Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 32/286 | < Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >

• Cisco Linksys AE2500 wireless adapter not working

  - by makuto

  I have a Cisco AE2500 I've used with my laptop to get internet. I had to install the drivers by following this forum: http://ubuntuforums.org/showthread.php?t=1805830 But now the blue light on the adapter doesn't turn on at all, but ndiswrapper reports it is connected. I have no connection to the internet on my laptop, and the adapter doesn't show it's blue light on any of the USB ports of my computer or on the 4 port hub I have. Is there some way I can reset something so that the blue light will show again? I'm using Ubuntu 11.10 on a Dell Latitude D505 laptop. EDIT: I deleted and reinstalled the same exact driver and everything worked again.

  Read the article

• wireless driver error after install

  - by James

  after following this command to update wifi drivers:1- Boot into Ubuntu 2- Open a terminal by pressing Ctrl+Alt+T 3- Type in the following (verbatim!) sudo apt-get update && sudo apt-get upgrade press Enter, the command will prompt for your password (the one you use to login into Ubuntu), type it and press Enter. Wait for it to finish updating your system. Now type: sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer Wait for the command to finish installing the driver, when done restart your computer. i get a message after the first command when installing has done saying not enough space so it aborts! what do i do to fix this

  Read the article

• Wireless USB Adapter driver configuration

  - by Jones

  First I would like agree one thing that this is fully for Ubuntu, not for BackTrack. However I'm posting my BackTrack question here since I find similar problems in backtrack forum are being unanswered and Linux/Unix site of StackExchange has very low attraction. I'm having USB wifi adapter (iBall Baton), having chipset RTL8191SU. It displays available wifi networks in Wicd manager. But while trying to connect it gives me bad password. When I'm trying to run airmon-ng it didn't returned me the monitor mode. I tried to replace with Ubuntu 12.10 drivers. But it totally nulled the device functionality. However I restored the drivers. I'm interested to compile drivers as if anyone indicate the methods. Awaiting ideas!

  Read the article

• Really slow wireless internet on 12.04 with HP dv6 6070ca

  - by Joe

  I was recently running the previous version of Ubuntu through Wine, and everything was working great. I decided to upgrade to pangolin when I saw it came out. After upgrading the internet was very slow (the estimated time on the updates was something like 4 days). I thought maybe this had something to do with the Wine installation, so I decided to finally do an actual dual boot. I partitioned my drive all nice and neat, but I made the mistake of connecting to the internet for the installation, and clicking the option to install updates and restricted extras. This was in the morning, circa 6 am. Fast forward to the evening, the installation is frozen at around 75%. In frustration I gave the ol girl a hard shut-down, which effectively rendered my machine useless. I used the thumb drive to reinstall Ubuntu, this time without connecting to the internet. Installed nice and easy, no problems, but the internet is still ridiculously slow. It took me about 20 minutes of frustration and hitting stop and reload repeatedly to even get this question page to open. This is important to me as now Windows won't even boot and I have to use ubuntu for the time being but I can't even bear to turn on my laptop due to the frustration that immediately ensues. Please help! Oh, and I'm relatively new so if there are some terminal commands that spew out info you guys would find useful let me know what they are and I'll post back the information.

  Read the article

• Help setting up wireless in Ubuntu 13.04

  - by James

  I'm having problems connecting my WIFI in Ubuntu 13.04 . So I was wondering if filling in the data manually ie: the IPv4, IPv6, the SSID and BSSID info etc. I did try this before but maybe I put in the wrong data or maybe not enough. Would that make it work? I just don't know how to find out some of the data you need to put in? I'm new and it's confusing. Does anyone know the solution? Here is lspci: james@james-MM061:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 01) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 01) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01) 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) 0b:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) Computer information: Model: Dell MM061 Mobile Intel(R) 945GM Express Chipset Family [Display adapter] (2x)

  Read the article

• Broadcom 4365 wireless driver on 12.04 with 3.4 / 3.5 kernel

  - by zaid

  I used this package to install the driver on 3.2 Kernel and it was working perfectly. Unfortunately the system used to freeze randomly with 3.2 kernel so I installed 3.4 kernel, now there is no freezing, the only problem is that my wifi card is not working, I tried to re-install the package, but didn't work. I can see the driver in the "additional drivers" and it say that it is active, but when I execute iwconfig it doesn't show up. I've even tried ndiswraper and that didn't work either. my lspci: 01:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01)

  Read the article

• Pppoe wireless connection, Ubuntu 12.4

  - by Barbara

  I recently bought a new computer (Asus 1015 cx) with Ubuntu (12.4) as preinstalled system. My problem is with the internet. The computer connects just fine to the free wifi we have at home, but in college, we have a little bit different system. There is wifi, but it is not free - everyone receives a user name and a password. I cant manage to estabilish this Pppoe connection - the computer "sees" where can it connect, but I dont know where to write my username and password. It is not the DSL connection, what I have already tried. Can you help me?

  Read the article

• Connectify-like functionality on 4965 AGN wireless?

  - by Vivek Sharma

  I would like to use my laptop as an Access point, so that i can connect my phones through Wifi. I have done this my office laptop T410. I am having T61 with wifi module 4965. Connectify on windows does not support it. I am following these instructions to make achieve WAP capability on my T61 running ubuntu 10.10. The link says something about "master mode", how do i put my T61 wifi-inter4965 in master mode. Can I install madwifi or atheros drivers on it? I am using galaxy S froyo, and it does not support Ad-hoc network. Has anyone tried to achieve this?

  Read the article

• 12.10 Wireless networking

  - by user108594

  I downloaded ubuntu 12.10 using WUBI and cannot connect to the internet. I removed it and downloaded ubuntu 12.04 still cannot connect. This I assume rules out the program being the problem. I reinstalled 12.10. When loaded I get the same message W/red (x) stating Internet not connected. I went to the Settings drop down box and it does not reveal the network list but (enable networking has a ck mark). Am running a HP Laptop with a w/7/64 OS that has a kill switch that indicates (orangeno connection) I downloaded 12.10 on my desktop (on the same network) and everything OK. I tried to follow the instructions in the help menu but got lost and confused . Sincerely Dan Additional Info per request Broadcom 802.11b/g Wlan Internal pc [hp laptop] P.S. I've been out of town for about a month. TKS for your gitback I did install 12.10 via cd and everything ok,but retried alongside 7 and unable to connect to internet,also took laptop and hard wired using ethernet cable and everything ok. stumped again and running out of ideas!!!

  Read the article

• Getting wireless to work on Ubuntu 11.10 (on a mac machine)

  - by yayu

  I have a 2008 white 13.3 inch macbook that now solely runs ubuntu. However, I cannot get wifi or cable to work on it. Regarding the cable, it atleast tries to connect but eventually disconnects from the wired network. Here is the output for lspci (pastebin) I tried installing b43-fwcutter and firmware-b43 but get errors. (I loaded them from a thumb drive and tried sudo dpkg -i). I cannot understand these instructions from the documentation, as I cannot locate the pool directory. b43-fwcutter is located on the Ubuntu install media under ../pool/main/b/b43-fwcutter/ and patch is located under ../pool/main/p/patch/ or both in the official repositories online. Note: In some versions (10.04 and 11.04 at least) there is not a /pool/main/p/patch/ If this file is missing then you don't need it. In this case you only need to install /pool/main/b/b43-fwcutter by following the instructions below.

  Read the article

• Ubuntu 12.04 - no wireless network recognized

  - by Itai

  I just installed Ubntu 12.04 along with WIN7 on the same laptop - Dell Vostro-3560. Now, on Win7 i can access to different wi-fi networks. However, when i am logging onto the Ubuntu section (after re-starting my laptop) - an error message appears: "Disconnected - you are now offline". When i take a look at my network menu (in the upper bar on the screen), i see that no network is found (and i have a few of them in the area...). I tried to look around but really could not find a concrete practical solution to this specific problem, would appreciate any solution from anyone out there that had this problem and solved it. Thanks... Itai

  Read the article

• Wireless is connected, but can't browse the Internet (or connection goes completely)

  - by user261007

  I'd like some help with this, please. Will be very glad is anyone will point me in the right direction. Thank you in advance! This is when the connection is present and browsing: eth0 Link encap:Ethernet HWaddr 50:46:5d:4a:9e:4f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2666 errors:0 dropped:0 overruns:0 frame:0 TX packets:2666 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:228844 (228.8 KB) TX bytes:228844 (228.8 KB) wlan0 Link encap:Ethernet HWaddr dc:85:de:1c:91:f9 inet addr:192.168.1.147 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::de85:deff:fe1c:91f9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18780 errors:0 dropped:0 overruns:0 frame:0 TX packets:12817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21198762 (21.1 MB) TX bytes:1746891 (1.7 MB) When connection goes: wlan0 Link encap:Ethernet HWaddr dc:85:de:1c:91:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:209503 errors:0 dropped:0 overruns:0 frame:0 TX packets:132560 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:268811733 (268.8 MB) TX bytes:15479814 (15.4 MB)

  Read the article

• My wireless connection isn't working well

  - by Maikel Braas

  So this is my problem, I intalled ubuntu 12.04 with the wubi.exe and everything works fine, but my internet connection. When I try to install a program or use firefox, it goes with 24kb/s with a little luck for 1-2 seconds and then my internet terminates and it starts up again after 3-5 mins. Then it goes with an other 24kb/s and this will repeat. The thing is my connection works perfectly with windows. The laptop its running on is a Acer ASPIRE V3-771G. I tryed using a different network adaptor but that didn't help either. Please, some one help me with this. friendly regards, Maikel

  Read the article

• ASUS VX-6 Laptop Wireless not connecting

  - by user2152790

  Someone posted a script a couple days ago, here is my output.Pastebin I can see wifi SSIDs in network, but cannot connect to mine. The only time wifi worked on 13.10 was in the Live CD, but wifi stopped working as soon as install process started. Did below but made no difference. sudo apt-get install bcmwl-kernel-source sudo modprobe -rv brcmsmac sudo modprobe -v wl What I do next? I tried Software&Updates and it showed 1 proprietary driver in use. This sounds like a WPA/WPA2 issue? Wifi works when I tried Zorin OS 7.1, wifi always worked in windows 7.

  Read the article

• Linux does not connect to wireless network under Hyper-V with Windows 8

  - by Graznarak

  I have a VM I am trying to run under Hyper-V on Windows 8 Pro. I am using an Asus PDE-N15 adapter on the host machine. When I run Windows 8 in the VM it connects to the network and everything works. When I use Linux (Ubuntu 13.04 32-bit, Ubuntu 13.04 64-bit, Fedora, CentOS) it will not connect to the network. When I run ifconfig I see the adapter show up as eth0 with the correct HWaddr. I see that TX bytes 0, and RX bytes == 0. Could anyone help me figure out how to get this to work?

  Read the article

• Could not find DHCP daemon to get information on Belkin G Wifi Router

  - by Anirudh Goel

  I am using a Belkin G Wireless Router F5D7234, and i have a DSL connection with only a ethernet cable. So i connected the cable to the Modem port and allowed it to use Dyanmic IP, it worked successfully and an ip was assigned to it and multiple computers could connect to it and browse. But after some time the power went off and after then upon rebooting it is taking about half hour to get an IP address. Upon seeing the log i see this entry repeatedly 07/02/2010 23:22:34 DHCP Client: [WAN]Could not find DHCP daemon to get information 07/02/2010 23:22:32 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:30 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:28 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:26 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:26 DHCP Client: [WAN]Could not find DHCP daemon to get information 07/02/2010 23:22:24 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:22 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:20 DHCP Client: [WAN]Send Discover 07/02/2010 23:22:18 DHCP Client: [WAN]Send Discover Any idea what i can do? I tried using another belkin router of same model and make and there also i faced the same problem.

  Read the article

• win xp wifi networking

  - by user3485532

  I have 2 pcs with win xp and a wifi router ( without outgoing internet connection )...my job was to connect them over wifi to share some files. router was properly configured, both computers connected to wifi without problems, but when I tried to network them I could not see them in workgroup...i changed their names and added them to same workgroup but i couldn't connect pc1 to pc2 ( i could ping router from each pc but pinging other computer resulted in ping timeout) ..now i cant figure out why this is not working since I've done this before on more complex networks and it should work but...( maybe I have gremlins hiding somewhere..) edit1: Firewall is down on both machines( I disengaged it in both control panel and in services) and folder sharing and permissions are ok.. edit2: I know about Ad Hoc network ( wlan-to-wlan, without router/switch ) but that's not what I am trying to accomplish here :)

  Read the article

• Apache port forwarding with ZTE ZXV10 W300 router (provider specific firmware)

  - by dannote

  I'm trying to configure port forwarding for Apache 2.2 installed on Windows XP SP3 with ZTE ZXV10 W300 router. The computer has a static IP 192.168.1.2. Port forwarding is configured as following: Enable true Name Apache Protocol TCP (also tried TCP and UPD) WAN Host Start IP Address empty WAN Host End IP Address empty WAN Connection stream WAN Start Port 8080 WAN End Port 8080 LAN Host IP Address 192.168.1.2 LAN Host Start Port 8080 LAN Host End Port 8080 Port 8080 is open for both TCP and UPD in Windows Brandmauer. Apache configuration: Listen 192.168.1.2:8080 Router Firmware: Hardware Version V1.0.01 Software Version V8.0.02T03_CFA Boot Loader Version V1.1.2 The provider is COMSTAR. I'm not sure but it's said they flash routers with modified firmware. I have also tried to set up Bitcomet port forwarding on port 13514 and failed.

  Read the article

• Port-forwarding on livebox to router

  - by Yusuf

  Hello, At home, I have two routers, one Livebox and a Netgear. The reason why I need the Livebox is that the phone line cannot be connected to the Netgear router. So I have the Livebox connected to the phone line, the Netgear connected to the Livebox, and all PCs connected to the Netgear. My issue is that for every application or port that I want to give external access, I have to create entry in both the Livebox and the Netgear routers; so I would like to know if there's a way to automatically forward all requests to the Netgear router, from which I will then forward to the required IP:port. Thanks in advance.

  Read the article

• Cannot access router outside of network

  - by Andrew

  My router's ip cannot be accessed using my phone. It just says server not found.

  Read the article

• Cannot access router outside of network

  - by Andrew

  My router's ip cannot be accessed using my phone. It just says server not found.

  Read the article

• networking router source of packet loss and transmission delays

  - by Nitesh

  Why are router source of packet loss and transmission delays?

  Read the article

• Apache port forwarding with ZTE ZXV10 W300 router (provider specific firmware)

  - by dannote

  I'm trying to configure port forwarding for Apache 2.2 installed on Windows XP SP3 with ZTE ZXV10 W300 router. The computer has a static IP 192.168.1.2. Port forwarding is configured as following: Enable true Name Apache Protocol TCP (also tried TCP and UPD) WAN Host Start IP Address empty WAN Host End IP Address empty WAN Connection stream WAN Start Port 8080 WAN End Port 8080 LAN Host IP Address 192.168.1.2 LAN Host Start Port 8080 LAN Host End Port 8080 Port 8080 is open for both TCP and UPD in Windows Brandmauer. Apache configuration: Listen 192.168.1.2:8080 Router Firmware: Hardware Version V1.0.01 Software Version V8.0.02T03_CFA Boot Loader Version V1.1.2 The provider is COMSTAR. I'm not sure but it's said they flash routers with modified firmware. I have also tried to set up Bitcomet port forwarding on port 13514 and failed.

  Read the article

• Why is my router assigning the wrong address via DHCP

  - by Barry

  I have a WRT54G router that is set up to serve out addresses via DHCP. It correctly serves up addresses to every other machine on the network, including another PC, my macbook when connected via wireless, my wife's notebook, and our printer. However, whenever I attach my macbook to the router via an ethernet cable, the address it is given via DHCP is wrong. My local network is set up as 192.168.1.*. However, when my macbook connects with an ethernet cable, it is given the IP 192.168.29.*. Currently, I have the macbook set up with a manual IP address, and all seems to be working fine. Any ideas on what could be causing this?

  Read the article

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

< Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >