Search Results

Search found 18911 results on 757 pages for 'device manager'.

Page 315/757 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• Windows Vista - Can Boot into Safe Mode Command Prompt, Cannot Access Flash Drive

  - by Adam

  Hey there, Got a laptop dropped into my lap. Has Vista installed. Normal boot never gets past the login screen. Safe mode will get past, but just barely. I can try and start the task manager at that point, but it never opens. Only reliable way to do anything I've got is the safe mode command prompt... Boots up and logs in fine. I can't see anything noticably wrong via regedit, but it's been a long time since I've had to fix up a Windows box... not sure that I would. Problem I'm having, is that I want to run ComboFix/etc, but have no way to get them on there... When I pop a flash drive in, it seems to mount it (flash drive flickers as normal) but it never seems to be mounted... I cannot access it through any drive letter on the command line. I managed to start the device manager (devmgmt.msc) and the flash drive was recognized and listed... Any ideas on how to get this thing going again? (Short of a reinstall.) (It has no CD drive, either, so burning files to CD would not be easy...) Thanks! Adam

  Read the article

• VPN issue: SSTP Service service started and then stopped

  - by Ampersand

  When I was trying to set up a VPN connect on my laptop running Windows 7 Ultimate, I got this error: Network Connections Cannot load the Remote Access Connection Manager service. Error 711: The operation could not finish because it could not start the Remote Access Connection Manager service in time. Please try the operation again. I traced through some service dependencies and discovered that Secure Socket Tunneling Protocol Service was set to Manual. However, when I try to manually start the service, I get: Services The Secure Socket Tunneling Protocol Service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs. Setting all the services involved to Automatic did not help. SSTP just showed Automatic and Stopped in the Services panel. I found a solution that involved booting in Safe Mode and deleting the contents of C:\Windows\System32\LogFiles\WMI\RtBackup. This solution worked, and I could set up a vpn connection, but only until I rebooted again. TL;DR I'm looking for a way to permanently enable Secure Socket Tunneling Protocol Service and other vpn-related services permanently so I don't have to reboot into safe mode and delete files every time I need to connect to a vpn.

  Read the article

• Disable XP disk check using FAT32

  - by mike xie

  Right now I'm using Windows XP and Macintosh on my MacBook Pro via Bootcamp. Sometimes my XP would crash and when I restarted it it would have to go through disk check, although it says I can skip it by pushing a key, but this never worked for me. I did a bit of research online on how to disable disk check and found chkntfs /x c: but when I tried this out in my cmd it said the disk is FAT32 format. I tried to convert my C: drive from FAT32 to NTFS by using convert c: /FS:NTFS but when I tried this it told me to locate my C: drive. I tried to type C: and Bootcamp but couldn't really get past it. I later saw someone said to use this: Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager] "AutoChkTimeOut"=dword:0000000 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager] "BootExecute"=hex(7):61,00,75,00,74,00,6f,00,63,00,68,00,65,00,63,00,6b,00,20,\ 00,61,00,75,00,74,00,6f,00,63,00,68,00,6b,00,20,00,2a,00,00,00,00,00 [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon] "SFCScan"=dword:00000000 [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\MyComputer\cleanuppath] @=hex(2):25,00,53,00,79,00,73,00,74,00,65,00,6d,00,52,00,6f,00,6f,00,74,00,25,\ 00,5c,00,73,00,79,00,73,00,74,00,65,00,6d,00,33,00,32,00,5c,00,63,00,6c,00,\ 65,00,61,00,6e,00,6d,00,67,00,72,00,2e,00,65,00,78,00,65,00,20,00,2f,00,44,\ 00,20,00,25,00,63,00,00,00 (Save it as .reg and execute it) I have just tried running it but am not really sure if it did anything (my laptop hasn't crashed yet :) ) Firstly, I am wondering if someone can tell me how to check if that script worked? Secondly, if that script didn't work, does anyone have any solution for these problems? Is there another way to disable disk check or is there another way for me to change my FAT32 to NTFS?

  Read the article

• Virtual Wifi Issue Windows 7

  - by Matt

  Lately I've been trying to use my laptop as a wireless router in my room. I have it connected to my school's network through ethernet, and I want to set up wireless so that I can use Wifi on my Android phone and iPod Touch. In the past, I used Connectify, but I started having an issue where my phone would find the network, connect, attempt to get the IP, and then suddenly the network would disappear. Then it'd pop up again, and the same process would happen over and over. I decided that I'd totally uninstall Connectify, but after that, neither Virtual Router Manager nor the command prompt could create a viable network either. My phone and even my iPod now encounter the same problem. Neither can successfully connect. So evidently there is something wrong with the laptop's virtual wifi feature, and I have no idea what that could be. I've tried enabling certain services that virtual wifi supposedly relies on, but some of them don't start, namely Remote Access Connection Manager. But I also have read that these enable on their own and that if they are normally not enabled it's fine. Furthermore, I even uninstalled and reinstalled the drivers for my wireless card. Any ideas as to why my virtual wifi won't function? Anything? I really would love to get this working...

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• Oracle with Kerberos authentication and Windows 2003 Server as KDC

  - by Supaplex

  Hello everyone. I am running Oracle 10.2 on a Windows 2003 Server SP2 which is also the domain controller on the network. I wish to switch authentication method from NTS to Kerberos. I have spent a lot of time trying to configure Oracle with Kerberos authentication from the Oracle Advanced Security option from the Net Manager utility. I have disabled NTS so Kerberos is promoted as the preferred authentication method. But as soon as the configuration is saved from Net Manager and I restart the Oracle server service, Oracle will not start. I don't know what Oracle is complaining about, because I don't know where to look for the Oracle error log. My first question is: how can I figure out what's bugging Oracle? My second question: is there a good tutorial for setting up Oracle on a Windows 2003 with Kerberos Authentication, where the Windows 2003 Server is the KDC? Maybe there is a book I can get? I have read Oracles own guide, but it is mostly for Linux/Unix. Thanks a lot!

  Read the article

• Millions of files in php's tmp error - how to delete?

  - by Jonatan Littke

  Hey. I've got a tmp-folder with 14 million php session files in my home directory. At least that's what I think it is, it's not like I could ls it or anything. How can I empty this folder? I've tried using find with the -exec rm {} \; commands but that didn't work. ls 'sess_0*' | xargs rm did neither. I'm currently running rm -rf tmp but after two hours the folder appears to be the same size. REFERENCE INFO: I suddenly encountered an error where SESSIONS could no longer be written to disk: [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: open(/var/www/clients/client1/web1/tmp/sess_8e12742b62aa68a3f9476ec80222bbfb, O_RDWR) failed: No space left on device (28) in Unknown on line 0 [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/www/clients/client1/web1/tmp) in Unknown on line 0 I ran: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/md0 457G 126G 308G 29% / tmpfs 1.8G 0 1.8G 0% /lib/init/rw udev 10M 664K 9.4M 7% /dev tmpfs 1.8G 0 1.8G 0% /dev/shm But as you can see, the disk isn't full. So I had a look in the syslog which says the following 20 times per second: kernel: [19570794.361241] EXT3-fs warning (device md0): ext3_dx_add_entry: Directory index full! This led me thinking to a full folder, obviously, but since my web folder only has 60k files (having counted them), I guessed it was the tmp folder (the local one, for this instance of php) that messed things up. Some commands I ran: $ sudo ls sess_a* | xargs rm -f bash: /usr/bin/sudo: Argument list too long find . -exec rm {} \; rm: cannot remove directory '.' find: cannot fork: Cannot allocate memory I'm running Debian Lenny, php5, ISPConfig, SuEXEC and Fast-CGI.

  Read the article

• Problems with synaptic touchpad

  - by penlite

  The "enhanced" features of the synaptics touchpad (ie scroll, pinch zoom) on my windows 7 64 bit dell studio 17 only work intermittently. This was an issue with the original OEM driver and also with the new driver from synaptics - please do not suggest that i update, reinstall, install as administrator, check or jiggle the driver - if i hear that one more time i will freak out. I have researched this for days and appears to be a common problem without a solution (many suggestions to update the driver though -argh). Dell and synaptics have not been helpful. I have checked that syntpehn.exe and syntphelper.exe are running (sometimes the UAC seems to block syntpehn.exe from running at startup). When the touchpad fails i can still use it to control the pointer and access the synaptics settings although some of the options are disabled (greyed out or simply unresponsive). It is the only pointing device i have installed - i had a logitech trackball attached but have uninstalled all software and drivers (including hidden devices) as per synaptic. It is also the only device using IRQ 12. Any help would be greatly appreciated except "update the driver".

  Read the article

• Setfacl configuration issue in Linux

  - by Balualways

  I am configuring a Linux Server with ACL[Access Control Lists]. It is not allowing me to perform setfacl operation on one of the directoriy /xfiles. I am able to perform the setfacl on other directories as /tmp /op/applocal/. I am getting the error as : root@asifdl01devv # setfacl -m user:eqtrd:rw-,user:feedmgr:r--,user::---,group::r--,mask:rw-,other:--- /xfiles/change1/testfile setfacl: /xfiles/change1/testfile: Operation not supported I have defined my /etc/fstab as /dev/ROOTVG/rootlv / ext3 defaults 1 1 /dev/ROOTVG/varlv /var ext3 defaults 1 2 /dev/ROOTVG/optlv /opt ext3 defaults 1 2 /dev/ROOTVG/crashlv /var/crash ext3 defaults 1 2 /dev/ROOTVG/tmplv /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/ROOTVG/swaplv swap swap defaults 0 0 /dev/APPVG/home /home ext3 defaults 1 2 /dev/APPVG/archives /archives ext3 defaults 1 2 /dev/APPVG/test /test ext3 defaults 1 2 /dev/APPVG/oracle /opt/oracle ext3 defaults 1 2 /dev/APPVG/ifeeds /xfiles ext3 defaults 1 2 I have a solaris server where the vfstab is defined as cat vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - /dev/vx/dsk/bootdg/swapvol - - swap - no - swap - /tmp tmpfs - yes size=1024m /dev/vx/dsk/bootdg/rootvol /dev/vx/rdsk/bootdg/rootvol / ufs 1 no logging /dev/vx/dsk/bootdg/var /dev/vx/rdsk/bootdg/var /var ufs 1 no logging /dev/vx/dsk/bootdg/home /dev/vx/rdsk/bootdg/home /home ufs 2 yes logging /dev/vx/dsk/APP/test /dev/vx/rdsk/APP/test /test vxfs 3 yes - /dev/vx/dsk/APP/archives /dev/vx/rdsk/APP/archives /archives vxfs 3 yes - /dev/vx/dsk/APP/oracle /dev/vx/rdsk/APP/oracle /opt/oracle vxfs 3 yes - /dev/vx/dsk/APP/xfiles /dev/vx/rdsk/APP/xfiles /xfiles vxfs 3 yes - I am not able to find out the issue. Any help would be appreciated.

  Read the article

• Managing multiple Apache proxies simultaneously (mod_proxy_balancer)

  - by Hank

  The frontend of my web application is formed by currently two Apache reverse proxies, using mod_proxy_balancer to distribute traffic over a number of backend application servers. Both frontend reverse proxies, running on separate hosts, are accessible from the internet. DNS round robin distributes traffic over both. In the future, the number of reverse proxies is likely to grow, since the webapplication is very bandwidth-heavy. My question is: how do I keep the state of both reverse balancers / proxies in sync? For example, for maintenance purposes, I might want to reduce the load on one of the backend appservers. Currently I can do that by accessing the Balancer-Manager web form on each proxy, and change the distribution rules. But I have to do that on each proxy manually and make sure I enter the same stuff. Is it possible to "link" multiple instances of mod_proxy_balancer? Or is there a tool out there that connects to a number of instances, and updates all with the same information? Update: The tool should retrieve the runtime status and make runtime changes, just like the existing Balancer-Manager, only for a number of proxies - not just for one. Modification of configuration files is not what I'm interested in (as there are plenty tools for that).

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• Change authentication wifi WPA to WEP on Windows 8

  - by Kites

  I use netsh wlan set hostednetwork mode=allow ssid=Kites key=phambaoViet netsh wlan start hostednetwork To share WiFi from LAN network on laptop (Windows 8) to my other device. When I show information netsh wlan show hostednetwork the supported authentication is WPA. My device support authentication WEP only. How can I change the authentication to WEP? Infomation: Interface name: Wi-Fi Driver : Qualcomm Atheros AR9002WB-1NG Wireless Network A dapter Vendor : Qualcomm Atheros Communications Inc. Provider : Microsoft Date : 03/07/2012 Version : 3.0.0.130 INF file : C:\Windows\INF\netathrx.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g 802.11n FIPS 140-2 mode supported : Yes 802.11w Management Frame Protection supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Vendor defined Vendor defined Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP Vendor defined Vendor defined

  Read the article

• Diagnosing a BSOD involving USB

  - by David Ebbo

  [Running Win7 Ultimate 64 bit] My new HP Pavilion Elite HPE-450t has been plagued by BSDO crashes since I got it about 5 weeks ago. The crashes are somewhat rare, sometimes not occurring for 3 or 4 days. I have spent a lot of time trying to isolate the device that could be at fault, but I have seen crashes with only the keyboard and mouse plugged in (as USB devices), and I tried two sets of keyboard/mouse, so I'm running out of ideas. :( The WhoCrashed tool gave this info about my latest BSOD: crash dump file: C:\Windows\Minidump\121310-11887-01.dmp This was probably caused by the following module: usbport.sys (USBPORT+0x2DE4E) Bugcheck code: 0xFE (0x5, 0xFFFFFA8008F571A0, 0x80863B34, 0xFFFFFA80092F2510) Error: BUGCODE_USB_DRIVER file path: C:\Windows\system32\drivers\usbport.sys product: Microsoft® Windows® Operating System company: Microsoft Corporation description: USB 1.1 & 2.0 Port Driver Bug check description: This indicates that an error has occurred in a Universal Serial Bus (USB) driver. The crash took place in a standard Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system which cannot be identified at this time. I looked at http://msdn.microsoft.com/en-us/library/ff560407(VS.85).aspx, and for Parameter1 = 0x5, it says "A hardware failure has occurred due to a bad physical address found in a hardware data structure. This is not due to a driver bug". Should I conclude that it's a hardware issue in the machine itself, rather than a bad USB driver or USB device? Here is the MiniDump, in case someone can get more info out of it: http://ewt52q.blu.livefilestore.com/y1peS4Ce8nSK1SXghzMDoxDWXlaEu-EKCJsv25y8y5DXXIUzZ9U0_tYgFJXd939fykwa0zRmx98IW0PYG18GioqKAuARYjtspSA/121310-11887-01.dmp?download&psid=2

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

• How do I disable the firewall on blackberry?

  - by user15660

  I own a Blackberry 9630 tour.(Sprint). The firewall is enabled with a lock sign and grayed out. I'm not able to disable it. Because of this many of my blackberry apps don't work as it gives a message "The application has tried to open a connection that's not allowed by your IT policy". I tried all options and there's nothing to disable. This is a personal blackberry and I don't have an IT policy on it. I did all methods like wiping, formatting/resetting to factory settings acc. to blackberry site by running their reset app from PC etc etc. but nothing works I tried CrackUtil for blackberry and that worked and wiped the blackberry. I restored my bb and started using it just to notice that the firewall is enabled back after a desktop manager connection to PC. I even made sure the policy.bin file on PC is a regular one with no IT policy. How do I get this disabled? I had the same problem on my old blackberry 8330 and crackutil disabled the firewall. but after a few days after a desktop manager update of blackberry OS and other small stuff the firewall got enabled again. Please give me a solutions to disable the firewall on blackberry

  Read the article

• GRUB reporting wrong partition type

  - by plok

  It all started when I had to replace one of the disks that the software RAID 1 on this machine currently uses. From that moment on I have not been able to boot to the Windows XP that is installed on the fourth hard drive, /dev/sdd. I am almost positive that the problem is related not to Windows but to GRUB, as if I unplug all the other hard drives so that the Windows XP disk is now /dev/sda it boots with no problem. The problem seems to be that GRUB detects a wrong partition type, which I understand suggest that something is really messed up. This is what I get when I try to follow the steps that until now had worked like a charm: grub> map (hd0) (hd3) grub> map (hd3) (hd0) grub> root (hd3,0) Filesystem type is ext2fs, partition type 0xfd 0xfd? That doesn't make sense. /dev/sdb and sdc are 0xfd (Linux raid), but not /dev/sdd: edel:~# fdisk -l [...] Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00048d89 Device Boot Start End Blocks Id System /dev/sdd1 * 1 30400 244187968+ 7 HPFS/NTFS edel:/boot/grub# cat device.map (hd0) /dev/sda (hd1) /dev/sdb (hd2) /dev/sdc (hd3) /dev/sdd I have been trying to work this out for hours, to no avail. Can anyone point me in the right direction?

  Read the article

• Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

  - by Matt

  I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

  Read the article

• How do I boot [embedded] linux from sd card?

  - by Brandon Yates

  I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

  Read the article

• Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

  - by music2myear

  Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

  Read the article

• Event Log "Wake Source" when system wakes from sleep

  - by Doltknuckle

  So I've been troubleshooting sleep timers for our systems and have run across an interesting issue. I need a way to report how long a system was awake after a number of different inputs. Now, I've discovered that the System Log tracks wake and sleep events and even tells you the times that everything happens at. The thing is doesn't tell you is what triggered the wake event. It does give you a numerical code however. Here are some examples of what I am finding. Index : 2901 EntryType : Information InstanceId : 1 Message : The system has resumed from sleep. Sleep Time: 2010-10-01T23:20:06.097488100Z Wake Time: 2010-10-03T17:41:12.796400500Z Wake Source: 0 Category : (0) CategoryNumber : 0 Source : Microsoft-Windows-Power-Troubleshooter -- Index : 2841 EntryType : Information InstanceId : 1 Message : The system has resumed from sleep. Sleep Time: 2010-10-01T19:19:37.239789600Z Wake Time: 2010-10-01T21:28:48.921200800Z Wake Source: 4HID Keyboard Device Category : (0) CategoryNumber : 0 Source : Microsoft-Windows-Power-Troubleshooter So here's my question: Does anyone know what the different numerical codes for the "Wake Source" mean? I think "0" is a magic packet and "4" is a USB device. Does anyone have any idea if there is any documentation out there on this for Windows 7? Thanks in advance

  Read the article

• ESXi - change to thin - virtual disk filesize is the same

  - by sven

  running ESXi 5.5 here with a datastore on a single SSD. Now, I thought about changing to thin disks from thick and found that I could use a tool on the ESXi host to do that. However, the file size of the new created virtual disk is not changing. I run: vmkfstools -i loader.vmdk -d 'thin' thinloader.vmdk Destination disk format: VMFS thin-provisioned Cloning disk 'loader.vmdk'... Clone: 100% done. After that I compared the virtual disksizes: ls -la *.vmdk -rw------- 1 root root 32212254720 Jun 10 08:25 loader-flat.vmdk -rw------- 1 root root 467 May 21 17:04 loader.vmdk -rw------- 1 root root 32212254720 Jun 10 08:27 thinloader-flat.vmdk -rw------- 1 root root 520 Jun 10 08:33 thinloader.vmdk Stats on the original file: stat loader.vmdk File: loader.vmdk Size: 467 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 419443780 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-01-25 10:17:34.000000000 Modify: 2014-05-21 17:04:06.000000000 Change: 2014-05-21 17:04:06.000000000 and on the thin file: stat thinloader.vmdk File: thinloader.vmdk Size: 520 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 432026692 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-06-10 08:27:45.000000000 Modify: 2014-06-10 08:33:30.000000000 Change: 2014-06-10 08:33:30.000000000 Anyone an idea why the disk is not providing any more space (tried with multiple VM's already - all the same)? Also, I have noticed that the newly created file "autoappend" "-flat" to the disk ... Thanks Sven Update - diff of the vmdk config* --- loader.vmdk +++ thinloader.vmdk @@ -7,15 +7,17 @@ createType="vmfs" -RW 62914560 VMFS "loader-flat.vmdk" +RW 62914560 VMFS "thinloader-flat.vmdk" ddb.adapterType = "lsilogic" +ddb.deletable = "true" ddb.geometry.cylinders = "3916" ddb.geometry.heads = "255" ddb.geometry.sectors = "63" ddb.longContentID = "6d95855805dfa0079327dfee29b48dca" -ddb.uuid = "60 00 C2 98 d5 7d 17 bf-ac 54 70 b1 2d 39 43 d5" +ddb.thinProvisioned = "1" +ddb.uuid = "60 00 C2 93 c4 13 6c cf-bb 7b 34 c9 2c b4 dc 1e" ddb.virtualHWVersion = "8"

  Read the article

• Dual Monitor setup issues between laptop and external led monitor

  - by Julian

  I have two challenges. Monitor will not connect to laptop through HDMI Watching HD video content causes the laptop to sometimes turn off expecially when I'm streaming from tekzilla.com Setup. I got my new HP 2311x LED LCD monitor this week and I have it running as the main monitor extended by the 15 inch screen on my Dell Studio 1558. Right now I have to connect the external monitor through VGA. For the HDMI connection issue. I suspect that either the appropriate drivers are not installed because I don't see any hdmi device in the device manager. I've checked and I don't see any hdmi specific drivers listed online. For the shut down issue, I suspect the laptop might be overheating. Not sure why it would. It never did that while I watched movies on my laptop's default screen. My Laptop Configuration: 15" led lcd screen at 1366 x 768 intel i5 processor integrated graphics card 4 GB DDR3 RAM 500 GB hard drive I've tried everything from switching the source on my monitor to hdmi to start up combinations and nothing has worked. What could be the issue and how do I solve it?

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >