Search Results

Search found 8343 results on 334 pages for 'laptop disasters'.

Page 315/334 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• disable specific PCI device at boot

  - by Rhymoid

  I've just reinstalled Debian on my Sony VAIO laptop, and my dmesg and virtual consoles all get spammed with the same messages over and over again. [ 59.662381] hub 1-1:1.0: unable to enumerate USB device on port 2 [ 59.901732] usb 1-1.2: new high-speed USB device number 91 using ehci_hcd [ 59.917940] hub 1-1:1.0: unable to enumerate USB device on port 2 [ 60.157256] usb 1-1.2: new high-speed USB device number 92 using ehci_hcd I believe these messages are coming from an internally connected USB device, most likely the webcam (since that's the only thing that doesn't work). The only way I can seem to have it shut up (without killing my actually useful USB ports) is to disable one of the USB host controllers: # echo "0000:00:1a.0" > /sys/bus/pci/drivers/ehci_hcd/unbind This also takes down my Bluetooth interface, but I'm fine with that. I would like this setting to persist, so that I can painlessly use my virtual console again in case I need it. I want my operating system (Debian amd64) to never wake it up, but I don't know how to do this. I've tried to blacklist the module alias for the PCI device, but it seems to be ignored: $ cat /sys/bus/pci/devices/0000\:00\:1a.0/modalias pci:v00008086d00003B3Csv0000104Dsd00009071bc0Csc03i20 $ cat /etc/modprobe.d/blacklist blacklist pci:v00008086d00003B3Csv0000104Dsd00009071bc0Csc03i20 How do I ensure that this specific PCI device is never automatically activated, without disabling its driver altogether? -edit- The module was renamed recently, now the following works from userland: echo "0000:00:1a.0" > /sys/bus/pci/drivers/ehci-pci/unbind Still, I'm looking for a way to stop the kernel from binding that device in the first place.

  Read the article

• Installing Windows 8 to another computer with an OEM product Key

  - by user180671

  Questions come up after reading the article about the new method Microsoft uses to License windows 8 computers. Let say I bought a Brand new laptop with windows 8 preloaded. Not like the old way, there is no OEM sticker in the back of the computer which can be used for reloading system.(new product key is stored in BIOS as mentioned in the article, the key can be pulled out by using a software anyway). Is it possible to install windows 8 on another computer with that particular key in case the computer is totally damaged? Here is what i tried: First, I extracted the key with a software name "windows 8 key viewer". using the windows 8 upgrade tool to determine what copy of windows 8 I should download for the installation. The tool did correctly recognized the key as a legitimate one. but it claims that key can not be installed with a retail media (Since it is an oem key). Does this mean the only way to do it is to use an OEM CD from the manufacturer? Will ISO from MSDN source do? or it is just not possible??

  Read the article

• Remote Desktop connection to vista vs. xp

  - by CMP

  I am trying to log into my work computer remotely. I am using Windows 7 on my laptop. I have created a vpn connection to the network, and I am doing a remote desktop connection directly to the ip of my box (192.168.xxx.yyy). If I do a remote connection to a different box, running xp, it goes into remote desktop mode immediately and I see the windows login dialog as I am used to seeing. If I try remoting to my box, which is running vista, I do not see the remote desktop mode, but an additional dialog on my local machine asking for my credentials. It defaults in my local username. It allows me to log in as a different user, but the domain it has is still my local domain, not my work domain, so none of my usernames or passwords work. There doesn't appear to be a way to change the domain. Trying to hit several more boxes, it appears to act differently on xp and vista target machines. I feel like this must be a configuration issue, but I am not sure what the problem is. Any idea on how I can connect?

  Read the article

• How to stop my wireless adapter from received dhcp from router (windows)

  - by baobeiii

  Hi, I have a windows 7 computer which is connected via vpn to an OpenVpn server which happens to be in another country. I have all internet traffic being routed from my computer through the vpn to the server. However dns queries are not going through the vpn, but are instead going directly to my isp's dns via a route outside of the vpn tunnel. This is happening because my wireless adapter is configured to obtain DNS server address automatically. The router that stands between my computer and the internet happens to have a DCHP server running on it that is assinging my computer with the DNS addresses of the isp. The issue is, i haven't been able to stop my wireless adapter on my computer from receiving the dns settings from the router. I've tried selecting 'use the following dns server addresses' and then just leaving them blank, but ipconfig /all shows me that this hasn't worked and i'm still getting dns form the router. So is there any way to completely stop my windows wireless adapter from receiving these settings from the router? I have the OpenVpn server pushing to my computer's tun adapter the dns that it should be using. I'd rather solve this in a way that doesn't involve disabling the dhcp server on the router or fiddling with the router. The reason is i'm on a laptop and i want my vpn to not leak dns even when i'm out, for example in wireless hotspots. I know if i could just force the wireless adapter to ignore the router's dhcp server then my dns queries would go through the tunnel to the dns address pushed by the OpenVpn server. Sorry, i know thats long winded, if you have any idea's please do tell me. Thanks and merry xmas.

  Read the article

• Timestamp Updating Constantly on /dev/null

  - by motorleague

  I've been working on a problem with a /dev/null file on an AIX system (just for background it looks as though it was inadvertently deleted and recreated as a normal file by somebody), but in trying to determine what caused the problem, I noticed that the timestamp on it seems to update every minute. I've observed this on several AIX servers at my workplace. At present I can't entirely rule out this be something specific to the Application being used at my workplace, so I compared with CentOS and Debian based computers at home last night. The CentOS box, which runs 24 hours, had a mod time on /dev/null of around 4 days ago (during which time it was essentially just being used as a web browser and multimedia player, although it would have had active but essentially unused Apache, MySQL and VMM processes running in the background). The timestamp on /dev/null on the Debian machine, which was a just booted laptop, pretty much reflected the boot time, but I tested redirecting STDIN from, and STDOUT to it, and the modification time was unchanged (I'm not sure 100% sure if directing data to /dev/null constitutes "writing to it" in the way it would a normal file). So my question is essentially, could anybody please offer any advice with regards to what circumstances (permissions changes etc.. aside) might cause the timestamp on /dev/null to update? Thanks very much for any suggestions. Alex.

  Read the article

• Corsair SSD appears completely blank and does not retain written data

  - by ebanders

  I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

  Read the article

• Advice on cloning disk

  - by hks

  I'm going to buy a second disk for backup, the same size as my laptops. I want to mount it in a casing via usb and backup an entire hdd every soemtime. That's because I want the posibility to just switch drives in case of something goes wrong. I'm using Linux and obviously the right tool seems to be dd. The thing is that my laptop drive has a speed of around 50-70 MB/s and usb 2.0 is 57 MB/s. So to copy my 250GB disk should take me more than 1 hour if I'm lucky. I can't wait this much. I want some differential backup. I read one of JWZ articles. In it he gives more details for using rsync on Mac. He writes that there is possibility of making rsync'ed disk bootable. So my question is: how to make rsync'ed hdd bootable under Linux or are there other 'quick backup' tools for Linux that would allow me to just swap drives? Or should I just stick to dd :( ?

  Read the article

• Games on windows 8 in bootcamp lag even on lowest graphics

  - by Jackson Gariety

  I've been playing Crysis 2 and Skyrim on my Retina MacBookPro (10,1) for months now. The two games used to run super smoothly even on nearly maxed out settings. This laptop has an Nvidia GeForce GT 650M graphics card inside, it runs great. But I recently replaced my Windows 8 consumer preview with the retail copy, and since then, 3D games lag in this odd way, no matter what the graphics settings. Every second Skyrim and Crysis alternates between running smoothly and lagging. It's a cyclical lag that comes and goes like clockwork. I can turn the graphics down to 800x600 with no antialiasing and low texture quality, and it runs much smoother on the "up" motion of the cycle, but every second it moves back into this lag spike. I've tried installing beta graphics drivers, re installing the operating system, re installing the bootcamp support software, and freeing up space (I have about 20 GB free). I can't figure out what suddenly caused this other than some obscure difference between the consumer preview and the retail version. What can I try? Is my video card failing? Are there some other drivers I can install? This isn't normal lag from maxing out the card, it

  Read the article

• Win 7 64 with 8 gig of ram, getting running low on memory errors.

  - by John

  I have a new Dell laptop running Win7 64 with 8 meg of ram. If I leave the system running overnight I start getting low memory errors the next day. Looking at task manager it shows 6.27 gig used but looking at the processes list the totals don't show nearly that much. I am showing all processes from all users. I have also looked at the processes with PRocess Explorer and see the same results. Using resource monitor I see 4165 MB in Use, 2328 MB Modified and 1352MB Standby with only about 345 MB free. These numbers don't seem to add up to what I have running. I have Visual Studio 2010 running along with a number of IE8 sessions. I have run the same set of apps with XP SP2 32 bit with 4 gig of memory and never had this sort of problem. What is Modified memory? What is Standby memory? Any suggestions on what might be the issue and what might be a fix? TIA J

  Read the article

• How to tell Linux to explicitly swap out main memory of suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by user57019

  I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Windows Broken after Deletion of HP_TOOLS partition

  - by beanland

  When I decided to install Ubuntu on my laptop as a dual-boot, I recognized that Windows 7 was using four separate partitions. I (yes, this was stupid) thought the HP_TOOLS partition was probably one I could get rid of, so I deleted it and installed Ubuntu side-by-side Windows using the installation wizard, but now Windows won't progress past the loading screen without the computer automatically restarting. I've had to use Ubuntu exclusively since then. I'm not sure how I can recover it. All of my files seem to still be there--I can mount the other partition and see them, use them, etc--but Windows 7 won't boot. I really have no idea what to do or what to try, or even if I'm at a salvageable point. here's a screenshot of GParted: This makes me suspicious that it wasn't necessarily the removal of my HP_TOOLS partition but the "unknown" status of that 992.50 KiB partition there, sda1. I'm assuming that's the recovery one? How can I get Windows bootable again? I'm sorry, but I'm so unfamiliar with this sort of thing I'm not quite sure where to start.

  Read the article

• Windows 7 black screen after boot animation

  - by t_virus

  This is happening with my windows 7 64-bit install frequently. Today i was trying to install an icon pack. There was already a restore point prior to it so i didn't feel like create one. I replaced the following system files in both system32 and sysWOW64 imageres.dll imagesp1.dll zipfldr.dll and shell32.dll After a reboot i see windows boot animation and then a black screen (with no mouse) I let it like that for 10 minutes and the laptop automatically went to sleep mode. I wake it up and see an error box this error "interactive logon failed to initialize" I close it and i'm left with a black screen again, this time with a mouse though. I tried using automatic system repair. It just tells me to remove any extra hardware (i have none attached atm) System restore finishes successfully but doesn't fix the problem. Safe mode doesn't work either. same black screen after boot animation Can someone help me with this? Also, I'll be grateful anyone can upload those default files (listed above) for both system32 and sysWOW64 from a windows 7 64bit install (no service pack)

  Read the article

• Route outbound connections from local network through VPN

  - by Sharkos

  I have a server A running OpenVPN, an OpenVPN client B (a rooted Android phone as it happens) and a third party C (a laptop, tablet etc.) tethered to B. B can use the VPN to access the internet via A; C can use the tethered connection WITHOUT the VPN to access the internet via B. However, with the VPN on B active, I cannot load information from the internet on C. A appears to log similar traffic inbound and outbound when B or C attempt to load a webpage, say, but the VPN on device B reports no inbound traffic when the connection originated from C. Where should I look for packets being dropped, and what ip rules should I use to make sure they are passed back through the VPN and into the local network B <- C? (I'll obviously post whatever further information is needed.) Further info Without VPN: root@android:/ # ip route default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 With VPN: root@android:/ # ip route 0.0.0.0/1 dev tun0 scope link default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link [External address of A] dev tun0 scope link 128.0.0.0/1 dev tun0 scope link 172.16.0.0/24 dev tun0 scope link 172.16.0.8/30 dev tun0 proto kernel scope link src 172.16.0.10 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 192.168.168.0/24 dev tun0 scope link

  Read the article

• Low 'Burst Rate' from SATA drive in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

  Read the article

• Can only ssh when not using wifi

  - by AChrapko

  So I have 3 machines, a windows 7 desktop that is always wired to my router, osX laptop, and raspberry pi running debian linux. My router is a Linksys e1000 wireless N. My goal is to be able to ssh the raspi from any machine, while it is connected via wifi. My problem is that when trying to ssh from either the win7 or osX to the Pi it either times out, or gives an error: "ssh: connect to host 192.168.1.### port 22: No route to host" The only times that I have managed to connect to the pi from any machine were when it connected to the router via an Ethernet cable. Currently with win7 desktop wired, macbook wireless, and pi wireless tests give the following: win7 ping macbook: Destination host unreachable. macbook ping win7: Request timeout. win7 ping pi: Destination host unreachable. macbook ping pi: Request timeout. blah blah blah Plugging the macbook into the router with an Ethernet cable all communication between win7 and macbook works. Pings, ssh, ftp, smb ect... No changes to the pi, still no connections possible to or from any of the other 2 machines. Note All machines, are able to connect to the internet and ssh to the same machine on a completely different network, wired or over wifi. Plugging the Pi in with Ethernet (and macbook still wired) I can ssh to the pi from both win7 and macbook. I can ssh from the pi to macbook. All machines still able to connect the the off network machine. Also another little side note- I was playing warcraft 3 with my roommates the other day, and the only time they were able to see my LAN game was when they were plugged into the router with an Ethernet cable. Once or twice one of the laptops was able to connect over wifi, but not without another computer connecting first via Ethernet. So basically does anyone have any info as to why my router seems to completely ignore local wireless traffic?

  Read the article

• Confused with creating an ODBC connection, apparently I have two separate odbcad32.exe files?

  - by Hoser

  Alright, this is my first time working with this so forgive me if I'm a little confusing or vague. I have a server with Windows Server 2008 Standard without Hyper-v (6.0, Build 6002). I'm running a small website off this server and using a Microsoft Access database to store some information coming in through the website. I'm sure the PHP I have written to open the ODBC connection is correct as it has worked for me when I created this website in a testing environment on a laptop. My current issue now is that it seems like I have two different odbcad32.exe's, and one doesn't appear to have a driver for a .accdb file, and only a .mdb file. The other has a driver for both. The first one I speak of has a driver titled 'Driver do Microsoft Access (.mdb)', the second one has a driver titled 'Microsoft Access Driver (.mdb, .accdb)'. I access the first odbcad32.exe by going to C:\Windows\SysWOW64\odbcad32.exe, and then the one that seems to have the driver I need I go to Control Panel-Administrative Tools-Data Sources(ODBC) and simply create a new connection in the System DNS tab. Whenever I make changes to the one that I access through the Control Panel, I see no changes, however if I use the odbcad32.exe file in SysWOW64 I do get some changes in the errors that come back to me. The main difference I noticed is that when I set up an ODBC connection with the Control Panel method it said it simply couldn't find the ODBC connection, but when I made a .mdb connection in the SysWOW64 one (and pointed it to a .accdb file) it says Cannot open database '(unknown)'. It may not be a database that your application recognizes, or the file may be corrupt. Which makes it seem like it is this odbcad32.exe version in SySWOW64 that is being recognized as the 'correct' one. Is there any way to fix this? I've tried to be as thorough as possible but if I've been confusing or left anything out let me know.

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by Melot

  Hi! I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Recovering a broken NTFS filesystem?

  - by OverTheRainbow

  A much-needed Windows Update broke a Vista laptop that was running fine until then: After booting up, Windows displays "Please wait..." but it never goes anywhere. I waited for a couple of hours, there is a bit of disk activity, but it didn't work out in the end. I booted with the Vista DVD, chose "Repair your computer" which said that there was nothing wrong :-/ Next, I booted it up with a Linux USB keydrive, and ran Gparted 0.8.1 (which includes ntfsresize v2011.4.12AR.4 libntfs-3g) which displays a bunch of warnings for the NTFS partition where the Vista system is located such as: ntfs_mst_post_read_fixup: magic: 0x00000000 size: 1024 usa_ofs: 0 usa_count: 65535: Invalid argument Record 16 has no FILE magic (0x0) Next, I ran ntfsfix /dev/sda2, which said: Mounting volume... OK Processing of $MFT and $MFTMirr completed successfully. NTFS volume version is 3.1. NTFS partition /dev/sda2 was processed successfully. Next, I rebooted Vista, which did a CHKDSK, before rebooting. But I'm still getting nowhere with "Please wait..." Before I copy the user's data to another host and reinstall Vista from a DVD, does someone know what I could try? Thank you. Edit: In case someone else has the same issue... After the BIOS, hit F8 and choose "Repair your computer", followed by "Toshiba HDD Recovery". In addition to a 1,5GB partition labelled "WinRE", the hard disk contains a second partition labeled "Data" from which the application will fetch a system image and reinstall it in the "Vista" partition. Make sure you copy your data out of the system partition before doing this.

  Read the article

• Which Cardbus/PCMCIA -> USB card works with external hard drive?

  - by Carl

  I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

  Read the article

• how do i completely delete ask.com from my computer?

  - by celyn

  I have used Final Uninstaller (unregistered version) to remove it. So it removed the toolbar and the things in its folder from C:Program Files/Ask.com except for one thing; remaining are "Ask.com" folder > "Updater" folder > "Updater.exe" I have not checked my registry yet. But if there is something I want it to be gone! As to why I can't delete that updater thing, my laptop asks me permission (says need to be admin) whenever I tried to delete anything from ask.com folder, or its folder at all. I have googled, came to and followed the instructions from "Scott McClenning" in this post. Does not really work. When I say "not really", means, this error message pops up everytime I tried to do that: An error occurred applying attributes to the file: C:/Program Files/Ask.com Access is denied. How can I gain access? I AM the admin for this computer. And... don't ask me to download too many things for my computer, it adds to my frustration. Just in case you are wondering, I got this from FormatFactory when I updated it to 2.70. I should not have done so. Update: Now after I restarted my computer, I got the "EVERYONE" group in and it is under Full Control with every box ticked except for the last one (Special). When I tried to delete that folder and the .exe file, this keeps popping up as i click "try again", only goes away when I click "cancel"

  Read the article

• Mac Outlook showing all links in smart quotes?

  - by user2727128

  I was given the task of fixing my friend's email today and really don't know what the problem is. When an email is sent from his laptop (Mac) from Outlook the email address link in the signature shows exactly like this: [email protected]<mailto:[email protected]>. Additionally the website link displays like this: www.website.com<http://www.website.com>. And lastly, the image comes through as cid:randomstringofnumbers. When I sent him an email and he sent one back it converted my signature to same weird formatting. Plus, even in the header where it shows our emails, they are displaying the same way: [email protected]<mailto:[email protected]>. And the weirdest thing is that this problem seems to be "compounding". So when I scroll down to the last, most recent email in the thread I see this www.website.com<http://www.website.com> next email shows this: www.website.com<http://www.website.com><http://www.website.com> and the next this: www.website.com<http://www.website.com><http://www.website.com><http://www.website.com> This is happening to the emails too, everywhere. I'm thinking this might be something to do with smart quotes and the auto formatting but I'm not sure. Could this be the problem? And if so how do I fix it?

  Read the article

• UEFI boot options gone

  - by user1797930

  I ran into some issues booting Windows after trying to make a complete backup of the disc. After searching for information about some of the error codes, I found advise to change some BIOS settings, but instead I thought I would just "restore defaults" to make sure all settings were set as originally intended. After doing so, all UEFI boot options except for "Windows Boot Manager" are gone. That means, including the CD/DVD drive, so I cannot even boot from a recovery DVD anymore - and as explained, Windows is not able to boot either. Do you have any advice? When I added a secondary drive originally, it was automatically added to the boot options menu. Even when removing and re-adding the drive physically, the option does not appear again. I have tried unplugging power, and hold down start button for 10 seconds, and boot afterwards - no change. It's a laptop so removing CMOS battery is not an option. I have read information that it is an issue with data removed from NVRAM, but I am unable to find a way to recover it. "Add new boot options" requires a path - but the CD/DVD was originally available without any CD's in the drive - so there is no path available to add the drive. I did try to open EFI shell, but it seems not to be embedded in the UEFI/BIOS. It just says "not found". I'm really lost here - any advice is appreciated.

  Read the article

• Using a second Wifi Router (in order to use a LAN port)

  - by Sledge81

  Problem: Connecting a TV decoder via Internet. It doesn't have inbuilt wifi so wired LAN is the only option. I bought a second Wifi Router so I could use its LAN port to create a wired internet connection to my decoder. What I want to achieve: The second Wifi Router should basically pick up the signal from the main wifi router. I would then use the LAN port to connect (with a wire) to the TV decoder. In other words have my secondary Wifi Router act as an access point, which will enable me to use a wired LAN connection to the decoder. What i've done so far: Connected the second Wifi Router to my laptop via the LAN ports. Access 192.168.1.1 and went into my second router. 1) SSID set to the same one as the main Wifi Router 2) Tried disabling DHCP and enabling DHCP (with the DNS and default gateway configured the same as the main router). When I check my network connections, I see the LAN connection too but it says 'Not connected to the internet' while the Wifi (main router) shows connected. Can someone please advise on how to use my second Wifi Router to connect to the main Wifi Router (and thus the Internet). Thanks. main wifi router: Zyxel secondary wifi router: TP Link

  Read the article

• Windows 8 Communication Sound Setting not working

  - by blackmastiff

  I've been having a problem on my new laptop recently which is familiar but baffling the usual fixes. I'm running Windows 8 with an onboard Realtek soundcard. It's similar to the one on my older computer running Windows 7. The problem is, when I'm in Skype or Mumble, Windows changes the sound output to lower everything else automatically. I've disabled the communications sound change option on the communications tab within sound devices and checked all the applications settings to insure that they are not responsible. They aren't, and I noticed something else. When I'm in the sound properties dialog, and I switch to the microphone tab, the same audio output reduction occurs. This seems to say to me that the microphone must be responsible in some way, but seeing as I uninstalled all the drivers and installed windows drivers instead, I'm confused as to why this would be occurring. Any thoughts? EDIT: I just tried disabling the built in microphone and the sound no longer get changed. More confused now? As soon as I turn it back on, the sound gets dropped again. Incidentally, the fix for this on windows 7 was this question: Windows 7 lowers applications' volume automatically I've got my computer set that way and it doesn't work.

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >