Search Results

Search found 9730 results on 390 pages for 'restart programs'.

Page 316/390 | < Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >

• Windows 7 BSOD on startup

  - by Cristy

  I got a BSOD today after getting home from 11 hours of work... It seems to work in SAFE MODE (sometimes, not always) The BSOD says: SYSTEM_SERVICE_EXCEPTION STOP: 0x0000003b WimFsf.sys - Address FFFFF88001A6B76B base at FFFFF88001A600000, DateStamp 4a5bc362. Sometimes it shows the welcome screen, shows the destkop for a few seconds and then BSODs Already did: unplugged all the USB devices reset the CMOS I haven't installed any new software recently. What should I do? EDIT: I've managed to get into safe mode and it seems to works fine. When I go into normal mode it shows the desktop then it freezes... Is it more likely to be a software or hardware problem? EDIT2: I've managed to get into normal mode by disabling all the non-microsoft services & startup programs. One more thing: When I shut down my PC, on the "Logging off" screen appear some artifacts. I don't think it's because of my graphics card cause I've opened Black OPS and it worked fine. It's so strange... It still BSODS on startup (but there a ~=10% that it will not), and when it doesn't BSOD's it works fine...

  Read the article

• Ubuntu - No gnome-panels, no right-click, no internet, no hotkeys

  - by Darthfett

  Hey guys, I've been using Ubuntu (Maverick 10.10) on my desktop (ATI Radeon 5830) for about 3 weeks now, but all of a sudden I am unable to even use my computer. As soon as I start up, I see my desktop, with icons, but I don't see any gnome-panels, and I'm unable to get any options if I right-click. I can start programs by double clicking them. I also cannot get an internet connection. I've tried restarting gnome-panel by killing it, using Ctrl+Alt+5 to switch to a terminal (I don't have a shortcut to one on my desktop, and no hotkeys will work), but no luck. Restarting my computer has no effect upon this (I have to manually cut the power, since I don't know the terminal command). As far as I know, I have not made any changes, and I've never had any problems in the past. This started when I was playing Minecraft, but my internet crapped out, and no amount of re-trying the connection would work. I know it was my computer, as my brother's was working fine in the other room. Any clues as to what's going on? I'm more than willing to troubleshoot.

  Read the article

• Problem Uninstalling Microsoft Internet Explorer

  - by Roger F. Gay

  On Windows Vista Home Premium (x64) I am trying to uninstall Microsoft Internet Explorer. The procedures explained all over the web involve going through the control panel to Programs and Features. If MSIE is listed there, then uninstall in the usual way. If it is not listed there, click Turn Windows features on and off and deactivate it there. But Internet Explorer is not listed in either place. Background: I initiated some process in MSIE a couple of months ago that caused all web pages to no longer save login information or remain logged in when requested. As you can tell from the way I described that, I don't remember what it was and have no way to simply reverse it. I had a few problems with .NET Framework as well. So, I've uninstalled all browsers except MSIE and uninstalled .NET Framework. I've reinstalled .NET Framework and all other browsers. I have not been able to uninstall MSIE. Have Tried: I tried installing over the existing installation, but auto-update must be keeping it nicely up to date. The attempt simply produced an information window telling me that my current version is more up-to-date than the new version I tried to install.

  Read the article

• Internet explorer rejects cookies in kerberos protected intranet sites

  - by remix_tj

  I'm trying to build an intranet site using joomla. The webserver is using HTTP Kerberos authentication with mod_kerb_auth. Everything works fine, the users get authenticated and so on. But if i try to login to the administrator panel i can't because IE does not accept the needed cookies. No such problem with firefox. The intranet site is called "intranet_new" and is hosted by webintranet04, under the directory /var/www/vhosts/joomla/intranet_new/. I have my virtualhost for intranet_new containing this: <Location /> AuthType Kerberos AuthName "Kerberos Login" KrbMethodNegotiate On KrbMethodK5Passwd On KrbAuthRealms PROV.TV.LOCAL Krb5KeyTab /etc/apache2/HTTP.keytab require valid-user </Location> The same is for webintranet04 virtualhost, which is the default pointing to /var/www and contains: <Location /vhosts/joomla/> AuthType Kerberos AuthName "Kerberos Login" KrbMethodNegotiate On KrbMethodK5Passwd On KrbAuthRealms PROV.TV.LOCAL Krb5KeyTab /etc/apache2/HTTP.keytab require valid-user </Location> the very strange problem i have is that if i open http:// webintranet04/vhosts/joomla/intranet_new/administrator IE allows me to login, accepting cookie. If i open http:// intranet_new/administrator, instead, i loop on the login page. Last, intranet_new is a CNAME record of webintranet04. This is only an IE problem. I need: - the admin interface to work with IE - the "kerberized" zone to accept cookie, because i am deploying other programs requiring cookies.

  Read the article

• Why do I have three My Documents folders?

  - by root45

  I'm trying to fix my profile on Windows 7. Currently %USERPROFILE% points to C:\Users\myUsername My Documents is also at C:\Users\myUsername \\profileServer\profiles$\myUsername has TWO "My Documents" folders Neither of these folders contain what's in C:\Users\myUsername\My Documents Navigating to %USERPROFILE% in Windows Explorer displays two copies of everything, one local and one copy from the server. Programs use sort of a toss up between C:\Users\myUsername\My Documents or one of the two My Documents on profileServer. According to our sysadmins, My Documents is supposed to point to the profile server, but other folders should be local. How can I fix this so I have ONE copy of everything, with My Documents pointing to \\profileServer\profiles$\myUsername\Documents and everything else local? To be honest, I don't understand why this is so difficult and confusing. For example, why does Windows allow displaying two folders with the same name in the same directory? And why does inputting C:\Users\myUsername and %USERPROFILE% into Windows Explorer produce two different results? They should be identical. Some screenshots My directory on the profileServer My local user directory, C:\Users\myUsername Navigating to %USERPROFILE% in Windows Explorer Showing that %USERPROFILE% is set to a local directory

  Read the article

• windows 95 virtualization and CPU idle

  - by brtlvrs

  We are in the situation that we need to migrate our windows 95 systems (i know, that is so last century ). There is no hardware for a reasonable price available to run our windows 95 systems. So we are extending the overdue lifetime of it, by making them virtual. Now we see that VMware reports 100% CPU utilization of a windows 95 VM. This is because windows 95 doesn't know how to manage a CPU. For this reason software like rain or Waterfall, or CPUCool are introduced. The they are sending a HLT instruction to the CPU. This causes the CPU to halt and wait for new triggers to work. I've tested the mentioned programs in the VM, but they don't work, but generate errors. anyone has a valid workaround, solution ?? btw. I know that the best solutiuon is to replace the windows95 with windows XP. But in our situation that will take at least 5 years. Our windows 95 systems are running factory process control software.....

  Read the article

• Xampp can't start apachem windows xp

  - by jribeiro

  I formatted my computer a week ago. Installed wampp on windows xp, git and everything I needed. When I run git for the first time it told me it had a problem with my user folder (because of the accents) so I created a new user and migrated everything to the new one. After this wampp wouldn't start anymore. I uninstalled it and installed xampp which is what I'm using now. My problem is that even though I requesed xampp to install Apache as a service it isn't installed. It doesn't show in windows services screen. Xampp control panel shows mysql service running ok. When I click to install apache as a service it returns no error. When I click start apache no error is outputed. No file and no errors under c:/xampp/apache/log/ If I restart computer it says that apache service is not installed. I tried to reinstall wampp and the same problem occurs. If I run netstat -a -no nothing is running on port 80! What can I do??

  Read the article

• httpd.config Easy Apache WHM CentOS

  - by jessie

  First let me explain how I got to this situation. I run a Streaming Video Site. Videos are about 100-250MB in size at any given time there are 500 people on the site. So I guess that would make then static. Recently My site started getting really slow and the only way to fix it temporarily was to restart apache. Now there was no change in traffic that could have caused this. My site is not being attacked. My hosting company recomended to implement mpm_mod and suPHP. They did that by using Easy Apache in WHMS. Then everything was working fine but a little slow. I researched around and to my understanding that mpm will do that but be more table. I was told that installing FastCGI would speed things up just enough. Well that made everything worse. The site is slow and time's out. I used WHM and took off fastCGI but its still the same, it seems like everything i do as of now nothing changes. I even did a roll back on the htconfig file but that didn't work. I'm not sure how to fix this. and my hosting network guy wont be able to touch the problem until Tuesday. I have root access.

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• CLOSE_WAIT sockets burst - perhaps because of iptables settings?

  - by Fabrizio Giudici

  I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

  Read the article

• AMD Phenom II X2 555 BE, core unlock suddenly not working?

  - by user328271

  I've had a Phenom II X2 555 BE for around 2 - 3 years. When I got it, I immediately core unlocked it with my ECS A880GM-A3 mobo, which makes it turn into a Phenom II X4 B55. A few days ago, I installed Windows 7 64 bit to compensate for my 4 gigs of ram. When I start my system with its cores unlocked, it will restart after the BIOS screen. If I disable the core unlock, it boots to OS just fine. My question is: Does 64 bit OS makes a difference in core unlocking? Does my 3rd and 4th core burnt out? Also extra info: I tried core unlocking but keeping the 3rd and 4th core disabled and it still won't boot into OS. Could it be motherboard problems? Sorry for bad English. I will try to give additional information if needed. Thanks! Also it is worth mentioning I'm no computer expert but I tried to make my explanation as short as possible. I also asked my question on TomsHardware, but I had no answer till now so I decided to ask here too. anyone...?

  Read the article

• User http does not have write permissions directory?

  - by dwieeb

  I have a bit of an odd set up, I think. I have groups for each domain my server hosts, and I add the user http to each domain group along with the users that should have access to the groups' domains. In my php script running from a directory 'public_html', I try creating a file: <?php $output = ""; print exec('touch test 2>&1', $output); But I get touch: cannot touch `test': Permission denied and the file is not created. But here, clearly stated, the group has all permissions on the directory: drwxrwxr-x 5 dwieeb example.com 1024 Feb 4 05:19 public_html And here are the permissions on the php file in public_html that is trying to use the exec function: -rw-rw-r-- 1 dwieeb example.com 59 Feb 4 05:19 test.php How is this possible if http is part of the example.com group (as seen from a cat on /etc/group) and the directory has full permissions for the group? ... example.com:x:1000:dwieeb,http I'm stumped. EDIT (since apparently I'm not cool enough to answer my own questions yet): Ah, I found the problem. Yes, I restarted Nginx, but the php-fpm daemon must be restarted as well when http is added to the group for my domain. On Arch Linux: rc.d restart php-fpm

  Read the article

• unable to copy file to folder, permission denied without explanation

  - by ValekHalfHeart

  Recently Norton Internet security deleted ml.exe (an assembler I use to program in masm32) off of my computer, thinking that one of the programs I had written with it was a virus (it was most certainly not). Fortunately, I had a copy of ml.exe backed up in an external hard drive, and tried to copy it over to my computer. The old ml.exe was located in C:\masm32\bin, so I tried to copy the new one to that location. After disabling Norton (which had opened the folder and preventing me from accessing it), I am still unable to copy the new file to C:\masm32\bin. When I tried, Windows announced that I would need Administrator permission to copy the file. Since I'm an admin, I figured this wouldn't be a problem although it was unexpected, as I have never had to provide administrator permission to access this folder before. However, instead of prompting me to enter my password, Windows simply refuses to copy the file: I repeat, I was not asked to provide a password. It simply says that I do not have permission. Does anyone know what's happening and how to fix it? Is Norton still causing problems, or it something else?

  Read the article

• BIOS not detecting working SATA hard drive.

  - by Evan

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• IRC server connecting to another server

  - by Oxinabox

  I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

  Read the article

• How can I determine what is killing my network adapter win7 or vista?

  - by datatoo

  I thought this issue was like another person here, and that downloading the nvidia chipset drivers was the solution. However that is not all that is going on. This machine had Vista 64bit and is now Win7. Same issue with both. I have explicitly been denying network driver updates since getting things working again and when a Windows updates occurs on seemingly benign Office updates the adapter fails to work. Is the update process somehow protecting this machine by turning off things and it fails to recover connectivity after a restart? All that seems to ever work is a system restore. Which does work. Since there are 25 pending updates asking to do there thing, I hate to think this is a one by one update test to find the culprit. Any ideas? This has an integrated nic, video, and I guess audio on the motherboard. ES5200 intel cpu on a gateway 4800-05e I am not quite sure how to determine the actual network adapter. This is a wired adapter. I suppose worst case I can try another adapter if this keeps happening.

  Read the article

• Does my Oracle DBA need root access?

  - by Dr I

  I'm currently discussing with my Oracle DBA Collegue that request a root access on our production servers. I'm not so hot to let him use the root access on our production servers. He is arguing that he need it to perform some operations like restarting the server and some other obscure arguments. The point is that I'm not agree with him because I've set him a Oracle user/group and a dba group where Oracle user belong. Everything is running smoothy and without any root permissions for now. I also think that all administrative tasks like scheduled server restart and so one need to be operated by the proper administrator (The Systems administrator on our case) to avoid any kind of issues related to a misunderstanding of the infrastructure interactions. So, I need the help of both, sysadmins and Oracle DBAs to lead me on the correct direction. If my collegue really need this rights I'll give him, but I'm just basically quite affraid of that because of security and integrity concerns. I know that my collegue is really good as a Oracle DBA and he know is work very well, but I also know that I've very few cases where a software and its admin really need root access. Once again, I'm not looking for pros/cons but rather an advice on the way that I should take to deal with this situation.

  Read the article

• AGP 4x slot running at 2x

  - by Wesley

  Hi all, Here are the specs of the machine related to this question: AMD Athlon XP 2400+ @ 2 GHz / 2x 512MB PC3200 DDR RAM / 3D Fuzion 128MB GeForce 6200 AGP / WD 160GB IDE HDD / FIC AM37 (mobo) / Codegen 350W PSU / Windows XP Pro SP3 So, for some odd reason, the GeForce 6200 that is in the AGP 4x slot is not running at 4x, but 2x. The card itself supports AGP 4x and even 8x. When I enter the BIOS, the options for the AGP slot only allow 2x as the max. Before, the max option for the AGP slot in the BIOS was 4x. (I do get the 4x option after I reset CMOS, but it does not stick after a restart.) I don't exactly know what the problem could be, but a few weeks ago, this machine's hard drive was reformatted and got a fresh install of XP. Also, I did install Rivatuner, but I never overclocked it at all. (I uninstalled it after thinking that it had done something.) Otherwise, I cannot figure out the cause of the problem. Does anybody have an idea why this is happening? (Would I have to do another reformat?) Thanks in advance. PS: the other options for the AGP slot are aperture size (which I tried changing, but it did nothing) and FastWrite (enabled by default).

  Read the article

• How to fix IE starting when I try to start Opera?

  - by Scott Leis

  I have a problem that started today, where trying to run any of the 3 versions of Opera I have installed causes Internet Explorer to start instead. The Opera versions I have installed are 9.64, 10.10, and 10.63. My OS is Windows Vista with the latest critical/important updates. The behaviour is the same regardless of whether I double-click a shortcut to Opera, double-click on Opera.exe in one of the install directories, or run Opera.exe with the full path from Start-Run. The only work-around I've found is to right-click Opera.exe or a shortcut, and click "Run as administrator". This starts Opera, and it appears to work normally. Opera seems to be the only program so affected. I've checked Firefox and a few other (non-browser) programs, and they work normally. When IE starts instead of Opera, there are always two instances of iexplore.exe started, and they both crash before I can do anything else. IE also crashes if I try to start it from its own shortcut, but I don't know if that only started today, since I hadn't used IE for a few weeks. Does anyone know what might cause this and how to fix it? It's possible my PC has a virus, but BitDefender (for which I have automatic updates enabled) hasn't detected anything.

  Read the article

• Windows 7, going crazy with environment variables

  - by roymustang86

  So, I am trying to learn java. I installed the JDK and proceeded to write a few programs. Each time, I have to give the path to javac.exe to compile the .java file. SO, I decided to tweak the %PATH% variable. And no matter what I change it to, it doesn't work. when I do an echo %PATH%, I get 'Program' is not recognized as an internal or external command, operable program or batch file. This is my Path variable contents : C:\app\product\11.1.0\client_1\bin;%CommonProgramFiles%\Microsoft Shared\Windows Live;%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;"C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\";"C:\Program Files\Broadcom\Broadcom 802.11";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\12.0\DLLShared\";"C:\Program Files (x86)\Roxio\OEM\AudioCore\";"C:\Program Files (x86)\Intel\Services\IPT\" How do I work around this? the double quotes were not there before, I added it thinking the space was the problem.

  Read the article

• Computer always freezing after random periods of time. No errors listed.

  - by Wesley

  Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

  Read the article

• Openbsd init script for ssh VPN tunnel

  - by manthis

  I have a server hosting SSH tunnels and Openbsd 4.5 clients connecting to it. Things work just fine but I am in the need of automating the connection from the client to the server. So that if the client is accidentally rebooted, then the connection initiates unattended. So it should be as straight forward as to include the ssh connection in an init script. However I have miserably failed to do so by including it to /etc/rc.local, which is the file I usually do this sort of things in. Right now I am using autossh to also restart the connection if necessary and the script that I put on /etc/rc.local follows: #!/bin/sh # # Example script to start up tunnel with autossh. # # This script will tunnel 2200 from the remote host # to 22 on the local host. On remote host do: # ssh -p 2200 localhost # # $Id: autossh.host,v 1.6 2004/01/24 05:53:09 harding Exp $ # ID=root HOST=example.com #AUTOSSH_POLL=600 #AUTOSSH_PORT=20000 #AUTOSSH_GATETIME=30 #AUTOSSH_LOGFILE=$HOST.log #AUTOSSH_DEBUG=yes #AUTOSSH_PATH=/usr/local/bin/ssh export AUTOSSH_POLL AUTOSSH_LOGFILE AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -f -M 20000 ${ID}@${HOST} The script detaches just fine when run manually so I just include it on /etc/rc.local as echo -n 'starting local daemons:' if [ -x /usr/local/sbin/autossh.sh ]; then echo -n 'ssh tunnel' /usr/local/sbin/autossh.sh fi echo '.' I have also tried calling it from /etc/hostname.tun0 in case there may be issues with /etc/rc.local not being called at the right time when network connections are ready, so I would use: inet 10.254.254.2 255.255.255.252 10.254.254.1 !/usr/local/sbin/autossh.sh Your input is highly appreciated.

  Read the article

• What is the fastest way to clone an INNODB table within the same server?

  - by Vic

  Our development server is a replication slave of our production server. We have a script that developers use if they want to run their applications/bug fixes against fresh data. That script looks like this: dbs=( analytics auth logs users ) server=localhost conn="-h ${server} -u ${username} --password=${password}" # Stop the replication client so we don't encounter weird data. echo "STOP SLAVE" | mysql ${conn} # Bunch of bulk insert optimizations echo "SET autocommit=0" | mysql ${conn} echo "SET unique_checks=0" | mysql ${conn} echo "SET foreign_key_checks=0" | mysql ${conn} # Restore all databases and tables. for sourcedb in ${dbs[*]} do destdb=${prefix}${sourcedb} echo "Dropping database ${destdb}..." echo "DROP DATABASE IF EXISTS ${destdb}" | mysql ${conn} echo "CREATE DATABASE ${destdb}" | mysql ${conn} # First, all the tables. for table in `echo "SHOW FULL TABLES WHERE Table_type <> 'VIEW'" | mysql $conn $sourcedb | tail -n +2`; do if [[ "${table}" != 'BASE' && "${table}" != 'TABLE' && "${table}" != 'VIEW' ]] ; then createTable=`echo "SHOW CREATE TABLE ${table}"|mysql -B -r $conn $sourcedb|tail -n +2|cut -f 2-` echo "Restoring ${destdb}/${table}..." echo "$createTable ;" | mysql $conn $destdb insertData="INSERT INTO ${destdb}.${table} SELECT * FROM ${sourcedb}.${table}" echo "$insertData" | mysql $conn $destdb fi fi done done echo "SET foreign_key_checks=1" | mysql ${conn} echo "SET unique_checks=1" | mysql ${conn} echo "COMMIT" | mysql ${conn} # Restart the replication client echo "START SLAVE" | mysql ${conn} All of these operations are, as I mentioned, within the same server. Is there a faster way to clone the tables I'm not seeing? They're all INNODB tables. Thanks!

  Read the article

• RTorrent stops my torrents, crashes, and I have to manually re-add torrents and start them. How can I stop this cycle of doom?

  - by meder

  I cannot use transmission which is the best torrent client because it's banned from one of the trackers I use, so I am forced to use rtorrent. Normally I am all for command-line programs, however rtorrent ( 0.8.6/0.12.6 ) is simply frustrating. It is not intuitive, imo. I have 400 MB left on the HD and that's more than enough to dl this 200 MB avi. Rtorrent stops the download, though. It says [CLOSED] near the torrent. I do ctrl-r and that invokes the local hash check, and after that's done rtorrent simply dies ( wtf? ). Afterwards, it gives me rtorrent: TrackerManager::send_later() m_control->set() == DownloadInfo::STOPPED. So that leads me to open rtorrent again, then hit ENTER and /home/meder/file.avi.torrent, down arrow, and ctrl-S. I am looking for multiple things... How can I tell rtorrent to not worry about disk space? Again, it stops the torrent if my HD only has 400 mb when the torrent I'm dling is 200 mb ( there are no other torrents ). Why does ctrl-R fail hard? Why does it cause rtorrent to crash? If #2 is not solvable, can someone provide an easy way to add a torrent and start it, a more efficient method than typing the torrent name, hitting the down arrow, and ctrl-S?

  Read the article

• Changing open-files-limit in mysql 5.5

  - by davidv

  I'm having an issue with mysql 5.5 running on Ubuntu 12.04 with the open-files-limit parameter. I recently noticed some problems due to the 1024 limit, and actually the main system limit was set to 1024, so I modified /etc/security/limits.conf with the following: * soft nofile 32000 * hard nofile 32000 root soft nofile 32000 root hard nofile 32000 After that I check the ulimit value for root and even for mysql user, both returned the new value: 32000, so I assume the change has already been done. I also changed the value at the my.cnf file, setting open-files-limit to 24000, like this: open-files-limit = 24000 Now comes the odd part, when I restart the mysql service and check the open_files_limit variable, it returns that it's still set to 1024, so I'm having the same problems that before (obviously), I tried to use open-files-limit instead open_files_limit in the my.cnf config file, same result, BUT if I override the service command to start the service and start only using mysqld (no additional parameters), the service starts and when I check the parameter it returns 32000... I don't know where it's taking that value from, as it's not set at my.cnf and it's not being given through command line, at least, not for myself. Any ideas about why it's not working the change and how to solve it the normal way (launching it through service...)?

  Read the article

< Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >