Search Results

Search found 29876 results on 1196 pages for 'ubuntu 8 04 lts'.

Page 311/1196 | < Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >

  • No sound while playing multi-media in Ubuntu 12.04 for XPS15

    - by ved2254
    I have an XPS15 laptop, core i5, 8GB ram. Whenever I login my laptop I here the startup bongo sound. But my sound system just doesn't play anything, may it be a short audio clip or a movie. Output of lshw -c multimedia is : WARNING: you should run this program as super-user. *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:51 memory:f1c00000-f1c03fff WARNING: output may be incomplete or inaccurate, you should run this program as super-user. Headphones work just fine but there is no sound from the speakers. Is it a bug in multi-media players or ALSA?

    Read the article

  • Packard Bell TK11 Wifi not working (Ubuntu 12.10)

    - by Ingmar
    Hardware: Packard Bell EasyNote TK11BZ, BIOS version 1.15 Broadcom BCM43227 802.11 b/n/g Problem: Everything works as it should, except the wireless connection. The Wifi device is enabled in the "Additional Drivers" section of Software Sources, but does not even show up in the network manager drop-down. sudo lshw -C network: *-network UNCLAIMED description: Network controller product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0100000-f0103fff

    Read the article

  • Ubuntu 12.10 TexLive 2012: Latex file would not compile

    - by Indian
    I wrote a long report with chapters using TexLiVE 2009. When I move to 12.10, the system had upgraded to Texlive 2012. However, I found that some fonts were not working, whereas they were a part of the distribution (Texlive). Therefore, I uninstalled the whole thing (TexLive) and then reinstalled. Compilation command pdflatex myreport.tex I now have the following error while compiling: This is pdfTeX, Version 3.1415926-2.4-1.40.13 (TeX Live 2012/Debian) \write18 enabled kpathsea: Running mktexfmt pdflatex.fmt I can't find the format file 'pdflatex.fmt'! How do I solve this issue?

    Read the article

  • Software Center doesn't open (elementary luna - ubuntu 12.04)

    - by zbiba
    When i try to open software center on elementary luna i get the bellow error.... ERROR:root:DebFileApplication import Traceback (most recent call last): File "/usr/share/software-center/softwarecenter/db/init.py", line 4, in from debfile import DebFileApplication, DebFileOpenError File "/usr/share/software-center/softwarecenter/db/debfile.py", line 25, in from softwarecenter.db.application import Application, AppDetails File "/usr/share/software-center/softwarecenter/db/application.py", line 27, in import softwarecenter.distro File "/usr/share/software-center/softwarecenter/distro/init.py", line 198, in distro_instance = _get_distro() File "/usr/share/software-center/softwarecenter/distro/init.py", line 175, in _get_distro distro_class = getattr(module, distro_id) AttributeError: 'module' object has no attribute 'debian' Traceback (most recent call last): File "/usr/sbin/update-software-center", line 38, in from softwarecenter.db.update import rebuild_database File "/usr/share/software-center/softwarecenter/db/update.py", line 33, in from softwarecenter.distro import get_distro File "/usr/share/software-center/softwarecenter/distro/init.py", line 198, in distro_instance = _get_distro() File "/usr/share/software-center/softwarecenter/distro/init.py", line 175, in _get_distro distro_class = getattr(module, distro_id) AttributeError: 'module' object has no attribute 'debian'

    Read the article

  • stud ubuntu howto?

    - by Matt H
    I've just been looking at the stud init script as I thought perhaps I'm meant to create a stud.conf inside /etc/stud However, in looking through the init script it would apppear that it loads stud.conf variables into the current environment. This of course fails for some reason and you get a bunch of errors. Worse still, stud source code doesn't work with environment variables. Can someone tell me how you're actually meant to set up stud with init script as it would appear to be completely broken. Maybe I can just disable the init script and call stud from rc.local?

    Read the article

  • Ubuntu 12.04 - Unable to change brightness

    - by Raymond Standen
    So, as a number of users seem to be experiencing, I am unable to change brightness on my laptop. Using the Brightness and Lock in settings, the slider moves but brightness does not adjust. The fn keys work for volume but not for brightness. I have updated my drivers and installed all updates, however the brightness is still at maximum. I have heard that opening sudo gedit /etc/x11/xorg.conf and entering Option "RegistryDwords" "EnableBrightnessControl=1" can fix this, however when opening xorg.conf through Terminal I am greeted with a blank document... Not very reassuring. Toshiba L750 Laptop Nvidia Graphics Card Dual boot with Windows

    Read the article

  • Screen resolution is too low with open source drivers on Ubuntu 12.10

    - by Chintan Parikh
    I'm on an AMD graphics card. When I use the open source xserver-xorg-video-radeon driver, Gnome shell works fine but my screen resolution can't be set higher than 1024x768. However, when I'm on the closed source fglrx drivers, the screen resolution works fine, but gnome shell doesn't (it goes to gnome classic for some reason). Does anyone know how I can either get gnome shell to work with fglrx, or how I can set my screen resolution with xserver-xorg-video-radeon?

    Read the article

  • Ubuntu won't connect to wired network

    - by djeikyb
    I'm running 10.04, upgraded from 9.10, maybe, but probably not upgraded from 9.04. I have two wifi routers. Zeus is connected to the dsl modem. Hermes uses a wds bridge with Zeus to extend the network. My desktop (Daedalus) is ethernetted to Hermes. My laptop (Clyde) is wifi, switching to Hermes or Zeus as needed. Occasionally, as in whenever I transfer a large file from desktop to laptop, the wds bridge will die. Fixing it means restarting both routers, though it seems Hermes should boot first. This is ridiculous, and eventually I'll get around to asking you guys to help me stop it from happening. More importantly is that my desktop requires a reboot to get back on the network. WTF. ifconfig shows my nic has no ip. /etc/init.d/networking restart doesn't do anything, not even give me a lousy ip. dhcpcd eth1 grants me an ip address, but doesn't help with internet access. route -n shows what looks like my normal routing table, but pinging google.com informs me it's an unknown host. jake@daedalus:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 10.1.1.1 0.0.0.0 UG 0 0 0 eth1 It may be worth noting that I can ping both Zeus (10.1.1.1) and Hermes (10.1.1.4) and my laptop (10.1.1.55). Much obliged for any help. Rebooting is, well, trivial in this instance. But it's stupid. I switched to linux because I like the idea that if one part breaks, you fix it instead of reboot reboot reboot. I've left my poor desktop in disarray, confining myself to my little netbook. My desktop is broken, awaiting magical commands from you brilliant folk. (and yes, i know clyde the netbook should be named icarus. it was its original name. ironically the ssd burned out, and i felt it wasn't right when it came to reinstalling)

    Read the article

  • Ruby Script Runner for Ubuntu Gedit

    - by Ygam
    I have this Java script runner installed in my gedit external tools: #!/bin/sh cd $GEDIT_CURRENT_DOCUMENT_DIR if javac $GEDIT_CURRENT_DOCUMENT_NAME; then java ${GEDIT_CURRENT_DOCUMENT_NAME%\.java} else echo "Failed to compile" fi I tried modifying to it to something like this #!/bin/sh cd $GEDIT_CURRENT_DOCUMENT_DIR ruby ${GEDIT_CURRENT_DOCUMENT_NAME%\.rb} but it doesn't work. I may have missed something, I don't know what because I don't do bash scripting. Hehe

    Read the article

  • Why does fusion icon not work in Ubuntu 12.04

    - by Peter Bauer
    When I start the compiz fusion icon Application from the shell I get the following output but no icon and no GUI: $ fusion-icon --no-start * Detected Session: gnome * Searching for installed applications... Checking if settings need to be migrated ...no Checking if internal files need to be migrated ...no Backend : gconf Integration : true Profile : default Initializing decor options...done * NVIDIA on Xorg detected, exporting: __GL_YIELD=NOTHING * Using the GTK Interface

    Read the article

  • Ubuntu Unable to format 16Gb Usb Disk

    - by akshay.is.gr8
    Whenever i try to format my 16 GB usb disk using gparted it does to formating and when it refreshes then show unknown. tried disk utility as well. disk utility was able to format it into FAT but files vanish web the disk is removed and attached again. edit: the disk format completes every time but when using gparted it immediately show Unknown type file system and disk utility show FAT but when the Disk is unplugged and then connected the files are not there. either way it is unusable.

    Read the article

  • Ubuntu 14.04 has a bunch of old kernel directories

    - by NoBugs
    I saw in Disk Usage Analyzer I have 3.13.0-xx for 8 minor versions of the kernel in /lib/modules. Each is around 200MB. I remember having to go through in Synaptic and remove those old Linux versions before, but hasn't this bug been fixed? Is it just paranoid default setting, that perhaps all of the last half dozen kernels might become unbootable, so it keeps each old one around? Or do I have some developer setting enabled by accident that causes this?

    Read the article

  • Problem with the keyboard layout in Emacs (ubuntu 12.04)

    - by user61648
    I've got some problems with the keyboard layout. I have a french AZERTY keyboard. When I switch to another layout (I tested both programmer DVORAK and Greek) everything seems fine. However, in emacs, I have a more unexpected (at least for me) behavior. For example, in DVORAK, I thought to obtain: On my french Keyboard - DVORAK X - Q Alt-X - Alt-Q But I have: X - Q Alt-X - Alt-X When I press the Alt key, the layout change seems to be inactivated. I precise I didn't activated any shortcut containing the Alt key for the layout switching. Moreover, I'm not sure this behavior is restricted to Emacs, but I don't use shortcuts like Alt-... in another application. Is a such behavior normal ? And in this case, how can I use a shortcut like Alt-Q when I switch to DVORAK ?

    Read the article

  • Ubuntu 12.04 freeze on Ctrl+ALT+F1

    - by user93800
    I have Radeon card connected over HDMI to my TV. To resolve bug with HDMI-sound, I switch between virtual terminal and GNOME desktop each time the TV is switched on with CTRL+ALT+F1 and after console appear with CTRL+ALT+F7. It's ugly, but its worked for me. Since yesterday I got system freezes on CTRL+ALT+F1 - no reaction on keyboard, mouse pointer disappear at all, GNOME desktop still displayed. Probably has nothing to do with HDMI. Any suggestion how to resolve it?

    Read the article

  • Macbook 4,1 crashes when flash video (youtube) is played fullscreen (Ubuntu 12.04)

    - by Ydun
    I have searched for similar posts but those were mostly about erratic behaviour. My macbook shuts down instantly without warning when I play a youtube video fullscreen; sometimes after five minutes sometimes longer, never immediately. I can play the video normally for as long as I like, it does not crash, only when played fullscreen. I have tried Firefox and chromium, it crashes with both browsers. Anyone encountered the same thing or has a solution? thanks

    Read the article

  • Will BIOS boot mode Ubuntu install be able to boot when firmware "Fast Boot" is "Ultra Fast"?

    - by Pro Backup
    I have an AsRock mainboard with UEFI BIOS P1.50 02/14/2014. The firmware "Fast Boot" option is set to "Fast", Boot Option #1 is set to "AHCI P4: OCZ-VERT...": this is BIOS not UEFI boot. This boot disk has an MBR partitioning scheme (# parted -l | grep Partition\ Table:). Therefore Ubuntu 14.04 is installed in BIOS/CMS (Grub-PC) mode. The Ubuntu boot process ends in a text console (no GUI). There is no external graphics card in use. The stock Ubuntu kernel is replaced with Ubuntu supplied mainline 3.16.0-031600rc6-generic. dmesg outputs lines containing BIOS, like: SMBIOS 2.7 present Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored BIOS EDD facility v0.16 2004-Jun-25, 0 devices found The ASRock BIOS it selves display this help text for "Ultra Fast - Fast Boot": Ultra Fast mode is only supported by Windows 8 and the VBIOS must support UEFI GOP if you are using an external graphics card. Please notice that Ultra Fast mode will boot so fast that the only way to enter this UEFI Setup Utility is to Clear CMOS or run the Restart to UEFI utility in Windows. Assumptions: I suspect after changing UEFI setting "Fast Boot" to "Ultra Fast" that the machine will no longer boot into Ubuntu's console. I expect when first exchanging "Grub-pc" with "Grub-efi", that the machine will still be able to boot to a grub menu (thus allowing to change the "Fast Boot" setting back to "Fast" without clearing CMOS). Are these two "Fast Boot" assumptions correct, and/or, may I expect Ubuntu 14.04 running mainline kernel 3.16rc6 and Grub-efi to still boot to console after enabling UEFI Ultra Fast Boot?

    Read the article

  • make icon for firefox 24 on ubuntu 13.04

    - by nish
    how does one make a shortcut for firefox ( like any other application that has an icon) that has a command firefox 24 run from terminal. Reason i had to uninstall previous version ( 20 ) of firefox was because it was crashing often. This version ( 24 ) is stable ( and looks like it will continue to be so ). I am at present running from terminal firefox 24. Need that I make an icon which opens it and most important overlay menu ( like in mac) which is not happening at present. ( image link provided ) http://imgur.com/edk0oAl

    Read the article

  • Install reliance Driver software in ubuntu 14.04

    - by A Umar Mukthar
    I'm Using Huawei ec 150 dongle. I need to install driver software It is quiet a big task for begineers in linux. So i took this matter over here. EDIT Output of lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 12d1:140b Huawei Technologies Co., Ltd. EC1260 Wireless Data Modem HSD USB Card Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 046d:c05a Logitech, Inc. M90/M100 Optical Mouse Bus 002 Device 002: ID 046d:c31d Logitech, Inc. Media Keyboard K200 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

    Read the article

  • Ubuntu Server won't boot with "zip2: Compressed file ends unexpectedly" error

    - by Oetzi
    I am trying to boot lucid server on my new VPS but its giving me some problems. The boot gets to a point where it hangs. At this point it says: No such file `modules-2.6.31-20-server-amd64.tar.bz2' zip2: Compressed file ends unexpectedly You can use the `bzip2recover' program to attempt to recover data from undamaged sections of corrupted files. tar: Child returned status 2 tar: Exiting with failure status due to previous errors Module installation failed. Does anyone have any ideas how I might be able to fix this? Sorry that this is rather vague!

    Read the article

  • How to install Joomla in Ubuntu?

    - by Leon-TastyDev
    I have installed the lamp-server but i stuck in one certain step.. Were it says remove installation folder if i i click the button "Remove installation folder:" it says error and i guess this is because it doesn't have root previlages. So i run sudo nautilus go to the folder var/www, and remove the folder installation.. So now when i try to access my localhost No configuration file found and no installation code available. Exiting... I am confused, it asked me to remove it and now that is removed it needs it..:?

    Read the article

  • partitioning in ubuntu with gparted cant resize

    - by user288830
    I opened gparted and as i can see i have 3 partitions(or i think so) first one sda1 (236 mb) its ext2 type file and its booting point, second one is sda2(rest of the hdd 1.36 tb) extended ntfs type file and i have third one that is within the sda2 called sda5 it takes the same space as sda 2 and its file type is crypt luks, so when i try to resize the sda2 i cant resize it not for even 1 mb, i dont know if that crypt luks file is causing the problem, so i dont know what to do, by the way i can format the crypt luks(sda5) file that in inside sda 2 but i dont know if i should.Can anyone help me please? here are the pictures when i open gparted when i try to resize sda 2 i think i did use encryption i mean while it is booting i type password and its says sda5/scrypt set up succefully or something like that and then it goes to my login screen where i type username and pass that is it

    Read the article

  • apt-get 32 bit package on amd64 Ubuntu installation

    - by mario
    I was trying to get a game working. But I have Lucid Lynx on amd64 running while the game binary was 32 bit (no 64 bit version available and nobody was in the mood for recompiling). It lacked libfsml-windows1.5 to run, and apt-getting it failed. So I have to manually download the i386 packages and force install them. (No, not part of ia32libs.) Now I'm wondering if there is an automated way to have x86 packages downloaded at least on a 64-bit installation. apt-get -o apt::architecture=i386 did not work. (If you switch the architecture mode it doesn't find the package or assumes missing dependencies for existing packages all around.) Is there another tool to automate that? Possibly one which downloads the i386 packages and relocates contained libraries into /usr/lib32/ implicitely?

    Read the article

  • Ubuntu 12.04 Automounting ntfs partition

    - by kuzyt
    Ive looked everywhere to fix this problem but I cant seem to figure out why its doing this. I have the following /etc/fstab entry to mount a ntfs partition using ntfs-3g. UUID=01CD842715EC2180 /media/mediahd02 ntfs defaults,user,noexec,uid=1000,gid=1000,dmask=007,fmask=117 0 2 The volume label for this partition is "MEDIA02" So I have had no problems with the fstab mounting. The problem however is that it automounts again using MEDIA02 label. I'm not sure automounting is the right term for this as its just an empty directory. Deleting this directory and rebooting is causing it to appear again. So listing /media I see both MEDIA02 & mediahd02 htpc@htpc:~$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sdf1 during installation UUID=ec027544-b0e7-4145-99a4-905543a9781a / ext4 errors=remount-ro,noatime,discard 0 1 # swap was on /dev/sdf5 during installation UUID=1794409e-723f-41ac-9f31-ae059f377613 none swap sw 0 0 # Added all the lines below this tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0 UUID=0F70-3B06 /media/mediahd01 vfat defaults,user,noexec,uid=1000,gid=1000,dmask=007,fmask=117 0 2 UUID=01CD842715EC2180 /media/mediahd02 ntfs defaults,user,noexec,uid=1000,gid=1000,dmask=007,fmask=117 0 2 htpc@htpc:~$ cat /etc/mtab /dev/sdc1 / ext4 rw,noatime,errors=remount-ro,discard 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /tmp tmpfs rw,noatime,mode=1777 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 /dev/sdc1 /media/usbhd-sdc1 ext4 rw,relatime 0 0 /dev/sdb1 /media/mediahd02 fuseblk rw,noexec,nosuid,nodev,allow_other,default_permissions,blksize=4096 0 0 /dev/sda5 /media/mediahd01 vfat rw,noexec,nosuid,nodev,uid=1000,gid=1000,dmask=007,fmask=117 0 0 /dev/sdh1 /media/Windows_7 fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 Can someone shed some light as to why its doing this ?

    Read the article

  • Unable to change user password in Ubuntu 12.10

    - by Laphanga
    The User Password is not changing for some reason. In the terminal it says password updated successfully, $ sudo passwd [sudo] password for zaigham: Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully But when I try to log in using the new password it doesn't work. I have changed my password 2, 3 times now but still it's the same. Is that some kind of bug?

    Read the article

  • Can't install or update Ubuntu after using parameter acpi_osi = Linux

    - by Lucas Leitão
    I recently had an issue with my acer 4736z notebook because I was having a blank screen after booting the OS, then someone told me to use the parameter GRUB_CMDLINE_LINUX_DEFAULT = "quiet splash acpi_osi = Linux" after quiet splash inside the grub. It worked for me, but since then I can't install a thing or update anything on Linux because it says Removing linux-image-extra-3.5.0-17-generic ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic update-initramfs: Deleting /boot/initrd.img-3.5.0-17-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT: not found run-parts: /etc/kernel/postrm.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postrm.d at /var/lib/dpkg/info/linux-image-extra-3.5.0-17-generic.postrm line 328. dpkg: erro ao processar linux-image-extra-3.5.0-17-generic (--remove): sub-processo script post-removal instalado retornou estado de saída de erro 1 Removendo linux-image-3.5.0-17-generic ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic update-initramfs: Deleting /boot/initrd.img-3.5.0-17-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT: not found run-parts: /etc/kernel/postrm.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postrm.d at /var/lib/dpkg/info/linux-image-3.5.0-17-generic.postrm line 328. dpkg: erro ao processar linux-image-3.5.0-17-generic (--remove): sub-processo script post-removal instalado retornou estado de saída de erro 1 Erros foram encontrados durante o processamento de: linux-image-extra-3.5.0-17-generic linux-image-3.5.0-17-generic E: Sub-process /usr/bin/dpkg returned an error code (1) I already tried to remove older kernels but it gives me the same message. Do you have a clue about what should I do?

    Read the article

< Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >