Search Results

Search found 11734 results on 470 pages for 'refer to itself'.

Page 318/470 | < Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >

  • Cooling for a small server room

    - by John Zwinck
    I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

    Read the article

  • Apache2 process stuck at 100% cpu, CLOSE_WAIT socket lingering

    - by mmazing
    I've troubleshooted the heck out of this today, and I can't seem to find any information on how to determine what is happening exactly. Basically, on my development server, another developer is causing CLOSE_WAIT connections that eat up one or more apache2 processes for several hours if I don't restart apache2. strace on any of the processes yields no information, only that it was able to attach. mod_proxy is not enabled. KeepAlive is on, KeepAliveTimeout is 15 seconds, MaxKeepAliveRequests is 100. From what I've been reading, this may or may not be an apache issue at all, just that that's how CLOSE_WAIT works (the server is waiting for a FIN packet to close the connection). I just can't believe that a server would be crippled so easily by not receiving a packet from a remote host telling it to close the connection. Especially without any intervention for well over an hour. Any tips? I'm about to pull my hair out. Edit : Also, there are no unusual entries in any apache log files. Edit 2: lsof -i shows only a single CLOSE_WAIT per hanging process. (That's what has been bothering me about this, as most other discussions talk about many CLOSE_WAIT connections, while I only have one per process.) The nature of the code that is running (php) doesn't really lend itself to closing open connections and whatnot. I can run the same code that he is executing with the same session data, and not result in a hanging process.

    Read the article

  • Are there any wireless webcams/cameras that Windows will recognize as a capture device?

    - by Keithius
    I'd like to have a webcam in a different room from my computer, and the distance means USB is out of the question. I know there are many wireless cameras, but what I can't seem to find out is if any of them would be recognized by Windows as a capture device (just like a locally connected USB webcam). Most of the wireless cameras I can find (e.g., D-Link DCS920; Cisco-Linksys WVC54GCA, etc.) can all stream video directly from the camera itself, which is fine if you're using the camera as a "security" camera (for private use only), but not for other uses (say, sending the video to an online video streaming service, e.g., Ustream). It seems like this should be possible; after all, wireless (WiFi) printers with scanners are recognized by Windows. Are there any wireless (WiFi) cameras out there that would be recognized by Windows as a capture device in the same way as a USB webcam would? Alternatively, a camera that's not wireless (e.g., connects via Ethernet) would do the trick too - but I imagine if anyone is going to make a remote camera like this, they'd go the extra step and make it wireless, too.

    Read the article

  • Drive Mapped On Amazon EC2 Instance Startup Disconnected After Logon

    - by jsn
    I am launching an Amazon EC2 instance (Windows Server 2012), and on startup (though User Data field), it runs this powershell script: <powershell> NET CONFIG SERVER /AUTODISCONNECT:-1 # clear all prior connections net use * /delete /y > C:\delLog.txt 2>&1 # mount new drive net use R: \\dbHost\share /user:username pass /persistent:yes > C:\useLog.txt 2>&1 ipconfig /all > C:\ipLog.txt </powershell> When it launches and I connect to it through RDP, it shows in explorer "Diconnected Network Drive (R:). If I double click it, error message displays "R:\ is not accesible. Access id denied". Normally, it would ask me for credentials to reconnect. I need for this drive to be connected through the duration of the instance. delLog.txt contents: You have these remote connections: T: \\dbHost\share Continuing will cancel the connections. The command completed successfully. useLog.txt contents: The command completed successfully. ipLog.txt contents as expected. The net use commands works fine by itself, it connects. Anyone have any idea what could be wrong? There is only one account on these machines - Administrator. It is a samba share to a Linux server on a private network.

    Read the article

  • How to connect a VM running on an ESXi host to that host via a VMKernel NIC?

    - by Zac B
    Say I have an ESXi (5.0) host that runs a Linux distribution which hosts iSCSI targets, which contain the images for other VMs which the host will run. When it's used, I'll start the host first, then the iSCSI server, and then refresh all storage targets/HBAs in order to see the provided shares as online. I know it's a strange puzzle-box solution, but I was told to implement it. The ESXi host itself has a gigabit NIC which connects to the outside world. The guest OS (CentOS) supports VMXNet3, however, and if I can, I'd like to use its VMXNET3 NIC to host iSCSI for the ESXi host. How should I go about doing this? I went to create a new virtual network, and selected "VKernel", as it suggested that I use that type of network for SAN traffic, but it is apparently not set up for "self-hosted" SAN hosts, as the new network did not appear as an option to attach the CentOS box's VMXNET3 NIC to. How should I best connect an iSCSI host out to its "parent" ESXi host, if I need a) a 10gb connection, and (optionally) b) a VMKernel network for it?

    Read the article

  • How to make Exchange 2003 non-authoritive

    - by Romski
    Background We are a small company with an internally hosted Exchange 2003. It receives email for 2 domains (the company was renamed a few years back). For the sake of argument, the domains are: oldname.com newname.com We have moved newname.com to a hosted exchange service, and our DNS record is correctly routing emails. Our internal server still receives email for oldname.com, although we have asked our hosting company to accept emails for that domain. Problem My problem is that emails generated internally from monitoring software, printer, etc. are being caught by our (defunct) internal server and being delivered to the old mailboxes. I believe that what is happening is that our internal exchange server considers itself to be the authoritive server for newname.com. I think it must be looking in active directory for a mailbox and delivering it internally without ever going outside. Attempt to fix I started to follow the article here: http://support.microsoft.com/kb/321721. I removed the SMTP recipient policy for newname.com, and added a dummy address and made it primary. I also answered yes for updating the associated emails. I then restarted the Microsoft Exchange Routing System and SMTP, but emails are still being routed internally. Is there a way to force the exchange server to route all emails for the domain newname.com to the new hosted service?

    Read the article

  • Streaming to PS3 with NAS and built-in dlna server?

    - by philt
    With consumer-grade hardware, is it possible to successfully stream 1080p mp4 videos to a PS3? I have a linksys router that can only do 10/100. The PS3 is wired to it with cat5e cable, and the PS3 itself supports gigabit ethernet. I would upgrade the router and get one that supports gigabit ethernet if it could handle streaming like this. It currently does work with minor jerkiness streaming from my mac to the PS3, but fast-forward/reverse and "goto" (equivalent of scene selection) take forever and/or fail completely. And streaming from my mac of course requires the mac to be on at all times. When I put the movies on an external USB drive and connect to the PS3 directly, it performs flawlessly. Fast forward and everything works great. So I was thinking about getting a NAS, but I don't know if any inexpensive NAS (i.e. Buffalo Linkstation Live, WD My Book World Edition, D-Link DNS-321, etc.) can actually deliver the performance necessary to do this, even with gigabit ethernet?

    Read the article

  • Finding cause of TCP retransmission within a LAN

    - by Surreal
    Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

    Read the article

  • Windows 7 UAC (user access control) is being disabled on every reboot

    - by Christian Thamer
    To put it simply, I noticed UAC was disabled so I enabled it. I was prompted to reboot the computer for the changes to take effect. Upon my reboot I checked the settings again as I hadn't disabled UAC in the first place. It was again set to off (never notify). For the heck of it I repeated the process a couple of more times. Same result each time. I have Microsoft Security Essentials running a full scan nightly so I should be protected from viruses. I also did an on demand scan with the online tool at www.antivirus.com. Nothing was found. Other than the fact that UAC is being disabled on each reboot I have no other reason to suspect a virus. So my question is does anyone have insight into if this is a possible problem with a virus or other malware changing my UAC settings on each boot or is it possibly a problem with Windows and UAC itself? If it is malware are there suggestions for other products outside of the ones I have used to detect and remove it.

    Read the article

  • Need assistance making a batch file for renaming files in separate folders

    - by Carnaxus
    Ok, here's one for you. I'm trying to use a batch file to rename a bunch of files, but none of them are in the same folder as the batch file itself. The command prompt keeps telling me that the directory can't be found. I suppose I could just rename all the files in all the folders that match the filename, but I don't want to do that either; I only want to change certain ones. My batch file as it stands is: @echo off ren "engine/info.txt" "disabled.txt" ren "gravplating/info.txt" "disabled.txt" ren "HAWX content/info.txt" "disabled.txt" ren "laserz/info.txt" "disabled.txt" ren "NeuroNaval/info.txt" "disabled.txt" ren "NeuroPlanes/info.txt" "disabled.txt" ren "NeuroTanks/info.txt" "disabled.txt" ren "NeuroWeapons/info.txt" "disabled.txt" ren "WAC Base/info.txt" "disabled.txt" ren "WAC DamageSystem/info.txt" "disabled.txt" ren "WAC GravityController/info.txt" "disabled.txt" ren "WAC Helicopters/info.txt" "disabled.txt" ren "WAC Sweps/info.txt" "disabled.txt" ren "weapons/info.txt" "disabled.txt" ren "AFF_ships/info.txt" "disabled.txt" ren "AntiTakeRifle/info.txt" "disabled.txt" ren "Catmull-Rom Cameras/info.txt" "disabled.txt" ren "Displacer Cannon/info.txt" "disabled.txt" ren "Drumdevil's Trains/info.txt" "disabled.txt" ren "EVEOnline/info.txt" "disabled.txt" ren "gm_botmap_v3/info.txt" "disabled.txt" ren "gm_construct_flatgrass_v5-2/info.txt" "disabled.txt" ren "gm_mobenix_v3_final/info.txt" "disabled.txt" ren "gm_mobenix_v3_highquality_Water/info.txt" "disabled.txt" ren "gm_snabbansairfield_b1/info.txt" "disabled.txt" ren "gm_XhS_construct/info.txt" "disabled.txt" ren "linedraw/info.txt" "disabled.txt" ren "ModelManipulator/info.txt" "disabled.txt" ren "NeuroCars/info.txt" "disabled.txt" ren "Propeller Engine/info.txt" "disabled.txt" ren "VanDookie and Predaaator's pack/info.txt" "disabled.txt" ren "WAC ECM/info.txt" "disabled.txt" ren "WAC Extra Helicopters/info.txt" "disabled.txt" echo Done! pause

    Read the article

  • SharePoint Search: processing filenames containing underscores

    - by Todd Owen
    We use SharePoint Server 2007 to allow employees to search network file shares, but it seems that underscores in filenames are not treated as word separators when indexing the files. As a result, a search for chocolate will: match "chocolate milkshake.doc" but not match "chocolate_cake.doc" (Of course, this is a simplified example; in practice the content of the second file might include the word "chocolate" and match on that instead of the filename. But the problem itself is real enough, because a common scenario in a corporate environment is that a user knows the the partial name of the file they are looking for and expects to see matching filenames at the top of the search results. And using underscores in filenames is a widely used convention within our company). Underscores are not treated as word separators in the file content either, although this is less of a concern for us. The root cause of this problem is possibly related to the behaviour of the word breakers that SharePoint uses (i.e. the language-specific DLLs that implement the IWorkBreaker interface), although I haven't confirmed this yet. Does anyone know of a workaround for this issue? I have tested with Search Server 2008 Express too (which is based on the same technology), and it is also affected. I do not know whether the problem is fixed in SharePoint 2010 or not.

    Read the article

  • Secondary backup server

    - by verdy
    I've been given a task to implement a backup solution in the event of our website goes down. It is a dedicated server running centos 6. From what i've experience on our server, our server may go down because of PHP application crash or hardware failure. I have couple of questions: In the first case, is it possible to get the server restart the PHP automatically, how can I do that? Because in my mind, if it is only the application that goes down, probably I can still make use of the server itself. In the second case, can I redirect a request to a secondary server? How can I do that? What do I need other than another server? For now it is gonna be a simple server which shows the user a static landing page so later the system notify us via email that the primary server went down so that we can restart the server manually. Is it possible to setup just a vps or even a shared server for the secondary server ? As I think there is only gonna be a static page. Thanks. Any help would be much appreciated

    Read the article

  • iis7 large worker process request queue creating process blocking aspnet.config & machine.config amended (bottleneck)

    - by scott_lotus
    ASP.net 2.0 app .net 2.0 framework IIS7 I am seeing a large queue of "requests" appear under the "worker process" option. State recorded appear to be Authenticate Request and Execute Request Handles more than anything else. I have amended aspnet.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727 (32 bit path and 64 bit path) to include: maxConcurrentRequestsPerCPU="50000" maxConcurrentThreadsPerCPU="0" requestQueueLimit="50000" I have amended machine.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727\CONFIG (32 bit and 64 bit path) to include: autoConfig="true" maxIoThreads="100" maxWorkerThreads="100" minIoThreads="50" minWorkerThreads="50" minFreeThreads="176" minLocalRequestFreeThreads="152" Still i get the issue. The issue manifestes itself as a large number of processes in the Worker Process queue. Number of current connections to the website display 500 when this issue occurs. I dont think i have seen concurrent connections over 500 without this issue occurring. Web application slows as the request block. Refreshing the app pool resolves for a while (as expected) as the load is spread between the two pools. Application pool in question FIXED REQUEST have been set to refresh on 50000. Thank you for any help. Scott quick edit to say hmm, my develeopers are telling me the project was built with .net 3.5 framework. Looking at C:\Windows\Microsoft.NET\Framework64\v3.5 there does not appear to be a ASPNET.CONFIG or a MACHINE.CONFIG .... is there a 3.5 equivalent ? after a little searching apparenetly 3.5 uses the 2.0 framework files that 3.5 is missing. So back to the original question , where is my bottleneck ?

    Read the article

  • Maxtor 500GB external hard drive not being detected but power is going to it?

    - by ClarkeyBoy
    I have 2 * Maxtor Onetouch 4 Lite 500GB external hard drives (part no. 9NT2A4-500). They both used to work fine on my old laptop (an Acer) but I have not used them for about a year, since my laptop was stolen and I got this one (also an Acer [Aspire 7738G]). I have one plugged into the mains with one of the leads I believe was supplied with them. It appears to be receiving power as it is warm and the power light (on the unit itself) is on; also the mains adapter is fairly warm. I also have it plugged into my laptop with a USB lead which I have tested on my mp3 player (so I know it works). However my hard drive is not showing on my computer. I have tried checking for new hardware, installing the software that was supplied with it, checking drive letters in case it is registered as C: or something stupid, checking for problems etc... I can't find any cause for it to do this. It does appear to be starting up and, possibly, shutting down and restarting constantly (that's what it sounds like altho I can't be certain). I have had both hard drives stored in different places for the last year and they're both doing the same thing.. if it was only one then I'd guess it had got damaged or corrupted or something but since it is both I doubt this is it. The only things in common with both of them are the leads and the laptop, however I know the USB lead works and guess the mains lead works as there is power going to the unit. Has anyone come across this before or does anyone have any idea what the cause / solution to the problem is? Any help would be greatly appreciated. Regards, Richard

    Read the article

  • Kubuntu: apt-get install of php5-dev: libtool version mismatch?

    - by pinkgothic
    (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

    Read the article

  • Kubuntu: apt-get install of php5-dev: libtool version mismatch?

    - by pinkgothic
    (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

    Read the article

  • IIS7 error config and remote errors

    - by Kev
    Certain IIS7/7.5 500.19 configuration errors only render on a browser running on the local server. This appears to happen regardless of whether I set <httpErrors errorMode="Detailed" existingResponse="PassThrough" /> in the system.webServer section of a site's web.config file (or even globally for that matter). For example, I had a developer who reported that he was just getting the generic IIS7 500 error page: This was happening even though he had the following configured in his web.config: <configuration> <system.webServer> <httpErrors errorMode="Detailed" existingResponse="PassThrough" /> </system.webServer> </configuration> If I browse to the site on the server itself I see (some sensitive info redacted): Would the reason for this be that if the web.config has errors it therefore can't be parsed. Because it can't be parsed the local <httpErrors> setting doesn't get read and thus causes IIS to revert to default settings (i.e. DetailedLocalOnly)? Update: @LazyOne - suggested setting the above config at the server level which I already tried. This resulted in just raw 500 errors:

    Read the article

  • Encryption setup for Linux NAS?

    - by Daniel
    There's a bazillion hard disk encryption HOWTOs, but somehow I can't find one that actually does what I want. Which is: I have a home NAS running Ubuntu, which is being accessed by a Linux and a Win XP client. (Hopefully MacOS X soon...) I want to setup encryption for home dirs on the NAS so that: It does not interfere with the boot process (since the NAS it tucked away in a cupboard), the home dirs should be accessible as a regular file system on the client(s) (e.g. via SMB), it is easy to use by 'normal' people, (so it does not require SSH-ing to the NAS, mount the encrypted partition on command line, then connecting via SMB, and finally umount the partition after being done. I can't explain that to my mom, or in fact to anyone.) does not store the encryption key the NAS itself, encrypts file meta-data and content (i.e. safe against the 'RIAA' attack, where an intruder should not be able to identify which songs are in your MP3 collection). What I hoped to do was use Samba + PAM. The idea was that on connecting to the SMB server, I'd have to enter the password on the client, which sends it to the server for authentication, which would use the password to mount the encrpytion partition, and would unmount it again when the session was closed. Turns out that doesn't really work, because SMB does not transmit the password in the plain and hence I can't configure PAM to use the incoming password to mount the encrypted patition. So... anything I'm overlooking? Is there any way in which I can use the password entered on the client (e.g. on SMB connect) to initiate mounting the encrypted dir on the server?

    Read the article

  • Robocopy launches and then hangs/just sits there

    - by NateO
    I'm setting up an archive process to store old files on an external hard drive. The computer in question is running Windows 7 Pro 32bit. We have a server folder with 150,000+ files in it, most of which are pretty small (below 200k). I'm trying to use robocopy in a batch file to do this. It was working fine the other day, now all it does upon launch is sit there. It shows me all the options and whatnot, and also lists the number of files in the directory and the directory itself, but it never gets past that line. If I switch the destination to the local C drive, it eventually starts copying files. Is there something in my batch file that needs to change? Or could there be a problem with the external Western Digital drive that I'm using? The WD drive currently is holding about 175,000 files. Here is the one line batch file I have: robocopy "\\cgifp01\Prepress\Public\ImportedPDF" "E:\OldFiles" *.* /R:2 /W:10 /MINAGE:15 /MOV /B /XJ /XF "blank_test.pdf" Thanks for any tips or ideas. Nate

    Read the article

  • IIS Manager - Connect to Another Server (Win7 to Win2008 server)

    - by Matt
    I am running Windows 7 Ultimate. If I open up IIS Manager, I see a list of "connections" on the left hand side. In previous versions, I would be able to select an option to "connect to another server" or "connect to another machine", but there is no such option visible anywhere here. The only thing in the list is my local machine. Even in the address bar, if I manually type in the server location (\servername, even tried just servername), nothing happens (it just reverts back to my current local computer) The documentation at http://technet.microsoft.com/en-us/library/cc732466%28WS.10%29.aspx seems to imply the very same steps... but there is just no button or menu option anywhere to do this. Am I missing something? I'm not even seeing a grayed out menu option. EDIT: Under the "File" menu, I see 2 options: Save Connections (grayed out) Exit Under the "Connections" pane, I see 1 button, grayed out. When I hover the mouse, it simply says "Up", appears to be usable if I browse into an element in my local computers IIS settings If I right click inside the pane itself, I see Refresh Add website (to the current host) Start Stop Rename Switch to Content View UPDATE: I downloaded and installed the Remote Server Administration tools from http://www.microsoft.com/downloads/details.aspx?FamilyID=7D2F6AD7-656B-4313-A005-4E344E43997D&displaylang=en, and I enabled everything listed under "Remote Server Administration Tools" under "Turn Windows Features On or Off". Still nothing.

    Read the article

  • Google chrome not accepting any security certificates

    - by Jerry
    I've recently developed a problem with Google Chrome that's really annoying. I'm using Firefox at the moment with no problems whatsoever and it's the same with IE, so it's safe to say this problem is specific to Chrome. The problem is that it's not accepting security certificates from certain sites. I suppose the best place to start would be google itself. I can't search. The google search page will load but when I type some search term into the search box and hit 'search' I get the message: "You attempted to reach www.google.com, but the server presented an invalid certificate. You cannot proceed because the website operator has requested heightened security for this domain." No matter what the search term is, this is the result. Also when I try to log in to facebook - same message. Youtube works and many other sites that I know present security certs so I'm baffled. I've searched and there are other people who have had similar issues but I can't find a solution anywhere. The most common answer I'm picking up for this is to "check your system time" but I can safely say that it's not my system time. If anyone knows what is going on, I'd very much appreciate being informed. It's not super urgent as I can use Firefox to access those places Chrome won't, but it IS super annoying because I can usually sort out issues like this in no time.

    Read the article

  • Forward Apache to Django dev server

    - by Alex Jillard
    I'm trying to get apache to forward all requests on port 80 to 127.0.0.1:8000, which is where the django dev server runs. I think I have it forwarding properly, but there must be an issue with 127.0.0.1:8000 not being run by apache? I'm running the django dev server in an ubuntu vmware instance, and I'd other people in the office to see the apps in development without having to promote anything to our actual dev/staging servers. Right now the virtual machine picks up an IP for itself, and when I point a browser to that url with the defualt apache config, I get the default apache page. I've since changed the httpd.conf file to the following to try and get it to forward the requests to the django dev server: ServerName localhost <Proxy *> Order deny,allow Allow from all </Proxy> <VirtualHost *> ServerName localhost ServerAdmin [email protected] ProxyRequests off ProxyPass * http://127.0.0.1:8000 </VirtualHost> All I get are 404s with this, and in error.log I get the following (192.168.1.101 is the IP of my computer 192.168.1.142 is the IP of the virtual machine): [Mon Mar 08 08:42:30 2010] [error] [client 192.168.1.101] File does not exist: /htdocs

    Read the article

  • some windows 8 metro (modern UI) apps don't open, but live tiles DO work

    - by DiegoDD
    Some of my default windows 8 metro (modern UI) apps don't work properly, the apps are the Weather and the News apps. when I open them, I only get the loading screen, that is, the big colorful screen with the logo in the center, and the "loading" spinning dots. They just keep like that forever and never actually open. There are no error messages or anything. The strange this is that the live tiles for those apps DO work and show current information. current weather for my location (saved before they started failing) and current news. Both apps did work well in the past, and every other default windows 8 app I've tried work well (both live tiles and the app itself). Every other non-default apps that I've downloaded still work correctly, so the problem so far is only with those two apps. (weather and news). I really don't know since when exactly they started to fail because I really don't use them (or any metro app) that often, so I can't recall if I did something like installing some other app, either metro or regular, or messed with some drivers, etc. they simply don't open now, but they DID work before. any ideas?

    Read the article

  • Mac Mini drive problems but SMART verified: bad hard drive or controller?

    - by Zac Thompson
    I have a 3-year-old Intel Mac Mini at home. About a month ago, it stopped booting from the hard drive (internal, SATA, 80GB). I tried booting from the Install Disc to repair the filesystem but Disk Utility was unable to do so ("invalid node structure"). I was also unable to use the hard drive in the Terminal from the Install Disc nor from an Ubuntu boot CD ("DRDY err"). I could see the contents of some directories, but others would give an error and I would get failures when trying to copy files. At this point I was sure the filesystem was hosed and I'd want to reformat at least. DiskWarrior was able to let me retrieve the data files I was interested in, which are now copied to an external hard drive, but it reported a high number of problems ("speed reduced by disk malfunction" count was over 2000) when in the process of trying to rebuild the directory for the drive. It also would not let me use the rebuilt directory to replace the one on the drive; it claimed the disk errors prevented recovery in this way. Under normal circumstances I would now assume that the drive itself was going bad: DiskWarrior's "disk malfunction" error above is supposed to imply hardware problems. My initial plan was to buy a replacement for the internal 2.5" drive. However: Disk Utility, command-line tools and DiskWarrior had reported all along that the SMART status of the drive was okay/Verified. So I'm now worried that the drive hardware is actually fine, and that the problems were due to a disk controller that has gone "bad" somehow. If this is the case, I'll probably just replace the whole computer. Any advice on how I can tell what is to blame? I don't have a lot of extra hardware sitting around, so I don't have the option of simply dropping the drive in another machine or popping another hard drive inside the Mini.

    Read the article

  • Driver issue for 7850 HD Diamond Windows 7

    - by Mr.Student
    I have an issue with windows 7 implementing the drivers ati provides for my 7850 HD Diamond video card. The video card is plugged in correctly to the PCIE 2.0 slots of my motherboard (p6t asus) with more then enough power. Fortunately the card works as I have my monitor plugged into the card itself and I can see just fine. However windows 7 does not replace the standard vga default microsoft driver with catalyst drivers that I've tried installing from online as well as the CD. Every time I install the drivers using Catalyst Install manager it always finishes with "Install complete(Warnings occured)". I then see the warnings it has which it instead reports that it successfully installed the SDK, Catalyst Install Manager, and HDMI/AUDIO packages. When I check my device manager after that, the display adapter still shows as standard vga and that its still using microsoft default display adapter. Now this current card is replacing an old card of mine which is the ATI 4890 HD which works beautifully. In fact for the old card to work, all I need to do is go to device manager and right click on standard vga - click update driver and windows 7 magically finds the correct driver to install and everything is good. Not so with the new card. I've even went into my regedits and uninstalled every bit of ati driver software before reinstalling my new card. Nothing's worked thus far. I've already exchanged my card out once and talked to customer support from my motherboard, microsoft, and ati all blaming the other. Please help me out!!

    Read the article

< Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >