Search Results

Search found 10052 results on 403 pages for 'mutation testing'.

Page 310/403 | < Previous Page | 306 307 308 309 310 311 312 313 314 315 316 317  | Next Page >

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• Whats the best cloud backup solution for a small scale server environment?

  - by nbv4

  I have a server that runs a postgres database that contains about 200MB of data. Currently I have a cron job setup on my home computer which: ssh's into my server runs a remote script which makes a backup of the database scp's that dump over to my local hard drive for storage. Each dump is 20MiB. does this every six hours (one months of backups is roughly 2GiB) The problem with this setup is that if my local machine goes down for whatever reason, no backups will be made. Also, I can't have the cron run from the server, because I can't have it scp'd to my local machine from my server (firewalls and all that crap). My local machine is running Ubuntu 10.04, and my server is Ubuntu 9.10 server edition. I looked into Ubuntu One, but currently it's gui-only. I also looked into dropbox, but it's a pain in the ass to get setup in linux without gui support. Amazon S3 looks good but it's not free (yet dirt cheap). Is there any other alternative that I should look into? I'd prefer something where I can just have my script dump the database into a directory, and have the backup service 'watch' that folder and sync accordingly. I can maybe also have my local machine sync to the cloud backup so I have even more redundancy, plus easy access to my backups for use in testing. Edit: My server is a VPS, so what solution I end up using has to be 100% software based.

  Read the article

• Windows based development environment: HyperV, VMWare, or VirtualBox on development machine?

  - by bleepzter

  I am a software engineer with a little bit of an informal "support" functionality... I am trying to figure out what is the best possible approach to employing virtualization technologies into our development process. Since the code we develop is server-centric, testing it often requires a VM with specific software requirements. I used to use VM Ware player (free version) to run my VM's until both of my laptops started exhibiting issues with corrupted windows 7 services and dying hard drives. All leads pointed to VMWare, which by the way seems to be a solid product if you pay for the Workstation edition ($300). On a side note, I have always been a fan of the Windows Server product line. I think it makes for one of the best development environments out there - it is highly scalable, highly reliable, and very efficient. So to be fair I replaced the drives of the laptops and installed Windows Server 2008R2, VS2010 Ultimate SP1, SQL Server 2008R2, TFS Server 2010 and all other tools and API's needed do do my work properly. So now I am stuck with a bunch of VMWare VMs. I don't want to repeat of what happened before, and I certainly don't want to bog down my machine with an inefficient hypervisor or services that are not needed. Futhermore the VMDK hard-disk format used by VMWare is not compatible with the VHD format of Hyper V. It is my understanding that converting from one format to the other can only happen by Microsoft System Center Virtual Machine which I have downloaded from MSDN and ready to install. I guess the question at this point is: Does SCVM run as another service in Windows? Is it a memory hog? What is a better virtualization technology - Hyper-V or Virtual Box in terms of efficiency ease of use and most importantly - memory footprint? (Keep in mind the development environment already has a ton of services running such as TFS Server, SQL Server, IIS, etc...) How would you advise to proceed at this point so that the VMs are still used in the test process? Thanks Martin

  Read the article

• How can I make grub2 boot into Windows 7?

  - by Grzenio

  I had Windows 7 installed on my system, then I installed Debian testing with grub2 as its boot manager. Initially I couldn't see windows entry in grub at all, so I ran: aptitude install os-prober kcpuload update-grub Now I can see the entry, but when I select it I get only Win7 system restore, instead of the the real thing. Any ides how to make it work? EDIT: I tried the suggested approach to add a new file to /etc/grub.d, which generated an entry in grub.cfg, but it does not appear in the grub menu on boot :( I have this: grzes:/home/ga# cat /etc/grub.d/11_Windows #! /bin/sh -e echo Adding Windows >&2 cat << EOF menuentry “Windows 7? { set root=(hd0,2) chainloader +1 } And I have the following grub.cfg file: grzes:/home/ga# cat /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } insmod ext2 set root=(hd0,3) search --no-floppy --fs-uuid --set 6ce3ff31-0ef7-41df-a6f5-b6b886db3a94 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi set locale_dir=/boot/grub/locale set lang=en insmod gettext set timeout=5 ### END /etc/grub.d/00_header ###

  Read the article

• Windows 7 logon script net use fails

  - by Bryan

  Our network PCs currently consists of Windows XP Professional on a mixed 2008/2003 domain, with exception to one machine, which is a new Windows 7 PC we have bought for testing before we deploy the operating system. But we have discovered a problem with our logon script which automatically maps network drives for our users. The logon scripts are done via User GPOs, but the script itself is just a .cmd file using net use. The permissions are perfectly fine, as the same user can log on to a Windows XP machine and get their drives mapped without problem, but this one drive mapping constantly fails. This is repeatable using the net use command, and fails every time - it actually prompts the user for a username and password when executed interactively, yet if we enter \\server\share from a run dialog, the contents of the network share appear and are accessible without any further authentication. The Windows 7 PC (just like the XP systems) are domain members and the account being used is a domain account, which does have access to the share (as stated, it works fine on XP). I fail to understand what is happening here, as other shares on the server get mapped on the Windows 7 system. More info: The effective permissions of the share in question only grant the user 'list' permission on the root directory, the share permissions are 'everyone,full control'. I've created a new share with the same permissions just to test if it was down to the 'list' permissions on the root directory, but the Windows 7 machine maps this one fine.

  Read the article

• I have a perl script that is supposed to run indefinitely. It's being killed... how do I determine who or what kills it?

  - by John O

  I run the perl script in screen (I can log in and check debug output). Nothing in the logic of the script should be capable of killing it quite this dead. I'm one of only two people with access to the server, and the other guy swears that it isn't him (and we both have quite a bit of money riding on it continuing to run without a hitch). I have no reason to believe that some hacker has managed to get a shell or anything like that. I have very little reason to suspect the admins of the host operation (bandwidth/cpu-wise, this script is pretty lightweight). Screen continues to run, but at the end of the output of the perl script I see "Killed" and it has dropped back to a prompt. How do I go about testing what is whacking the damn thing? I've checked crontab, nothing in there that would kill random/non-random processes. Nothing in any of the log files gives any hint. It will run from 2 to 8 hours, it would seem (and on my mac at home, it will run well over 24 hours without a problem). The server is running Ubuntu version something or other, I can look that up if it matters.

  Read the article

• Exchange emails not delivering for one user

  - by Cylindric

  We have an Exchange infrastructure going through a migration from 2003 SP2 (call it ExOld) to 2010 (ExNew). All users are now on the new server, but mail is still being directed to ExOld until testing is complete. ExNew sends emails directly to the internet. For one particular user, emails don't seem to be being reliably delivered, but the odd thing is that it's not all emails. I can see external emails in his inbox. If I send an internal email it works fine. If I send an email from Gmail to him it doesn't get through. If I telnet from outside to ExOld I can send an email to him. If I telnet from outside to ExNew I can send an email to him. This is a transcript that results in a successful send: 220 ExOldName Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Mon, 22 Oct 2012 10:55:26 +0100 EHLO test.com 500 5.3.3 Unrecognized command EHLO test.com 250-ExOldFQDN Hello [MyTestExternalIp] 250-TURN 250-SIZE 250-ETRN 250-PIPELINING 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-CHUNKING 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XEXCH50 250 OK MAIL FROM:[email protected] 250 2.1.0 [email protected] OK RCPT TO:[email protected] notify=success,failure 250 2.1.5 [email protected] DATA 354 Start mail input; end with . Subject:Test 1056 Test 10:56 . 250 2.6.0 Queued mail for delivery quit 221 2.0.0 ExOldFQDN Service closing transmission channel Emails go through Symantec Cloud, but their "Track and Trace" shows the messages going through, with a "delivered ok" log entry. 2012-10-22 09:19:56 Connection from: 209.85.212.171 (mail-wi0-f171.google.com) 2012-10-22 09:19:56 Sending server HELO string:mail-wi0-f171.google.com 2012-10-22 09:19:56 Message id:CAE5-_4hzGpY2kXFbzxu7gzEUSj5BAvi+BB5q1Gjb6UUOXOWT3g@mail.gmail.com 2012-10-22 09:19:56 Message reference: 135089759500000177171130001194006 2012-10-22 09:19:56 Sender: [email protected] 2012-10-22 09:19:56 Recipient: [email protected] 2012-10-22 09:20:26 SMTP Status: OK 2012-10-22 09:19:56 Delivery attempt #1 (final) 2012-10-22 09:19:56 Recipient server: ExOldIP (ExOldIP) 2012-10-22 09:19:56 Response: 250 2.6.0 Queued mail for delivery I'm not sure where to look on the old (or new) server for information as to where the mails are ending up.

  Read the article

• Maintenance window and recovery for a large database

  - by NYSystemsAnalyst

  One of our teams is developing a database that will be somewhat large (~500GB) and grow from there (I know 500 Gigs may seem small to many of you, but it will be one of the larger databases in our shop). One of the issues they are grappling with is backing up and restoring the database. Basically, the database will have several "data" tables and one table used for storing images / documents. We need to accomplish the following: Be able to quickly backup and restore only the data tables (sans images) to our test server for debugging and testing purposes. In the event of a catastrophic database failure, restore the data tables only to get most of the application up and running ASAP. Then, restore the images table when possible. Backup the database within the allotted nightly time window (a few hours). My questions are: Is it possible to accomplish the first two goals while still having the images stored in the same database? If so, would we use filegroups, filestream, or something else? How do other shops backup their databases in a reasonable time window while maintaining high availability? Do you replicate to a second server and backup from there?

  Read the article

• Monitoring instantaneous network throughput at one second intervals?

  - by Shaddi

  For a testing setup I have, I need to monitor the throughput through a "router"* at regular intervals of around 5 seconds or less (sub-second intervals would be very nice, but not required). Ideally, I would be able to generate a file which contained both the number of bytes and packets seen during each interval. I will eventually be generating a time-series of throughput from this data. On a previous setup using an older version of FreeBSD, there was a tool called "bpfmon" which gave me this information. However, I need to do this under a modern version of Linux (namely, Ubuntu 11.04). I have looked at both iptraf and iftop, but these do not appear to provide the resolution I need, nor do they seem to easily allow scraping the data I need. I understand iptables statistics may be able to give me what I'm after, but the examples I've seen of this seem to rely on repeatedly reading and resetting traffic counters, which seems like it could give inaccurate as read/reset is not an atomic operation. I already capture a tcpdump trace of the traffic I'm interested in on the link I want to monitor, so I am open to approaches which simply parse that. I feel like this must be a common problem though, so I am hoping there will be a standard "best practice" tool for accomplishing this. *I say "router" in quotes because I am really talking about a machine with two bridged NICs through which all the traffic I'm interested in passes.

  Read the article

• VMWare Server modifying files related to paused VMs, is this expected?

  - by David Spillett

  While refreshing the backup of a VM used for testing, I experienced the following warning from tar: tar: /VMsR0/cli_noddyco_test/VM2K8_32_web.vmem: file changed as we read it The VMs in question were paused at the time. My first though was that I'd mixed up the machines and was trying to backup something that was still actively running. To be sure I unpaused and properly shut down the VM, and the vmem files that tar reported changing vanished as I would expect. Is it normal for VMWare Server to touch or alter files for paused VMs like this, or is there likely something amiss with our setup? If this is expected behaviour, is just touching the vmem file (and so altering the last modification date without actually changing content)? If it is normal for files relating to paused VMs to be updated I shall have to revise our backup procedures to make sure the VMs are fully shut down fully rather than just pausing them (this isn't a problem, but it seems strange and I'd prefer to understand what VMWare is doing and why instead of just dismissing it as "one of those things" and working around it). For further detail: the host in question is VMWare Server version 2.0.2 running on 64-bit Debian/Lenny, and that VM did not have a snapshots at the time. We have backed up paused VMs this way in the past with no such warnings from tar.

  Read the article

• Drowning in documents - recommend doc management solutions?

  - by Martin Day

  I've been researching document management lately. I want to organise my docs at home and also at the office. Finding affordable solutions one can actually test drive is quite hard. Some that I've downloaded just don't seem to work (testing on brand new Vista PC). I've seen some software on Amazon like Paperport but not really sure what they're like. For home I'd like something to organise files, full text search, good scanner integration, nice interface etc. But for the office it seems harder. I need something that does proper workflow and keeps versions. It will have an audit trail. Documents can be approved, checked in/out etc. I know a few clients who would like something similar. It would be great just to import thousands of documents from a shared drive and get them indexed with dupes killed. I'd like to be super clear about how/where the documents are being stored so that maintenance and backups are clear. My Google/twitter searches lead back to the same tired and vague webpages pushing what look like expensive and custom made solutions. Some might be very good I suppose but it's darn hard to tell. I don't mind a hosted package but all in all I don't think something like Google Docs, as good as it is now, will work. There are too many quirks and missing features (as compared to Office). Being able to work directly with the common Office file formats is important. I've noted a similar sounding question asked here back in August but it didn't seem to turn up too many solutions that I could easily and quickly apply. Also there could have been some changes since then so I feel it's worth asking.

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• Possible to have different SSLCACertificateFiles under different Location in Apache (client side ssl certs)

  - by Mikko Ohtamaa

  I am setting up Apache to do smartcard authentication. The smartcard login is based on client-side SSL certificates handled by an OS driver. I have currently just one smartcard provider, but in the future there are potentially several of them. I am not sure how Apache 2.2. handles client-side certifications per Location. I did some quick testing and it somehow seemed that only the last SSLCACertificateFile directive would have been effective and this doesn't sound right. Is it possible to have different SSLCACertificateFile per Location in Apache (2.2, 2.4) as described below or is SSL protocol somehow limiting that you cannot have more than one SSLCACertificateFile per IP? Example potential config below how I wish to handle several SSLCACertificateFile on the same server to allow users to log in with different smartcard provides. <VirtualHost 127.0.0.1:443> # Real men use mod_proxy DocumentRoot "/nowhere" ServerName local-apache ServerAdmin [email protected] SSLEngine on SSLOptions +StdEnvVars +ExportCertData # Server-side HTTPS configuration SSLCertificateFile /etc/apache2/certificate-test/server.crt SSLCertificateKeyFile /etc/apache2/certificate-test/server.key # Normal SSL site traffic does not require verify client SSLVerifyClient none SSLVerifyDepth 999 # Provider 1 <Location /@@smartcard-login> SSLVerifyClient require SSLCACertificateFile /etc/apache2/certificate-test/ca.crt # Apache does not natively pass forward headers # created by SSLOptions +StdEnvVars, # so we pass them forward to Python using RequestHeader # from mod_headers RequestHeader set X-Client-DN %{SSL_CLIENT_S_DN}e RequestHeader set X-Client-Verify %{SSL_CLIENT_VERIFY}e </Location> # Provider 2 <Location /@@smartcard-login-provider-2> # For real SSLVerifyClient require SSLCACertificateFile /etc/apache2/certificate-test/provider2.crt # Apache does not natively pass forward headers # created by SSLOptions +StdEnvVars, # so we pass them forward to Python using RequestHeader # from mod_headers RequestHeader set X-Client-DN %{SSL_CLIENT_S_DN}e RequestHeader set X-Client-Verify %{SSL_CLIENT_VERIFY}e </Location> # Connect to Plone ZEO client1 running on fg ProxyPass / http://localhost:8080/VirtualHostBase/https/local-apache:443/folder_sits/sitsngta/VirtualHostRoot/ ProxyPassReverse / http://localhost:8080/VirtualHostBase/https/local-apache:443/folder_sits/sitsngta/VirtualHostRoot/ </VirtualHost>

  Read the article

• VMWare vSphere 5: 4 pNICs for iSCSI vs. 2 pNICs

  - by gravyface

  New SAN for me, never used before: it's an IBM DS3512, dual controller with a quad 1GbE NIC per controller that a client bought and needs help setting up. Hosts (x2) have 8 pNICs and while I usually reserve 2 pNICs for iSCSI per host (and 2 for VM, 2 for management, 2 for vMotion, staggered across adapters), these extra ports on the SAN have me wondering if storage I/O would be significantly improved with 2 additional NICs per host, or if the limitations of the vmkernel/initiator would prevent the additional multipaths from ever being realized. I'm not seeing alot of 4 pNIC iSCSI implementations per host; 2 is the de facto standard from what I've read/seen online. I could and probably will do some I/O testing, but just wondering if there's a "wall" that someone else has discovered long ago (i.e. before 10GbE) that makes a 4 NIC iSCSI per host setup somewhat pointless. Just to clarify: I'm not looking for a how-to, but an explanation (link to paper, VMWare recommendation, benchmark, etc.) as to why 2-NIC configurations are the norm vs. 4-NIC iSCSI configurations. i.e. storage vendor limitations, VMKernel/initiator limitations, etc.

  Read the article

• TCP dies on a Linux laptop

  - by Roman Cheplyaka

  Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

  Read the article

• Create custom launchers in GNOME 3

  - by hochl

  I'm using Debian testing, and I have been switched to GNOME 3 by the Debian update yesterday. I'm not very comfortable with the UI. I wanted to customize everything like I had it with GNOME 2, but I simply couldn't find any way to change preferences like I'm used to. I've digged some, but all answers I could find did not help me achieve my goals. So please, if anyone knows the solution to this I'd be thankful: 1) I want several launchers that launch terminals, with different arguments and different coloring/title. I have searched everything and there seems to be no menu, no right-click, nothing which is standard in any UI I know. How can I create several launchers in this bar on the left side that launch the same application, just with different parameters? With GNOME 2 this was a piece of cake. 2) I want to switch between different terminals using ALT-TAB. Right now, I'm always just getting to the same, already-opened terminal. When I open two terminals by simply creating the second one by issuing xterm &, I still get one Terminal entry with ALT-TAB, and I have to navigate with cursor keys or mouse wheel to select one of the two xterminals. Instead, I want to open a new terminal when I click the quick launch terminal icon from the bar on the left side of the screen and navigate through them like on KDE/GNOME 2/Windows/any reasonable UI. Can this be done? 3) Is there a trick to make bluetooth devices work like on GNOME 2? Right now, my BT keyboard won't pair anymore, which, as you can imagine, makes me pretty angry. and, if anything fails: 4) How can I switch back to GNOME 2 again? :-) Honestly, who did design this? What were they smoking? I feel like I'm not allowed to do anything except start one of any application that has an icon and just with the default parameters. That can't be true, right? I feel massively restrained by this stuff :(

  Read the article

• What does this error mean in my IIS7 Failed Request Tracing report?

  - by Pure.Krome

  when I attempt to goto any page in my web application (i'm migrating the code from an asp.net web site to web application, and now testing it) .. i keep getting some not authenticated error(s) . So, i've turned on FREB and this is what it says... I'm not sure what that means? Secondly, i've also made sure that my site (or at least the default document which has been setup to be default.aspx) has anonymous on and the rest off. Proof: - C:\Windows\System32\inetsrv>appcmd list config "My Web App/default.aspx" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> C:\Windows\System32\inetsrv>appcmd list config "My Web App" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> Can someone please help?

  Read the article

• Why domain.com appears as theplant.com when hosted on hostgator?

  - by silow

  I have a script that's supposed to detect the url of its caller website. If the caller is another website, it should give something like http://callersite.com. I'm using this line of php code (though I suspect this won't matter for sysadmins) gethostbyaddr($_SERVER['REMOTE_ADDR']) I'm testing with a caller site that's hosted on hostgator. What I'm noticing though is that I don't get callersite.com, I get something like 1a.12.12ab.static.theplanet.com. I don't know what theplanet.com is and why I'm not getting caller site.com. Also what do I need to do to really get the domain of the site making a call to my script? -- Thanks for the explanation. Some have advised I use $_SERVER['HTTP_REFERER'] but it's not what I'm after. My script acts as an API. Another website makes a curl request to it and gets an output and later on presents it to the user. So http referrer gives false since the caller site.com is making a direct call to me. So any hope?

  Read the article

• What switch should we use for PCoIP?

  - by Jay R.

  We have a small lab space that seats 10 people and has 20 machines. Each machine is set to 1920x1200 resolution because the user apps are best used at that resolution. Currently the machines are all located close enough to montors that a DisplayPort cable will reach, but the pending lab remodel positions them around 80 feet or more away in racks. Our proposed solution is to use PCoIP. We purchased 10 PCoIP portals and 20 PCoIP host cards. We plan to set up a dedicated network to handle just the PCoIP traffic. After testing just one portal and one host card with a cheap 1G switch from a local office supply store, we were left with less than good impressions about the usefulness in our lab. The framerates were not spectacular and the mouse seemed jerky. Our concern is that we can't get away with the cheap 1G stuff from the store because adding more machines to the switch will just make the user experience worse. What switch would be recommended to best support our PCoIP situation? We will need to plug in at least 30 cables based on just those machines. Is there a particular feature to search for that makes a difference? Is there a switch that works best with PCoIP? Added Info: The reporting webapp for the host card shows maximum bandwidth usage to be 220000 kbps. The average appears to be around 180000 kbps. The reverse direction is much lower, like 15000 kbps.

  Read the article

• What is my BaseDN supposed to be with the following configuration of OpenLDAP?

  - by fuzzy lollipop

  I have the following in my OpenLDAP configuration. Using the latest version OpenLDAP on Centos 5.3. Installed using yum. From my /etc/openldap/slapd.conf database bdb suffix "dc=company,dc=com" rootdn "cn=Manager,dc=company,dc=com" From my /etc/openldap/ldap.conf BASE dc=company,dc=com I have successfully added an entry with ldapadd and retrieved it with ldapsearch from a local bash shell on the box. Now I am trying to get a Graphical Editor to connect to this server remotely so I can enter people from my laptop. But I am having no luck. I tried JXplorer, and it connects with Anonymous bind without me having to specify a BaseDN but I can't edit anything that way. If I try and give it a user name and password, using Manager and my rootpw I have in clear text just for testing, every GUI Client on my remote laptop complains about my BaseDN not being the correct format when I enter dc=company,dc=com and I tried cn=Manager,dc=company,dc=com. Error opening connection: [LDAP: error code 34 - invalid DN] I have tried multiple clients and all of them connect as anonymous, none let me connect authenticated where I can actually create or edit anything. I am using Manager as my username and the password from rootpw, is that correct?

  Read the article

• Prevent Linux from processing incoming ICMP Host unreachable packets

  - by bbc

  I have a test setup with one host on a network (10.1.0.0/16) talking via TCP to another one on another network (10.2.0.0/16) and a gateway in the middle. Sometimes, the TCP connection is lost and while scanning the trace (pcap), I looks like it's because of just one ICMP Host unreachable message sent by the gateway to 10.1.0.1 at some point. 10.1.0.1 then sends a TCP RST to 10.2.0.1. In my opinion, the gateway (pfSense) is broken or not configured correctly but anyway, for testing purposes, I'd like to block this kind of ICMP on the host (10.1.0.1) before it has an influence on my TCP connection (or does it? I'm not even sure). I've tried iptables: iptables -I INPUT -i eth0 -p icmp --icmp-type host-unreachable -j DROP but while it does a good job at preventing userpace applications like ping from receiving these ICMP messages, my TCP connection still comes to an end when the alleged "killer ICMP packet" is sent by the gateway. Am I right about how it is processed? If yes, then what can I do to achieve my goal?

  Read the article

• Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

  - by paul

  I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

  Read the article

• SSH not working through Double NAT

  - by d_inevitable

  I am trying to setup port forwarding for ssh through 2 NATs The first Router translates my internet IP to my outer network (10.1.7.0). In the outer network there's a second Router that does NAT to my inner network (192.168.1.0). The target server is connected to both, the outer network and the inner network. I cannot change the port forwarding options for outer router. It is currently configured to forward the SSH and HTTP port to the router for the inner network. Internet + | v +-----------------+ +------------------+ | Outer Router | | Inner Router | |-----------------| |------------------| | | SSH HTTP | | +----+ +--------------------->| | | | | | | | | | | | | +-------+---------+ +------+---------+-+ | | | | | | | | | | | | | | +------------------+ | SSH | | | | Server | | | | | |------------------| | | | +-----------> |<-------+ | | | | |HTTP (testing) | +------------------+ | | | +------v------------------+ | | Outer Workstation | +-------------------+ | |-------------------------| | Inner Workstation| | | | |-------------------| | | | | |<----------------+ +-------------------------+ | | +-------------------+ When connecting from a outer workstation to the address of the inner router, then both SSH and HTTP work fine. When connecting from the internet to my public ip with HTTP, the connection works fine as well. However SSH just times out. Most likely because the reply is not routed back properly. I suspect its either because of the SSH itself, or because the server is connected to both, the inner and outer network. Any ideas how I could resolve this issue? The routes on the server are currently: ip route show default via 10.1.7.254 dev eth0 metric 100 10.1.7.0/24 dev eth0 proto kernel scope link src 10.1.7.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.2 Do I have to change this? If so how?

  Read the article

• What may be wrong with String::ToIdentifier::EN tests?

  - by wk01

  I try to install Perl module String::ToIdentifier::EN (as depndency of DBIx::Class::Schema::Loader) but it fails on tests. I googled those errors but get no picture, where is problem: Building and testing String-ToIdentifier-EN-0.07 cp lib/String/ToIdentifier/EN.pm blib/lib/String/ToIdentifier/EN.pm cp lib/String/ToIdentifier/EN/Unicode.pm blib/lib/String/ToIdentifier/EN/Unicode.pm Manifying blib/man3/String::ToIdentifier::EN.3pm Manifying blib/man3/String::ToIdentifier::EN::Unicode.3pm PERL_DL_NONLAZY=1 /usr/bin/perl "-MExtUtils::Command::MM" "-e" "test_harness(0, 'inc', 'blib/lib', 'blib/arch')" t/00_basic.t t/10_ascii.t t/20_capitalization.t Byte order is not compatible at ../../lib/Storable.pm (autosplit into ../../lib/auto/Storable/_retrieve.al) line 380, at /home/wanradt/perl5/lib/perl5/Lingua/EN/Tagger.pm line 167 # Looks like you planned 25 tests but ran 4. # Looks like your test exited with 25 just after 4. t/00_basic.t ........... Dubious, test returned 25 (wstat 6400, 0x1900) Failed 21/25 subtests Byte order is not compatible at ../../lib/Storable.pm (autosplit into ../../lib/auto/Storable/_retrieve.al) line 380, at /home/wanradt/perl5/lib/perl5/Lingua/EN/Tagger.pm line 167 # Looks like you planned 768 tests but ran 512. # Looks like your test exited with 25 just after 512. t/10_ascii.t ........... Dubious, test returned 25 (wstat 6400, 0x1900) Failed 256/768 subtests t/20_capitalization.t .. ok Test Summary Report ------------------- t/00_basic.t (Wstat: 6400 Tests: 4 Failed: 0) Non-zero exit status: 25 Parse errors: Bad plan. You planned 25 tests but ran 4. t/10_ascii.t (Wstat: 6400 Tests: 512 Failed: 0) Non-zero exit status: 25 Parse errors: Bad plan. You planned 768 tests but ran 512. Files=3, Tests=528, 1 wallclock secs ( 0.07 usr 0.02 sys + 0.42 cusr 0.04 csys = 0.55 CPU) Result: FAIL Failed 2/3 test programs. 0/528 subtests failed. make: *** [test_dynamic] Error 255 -> FAIL Installing String::ToIdentifier::EN failed. See /home/wanradt/.cpanm/build.log for details. Byte order is not compatible at... seems a key, but to where?

  Read the article

• Windows 7 PC freezes frequently with hard disk light constantly on

  - by Senthil

  I recently replaced a defective hard disk with a new one - Windows 7 - "A disk read error occured. Press Ctrl + Alt + Del to restart" I have been using the new hard disk with a Windows 7 installation for about 4 days. Now it has started freezing frequently. Sometimes every 2 minutes and sometimes every 10 seconds. There is lots of software installed - I am a developer and my PC is full of IDEs, database servers, web servers, developer tools, testing tools, all browsers etc.. My windows is up to date as of now. I have installed ALL updates including optional drivers etc. All my installed software is up to date. I scanned my computer using Microsoft Security Essentials and found nothing malicious. I did a chkdsk /r and found no problems. I did a memory diagnostic and found no problems. When I go into safe mode, it doesn't freeze and I am able to use it normally for longer periods of time. What other steps can I take to locate the problem?

  Read the article

< Previous Page | 306 307 308 309 310 311 312 313 314 315 316 317  | Next Page >