Search Results

Search found 9557 results on 383 pages for 'x86 64'.

Page 317/383 | < Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >

• IKE Phase 1 Aggressive Mode exchange does not complete

  - by Isaac Sutherland

  I've configured a 3G IP Gateway of mine to connect using IKE Phase 1 Aggressive Mode with PSK to my openswan installation running on Ubuntu server 12.04. I've configured openswan as follows: /etc/ipsec.conf: version 2.0 config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn net-to-net authby=secret left=192.168.0.11 [email protected] leftsubnet=10.1.0.0/16 leftsourceip=10.1.0.1 right=%any [email protected] rightsubnet=192.168.127.0/24 rightsourceip=192.168.127.254 aggrmode=yes ike=aes128-md5;modp1536 auto=add /etc/ipsec.secrets: @left.paxcoda.com @right.paxcoda.com: PSK "testpassword" Note that both left and right are NAT'd, with dynamic public IP's. My left ISP gives my router a public IP, but my right ISP gives me a shared dynamic public IP and dynamic private IP. I have dynamic dns for the public ip on the left side. Here is what I see when I sniff the ISAKMP protocol: 21:17:31.228715 IP (tos 0x0, ttl 235, id 43639, offset 0, flags [none], proto UDP (17), length 437) 74.198.87.93.49604 > 192.168.0.11.isakmp: [udp sum ok] isakmp 1.0 msgid 00000000 cookie da31a7896e2a1958->0000000000000000: phase 1 I agg: (sa: doi=ipsec situation=identity (p: #1 protoid=isakmp transform=1 (t: #1 id=ike (type=enc value=aes)(type=keylen value=0080)(type=hash value=md5)(type=auth value=preshared)(type=group desc value=modp1536)(type=lifetype value=sec)(type=lifeduration len=4 value=00015180)))) (ke: key len=192) (nonce: n len=16 data=(da31a7896e2a19582b33...0000001462b01880674b3739630ca7558cec8a89)) (id: idtype=FQDN protoid=0 port=0 len=17 right.paxcoda.com) (vid: len=16) (vid: len=16) (vid: len=16) (vid: len=16) 21:17:31.236720 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto UDP (17), length 456) 192.168.0.11.isakmp > 74.198.87.93.49604: [bad udp cksum 0x649c -> 0xcd2f!] isakmp 1.0 msgid 00000000 cookie da31a7896e2a1958->5b9776d4ea8b61b7: phase 1 R agg: (sa: doi=ipsec situation=identity (p: #1 protoid=isakmp transform=1 (t: #1 id=ike (type=enc value=aes)(type=keylen value=0080)(type=hash value=md5)(type=auth value=preshared)(type=group desc value=modp1536)(type=lifetype value=sec)(type=lifeduration len=4 value=00015180)))) (ke: key len=192) (nonce: n len=16 data=(32ccefcb793afb368975...000000144a131c81070358455c5728f20e95452f)) (id: idtype=FQDN protoid=0 port=0 len=16 left.paxcoda.com) (hash: len=16) (vid: len=16) (pay20) (pay20) (vid: len=16) However, my 3G Gateway (on the right) doesn't respond, and I don't know why. I think left's response is indeed getting through to my gateway, because in another question, I was trying to set up a similar scenario with Main Mode IKE, and in that case it looks as though at least one of the three 2-way main mode exchanges succeeded. What other explanation for the failure is there? (The 3G Gateway I'm using on the right is a Moxa G3150, by the way.)

  Read the article

• Xcopy /exclude does not exclude some of the specified criteria

  - by Richard Z.

  Good afternoon. I want xcopy to copy all files meeting a certain criteria located in the C drive to a specific folder, except ones located in the directories specified in excl.txt. The exclusions only work partially - the files located in %systemroot%, %programfiles% and in each profile's appdata are still copied, even though those directories are listed in excl.txt. How do I make xcopy skip those directories, preferentially still using environment vars to specify the paths? My current syntax is: xcopy /s /c /d /h /i /r /y /g /f /EXCLUDE:excl.txt %systemdrive%\*.doc f:\test\ excl.txt currently contains the following: \%temp%\ \%userprofile%\appdata \%programfiles%\ \%programfiles(x86)%\ \%systemroot%\ \%programdata%\ appdata windows %programfiles% Thank you very much.

  Read the article

• Block IP Address including ICMP using UFW

  - by dr jimbob

  I prefer ufw to iptables for configuring my software firewall. After reading about this vulnerability also on askubuntu, I decided to block the fixed IP of the control server: 212.7.208.65. I don't think I'm vulnerable to this particular worm (and understand the IP could easily change), but wanted to answer this particular comment about how you would configure a firewall to block it. I planned on using: # sudo ufw deny to 212.7.208.65 # sudo ufw deny from 212.7.208.65 However as a test that the rules were working, I tried pinging after I setup the rules and saw that my default ufw settings let ICMP through even from an IP address set to REJECT or DENY. # ping 212.7.208.65 PING 212.7.208.65 (212.7.208.65) 56(84) bytes of data. 64 bytes from 212.7.208.65: icmp_seq=1 ttl=52 time=79.6 ms ^C --- 212.7.208.65 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 79.630/79.630/79.630/0.000 ms Now, I'm worried that my ICMP settings are too generous (conceivably this or a future worm could setup an ICMP tunnel to bypass my firewall rules). I believe this is the relevant part of my iptables rules is given below (and even though grep doesn't show it; the rules are associated with the chains shown): # sudo iptables -L -n | grep -E '(INPUT|user-input|before-input|icmp |212.7.208.65)' Chain INPUT (policy DROP) ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) DROP all -- 0.0.0.0/0 212.7.208.65 DROP all -- 212.7.208.65 0.0.0.0/0 How should I go about making it so ufw blocks ICMP when I specifically attempt to block an IP address? My /etc/ufw/before.rules has in part: # ok icmp codes -A ufw-before-input -p icmp --icmp-type destination-unreachable -j ACCEPT -A ufw-before-input -p icmp --icmp-type source-quench -j ACCEPT -A ufw-before-input -p icmp --icmp-type time-exceeded -j ACCEPT -A ufw-before-input -p icmp --icmp-type parameter-problem -j ACCEPT -A ufw-before-input -p icmp --icmp-type echo-request -j ACCEPT I'm tried changing ACCEPT above to ufw-user-input: # ok icmp codes -A ufw-before-input -p icmp --icmp-type destination-unreachable -j ufw-user-input -A ufw-before-input -p icmp --icmp-type source-quench -j ufw-user-input -A ufw-before-input -p icmp --icmp-type time-exceeded -j ufw-user-input -A ufw-before-input -p icmp --icmp-type parameter-problem -j ufw-user-input -A ufw-before-input -p icmp --icmp-type echo-request -j ufw-user-input But ufw wouldn't restart after that. I'm not sure why (still troubleshooting) and also not sure if this is sensible? Will there be any negative effects (besides forcing the software firewall to force ICMP through a few more rules)?

  Read the article

• Root directory permissions on Mac OS X 10.6?

  - by Agos

  Hi, I was wondering if it's normal that the root directory / should be owned by “root”. I get asked for my password every time I want to do something there (e.g. save a file, create a directory) and I don't remember this happening before (though this may just be my faulty memory). Here's the relevant terminal output: MacBook:~ ago$ ls -lah / total 37311 drwxr-xr-x@ 35 root staff 1,2K 22 Mar 12:34 . drwxr-xr-x@ 35 root staff 1,2K 22 Mar 12:34 .. -rw-rw-r--@ 1 root admin 21K 22 Mar 10:21 .DS_Store drwx------ 3 root admin 102B 28 Feb 2008 .Spotlight-V100 d-wx-wx-wt 2 root admin 68B 31 Ago 2009 .Trashes -rw-r--r--@ 1 ago 501 45K 23 Gen 2008 .VolumeIcon.icns srwxrwxrwx 1 root staff 0B 22 Mar 12:34 .dbfseventsd ---------- 1 root admin 0B 23 Giu 2009 .file drwx------ 27 root admin 918B 22 Mar 10:55 .fseventsd -rw-r--r--@ 1 ago admin 59B 30 Ott 2007 .hidden -rw------- 1 root wheel 320K 30 Nov 11:42 .hotfiles.btree drwxr-xr-x@ 2 root wheel 68B 18 Mag 2009 .vol drwxrwxr-x+ 276 root admin 9,2K 19 Mar 18:28 Applications drwxrwxr-x@ 21 root admin 714B 14 Nov 12:01 Developer drwxrwxr-t+ 74 root admin 2,5K 18 Dic 22:14 Library drwxr-xr-x@ 2 root wheel 68B 23 Giu 2009 Network drwxr-xr-x 4 root wheel 136B 13 Nov 17:49 System drwxr-xr-x 6 root admin 204B 31 Ago 2009 Users drwxrwxrwt@ 4 root admin 136B 22 Mar 12:35 Volumes drwxr-xr-x@ 39 root wheel 1,3K 13 Nov 17:44 bin drwxrwxr-t@ 2 root admin 68B 23 Giu 2009 cores dr-xr-xr-x 3 root wheel 5,1K 17 Mar 11:29 dev lrwxr-xr-x@ 1 root wheel 11B 31 Ago 2009 etc -> private/etc dr-xr-xr-x 2 root wheel 1B 17 Mar 11:30 home drwxrwxrwt@ 3 root wheel 102B 31 Ago 2009 lost+found -rw-r--r--@ 1 root wheel 18M 3 Nov 19:40 mach_kernel dr-xr-xr-x 2 root wheel 1B 17 Mar 11:30 net drwxr-xr-x@ 3 root admin 102B 24 Nov 2007 opt drwxr-xr-x@ 6 root wheel 204B 31 Ago 2009 private drwxr-xr-x@ 64 root wheel 2,1K 13 Nov 17:44 sbin lrwxr-xr-x@ 1 root wheel 11B 31 Ago 2009 tmp -> private/tmp drwxr-xr-x@ 17 root wheel 578B 12 Set 2009 usr lrwxr-xr-x@ 1 root wheel 11B 31 Ago 2009 var -> private/var Are these ownerships / permissions ok? Should I chmod/chown something? Thanks in advance

  Read the article

• Slow Memcached: Average 10ms memcached `get`

  - by Chris W.

  We're using Newrelic to measure our Python/Django application performance. Newrelic is reporting that across our system "Memcached" is taking an average of 12ms to respond to commands. Drilling down into the top dozen or so web views (by # of requests) I can see that some Memcache get take up to 30ms; I can't find a single use of Memcache get that returns in less than 10ms. More details on the system architecture: Currently we have four application servers each of which has a memcached member. All four memcached members participate in a memcache cluster. We're running on a cloud hosting provider and all traffic is running across the "internal" network (via "internal" IPs) When I ping from one application server to another the responses are in ~0.5ms Isn't 10ms a slow response time for Memcached? As far as I understand if you think "Memcache is too slow" then "you're doing it wrong". So am I doing it wrong? Here's the output of the memcache-top command: memcache-top v0.7 (default port: 11211, color: on, refresh: 3 seconds) INSTANCE USAGE HIT % CONN TIME EVICT/s GETS/s SETS/s READ/s WRITE/s cache1:11211 37.1% 62.7% 10 5.3ms 0.0 73 9 3958 84.6K cache2:11211 42.4% 60.8% 11 4.4ms 0.0 46 12 3848 62.2K cache3:11211 37.5% 66.5% 12 4.2ms 0.0 75 17 6056 170.4K AVERAGE: 39.0% 63.3% 11 4.6ms 0.0 64 13 4620 105.7K TOTAL: 0.1GB/ 0.4GB 33 13.9ms 0.0 193 38 13.5K 317.2K (ctrl-c to quit.) ** Here is the output of the top command on one machine: ** (Roughly the same on all cluster machines. As you can see there is very low CPU utilization, because these machines only run memcache.) top - 21:48:56 up 1 day, 4:56, 1 user, load average: 0.01, 0.06, 0.05 Tasks: 70 total, 1 running, 69 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.3%st Mem: 501392k total, 424940k used, 76452k free, 66416k buffers Swap: 499996k total, 13064k used, 486932k free, 181168k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 6519 nobody 20 0 384m 74m 880 S 1.0 15.3 18:22.97 memcached 3 root 20 0 0 0 0 S 0.3 0.0 0:38.03 ksoftirqd/0 1 root 20 0 24332 1552 776 S 0.0 0.3 0:00.56 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 4 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kworker/0:0 5 root 20 0 0 0 0 S 0.0 0.0 0:00.02 kworker/u:0 6 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0.0 0.0 0:00.62 watchdog/0 8 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 cpuset 9 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 khelper ...output truncated...

  Read the article

• Adding a Microsoft Exchange 2010 account to my Windows Phone 7.5 mobile (Nokia Lumia 800) without trusted certificate

  - by MAXE

  I have problems in creating an account on my Nokia Lumia 800 (OS version: 7.10.8773.98, of course with Windows Phone 7.1 mounted with all updates) to one of my company's Microsoft Exchange 2010 server, because it cannot provide a trusted certificate...but only when contacting it from outside my network (like https ://mail.(CompanyName).com). Accessing the server from inside my network (pointing directly to the machine name or internal IP address: https ://(MachineName) or https ://10.0.1.200) gives me NO PROBLEM AT ALL! Setting correctly (I guess) all the parameters for the account (accessing from outside my network), the connection (after correctly set my credentials as asked) will not be established. It gives the next error (translated from my language manually): Error of <CompanyName> There is a problem with the certificate of (Server Address). Please contact support or the provider. Last try: X minutes ago Error code: 80072F06 I've tried all possible configurations and parameters (including the check The server requires an encrypted (SSL) connection, of course), but no way. EDITED: As suggested by Oliver Salzburg, I also tried this way without any results. I tried so: I went to my OWA (Outlook Web Access) that gives me the same problem (problems the certificate, it's not trusted) After accepting to continue, I clicked on the Error in Certificate button of the Internet Explorer 9 address bar - Show Certificates - page Details, show: - Copy to file... button - in the exporting wizard: Next - Binary encoding DER X.509 (.cer) (but there was also Base binary 64 X.509 (.cer), no way) - Next - saved to a new file From my Google Mail Account, I sent a mail to myself the certificate as attachment I read the mail from my WP7 phone, saved the attachment and then ran it: answering Yes to Do you wany to install the certificate? of course... Closed any active program and rebooted the phone Re-tried in synchronizing my account....:(...SAME PROBLEM! EDITED 2: Thanks again to Oliver Salzburg, I tried the next solution: I went to the site https://www.testexchangeconnectivity.com/ I selected Exchange ActiveSync option, as suggested I setted all my parameters, as I made for my phone I also setted the option Ignore SSL attendibility (and in another test I didn't) I performed my test This is the complete log (I removed my parameters): Seems the same problem (machine name in the certificate is different from the external Exchange website domain name?)! It is possible to get rid of this annoying (I know by myself who is this server!) problem? Thank you very much.

  Read the article

• Python Django sites on Apache+mod_wsgi with nginx proxy: highly fluctuating performance

  - by Halfgaar

  I have an Ubuntu 10.04 box running several dozen Python Django sites using mod_wsgi (embedded mode; the faster mode, if properly configured). Performance highly fluctuates. Sometimes fast, sometimes several seconds delay. The smokeping graphs are al over the place. Recently, I also added an nginx proxy for the static content, in the hopes it would cure the highly fluctuating performance. But, even though it reduced the number of requests Apache has to process significantly, it didn't help with the main problem. When clicking around on websites while running htop, it can be seen that sometimes requests are almost instant, whereas sometimes it causes Apache to consume 100% CPU for a few seconds. I really don't understand where this fluctuation comes from. I have configured the mpm_worker for Apache like this: StartServers 1 MinSpareThreads 50 MaxSpareThreads 50 ThreadLimit 64 ThreadsPerChild 50 MaxClients 50 ServerLimit 1 MaxRequestsPerChild 0 MaxMemFree 2048 1 server with 50 threads, max 50 clients. Munin and apache2ctl -t both show a consistent presence of workers; they are not destroyed and created all the time. Yet, it behaves as such. This tells me that once a sub interpreter is created, it should remain in memory, yet it seems sites have to reload all the time. I also have a nginx+gunicorn box, which performs quite well. I would really like to know why Apache is so random. This is a virtual host config: <VirtualHost *:81> ServerAdmin [email protected] ServerName example.com DocumentRoot /srv/http/site/bla Alias /static/ /srv/http/site/static Alias /media/ /srv/http/site/media WSGIScriptAlias / /srv/http/site/passenger_wsgi.py <Directory /> AllowOverride None </Directory> <Directory /srv/http/site> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> Ubuntu 10.04 Apache 2.2.14 mod_wsgi 2.8 nginx 0.7.65 Edit: I've put some code in the settings.py file of a site that writes the date to a tmp file whenever it's loaded. I can now see that the site is not randomly reloaded all the time, so Apache must be keeping it in memory. So, that's good, except it doesn't bring me closer to an answer... Edit: I just found an error that might also be related to this: File "/usr/lib/python2.6/subprocess.py", line 633, in __init__ errread, errwrite) File "/usr/lib/python2.6/subprocess.py", line 1049, in _execute_child self.pid = os.fork() OSError: [Errno 12] Cannot allocate memory The server has 600 of 2000 MB free, which should be plenty. Is there a limit that is set on Apache or WSGI somewhere?

  Read the article

• Windows 7 fails to install on KVM with qemu

  - by kief_morris

  I'm trying to install Windows 7 on a virtual machine on my 64 bit Ubuntu Karmic box. I get to the point of selecting my language settings and clicking 'install now', but a short while later I get a blue screen of death. I've tried a few variations, including using the 32 bit (fails very quickly). The virt-install command I've tried includes this: sudo virt-install --connect qemu:///system -n ksm-win7 -r 2048 \ --disk path=/home/kief/VM-Images/ksm-win7.qcow2,size=50 \ -c /var/Software/Windows7/Full/64bit/SW_DVD5_SA_Win_Ent_7_64BIT_English_Full_MLF_X15-70749.ISO \ --vnc --os-type windows --os-variant vista --hvm The limited info I could find suggested that 'vista' should work as the --os-variant, I haven't found any values specific to windows 7. Here's my blue screen: I've found very little by Googling, so I'm guessing this isn't a case of KVM simply not supporting Windows 7. Thanks for any help. Update: I have been able to successfully create a Windows 7 VM using the graphical "Virtual Machine Manager" app, although I don't really understand the cause of the problem with the VM created with virt-install. Comparing the configuration files under /etc/libvirt/qemu provides some clues, although I don't know enough to interpret them properly. The interesting differences in the two VM configurations are: --- win7-virt-install.xml +++ win7-vmm.xml -<domain type='qemu'> +<domain type='kvm'> @@ -21 +21 @@ - <emulator>/usr/bin/qemu-system-x86_64</emulator> + <emulator>/usr/bin/kvm</emulator> @@ -23 +23 @@ - <source file='/home/kief/VM-Images/ksm-win7.qcow2'/> + <source file='/var/lib/libvirt/images/ksm-win7x64.img'/> I'm not sure if this means the working VM is not using qemu at all, or if there is some other difference in the way it's used with kvm. Update2: So I've answered my own question (mostly) below. A KVM VM needs to use KVM's own CPU emulation rather than qemu's in order for me to get Windows 7 installed. I'm not sure whether there is something that can be done to get it working on a qemu-emulation CPU, or whether a newer version will support it. But at least it is possible to get it running on a KVM VM.

  Read the article

• Update KB951847 (3.5 SP1 and Family Update) fails on Windows Server 2003 repeatedly

  - by Ducain

  We have a Win2K3 server that is perpetually stuck on the following update: Microsoft .NET Framework 3.5 Service Pack 1 and .NET Framework 3.5 Family Update for .NET versions 2.0 through 3.5 (KB951847) x86 It fails every time, and I'm at a loss on what to do about it. WHAT I'VE TRIED: Saw an article that said to turn off the update service, rename C:\Windows\SoftareDistribution\ and then restart the update service. Did this, ran the update, and it failed on this same one. I tried to run the update manually at C:\Windows\SoftwareDistribution\Downloads\Install\ and again it fails. Says, "None of the products that are addressed by this software update are installed on this computer. Click Cancel to exit setup." Because of this issue, none of the previous updates will work either. I will give one large pink-glazed donut with sprinkles to anyone who can help me slay this beast.

  Read the article

• how to read mac address with sed vs python

  - by getjoefree

  before, i can read mac with awk tools in windows or winpe, but now it don't support winpe 4.0 64-bit. i want to get this result "set mac=A4BADB9D1E8E" with python 2.6, who could help to me. thanks a lot! as follows: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" D:\LOG\WINMAC.BAT getmac.sed: /Realtek/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; } and "ipconfig -all" command log as bellows: ipconfig -all mac.log Ethernet adapter Ethernet: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : WKSCN.WISTRON Description . . . . . . . . . . . : Realtek PCIe FE Family Controller Physical Address. . . . . . . . . : 24-B6-FD-1F-41-E7 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes

  Read the article

• RHEL5: Can't create sparse file bigger than 256GB in tmpfs

  - by John Kugelman

  /var/log/lastlog gets written to when you log in. The size of this file is based off of the largest UID in the system. The larger the maximum UID, the larger this file is. Thankfully it's a sparse file so the size on disk is much smaller than the size ls reports (ls -s reports the size on disk). On our system we're authenticating against an Active Directory server, and the UIDs users are assigned end up being really, really large. Like, say, UID 900,000,000 for the first AD user, 900,000,001 for the second, etc. That's strange but should be okay. It results in /var/log/lastlog being huuuuuge, though--once an AD user logs in lastlog shows up as 280GB. Its real size is still small, thankfully. This works fine when /var/log/lastlog is stored on the hard drive on an ext3 filesystem. It breaks, however, if lastlog is stored in a tmpfs filesystem. Then it appears that the max file size for any file on the tmpfs is 256GB, so the sessreg program errors out trying to write to lastlog. Where is this 256GB limit coming from, and how can I increase it? As a simple test for creating large sparse files I've been doing: dd if=/dev/zero of=sparse-file bs=1 count=1 seek=300GB I've tried Googling for "tmpfs max file size", "256GB filesystem limit", "linux max file size", things like that. I haven't been able to find much. The only mention of 256GB I can find is that ext3 filesystems with 2KB blocks are limited to 256GB files. But our hard drives are formatted with 4K blocks so that doesn't seem to be it--not to mention this is happening in a tmpfs mounted ON TOP of the hard drive so the ext3 partition shouldn't be a factor. This is all happening on a 64-bit Red Hat Enterprise Linux 5.4 system. Interestingly, on my personal development machine, which is a 32-bit Fedora Core 6 box, I can create 300GB+ files in tmpfs filesystems no problem. On the RHEL5.4 systems it is no go.

  Read the article

• Can't get Apache 2.2.21 to compile with OpenSSL support

  - by angstwad

  Alright -- having a bad couple days here compiling Apache 2.2.21 on CentOS 5.7 with the following configure commands: ./configure --enable-ssl=shared --with-ssl=/usr/local/openssl I've compiled from source OpenSSL 1.0.0e from source: ./config --prefix=/usr/local --openssldir=/usr/local/openssl shared zlib-dynamic I attempt to start Apache and it returns: httpd: Syntax error on line 54 of /usr/local/apache2/conf/httpd.conf: Cannot load /usr/local/apache2/modules/mod_ssl.so into server: /usr/local/apache2/modules/mod_ssl.so: undefined symbol: SSL_get_servername If I look at how the libraries are linked, this is what I get: [root@web1 modules]# ldd mod_ssl.so libssl.so.6 => /lib64/libssl.so.6 (0x00002aaaaace4000) libcrypto.so.6 => /lib64/libcrypto.so.6 (0x00002aaaaaf30000) libdl.so.2 => /lib64/libdl.so.2 (0x00002aaaab281000) libz.so.1 => /lib64/libz.so.1 (0x00002aaaab486000) libpthread.so.0 => /lib64/libpthread.so.0 (0x00002aaaab69a000) libc.so.6 => /lib64/libc.so.6 (0x00002aaaab8b5000) libgssapi_krb5.so.2 => /usr/lib64/libgssapi_krb5.so.2 (0x00002aaaabc0e000) libkrb5.so.3 => /usr/lib64/libkrb5.so.3 (0x00002aaaabe3c000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x00002aaaac0d1000) libk5crypto.so.3 => /usr/lib64/libk5crypto.so.3 (0x00002aaaac2d4000) /lib64/ld-linux-x86-64.so.2 (0x0000555555554000) libkrb5support.so.0 => /usr/lib64/libkrb5support.so.0 (0x00002aaaac4f9000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x00002aaaac702000) libresolv.so.2 => /lib64/libresolv.so.2 (0x00002aaaac904000) libselinux.so.1 => /lib64/libselinux.so.1 (0x00002aaaacb19000) libsepol.so.1 => /lib64/libsepol.so.1 (0x00002aaaacd32000) Basically, I've tired compiling from source OpenSSL (both 0.9.8r and 1e), having yum reinstall from the repos, done a make clean and remade both OpenSSL and Apache numerous times -- but I can't get it to compile into the apache base or dynamically as a shared object file. What am I doing wrong here? Update 1: After doing a make clean and make distclean, I've reconfigured with the same parameters as above without any effect. The config.log is at Pastebin. Update 2: Modifying the LD_LIBRARY_PATH had no effect on the lib-deps of mod_ssl.so. UPDATE 3: I've compiled and recompiled many times, and verified with ldconfig that the OpenSSL libs dir is in my path, and included in ld.so.conf. Still cannot get httpd/mod_ssl to load the library at runtime.

  Read the article

• Linux RAID-0 performance doesn't scale up over 1 GB/s

  - by wazoox

  I have trouble getting the max throughput out of my setup. The hardware is as follow : dual Quad-Core AMD Opteron(tm) Processor 2376 16 GB DDR2 ECC RAM dual Adaptec 52245 RAID controllers 48 1 TB SATA drives set up as 2 RAID-6 arrays (256KB stripe) + spares. Software : Plain vanilla 2.6.32.25 kernel, compiled for AMD-64, optimized for NUMA; Debian Lenny userland. benchmarks run : disktest, bonnie++, dd, etc. All give the same results. No discrepancy here. io scheduler used : noop. Yeah, no trick here. Up until now I basically assumed that striping (RAID 0) several physical devices should augment performance roughly linearly. However this is not the case here : each RAID array achieves about 780 MB/s write, sustained, and 1 GB/s read, sustained. writing to both RAID arrays simultaneously with two different processes gives 750 + 750 MB/s, and reading from both gives 1 + 1 GB/s. however when I stripe both arrays together, using either mdadm or lvm, the performance is about 850 MB/s writing and 1.4 GB/s reading. at least 30% less than expected! running two parallel writer or reader processes against the striped arrays doesn't enhance the figures, in fact it degrades performance even further. So what's happening here? Basically I ruled out bus or memory contention, because when I run dd on both drives simultaneously, aggregate write speed actually reach 1.5 GB/s and reading speed tops 2 GB/s. So it's not the PCIe bus. I suppose it's not the RAM. It's not the filesystem, because I get exactly the same numbers benchmarking against the raw device or using XFS. And I also get exactly the same performance using either LVM striping and md striping. What's wrong? What's preventing a process from going up to the max possible throughput? Is Linux striping defective? What other tests could I run?

  Read the article

• RHEL server Yum dependencies not working

  - by Tony

  I have a redhat server that isnt resolving dependencies correctly. I want to install httpd via yum "yum install httpd" and it installs correctly, but when i go to start httpd I get the following error: /sbin/service httpd restart Stopping httpd: [FAILED] Starting httpd: /usr/sbin/httpd: error while loading shared libraries: libaprutil-1.so.0: cannot open shared object file: No such file or directory [FAILED] It is missing the dependency for apr-util package. Weirdly the i386 package is installed and not the x86_64 package. Can anyone shed any light on why the dependencies might not be resolved correctly? ldd /usr/sbin/httpd libm.so.6 => /lib64/libm.so.6 (0x00002b02370db000) libpcre.so.0 => /lib64/libpcre.so.0 (0x00002b023735e000) libselinux.so.1 => /lib64/libselinux.so.1 (0x00002b023757a000) libaprutil-1.so.0 => not found libcrypt.so.1 => /lib64/libcrypt.so.1 (0x00002b0237793000) libldap-2.3.so.0 => /usr/lib64/libldap-2.3.so.0 (0x00002b02379cb000) liblber-2.3.so.0 => /usr/lib64/liblber-2.3.so.0 (0x00002b0237c06000) libdb-4.3.so => /lib64/libdb-4.3.so (0x00002b0237e14000) libexpat.so.0 => /lib64/libexpat.so.0 (0x00002b0238109000) libapr-1.so.0 => not found libpthread.so.0 => /lib64/libpthread.so.0 (0x00002b023832c000) libdl.so.2 => /lib64/libdl.so.2 (0x00002b0238547000) libc.so.6 => /lib64/libc.so.6 (0x00002b023874c000) libsepol.so.1 => /lib64/libsepol.so.1 (0x00002b0238aa3000) /lib64/ld-linux-x86-64.so.2 (0x00002b0236ebe000) libresolv.so.2 => /lib64/libresolv.so.2 (0x00002b0238ce9000) libsasl2.so.2 => /usr/lib64/libsasl2.so.2 (0x00002b0238eff000) libssl.so.6 => /lib64/libssl.so.6 (0x00002b0239118000) libcrypto.so.6 => /lib64/libcrypto.so.6 (0x00002b0239364000) libgssapi_krb5.so.2 => /usr/lib64/libgssapi_krb5.so.2 (0x00002b02396b6000) libkrb5.so.3 => /usr/lib64/libkrb5.so.3 (0x00002b02398e4000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x00002b0239b79000) libk5crypto.so.3 => /usr/lib64/libk5crypto.so.3 (0x00002b0239d7c000) libz.so.1 => /usr/lib64/libz.so.1 (0x00002b0239fa1000) libkrb5support.so.0 => /usr/lib64/libkrb5support.so.0 (0x00002b023a1b5000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x00002b023a3be000) yet this is the i386 package apr-util-1.2.7-11.el5.i386 : Apache Portable Runtime Utility library Repo : installed Matched from: Filename : /usr/lib/libaprutil-1.so.0

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• open-sshd service withou pam support !! How can I add pam support to sshd? Ubuntu

  - by marc.riera

  Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password

  Read the article

• Trust Bluetooth 4.0 and Bluetooth Headset

  - by Seregwethrin

  Firstly, I'm writing this after 5 hours of nonstop struggle to make it work, so I searched into the deepest websites from Google, and tried many things. I have Trust Bluetooth 4.0 USB adapter (link) Samsung HM1500 Bluetooth Headset Windows 7 64-bit Desktop PC Facts Nothing wrong with the headset. (it works, tested on a phone and a laptop. Problem is all about bluetooth dongle and its driver.) Trust BT adapter can send and receive files even without any driver. I can pair successfully without any driver too. In Headset's Properties, Services tab, Handsfree and Headset services are checked. Problem When I pair with my BT headset, I cannot see it as a sound playback device. Also when I double-click the headset device icon in Bluetooth Devices, in laptop: it opens a connection window where I can connect and disconnect to that device - perfect! in desktop: it opens the properties window, even though Handsfree and Headset services are checked (I check them explicitly, in laptop they came as already checked) - Problem! Unsuccessful driver installations The driver on the Trust's website says "Error 1606 Could not access Network Location" on start, so it doesn't get installed. The driver on Broadcom (link) is being closed with Windows's that classic "has stopped working" error on validation step, so it doesn't get installed too. (Those tests made more than once) Successful installation In the Win64 folder of Trust's driver from their website, if I install through "BTW.msi", it doesn't give me Error 1606 and it gets installed. Then the problem: When I try to start bluetooth from start menu (or it gets started at Windows startup), an error popup says: "BtBalloon.dll is missing..." so it doesn't start. I found BBalloon.dll in the driver folder, I renamed it to BtBalloon.dll, moved into Windows/system32 and Windows/SysWOW64 folders, and it seems working. Or maybe it gets closed behind the scenes. The bluetooth icon is there with or without this driver since Windows has it. Bluetooth Peripheral Device First it didn't get installed from Windows Update. After, I showed the driver folder path in Device Manager and pressed "Explore in this location". Surprisingly, it's being found as "Handsfree" driver. Now even I uninstall the drivers, it still can see the Handsfree. But still, no playback device. Any ideas to guide me? I'm out of ideas.

  Read the article

• iTunes Title Bar is Equal to the Location of the Library file?

  - by Urda

  I have never been able to get a clear answer on why the latest edition of iTunes does this. I have my entire iTunes library located in C:\itunes\ and the library data files inside C:\itunes\!library_info for backup purposes. However when version 9 of iTunes came out it went from having iTunes as the title, to !library_info. Anyway to get around this without moving my data files away? Annoying "feature" if that is what it is. Again Apple support and forums were of no help to me. Anyone have insight on this? System Info: Windows Vista x86 Ultimate, latest updates. iTunes Version 9.0.3.15 Screenshot: http://farm5.static.flickr.com/4072/4414557544_d0b25eb64c_o.jpg Flickr Page: http://www.flickr.com/photos/urda/4414557544/

  Read the article

• Windows 7 File Associations .mov

  - by Paul Mung

  I created a new windows 7 SP1 base image. Everything is all fine and dandy with that. So i am now installing standard applications I would like Quicktime to manage .mov files. The only problem is WMP (Windows Media Player) won't give up the association to .mov files. It's driving me crazy... i've been reading threads on how to fix file associations. I would like to do it via registry, powershell or cmdline. I cannot use GPO I've tried the following: assoc .mov=QuickTime.mov ftype QuickTime.mov="%ProgramFiles(x86)\QuickTime\QuickTimePlayer.exe" Reg add HKCU\Software\Microsoft\windows\CurrentVersion\Explorere\FileExts\.mov\UserChoice" /v Progid /d QuickTime.mov /f Reg add HKCU\Software\Microsoft\windows\CurrentVersion\Explorere\FileExts\.mov\OpenWithList" /v a /d QuickTimePlayer.exe /f Reg add "HKCU\Software\Microsoft\windows\CurrentVersion\Explorere\FileExts\.mov\OpenWithList" /v b /d wmplayer.exe /f Reg add HKCU\Software\Microsoft\windows\CurrentVersion\Explorere\FileExts\.mov\OpenWithList" /v MRUList /d ab /f Reg add HKCU\Software\Microsoft\windows\CurrentVersion\Explorere\FileExts\.mov\OpenWithProgids" /v Quicktime.mov /t REG_NONE /d 0000 /f Reg add HKCU\Software\Microsoft\windows\CurrentVersion\Explorere\FileExts\.mov\OpenWithProgids" /v WMP11.AssocFile.MOV /t REG_NONE /d 0000 /f

  Read the article

• Optimal setup for ASUS P6X58D Premium BIOS (no OC)?

  - by rumtscho

  Normally, I'd trust the mainboard manufacturer to choose the best options as defaults. But I had trouble with the board, because even with Quick Boot enabled, it booted twice as slowly as a Pentium 4 Celeron. Then I changed lots of options at once (most of them weren't explained in the manual, just mentioned with a single sentence) and the boot time is only marginally worse than the Pentium 4 (54 sec against 46 sec from button to pw entering screen). Now I don't know if I have turned something off which should have stayed on. I guess I even won't be able to boot from a CD now, because even though it is present in the boot sequence, I took off a timeout I think it needs to check whether there is a disk in the drive. The second reason is that I don't have an internal HDD, only a SSD. I forgot my sources blush but I am under the impression that today's BIOS and OS options are geared toward booting from a HDD, which is often less than optimal when one boots from a SSD, especially when there are functions which cause avoidable writing cycles, as a SSD wears out after too many writing cycles. Most of the things I've read concern the OS, but there are some BIOS-relevant options too. I am especially confused about the disk mode. The board supports AHCI, IDE-simulation and RAID, but of the different articles I've read, there is a proponent for each and no clear arguments for any. So can one tell me which options are important in general and which are important for a SSD-only system? I don't want to overclock the CPU, so you don't have to say anything about this (yes I know the board is meant for OC:)). I am thinking of overclocking the RAM, since they sold me 1600er heatsinked modules which are running at 1066 now, but I'm not sure yet about that. The rest of the system: i7-930, Intel X25-m G2, 6 GB RAM, GTS 250, some no-name Blue-ray ROM. 2 external HDDs over USB 2.0. Lots of other USB-connected hardware (12 devices I think), no SATA 3 drives (will disabling the controller have an impact on performance?), no LAN, only WiFi. Lucid Lynx 64 bit, no dual boot, no virtual installations. The main uses of the system are: managing and playing/showing all the media stored on the external disks, lots of image manipulation, some video editing, a bit of (non-demanding) gaming, rarely development. Lots of Internet surfing too, but this shouldn't have much impact on performance.

  Read the article

• Why my laptop doesnt boot in any OS (windows or ubuntu) after RAM upgrade?

  - by qrsq

  My laptop previously had 2 slots of RAM ( 1x1Gb , 1x2GB , both were clocked at 1066mhz) and it was working on windows 7 x86 OS. I Upgraded the ram with ( 2x4GB clcoked at 1333mhz). Bios displayed 8192MB of memory and windows was working ok but (only 2.99GB of ram from 8gb was avabile). So i decided to switch to an x64 system to be able to use all the amount of memory. But the laptop wasnt able to install any os (windows 7 x64 or windows 8 x64) so i placed the 3gb of ram instead of 8gb. Then i succesfully instaled an x64 os (windows 8). After than i placed the 8gb ram back again. Now the computer doesnt boot in the os but bios is working normally. I tried also to install ubuntu , without any succes. What should i do ?? All the help will be appreciated. thanks

  Read the article

• Multiple PXE boots on the same subnet for RIS and WDS

  - by Tim

  We are looking to migrate off our existing server 2003 sp2 machine, running RIS (which I know is WDS as of Server 2003 Sp2, but to be clear..) with a bunch of legacy RiSETUP images to a Server 2008 r2 box. Because the change in architecture (x86 to x64), and a limitation of the Server 2008 upgrade path that won't allow mixed-mode WDS services to be upgraded, I am forced to look at running Server 2003 for RIS and Server 2008 R2 for WDS for Windows 7 on the same network. The problem I'm facing is how to deal with both PXE services at the same time? I'd still like the existing RIS server to be available for production use, but start working on WDS for deploying Windows 7. Is there a way to have a sort of PXE "chooser" ? Or some other mechanism to be able to select which server the client should download the boot image from? Thanks!

  Read the article

• Mongodb: why is my mongo server using two PID's?

  - by Lucas

  I started my mongo with the following command: [lucas@ecoinstance]~/node/nodetest2$ sudo mongod --dbpath /home/lucas/node/nodetest2/data 2014-06-07T08:46:30.507+0000 [initandlisten] MongoDB starting : pid=6409 port=27017 dbpat h=/home/lucas/node/nodetest2/data 64-bit host=ecoinstance 2014-06-07T08:46:30.508+0000 [initandlisten] db version v2.6.1 2014-06-07T08:46:30.508+0000 [initandlisten] git version: 4b95b086d2374bdcfcdf2249272fb55 2c9c726e8 2014-06-07T08:46:30.508+0000 [initandlisten] build info: Linux build14.nj1.10gen.cc 2.6.3 2-431.3.1.el6.x86_64 #1 SMP Fri Jan 3 21:39:27 UTC 2014 x86_64 BOOST_LIB_VERSION=1_49 2014-06-07T08:46:30.509+0000 [initandlisten] allocator: tcmalloc 2014-06-07T08:46:30.509+0000 [initandlisten] options: { storage: { dbPath: "/home/lucas/n ode/nodetest2/data" } } 2014-06-07T08:46:30.520+0000 [initandlisten] journal dir=/home/lucas/node/nodetest2/data/ journal 2014-06-07T08:46:30.520+0000 [initandlisten] recover : no journal files present, no recov ery needed 2014-06-07T08:46:30.527+0000 [initandlisten] waiting for connections on port 27017 It appears to be working, as I can execute mongo and access the server. However, here are the process running mongo: [lucas@ecoinstance]~/node/testSite$ ps aux | grep mongo root 6540 0.0 0.2 33424 1664 pts/3 S+ 08:52 0:00 sudo mongod --dbpath /ho me/lucas/node/nodetest2/data root 6541 0.6 8.6 522140 52512 pts/3 Sl+ 08:52 0:00 mongod --dbpath /home/lu cas/node/nodetest2/data lucas 6554 0.0 0.1 7836 876 pts/4 S+ 08:52 0:00 grep mongo As you can see, there are two PID's for mongo. Before I ran sudo mongod --dbpath /home/lucas/node/nodetest2/data, there were none (besides the grep of course). How did my command spawn two PID's, and should I be concerned? Any suggestions or tips would be great. Additional Info In addition, I may have other issues that might suggest a cause. I tried running mongo with --fork --logpath /home/lucas..., but it did not work. More information below: [lucas@ecoinstance]~/node/nodetest2$ sudo mongod --dbpath /home/lucas/node/nodetest2/data --fork --logpath /home/lucas/node/nodetest2/data/ about to fork child process, waiting until server is ready for connections. forked process: 6578 ERROR: child process failed, exited with error number 1 [lucas@ecoinstance]~/node/nodetest2$ ls -l data/ total 163852 drwxr-xr-x 2 mongodb nogroup 4096 Jun 7 08:54 journal -rw------- 1 mongodb nogroup 67108864 Jun 7 08:52 local.0 -rw------- 1 mongodb nogroup 16777216 Jun 7 08:52 local.ns -rwxr-xr-x 1 mongodb nogroup 0 Jun 7 08:54 mongod.lock -rw------- 1 mongodb nogroup 67108864 Jun 7 02:08 nodetest1.0 -rw------- 1 mongodb nogroup 16777216 Jun 7 02:08 nodetest1.ns Also, my db path folder is not the original location. It was originally created under the default /var/lib/mongodb/ and moved to my local data folder. This was done after shutting down the server via /etc/init.d/mongod stop. I have a Debian Wheezy server, if it matters.

  Read the article

• Can't create a valid symlink under VMWare HGFS

  - by Alexander Gladysh

  Host: OS X 10.6.5 VMWare Fusion: 3.1.2 Guest: Ubuntu x86 10.10 $ uname -a Linux ubuntu 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 01:41:57 UTC 2010 i686 GNU/Linux I can not create a symlink, readable from the Guest OS anywhere in the directory, mounted with hgfs: /mnt/hgfs/projects/tmp$ touch aaa /mnt/hgfs/projects/tmp$ ln -s aaa bbb /mnt/hgfs/projects/tmp$ less bbb bbb: No such file or directory /mnt/hgfs/projects/tmp$ ls -la total 6 drwxr-xr-x 1 501 users 136 2010-12-28 18:12 . drwxr-xr-x 1 501 users 8602 2010-12-28 18:12 .. -rw-r--r-- 1 501 users 0 2010-12-28 18:12 aaa lrwxr-xr-x 1 501 users 3 2010-12-28 18:12 bbb - aaa /mnt/hgfs/projects/tmp$ readlink bbb aaa The same symlink is perfectly accessible in OS X host. Is there a workaround for this?

  Read the article

< Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >