Search Results

Search found 11897 results on 476 pages for 'dean rather'.

Page 319/476 | < Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >

• Bypassing Router's DNS Settings

  - by Ramon Marco Navarro

  Is there a way to bypass my ISP provided CPE/router's DNS settings? I'd like to use OpenDNS but I am unable to access the administrator acount of the CPE. I tried logging in using the default passwords (admin/admin, admin/1234, etc) to no avail. I found out later that the admin password is generated using a generator where you input the CPE's MAC address. I tried emailing the manufacturer of the CPE (Huawei, the CPE is Huawei BM625) and my ISP but they aren't replying. I also saw similar queries (lots of them!) at Huawei's forums, without a single reply. So as a last resort, I'd like to know a way to bypass the CPE's DNS settings. My subscription is for a WiMAX service. I'm using Windows 7 and have already set the DNS settings for the Local Area Connection. But I still am not seeing the "You are already using OpenDNS" text at OpenDNS's site. And when explicitly using the OpenDNS servers I still seem to get 208.69.38.150 rather than the expected 208.69.38.160: nslookup www.opendns.com. 208.67.222.222 Server: resolver1.opendns.com Address: 208.67.222.222 Non-authoritative answer: Name: www.opendns.com Address: 208.69.38.150

  Read the article

• Disable raid member check upon mount to mount damaged nvidia raid1 member

  - by Halfgaar

  Hi, A friend of mine destroyed his Nvidia RAID1 array somehow and in trying to fix it, he ended up with a non-working array. Because of the RAID metadata, the actual disk data was stored at an offset from the beginning. I was able to identify this offset with dd and a hexeditor and then I used losetup to create a loop device with the proper offset, so that I could mount the partition. It was then that I ran into problems, namely that mount says: "mount: unknown filesystem type 'nvidia_raid_member'". I also had this when trying to mount a Linux MD component the other day, and because I can remember that doing that in the past worked, I surmised that it may be some kind of protection. I therefore booted an old Sysrescue CD and tried it there, which worked (because of the older version of mount/libc/kernel/whatever). I still need to try to get more data, and because I don't want to keep using that SysrecueCD, I'd like to be able to mount the disk on my normal system. So, my question is: can the check for a disk being a raid member be disabled? I guess I could also zero out blocks that look like the raid block, but I'd rather not... I made an image of the disk with par2 data, so it's revertable, but still...

  Read the article

• What is there in Win 7 Pro (or Ultimate) that is not there in Home Premium? - Especially considering this situation..

  - by Senthil

  I want to know the REAL difference between Windows 7 Home Premium and Professional/Utimate. In India, the cost of different versions: Ultimate - 11,200 INR Professional - 10,700 INR Home Premium - 6,600 INR The absolute cost of the first two is so high to me that the difference (500 INR) doesn't matter. So to me there is really no choice between the first two - If I decide to buy the Professional version, I'd rather go for Ultimate itself. What I want to know is, whether Home Premium is enough for my needs. I tried searching for comparison but many look like just marketing junk from MS. They are short and vague. According to this page, the major differences between Pro and HomePremium are Run many Windows XP productivity programs in Windows XP Mode. Connect to company networks easily and more securely with Domain Join. You can do both in Pro but not in Home Premium. I intend to use my Windows 7 for a small business - just starting up. So I'll be dealing with the following: All kinds of development tools, servers Very important - I will run Virtual Machine Software (MS VPC or VMWare or Sun VirtualBox etc..) My system will be acting as the server for most purposes till I can afford dedicated servers. Connect the system to a variety of network devices (PCs, Printers, etc..) Run productivity, business and financial apps Any other small software startup business requirement that I haven't thought of yet. Professional (and Ultimate) is twice as expensive as Home Premium. So it'd be great if someone can point out the things you cannot do with Home Premium, when you use it like I explained above, so that I can make a decision about which one to buy. I need some real-life experiences so that I can make an informed decision - not a decision based on marketing junk.

  Read the article

• Looking for USB Network Attached Storage (NAS) Adapter that supports multiple drives, NTFS/FAT32 fil

  - by braveterry

  I'm looking for a NAS Adapter that supports attaching multiple USB devices to the network. Here's what I'd like to see in a NAS adapter: Under $100.00. Support for multiple devices. This can be through a USB hub or through multiple USB connectors on the device itself. Bittorrent support would be nice, but this isn't a deal-breaker. Filesystem support for at least NTFS or FAT32. I'd prefer to not have to reformat to use the device, but this is also not a deal-breaker. Here is what I am NOT looking for: I'm NOT looking for a NAS enclosure. I already have a couple of spare external USB drives that I'd like to use. I'm NOT looking for a networked USB hub like the one mentioned here. Network USB hubs only allow access to a drive from one PC at a time. I'm NOT looking for a wireless router with a NAS built in. I already have a wireless router, and I'd rather not go through the hassle of replacing it if possible. What I've looked at so far PogoPlug: This supports multiple devices via a USB hub, but there's not Bittorrent support. It's $99.00, so I may end up going with this and hope that they patch in Bittorrent support later. Addonics NAS Adapter: This supports only one device per adapter, so it's a non-starter. SimpleNET NAS Head USB 2.0 Portable Dongle: I'm not 100% sure this supports multiple devices. Plus there doesn't seem to be any Bittorrent support. I'll try to update this post as I explore other devices.

  Read the article

• "Could not claim interface on camera: -6" when trying to connect usb camera (Kinect)

  - by rzetterberg

  I have installed the freenect library from openkinect.org. With that library there is a demo application which you can run from the terminal to test out the Kinect. However when I run this command I get the following output: richard@behemoth:~$ sudo freenect-glview Kinect camera test Number of devices found: 1 Could not claim interface on camera: -6 Could not open device This particular error is thrown by the library libusb by the function libusb_claim_interface and the error -6 corresponds to the LIBUSB_ERROR_BUSY. So my guess is that it has something to do with mounting the usb, rather than specifically the freenect library or the Kinect itself. So my question is how can I find out what resource is using this interface and how can I free it so that I can access it? Edit: What I have tried so far (just to be sure): Rebooted Plugged-out, plugged-in Tried different usb ports Restarted udev Additional information that might be useful: /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=1c73f217-ac8d-451b-8390-7a680628a856 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=bb49bd29-07ec-45a0-bbab-46fb8362b06b none swap sw 0 0 sudo uname -r: Linux behemoth 3.0.0-14-generic-pae #23-Ubuntu SMP Mon Nov 21 22:07:10 UTC 2011 i686 i686 i386 GNU/Linux cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10"

  Read the article

• RoboCopy fails with "the specified network name is no longer available"

  - by Justin Scott

  We have a scheduled task that runs robocopy periodically to mirror a rather large folder structure from one server to another (thousands of folders, 100,000+ files, 50+ GB in size). There is a share on the receiving server where the mirror gets stored. We're running the task from the origin server connecting out to the share on the receiving end. Both servers run Windows Server 2003 and are connected to the same network switch (100Mbps). The process will sometimes complete all the way through without error. More often than not, however, at some point during the process (seems random as to where), robocopy will fail with the error The specified network name is no longer available. It will wait 30 seconds and try the file again and eventually give up after a number of retries. Process will repeat at the next schedule interval and may complete... or not. When this occurs I am not able to access the share at all on the destination server from anywhere on the network for up to 30 minutes. There is nothing else on the network using this share. My question is what does this error mean specifically? Why is the share "dropping off" and becoming inaccessible? Is there a way to prevent it and get the file mirroring to be more stable?

  Read the article

• Server 2008 R2 Dns Lockup

  - by Richard Maynard

  Hi, We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed Thanks in advance. Regards,

  Read the article

• How can I forward an application with X11 in grayscale

  - by ??????? ???????????

  I am trying to run a graphical application at home and display it on a it on a laptop which is located about six routing hops away. The problem is that the connection is so slow (or rather there is so much GOOEY being transfered) that the mouse is unresponsive and it takes a "long time" to redraw the window even at a resolution of 800x600 pixels. The connection speeds are 10MBit up at home and about 1MBit down on the laptop, which I think should be sufficient for looking at some GUI in (almost) real time. Since this traffic is sent over over a secure shell, I have enabled Compression with highest CompressionLevel along with Ciphers set to blowfish-cbc. This has substantially improved the responsiveness of the application, making it nearly usable. However, my goal is to improve the performance even further by sacrificing colors and even frame rate. The application to be displayed a Qemu SDL window with a graphically-oriented OS in it. This is not strictly relevant, but perhaps there are options to tweak the SDL output which I am not aware of. A possible workaround would be to run the application in a "hidden" X server and enabling TigerVNC on that X server. This would automatically give me the benefits of an optimized VNC viewport, but the goal is to do without (reduce complexity). The question I'm asking is what are my options for reducing the data-rate generated on the server in order to make the graphical application more usable on the client. As mentioned, colors are not important and I could probably work with 5-16 fps. Both machines are running Gentoo with the software in question being: workstation X.Org X Server 1.10.4 OpenSSH_5.8p1-hpn13v10, OpenSSL 1.0.0e QEMU emulator version 0.15.1 (qemu-kvm-0.15.1) laptop X.Org X Server 1.12.2 OpenSSH_5.8p1-hpn13v10lpk, OpenSSL 1.0.0j

  Read the article

• To install Markdown's extensions by Python

  - by Masi

  The installation notes (git://gitorious.org/python-markdown/mainline.git) say in the file using_as_module.txt One of the parameters that you can pass is a list of Extensions. Extensions must be available as python modules either within the markdown.extensions package or on your PYTHONPATH with names starting with mdx_, followed by the name of the extension. Thus, extensions=['footnotes'] will first look for the module markdown.extensions.footnotes, then a module named mdx_footnotes. See the documentation specific to the extension you are using for help in specifying configuration settings for that extension. I put the folder "extensions" to ~/bin/python/ such that my PYTHONPATH is the following export PYTHONPATH=/Users/masi/bin/python/:/opt/local/Library/Frameworks/Python.framework/Versions/2.6/ The instructions say that I need to import the addons such that import markdown import <module-name> However, I cannot see any module in my Python. This suggests me that the extensions are not available as "python modules - - on [my] PYTHONPATH with names starting with mdx_ - -." How can you get Markdown's extensions to work? 2nd attempt I run at ~/bin/markdown git clone git://gitorious.org/python-markdown/mainline.git python-markdown cd python-markdown python setup.py install I put the folder /Users/masi/bin/markdown/python-markdown/build to my PATH because the installation message suggests me that is the new location of the extensions. I have the following in a test markdown -document [TOC] -- headings here with # -format --- However, I do not get the table of contents. This suggests me that we need to somehow activate the extensions when we compile by the markdown.py -script. **The problem returns to my first quoted text which I is rather confusing to me.

  Read the article

• Web based KVM management for Ubuntu

  - by Tim

  Hey all, We've got a single Ubuntu 9.10 root server on which we want to run multiple KVM virtual machines. To administer these virtual machines I'd like a web based KVM management tool, but I don't know which one to choose from the list of tools mentioned on linux-kvm.org. I've used virsh & virt-manager on my desktop, but would like a web interface for the server. I tested ConVirt on my desktop, but it failed to pickup KVM machines from virsh / virt-manager, and I could not get KVM virtual machine import to work (only Xen). oVirt looks good, but I can't find out if and how I can install it on Ubuntu 9.10.. (And I'd really rather not waste another few days on testing stuff that might not work in the end.) Can anyone recommend any good web based KVM management tools that are easy to install on Ubuntu 9.10? I'm looking for something that will also allow me to run other services like apache and postgresql besides hosting virtual machines, so preferably fairly lightweight & no dedicated OS installs. We don't need any professional clustering / migration or anything, just something that will let us create, start, inspect, administer & stop virtual machines from a web page. Best regards, Tim

  Read the article

• Can a CNAME be a hostname

  - by pulegium

  This is bit of a theological question, but nonetheless... So, a server has a hostname, let's say the fqdn is hostname.example.com (to be really precise about what I mean, this is the name that is set in /etc/sysconfig/network). The very same server has multiple interfaces on different subnets. Let's say the IPs are 10.0.0.1 and 10.0.1.1. Now the question is, is it theoretically (mind you, this is important, I know that practically it works, but I'm interested in purely academic answer) allowed to have the following setup: interface1.example.com. IN A 10.0.0.1 interface2.example.com. IN A 10.0.1.1 hostname.example.com. IN CNAME interface1.example.com. OR should it rather be: hostname.example.com. IN A 10.0.0.1 interface2.example.com. IN A 10.0.1.1 interface1.example.com. IN CNAME hostname.example.com. I guess it's obvious which one is making more sense from the management/administration POV, but is it technically correct? The argument against the first setup is that a reverse lookup to 10.0.0.1 returns interface1.example.com and not what one might expect (ie the hostname: hostname.example.com), so the forward request and then sub sequential reverse lookups would return different results. Now, as I said, I want a theoretical answer. Links to RFC sections etc, that explicitly allows or disallows use of CNAME name as a hostname. If there's none, that's fine too, I just need to confirm. I failed to find any explicit statements so far, bar this book, where this situation is given as an example and implies that it can be done as one of the ways to avoid MX records pointing to a CNAME.

  Read the article

• nginx subdomains improperly act like wildcard?

  - by binjured

  I have an odd problem with nginx subdomains. First, my configuration: server { listen 443 ssl; server_name secure.example.com; ssl_certificate example.crt; ssl_certificate_key example.key; keepalive_timeout 70; location / { fastcgi_pass 127.0.0.1:8000; ... } } server { listen 80; server_name example.com www.example.com; location / { fastcgi_pass 127.0.0.1:8000; ... } } The idea being that I have a secure domain, secure.example.com and a normal domain, example.com. In practice, I can go to https://example.com and http://secure.example.com. I worked around the second issue with an intermediary server: server { listen 80; server_name secure.example.com; rewrite ^(.*) https://secure.example.com$1 permanent; } But this is not an optimal solution and I'd have to create another one to redirect https on the tld to the subdomain. I feel like I must be doing something wrong if I need multiple servers like that. Why does https://example.com work when there is no server listening on 443 there? Shouldn't it just fail to connect? I'm rather confused.

  Read the article

• Ubuntu/Nvidia lists DVI dual cable as single

  - by Joseph Mastey

  I have an NVidia Quadro FX 880M graphics card, from which I am trying to drive 2 monitors: my internal laptop montior (15.6", 1920x1080, Nvidia driver says it's running via DisplayPort) and an external 27" monitor (Dell U2711, 2560x1440 native resolution, via DVI). I've hooked the dual DVI cable to the dual DVI port on my dock (Dell PR03X) and installed the proprietary NVidia driver, but I cannot seem to get the full 2560x1440 out of the larger 27" external monitor. Looking at the NVidia driver settings, the monitor's connection is reported as a single DVI cable, rather than a dual one, which would explain the reduced resolution. Does anyone have any experience with an issue like this? What can I do to make full use of my new monitor? (Possibly) Relevant Information: There is no DVI port on the laptop itself, but one is provided via the dock. The laptop and dock both provide a DisplayPort jack, but I have been unable to get this working on either w/ the monitor. I did have the nouveau driver installed when I installed the nvidia proprietary driver, but have since removed it (no change in the monitor situation when I removed it). The 27" reports a max resolution of 1680x1050. Thanks, Joe

  Read the article

• Route specific HTTP requests through pfSense OpenVPN

  - by DennisQ

  Hi, to start, I have very little knowledge on routes, iptables, etc. That said, here's what I'm trying to accomplish and where I think I'm stumped: Problem: We have an external website which we recently firewalled so it only accepts traffic from our office IP addresses. This works well at the office, but doesn't work for remote access through VPN as we don't route all traffic through OpenVPN. I would rather avoid forcing everyone to route all traffic through just to accommodate this one site. Environment: Main router box is running pfSense. Em0 is internal IP, Em1 is external. Internal net is 10.23.x and VPN is 10.0.8.0/24 I believe what I need to do is add a route to the VPN server config to send all traffic to that IP over the VPN tunnel. I think that part's working, but I don't get a response back, so I'm assuming that I need some NAT config on the VPN server to route the response back over the tunnel? What I've found so far is to try the following, but since this is a pfSense box on FreeBSD, I can't run iptables, etc. Make sure ip forwarding is enabled: echo 1 /proc/sys/net/ipv4/ip_forward Setup NAT back out: iptables -t nat -A POSTROUTING -s 10.0.8.0/24 -o em0 -j MASQUERADE Am I on the right path, and if so how do I accomplish this through pfSense UI or FreeBSD CLI? Thanks!

  Read the article

• Unconvert Text File from Binary Format

  - by Hammer Bro.

  I've got a rather large CSV file (~700MB) which I know to consist of lines of 27-character alpha-numeric hashes; no commas or anything fancy. Somehow, during its migration from Windows to Linux (via winSCP and then a few regular SCPs), it has converted into some kind of binary format I am unfamiliar with. If I open the file in vi, everything appears fine, and it says [converted] at the bottom, although I know it's not a line endings issue (and dos2unix doesn't help). If I 'head' the file, it looks proper except for a "ÿþ" at the beginning of the first line. If I open up the file in nano, however, I see the "ÿþ" at the start and then "^@" before every character (even newlines and EoF). If I try to re-save or copy the file (say via: head file.csv short.txt), this special encoding is preserved. I copied the first ten lines out of vi (which displays it properly) into my Windows clipboard via my SSH client, then pasted it into a new text file, test.txt. This file is visually identical when opened in vi (and similar through 'head', minus the "ÿþ"), although it's roughly half of the filesize. Additionally, file test.txt test.txt: ASCII text file short.txt short.txt: I have no idea what format this once-text file got converted to (it's notoriously hard to search the internet for symbols), but surely there must be some way to convert it back. Any ideas?

  Read the article

• How to make sysctl network bridge settings persist after a reboot?

  - by user183394

  I am setting up a notebook for software demo purpose. The machine has 8GB RAM, a Core i7 Intel CPU, a 128GB SSD, and runs Ubuntu 12.04 LTS 64bit. The notebook is used as a KVM host and runs a few KVM guests. All such guests use the virbr0 default bridge. To enable them to communicate with each other using multicast, I added the following to the host's /etc/sysctl.conf, as shown below net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 Afterwards, following man sysctl(8), I issued the following: sudo /sbin/sysctl -p /etc/sysctl.conf My understanding is that this should make these settings persist over reboots. I tested it, and was surprised to find out the following: root@sdn1 :/proc/sys/net/bridge# more *tables :::::::::::::: bridge-nf-call-arptables :::::::::::::: 1 :::::::::::::: bridge-nf-call-ip6tables :::::::::::::: 1 :::::::::::::: bridge-nf-call-iptables :::::::::::::: 1 All defaults are coming back! Yes. I can use some kludgy "get arounds" such as putting a /sbin/sysctl -p /etc/sysctl.conf into the host's /etc/rc.local but I would rather "do it right". Did I misunderstand the man page or is there something that I missed? Thanks for any hints. -- Zack

  Read the article

• Outgrew MongoDB … now what?

  - by samsmith

  We dump debug and transaction logs into mongodb. We really like mongodb because: Blazing insert perf document oriented Ability to let the engine drop inserts when needed for performance But there is this big problem with mongodb: The index must fit in physical RAM. In practice, this limits us to 80-150gb of raw data (we currently run on a system with 16gb RAM). Sooooo, for us to have 500gb or a tb of data, we would need 50gb or 80gb of RAM. Yes, I know this is possible. We can add servers and use mongo sharding. We can buy a special server box that can take 100 or 200 gb of RAM, but this is the tail wagging the dog! We could spend boucoup $$$ on hardware to run FOSS, when SQL Server Express can handle WAY more data on WAY less hardware than Mongo (SQL Server does not meet our architectural desires, or we would use it!) We are not going to spend huge $ on hardware here, because it is necessary only because of the Mongo architecture, not because of the inherent processing/storage needs. (And sharding? Please! Cost aside, who needs the ongoing complexity of three, five, or more servers to manage a relatively small load?) Bottom line: MongoDB is FOSS, but we gotta spend $$$$$$$ on hardware to run it? We sould rather buy commercial SW! I am sure we are not the first to hit this issue, so we ask the community: Where do we go next? (We already run Mongo v2) Thanks!!

  Read the article

• DrayTek 2820 configuration using public IP addresses

  - by Kev

  I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

  Read the article

• SAN Replication for Fault tolerance using EVA4400

  - by Sergei

  Hi Everyone, I hope that someone would point me in the correct direction - it looks like I have no enough konwledge in the subject and timeframes are too tight for me to explore different scenarios in depth.. We have two datacenters few miles away from each other connected by 100 Mbps link.Each datacenter will have 5 BL490 blades with ESX Standard hosting about 50 VMs. Eac hsite has HP eva4400 SAN with SAN replication set up.VC is going to be in the first datacenter and both datacenter are networked. SAN Replication is block level so it seems like I cannot just replicate changes but all writes would have to be replicated.This should not be a problem as link can sustain about 1.8 TB a dayand data can be buffered. I am having trouble however visioning how recovery would work in this case.We don't need instant recovery , I would say 4 hours recovery time is accepted so fancy automatic SRM like DR scenario would not be easily accepted due to the financial reasons, however any comments are welcomed. Current idea is following: replicate LUNs from primary site to the secondary.When disaster strikes, IT personnel switches on ESX hosts on the remote side and connects replicated LUNS to them, then registers VMs and changes IP address. I understand that this seems like horribly manual process and I almost sure I have missed some obvious pitfalls here. Could someone let me know what direction should I go?An articles regarding the subject? This is a brand new setup and we would rather build up basic recovery process and scale it later.I just need to have a right direction to allow for such scalability. Thank you very much in advance!

  Read the article

• Giving Select Windows Domain Users Symbolic Link Privilege

  - by fp0n

  I would like to setup select users on our domain to have the ability to create symbolic links on local NTFS drives and network shares without needing to run as Administrator, as part of an application with will call the CreateSymbolicLink() API directly. The default configuration for our users is to be Administrator of their computer and I think I am fighting UAC to make the privileges work the way that I want because of that. I found this link on MSDN: http://social.msdn.microsoft.com/Forums/en-SG/windowssdk/thread/fa504848-a5ea-4e84-99b7-0eb4e469cbef which describes the interaction between the SeCreateSymbolicLinkPrivilege, UAC and a domain but really does not have a solution. Here's the three options I've come up with: 1) Create a new group, give the SeCreateSymbolicLinkPrivilege to the group and assign users to the group 2) Give each individual user (2 now, more later) the privilege 3) Give the privilege to the default User group which opens it up to all Users 4) Change config so Users are not Admins by default (probably would work but not likely) Based on my testing, only 3 works for me and that is the least desirable but I've only got a local server to test with, not a domain. I need to recommend to the admin how to set this up and also have something that we can easily explain to other users of our application that are on their own domain or not on a domain. The other option seems to be to create a Service that runs with a SYSTEM account that creates the links for the application but I'd rather not go that route. Thanks.

  Read the article

• Can I change the "From" name and address without going into Mail.app's preferences?

  - by Arjan van Bentem

  Can I somehow add an editable "From" field to Mail.app, a bit like Virtual Identity for Thunderbird, just like I could change the "Reply To" address on the fly? In Mail.app, one can set up multiple email addresses for a single account by just entering a comma-seperated list like [email protected], [email protected]. Next, when composing a message, Mail offers a dropdown to select a "From" address. And when replying†, it automatically selects the right address if it can find a match: Nice, but I'd like to be able to change the "From" on the fly, without going into the Account Information. Also, in previous versions of Mail one could even specify multiple Full Names for a single account: Email Address: Arjan <[email protected]>, Arjan on SU <[email protected]> But nowadays, Mail only uses the setting of Full Name, and even ignores names in the Email Address field when no value for Full Name is set at all. Hence, it would be great if I could change the Full Name on the fly as well. I had no luck finding a plugin for Mail yet. † When using sub-addressing, anything that is sent to [email protected] is simply delivered to [email protected]. I'd then like to reply with the same full address, rather than just [email protected] if Mail cannot find a match, without going into the Account Information first. I sometimes also want to compose a new message with a new sub-addressing-address.

  Read the article

• Browsing Audiobooks on an iPod Nano

  - by Electrons_Ahoy

  The sitation: I've got a stack of audiobooks in MP3 format in my iTunes library, and both an iPhone and an iPod Nano. After this question, I've changed the Media Kind for the audiobook MP3s from Music to Audiobook. This has been, overall, spectacular, as now I can resume where I was, they show up under Audiobooks, etc. On the iPhone, it's also super convenient, since the interface shows what used to be an album with multiple songs as a single book with multiple chapters, and going into "Audiobooks" presents me with a list of books, not tracks. The Nano, on the other hand, is a little strange. After changing the media type and re-syncing the ipod, the files in question are now listed under Audiobooks rather than Music, and the extra Audiobook features are present (resume playback and so on,) but the Audiobooks menu just lists all the MP3 tracks on the iPod in alphabetical order, ignoring whichever book/album they belong to - and doesn't seem to let me browse them any other way. This is, clearly, a little sub-optimal. Did I screw something up? How do I get the Nano to treat the files in a similar way to the way the iPhone and iTunes does - as books with chapters? Is there a step I missed somewhere? Do I need to reformat the iPod? Is this even possible? (Footnote: shameless bump, since this just scored me a tumbleweed.)

  Read the article

• MacBook Pro battery capacity 65K mAh

  - by Alexander Gladysh

  I have a 15" MacBook Pro 3.1 (that is Late 2007 model AFAIR). I've bought it new a couple of years ago. Recently its on-battery power lifespan became very short (30 to 10 minutes). When my notebook turns itself off due to "low battery" and I press the small button on the battery itself, all LED lights are alight, indicating full charge. When I plug in the power adapter, my Mac displays that "battery is fully charged, finishing charging process" (I have a Russian OS X 10.5.7, so that is a rough translation), but the LEDs on battery itself display (seemingly accurate) status that there are one or two "LEDs still not charged". My battery have as few as 37 recharge cycles (yes, I've neglected calibration over the time I've used it). Battery info programs like iBatt2 report battery capacity of 65 337 mAh (with by-design capacity of 5600 mAh). I get it that something went wrong with battery electronics. I've tried resetting my Mac's PRAM and SMC, it did not changed anything. Now I'm trying to recalibrate the battery, but looks like it does not help as well. Will try to recalibrate it several times in a row. I'd buy a new battery if I knew if it is battery fault, not a notebook's. Any suggestions? Update: After recalibration, my battery status now displays battery capacity of 1500 mAh. But with every recalibration (or simply when I use notebook without power adapter plugged in) this number changes in the range from 200 mAh to 1700 mAh. LEDs on battery now are synchronous with what nodebook thinks on the charge level. Also I've noticed that cycle count changes rather slowly. It is now 39, it was 37 when I've started recalibration, and I went through the process at least ten times... So, the main question is: does it look like that replacing the battery would help me (or does it look like this is notebook's problem)? I guess I should try replacing the battery.

  Read the article

• Windows Authentication behaves oddly when VPN'd

  - by Dan F

  Hi all We've got a few apps that rely on windows authentication - a couple of web apps with AD auth turned on and we usually connect to our SQL servers with windows auth. This normally runs without a hitch. It doesn't work so well if we're VPN'd to a client site though. SSMS Opening SSMS normally from the start menu, then picking a server that normally accepts windows auth, results in a message saying: Login failed. The login is from an untrusted domain and cannot be used with Windows authentication. (.Net SqlClient Data Provider) If I drop to a command prompt and use runas /user:domain\user to launch SSMS I can successfully windows auth to our SQL server instances with that ssms process. If I look in task manager, both copies of ssms.exe (start menu vs runas) have the same user, and I can see no discernible differences between the processes in procexp. AD Auth websites If I open IE and browse to any of our websites that require an authenticated windows user, I get the "who are you" prompt, and that dialog thinks I'm whoever the VPN user is. I can click "Use another account" and authenticate that way though. Outlook Even Outlook prompts for a username when we are VPN'd! It's affecting our Win7 and Vista machines. It's been a while since we had an XP box, but I don't recall having this issue on XP for what it's worth. The VPN connections are just using the built in windows VPN connections, they're not fancy cisco VPNs or anything of that nature. Does anyone know how to tell windows that I'd like to be my normal old primary domain user rather than the VPN user when authenticating to resources in our domain? Heck, I'd be happy with a solution that prompted me with the "who are you" if I was trying to access windows auth requiring resources on the client's VPN. Thanks! Apologies if this is more a superuser question, I wasn't sure which site it best suited. It's about networking and infrastructure and plagues all of our developers here, so I hope it's a serverfault Q.

  Read the article

• VMWare Converter - Remote Linux Install P2V

  - by Zed Said

  I am trying to get what I thought was an easy process working. Here is my situation. I have a remote linux server (running Debian) that I would like to turn into a VM so that I can do testing on it rather than the production server. I downloaded VMWare Converter. I went to the "convert machine" wizard, chose Powered-on machine, entered my remote machine details. Clicking next shows that it correctly connects to my remote linux box. Now, on the next screen, for Destination type, it enters "WMWare Infrastructure virtual machine", and I can't change this. This is where I am stuck. Why do I need another sever to convert with? Is this where my VM gets sent to? And why can't I just convert the VM and save it on the computer that I am running the converter program on? If I do have to use a vmware infrastructure destination, I am confused at what ESX is, why and how I use it. Any help with this process would be more than appreciated!

  Read the article

< Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >