Search Results

Search found 1344 results on 54 pages for 'it 07'.

Page 31/54 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• Apache /server-status/ gives a 404 not found

  - by kapshure

  I am trying to solve a problem where Apache stats aren't displaying correctly in Munin. I've ran through quite a bit of checks and tests regarding Munin setup, but I think my issue is related to Apache, but my skill set there is lacking. first, system info: monitored server CentOS 5.3 kernel 2.6.18-128.1.1.el5 Apache/2.2.3 "server-status" directive in httpd.conf (i've cross-compared this with another system that i did a successful parallel install of Munin on, correctly showing Apache stats, and the directive below is the same for both) ExtendedStatus On <Location /server-status> SetHandler server-status Order deny,allow Deny from all Allow from 127.0.0.1 </Location> ran lynx http://localhost/server-status got HTTP/1.1 404 taking a look at Apache access_log: 127.0.0.1 - - [13/Oct/2010:07:00:47 -0700] "GET /server-status HTTP/1.0" 404 11237 "-" "Lynx/2.8.5rel.1 libwww-FM/2.14 SSL-MM/1.4.1 OpenSSL/0.9.8e-fips-rhel5" mod_status is also loaded: % grep "mod_status" /etc/httpd/conf/httpd.conf LoadModule status_module modules/mod_status.so iptables is turned off also i did notice that the ownership status on httpd.conf on this system is root.root.. whereas the system that is displaying correctly is apache.www -- not certain that this matters?? its got to be permission issue, but i'm not certain where the permissions are messed up. any thoughts on why the test of server-status is giving me a 404?

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• Gerrit ssh key setup on windows server

  - by hotpotato

  I am attempting to configure google's 'Gerrit' code review web app on a Windows server 2008 virtual machine on our internal network. We are using Apache Tomcat (6.0.36) to host the web app and have deployed the gerrit.war to tomcats webapp folder, setup the context.xml, web.xml etc for the web app correctly i believe. However when i startup Tomcat using the $CATALINA_HOME/bin/startup.bat i get the following message in the tomcat logs: *Dec 07, 2012 1:03:54 PM org.apache.catalina.core.StandardContext listenerStart SEVERE: Exception sending context initialized event to listener instance of class com.google.gerrit.httpd.WebAppInitializer com.google.inject.CreationException: Guice creation errors:* 1) No SSH keys under C:\Gerrit\config\etc while locating com.google.gerrit.sshd.HostKeyProvider at com.google.gerrit.sshd.SshModule.configure(SshModule.java:90) I have created a is_rsa.pub SSH key and placed it in the specified directory to no avail. I have been googling this for about a week now and can't seem to find any information about the file or format it is expecting... documentation on setting gerrit up on windows seems hard to come by! Can anyone provide useful information about how to correctly configure a host SSH key in this context?

  Read the article

• repair partition table

  - by m.sr

  Hallo. I've just overwritten my partition table of my system's hard disk. i made a cfdisk on the wrong device (/dev/sda instead of /dev/sdd), deleted all partitions, made one new primary spanning over the whole device, set its type to 07 (NTFS) and hit write. So here i am with my system running. Until i reboot, i hope/guess nothing will change - meaning: all my data is accessible (I'm currently making a dd-backup of the whole device and plan to make a .tar.gz-backup of the most important data later). I also backed up /proc/partitions, /proc/diskstats (even though i guess this is more about throughput and stuff like this ...) and /sys/block/sda/sda?/{start,size}. Some further things i know: 4 primary partitions 1st partition: ~100Mb, ext3, /boot 2nd partition: ~100Mb, "Win7 Boot Partition", ntfs(?) 3rd partition: ~20...30GB, Win7, ntfs 4th partition: ~20...30GB, luks-encrypted device The luks- de crypted device is a LVM-PV The /, /home & swap-partitions are all LVs on the (VG on the) above noted PV So my questions: What is the simplest way to just write the kernels partition table to the disk? What is the simplest way to take the above mentioned (and perhaps other I don't know of ...) data and generate the partition table? Are there any problems to take care of regarding to luks and/or lvm? Is there any data I should backup before rebooting (meanig stuff from kernel [ /sys/..., /proc/...] and so on, which could help me regenerate the partition table)? Thanks a lot! P.S.: debian sid, Kernel 2.6.34-1-amd64 from debian-experimental, 80GB Intel SSD

  Read the article

• FastCGI and Apache 500 error intermittently

  - by benkorn1

  I have a FastCGI (mod_fastcgi)problem. It happens every once in a while, and does not casue a complete server meltdown, just 500 errors. Here are a couple things. First I am using APC so PHP is in control of it's own processes, not FastCGI. Also, I have the webroot set as: /var/www/html And the fcgi-bin inside: /var/www/html/fcgi-bin First off here is the apache error_log: [Fri Jan 07 10:22:39 2011] [error] [client 50.16.222.82] (4)Interrupted system call: FastCGI: comm with server "/var/www/html/fcgi-bin/php.fcgi" aborted: select() failed, referer: http://www.domain.com/ I also ran strace on the 'fcgi-pm' process. Here is a snip from the trace around the time it bombs out: 21725 gettimeofday({1294420603, 14360}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6503 38*", 16384) = 46 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 96595}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6154 23*C /var/www/html/fcgi-bin/php.fcgi - - 6483 28*", 16384) = 92 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 270744}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 5741 38*", 16384) = 46 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 311502}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6064 32*", 16384) = 46 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 365598}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6179 33*C /var/www/html/fcgi-bin/php.fcgi - - 5906 59*", 16384) = 92 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 454405}, NULL) = 0 I noticed that the 'select()' seems to stay the same regardless, however the read() changes its return from 46 to some other number while it is bombing out. Has anyone seen anything like this. Could this be some sort of file locking? Thanks, Ben

  Read the article

• Setting up Apache with multiple virtual host when using Plone 4.1

  - by Shaun Owens

  I have a Plone server running on CentOS, I have multiple instances of Plone running 4.0 and 4.1, I also have multiple sites. I am new to linux and haveing problems getting Apache to work with multiple virtuale hosts. The first host listed works just fine but the second host does not. I get the following error message when I start HTTPD: Starting httpd: [Mon Nov 07 14:38:31 2011] [warn] VirtualHost ordevel3.ucdavis.edu:80 overlaps with VirtualHost ordevel4.ucdavis.edu:80, the first has precedence, perhaps you need a NameVirtualHost directive. What am I missing to get the virtual hosts to work correctly? Below in my syntax in httpd.conf. <VirtualHost ordevel3.abc.edu:80> ServerAlias ordevel3.abc.edu ServerAdmin [email protected] ServerSignature On <IfModule mod_rewrite.c> RewriteEngine On # serving icons from apache 2 server RewriteRule ^/icons/ - [L] RewriteRule ^/(.*) \ http://localhost:8080/VirtualHostBase/http/%{SERVER_NAME}:80/itsdevel3/VirtualHostRoot/$1 [L,P] </IfModule> <IfModule mod_proxy.c> ProxyVia On # prevent the webserver from beeing used as proxy <LocationMatch "^[^/]"> Deny from all </LocationMatch> </IfModule> </VirtualHost> <VirtualHost ordevel4.abc.edu:80> ServerAlias ordevel4.abc.edu ServerAdmin [email protected] ServerSignature On <IfModule mod_rewrite.c> RewriteEngine On # serving icons from apache 2 server RewriteRule ^/icons/ - [L] RewriteRule ^/(.*) \ http://localhost:8180/VirtualHostBase/http/%{SERVER_NAME}:80/ITS/VirtualHostRoot/$1 [L,P] </IfModule> <IfModule mod_proxy.c> ProxyVia On # prevent the webserver from beeing used as proxy <LocationMatch "^[^/]"> Deny from all </LocationMatch> </IfModule> </VirtualHost>

  Read the article

• Problems with connecting Thunderbird client to dovecot installed on Ubuntu

  - by Michael Omer

  I am trying to connect a Thunderbird client to my dovecot server. The dovecot is installed on Ubuntu. I know that my server works (at least partially), since when I send a mail to a user in the server ([email protected]), I see the new file created in /home/feedback/Maildir/new. However, when I try to connect with my Thunderbird to the server, It recognizes the server, but informs me that my user/password is wrong (they are not wrong). The exact message is: Configuration could not be verified - is the username or password wrong? The server configuration it tries to connect to is: incoming - IMAP 143, outgoing - SMTP 587 The dovecot configuration file is located here: dovecot.conf My PAM configuration is: @include common-auth @include common-account @include common-session In the log, I see: May 23 06: 07: 20 misfortune dovecot: imap-login: Disconnected (no auth attempts): ? rip=77.126.236.118, lip=184.106.69.153 Dovecot -n gives me: Log_timestamp: %Y-%m-%d %H: %M: %S Protocols: pop3 pop3s imap imaps Ssl: no Login_dir: /var/run/dovecot/login Login_executable(default): /usr/lib/dovecot/imap-login Login_executable(imap): /usr/lib/dovecot/imap-login Login_executable(pop3): /usr/lib/dovecot/pop3-login Mail_privileged_group: mail Mail_location: maildir: ~/Maildir Mbox_write_locks: fcntl dotlock Mail_executable(default): /usr/lib/dovecot/imap Mail_executable(imap): /usr/lib/dovecot/imap Mail_executable(pop3): /usr/lib/dovecot/pop3 Mail_plugin_dir(default): /usr/lib/dovecot/modules/imap Mail_plugin_dir(imap): /usr/lib/dovecot/modules/imap Mail_plugin_dir(pop3): /usr/lib/dovecot/modules/pop3 Imap_client_workarounds(default): tb-extra-mailbox-sep Imap_client_workarounds(imap): tb-extra-mailbox-sep Imap_client_workarounds(pop3): Auth default: passdb: driver: pam userdb: driver: passwd

  Read the article

• Opening an existing process

  - by Grasper

  I am using Eclipse in Linux through a remote connection (xrdp). My internet got disconnected, so I got disconnected from the server while eclipse was running. Now I logged in again, and I do the "top" command I can see that eclipse is running and still under my user name. Is there some way I can bring that process back into my view (I do not want to kill it because I am in the middle of checking in a large swath of code)? It doesnt show up on the bottom panel after I logged in again. Here is the "top" output: /home/mclouti% top top - 08:32:31 up 43 days, 13:06, 29 users, load average: 0.56, 0.79, 0.82 Tasks: 447 total, 1 running, 446 sleeping, 0 stopped, 0 zombie Cpu(s): 6.0%us, 0.7%sy, 0.0%ni, 92.1%id, 1.1%wa, 0.1%hi, 0.1%si, 0.0%st Mem: 3107364k total, 2975852k used, 131512k free, 35756k buffers Swap: 2031608k total, 59860k used, 1971748k free, 817816k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 13415 mclouti 15 0 964m 333m 31m S 21.2 11.0 83:12.96 eclipse 16040 mclouti 15 0 2608 1348 888 R 0.7 0.0 0:00.12 top 31395 mclouti 15 0 29072 20m 8524 S 0.7 0.7 611:08.08 Xvnc 2583 root 20 0 898m 2652 1056 S 0.3 0.1 139:26.82 automount 28990 postgres 15 0 13564 868 304 S 0.3 0.0 26:33.36 postgres 28995 postgres 16 0 13808 1248 300 S 0.3 0.0 6:54.95 postgres 31440 mclouti 15 0 3072 1592 1036 S 0.3 0.1 6:01.54 gam_server 1 root 15 0 2072 524 496 S 0.0 0.0 0:03.00 init 2 root RT -5 0 0 0 S 0.0 0.0 0:04.53 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.04 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:01.72 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.07 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:04.33 migration/2 9 root 34 19 0 0 0 S 0.0 0.0 0:00.05 ksoftirqd/2

  Read the article

• High apache load but zero traffic

  - by Adie

  I have a problem with new server.. I use VPS Centos with 1GB of ram and I use wordpress CMS. The traffic <100 visitor/hour, but the apache have high load and make the server hang with zero free of ram and can't connect through ssh. I should reboot the vps to make it works here is the load on Apache looks like Tasks: 66 total, 1 running, 65 sleeping, 0 stopped, 0 zombie Cpu(s): 1.6%us, 12.3%sy, 0.0%ni, 48.1%id, 23.0%wa, 4.8%hi, 10.2%si, 0.0% Mem: 1018776k total, 116620k used, 902156k free, 1236k buffers Swap: 1048568k total, 1013052k used, 35516k free, 26628k cached 2949 apache 20 0 459m 42m 3732 D 3.0 4.2 0:09.23 httpd 2959 apache 20 0 460m 29m 3744 D 2.0 3.0 0:02.72 httpd 2968 apache 20 0 460m 26m 3808 D 2.0 2.6 0:02.27 httpd 2972 apache 20 0 460m 24m 3784 D 2.0 2.5 0:02.44 httpd 2986 apache 20 0 460m 29m 3784 R 2.0 2.9 0:02.40 httpd 2969 apache 20 0 458m 29m 3864 D 1.6 3.0 0:02.63 httpd 2974 apache 20 0 460m 25m 3820 D 1.6 2.6 0:02.43 httpd 2990 apache 20 0 460m 23m 3920 D 1.6 2.4 0:02.36 httpd 2994 apache 20 0 460m 31m 3756 D 1.6 3.2 0:02.62 httpd 2956 apache 20 0 460m 26m 3740 D 1.3 2.7 0:02.73 httpd 2957 apache 20 0 465m 22m 3644 D 1.3 2.3 0:02.80 httpd 2967 apache 20 0 458m 24m 3764 D 1.3 2.5 0:02.60 httpd 2970 apache 20 0 463m 25m 3764 D 1.3 2.6 0:03.07 httpd 2971 apache 20 0 451m 22m 3792 D 1.3 2.3 0:02.47 httpd 2973 apache 20 0 458m 25m 3768 D 1.3 2.6 0:02.52 httpd 2987 apache 20 0 465m 20m 3772 D 1.3 2.1 0:03.02 httpd But sometimes the server have uptime more than 5-10hrs but after that the problems start

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• Wireless disconnects at random after upgrade to Ubuntu 10.4

  - by Daniel Elessedil Kjeserud

  After upgrading my home server from Ubuntu 8.10 to 10.4 my wireless seemingly drops out, even though my IRC client keeps it's connection to the servers, so it looks like the machine just stops taking wireless requests. A ping will give a me this Request timeout for icmp_seq 27 ping: sendto: Host is down After a while the machine just starts responding again, without any interaction from me. When the machine comes back, this is what dmesg gives me [ 18.296288] wlan0: direct probe to AP 00:1b:63:22:a4:5f (try 1) [ 18.296350] wlan0: deauthenticating from 00:1b:63:22:a4:5f by local choice (reason=3) [ 18.296440] wlan0: direct probe to AP 00:1b:63:22:a4:5f (try 1) [ 18.298697] wlan0: direct probe responded [ 18.298706] wlan0: authenticate with AP 00:1b:63:22:a4:5f (try 1) [ 18.306836] wlan0: authenticated [ 18.306886] wlan0: associate with AP 00:1b:63:22:a4:5f (try 1) [ 18.309396] wlan0: RX AssocResp from 00:1b:63:22:a4:5f (capab=0x411 status=0 aid=2) [ 18.309402] wlan0: associated [ 18.310187] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 18.447742] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 18.447748] apm: overridden by ACPI. [ 19.163282] padlock: VIA PadLock not detected. [ 28.352022] wlan0: no IPv6 routers present kjes@brin:~$ lspci 02:07.0 Network controller: RaLink RT2561/RT61 rev B 802.11g It's on a wireless network with WPA2, the machine worked without any problems on the same wireless network since Ubuntu 8.10 was the most resent version, and there have been no changes to my network recently. Even though the server drops out, everything else on the network keeps working like normal.

  Read the article

• No audio in my ubuntu system

  - by hap497

  Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

  Read the article

• Can Xen be configured to dedicate only one port of a dual-port NIC to a domU?

  - by jamieb

  I'm using CentOS 5.4 on my dom0 with a stock Xen kernel. I'm attempting to use the pciback module to hide some of the Ethernet ports from the host and reserve them for a domU I intend to use for a firewall (process described here). However, when I launch the domU, I get the following error message: Using config file "/etc/xen/firewall". Error: pci: improper device assignment specified: pci: 0000:01:04.0 must be co-assigned to the same guest with 0000:01:06.0, but it is not owned by pciback. lspci gives me the following output: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) From the sound of the error message, it seems like I also need to dedicate eth0 (PCI ID 01:04.0) to the domU. Am I correct? If not, what am I doing wrong? Thanks!

  Read the article

• Using public interfaces on a server connected through a GRE tunnel

  - by Evan

  I'm pretty new to networking so please forgive any terminology mistakes. I have 2 servers connected with a GRE tunnel. Server1 (10.0.0.1) ---- Server2 (10.0.0.2) I want to be able to bind to the public IPs on Server2 using Server1. To do this, I setup virtual interfaces with Server2's public IPs on Server1 and then used routing rules on Server1 to route the packets through the GRE tunnel. On Server1: ip rule add from [Server2's first public IP] table gre ip rule add from [Server2's second public IP] table gre ip route add default via 10.0.0.2 dev gre1 table gre This works great and I can see the packets arriving via GRE on Server2. I can see the packet exiting the tunnel on Server2's gre1 device as shown: From Server1: ping -I [Server2's public ip] google.com tcpdump from Server2's GRE tunnel device: 12:07:17.029160 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) [Server2's public ip] > 74.125.225.38: ICMP echo request, id 6378, seq 50, length 64 This is exactly the packet I want. However, I'm not seeing it go out at all on eth0:0 (where Server2's public IP is bound to). I've tried to use routing rules to get packets coming from Server2's public IP (which would be coming out of dev gre1) to go through dev eth0 on the public default gateway and that doesn't work either. I'm at a loss, thank you to anyone who can help.

  Read the article

• Sony PMB causing failure to load Windows 7 Pro 64-bit normally or even Safe Mode

  - by Wesley

  After installing Sony's Picture Motion Browser on my desktop with Windows 7 Pro x64, it always goes to Startup Repair due to Windows 7 failing to start. This always happens after I try to install it. I've installed with all unnecessary programs closed and all disk drives and unnecessary usb ports empty. I don't exactly know what is causing the problem. Any ideas? My desktop is an HP m8530f. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01469325&tmp_task=prodinfoCategory&lc=en&dlc=en&cc=us&product=3740333&lang=en Only upgrades are an HD4350 and a 500W PSU. EDIT: Windows 7 cannot start now. I'm currently running diagnostic tests from the BIOS. EDIT: Here are the problem details. Problem Signature: Problem Event Name: StartupRepairOffline Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: 21201022 Problem Signature 05: AutoFailover Problem Signature 06: 8 Problem Signature 07: CorruptFile OS Version: 6.1.7600.2.0.0.256.1 Local ID: 1033 CONCLUSION: So, I think Sony PMB may have caused some sort of corruption in the system files. So if you have Windows 7 and plan on installing Sony PMB, find a Vista or XP machine to install on.

  Read the article

• Apache process consumes too much CPU

  - by Niro

  I have an ubuntu apache/php server running php doing appx 100 hits/sec and a PHP cron running in the background. I get occasionally high CPU load on one of the Apache processes which stays high regardless of traffic or cron activity. It seems to me that its stuck in some kind of loop or something. Below you will find the top and strace info. How can I find where the bad code is and what causes this? top - 14:45:24 up 3 days, 3:38, 1 user, load average: 5.10, 5.88, 5.85 Tasks: 163 total, 5 running, 158 sleeping, 0 stopped, 0 zombie Cpu(s): 47.8%us, 18.5%sy, 0.0%ni, 10.2%id, 0.0%wa, 0.0%hi, 1.8%si, 21.6%st Mem: 7885012k total, 3858484k used, 4026528k free, 177444k buffers Swap: 0k total, 0k used, 0k free, 1037868k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 10736 www-data 20 0 769m 559m 478m R 69 7.3 29:08.30 apache2 10844 www-data 20 0 824m 601m 492m S 17 7.8 4:37.90 apache2 1016 root 20 0 242m 25m 4628 S 6 0.3 162:07.93 scalarizr 9030 www-data 20 0 879m 619m 492m S 4 8.0 5:06.82 apache2 20216 www-data 20 0 747m 228m 170m S 4 3.0 0:01.94 apache2 10807 www-data 20 0 814m 584m 492m S 3 7.6 4:54.10 apache2 10455 www-data 20 0 831m 574m 492m S 3 7.5 4:32.65 apache2 10495 www-data 20 0 849m 592m 492m S 3 7.7 4:41.10 apache2 10884 www-data 20 0 840m 581m 492m S 3 7.6 4:25.06 apache2 ^CProcess 10736 detached % time seconds usecs/call calls errors syscall ------ ----------- ----------- --------- --------- ---------------- 74.55 0.148052 1 109755 gettimeofday 25.36 0.050370 0 164634 clock_gettime 0.09 0.000178 0 54878 poll ------ ----------- ----------- --------- --------- ---------------- 100.00 0.198600 329267 total root@ec2-67-202-54-36:~# ^C

  Read the article

• Tidy up old Windows Server Backup snapshots

  - by dty

  Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

  Read the article

• Why is my Drupal Registration email considered spam by gmail? (headers included)

  - by Jasper

  I just created a Drupal website on a uni.cc subdomain that is brand-new also (it has barely had the 24 hours to propagate). However, when signing up for a test account, the confirmation email was marked as spam by gmail. Below are the headers of the email, which may provide some clues. Delivered-To: *my_email*@gmail.com Received: by 10.213.20.84 with SMTP id e20cs81420ebb; Mon, 19 Apr 2010 08:07:33 -0700 (PDT) Received: by 10.115.65.19 with SMTP id s19mr3930949wak.203.1271689651710; Mon, 19 Apr 2010 08:07:31 -0700 (PDT) Return-Path: <[email protected]> Received: from bat.unixbsd.info (bat.unixbsd.info [208.87.242.79]) by mx.google.com with ESMTP id 12si14637941iwn.9.2010.04.19.08.07.31; Mon, 19 Apr 2010 08:07:31 -0700 (PDT) Received-SPF: pass (google.com: best guess record for domain of [email protected] designates 208.87.242.79 as permitted sender) client-ip=208.87.242.79; Authentication-Results: mx.google.com; spf=pass (google.com: best guess record for domain of [email protected] designates 208.87.242.79 as permitted sender) [email protected] Received: from nobody by bat.unixbsd.info with local (Exim 4.69) (envelope-from <[email protected]>) id 1O3sZP-0004mH-Ra for *my_email*@gmail.com; Mon, 19 Apr 2010 08:07:32 -0700 To: *my_email*@gmail.com Subject: Account details for Test at YuGiOh Rebirth MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8; format=flowed; delsp=yes Content-Transfer-Encoding: 8Bit X-Mailer: Drupal Errors-To: info -A T- yugiohrebirth.uni.cc From: info -A T- yugiohrebirth.uni.cc Message-Id: <[email protected]> Date: Mon, 19 Apr 2010 08:07:31 -0700 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - bat.unixbsd.info X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [99 500] / [47 12] X-AntiAbuse: Sender Address Domain - bat.unixbsd.info X-Source: X-Source-Args: /usr/local/apache/bin/httpd -DSSL X-Source-Dir: gmh.ugtech.net:/public_html/YuGiOhRebirth

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• why i cannot download jdk from oracle web site directly without AuthParam?

  - by hugemeow

  that is download with the following command, why it fails to download that file? wget http://download.oracle.com/otn-pub/java/jdk/6u35-b10/jdk-6u35-linux-i586.bin the following command works, but that AuthParam may not work after a while, why? wget http://download.oracle.com/otn-pub/java/jdk/6u35-b10/jdk-6u35-linux-i586.bin?AuthParam=1346955572_27e44512fe8ef5cb920c4c329e5f0fd8 how this AuthParam option is implemented? why i cannot download without this parameter? and why i can only get this parameter using explorer? is rewrite used in the oracle server when deal with wget request? why the same command not works after an hour, does the value of AuthParam expired? so how the server check whether the value of AuthParam is expired? wget http://download.oracle.com/otn-pub/java/jdk/6u35-b10/jdk-6u35-linux-i586.bin?AuthParam=1346955572_27e44512fe8ef5cb920c4c329e5f0fd8 --2012-09-07 03:51:01-- http://download.oracle.com/otn-pub/java/jdk/6u35-b10/jdk-6u35-linux-i586.bin?AuthParam=1346955572_27e44512fe8ef5cb920c4c329e5f0fd8 Resolving download.oracle.com... 23.67.251.50, 23.67.251.57 Connecting to download.oracle.com|23.67.251.50|:80... connected. HTTP request sent, awaiting response... 403 Forbidden 2012-09-07 03:51:01 ERROR 403: Forbidden. @KJ-SRS is that kind of CGI program which is used to judge if AuthParam is right? is that possible to download jdk package purely using wget command, and no need to get that AuthParam in explorer

  Read the article

• High CPU usage in my digitalocean droplet

  - by Ibrahim Azhar Armar

  I am experiencing high CPU usage here is the stats i got from server, the consumption after every restart in 15 minutes go upto 100%, what could go wrong? I have a wordpress copy installed on the server which does not have much traffic, here is the stats that i got from using top command in server. top - 11:46:02 up 12 min, 3 users, load average: 40.89, 16.03, 6.11 Tasks: 132 total, 41 running, 91 sleeping, 0 stopped, 0 zombie Cpu(s): 24.3%us, 61.5%sy, 0.0%ni, 0.0%id, 4.0%wa, 0.0%hi, 0.0%si, 10.2%st Mem: 2050896k total, 1988656k used, 62240k free, 284k buffers Swap: 0k total, 0k used, 0k free, 4712k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31 root 20 0 0 0 0 R 39 0.0 1:35.53 kswapd0 899 root 20 0 15988 172 0 S 14 0.0 0:05.00 irqbalance 418 syslog 20 0 243m 600 0 S 13 0.0 0:06.85 rsyslogd 944 mysql 20 0 1320m 53m 0 S 12 2.7 0:21.15 mysqld 2357 root 20 0 17344 532 164 R 11 0.0 0:14.27 top 960 root 20 0 246m 3816 0 S 3 0.2 0:08.18 php5-fpm 2431 www-data 20 0 344m 64m 908 R 2 3.2 0:04.23 apache2 2435 www-data 20 0 304m 63m 836 R 2 3.2 0:03.43 apache2 2413 www-data 20 0 349m 63m 920 R 2 3.2 0:07.51 apache2 2465 www-data 20 0 349m 64m 944 R 2 3.2 0:05.04 apache2 2518 www-data 20 0 307m 41m 1204 R 2 2.1 0:01.37 apache2 2406 www-data 20 0 346m 56m 1144 R 2 2.8 0:03.76 apache2 2456 www-data 20 0 345m 55m 1184 R 2 2.8 0:02.67 apache2 2373 www-data 20 0 351m 63m 784 R 2 3.2 0:11.09 apache2 2439 www-data 20 0 306m 35m 916 R 2 1.8 0:02.51 apache2 2450 www-data 20 0 345m 55m 1088 R 2 2.8 0:02.96 apache2 2486 www-data 20 0 299m 10m 876 R 2 0.5 0:01.19 apache2 2523 www-data 20 0 300m 27m 796 R 2 1.4 0:00.99 apache2

  Read the article

• Backup script to FTP with timed subfolders

  - by Frederik Nielsen

  I want to make a backup script, that makes a .tar.gz of a folder I define, say fx /root/tekkit/world This .tar.gz file should then be uploaded to a FTP server, named by the time it was uploaded, for example: 07-10-2012-13-00.tar.gz How should such backup script be written? I already figured out the .tar.gz part - just need the naming and the uploading to FTP. I know that FTP is not the most secure way to do it, but as it is non-sensitive data, and FTP is the only option I have, it will do. Edit: I ended up with this script: #!/bin/bash # have some path predefined for backup unless one is provided as first argument BACKUP_DIR="/root/tekkit/world/" TMP_DIR="/tmp/tekkitbackup/" FINISH_DIR="/tmp/tekkitfinished/" # construct name for our archive TIME=$(date +%d-%m-%Y-%H-%M) if [ $1 ]; then BACKUP_DIR="$1" fi echo "Backing up dir ... $BACKUP_DIR" mkdir $TMP_DIR cp -R $BACKUP_DIR $TMP_DIR cd $FINISH_DIR tar czvfp tekkit-$TIME.tar.gz -C $TMP_DIR . # create upload script for lftp cat <<EOF> lftp.upload.script open server user user password lcd $FINISH_DIR mput tekkit-$TIME.tar.gz exit EOF # start backup using lftp and script we created; if all went well print simple message and clean up lftp -f lftp.upload.script && ( echo Upload successfull ; rm lftp.upload.script )

  Read the article

• Content not being compressed even though I'm using zlib in php.ini

  - by Tola Odejayi

  I've edited my php.ini file so that it has these two entries: zlib.output_compression = On zlib.output_compression_level = 4 However, after restarting apache, when I request php pages, the headers returned in the response indicate that my server is still NOT serving compressed pages (here are selected headers as viewed using Chrome's Network feature): Cache-Control:no-cache, must-revalidate, max-age=0 Connection:Keep-Alive Content-Type:text/html; charset=UTF-8 Date:Mon, 17 Sep 2012 23:46:13 GMT Expires:Wed, 11 Jan 1984 05:00:00 GMT Last-Modified:Mon, 17 Sep 2012 23:46:13 GMT Pragma:no-cache Proxy-Connection:Keep-Alive Server:Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.17 Transfer-Encoding:chunked Via:1.1 XXX-PRXY-07 X-Powered-By:PHP/5.2.17 What might I be doing wrong? Is there any other setting that I need to change? EDIT Here is another set of headers returned to another computer: Cache-Control:no-cache, must-revalidate, max-age=0 Connection:close Content-Type:text/html; charset=UTF-8 Date:Thu, 20 Sep 2012 09:45:26 GMT Expires:Wed, 11 Jan 1984 05:00:00 GMT Last-Modified:Thu, 20 Sep 2012 09:45:26 GMT Pragma:no-cache Server:Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.17 Transfer-Encoding:chunked Vary:Cookie X-Powered-By:PHP/5.2.17

  Read the article

• Bacula virtual backup job doesn't run, no output?

  - by Zoredache

  I am trying to get Virtual Backups working, but when I try to run a virtual backup job, it appears to get created, but then never seems to actually run. I have a full, and a couple incremental backups. status director JobId Level Files Bytes Status Finished Name ==================================================================== 1283 Full 10,565 1.963 G OK 21-Dec-12 09:47 nms-Job 1284 Incr 314 129.6 M OK 21-Dec-12 09:49 nms-Job 1285 Incr 230 147.2 M OK 21-Dec-12 09:51 nms-Job 1288 Incr 525 138.8 M OK 21-Dec-12 11:25 nms-Job I attempt to start a job from bconsole like this. *run job=nms-Job level=VirtualFull Using Catalog "MySQL" Run Backup job JobName: nms-Job Level: VirtualFull Client: nms-FileDaemon FileSet: nms-FileSet Pool: nms-pool (From Job resource) Storage: File_d1 (From Pool resource) When: 2012-12-21 13:07:54 Priority: 10 OK to run? (yes/mod/no): Job queued. JobId=1291 Then my new job, just sits there, doing nothing. The JobStatus shows that the job was created, but it appears to never run? All the full, and incremental backups are terminating normally. *llist jobid=1291 JobId: 1,291 Job: nms-Job.2012-12-21_13.07.56_07 Name: nms-Job PurgedFiles: 0 Type: B Level: F ClientId: 4 Name: nms-FileDaemon JobStatus: C SchedTime: 2012-12-21 13:07:54 StartTime: 2012-12-21 13:07:56 EndTime: 0000-00-00 00:00:00 RealEndTime: 0000-00-00 00:00:00 JobTDate: 1,356,124,076 VolSessionId: 0 VolSessionTime: 0 JobFiles: 0 JobErrors: 0 JobMissingFiles: 0 PoolId: 19 PooLname: nms-pool PriorJobId: 0 FileSetId: 11 FileSet: nms-FileSet I am getting very frustrated, that this isn't working, mostly because it isn't giving me any error logs, or output at all. I submit the job, and as far as I can tell nothing happens. Is there some status, or debugging level that I can set to get a useful information about why this isn't working? What can I do to make this work? I was originally running Bacula 5.0.2 on Debian Squeeze, out of frustration, I upgraded to the 5.2.6 in the backports repository, hoping that a new version might give me better results.

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >