Search Results

Search found 18580 results on 744 pages for 'wireless connection'.

Page 32/744 | < Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >

  • Can't find PC on network

    - by Simon Verbeke
    I just got myself a new laptop, and set it up. It is connected to the wireless internet in my home. I then wanted to create a homegroup between the laptop and my desktop, but they can't find each other. Probably because the desktop has a wired connection to the router and the laptop is connected to a wireless access point. The router and the AP are connected to a switch in the middle by cable. A sketch of the network: Laptop - - - Wireless Access Point ----- Switch ----- Router ----- Desktop ^ ^ ^ ^ Wireless Wired Wired Wired They both point to the same gateway and DHCP-server (on 192.168.0.1). And I can ping to that address from both PCs. When I try to ping either of the PCs the pings time out. The subnets are also the same (255.255.255.0) and the IPs are in the same range (192.168.0.114 laptop, 192.168.0.205 desktop). So I don't really understand what I need to do to be able to access either computer from the other. The weird thing is that Synergy (to use mouse and keyboard over the network) works, just by using the IPs assigned to both PCs. The acces point is a linksys WAP54g, but I'm unsure of the Router, it has a custom casing from our ISP and hides any clues for identifying the product. I'm going to google a bit so I can add that info later. Both PC's are Windows 7 64 bit. The desktop is Ultimate, the laptop Professional.

    Read the article

  • Connection speed drops from 1 Gbps to 10 Mbps (Vista 64)

    - by Kevin Hakanson
    I recently got a Windows Home Server (HP MediaSmart Server EX490) setup so I could do backups and other things. However, I am having trouble on my Vista 64 PC. The backup will be making great progress, then it will just slow down. At one point, I noticed the lights on my Netgear GS105 indicated it was not using a 1000 Mbps connection, but a 10 Mbps one. I checked the Status of Local Area Connection (Intel(R) 82567V-2 Gigabit Network Connection) and that also showed the same slow speed. This has happened several times in the last couple days. When I disabled the network device, and then enabled it, it established the 1 Gpbs connection again. However, some of the times the Sent Bytes Activity on the Status windows indicate that the data flow is still slow (100 to 1000 bytes every couple seconds). Obviously, at this rate I could backup faster to floppy disk. :) My question is how to diagnose and fix this problem. When I look at the Administrative Events, I do a Errors: Bonjour Service 456: ERROR: read_msg errno 10054 (An existing connection was forcibly closed by the remote host.) And a Warning: e1yexpress Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected. I am suspicious there is some power saving mode. I found a post suggesting System Idle Power Saver(SIPS) may be the issue. I am going to try that, but looking for other suggestions or diagnostic advice. I have several new items in this configuration: server, client software, switch and cat6 cables.

    Read the article

  • Networking problems in VMWare with wireless bridge

    - by Robert Koritnik
    Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: wireless Guest network adapter 1: over Bridge VMNet (automatic) Guest network adapter 2: over Host only VMNet Problem When I surf the net within VM my internet connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitelly but connection won't pickup automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

    Read the article

  • Windows 7 Cable Connection Rehabilitation

    - by Giovanni De Gaetano
    I recently switched the operating system of my laptop from Windows XP to Windows 7. My web-connection is such that I need to identify everytime before connecting. Since there is no automatic identification request, while using Windows XP I was used to de-abilitate and rehabilitate the cable connection after every switching on. I successfully installed the web-connection on Windows 7, and later on I switched the computer off and on (simply because I had to sleep!). After restarting the computer, since there was no automatic identification request, I de-abilitate the cable connection. But this time I didn't find any way to rehabilitate it! Do you have any suggestions on how to solve the problem? My "Wired AutoConfiguration" has the startup type "Automatic", but it's not enough to restart automatically the cable connection! I tried to do some standard things like restart the computer, unplug and plug in again the cable, reinstall the web-connection from the scratch... But nothing worked! Thank you very much for your help!

    Read the article

  • Router drops internet connection if I connect an additional pc

    - by BluePerry
    Hey, I'm using a SMC2804WBRP-G router connected to my ADSL-modem. Usually there are two computers connected to this router: a win7 ultimate desktop(wired) and a macbook air (wireless). Both working absolutely fine and never caused any connection drops as far as I know. A new room mate moved in last month and each time she starts up her win7 home laptop the router looses the internet connection. The laptop is on a wired connection. The first time she connected to my router, the connection dropped every 2 mins. To find out whats wrong with her machine I disabled all unnecessary services etc. besides the anti virus software. That helped to eliminate almost all of those periodic connection drops. But the start up drop remained and I've got the feeling that the router is still loosing connection from time to time. I haven't had the time to find out what service caused the periodic drops. But I'm more concerned about is that start up drop. Can anyone point me in the right direction to look for the problem? I would be very thankful for any hints or tips!

    Read the article

  • Could anyone help me get my NETGEAR WNA3100 (Broadcom BCM43231) wireless adapter to work?

    - by Matthew Carroll
    I have just moved back to Ubuntu from Windows 7 and a few months ago, I bought a NETGEAR WNA3100 wireless adapter because my old adapter had broken. I plugged in my adapter and it doesn't seem to work, I also used the windows 7 drivers for it and tried them on the program "Windows Wireless Drivers" and they don't seem to recognize the device. However I have heard you need XP drivers but I can't seem to find them on the internet nor find them on the CD. Could anyone help me get my wireless adapter to work? Any help is greatly appreciate. P.S I do have internet connection though I have to tether my phone to my computer and then connect my phone to my router.

    Read the article

  • Is the wireless driver from Live USB different from the standard install?

    - by Rafael Magalhães
    Linux newbie here. I've been trying to use Ubuntu (x64) as my main OS since 11.10, but my wireless connection on it has been very unstable, droping every other 5-10 mins. For this reason I see myself forced to use Windows 7 (dual booting), where connection works flawlessly -- which really bothers me. My card is an Atheros 9k, which claims a reasonable amount of wireless complaints on Ubuntu forums. I've tried every suggestion given on past questions to this site but to no avail. However, while running Ubuntu Live USB for some of the tests, I noticed that my wireless connection never failed on it and wondered if its network configuration differs from the one on the default Ubuntu install. If this is the case, how could I reproduce the Live USB network environment on my hard drive install?

    Read the article

  • My wireless/WiFi connection does not work. What can I do?

    - by Wild Man
    Your situation You have successfully installed Ubuntu. You have just downloaded and booted Ubuntu live media. The latest LTS (see also HWE) or latest non-LTS release are preferred. See the list of Ubuntu releases that are currently supported.) You upgraded your Ubuntu installation to the latest release that the software updater offered you. WiFi worked before, but not now on the new release. You migrated your existing Ubuntu installation to new hardware. Your problem The wireless of your laptop or dekstop is not working. You tried switching the wireless switch off and on and you tried rebooting several times, but you don't see any WiFi access points. You can see your wireless access point, but you cannot establish a connection. You want to analyze the problem, but you don't know where to start or what information you can provide. Related questions I have a hardware detection problem, what logs do I need to look into?

    Read the article

  • What software is responsible for connecting to the wireless net specified in /etc/network/interfaces?

    - by zuba
    I'm curious what software (package, utility in bin's) handle interface parameters in /etc/network/interfaces and decides to connect to the specified wireless net. I use wifi usb stick dlink DWL-110 attached to wlan0 with ndiswrapper driver. Sometimes wlan0 sees my wifi net - iwlist wlan0 scan shows it, but does not connect to it - iwconfig shows AP Not-Associated, until I replug the stick. Neither reinserting module with ndiswrapper, not ifdown/ifup or restarting networking helps. That is why I need to know what OS entity handles connection/reconnection to wireless net. EDIT: shame on me, I use wireless-tool package with wep encryption

    Read the article

  • A Single wireless network is not showing up in Ubuntu that used too, and other devices have no issue finding or connecting to it

    - by Kit Sunde
    Up until about a week ago I could connect to my wireless, but now I suddenly can't. Every other wireless in the area show up in the network manager. My kindle can connect to it, my friend can connect to it (in windows) without having connected to it before. My other netbook (Samsung NC10) can connect to it, but my other Samsung N150 now cannot even see it. I have tried deleting the old auto entry for it in the network manager Tried disabling and enabling both the networking and the wireless through the network indicator. Disabled the networking through the hardware shortkut key thing [fn] + [F9] Attempting to connect to it as if it was a hidden network. I'm at a loss, how would I go about debugging and unborking my computer?

    Read the article

  • Script to connect to hidden wireless network with static IP?

    - by nLinked
    Would like a script, when run, it should connect to a hidden wireless network with these details: SSID is "Wireless" Network is not broadcasting its SSID above (is hidden) WPA2-PSK, AES, password is "password" Static IP: 192.168.1.1 Def. gateway: 192.168.1.254 DNS: 192.168.1.254 No idea how to do this. But I do know the wireless interface is called wlan0 and I'm on Ubuntu 10.10. I don't want to use the built in Network Manager as it never auto-connects on startup. WICD doesn't work either. Any ideas most welcome.

    Read the article

  • Programmatically get the WLAN config of a machine and use netsh to setup new profile

    - by Maestro1024
    How can I programmatically get the wireless LAN configuration of a machine and use netsh to setup new profile? I am having trouble getting the netsh command to set the ssid of a new card. I installed the drivers and plugged it in. I see in ipconfig it says the "media is disconnected" (fair enough). I then send the following command netsh wlan connect name=profile1 ssid=myNetwork interface="Wireless Network Connection 2" problem is I get an error "There is no profile "profile1" assigned to the specified interface. What is a profile for a wireless card? What should I set it to? How can I get my SSID set and connected for the card?

    Read the article

  • DHCP over WiFi on CentOS 6 [closed]

    - by dongle26
    Using CentOS 6 I cannot get my WiFi interface to configure over DHCP. Here is my ifcfg-wlan0: This does not work (although it is correct): DEVICE=wlan0 BOOTPROTO=dhcp ONBOOT=yes HWADDR=xx:xx:xx:xx:xx:xx TYPE=Wireless This works: DEVICE=wlan0 BOOTPROTO=none ONBOOT=yes IPADDR=192.168.0.253 NETMASK=255.255.255.0 DNS1=192.168.0.99 GATEWAY=192.168.0.99 HWADDR=xx:xx:xx:xx:xx:xx TYPE=Wireless I don't want a static IP address, I want a DHCP assigned address. Update: Both of the above configs are correct. Please don't downvote, this really didn't work for me. It must be a bug in CentOS or my wireless driver. See my answer for details.

    Read the article

  • IPs on home network

    - by windchime
    I have a Linksys router and a Belkin wireless router at home. The Linksys router is connected to cable modem and two computers, as well as to the Belkin wireless router. A 3rd computer is connected to the Belkin router through Wifi. The IP addresses of the computers connected to Linksys are 192.168.1.101 and 192.168.1.102. The IP address of the Linksys router on LAN is 192.168.1.1. The IP address of the Belkin wireless router is 192.168.2.1(based on the 3rd computer's routing table) and the IP address of the 3rd computer is 192.168.2.5. If I ping 192.168.1.101 from 192.168.2.5, all are well. However, if I ping 192.168.2.5 from 192.168.1.101, Destination Host Unreachable. Why?

    Read the article

  • Internet Connectivity... Help please!

    - by James
    Hi. My Laptop is having trouble connecting to my wireless router. Other laptops are using the wireless, but it's not reached capacity. The laptop recognises (with a strong signal) that there is wireless internet, and I can connect via the router with a cable because this happens automatically. My problem is this... When I click "connect" (for example in the network and sharing centre), the dialogue box closes and nothing else happens - as though "connect" is being read as "exit". I am running Vista on a Toshiba Satellite Pro P300. Any help would be very much appreciated, Thanks

    Read the article

  • Can I create an Infrastructure access point from built-in WiFi (as opposed to Ad-Hoc) on Windows XP?

    - by evilspoons
    I want to use my Windows XP laptop as an access point. What I am trying to achieve is possible under Windows 7 with a myriad of utilities, but the wireless driver stack was different before Windows 7 and those specific APIs don't exist on XP. The reason behind me wanting to do this is that I would like my Android phone to be able to connect via WiFi to a network that is only hard-wired (reverse tethering). Unfortunately, my Android device (Galaxy S Captivate) does not support ad-hoc networks without a serious amount of screwing around. Is it possible to create an "Infrastructure" network with my Dell Latitude D830's built-in WiFi - a "Dell Wireless 1395 WLAN Card", which I am assuming is probably rebadged Broadcom, or is there some fundamental difference between a wireless adapter and an access point that would prevent this?

    Read the article

  • Can't enable wireless lan on Fujitsu Siemens A1665G with Ubuntu 11.10 installed

    - by Theo
    I saw my old Notebook yesterday and wanted to make that work again. On Windows XP the wireless worked still fine. Then I installed new Ubuntu 11.10 32bit and I'm sadly not able to make the wireless enabled. [I replaced Win XP entirely] lspci lists following network: 08:0a.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) So after recommendation from this link I installed the b43 firmware module. iwconfig prints the following: wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associatd Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management: off As you can see, my wireless lan adapter is not turned on. sudo iwconfig wlan0 txpower auto Doesn't change anything. Then I tried to make it work with rfkill. rfkill list 0: phy0: Wirless LAN Soft blocked: no Hard blocked: yes sudo rfkill unblock all rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes remains the same. The question is now, how I could enable the hard blocked wireless LAN. There is no hardware switch for wlan integrated. However there is a button to change the state. I always thought this would be software sided, but it seems to make some hardware changes as well... The wireless LED is also not blinking (as it did on windows xp) I reset bios and searched for some settings in there, but it has only a few options and nothing to do with wireless settings, nothing works here.. At last I tried to install the acer hotkeys but I was not able to manage that. I installed the acerhkgui package, but in initializing progress, it was not able to compile acer hotkeys for my machine. There was a message that asm/linkage.h was not found while compiling. Do you have any ideas what I could do to make this hard blocked stuff disabled and my wireless card work? PS: I also tried sudo rm /dev/rfkill and a reboot to reinit that stuff... No success :(

    Read the article

  • wireless blocked after installing ubuntu 12.04

    - by Cornelia Frank
    I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

    Read the article

  • Cannot connect to MySQL over TCP locally - Connection Timeout - Ubuntu 9.04

    - by gav
    I am running Ubuntu and am ultimately trying to connect Tomcat to my MySQL database using JDBC. It has worked previously but after a reboot the instance now fails to connect. Both Tomcat 6 and MySQL 5.0.75 are on the same machine Connection string: jdbc:mysql:///localhost:3306 I can connect to MySQL on the command line using the mysql command The my.cnf file is pretty standard (Available on request) has bind address: 127.0.0.1 I cannot Telnet to the MySQL port despite netstat saying MySQL is listening I have one IpTables rule to forward 80 - 8080 and no firewall I'm aware of. I'm pretty new to this and I'm not sure what else to test. I don't know whether I should be looking in etc/interfaces and if I did what to look for. It's weird because it used to work but after a reboot it's down so I must have changed something.... :). I realise a timeout indicates the server is not responding and I assume it's because the request isn't actually getting through. I installed MySQL via apt-get and Tomcat manually. MySqld processes root@88:/var/log/mysql# ps -ef | grep mysqld root 21753 1 0 May27 ? 00:00:00 /bin/sh /usr/bin/mysqld_safe mysql 21792 21753 0 May27 ? 00:00:00 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --skip-external-locking --port=3306 --socket=/var/run/mysqld/mysqld.sock root 21793 21753 0 May27 ? 00:00:00 logger -p daemon.err -t mysqld_safe -i -t mysqld root 21888 13676 0 11:23 pts/1 00:00:00 grep mysqld Netstat root@88:/var/log/mysql# netstat -lnp | grep mysql tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 21792/mysqld unix 2 [ ACC ] STREAM LISTENING 1926205077 21792/mysqld /var/run/mysqld/mysqld.sock Toy Connection Class root@88:~# cat TestConnect/TestConnection.java import java.sql.Connection; import java.sql.DriverManager; import java.sql.SQLException; public class TestConnection { public static void main(String args[]) throws Exception { Connection con = null; try { Class.forName("com.mysql.jdbc.Driver").newInstance(); System.out.println("Got driver"); con = DriverManager.getConnection( "jdbc:mysql:///localhost:3306", "uname", "pass"); System.out.println("Got connection"); if(!con.isClosed()) System.out.println("Successfully connected to " + "MySQL server using TCP/IP..."); } finally { if(con != null) con.close(); } } } Toy Connection Class Output Note: This is the same error I get from Tomcat. root@88:~/TestConnect# java -cp mysql-connector-java-5.1.12-bin.jar:. TestConnection Got driver Exception in thread "main" com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: Communications link failure The last packet sent successfully to the server was 1 milliseconds ago. The driver has not received any packets from the server. at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at com.mysql.jdbc.Util.handleNewInstance(Util.java:409) at com.mysql.jdbc.SQLError.createCommunicationsException(SQLError.java:1122) at TestConnection.main(TestConnection.java:14) Caused by: com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: Communications link failure The last packet sent successfully to the server was 0 milliseconds ago. The driver has not received any packets from the server. at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at com.mysql.jdbc.Util.handleNewInstance(Util.java:409) at com.mysql.jdbc.SQLError.createCommunicationsException(SQLError.java:1122) at com.mysql.jdbc.MysqlIO.<init>(MysqlIO.java:344) at com.mysql.jdbc.ConnectionImpl.createNewIO(ConnectionImpl.java:2181) ... 12 more Caused by: java.net.ConnectException: Connection timed out at java.net.PlainSocketImpl.socketConnect(Native Method) ... 13 more Telnet Output root@88:~/TestConnect# telnet localhost 3306 Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection timed out

    Read the article

  • SQL connection to database repeating

    - by user175084
    ok now i am using the SQL database to get the values from different tables... so i make the connection and get the values like this: DataTable dt = new DataTable(); SqlConnection connection = new SqlConnection(); connection.ConnectionString = ConfigurationManager.ConnectionStrings["XYZConnectionString"].ConnectionString; connection.Open(); SqlCommand sqlCmd = new SqlCommand("SELECT * FROM Machines", connection); SqlDataAdapter sqlDa = new SqlDataAdapter(sqlCmd); sqlCmd.Parameters.AddWithValue("@node", node); sqlDa.Fill(dt); connection.Close(); so this is one query on the page and i am calling many other queries on the page. So do i need to open and close the connection everytime...??? also if not this portion is common in all: DataTable dt = new DataTable(); SqlConnection connection = new SqlConnection(); connection.ConnectionString = ConfigurationManager.ConnectionStrings["XYZConnectionString"].ConnectionString; connection.Open(); can i like put it in one function and call it instead.. the code would look cleaner... i tried doing that but i get errors like: Connection does not exist in the current context. any suggestions??? thanks

    Read the article

  • networking with ssh thru wireless

    - by nkvnkv
    I am using Ubuntu 12.04 64bit on my desktop and my laptop. Have install openssh client and server on both of them. My desktop is connected to ADSL2+ Router TD-8840 with wired connection and has 192.168.1.1 IP address. My laptop is connected to 150Mbps Wireless N Router TL-WR741ND with wireless connection and has 192.168.0.1 IP address. ADSL2+ Router TD-8840 and 150Mbps Wireless N Router TL-WR741ND are connected with a wired cable by useing blue port for on wlan on TL-WR741ND. ifconfig from desktop desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:92:37:1f:3d inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:92ff:fe37:1f3d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57508 errors:0 dropped:0 overruns:0 frame:0 TX packets:44508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:51547633 (51.5 MB) TX bytes:6371374 (6.3 MB) Interrupt:43 Base address:0x6000 eth1 Link encap:Ethernet HWaddr 00:23:cd:b1:ff:e4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:22 Base address:0x8400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:109 errors:0 dropped:0 overruns:0 frame:0 TX packets:109 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12044 (12.0 KB) TX bytes:12044 (12.0 KB) ifconfig from laptop laptop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:a0:d1:65:2a:42 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31244 (31.2 KB) TX bytes:31244 (31.2 KB) wlan0 Link encap:Ethernet HWaddr 00:19:d2:1b:19:81 inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::219:d2ff:fe1b:1981/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1590 errors:0 dropped:0 overruns:0 frame:0 TX packets:1276 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:874763 (874.7 KB) TX bytes:315401 (315.4 KB) I can connect to desktop from laptop via ssh with no problem, internet connection on laptop and desktop is working fine, but when I want to connect to laptop from desktop via ssh in terminal I type ssh [email protected] and get ssh: connect to host 192.168.0.101 port 22: Connection timed out If anyone is able to point out whats wrong?

    Read the article

  • Problems with wireless file copy - hangs during copy

    - by Eran Kampf
    I have this problem on my home network where when I try to copy files via wireless connection, at some point the copy fails and the machine doing the copy loses connection to the network. I'm pretty much lost as to figuring out the source for the problem... Some more details that might help: It's not OS related. I have Windows 7 machines and Leopard machines and this occurs on both I'm using a 3com OfficeConnect router Wired transfer works fine Other programs that require heavy wireless traffic work just fine:streaming large HD movies, Xbox Live! ... I'm lost as to how to even begin trying to diagnose the problem so any tips are welcome...

    Read the article

  • Wireless network not working Linux Mint

    - by zharvey
    I have a home LAN that I am confident is working properly (I have a Windows 7 and an Ubuntu Desktop machine that both see the router and a working Internet connection). I just installed Linux Mint (Maya) on a new machine and although I can connect to the Internet via a wired (ethernet) connection, it does not see my wireless network. In fact, as you can see in the screenshot below, it doesn't even look like it has the drivers to be able to detect a wireless network... I have ran update manager and made sure that I am up-to-date with everything and have restarted. Any ideas here?!?

    Read the article

< Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >