Search Results

Search found 8755 results on 351 pages for 'triple boot'.

Page 318/351 | < Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >

• Disaster After Removing Two HDD From LaCie RAID 0 Case

  - by John

  This is the second time this has happened. I own a LaCie IDE RAID 0 Enclosure and the RAID went bad. The system gave me a warning that the data could be read from the RAID but that nothing could be written, and to remove the data ASAP. I did that and erased and reinitialized the RAID. System reported it was fine, no issues. I wrote to the RAID again and the system reported the same issue. So, I removed the drives and tested them individually thinking one must have gone bad. Sure enough, one HDD reported all bad blocks, every single one after the Master Boot Record. I didn't think much about it because of the age of the drives, 5 years old. So, I bought two new drives plugged them in and started up the RAID again. Exactly the same thing happened. All was fine after initializing the RAID and then the next day after powering on the RAID the exact same issue. The HDD sitting in the same position as the first "bad" HDD reported all bad blocks. Obviously, this is an issue with LaCie's bridge board not with the drives. No utility I have used has been able to bring this HDD back to life. I thought I would just copy the MBR from the good drive to the new one using a sector editor but am hesitant. Is it possible the firmware on the HDD has been corrupted by the LaCie bridge board?? What else could be the cause of such an issue? How can I fix this drive?

  Read the article

• Why would my HDD main partition suddenly become hidden?

  - by Luis Oscar

  A few days ago I was using my computer as usual and I turned it off. The next day it wouldn't boot up. It just stayed after the hardware diagnostic window on the intermittent underscore screen. So clearly It wasn't booting up. I tried turning it on and off a couple of times with no avail. Finally I used windows 7 disk and it seemed as if there was no HDD. not even the installation would see the HDD. So i thought it was dead, i bought a new one installed it with windows and used a external case with the old HDD. plug it in and still couldn't see it. I finally downloaded a partition program EASUS or something and my HDD was there listed WITHOUT a system letter. I could however explore it and i set it as Unhidden and it came back to life. I could see it normally. I really just wish someone could explain to me what happened here, was it a virus? does it means the HDD is about to die? How can i prevent this or what should I do now? should i stop using this OLD HDD? Thanks

  Read the article

• Configuring WPA WiFi in Ubuntu 10.10

  - by sma

  I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• Xen networking is inconsistent in multiple ways

  - by WildVelociraptor

  I've been running xen for a few weeks now on an Ubuntu 12.04 server. I've got 3 guests: a Windows Server 2003 guest, an Ubuntu guest, and a Windows 7 Guest. My Server 2003 guest seems to work fine; I can ping it from the network, the hostname resolves correctly, and it can see the internet. This guest is attached to xenbr0, and its IP is 10.100.1.21. My Win7 guest is what is driving me crazy. I use the same configuration script as a base, changing the important parts (hostname and boot disk, mainly). It installed correctly, and is currently running, but I am unable to ping this guest. It's hostname is "alexander", with an IP of 10.100.1.22. It is also using xenbr0. The guest can ping the firewall and various IP addressess, but seems unable to resolve hostnames. Now heres the weird part: when I use rdesktop (RDP client) from my laptop (not the xen host) to connect to alexander, it works just fine. It apparently resolves the hostname fine, and does the same with the IP address. So, can someone tell me why I can access this guest using RDP, but not using ping, nslookup, traceroute, etc? It's apparently invisible to all but RDP. Also, is it okay to use two guests on the same bridge, or do i need different ones for each guest? Thanks in advance for any help. Regards

  Read the article

• Ubuntu 10.04 - Add RAID 1 Array?

  - by N Rahl

  I have an existing Ubuntu 10.04 desktop system setup and running on a hard drive (Drive A). I'd like to add 2 more hard drives (Drives B & C, same size) to the system and mount them as a RAID 1 array. How do I do that? I know how to create RAID arrays during the installation, but I don't want to reinstall my system, and I shouldn't have to since my system files will stay on their own drive separate from the RAID array. I've physically added both drives to the system, and formatted them as EXT3 with gparted. Ubuntu's disk utility has a "create raid" option, but it won't let me select any of my drives (it thinks they're all full). I don't mind using mdadm, but I've found several guides that are old, and give conflicting advice. Some say I have to edit an /etc/raidtab file, some say this is done automatically. So what's the current (Ubuntu 10.04) preferred way of adding a RAID 1 to an existing system? It should turn into a raid at boot, and mount itself in /home/myname/files/. Thanks!

  Read the article

• Toshiba Satellite U500 - Totally Damaged LCD

  - by ivan

  I accidentally damaged my Toshiba Satellite U500 laptop which resulted in a totally unusable LCD. The LCD panel has some cracks on it, and I can only see black & white spots; the laptop frame became broken/bent to where I can partially see inside the PC; the accident disassembled the CD tray, and bent the keyboard frame (which now has a weird hump). The system is still working though. It responds to my inputs (eg, turning it on/off, typing my password @ Windows Login, etc). What I want to do now is to transfer all of my important data from that laptop to my external drive. But I don't know how since the LCD screen is unreadable. I know I can connect it to an external monitor or a TV (I have a Samsung 1080p TV) but I don't know how. What cable should I purchase to connect the TV? Which ports on the laptop and TV should I connect it to? Do I need press something while/after connecting it? Can I boot my laptop using the TV?

  Read the article

• RAID 5 Install on Ubuntu Server 12.04 [closed]

  - by tarabyte

  Environment: Ubuntu Server 12.04, installing from bootable flash drive Error: No root file system is defined. Please correct this from the partitioning menu. I'm trying to set up a personal file server with software RAID 5. I just got three hard drives for this, but haven't found any solid documentation. I'm unsure what the basic way to partition my hard drives is. Can someone upload a screenshot of their "partition disks" screen so that I can compare with mine (attached)? Should I set the bootable flag? Do I need a /home partition? A /boot partition? Should I "Use [my partition] as: Ext4 journaling file system"? Or make that field "physical volume for RAID"? I am an engineer, but I have only a cursory knowledge of all-things-linux. If you know of any good learning resources I'd be happy to hear about those too (that way I don't have to blindly follow deprecated tutorials online). well, image would be here but i don't have a high enough reputation yet (please vote up :)) Thank you, References I've looked into: https://help.ubuntu.com/community/Installation/SoftwareRAID https://help.ubuntu.com/12.04/serverguide/advanced-installation.html http://forevergeeks.com/setup-ubuntu-server-with-raid-5/

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

• two computers on same network cannot ping eachother nor view NetBios resources

  - by slava

  I'd like to find out the problem of my network configuration I have network configuration is like in this diagram: The problem is between laptop1 and laptop2. At first I thought it was samba server problem. I was configuring samba server on one of the laptops and I wasn't able to access the shares from the second laptop no matter what I was doing. After installing/removing/configuring samba-server a couple of times I realized that the problem resides somewhere else. Laptop configurations: - Laptop1: ubuntu 12.04 - Laptop2: Windows 7/ ubuntu 12.04 ( dual boot ) - Server : ubuntu 12.04 When I do "ping 192.168.0.10" from laptop2, I get "Destination host unreachable". The same situation is when I ping in other direction. When I access Laptop1 shares from Laptop2, having windows 7 loaded, I get the error message: "Error code: 0x80070035 The network path was not found." When I ping "server" or "router" or "wifi router" from any of laptops I get a reply. The same with windows shares, I am able to access "server"s shares from Windows and Ubuntu, from any of my laptops. Netbios can't function correctly, that's obvious, I am unable to access windows shares between laptops. I assume that on "wifi router" is a miss-configuration, but I can't find what specifically. The "Wifi router" works as Hub + wifi, it is connected to "router" not in WAN port but in LAN1. Please, help me correctly configure the router to make them see each-other, or at least make NetBios work correctly, between laptops, to be able to access windows shares. Thanks!

  Read the article

• compile kernel 2.6.34 for Ubuntu Lucid for xen dom0 / pvops

  - by andreash

  Hi there, I'd like to compile a recent Linux kernel (2.6.34) for my Ubuntu 10.04 Lucid Lynx AMD64 box, mainly because I'd like to use it as a dom0 kernel with the recent xen4. There's plenty documentation on the web about how to compile a kernel 'Debian style'. But what I think would be nice to start with an 'official' Ubuntu config to be sure not to miss any important things and having to recompile over and over again. So what I'd like to do is compile 2.6.34, but starting with the 'official' /boot/config-2.6.32-XX from Ubuntu Lucid. The question is: How do I best do that? If I just take the config from 2.6.32, the new features from 2.6.33/34 won't be in the config. So what I'd like to do is somehow the 2.6.34 config with the original 2.6.32 one from Ubuntu. How can I best do that? Does it even make sense? Is there easier ways to achieve what I want? Thanks for your insight! A. PS: I just found a linux-image-2.6.32-bpo.4-xen-amd64 package on backports.org, but no information about it. Would it work as a dom0 kernel on Lucid?

  Read the article

• Rebinding Keys on a Dell Keyboard

  - by Maarx

  I have a Dell Multimedia Keyboard, similar to this one: It has many non-standard keys, like the small circular ones across the top, and the "Multimedia" keys above INSERT/HOME/PAGE_UP. They can be rebound through simple registry entries. Some sample ones are included below: [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey] [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\15] "ShellExecute"="C:\\Program Files (x86)\\Mozilla Firefox\\firefox.exe http://mail.google.com/mail/#inbox" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\16] "Association"=".cda" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\17] "ShellExecute"="C:\\Windows\\System32\\SnippingTool.exe" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\18] "ShellExecute"="calc.exe" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\7] "Association"="http" I've rebound the "MAIL" key to, instead of booting Outlook, to booting Firefox directed at my G-Mail account. I've rebound the button that would normally open "MY COMPUTER" to instead boot the Windows 7 "Snipping Tool", something I find very useful. Now, I'm looking to do some other things that I don't already know how to do. Note that answering this question doesn't necessarily require any knowledge about the keyboard or rebinding the keys: I can add, for any given key, a "ShellExecute" entry, and it will simply execute the following command as if it was typed at a Command Prompt. (I'm aware I dumbed that down rather significantly, but bear with me. I'm not really a Windows guy myself.) I use the volume knob for it's intended purpose, to change volume. I would like to change, however, a different key, to "reset" the Windows volume level back to exactly 50%, or, as it refers to it, "50", on it's 0-100 scale. I'm looking for the "program" (what I would type at a command prompt? these are still just Sys32 programs in the PATH, aren't they?) that, I imagine, would take arguments, to change Sound/Volume settings under Windows 7. Perhaps, for clarification, something that might take the form "C: SetVolume -slevel 50" or something.

  Read the article

• Network config for KVM on physical machine with single NIC and single public IP

  - by neo0

  I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

  Read the article

• How to bypass resume from hibernate [closed]

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• running automated fsck on remote server

  - by GriffinHeart

  I had another question about df, and now i came to conclusion i need to run fsck my partition, i've been reading about it and would like some advice, if possible. The situation is like this, no physical access to the server and i want to run fsck. from what i read i just need to touch /forcefsck and when i reboot it will run fsck. My question is, at its basis, with what arguments will the fsck run? Will it need user input to correct errors, etc? and after running will it save a log of what happened? if this was how it ran it would be perfect, anyway of enforcing that on reboot? fsck -v -p /machine/disk/p1 2>&1 > fscklog.txt Also here they describe this: it's also a good idea on debian and debian-derivatives like ubuntu to edit /etc/default/rcS on remote servers and set "FSCKFIX=yes" that adds "-y" to the boot time fsck, so it doesn't risk the remote server being stuck waiting for someone to login at the console and run fsck. But on Centos that doesn't seem to exist I only have ssh access at the moment so that is why i'm being so picky with it. here's some info about disks and mounted volumes on the server: http://pastebin.centos.org/33314 Thanks.

  Read the article

• How to restore broken Ethernet functionality on Mac G5 running Mac OS 10.4.11 (Tiger)

  - by willc2

  I had a disk error that rendered my Mac unbootable. I repaired it with Tech Tool 4, but now networking does not work. Network Preferences reports that my Ethernet cable is unplugged. I know this is bogus because when I boot from an emergency partition, networking works correctly. Furthermore, wireless networking is also broken, which I tested with a known-good Wi-Fi dongle. Whenever I try to change Network Port Configurations by creating a New or Renaming an existing one, example: I get this message in the console: Error - PortScanner - setDevice, device == nil! Error - PortScanner - setDevice, device == nil! In sets of two as shown. When I try to invoke the Network Diagnostics app, it immediately crashes. My first thought is to reinstall Tiger with the Archive and Install method so I don't have to reinstall all my applications but I have lost my Tiger installer disk. My next thought is to buy Leopard for $107 on Amazon. If there is any way I can just repair my Tiger install I would be happy to save that money, though. This is not my main machine and I am loathe to put more money into it. How can I recover my network functionality? UPDATE: I found my Tiger install disk and tried an Archive and Install. It failed with an unhelpful error message along the lines of "Can't install, try again". I tried again but had the same error. My guess is, some corrupt or missing file in my User folder is preventing migration. I have a backup created with Super Duper that is a bit out of date but will startup the machine (with functional networking). I would love to just copy over the file(s) that got messed up but I don't even know where to look. What is the likely location of the System files that would cause the aforementioned symptoms?

  Read the article

• Security and data backup for Ubuntu usb installation

  - by AMS949

  Due to encryption on my corporate laptop I opted to install Ubuntu 9.10 on a flash drive and just use it as my hard drive. I tried the vmware but it crashed my xp a couple of times. Now I have a couple of concerns since I am totally new to Ubuntu and Linux. First, would it be possible for me to transfer my installation to a new usb drive? I now have a 4gb and it may get filled up soon, I don't seem to be able to see my actual files when I browse the usb drive. I also tried copying all files from this usb to another and boot from it but that failed. Second, whenever the system boots up I am never prompted for a password, it is always the username ubuntu. Which I guess means if I lose my usb drive my data is open wide. Is there a way to secure it or to use users and groups as on a regular hard drive installation? As a background, I created this by going into a working Ubuntu installation, System - Administration - USB Starter Disk Creator (was that the right way to start with?) Thanks!

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• Windows XP consuming drive letters

  - by billdehaan

  This one's a bit of a stumper. I'm running XP SP3, current with all fixes, etc. My problem is that I can assign a drive letter to a container file (explained below), it works just fine. But once I close the container, the drive letter is no longer available until the next boot. I've got some confidential data that I've placed in a container volume. I've used TrueCrypt (www.truecrypt.com) and FreeOTFE (www.freeotfe.org), with both installed and portable versions for both, with the same result. I open the container file, assign it to a drive letter (say R:), and run some portable apps that are within the volume. When I'm done, I close the container, and the drive letter is released. Fine so far. However, when I attempt to re-open it, the previous drive letter (in this case R:) is no longer available. It's not mapped to anything, it's just unavailable. Even attempting something like "subst R: C:\" returns "Invalid Parameter - R:". I can use the S: drive, no problem, but the next day I have to use T:, then U:, etc. Eventually, I have to reboot to reclaim all of of the drive letters. Unfortunately, everything I've read about drive letters relates to USB assignments, which doesn't apply here. I've tried the "show hidden" command (set devmgr_show_nonpresent_devices=1) with no success. And the Disk Management tool doesn't apply either, since it's not a physical drive. Does anyone know where Windows keeps the list of drive letters? And is there anything short of a reboot that can be used to reset it?

  Read the article

• Group Policy installation failed error 1274

  - by David Thomas Garcia

  I'm trying to deploy an MSI via the Group Policy in Active Directory. But these are the errors I'm getting in the System event log after logging in: The assignment of application XStandard from policy install failed. The error was : %%1274 The removal of the assignment of application XStandard from policy install failed. The error was : %%2 Failed to apply changes to software installation settings. The installation of software deployed through Group Policy for this user has been delayed until the next logon because the changes must be applied before the user logon. The error was : %%1274 The Group Policy Client Side Extension Software Installation was unable to apply one or more settings because the changes must be processed before system startup or user logon. The system will wait for Group Policy processing to finish completely before the next startup or logon for this user, and this may result in slow startup and boot performance. When I reboot and log in again I simply get the same messages about needing to perform the update before the next logon. I'm on a Windows Vista 32-bit laptop. I'm rather new to deploying via group policy so what other information would be helpful in determining the issue? I tried a different MSI with the same results. I'm able to install the MSI using the command line and msiexec when logged into the computer, so I know the MSI is working ok at least.

  Read the article

• Need clear steps on how to convert a Windows 2000 Server to a XenServer VM

  - by Jay

  The source system is not local. The target host running XenServer is not local. The source system is running Windows 2000 Server SP4 and has 1 disk split into 6 partitions, all NTFS: C: 6 GB (boot) D: 15 GB E: 6 GB F: 6 GB G: 5 GB H: 26 GB Most of the partitions are mostly mostly full ( 60%). What is the most straightforward way to do a P2V migration of the server? I can do minor database & data syncs after the P2V is successful & running as a VM within XenServer, it's just getting to that point which is not clear. The option of installing a Windows 2000 Server from scratch is not available, I need to convert the existing physical server as-is into a VM to be hosted within a XenServer environment. I've looked at XenConvert but it maxes out on converting only 4 partitions in one shot, and I'm not certain how to account for the 2 extra partitions. I'm not familiar with XenServer but it's my only option right now to go P2V.

  Read the article

• [Ubuntu 10.04] mdadm - Can't get RAID5 Array To Start

  - by Matthew Hodgkins

  Hello, after a power failure my RAID array refuses to start. When I boot I have to sudo mdadm --assemble --force /dev/md0 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 to get mdadm to notice the array. Here are the details (after I force assemble). sudo mdadm --misc --detail /dev/md0: /dev/md0: Version : 00.90 Creation Time : Sun Apr 25 01:39:25 2010 Raid Level : raid5 Used Dev Size : 1465135872 (1397.26 GiB 1500.30 GB) Raid Devices : 6 Total Devices : 6 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 17 23:02:38 2010 State : active, Not Started Active Devices : 6 Working Devices : 6 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 128K UUID : 44a8f730:b9bea6ea:3a28392c:12b22235 (local to host hodge-fs) Events : 0.1249691 Number Major Minor RaidDevice State 0 8 65 0 active sync /dev/sde1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 49 3 active sync /dev/sdd1 4 8 33 4 active sync /dev/sdc1 5 8 17 5 active sync /dev/sdb1 mdadm.conf: # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions /dev/sdb1 /dev/sdb1 # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # definitions of existing MD arrays ARRAY /dev/md0 level=raid5 num-devices=6 UUID=44a8f730:b9bea6ea:3a28392c:12b22235 Any help would be appreciated.

  Read the article

• How to enable synergy 24800 (or some other port) through firewalld

  - by ndasusers

  After upgrading to Fedora 18, Synergy, the keyboard sharing system was blocked by default. The culprit was firewalld, which happily ignored my previous settings made in the Fedora GUI, backed by iptables. ~]$ ps aux | grep firewall root 3222 0.0 1.2 22364 12336 ? Ss 18:17 0:00 /usr/bin/python /usr/sbin/firewalld --nofork david 3783 0.0 0.0 4788 808 pts/0 S+ 20:08 0:00 grep --color=auto firewall ~]$ Ok, so how to get around this? I did sudo killall firealld for several weeks, but that got annoying every time I rebooted. It was time to look for some clues. There were several one liners, but they did not work for me. They kept spitting out the help text. For example: ~]$ sudo firewall-cmd --zone=internal --add --port=24800/tcp [sudo] password for auser: option --add not a unique prefix Also, posts that clamied this command worked also stated it was temporary, unable to survive a reboot. I ended up adding a file to the config directory to be loaded in on boot. Would anyone be able to have a look at that and see if I missed something? Though synergy works, when I run the list command, I get no result: ~]$ sudo firewall-cmd --zone=internal --list-services ipp-client mdns dhcpv6-client ssh samba-client ~]$ sudo firewall-cmd --zone=internal --list-ports ~]$

  Read the article

• How to transfer Windows Vista disk image to new machine

  - by Mike Hobbs

  I'm trying to upgrade a user's machine to some better hardware. I know of Easy Transfer, but I'd rather not have to reinstall all the programs that are already present. (Some of which are no longer available, anyway). Instead, I'm trying to transfer the entire disk image from one machine to the other, but I ran into issues. If I copy the partition image over to the new machine using Clonezilla, I get errors on boot saying that I need to insert the Vista install disk and run repair. I do that, but it then says that it is unable to repair whatever it is that's broken. Next, I tried to sysprep the old machine before creating the image, but sysprep fails saying that it encountered some sort of system error. Should it be possible to sysprep any arbitrary machine, or does it only work on a relatively clean install? Could it be a missing driver that is tripping me up? The new machine is a fairly stock desktop that shouldn't need any special drivers beyond what's already present in standard Vista. Are there any foolproof methods for doing this sort of thing?

  Read the article

• locked files on HFS+ home partition shared between OSX/Linux

  - by HazyBlueDot

  I dual boot into Arch Linux and OS X 10.6 on my MacBook pro. I synced my UID between both OSes and created an HFS partition (with no journaling) to use as a shared home/Users partition. For the most part it works just as I'd expect, but sometimes when I'm booted into OS X certain files are "locked" (when I get info on a particular file the "Locked" box is checked under the "General" pane. I can resolve the issue by manually unchecking the box) and/or I get "Operation not permitted" when I try deleting or chmod'ing a file. In both cases I don't see anything out of the ordinary on the permission bits displayed with ls -l, except for a trailing '@' character in the position where the sticky bit would normally occur: -rw-r--r--@ 1 myuser mygroup 296 Mar 29 11:44 myfile This '@' character shows up on ALL normal files, so doesn't seem to be linked to the locked/operation not permission situation. On the Linux side of things I never have permission problems. To the best of my limited knowledge and experience with ACLs I've not found any ACLs on any of the files in question. For what it's worth, I do most of my file editing using emacs (Aquamacs in OSX), is it possible it is setting weird permission bits? What is the "locked" setting that OS X uses and does it have a permission bit equivalent (so at the very least I could recursively unlock all files in my home directory from the terminal) why might some, but not other files get "locked" when booting into OS X what is the meaning of the '@' character?

  Read the article

< Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >