by anaconda on Thu Jan 6 03:32:40 2011 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg00-rootlv / ext4 defaults 1 1 UUID=3d1b38a3-b469-4b7c-b016-8abfb26a5d7d /boot ext4 defaults 1 2 #UUID=420adfdd-6c4e-4552-93f0-2608938a4059 /data ext4 defaults 0 1 /dev/mapper/vg00-homelv /home ext4 defaults 1 2 /dev/mapper/vg00-tmplv /tmp ext4 defaults 1 2 /dev/mapper/vg00-varlv /var ext4 defaults 1 2 /dev/mapper/vg00-swaplv swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost ~]# Thanks in advance to everyone that even read this whole issue :-)

  Read the article

• Mount TMPFS instead of ro /dev

  - by schiggn

  I am working on a ARM-Based embedded system with a custom Debian Linux based on kernel 2.6.31. In the final system, the Root file system is stored as squashfs on flash. Now, the folder /dev is created by udev, but since there is no hot plugging functionality needed and booting time is critical, I wanted to delete udev and "hard code" the /dev folder (read here, page 5). because i still need to change parameters of the devices (with ioctl /sysfs) this does not work for me in this case. so i thought of mounting a tmpfs on /dev and change the parameters there. is this possible? and how to do best? my approach would be: delete /dev from RFS create tar containing basic devices mount tmpfs /dev untar tar-file into /dev change parameters Could this work? Do you see any problems? I found out, that you can mount on top of already mounted mount point, is it somehow possible just to take data with while mounting the new file system? if so that would be very convenient! Thanks Update: I just tried that out, but I'm stuck at a certain point. I packed all my devices into devices.tar, packed it into /usr of my squashfs and added the following lines to mountkernfs.sh, which is executed right after INIT. #mount /dev on tmpfs echo -n "Mounting /dev on tmpfs..." mount -o size=5M,mode=0755 -t tmpfs tmpfs /dev mknod -m 600 /dev/console c 5 1 mknod -m 600 /dev/null c 1 3 echo "done." echo -n "Populating /dev..." tar -xf /usr/devices.tar -C /dev echo "done." This works fine on the version over NFS, if I place printf's in the code, I can see it executing, if I comment out the extracting part, its complaining about missing devices. Booting OK mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. System Clock set to: Thu Sep 13 11:26:23 UTC 2012. INIT: Entering runlevel: 2 UBI: attaching mtd8 to ubi0 Commenting out the extraction of the tar mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Thu Sep 13 12:24:00 UTC 2012 ... (warning). INIT: Entering runlevel: 2 libubi: error!: cannot open "/dev/ubi_ctrl" So far so good. But if I pack the whole story into a squashfs and boot from there, it is acting strange. It's telling me while booting that it is unable to open an initial console and its throwing errors on mounting the UBIFS devices, but finally provides a login anyway. Over that my echo's are not executed. If I then log in, /dev is mounted as TMPFS as desired and all the devices reside inside. When I redo the "mount" command to mount the UBIFS partitions it is executed whitout problem and useable. From squashfs VFS: Mounted root (squashfs filesystem) readonly on device 31:15. Freeing init memory: 136K Warning: unable to open an initial console. mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 UBIFS error (pid 484): ubifs_get_sb: cannot open "ubi1_0", error -19 Additionally, a part of the rest of the bootscripts is still exexuted, but not all of them. Does anyone has a clue why? Other question, is 5MB enough/too much for /dev?

  Read the article

• Campus VLAN Segmentation - By OS?

  - by Moduspwnens

  We've been thinking through re-arranging our network and VLAN configuration. Here's the situation. We already have our servers, VoIP phones, and printers on their own VLANs, but our problem lies with end user devices. There are just too many to lump on the same VLAN without being hammered with broadcasts! Our current segmentation strategy has them split into VLANs like this: Student iPads Staff iPads Student Macbooks Staff Macbooks Gaming devices Staff (Other) Student (Other) *Note that our network has many more iPads and MacBooks than most. Since the primary reason we're splitting them is just to put them in smaller groups, this has been working for us (for the most part). However, this required our staff to maintain access control lists (MAC addresses) of all devices belonging in these groups. It also has the unfortunate side effect of illogically grouping broadcast traffic. For example, using this setup, students on opposite ends of campus using iPads will share broadcasts, but two devices belonging to the same user (in the same room) will likely be on completely separate VLANs. I feel like there must be a better way of doing this. I've done a lot of research and I'm having trouble finding instances of this kind of segmentation being recommended. The feedback on the most relevant SO question seems to point toward VLAN segmentation by building/physical location. I feel like that makes sense because logically, at least among miscellaneous end users, broadcasts will typically be intended for nearby devices. Are there other campuses/large-scale networks out there segmenting VLANs based on end-system OS? Is this a typical configuration? Would VLAN segmentation based on physical location (or some other criteria) be more effective? EDIT: I've been told that we will soon be able to dynamically determine device OS without maintaining access lists, although I'm not sure how much that affects the answers to the questions.

  Read the article

• Picture syncing on Multiple Macs, iPhones, and iPad together so each device can update them all

  - by cohortq

  Hello! One of the owners of my company has put me to task to sync his pictures between the following devices together. (2) iPhones (2) iMacs (1) Macbook Air (1) iPad Here is what is happening 1) He has a camera that can upload pictures into iPhoto in either (1) of his iMacs, or Macbook Air. 2) He has (2) different iPhones. And here are how they are paired up iPhone - iMac Home iPhone - Macbook Air 3) He has MobileMe syncing Calendar, Contacts, and Notes across all devices 4) Currently we are using MobileMe web galleries to sync all photos, by having ME create each album and upload them to the MobileMe web gallery. Not the problem is. He wants to just take pictures, and once he does that it syncs with all his devices, he'll even dock the iPad. Is there a better way to sync photos between all devices?

  Read the article

• Scanning for new disks attached using virtio?

  - by larsks

  I can successfully attach disks to a running KVM instance using virsh attach-disk... virsh attach-disk node-1 /dev/vg_lunsr/lun1 vdb Disk attached successfully ...but these new devices aren't seen by the guest without a reboot, which almost defeats the purpose of dynamic attachment. If these were SCSI devices I would use e.g. /sys/class/scsi_host/host0/scan to request the SCSI drivers to scan for new devices. Is there an equivalent capability for the virtio block driver?

  Read the article

• Add 802.11n to existing 802.11g environment

  - by Andrew Robinson

  I have a small home network that is currently running 802.11g. Two computers that are capable of 802.11n and two devices (a BlackBerry and a Skype phone) that are limited to 802.11g. I have a few neighbors running 802.11g but their signals are very weak. How big an impact will the two G devices have on N speeds? Will they pull the whole network back down to G? These two devices are hardly ever used where as the other N devices are heavily used. If I add an N router to the network (instead of replacing the G) and set my existing G router to use channel 1 with 20MHz bandwidth and then set the N router to use 6 & 11 for 40MHz will I eliminate the overlap and allow for full speed on both networks?

  Read the article

• Network monitoring solution

  - by Hellfrost

  Hello Serverfault ! I have a big distributed system I need to monitor. Background: My system is comprised of two servers, concentrating and controlling the system. Each server is connected to a set of devices (some custom kind of RF controllers, doesnt matter to my question), each device connects to a network switch, and eventually all devices talk to the servers, the protocol between the servers and the devices is UDP, usually the packets are very small, but there are really a LOT of packets. the network is also somewhat complex, and is deployed on a large area physically. i'll have 150-300 of these devices, each generating up to 100+ packets per second, and several network switches, perhaps on 2 different subnets. Question I'm looking for some solution that will allow me to monitor all this mess, how many packets are sent, where, how do they move through the network, bandwidth utilization, throughput, stuff like that. what would you recommend to achieve this? BTW Playing nice with windows is a requirement.

  Read the article

• No HDMI audio - Windows 8 - ASUS H81M-PLUS

  - by Paul Wright

  I have an issue with HDMI audio on Windows 8 using an ASUS H81M-PLUS motherboard (without an external GFX card). There are many forum posts advising you to go into playback devices and setting HDMI to be default - I have done this. To eliminate what works and what doesn't work: I have not been able to get sound from my HDTV using HDMI. I have used this HDMI cable with my PS3, so this cable should be fine. I am able to use the HDMI cable in extended mode, so that I have two monitors (including the TV), just no audio. This HDMI cable goes straight from the motherboard to the TV. Below I have included 'Device manager', and 'Playback Devices' (Sound). Device Manager Playback Devices, showing disabled and disconnected devices I am at a loss. I have uninstalled all drivers, and then rebooted and made windows look for the correct ones, made sure the HDMI device was default. Thanks, Paul

  Read the article

• Should USB controller drivers be updated?

  - by Coldblackice

  Should USB controller drivers be updated? In Windows 7, many of the core system devices/buses/controllers still use stock Microsoft drivers dating back to 2006 -- things such as USB controllers and the PCI bus (and subsequent devices in the tree). Should these be getting updated? I would think that surely there would have been improvements/fixes/updates to some or any of these drivers by now, now over 7 years old. Does Windows know "best" in this case, updating these respective drivers when it's needed, or should the user be keeping an eye out for drivers in this "vein" of devices (meaning integrated/core/non-pluggable system devices that are built into the motherboard)?

  Read the article

• Where is my problem? The P6X58D Premium Mobo, Windows 7, or other?

  - by Dylan Yaga

  I was having problems with my USB devices for an hour last night, and I am unable to determine the root cause of the problem. The two symptoms are: At seemingly random times (not consistently spaced by time or caused by any detectable event) my USB devices become "detached". Windows will play the USB disconnect sound and then the reconnect sound. The devices disconnected and then reconnected. My USB Keyboard will "stick" on one key for several seconds before processing any other keystroke made. The mouse also does not respond to clicks. I do not lose mouse movement or USB device connectivity. And after a moment of this several beeps will be emitted from the speakers. Hardware Specs: GFX Card: EVGA GeForce GTX 470 Superclocked 1280MB DDR5 PCIe Motherboard: ASUS P6X58D Premium Intel X58 Socket LGA1366 MB Processor: Intel Core i7-920 2.66Ghz 8M LGA1366 CPU Memory: Corsair Dominator 6144MB PC12800 DDR3 Storage: Hitachi 1TB Serial ATA HD 1600MHz 7200/32MB/SATA-3G Cooling: Corsair Hydro H50 CPU Liquid Cooler Case: Corsair Obsidian 800D Full Tower Case Power Supply: Corsair HX1000W 1000W Modular Power Supply Steps I have taken to narrow down the problem: Restarted the computer. - No change Changed USB port the Hub was connected to on the CPU. - No change Removed all devices from USB Hub and connected directly to CPU. - No change Used a different USB keyboard both in USB Hub and directly to CPU. - No change Disconnected and reconnected all cables. - No change Disassembled the Tower and determined if the USB headers were firmly connected. - No change Checked device manager for errors. Checked all USB devices. - Nothing flagged After an hour of frustration trying to narrow down the problem it appeared to disappear. But I am torn between it being a Mobo problem or an OS problem. Is there anything else I can do to narrow down the problem before a reformat and then eventually exchanging the Mobo?

  Read the article

• Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

  - by Quanano

  We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

  Read the article

• Unmanaged Network Switch vs Managed Network Switch

  - by David

  Currently I have an unmanaged POE switch connected to a Linksys router. I am thinking of upgrading my POE switch to a gigabit POE switch, the only problem is that the switch that I want to get is a managed switch. So here's my question: with a managed switch, can I still connect all of my devices to it and have the devices request IP addresses from the DHCP server within the Linksys router or will the devices request IPs from the managed switch since I believe the switch has its own DHCP server as well?

  Read the article

• Is WEP used in conjunction with a wireless access list adequate security?

  - by LeopardSkinPillBoxHat

  I use a Netgear wireless router, with various wireless devices connecting to it. One of my wireless devices doesn't support WPA2 security, so I had to downgrade the security on the router to WEP. We all know WEP is broken, so as an added measure I enabled a wireless access list on the router so that only devices with specified MAC addresses which are in my access list are permitted to connect to the router. I know it is possible to spoof a MAC address from a device for the purposes of accessing a secure network like this. But is it easy? Is using WEP and a wireless access list good enough to prevent most hacking attacks? Or should I do whatever I can to ensure all devices support WPA2 in the future?

  Read the article

• Konsole Read/Write Access to PTY Device

  - by Carmen

  When I run something like: $ konsole -e "sleep 30" I get this message Konsole is unable to open a PTY (pseudo teletype). It is likely that this is due to an incorrect configuration of the PTY devices. Konsole needs to have read/write access to the PTY devices. But if I try to run this: $ gnome-terminal -e "sleep 30" Then it is fine, and it does not throw any error. How can I change the read/write access of the Konsole to the PTY devices?

  Read the article

• Create and copy a Windows Mobile 5.0 operating system image

  - by user20119

  We have several dozen Windows Mobile 5.0 devices (Symbol MC7095 handhelds equipped with embedded Verizon WLAN, if that matters) that all need the same software and configuration. We connect all of these devices via a USB cradle to add software to them via Microsoft ActiveSync, and then do several configuration changes directly on the handhelds themselves, in the OS. That process takes 30 minutes or more, per device. Is there any way to set up one device and take a 'disk image' of the entire OS/software, such that things could then be copied (quickly/easily) to the other devices? Is such a thing possible, with Windows Mobile devices?

  Read the article

• Get OpenVPN clients names to resolve through dnsmasq

  - by Fake Name

  I have a PFSense box running as an OpenVPN server. There are several remote devices that connect through the VPN (as tap devices). The VPN stuff is working, I can access the remote hardware by looking up the IP assigned to each device on the PFSense router. What I'd like is to have it so I can resolve the remote hardware addresses via DNS while on the local network. Note that this is only local-network - remote-device (they're backup boxes). I don't need to have the remote devices resolve using the local DNS forwarding agent. I have the rest of the devices on the network that need to be accessible via DNS report their name during the DHCP process. However, the IP assignment for OpenVPN tap clients, while it is dynamic (which is why I need DNS), does not seem to use the local DHCP server. How can I have my openvpn server add information for it's clients to the dnsmask resolver? Is this setup even reasonable (I'm not familiar with openVPN at all)?

  Read the article

• Port-Forwarding in Virtual Box

  - by davidzaz

  I have Virtual Box setup with the following commands: vboxmanage setextradata myVm "VBoxInternal/Devices/pcnet/0/LUN#0/Config/transfer/HostPort" 50000 vboxmanage setextradata myVm `"VBoxInternal/Devices/pcnet/0/LUN#0/Config/transfer/GuestPort" 50000 vboxmanage setextradata myVm "VBoxInternal/Devices/pcnet/0/LUN#0/Config/transfer/Protocol" TCP On the host machine, the following command times out: telnet localhost 50000 What am I doing wrong? The above command does work on the guest machine.

  Read the article

• router with mixed-mode enabled - does it really cripple speeds for all?

  - by Mark C

  Hey all, If I have a router that has "mixed mode" enabled to allow b, g, and n devices, it is true that n devices will suffer in reduced bandwidth if there are any non-n devices connected? I found one article on the internet after a quick google search: http://www.wi-fiplanet.com/news/article.php/3335801 Can anyone corroborate or give their opinion on the matter? Thanks!

  Read the article

• Wireless Internet Connection Sharing in Ubuntu

  - by klutch2

  As the title states, I need to share a wireless connection with a laptop running Ubuntu as the AP. The setup will be as follows: Corporate WiFi <<== Laptop <<== Other Devices i.e. (iPad, iPhone) I want to be able to connect the "Other Devices" via WiFi to the laptop. I have thought of setting up an ad-hoc network by connecting to the Corporate WiFi and then setting up a new network and hoping the connection to both would stay, but that doesn't seem to work. If I set up the ad-hoc network by itself, I can see it from my "Other Devices". The reason I need this is because for some reason, my iPad and my iPhone will not connect to my corporate WiFi and I need to use them so I want to use my laptop to share the connection and act as an AP for my "Other Devices". My laptop is a Chrome CR-48 running Ubuntu and as some of you might know, it does not have an ethernet port, so having a wired connecting and then setting up a network is out of question. I want to connect to the Corporate WiFi and share that connection by having the laptop act as an AP for other devices.

  Read the article

• mdadm raid1 fails to resync

  - by JuanD

  Hello, I'm trying to solve this problem I'm having with an mdadm raid1. I have an ubuntu 9.04 server running on a software 2-drive raid1 with mdadm. Yesterday, one of the drives failed, and so I replaced it with a brand new drive of the same size. I removed the faulty drive, copied the partition from the remaining good drive to the new drive and then added it to the raid. It re-synced and the system worked fine, until the drive that hadn't failed, was also labeled failed. Now I had the raid running solely on the new drive. So I purchased another drive and repeated the procedure above. So now I had 2 brand new drives and the raid was syncing. However, after a few minutes I checked /proc/mdstat and the raid was no longer syncing. mdadm --detail /dev/md1 shows: (sdb is the first new drive, and sdc is the second new drive) root@dola:/home/jjaramillo# mdadm --detail /dev/md1 /dev/md1: Version : 00.90 Creation Time : Sat Dec 20 00:42:05 2008 Raid Level : raid1 Array Size : 974711680 (929.56 GiB 998.10 GB) Used Dev Size : 974711680 (929.56 GiB 998.10 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Jun 2 10:09:35 2010 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 UUID : bba497c6:5029ba0b:bfa4f887:c0dc8f3d Events : 0.5395594 Number Major Minor RaidDevice State 2 8 35 0 spare rebuilding /dev/sdc3 1 8 19 1 active sync /dev/sdb3 I've tried removing and re-adding the drive a few times, but the same thing happens. The raid fails to resync. I've looked at /var/log/messages, and found the following: Jun 2 07:57:36 dola kernel: [35708.917337] sd 5:0:0:0: [sdb] Unhandled sense code Jun 2 07:57:36 dola kernel: [35708.917339] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 2 07:57:36 dola kernel: [35708.917342] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor] Jun 2 07:57:36 dola kernel: [35708.917346] Descriptor sense data with sense descriptors (in hex): Jun 2 07:57:36 dola kernel: [35708.917348] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00 Jun 2 07:57:36 dola kernel: [35708.917357] 00 43 9e 47 Jun 2 07:57:36 dola kernel: [35708.917360] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed So it looks like there's some kind of error on sdb (the first new drive). My question is, what would be the best approach to get the raid up and running again? I've thought about dd'ing the /dev/md1 to a blank hard drive, then re-doing the raid from scratch and loading the data back, but there could be an easier solution.. Any help would be appreciated.

  Read the article

• Separate 2 networks with 1 Windows Server

  - by SamuGG

  The situation is: I have 1 router 192.168.1.1, 1 switch, 1 windows server and a basic LAN of devices accessing it. I need to split into 2 separate LANs with full Internet access each, but isolated from each other. Given that, the server is a Windows Server 2008 R2 with 2 NICs: NIC1: 192.168.1.2 NIC2: 192.168.2.2 The router has no dhcp configuration. Please, can anyone explain gracefully, step by step, what do I need to do? What would be the 2 NICs full configuration? What services do I need to install? I don't want devices on either network to see devices on the other network, they must be completely separate. I guess I'm missing the routing procedure step, but I have no idea how is that done. For example: tell the server that devices with gateway 192.168.2.2 must send traffic for internet to 192.168.1.1 router. Thanks in advance.

  Read the article

• Wireless connection silently dies randomly

  - by Force Flow

  I have two WAP4410N wireless access points powered using Power-Over-Ethernet. They are both connected to the same LAN and broadcasting the same SSID with a WPA2 password. One is using channel 1, while the other is using channel 11. There is coverage overlap where the signal from both access points hover around -75db to -85db while standing in the same physical location. DHCP is disabled, and is being provided by another network device. Every day or so, devices can connect and authenticate to the access points, but are not granted an IP address (and subsequently are unable access to the LAN or Internet). For devices that had already retrieved an IP address prior to the issue exhibiting itself, the devices simply stop communicating with LAN and Internet. However, I can still access each access point's web admin interface from the LAN. If I reboot both devices, the problem vanishes and devices are once again able to get an IP address and connect to the LAN and Internet. Are these symptoms of signal interference between the two WAPs or is this a completely different issue?

  Read the article

• Easily Plotting Multiple Data Series in Excel

  - by John

  I really need help figuring out how to speed up graphing multiple series on a graph. I have seperate devices that give monthly readings for several variables like pressure, temperature, and salinity. Each of these variables is going to be its own graph with devices being the series. My x-axis is going to be the dates that these values were taken. The problem is that it takes ages to do this for each spreadsheet since I have monthly dates from 1950 up to the present and I have about 50 devices in each spreadsheet. I also have graphs for calculated values that are in columns next to them. Each of these devices is going to become a data series in the graph. E.g. In one of my graphs I have all the pressures from the devices and each of the data series' names is the name of the device. I want a fast way to do this. Doing this manually is taking a very long time. Please help! Is there any easier way to do this? It is consistent and the dates all line up. I am just repeating the same clicks over and over again Thank you!

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >