Search Results

Search found 4448 results on 178 pages for 'kernel'.

Page 31/178 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• Application stuck in TCP retransmit

  - by SandeepJ

  I am running Linux kernel 3.13 (Ubuntu 14.04) on two Virtual Machines each of which operates inside two different servers running ESXi 5.1. There is a zeromq client-server application running between the two VMs. After running for about 10-30 minutes, this application consistently hangs due to inability to retransmit a lost packet. When I run the same setup over Ubuntu 12.04 (Linux 3.11), the application never fails If you notice below, "ss" (socket statistics) shows 1 packet lost, sk_wmem_queued of 14110 (i.e. w14110) and a high rto (120000). State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 12350 192.168.2.122:41808 192.168.2.172:55550 timer:(on,16sec,10) uid:1000 ino:35042 sk:ffff880035bcb100 <- skmem:(r0,rb648720,t0,tb1164800,f2274,w14110,o0,bl0) ts sack cubic wscale:7,7 rto:120000 rtt:7.5/3 ato:40 mss:8948 cwnd:1 ssthresh:21 send 9.5Mbps unacked:1 retrans:1/10 lost:1 rcv_rtt:1476 rcv_space:37621 Since this has happened so consistently, I was able to capture the TCP log in wireshark. I found that the packet which is lost does get retransmitted and even acknowledged by the TCP in the other OS (the sequence number is seen in the ACK), but the sender doesn't seem to understand this ACK and continues retransmitting. MTU is 9000 on both virtual machines and througout the route. The packets being sent are large in size. As I said earlier, this does not happen on Ubuntu 12.04 (kernel 3.11). So I did a diff on the TCP config options (seen via "sysctl -a |grep tcp ") between 14.04 and 12.04 and found the following differences. I also noticed that net.ipv4.tcp_mtu_probing=0 in both configurations. Left side is 3.11, right side is 3.13 <<net.ipv4.tcp_abc = 0 <<net.ipv4.tcp_cookie_size = 0 <<net.ipv4.tcp_dma_copybreak = 4096 14c11 << net.ipv4.tcp_early_retrans = 2 --- >> net.ipv4.tcp_early_retrans = 3 17c14 << net.ipv4.tcp_fastopen = 0 >> net.ipv4.tcp_fastopen = 1 20d16 << net.ipv4.tcp_frto_response = 0 26,27c22 << net.ipv4.tcp_max_orphans = 16384 << net.ipv4.tcp_max_ssthresh = 0 >> net.ipv4.tcp_max_orphans = 4096 29,30c24,25 << net.ipv4.tcp_max_tw_buckets = 16384 << net.ipv4.tcp_mem = 94377 125837 188754 >> net.ipv4.tcp_max_tw_buckets = 4096 >> net.ipv4.tcp_mem = 23352 31138 46704 34a30 >> net.ipv4.tcp_notsent_lowat = -1 My question to the networking experts on this forum : Are there any other debugging tools or options I can install/enable to dig further into why this TCP retransmit failure is occurring so consistently ? Are there any configuration changes which might account for this weird behaviour.

  Read the article

• Ultra Low Latency Linux Distribution or Kernel

  - by Zanlor

  I'd like to know if there are any linux distributions that are focused on low latency networking. The area I'm working in is algorithmic trading, and extremely low latency comms between machines is a must. The current h/w we're using is 10g ethernet, we're looking into things like infiniband RDMA and Voltaire VMA I've googled around, and have only been able to find tidbtits of kernel patches, command line options and hardware suggestions. I'm looking for a complete solution, specially built kernel, kernel bypass features, essentially all the goodies rolled up into one package - does such a thing even exist? I ask as a lot of this stuff seems to be a black art, people keep secret what they know works etc.

  Read the article

• Ubuntu 14.04 VPS won't boot the latest kernel on XEN

  - by aztekk

  I have a XEN VPS and it's been running Ubuntu for some years now. AUtomatic security upgrades are on and I've manually upgraded it continously and also done releas-upgrades whenever there's been a new release. All has been working great! But now, after upgradeing to 14.04 LTS, the VPS won't boot the latest kernel (3.13.0-24) even though it's set to default. It always failback to 3.2.0-60 and for some reason the VPS seams very unresponsive, compared the before. The support wrote in a ticket something about compiling my own kernel, with pvops enabled, but I'm not sure how to do that, or why I should compile my own kernel. Doesn't Ubuntu support to be run on a XEN host?

  Read the article

• Linux kernel with grsec + Java / Apache Tomcat

  - by NoozNooz42

  I've got a Debian Linux 64 bit dedicated server. The kernel has the grsec patch applied. I'm mainly using this server to run Apache Tomcat (6.0.26, Java 6) and everything seems fine. The only issue, is that when I start Tomcat, I get a few of these: grsec: From xxx.xxx.xxx.xxx: Segmentation fault occurred at 00007fefe04e4000 in /home/t/jre1.6.0_20/bin/java[java:22403] uid/euid:1001/1001 gid/egid:1001/1001, parent /sbin/init[init:1] uid/euid:0/0 gid/egid:0/0 grsec: more alerts, logging disabled for 10 seconds Then no error logs anymore. Everything is fine. The kernel is: Linux 2.6.32.2-xxxx-grs-ipv4-64 #1 SMP Tue Dec 29 14:41:12 UTC 2009 x86_64 GNU/Linux And the webapp works fine. So there are segmentation fault when Tomcat starts, but everything seems to works fine. Is this concerning? Should I move to a non-grsec kernel?

  Read the article

• Booting Windows7 kernel from an initrd/wim image file

  - by Ivo

  I'm wondering if it's possibile to have Win7 kernel and relative drivers (especially storage drivers) to boot from an initrd-like image file (maybe .wim?) and later then mount the windows root partition and complete the load of the full OS? I'll try to explain why: I'm running an emulated environment with NO REAL BIOS, and I'm passingthrough a raid storage controller. I want windows to boot from this controller array, but of course the BCD manager cannot access disks in the array until kernel and relative controller storage drivers are loaded. To be clear I get the classical winload.exe missing error. I need a similar solution to what Linux does, loading the kernel and his drivers, and later then mount the root partition and complete the boot. Any ideas or advices?

  Read the article

• Randomly displayed flashing lines, no response to all shortcuts, just power off. [syslog included]

  - by B. Roland

  Hello! I have an old machine, and I want to use for that to learn employees how to use Ubuntu, and to be easyer to switch from Windows. I've been installed 10.04, and updated, but this strange stuff is happend. Graphical installion failed, same strange thing. With alternate workd. Sometimes, when I boot up, a boot message displayed: Keyboard failure..., often diplayed after reboot, and after shutdown, when I haven't plugged off from AC. I replaced the keyboard yet, same failure... If I powered off, and plugged off from AC, no keyboard problems displayed in boot time. Details Configuration: Dell OptiPlex GX60 - in original cover, no changes. 256 MB DDR 166 MHz Intel® Celeron® Processor 2.40 GHz Dell 0C3207 Base Board I know, that is not enough, but I have three other Nec compuers, with nearly similar config, and they works well with 9.10, 10.04, 10.10. Live CDs I've been tried with 10.04 and 10.10, but the problem is displayed too. With 9.10 no strange things displayed, but it froze, during a simple apt-get install. Syslog An error loop is logged here, but I paste the whole startup and error lines. The flashing lines are displayed sometimes immediately after login, but sometimes after 10 minutes, but once occured, that nothing happend. Strange thing is displayed immediately after login: here. An other boot, after some minutes, strange lines, and loop in log appeard: here. The loop should be that: Jan 23 00:20:08 machine_name kernel: [ 46.782212] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 23 00:20:08 machine_name kernel: [ 47.100033] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 23 00:20:08 machine_name kernel: [ 47.100045] render error detected, EIR: 0x00000000 Jan 23 00:20:08 machine_name kernel: [ 47.101487] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 16 at 9) Jan 23 00:20:11 machine_name kernel: [ 49.152020] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 23 00:20:11 machine_name gdm-simple-slave[1245]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Jan 23 00:20:11 machine_name acpid: client 1239[0:0] has disconnected Jan 23 00:20:11 machine_name acpid: client connected from 1247[0:0] Jan 23 00:20:11 machine_name acpid: 1 client rule loaded UPDATE Added syslog things: before errors, error loop, the complete shutdown(after the big updates): Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully called chroot. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully dropped privileges. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully limited resources. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Watchdog thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Canary thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully made thread 1337 of process 1337 (n/a) owned by '1001' high priority at nice level -11. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Supervising 1 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1345 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 2 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1349 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 3 threads of 1 processes of 1 users. Jan 28 20:40:37 machine_name pulseaudio[1337]: ratelimit.c: 2 events suppressed Jan 28 20:41:33 machine_name AptDaemon: INFO: Initializing daemon Jan 28 20:41:44 machine_name kernel: [ 167.691563] lo: Disabled Privacy Extensions Jan 28 20:47:33 machine_name AptDaemon: INFO: Quiting due to inactivity Jan 28 20:47:33 machine_name AptDaemon: INFO: Shutdown was requested Jan 28 20:59:50 machine_name kernel: [ 1253.840513] lo: Disabled Privacy Extensions Jan 28 21:17:02 machine_name CRON[1874]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 21:17:38 machine_name kernel: [ 2321.553239] lo: Disabled Privacy Extensions Jan 28 22:07:44 machine_name kernel: [ 5327.840254] lo: Disabled Privacy Extensions Jan 28 22:17:02 machine_name CRON[2665]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 22:57:03 machine_name kernel: [ 8286.641472] lo: Disabled Privacy Extensions Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 23:07:42 machine_name kernel: [ 8925.272030] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:07:42 machine_name kernel: [ 8925.272048] render error detected, EIR: 0x00000000 Jan 28 23:07:42 machine_name kernel: [ 8925.272093] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171453 at 171452) Jan 28 23:07:45 machine_name kernel: [ 8928.868041] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:10 machine_name acpid: client 925[0:0] has disconnected Jan 28 23:08:10 machine_name acpid: client connected from 8127[0:0] Jan 28 23:08:10 machine_name acpid: 1 client rule loaded Jan 28 23:08:11 machine_name kernel: [ 8955.046248] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:12 machine_name kernel: [ 8955.364016] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:12 machine_name kernel: [ 8955.364027] render error detected, EIR: 0x00000000 Jan 28 23:08:12 machine_name kernel: [ 8955.364407] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171457 at 171452) Jan 28 23:08:14 machine_name kernel: [ 8957.472025] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:14 machine_name acpid: client 8127[0:0] has disconnected Jan 28 23:08:14 machine_name acpid: client connected from 8141[0:0] Jan 28 23:08:14 machine_name acpid: 1 client rule loaded Jan 28 23:08:15 machine_name kernel: [ 8958.671722] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:15 machine_name kernel: [ 8958.988015] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:15 machine_name kernel: [ 8958.988026] render error detected, EIR: 0x00000000 Jan 28 23:08:15 machine_name kernel: [ 8958.989400] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171459 at 171452) Jan 28 23:08:16 machine_name init: tty4 main process (848) killed by TERM signal Jan 28 23:08:16 machine_name init: tty5 main process (856) killed by TERM signal Jan 28 23:08:16 machine_name NetworkManager: nm_signal_handler(): Caught signal 15, shutting down normally. Jan 28 23:08:16 machine_name init: tty2 main process (874) killed by TERM signal Jan 28 23:08:16 machine_name init: tty3 main process (875) killed by TERM signal Jan 28 23:08:16 machine_name init: tty6 main process (877) killed by TERM signal Jan 28 23:08:16 machine_name init: cron main process (890) killed by TERM signal Jan 28 23:08:16 machine_name init: tty1 main process (1146) killed by TERM signal Jan 28 23:08:16 machine_name avahi-daemon[644]: Got SIGTERM, quitting. Jan 28 23:08:16 machine_name avahi-daemon[644]: Leaving mDNS multicast group on interface eth0.IPv4 with address 10.238.11.134. Jan 28 23:08:16 machine_name acpid: exiting Jan 28 23:08:16 machine_name init: avahi-daemon main process (644) terminated with status 255 Jan 28 23:08:17 machine_name kernel: Kernel logging (proc) stopped. Jan 28 23:09:00 machine_name kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 28 23:09:00 machine_name rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="516" x-info="http://www.rsyslog.com"] (re)start Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's groupid changed to 103 Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's userid changed to 101 Jan 28 23:09:00 machine_name rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] When I hit the On/Off button, the system shuts down normally. May be it a hardware problem, but I don't know... Can you say something useful to solve my problem?

  Read the article

• xt_TCPMSS: bad length messages

  - by Matic

  I'm getting loads of messages like: Jun 23 10:24:20 awakening kernel: [ 1691.596823] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663362] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663495] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663588] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663671] xt_TCPMSS: bad length (1440 bytes) Jun 23 10:24:26 awakening kernel: [ 1697.062914] xt_TCPMSS: bad length (474 bytes) Jun 23 10:24:26 awakening kernel: [ 1697.305525] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:27 awakening kernel: [ 1698.946633] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:36 awakening kernel: [ 1707.481198] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:37 awakening kernel: [ 1708.723526] xt_TCPMSS: bad length (805 bytes) Jun 23 10:24:38 awakening kernel: [ 1709.599461] xt_TCPMSS: bad length (805 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.211052] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.260588] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.976058] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:43 awakening kernel: [ 1714.225209] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:43 awakening kernel: [ 1714.914961] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:55 awakening kernel: [ 1726.192696] xt_TCPMSS: bad length (1480 bytes) Jun 23 10:24:55 awakening kernel: [ 1726.192825] xt_TCPMSS: bad length (1480 bytes) In my dmesg/syslog. This linux machine is among other things used as an internet gateway. Connection is over PPPoE. I have the following line in my iptables script: $IPT -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu # PPPoE fix The frequency of this messages increased 10x when I upgraded from Debian lenny with 2.6.27 to squeeze with 2.6.32 few days ago. Why am I seeing this messages and how can I fix them?

  Read the article

• Wireless disconnect randomly with wpa_supplicant reason=2

  - by renenglish

  I installed ubuntu-server 12.04 on my PC , and I use an usb wireless card to join the network. It works ok when I boot up my PC , but the wireless disconnects after a while. I pkill wpa_supplicant and reload the driver rtl8192cu , then it works a again. Then it disconnect again after about a random minutes. Here is the syslog: 22384 May 29 21:49:27 homecenter kernel: [ 6450.459313] wlan1: authenticated 22385 May 29 21:49:27 homecenter kernel: [ 6450.459535] wlan1: associate with f4:ec:38:45:62:74 (try 1) 22386 May 29 21:49:27 homecenter kernel: [ 6450.469080] wlan1: RX AssocResp from f4:ec:38:45:62:74 (capab=0 x431 status=0 aid=3) 22387 May 29 21:49:27 homecenter kernel: [ 6450.469085] wlan1: associated 22388 May 29 21:49:27 homecenter wpa_supplicant[2342]: Associated with f4:ec:38:45:62:74 22389 May 29 21:49:27 homecenter kernel: [ 6450.481933] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 22390 May 29 21:49:27 homecenter wpa_supplicant[2342]: WPA: Key negotiation completed with f4:ec:38:45:62:7 4 [PTK=CCMP GTK=CCMP] 22391 May 29 21:49:27 homecenter wpa_supplicant[2342]: CTRL-EVENT-CONNECTED - Connection to f4:ec:38:45:62: 74 completed (auth) [id=0 id_str=] 22392 May 29 21:49:38 homecenter kernel: [ 6461.472014] wlan1: no IPv6 routers present 22393 May 29 21:49:38 homecenter ntpdate[2263]: step time server 91.189.94.4 offset 0.012758 sec 22394 May 29 21:49:51 homecenter ntpdate[2404]: step time server 91.189.94.4 offset -0.001190 sec 22395 May 29 21:54:38 homecenter kernel: [ 6762.052030] wlan1: deauthenticated from f4:ec:38:45:62:74 (Reas on: 2) 22396 May 29 21:54:38 homecenter wpa_supplicant[2342]: CTRL-EVENT-DISCONNECTED bssid=f4:ec:38:45:62:74 reas on=2 22397 May 29 21:54:38 homecenter kernel: [ 6762.064744] cfg80211: All devices are disconnected, going to re store regulatory settings 22398 May 29 21:54:38 homecenter kernel: [ 6762.064752] cfg80211: Restoring regulatory settings 22399 May 29 21:54:38 homecenter kernel: [ 6762.064757] cfg80211: Calling CRDA to update world regulatory d omain 22400 May 29 21:54:38 homecenter kernel: [ 6762.069938] cfg80211: Ignoring regulatory request Set by core s ince the driver uses its own custom regulatory domain 22401 May 29 21:54:38 homecenter kernel: [ 6762.069943] cfg80211: World regulatory domain updated: 22402 May 29 21:54:38 homecenter kernel: [ 6762.069945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 22403 May 29 21:54:38 homecenter kernel: [ 6762.069949] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22404 May 29 21:54:38 homecenter kernel: [ 6762.069952] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22405 May 29 21:54:38 homecenter kernel: [ 6762.069956] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22406 May 29 21:54:38 homecenter kernel: [ 6762.069959] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22407 May 29 21:54:38 homecenter kernel: [ 6762.069962] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KH z), (300 mBi, 2000 mBm)

  Read the article

• xt_TCPMSS: bad length messages

  - by Matic

  Hey! I'm getting loads of messages like: Jun 23 10:24:20 awakening kernel: [ 1691.596823] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663362] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663495] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663588] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663671] xt_TCPMSS: bad length (1440 bytes) Jun 23 10:24:26 awakening kernel: [ 1697.062914] xt_TCPMSS: bad length (474 bytes) Jun 23 10:24:26 awakening kernel: [ 1697.305525] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:27 awakening kernel: [ 1698.946633] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:36 awakening kernel: [ 1707.481198] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:37 awakening kernel: [ 1708.723526] xt_TCPMSS: bad length (805 bytes) Jun 23 10:24:38 awakening kernel: [ 1709.599461] xt_TCPMSS: bad length (805 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.211052] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.260588] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.976058] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:43 awakening kernel: [ 1714.225209] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:43 awakening kernel: [ 1714.914961] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:55 awakening kernel: [ 1726.192696] xt_TCPMSS: bad length (1480 bytes) Jun 23 10:24:55 awakening kernel: [ 1726.192825] xt_TCPMSS: bad length (1480 bytes) In my dmesg/syslog. This linux machine is among other things used as an internet gateway. Connection is over PPPoE. I have the following line in my iptables script: $IPT -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu # PPPoE fix The frequency of this messages increased 10x when I upgraded from Debian lenny with 2.6.27 to squeeze with 2.6.32 few days ago. Why am I seeing this messages and how can I fix them?

  Read the article

• Wireless cuts out on Toshiba Satellite S7208

  - by alecRN

  I recently got a Toshiba Satellite L875-S7208 with Windows 7 preinstalled. I installed Ubuntu 12.04 LTS dual boot to the same Windows partition. However, usually 15 minutes or less after booting, the wifi connection dies. Here's some hopefully relevant information: lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: i2c-i801 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8211] Kernel driver in use: rtl8192ce Kernel modules: rtl8192ce 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Subsystem: Toshiba America Info Systems Device [1179:fb37] Kernel driver in use: r8169 Kernel modules: r8169 lsmod Module Size Used by snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224066 1 joydev 17693 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 arc4 12529 2 snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 87692 0 serio_raw 13211 0 rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device sparse_keymap 13890 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev mac_hid 13253 0 mei 41616 0 wmi 19256 0 soundcore 15091 1 snd i915 472941 3 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 cfg80211 205544 2 rtlwifi,mac80211 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 ums_realtek 18248 0 uas 18180 0 usb_storage 49198 1 ums_realtek dmesg | grep firmware [ 15.692951] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 16.240881] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 452.419288] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail. [ 458.572211] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 465.440640] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 472.337617] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 479.175471] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 485.978582] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 492.764893] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 499.579348] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 506.386934] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 513.209545] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 519.991365] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 526.778375] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 533.629695] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 540.426004] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 547.238125] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 554.024434] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 560.854794] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 567.678160] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 574.494666] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 581.336653] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 588.157710] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 595.221122] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 602.047429] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 608.829534] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 615.639079] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 622.454991] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 629.273231] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 636.056613] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 642.858096] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 649.640753] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 657.184094] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 664.008018] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 670.838639] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 677.675418] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 684.507255] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 691.310994] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 698.095325] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 704.914509] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 711.725178] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin uname -r 3.2.0-29-generic ifconfig eth0 Link encap:Ethernet HWaddr 4c:72:b9:59:6c:61 inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe59:6c61/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:0 overruns:0 frame:0 TX packets:2762 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3671147 (3.6 MB) TX bytes:335133 (335.1 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:515 errors:0 dropped:0 overruns:0 frame:0 TX packets:515 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:83153 (83.1 KB) TX bytes:83153 (83.1 KB) wlan0 Link encap:Ethernet HWaddr 74:e5:43:32:47:95 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32958 (32.9 KB) TX bytes:10431 (10.4 KB)

  Read the article

• CUDA small kernel 2d convolution - how to do it

  - by paulAl

  I've been experimenting with CUDA kernels for days to perform a fast 2D convolution between a 500x500 image (but I could also vary the dimensions) and a very small 2D kernel (a laplacian 2d kernel, so it's a 3x3 kernel.. too small to take a huge advantage with all the cuda threads). I created a CPU classic implementation (two for loops, as easy as you would think) and then I started creating CUDA kernels. After a few disappointing attempts to perform a faster convolution I ended up with this code: http://www.evl.uic.edu/sjames/cs525/final.html (see the Shared Memory section), it basically lets a 16x16 threads block load all the convolution data he needs in the shared memory and then performs the convolution. Nothing, the CPU is still a lot faster. I didn't try the FFT approach because the CUDA SDK states that it is efficient with large kernel sizes. Whether or not you read everything I wrote, my question is: how can I perform a fast 2D convolution between a relatively large image and a very small kernel (3x3) with CUDA?

  Read the article

• VirtualBox error VERR_SUPDRV_COMPONENT_NOT_FOUND

  - by ant2009

  I am using Fedora 12, with kernel stv-fedora 2.6.31.12-174.2.22.fc12.i686 I have install VirtualBox OSE v3.1.4-1.fc12. When I start VirtualBox I get the following error: Failed to start the virtual machine WinXP32. Failed to open/create the internal network 'HostInterfaceNetworking-eth0' (VERR_SUPDRV_COMPONENT_NOT_FOUND). One of the kernel modules was not successfully loaded. Make sure that no kernel modules from an older version of VirtualBox exist. Then try to recompile and reload the kernel modules by executing '/etc/init.d/vboxdrv setup' as root (VERR_SUPDRV_COMPONENT_NOT_FOUND). However, if I run /etc/init.d/vboxdrv setup I get this error: -bash: /etc/init.d/vboxdrv: No such file or directory How do I get rid of the error and run VirtualBox?

  Read the article

• Disabling kextcache on 10.5.8 and 10.6.3

  - by Jeff Kelley

  We use Radmind to manage our Mac OS X loadsets and, as such, often run into difficulty when new OS releases come out due to, among other things, updated kernel extensions. The workflow in the past (OS revisions <= 10.4) was to delete the kernel extension cache, update the extensions, and then reboot. That worked just fine, as the system would re-create missing caches on boot. In Leopard, you need to delete the caches after replacing the kernel extensions with their new versions, as the system will automatically start creating them when you replace them; the only way to ensure that you don't have invalid extensions cached is to delete the cache before rebooting. I'm looking for a way to prevent the kernel extensions cache from being re-created until the next reboot. If you modify the contents of /System/Library/Extensions/, kextcache will start up automatically. I've looked through /System/Library/LaunchDaemons/ and other places, but I can't find whatever it is that's starting kextcache. Any ideas?

  Read the article

• Packet drop measured by ethtool, tcpdump and ifconfig

  - by Rayne

  Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

  Read the article

• OS Development. Only Few Particular Questions

  - by Total Anime Immersion

  I am new to this site as a member but have consulted its answers quite a lot of times. Besides my questions regarding OS Development hasn't been answered in any forum. In OS Dev. we make a bootloader. The org point is 7C00H. Why so? Why not 0000h? What are the last two signatures in the bootloader used for? People on every forum have answered that it is important for the system to recognize it as a bootable media. But I want a specific answer. What do each of those signatures do. I have the basic concept of a kernel. Point is.. it relates to different files required in a system. It sort of binds up everything that is individually developed. Now the thing is that that I have floating ideas in my mind regarding different aspects like keyboard, mouse, etc.. how do I put them all together? Which should I start with first? If possible please provide a step by step procedure of the startups of the kernel. Suppose I have developed my language entirely in C and Assembly. Now questions is will exe files work on my system.. if it doesn't then I have to create my own files and publish them. Which is a bad idea.. next step would be for me to go for a compiler for a language which I have designed myself. Now the point is.. How do I implement the compiler into my OS? After all this my final question is that.. How do you go about multitasking and multithreading? and I don't want to use int 21h as its dos specific.. how do I go about making files, renaming them, etc. and all assembly books teach 16 but programming.. how do i go about doing 32 bit or 64 bit with the knowledge I have.. if the basics and instructions are the same.. I don't mind.. but how do i go about otherwise? Don't tell me to give up the idea because I WON'T. And don't tell me it's too complex because I have a sharp knowledge of working of a system, C, Java, Assembly, C++ and python, C#, visual basic.. and not just basics but full fledged api developments.. but I really want to go deep into the systems part.. so I want professional help.. And I have gone through many OS project files but I want help particularly from this site as there are people with knowledge depth who can guide me the right way. And please don't suggest any books above 20$ and they should be available on flipkart as amazon charges massively for shipping and I prefer free shipping from flipkart.

  Read the article

• Writing a "Hello World" Device Driver for kernel 2.6 using Eclipse

  - by Isaac

  Goal I am trying to write a simple device driver on Ubuntu. I want to do this using Eclipse (or a better IDE that is suitable for driver programming). Here is the code: #include <linux/module.h> static int __init hello_world( void ) { printk( "hello world!\n" ); return 0; } static void __exit goodbye_world( void ) { printk( "goodbye world!\n" ); } module_init( hello_world ); module_exit( goodbye_world ); My effort After some research, I decided to use Eclipse CTD for developing the driver (while I am still not sure if it supports multi-threading debugging tools). So I: Installed Ubuntu 11.04 desktop x86 on a VMWare virtual machine, Installed eclipse-cdt and linux-headers-2.6.38-8 using Synaptic Package Manager, Created a C Project named TestDriver1 and copy-pasted above code to it, Changed the default build command, make, to the following customized build command: make -C /lib/modules/2.6.38-8-generic/build M=/home/isaac/workspace/TestDriver1 The problem I get an error when I try to build this project using eclipse. Here is the log for the build: **** Build of configuration Debug for project TestDriver1 **** make -C /lib/modules/2.6.38-8-generic/build M=/home/isaac/workspace/TestDriver1 all make: Entering directory '/usr/src/linux-headers-2.6.38-8-generic' make: *** No rule to make target vmlinux', needed byall'. Stop. make: Leaving directory '/usr/src/linux-headers-2.6.38-8-generic' Interestingly, I get no error when I use shell instead of eclipse to build this project. To use shell, I just create a Makefile containing obj-m += TestDriver1.o and use the above make command to build. So, something must be wrong with the eclipse Makefile. Maybe it is looking for the vmlinux architecture (?) or something while current architecture is x86. Maybe it's because of VMWare? As I understood, eclipse creates the makefiles automatically and modifying it manually would cause errors in the future OR make managing makefile difficult. So, how can I compile this project on eclipse?

  Read the article

• how to concatenate two strings in shell script in 3.13.0-34-generic kernel

  - by saikrishna

  I want to concatenate two strings for the shell file im getting error when i have created the shell file in following manner could you please suggest how to get it set export APP_HOME="/home/sfptladmin/ArchivalDaemon" export JAVA_HOME="/usr/lib/jvm/java-7-oracle/jre" export LIBPATH="/home/sfptladmin/ArchivalDaemon/lib" export CPATH=$APP_HOME/conf export CPATH=$CPATH:$LIBPATH/commons-beanutils-core-1.7.0.jar export CPATH=$CPATH:$LIBPATH/commons-collections-3.2.jar export CPATH=$CPATH:$LIBPATH/commons-io-1.4.jar export CPATH=$CPATH:$LIBPATH/commons-lang.jar export CPATH=$CPATH:$LIBPATH/commons-net.jar export CPATH=$CPATH:$LIBPATH/dataloader-27.0.1-uber.jar export CPATH=$CPATH:$LIBPATH/dom4j-1.6.1.jar export CPATH=$CPATH:$LIBPATH/log4j-1.2.15.jar export CPATH=$CPATH:$LIBPATH/opencsv2.3.jar export CPATH=$CPATH:$LIBPATH/poi-3.7.jar export CPATH=$CPATH:$LIBPATH/poi-ooxml-3.7.jar export CPATH=$CPATH:$LIBPATH/poi-ooxml-schemas-3.7.jar export CPATH=$CPATH:$LIBPATH/wsc-23-min.jar export CPATH=$CPATH:$LIBPATH/xmlbeans-2.5.0.jar export CPATH=$CPATH:$LIBPATH/archival-daemon-main.jar export CPATH=$CPATH:$LIBPATH/sbmclasspath.jar export CPATH=$CPATH java -Xms256m -Xmx512m -classpath $CPATH "-Dfile.encoding=UTF-8" com.genpact.proflow.daemon.archival.manager.ArchivalManager echo $CPATH

  Read the article

• APT wedged by kernel version mismatch

  - by Leopd

  Apt is seemingly unable to do anything useful for me, repeatedly giving messages of this form: dpkg: dependency problems prevent configuration of linux-server: linux-server depends on linux-image-server (= 3.2.0.37.44); however: Version of linux-image-server on system is 3.2.0.37.45. linux-server depends on linux-headers-server (= 3.2.0.37.44); however: Version of linux-headers-server on system is 3.2.0.37.45. dpkg: error processing linux-server (--configure): dependency problems - leaving unconfigured This is basically the same problem as I cannot install any package (linux-image-server, linux-server dependencies errors) which got closed Duplicate to an answer that is totally useless for this situation. None of the advice in that very generic answer about dependencies helps. Explicitly: sudo apt-get clean sudo apt-get autoclean sudo apt-get update all have no not effect. While sudo apt-get -f install sudo dpkg --configure -a sudo apt-get -u dist-upgrade sudo apt-get -o Debug::pkgProblemResolver=yes dist-upgrade all give some form of the error message above.

  Read the article

• Linux Kernel 2.6.34 Adds Scalable Ceph Filesystem

  This week, Linus Torvalds announced the availability of the latest version of the open source operating system.

  Read the article

• Linux Kernel 2.6.34 Adds Scalable Ceph Filesystem

  This week, Linus Torvalds announced the availability of the latest version of the open source operating system.

  Read the article

• All my sites are 403 but the server is running. Errors on startup

  - by Craig

  We gave access to a contractor to install a firewall and somehow while he was doing it he fracked something up. Everything went off-line about 24 hours ago and we are effectively out of business until I solve this and the person who messed up the thing is not returning calls. I found a few errors. First, I'm not a server guy - I can look at log files and normally everything runs fine. All 'services' are running according to 1and1 server monitoring and mail is being delivered just fine. The whole thing was off-line until I (probably stupidly) updated the kernel from 6.2 to 6.3 this morning and I got everything back except the http access. All the domains (~200 of them) are returning a 403 error and nothing is recorded in the access log. On every restart I see this error in the messages log file: init: Failed to spawn ttyS0 main process: unable to execute: No such file or directory and a little later these: kernel: WARNING: at kernel/sched.c:5914 thread_return+0x232/0x79d() (Not tainted) kernel: Hardware name: X9SCL/X9SCM kernel: Modules linked in: xt_iprange iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ext4 jbd2 serio_raw i2c_i801 i2c_core sg iTCO_wdt iTCO_vendor_support e1000e ext3 jbd mbcache raid1 sd_mod crc_t10dif ahci dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] kernel: Pid: 367, comm: md3_raid1 Not tainted 2.6.32-220.2.1.el6.x86_64 #1 kernel: Call Trace: kernel: [<ffffffff81069997>] ? warn_slowpath_common+0x87/0xc0 kernel: [<ffffffff810699ea>] ? warn_slowpath_null+0x1a/0x20 kernel: [<ffffffff814eccc5>] ? thread_return+0x232/0x79d kernel: [<ffffffff8126a4d9>] ? cpumask_next_and+0x29/0x50 kernel: [<ffffffff813e9c05>] ? md_super_wait+0x55/0x90 kernel: [<ffffffff81090a10>] ? autoremove_wake_function+0x0/0x40 kernel: [<ffffffff813ebf46>] ? md_update_sb+0x206/0x3f0 kernel: [<ffffffff813ee922>] ? md_check_recovery+0x3f2/0x6d0 kernel: [<ffffffffa005b129>] ? raid1d+0x49/0x1050 [raid1] kernel: [<ffffffff814ed985>] ? schedule_timeout+0x215/0x2e0 kernel: [<ffffffff814ef447>] ? _spin_unlock_irqrestore+0x17/0x20 kernel: [<ffffffff813eb336>] ? md_thread+0x116/0x150 kernel: [<ffffffff81090a10>] ? autoremove_wake_function+0x0/0x40 kernel: [<ffffffff813eb220>] ? md_thread+0x0/0x150 kernel: [<ffffffff810906a6>] ? kthread+0x96/0xa0 kernel: [<ffffffff8100c14a>] ? child_rip+0xa/0x20 kernel: [<ffffffff81090610>] ? kthread+0x0/0xa0 kernel: [<ffffffff8100c140>] ? child_rip+0x0/0x20 And something is wrong with the Named/BIND resulting in the same error for all domains: zone DOMAINEXAMPLE.com/IN: loading from master file DOMAINEXAMPLE.com failed: file not found zone DOMAINEXAMPLE.com/IN: not loaded due to errors. _default/DOMAINEXAMPLE.com/IN: file not found I'm pretty sure this is not enough information to solve the problem, but I'm willing to engage someone who can work this out for me. Any help would be greatly appreciated.

  Read the article

• Download specific kernels for distros

  - by ant2009

  Hello, I am running CentOS 5.3. I am wondering where I can download the latest kernel for this distribution. I went to www.centos.org but could see any kernel download only the complete distribution is available to download. I just want the kernel. Kernels on the www.kernels.org are the vanilla kernels. I am wondering where to download for the specific distro? Many thanks for any advice,

  Read the article

• end_request: I/O error, dev sda, sector xxxxxxxxx

  - by muruga

  I have a IBM server. This server contains 3 hard disk with RAID 5. It was working fine earlier. Unfortunately this machine got the following error message. After that I have rebooted the systems. After that I am getting the following error message in kern.log and demsg kernel: [65896.678870] end_request: I/O error, dev sda, sector 17430271 kernel: [69263.783957] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK : [69263.783957] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] kernel: [69263.783957] sd 0:0:0:0: [sda] Add. Sense: Internal target failure Whether it is kernel problem or hard disk problem or Raid problem

  Read the article

• Cannot boot: FGLRX 8.780 + Kernel 2.6.35-25

  - by pluc

  The situation before this all happened is pretty standard. I have a HP Pavillion dv5 laptop with an ATI Mobility Radeon 4200 series. It always worked fine with Ubuntu for as long as I can remember. However, at one point, something happened and truly made a majestic mess of things. It might've been extra repos I enabled with Ubuntu Tweak - I do not know. But something made it so that my system would not boot any longer. And when I say "won't boot", this is what I mean: - Durning a normal bootup, any entries (except Windows) selected with GRUB (or BURG, not even sure which one I'm using anymore) will spawn the Ubuntu loading screen - then try to start X (or GDM) 5 times. The screen goes to dark, black and back to the Ubuntu loading screen. Then it just stays there until I spawn another TTY. I have no idea what is happening or why. There are no errors in my logs, and I'm truly at a loss here. I've linked three files: Xorg.0.log, the output of dmesg and the GDM log: Xorg.0.log: http://ubuntu.pastebin.com/tpVKc2tc dmesg: ubuntu.pastebin.com/Nd5aYj45 gdm's :0.log: couldn't post due to lack of points :( Let me know if any of you more knowledgeable folks can restore some sanity in my life. Any help is greatly apreciated.

  Read the article

• What is shrink_slab, and why is it showing up in /var/log/messages?

  - by Steve Kehlet

  I'm investigating some application issues on a Linux system and noticed this around the time of the most recent problem, but not close enough to be definitively related: Jun 7 17:51:49 localhost kernel: shrink_slab: nr=-155456000 Jun 7 17:51:49 localhost kernel: shrink_slab: nr=-157859400 Jun 7 17:51:49 localhost kernel: shrink_slab: nr=-157833400 Jun 8 06:20:23 localhost kernel: shrink_slab: nr=-284172800 What is this? Googling isn't helping, I get that it's something with VM, but why is it suddenly showing up in /var/log/messages? Edit: I take it it's showing this because the number of pages it could free ("nr") is negative. Which is presumably a bad thing. I found patches for newer kernels that display a more useful message to this effect. Still not sure what this means though, or what I need to do about it.

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >