Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 315/433 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• Unable to enable wireless in ubuntu 12.04

  - by Joe

  I have a Vostro 2520 and not sure how to enable wireless on my machine. The details are given below, would appreciate any pointers to resolving this issue. lsmod returns Module Size Used by ath9k 132390 0 ath9k_common 14053 1 ath9k ath9k_hw 411151 2 ath9k,ath9k_common ath 24067 3 ath9k,ath9k_common,ath9k_hw b43 365785 0 mac80211 506816 2 ath9k,b43 cfg80211 205544 4 ath9k,ath,b43,mac80211 bcma 26696 1 b43 ssb 52752 1 b43 ndiswrapper 282628 0 ums_realtek 18248 0 usb_storage 49198 1 ums_realtek uas 18180 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_cirrus 24002 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep psmouse 97362 0 dell_wmi 12681 0 sparse_keymap 13890 1 dell_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq wmi 19256 1 dell_wmi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device mac_hid 13253 0 i915 473240 3 drm_kms_helper 46978 1 i915 uvcvideo 72627 0 drm 242038 4 i915,drm_kms_helper videodev 98259 1 uvcvideo soundcore 15091 1 snd dell_laptop 18119 0 dcdbas 14490 1 dell_laptop i2c_algo_bit 13423 1 i915 v4l2_compat_ioctl32 17128 1 videodev snd_page_alloc 18529 2 snd_hda_intel,snd_pcm video 19596 1 i915 serio_raw 13211 0 mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 sudo lshw -class network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7c00000-f7c07fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 07 serial: 78:45:c4:a3:aa:65 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.5 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes

  Read the article

• ubuntu 11.10 can't find wireless after waking from sleep

  - by Colleen

  I've tried a lot of proposed solutions, most of them adding files to /etc/pm/config.d, as well as WiFi stops working after waking from suspend and nothing has worked. hardware info: [colleen@colleen-HP ~]$ sudo lshw -C network [sudo] password for colleen: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:b1:ea:67 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:4000(size=256) memory:c1404000-c1404fff memory:c1400000-c1403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 8c:a9:82:99:48:8c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-21-generic-pae firmware=39.31.5.1 build 35138 ip=192.168.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:c5500000-c5501fff Is anyone else still having this problem? The two solutions I haven't tried are installing wicd and upgrading because I've heard both are kind of unstable/buggy and wicd frankly scares me.

  Read the article

• Dual displays not working - NVidia - Ubuntu 12.04 - Second Monitor - Two Screens

  - by user75105

  Graphics Card: NVidia 460 GTX. Driver: NVIDIA accelerated graphics driver (version current) I have one DVI monitor, an old Dell LCD from 2005, and one VGA monitor, an Asus ML238H from 2010 whose HDMI port broke. The Asus is plugged into my graphics card's primary monitor slot and is the better monitor even though it is VGA but my computer defaults to the Dell. This happens when I boot as well; the loading screens, the motherboard brand image, etc. are all displayed on the Dell monitor until Windows loads. Then both monitors work. The same thing happened when I booted up Ubuntu 12.04 but I did not see the second monitor when the log-in screen popped up, nor did I when I logged in. I went to System Settings/Displays and my Asus monitor is not an option. I clicked Detect Displays and the Asus is not detected. I looked at the other questions regarding NVIDIA drivers and recalled my problems with Ubuntu a few years ago and decided to check the driver. I went to Additional Drivers to install the proprietary driver and it looks like it's installed and active but I'm still having this problem. There is another driver option, the post-release NVIDIA driver, but that does not fix the problem either. Also, under System Details/Graphics the graphics device is listed as Unknown, which might indicate that it is using an open source generic driver and not the proprietary NVidia driver. But under Additional Drivers it says that I am using the NVidia driver. Any help is appreciated.

  Read the article

• Dynamic Monitoring Service (DMS) Configuration Dumping and CPU Utilization

  - by ShawnBailey

  There was recently a report of CPU spikes on a system that were occuring at precise 3 hour intervals. Research revealed that the spikes were the result of the Dynamic Monitoring Service generating a metrics dump and writing it under the server 'logs' folder for every WLS server in the domain. This blog provides some information on what this is for and how to control it. The Dynamic Monitoring Service is a facility in FMw (JRF to be more precise) that collects runtime data on the components deployed to WebLogic. Each component is responsible for how much or how little they use the service and SOA collects a fair amount of information. To view what is collected on any running server you can use the following URL, http://host:port/dms/Spy and login with admin credentials. DMS is essentially always running and collecting this information in the runtime and to protect against loss of this data it also runs automatic backups, by default at the 3 hour interval mentioned above. Most of the management options for DMS are exposed through WLST but these settings are not so we must open the dms_config.xml file which can be found in DOMAIN_HOME/config/fmwconfig/servers/<server_name>/dms_config.xml. The contents are fairly short and at the bottom you will find the following entry: <dumpConfiguration>     <dump intervalSeconds="10800" maxSizeMBytes="75" enabled="true"/> </dumpConfiguration> The interval of 10800 seconds corresponds to the 3 hours and the maximum size is 75MB. The file is written as an archive to DOMAIN_HOME/servers/<server_name>/logs/metrics. This archive contains the dump in XML format. You can disable the dumps all together by simply setting the 'enabled' value to 'false' or of course you could modify the other parameters to suit your needs. Disabling the dumps will NOT impact DMS collections or display at runtime. It will only eliminate these periodic backups.

  Read the article

• CLR Profiler Allocated Bytes and XNA ContentManager

  - by Vackup

  I've been fighting with XNA ContentManager and memory allocations for some weeks because I'm trying to port my game from XNA (Windows) to ExEn / Monotouch (iphone). The problem is that after playing a few levels, my game exits unexpectedly on a real iPhone device (not simulator). Profiling memory usage on Windows with CLRProfile, I found some useful stuff but I also found something I dont understand. If I use 2 ContentManagers (1 for shared assets and 1 for level assets), when profiling, "Allocated Bytes" grows and grows after level through level but Memory consumption measured by Windows Task Manager stays constant (down when I unload the content manager and up again when I load content). Obviously, I contentManager.Unload() when level ends. After a few levels my game exits unexpectedly on an iPhone device. If I use 1 content manager, "CRLProfiler Allocated Bytes" stays constant on Windows and on the iPhone; I can play the game normally and it doesnt exit unexpectedly. I use the same assets level through level. It seems like in ios (iPhone) when loading and unloading the same assets, it allocates memory and consumes all device memory, so the ios kill it. Can anybody explain me how this really works? I've read quite a bit, but I still don't understand what's going on.

  Read the article

• ATI HD5450 w/ Ubuntu 14?

  - by Oliwb

  So, I'm running Ubuntu 12.04 right now. Last night I realised that I'm way behind as we're up to 14! Decided to run the updater and figured I'd take the path of least resistance (but lengthy choice) of going 12.04 - 12.10 - 13.xx - 14.xx. So I download the first packet and then get an error message about my graphics card perhaps not working in 12.10. Now part of the reason I was looking to upgrade is because I get (and have always had) this strange occasional flickering - now that I have two screens it's just on the second monitor.....oddly this is not the same port that was giving issues before). The graphics card is an ATI Radeon HD5450 and I have the Catalyst (I think it's 13 or 14) driver installed - last night. It could be that the graphics card has never worked properly...I bought the PC new and with an "upgraded" video card and it's always suffered with this flicker. I just figured that the drivers weren't right or something. So I have 3 questions: 1) is my video card broken or is the driver letting it down and causing the flicker? 2) will it be able to handle the upgrade to 14 via 13? Or should I cut my losses and get something newer? 3) if I should get something newer....what should I get ( Thanks in advance....

  Read the article

• Kubuntu never gets to the login screen

  - by searchfgold6789

  I am not sure if Xorg is using the right device... The system in question is an A4-1400 CPU with built-in Radeon Graphics. I added a PCIe Radeon HD 5750, and changed the BIOS so it would use that card automatically. Now it appears that I can see output from the TV plugged into the HDMI port, and boot into recovery mode, but cannot get to a desktop - X doesn't start. It just freezes at the Kubuntu splash screen. I have no idea how to get X to use the proper graphics card. I pasted the Xorg.log to http://paste.ubuntu.com/6261137/. And the Xorg.conf generated by aticonfig --initial is at http://paste.ubuntu.com/6261161/ Also, see lspci and lshw -c display outputs. I can provide more information, but something does tell me X is not using the right graphics card and I've no idea where to begin how to fix it... I faced a similar issue before with another distribution but found no information anywhere on how to make X use a specific graphics card. Or maybe it's not that simple.

  Read the article

• New Nokia SDK 2.0 for Java (beta)

  - by Tori Wieldt

  Nokia recently launched the Asha 305, 306, and 311, which are full touch devices with smartphone-like functionality at a low price. This makes them particularly attractive to consumers in the developing and developed world who may not be able to afford a smartphone but have a strong demand for apps and the smartphone experience. The Asha phones are the latest addition to Nokia's Series 40 platform, all of which support Java ME. The SDK includes new Full Touch API's (e.g. supporting pinch zoom) and Sensor support delivering an enhanced App experience. It also adds improved Maps API support for creating socio-local apps. There are a number of improvements in the tools including the Nokia IDE for Java ME with in-build Device-SDK Manager. Many code examples, training videos, webinars and sample code will help get you started. Porting guides and sample code show you how to port your android app to Java ME. If you don't have access to the hardware you can use Remote Device Access to test on real hardware that's remotely hosted for free. You can also find Light Weight UI Toolkit (LWUIT) support, which can speed development significantly. Both In-App Advertising and In-App Purchase (beta) is supported. Here's a great revenue-making opportunity for developers and a great way of reaching a new app-hungry mass-market audience. Download the new Nokia SDK 2.0 for Java (Beta) and get developing! 

  Read the article

• Accidentally Changed Dual Monitor Setup and don't know how to reset it

  - by user203783

  I have a dual monitor setup with my laptop and an external Asus monitor running under Ubuntu 11.10. When I first started using Ubuntu, it synced both screens. What showed up on my laptop showed up on my eternal monitor. Last night, I accidentally knocked the HDMI cable from its port (not that unusual in the tight space I work in). When I plugged it back in, as usual, the external monitor only displayed my wallpaper. Usually, I just restart Ubuntu and it resets, but last night what I now realize was the display console came up and somehow I changed the setup. Now the two screens show different jobs so to speak. Also, the external monitor doesn't display the ribbon, making switching between Firefox tabs and windows or apps jarring. I write for a living and need to quickly check bits of research, notes or sources while writing and the extra switching between mouse pad and external mouse to get one or the other screen to respond interrupts my work flow. The only technical help I can offer is when the display console popped up, the graphical representation of the screens was that the external screen appeared layered over by about one-quarter of the laptop screen. Again, these were icons. I tried to replicate that after I obviously screwed things up. If someone could help. I would appreciate it. If I have to use terminal, that's fine. I started using computers for writing back when they were green DOS prompts. There's a certain elegance to prompt commands to me. Maybe it's the writer in me. Again, if anyone can help me return my screens to sync under Ubuntu 11.10, I would greatly appreciate it.

  Read the article

• Simple (and fast) dices physics

  - by Markus von Broady

  I'm programming a throw of 5 dices in Actionscript 3 + AwayPhysics (BulletPhysics port). I had a lot of fun tweaking frictions, masses etc. and in the end I found best results with more physics ticks per frame. Currently I use 10 ticks per frame (1/60 s) and it's OK, though I see a difference in plus for 20 ticks. Even though it's only 5 cubes (dices) in a box (or a floor with 3 walls really) I can't simulate 20 ticks in a frame and keep FPS at 60 on a medium-aged PC. That's why I decided to precompute frames for animation, finishing it in around 1700 ticks in 2 seconds. The flash player is freezed for these 2 seconds, and I'm afraid that this result will be more of a 5 seconds or even more, if I'll simulate multi-threading and compute frames in background of some other heavy processes and CPU drawing (dices is only a part of this game). Because I want both players to see dices roll in same way, I can't compute physics when having free resources, and build a buffer for at least one throw of each type (where type is number of dices thrown). I'm afraid players will see a "preparing dices........." message too often and for too long. I think the only solution to this problem is replacing PhysicsEngine with something simpler, or creating own physicsEngine. Do You have any formulas for cube-cube and cube-wall collision detection, and for calculating how their angular and linear velocities should change after a collision occurs?

  Read the article

• Ubuntu Wireless not working on Lenovo t400

  - by VmaxBoss

  This problem started after upgrading to 12.04, an my system is 'up2date' Have tried most of the solution-proposals found on the net. lspci -nnk | grep -iA2 net 00:19.0 Ethernet controller [0200]: Intel Corporation 82567LF Gigabit Network Connection [8086:10bf] (rev 03) Subsystem: Lenovo Device [17aa:20ee] Kernel driver in use: e1000e 03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlagn iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off sudo lshw -C network *-network description: Ethernet interface product: 82567LF Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:22:68:1a:c4:75 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.0.2-k2 duplex=full firmware=1.8-3 ip=192.168.2.154 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:29 memory:fc000000-fc01ffff memory:fc024000-fc024fff ioport:1820(size=32) *-network DISABLED description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:6c:2d:24 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:30 memory:f4300000-f4301fff Please help Br/VB

  Read the article

• problems establishing ssh connection

  - by Superbyte

  since two days I am facing a really weird problem. I have receantly installed ubuntu server 14.04 LTS on a workstation. It has a fix IP address, which I can successfully ping from other computers in the network. But when I try to establish a ssh connection from a windows computer via putty I get some strange errors, which I cannot fix. The Problem is that putty takes a really long time trying to establish a connection. After about 10 seconds I get the following error: Network error: Software caused connection abort But when I click the Restart Session option a several times after putty shows the error message, I can login in. But now comes the other problem. When the login appears on the putty console I type in the user, but it really takes a long time until I can type in the password to login. This is what I already tried: sshd: ALL in etc/hosts.allow commented line session optional pam_motd.so in etc/pam.d/login and etc/pam.d/sshd configured the firewall with: sudo iptables -A INPUT -p tcp --dport ssh -j ACCEPT checked if ssh server is listening on port 22 UseDNS no in etc/ssh/sshd_config I hope someone can help me, because this problem is really annoying. Thanks in regard

  Read the article

• Dual displays not working - NVidia - Ubuntu 12.4

  - by user75105

  Graphics Card: NVidia 460 GTX. Driver: NVIDIA accelerated graphics driver (version current) I have one DVI monitor, an old Dell LCD from 2005, and one VGA monitor, an Asus ML238H from 2010 whose HDMI port broke. The Asus is plugged into my graphics card's primary monitor slot and is the better monitor even though it is VGA but my computer defaults to the Dell. This happens when I boot as well; the loading screens, the motherboard brand image, etc. are all displayed on the Dell monitor until Windows loads. Then both monitors work. The same thing happened when I booted up Ubuntu 12.4 but I did not see the second monitor when the log-in screen popped up, nor did I when I logged in. I went to System Settings/Displays and my Asus monitor is not an option. I clicked Detect Displays and the Asus is not detected. I looked at the other questions regarding NVIDIA drivers and recalled my problems with Ubuntu a few years ago and decided to check the driver. I went to Additional Drivers to install the proprietary driver and it looks like it's installed and active but I'm still having this problem. There is another driver option, the post-release NVIDIA driver, but that does not fix the problem either. Also, under System Details/Graphics the graphics device is listed as Unknown, which might indicate that it is using an open source generic driver and not the proprietary NVidia driver. But under Additional Drivers it says that I am using the NVidia driver. Any help is appreciated.

  Read the article

• Why is text on my TV monitor all grainy?

  - by searchfgold6789

  I have successfully installed the Catalyst drivers and hooked up my 1080p TV to the Radeon HD 5750's HDMI port and now it is working. There only seems to be one issue - most images appear OK, at least to my eyes, but text is grainy and difficult to read (not sure how well it can be seen in the picture): It works fine with a smaller screen, and hopefully you can see it with the new pictures which are only slightly better, but images are rendered a little funny too. Changing antialiasing does nothing and changing the refresh rate only makes a slight change if any. The small monitor I have works fine. Smaller resolutions such as 1024x768 look OK but are the wrong aspect ratio. I have tried renaming the input mode on the TV to "PC", and that helped... a little bit. Also, I tried a different PC with the same result. Messing around extensively with the ATI Catalyst Control Center also did not help. I am wondering if there is anything else I can try to increase the quality so it is more usable.

  Read the article

• How to leverage the internal HTTP endpoint available on Azure web roles?

  - by adelsors

  Imagine you have a Web application using an in-memory collection that changes occasionally, loading it from storage on the Application_Start global.asax event and updating it whenever it changes. If you want to deploy this application on Azure you need to keep in mind that more than one instance of the application can be running at any time and therefore you need to provide some mechanism to keep all instances informed with the latest changes. Because that the communication through internal endpoints between Azure role instances is at no cost, a good solution can be maintaining the information on Azure Storage Tables, reading its contents on the Application_Start event and populating its changes to all instances using the internal HTTP port available on Azure Web Roles. You need to follow these steps to leverage the internal HTTP endpoint available on Azure web roles: 1.   Define an internal HTTP endpoint in the Web Role properties, for example InternalHttpEndpoint   2.   Add a new WCF service to the Web Role, for example NotificationServices.svc 3.   Add a method on the new service to receive notifications from other role instances. 4.   Declare a class that inherits from System.ServiceModel.Activation.ServiceHostFactory and override the method CreateServiceHost to host the internal endpoint.   Note that you can use SecurityMode.None because the internal endpoint is private to the instances of the service, this is provided by the platform. 5.   Edit the markup of the service right clicking the svc file and selecting "View markup" to add the new factory as the factory to be used to create the service    6. Now you can notify changes to other instances using this code:

  Read the article

• Help with Abstract Factory Pattern

  - by brazc0re

  I need help with a abstract factory pattern design. This question is a continuation of: Design help with parallel process I am really confused where I should be initializing all of the settings for each type of medium (ex: RS232, TCP/IP, etc). Attached is the drawing on how I am setting up the pattern: As shown, when a medium is created, each medium imposes a ICreateMedium interface. I would assume that the Create() method also create the proper object, such as SerialPort serialPort = new SerialPort("COM1", baud); however, TCPIPMedium would have an issue with the interface because it wouldn't need to initialize a serial port object. I know I am doing something majorly wrong here. I just can't figure it out and have been stuck for a while. What I also get confused on show the interface IMedium will get access to the communication object once it is created so it can write out the appropriate byte[] packet. Any guidance would be greatly appreciated. My main goal is to have the Communicator class spit a packet out without caring which type of medium is active.

  Read the article

• Is this JS code a good way for defining class with private methods?

  - by tigrou

  I was recently browsing a open source JavaScript project. The project is a straight port from another project in C language. It mostly use static methods, packed together in classes. Most classes are implemented using this pattern : Foo = (function () { var privateField = "bar"; var publicField = "bar";     function publicMethod() { console.log('this is public');     } function privateMethod() { console.log('this is private'); } return {   publicMethod : publicMethod, publicField : publicField }; })(); This was the first time I saw private methods implemented that way. I perfectly understand how it works, using a anonymous method. Here is my question : is this pattern a good practice ? What are the actual limitations or caveats ? Usually i declare my JavaScript classes like that : Foo = new function () { var privateField = "test"; this.publicField = "test";     this.publicMethod = function()     { console.log('this method is public'); privateMethod();     } function privateMethod() { console.log('this method is private'); } }; Other than syntax, is there any difference with the pattern show above ?

  Read the article

• Wireless does not work 12.10

  - by superkoop

  My primary issue is that my wireless does not work after I installed 12.10. The output to rfkill list all: 5: hci0: Bluetooth Soft blocked: no Hard blocked: no The output to lshw -class network is: *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 12 serial: 00:21:9b:d6:46:51 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:fe8fc000-fe8fffff ioport:de00(size=256) *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:17 memory:fe7fc000-fe7fffff The output to lspci -nn for the pertinent information is: 0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Thus, it seems the solution would be to run: sudo apt-get install linux-headers-generic sudo apt-get install --reinstall bcmwl-kernel-source sudo modprobe wl However, I do not currently have access to an ethernet connection, as I am currently only able to use verizon wireless 3g internet. Thus, is there a way to set up ICS with a Vista machine so that I can access the internet by using the Vista machine as the host? Or, is it possible to fix this by downloading the important packages in vista and moving them to ubuntu via USB drive?

  Read the article

• After upgrade to 12.04 wireless keeps dropping on BCM4312

  - by Sheket

  I know there are plenty of questions very similar to these, but I've tried practically everything and it still isn't working. Some solutions get the wireless connection working, but it goes very slow and drops after a few minutes. Then it won't reconnect and keeps asking for password. Hope you can help me. Thanks in advance. This is the output for sudo lshw -C network *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:f0300000-f0303fff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: c0 serial: 00:23:5a:9b:6e:b1 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:42 memory:f0200000-f023ffff ioport:a000(size=128) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:24:2c:83:f0:81 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-30-generic firmware=478.104 link=no multicast=yes wireless=IEEE 802.11bg And for lsmod | grep b43 b43 342643 0 mac80211 436455 1 b43 cfg80211 178679 2 b43,mac80211 bcma 25651 1 b43 ssb 50691 1 b43 And for rfkill list 5: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Extended service set help [closed]

  - by Cygnus X

  Sorry, this is going to be long and rambly. So, at home my network is set up as such: I have a "master router" that handles DHCP, from there I have a basic 5 port switch, and coming off that, I have a second router that I put in access point mode so that I could have better wireless coverage in my house. I cant seem to access it through a web browser since the master router kicked in and assigned it an ip address. But, i told you all that story, so that i could tell you this story. At the company I work for, they are trying to set up wireless cameras, according to the manual for these, in order to connect these cameras to our network, we need to get into the wireless router and associate the router with the cameras, but the problem is, the network is setup like my home network. Theres a "master router" which is a windows 2003 server, and then a wireless router in AP mode dishing out wireless access. I cant get into the router (by the way I'm not the system admin for the company, nor do i know jack squat about windows server , nor can I easily get in contact with the system admin. (quite the cluster f*k, eh?)) I've tried using wireshark to find the routers ip, dug through arp tables, tried plugging straight into the router, but I cant seem to get into the damn thing. Any ideas/suggestions would be greatly appreciated.

  Read the article

• No WIFI on Ubuntu 12.04 LTS after today software update

  - by Adchara

  I just got new dell inspiron3537 with Ubuntu 12.04 LTS (no windows O/S). It got some wireless (hard block) yesterday. So, this morning, I ran the software update all the security update. After that I can't see "Wireless" in system setting. So, I updated all the software update and looked thru several web site and found "sudo lshw -c network" command. I tried and found the result below. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: 74:86:7a:40:5d:48 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.10 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:60 ioport:4000(size=256) memory:c0700000-c0700fff memory:c0400000-c0403fff *-network UNCLAIMED description: Network controller product: QCA9565 / AR9565 Wireless Network Adapter vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0600000-c067ffff memory:9fb00000-9fb0ffff Please suggest what I should do to fix it. Thx in advance

  Read the article

• How to get the level and position of the player from an extern program? [on hold]

  - by user3727174

  I want to write a program that needs the current level and position of the player (primary single player). This should work for potentially every game installed and running on the computer my program is running on. The data I need is basically one integer value for the level (if there are any) and three integer values for x, y and optimal z for the position of the player. In which relation/scale or where the null point is does not matter, because this information is going to be interpreted game dependent, I will use this information to read information out of a database created for the game currently running. Currently I'm using C++, but if there is a better option for Java I´m willing to port my program. My thoughs so far are: make a mod for every game that should be supported, get the position/level from there, write this information to the disk and read it from my program tracking mouse/keyboard events and reconstructing the movement won't work Are there any general APIs for something like this? Any Tool to find this data? Or maybe engines that provide APIs to get this data directly from the game?

  Read the article

• how to speed up this code? [migrated]

  - by dot

  I have some code that's taking over 3 seconds to complete. I'm just wondering if there's a faster way to do this. I have a string with anywhere from 10 to 70 rows of data. I break it up into an array and then loop through the array to find specific patterns. $this->_data = str_replace(chr(27)," ",$this->_data,$count);//strip out esc character $this->_data = explode("\r\n", $this->_data); $detailsArray = array(); foreach ($this->_data as $details) { $pattern = '/(\s+)([0-9a-z]*)(\s+)(100\/1000T|10|1000SX|\s+)(\s*)(\|)(\s+)(\w+)(\s+)(\w+)(\s+)(\w+)(\s+)(1000FDx|10HDx|100HDx|10FDx|100FDx|\s+)(\s*)(\w+)(\s*)(\w+|\s+)(\s*)(0)/i'; if (preg_match($pattern, $details, $matches)) { array_push($detailsArray, array( 'Port' => $matches[2], 'Type' => $matches[4], 'Alert' => $matches[8], 'Enabled' => $matches[10], 'Status' => $matches[12], 'Mode' => $matches[14], 'MDIMode' => $matches[16], 'FlowCtrl' => $matches[18], 'BcastLimit' => $matches[20])); }//end if }//end for $this->_data = $detailsArray; Just wondering if you think there's a way to make it more efficient. Thanks.

  Read the article

• How would I broadcast a subdomain/virtual name on a local server with people connected to the same network

  - by Sarmen B.

  I have a server connected to the router which has ubuntu 12.04. It is has apache/mysql/php all installed ready to go. the folder structure is like this: /var/www -- this isnt the root -/libs -/logs -/public - this is the root -/vhosts - all subdomains go here I have a folder in vhosts named mysite. I went into /etc/apache2/sites-available and created a file and here are the contents - (vhost file). and I also added an entry in /etc/hosts file containing: 127.0.1.1 mysite.dev and I also did sudo a2ensite mysite i tried accessing the site from a computer via mysite.dev and our public ip into the server but i was not able to view it. the public directory in the structure above does display on all computers when i try our public ip. but for anything added in vhosts the site wont show. there is no domain attached its just our ip. I tried changing the port from 80 to say 9999 in the mysite file in sites-available and tried myip:9999 but that didnt work either. what am I doing wrong? edit: i forgot to mention that the server is dmzed on the router.

  Read the article

• Curl, twitter oauth problem

  - by Darxval

  Does anyone see a problem with the following Curl call / how the Oauth request is built? (i am trying to get a correctly setup request so i can finish my app) So i am calling the following CURL call: C:\>curl -v -k --data-urlencode "status=Testing2" -H "Authorization: OAuth realm='', oauth_nonce=1276107867blah, oauth_timestamp=1276107867, oauth_consumer_key=yJDLH7BDdVi1OKIINSV7Q, oauth_signature_method=HMAC-SHA1, oauth_version=1.0, oauth_signature=NWU4MDdlNjk0OGIxYWQ1YTkyNmU5YjU1NGYyOTczMmU5ZDg5 YWNkNA==, staus=Testing2 " http://twitter.com/statuses/update.xml?status=Testing2 and i recieve this: * About to connect() to twitter.com port 80 (#0) * Trying 168.143.162.68... connected * Connected to twitter.com (168.143.162.68) port 80 (#0) > POST /statuses/update.xml?status=Testing2 HTTP/1.1 > User-Agent: curl/7.20.1 (i386-pc-win32) libcurl/7.20.1 OpenSSL/0.9.8n zlib/1.2.5 libidn/1.18 libssh2/1.2.5 > Host: twitter.com > Accept: */* > Authorization: OAuth realm='', oauth_nonce=1276106370blah, oauth_timestamp=1276106370, oauth_consumer_key=yJDLH7BDdVi1OKIINSV7Q, oauth_signature_method=HMAC-SHA1, oauth_version=1.0, oauth_signature=MjQzNDA1MGU4NGRmMWVjMzUwZmQ4YzE5NzMzY2I1ZDJlOTRkNmQ2Zg==, staus=Testing2 > Content-Length: 15 > Content-Type: application/x-www-form-urlencoded > < HTTP/1.1 401 Unauthorized < Date: Wed, 09 Jun 2010 18:00:22 GMT < Server: hi < Status: 401 Unauthorized < WWW-Authenticate: Basic realm="Twitter API" < X-Runtime: 0.00548 < Content-Type: application/xml; charset=utf-8 < Content-Length: 164 < Cache-Control: no-cache, max-age=1800 < Set-Cookie: k=209.234.229.21.1276106420885412; path=/; expires=Wed, 16-Jun-10 18:00:20 GMT; domain=.twitter.com < Set-Cookie: guest_id=127610642214871948; path=/; expires=Fri, 09 Jul 2010 18:00:22 GMT < Set-Cookie: _twitter_sess=BAh7CDoPY3JlYXRlZF9hdGwrCIm33h0pAToHaWQiJTkyMjllODE0NTdiYWE1%250AMWU1MzBmNjgwMTFiMDhkYjdlIgpmbGFzaElDOidBY3Rpb25Db250cm9sbGVy%250AOjpGbGFzaDo6Rmxhc2hIYXNoewAGOgpAdXNlZHsA--8ebb3c62d461d28f8fda7b8adab642af66969f7e; domain=.twitter.com; path=/ < Expires: Wed, 09 Jun 2010 18:30:20 GMT < Vary: Accept-Encoding < Connection: close < <?xml version="1.0" encoding="UTF-8"?> <hash> <request>/statuses/update.xml?status=Testing2</request> <error>Could not authenticate with OAuth.</error> </hash> * Closing connection #0 my Parameters are setup like so: var parameters = [encodeURIComponent("status="+status),encodeURIComponent("oauth_token="+ac_token),encodeURIComponent("oauth_consumer_key="+"yJDLH7BDdVi1OKIINSV7Q"),encodeURIComponent("oauth_nonce="+nonce,"oauth_signature_method=HMAC-SHA1"),encodeURIComponent("oauth_timestamp="+timestamp),encodeURIComponent("oauth_version=1.0")] var join = parameters.join("&"); var eparamjoin =encodeURIComponent(join); The key is like so: var key=con_secret+"&"+ac_secret; Signature base string is: var signaturebs = "POST&"+encodeURIComponent(url)+"&"+eparamjoin; giving this: POST&http%3A%2F%2Ftwitter.com%2Fstatuses%2Fupdate.xml&status%253DTesting2%26oauth_token%253D142715285-yi2ch324S3zfyKyJby6WDUZOhCsiQuKNUtc3nAGe%26oauth_consumer_key%253DyJDLH7BDdVi1OKIINSV7Q%26oauth_nonce%253D1276107867blah%26oauth_timestamp%253D1276107867%26oauth_version%253D1.0 and signature built like so: var hmac = Crypto.HMAC(Crypto.SHA1, signaturebs,key ); var signature=Base64.encode(hmac); making the signature: NWU4MDdlNjk0OGIxYWQ1YTkyNmU5YjU1NGYyOTczMmU5ZDg5YWNkNA== Any help would be appreciated thank you!

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >