Search Results

Search found 20049 results on 802 pages for 'virtual drive'.

Page 313/802 | < Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >

  • AIX: iscsi volumes disappear after reboot

    - by Dan
    We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume. The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet port for iSCSI exclusively.) When we reboot the AIX box, the iSCSI volume doesn't get mounted (which is fine; I've figured out that it fails to mount because AIX tries mounting it's volumes before starting the networking stack.) The problem is, after the server has booted it fails to redetect the iSCSI target as a physical disk. This means the volume group (iscsivg) can't go online. if I run cfgmgr -v to redetect the iscsi volume it successfully detects the iscsi target volume and creates a physical volume reference, but allocates it a different volume ID to what was defined before. eg - rootvg contains hdisk 0 and 1 iscsivg was originally defined with hdisk2 as the physical iSCSI volume. after reboot and running cfgmgr -v, AIX detects physical volumes hdisk0, hdisk11 and hdisk3. As there's no hdisk2, I can't varyon the iscsivg volume group. I can't seem any existing hdisk2 definition in the ODM. I can't easily add or change the definition of the physcial disk in the iscsivg volume group as it won't "varyon". Exporting the volume group deletes it completely, recreating the volume group by "importing" it from the reallocated disk makes it available again, but surely there's a better way? Can I force a specific hdisk drive designation for an iscsi target? How do you bring online iSCSI volumes after a reboot? I assume this "just works" with a dedicated HBA instead of a generic ethernet adapter? By the way, the iSCSI volume works fine once it's mounted; we only have problems getting it working - and only with AIX. The iSCSI array works fine with our Linux and Windows servers; ie the volumes get detected and remounted after boot time without any problems, using generic ethernet adapters. Here's some of the config from the AIX box: defined disks / devices: # lsdev hdisk0 Available 06-08-01-5,0 16 Bit LVD SCSI Disk Drive hdisk1 Available 06-08-01-8,0 16 Bit LVD SCSI Disk Drive hdisk3 Available Other iSCSI Disk Drive iscsi0 Available iSCSI Protocol Device scsi0 Available 06-08-00 PCI-X Dual Channel Ultra320 SCSI Adapter bus scsi1 Available 06-08-01 PCI-X Dual Channel Ultra320 SCSI Adapter bus ses0 Available 06-08-01-15,0 SCSI Enclosure Services Device sisscsia0 Available 06-08 PCI-X Dual Channel Ultra320 SCSI Adapter iscsi target definition in /etc/iscsi/targets: # IBM DS3300 disk array # port 1 on second controller 10.10.xx.xxx 3260 iqn.1992-01.com.lsi:1535.600a0b80005b0a7fxxxxxxxxxxxx physical volumes (after reimporting the volume group) # lspv hdisk0 0003b08a0d4936b6 rootvg active hdisk1 0003b08aaa5cb366 rootvg active hdisk3 0003b08a032d04bb iscsivg active

    Read the article

  • Chrome OS instead of Splashtop OS

    - by blsub6
    I have an HP Mini 110 with Splashtop OS as an 'instant on' OS. I've updated to the newest version which has a Chromium browser...and not too much else You know what would be really cool? The newest Chromium/Chrome OS build on there instead Can someone in the know tel me if this is even possible? (just to be clear, I don't want to put Chrome OS on my hard drive or boot to a USB drive. I want Chrome OS installed in the same place that Splashtop is installed.)

    Read the article

  • Can I set up a separate RAID 5 devices?

    - by GregH
    I have a GIGABYTE GA-P55M-UD2 motherboard in my system (Windows 7 64 bit) and currently have a Western Digital SATA 10k RPM drive in it. Is it possible to add three more SATA drives to make a single RAID 5 device that is separate from the current 10k rpm drive that I have in it? Once I enable RAID for the SATA drives, I am not required to make all of the drives part of the RAID volume am I? I can have separate RAID'ed and non-RAID'ed volumes can't I?

    Read the article

  • Firewire 800 data transfer too slow on Macbook Pro Unibody and Win7 RC

    - by dtmunir
    I'm trying to back up some data on an external hard drive and am finding the transfer rate to be unbearably slow. My environment is as follows: Macbook Pro Unibody (late 2008) Windows 7 RC, 64-bit Lacie, rugged 500GB portable hard drive I have tried using a number of methods including simple copying in Explorer, Teracopy, Crashplan, and Windows backup. I am averaging around 1MB/s which seems terribly slow. How do I identify what is the cause of this slow file transfer, and then how do I go about addressing the issue.

    Read the article

  • Server migration

    - by vinayrks
    I have to do a virtual host to another virtual host transfer , Both of them are hosted on Rackspace , OS (Red hat 4 ). client is using this server for hosting more than 10 live sites , lots of files in /var/www. I transferred all files and db from old to new , My questions: what else should I need to worry about ? how to transfer all cron job too? is I need to make entry of each site on httpd.conf or rackspace will do it , during IP swapping ?

    Read the article

  • How can I troubleshoot a "Hardware Malfunction" blue screen?

    - by AaronSieb
    My computer has suddenly started crashing to a blue screen with the following text: hardware malfunction call your hardware vendor for support *the system has halted* The crash occurs randomly during normal use. I have thus far always been able to reproduce it by transferring the contents of a large folder... But I'm not sure if this is caused by the file transfer, or simply because the transfer takes long enough for something else to trigger it. A bit about my hardware I have an dual core Intel CPU, and Asus motherboard. Video card is by nVidia, and connects via PCIe. My hard drives are in pairs, and connect via SATA to a RAID controller on the motherboard. They are configured to use a RAID0 configuration. What I've tried so far There is nothing in the Windows Event Log. WhoCrashed was unable to find any crash records. ScanDisk runs to completion (it launches prior to Windows load) and reports no errors. MemTest reports no errors (to 200% coverage). System temperatures are in the range of 40 to 50 degrees Celsius, with video card temperatures in the range of 60 to eighty degrees Celsius. I have stripped the system down to a minimal configuration (hard drive, video card, one memory module, motherboard, CPU, power supply). The problem still occurrs. However, this has allowed me to rule out a few components: It is not the video card because the problem still occurred after replacing the video card another one I had on hand. It is not the hard drive or anything software related because the problem occurred after a fresh installation of Windows on a replacement hard drive. It is not the hard drive cables because I replaced those with new ones and still had the problem. It is not the power supply because the problem still occurred after replacing the power supply with another one I had on hand. It is probably not the memory because I've tried three different memory modules in three different memory slots and was still able to replicate the issue. Is there anything I can do to confirm what's causing the issue? At the moment it seems as though it must be either the motherboard or CPU, but those are both difficult components to replace... In addition, both components are relatively new (two to three years old). I will gladly edit in any additional information I can get my hands on, and/or focus the question as I can find more details...

    Read the article

  • Install Ubuntu 12.04 in UEFI mode on a HP Pavilion dv6-6c40ca

    - by Marlen T. B.
    I have recently (as of July 2012) bought a HP Pavilion dv6-6c40ca laptop. It came pre-installed with Windows 7 on an MBR. I installed Ubuntu 12.04 on it on a GPT partition in what I think is BIOS emulation mode. I made a BIOS-Grub partition so the install didn't fail. That is what it is for .. right? Now I want to upgrade to UEFI mode. How would I Install Ubuntu 12.04 in UEFI mode on a HP Pavilion dv6-6c40ca. Or is it impossible? My laptop, despite its new age may not be UEFI 2.0+ capable. If it isn't how can I install a software UEFI (i.e. a DUET such as the one by tianocore). Or is this too impossible? A link to my laptop's specs is: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03137924&tmp_task=prodinfoCategory&cc=ca&dlc=en&lang=en&lc=en&product=5218530 My laptop should have a UEFI given this link from HP http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c01442956#N218. And from the link I draw a quote: That means most notebooks distributed with Windows Vista, and all notebooks distributed with Windows 7, have the UEFI environment. My laptop had Windows 7 Home Premium pre-installed. OK. Following the comments so far -- NOTE: I am trying to do this on an external drive so I can see if it works. I have partitioned the drive using GParted as a GPT drive. Created a 200MB partition at the beginning of the drive with a FAT32 file system. Given the 200MB partition a label of "EFI". Set the boot flag on the 200MB partition. What should a do next to install Ubuntu 12.04? Given the link: https://help.ubuntu.com/community/UEFIBooting#Selecting_the_.28U.29EFI_Graphic_Protocol In my first read through (just to see if I will understand everything before I start) I get to step 2.3 Install GRUB2 in (U)EFI systems The first line is Boot into Linux (any live ISO) preferably in UEFI mode. Um .. how do you tell what mode your live CD is in?! And how do you change it if the mode is wrong?

    Read the article

  • window login when web application is using network share in IIS 6

    - by James
    Hi, I have installed a web application which is configured using a network drive But i am keep getting a pop up asking for credentials looking in the event log, the network logon is set to my domain/account which looks fine however caller user name is empty (not sure if this is an issue) the application works fine when i use a local drive the application also runs fine when i set "connect as" user the application also works fine when a share on the local machine is used!! direct asses using the unc path is not a problem Please advise what i can do or should check Thanks and Regards, James

    Read the article

  • Data loss through permissions change?

    - by charliehorse55
    I seem to have deleted some files on my media drive, simply by changing the permissions. The Story I have many operating systems installed on my computer, and constantly switch between them. I bought a 1TB HD and formatted it as HFS+ (not journaled). It worked well between OSX and all of my linux installations while having much better metadata support than NTFS. I never synced the UIDs for my operating systems so the permissions were always doing funny things. Yesterday I tried to fix the permissions by first changing the UIDs of the other operating systems to match OSX, and then changing the file ownership of all files on the drive to match OSX. About 50% of the files on the drive were originally owned by OSX, the other half were owned by the various linux installations. I started to try and change the file permissions for the folders, and that's when it went south. The Commands These commands were run recursively on the one section of the drive. sudo chflags nouchg sudo chflags -N sudo chown myusername sudo chmod 666 sudo chgrp staff The Bad Sometime during the execution of these commands, all of the files belonging to OSX were deleted. If a folder had linux based files it would remain intact but any folder containing exclusively OSX files was erased. If a folder containing linux files also contained a subfolder with only OSX files, the sub folder would remain but is inaccesible and displays a file size of 0 bytes. Luckily these commands were only run on the videos folder, I also have a music folder with the same issue but I did not execute any of these commands on it. Effectively I have examples of the file permissions for all 3 states - the linux files before and after, and the OSX files before. OSX File Before -rw-r--r--@ 1 charliehorse 1000 3634241 15 Nov 2008 /path/to/file com.apple.FinderInfo 32 Linux File before: -rw-r--r--@ 1 charliehorse 1000 5321776 20 Sep 2002 /path/to/file/ com.apple.FinderInfo 32 Linux File After (Read only): (Different file, but I believe the same permissions originally) -rw-rw-rw-@ 1 charliehorse staff 366982610 17 Jun 2008 /path/to/file com.apple.FinderInfo 32 These files still exist so if there are any other commands to run on them to determine what has happened here, I can do that. EDIT Running ls on one of the "empty" deleted OSX folders yields this: ls: .: Permission denied ls: ..: Permission denied ls: subdirA: Permission denied ls: subdirB: Permission denied ls: subdirC: Permission denied ls: subdirD: Permission denied I believe my files might still be there, but the permissions are screwed.

    Read the article

  • My computer freezes irregularly

    - by Manhim
    My computer started to freeze at irregular times for 3 weeks now. Please note that this question change with each things that i try. (For additional details) What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. Sometimes my G-15 LCD screen flickers and caracters gets caried around temporary under heavy load. Now, most of the times, the BIOS hard disks boot order gets reversed for some reason and I have to put it to the right one and save each times I boot. (Might be unrelated, not sure, but it first started yesterday) Sometimes the BIOS doesn't detect my 750GB hard drive plugged in SATA1. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 45-55. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu Ran 6 short different CPU stress test on Fedora 15 (Haven't found any complete stress testers for Linux) and it didn't crash. Changed the thermal paste to some Artic Silver 5 for my CPU and stress tested the CPU, temperature was at 50 idle, then 64 highest and slowly went down to 62 during the test. Ran some stress testing with a temporary graphic card and it went ok. Ran furmark stress test with my original graphic card and it freezed again. GPU had a temp of 74C, a CPU temp of 58C and a mobo temp of 40C or 45C (Dunno which one it is from SpeedFan). Ran a furmark stress test and a CPU stress test at the same time, results: http://pastebin.com/2t6PLpdJ I have been using my computer without stressing it for about 2 hours now and no crashes yet. I also have disabled the AMD Cool'n'quiet function on the BIOS for a more regular power to the CPU. When I ran Furmark without C'n'q my computer didn't freeze but I had a "Driver Kernel Error" that have recovered (And Furmark crashed) all that while running a CPU stress test. The computer eventually frozed without me being at it, but this time my screen just went on sleep and I couldn't wake it. Using the stability tester in nTune my computer freezed again (In the same manner as before). I notived that Speedfan gives me a -12V of -16.97V and a -5V of -8.78V. I wonder if these numbers are reliable and if they are good or bad. I have swapped my G-15 with another basic USB keyboard (HP) and I have ran furmark for about 10 minutes with a CPU stability test running each 60 seconds for 30 seconds and my computer haven't crashed yet. Ran some more extended tests without my G-15 and it freezed like it usually do. Removed the nForce Hard disk controler. Disabled command queuing in the NVIDIA nForce SATA Controller for both port 0 and port 1 (Errors from the logs) Used CPUID HwMonitor, here are the voltages: http://pastebin.com/dfM7p4jV Changed some configurations in the motherboard BIOS: Disabled PEG Link Mode, Changed AI Tuning to Standard, Disabled the 1394 Controller, Disabled HD Audio, Disabled JMicron RAID controller and Disabled SATA Raid. When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) When my Graphic card and my CPU are stressed. Sometimes when my Graphic card is stressed. Never happenned while stressing only the CPU. Sometimes when my CPU is stressed. Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) Event logs (Warnings, errors and critical errors) for the last 24 hours: http://pastebin.com/Bvvk31T7 My current to-try list Reinstall the drivers and software 1 by 1 and do extensive stress testing between each. Update the BIOS firmware to the most recent stable one. Change my motherboard. Status updates Keeping only the last 3 (28/06 04pm) More stress testing and still pass the tests. (28/06 03pm) Been stress testing for 10 minute straight now and 5 minutes with both CPU and GPU being stressed at the same time. (28/06 03pm) Stress-testing right now, so far no problems. A little hope Tests with Furmark and Prime95. Testing Windows bare-bone: 30 Minutes stress, no freeze. Installing an Anti-virus and some software, restarting computer. Testing with Anti-virus and some software (No drivers installed): 30 Minutes stress, no freeze. Installing audio drivers, restarting computer. Testing with the audio drivers: 30 Minutes stress, no freeze. Installing the latest graphic drivers from EVGA's website (without 3d vision since I don't use it), restarting computer. Testing with the graphic drivers: 30 Minutes stress, no freeze. Configuring Windows to my liking and installing more softwares. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

    Read the article

  • Disk Image Tools for Windows Server 2008

    - by Jon Rauschenberger
    I have a Windows Server 2008 X64 machine that I need to swap the boot drive on. I'd like to use a disk image/restore utility to make an image of the boot partition and restore that to the new drive. Does anyone know of a free or reasonably priced tool that can do this? I know that Acronis True Image will do it, but you need to have their server product to restore images of a server OS and it's prohibitively expensive ($850). Thanks, jon

    Read the article

  • missing files after reassemble of RAID-5

    - by Kris_R
    I had to open my file-server's housing on Sunday to replace a faulty fan. What I didn't see was that one of the sata-cables was not properly connected. The 1st thing I did after a reboot was a check of the RAID status and it showed immediately that one drive is missing. Till this moment the device was not used (however it was mounted, so I'm not 100% sure that system did nothing). I stopped md0 and re-plugged the cable: mdadm --stop /dev/md0 poweroff After another reboot I checked the removed drive: mdadm --examine /dev/sdd1 ... Checksum : 3276bc1d - correct Events : 315782 Layout : left-symmetric Chunk Size : 32K Number Major Minor RaidDevice State this 0 8 49 0 active sync /dev/sdd1 0 0 8 49 0 active sync /dev/sdd1 1 1 8 65 1 active sync /dev/sde1 2 2 8 33 2 active sync /dev/sdc1 3 3 8 17 3 active sync /dev/sdb1 I was a bit surprised that it was shown as active (even if earlier mdadm said, that this device was removed from array) and its checksum was OK. I recreated RAID with: mdadm --assemble /dev/md0 --scan The command mdadm --detail /dev/md0 showed that all drives were running and system was in "clean" state. I mounted the device md0 and then came hic-cup. I wanted to work on one of the last files that I had been using before all the situation and it was not there. In another place I missed actually all files from the directory where I was working. As far as I can see most of the files that are older than a few days are intact but some newer ones are missing. Now the big question: what would be your advice? Is there a way to get these data? I thought about removing the drive that was earlier labeled by mdadm and rebuild array with another empty HDD. I've found that after re-assemble the "broken" drive has another label (changed from sdd to sdb). Can this have influence on rebuilt process? If yes, how to reassemble the array properly? I'm sure the SATA-cables are connected still in the same order to the controller. p.s. Please no advises like "restore from backup". I'm doing back-ups on Sunday's night and this happened in the late afternoon, so backup is not really options for me. p.s.s. I asked this question on Unix&Linux but no answer came up during last two days. I'm getting quite anxious. Sorry for duplicating if any of you reading the other forum.

    Read the article

  • pci-express ssd running an OS

    - by tom
    Hi, Simple question really, is it possible to install an OS such as windows or ubuntu on a PCI-Express SSD (solid state drive)? And if so is it as straight forward as selecting that drive on install? Thanks Tom

    Read the article

  • Windows Server 2008 and eSata External Connection

    - by Tyler
    Can anyone recommend a good eSATA PCIe card for Windows Server 2008 (x64)? I bought a J-Micron JMB363 and it's recognized by the OS and I can install one of their reference drivers, but it's not picking up the drive I have attached to it. Basically, I want to be able to transfer exported Hyper-V machines quickly to an external drive, and it seems that using one of these eSATA cards is the way to go.

    Read the article

  • Windows Backup (2008 R2) recovery and timezone

    - by GrZeCh
    Hello, does difference between timezones on Windows Server 2008 where backup was made and reovery console makes difference? Recovery console (wbadmin from command line too) is not finding any backup on local hard drive connected to server. Thanks EDIT: I'm working on Windows Server 2008 R2 EDIT2: This is not related to timezone. When I connected backup hard drive from Windows 2008 R2 Release Candidate recovery console runned from RTM system version DVD found stored backups from it without problems.

    Read the article

  • How to restore a VirtualBox image given the .vdi file

    - by Ramon Tayag
    Background I have VirtualBox on Linux and recently the drive with the system files failed on me. I'm able to use the Live CD to view the files of the storage drive, and through this, I can copy my data files to another computer while I work on this one. How do I load the .vdi in another computer (or in this case, the fresh install of Ubuntu)? I see many samples online of how to export it, but it assumes the host is currently working. Thanks!

    Read the article

  • Issues with Server 2012 using DFSR running on Hyper-V 2012

    - by Bryan
    We have a number of Server 2012 systems, all of which run virtualised on Hyper-V 2012 server. We are having problems with two such virtual instances, both of which are used as file servers, whereby they occasionally stop responding to requests to serve files to clients. After logging on to the server, attempts to shut it down gracefully fail (no error, it just fails to acknowledge a shutdown request). Recovery is a case of power cycling the server(s) from the Hyper-V console. These two servers don't server a large number of users (one serves no more than 6 users, and the other serves around 20 users), they are in the same domain, but on different physical hardware (and at different sites). They don't lock up at the same time. They both use DFSR to replicate a fairly large amount of data between themselves (200GB) over ADSL connections, this is working fine, and we have been using DFSR to do this on the previous two generations of server OS we have used (Server 2008 R2 and Server 2003 - both of which were physical installs however). Today, when one of the servers crashed, I noticed an entry in the event log, which looked similar to the following: Log Name: Application Source: ESENT Date: 27/11/2012 10:25:55 Event ID: 533 Task Category: General Level: Warning Keywords: Classic User: N/A Computer: HAL-FS-01.example.com Description: DFSRs (1500) \\.\E:\System Volume Information\DFSR\database_C8CC_101_CC00_EC0E\ dfsr.db: A request to write to the file "\\.\E:\System Volume Information\ DFSR\database_C8CC_101_CC00_EC0E\fsr.log" at offset 4423680 (0x0000000000438000) for 4096 (0x00001000) bytes has not completed for 36 second(s). This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. When the server started up again, I went to find the event log entry to investigate further and found that the event log entry was no longer there (I assume it was in memory but failed to write to disk before the server was powered off, for the reason mentioned in the message). I found the above message by searching back further in the event log. Both of these virtual servers have their E: volumes fully allocated as opposed to dynamically expanding, and there are no other issues on any of the other virtual servers (which include server 2012, server 2008 R2 and Ubuntu 12.04 x64). There are no signs of IO, memory or CPU starvation on the host systems. I've used performance counters on the affected virtual servers to monitor memory usage (including non paged pool usage), as well as CPU and network utilisation, and none of these show any signs of trouble when the issue arises. I would have thought our configuration isn't that uncommon, so I'm wondering if anyone else has seen this, and managed to resolve the problem?

    Read the article

  • Macrium Reflect Recovery Linux Recovery Disc hangs up on booting

    - by user8583
    I created an image of my system with macrium reflect freeware program and stored the image on an usb external hard drive. However the macrium reflect linux recovery disc on startup hangs up of the first three lines of instructions and therefore I cannot access the image on the usb external hard drive if I wish to recover my system. I have a Lenovo laptop with the Windows-7 Home Premium operating system. What can be done to ensure that the recovery disc will work?

    Read the article

  • chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

    - by Zian Choy
    When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

    Read the article

  • Disc2vhd and partitions question

    - by dotnetdev
    Hi, I am using Disc2Vhd to make a vhd of my drive. Does the tool support partitions? My partitions of C:\ are listed as both drives and volumes. In short, is there any issue when I select both partitions that make one physical drive? Thanks

    Read the article

  • How to restore using DriveImage XML image if unable to make a BartPE CD

    - by CChriss
    I have a Windows Vista laptop that won't boot at all. On the D: drive I have DriveImage XML images of C: drive, but I don't have a BartPE boot CD and I don't have a Vista install CD. How can I image the C: using the images on D: if I can't make a BartPE CD because I can't boot to Windows? Is there a BartPE (with DriveImage XML plugin) iso I can download from somewhere, or what can I do? Thanks.

    Read the article

  • What are the steps to set up a Hyper-V solution with one NIC

    - by Cameron Aziz
    I have successfully installed centos on a virtual machine via Hyper-V on Windows Server 2008 R2. This server has one NIC. I have created a virtual NIC, and virtual subnet, and within the virtual machine (via console) I can ping the gateway. But not google. Is there certain steps I am missing, I feel like I'm one setting away. Im not sure what other information would be useful. Here is the ipconfig of the host: Ethernet adapter vNIC losangeles1_1: Connection-specific DNS Suffix .. : IPv4 Address. . . . . . . . . . . : 10.10.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix .. : IPv4 Address. . . . . . . . . . . : 72.51.43.43 Subnet Mask . . . . . . . . . . . : 255.255.255.192 Default Gateway . . . . . . . . . : 72.51.43.1

    Read the article

  • Make backup image (.tib/.vhd) as my main operating system?

    - by Joann
    My old hard drive is dying so I want to move my Windows 7 operating system to another hard drive. They say cloning using Acronis would do the trick, but for some reason it refuses to work. I also tried EASEUS Todo Backup, but it doesn't work either. Can you recommend some suggestions on how to transfer my operating system? I heard about converting .tib to .vhd and then booting from it, but does that achieve the same effect as cloning?

    Read the article

< Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >