Search Results

Search found 12038 results on 482 pages for 'controller actions'.

Page 320/482 | < Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >

• How can I accurately determine the age of a hard drive?

  - by Todd Stout

  Yes, if it's large, heavy, and only 65 Meg in capacity, you can assume it's ancient. An RLL controller would positively indicate the drive is from antiquity. What about drives that are only 3 or 4 years old? If I know the serial number, make and model is there a public database that indicates a manufacturing date? Update: As trite as this question might seem to some, the hard drive I was looking at that precipitated this question had no obvious manufacturing date stamped on it. I realize that most do. I think the answers given are very useful to myself and others.

  Read the article

• Jumbo Frames on DIR-655

  - by Spookyone

  Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Active Directory: trouble adding new DC

  - by ethrbunny

  I have a domain with 3 DCs. One is starting to fail so I brought up a new one. All are running Win 2003. Problem: there appear to be replication issues between the 4 machines but I can't figure out what's causing this. All are registered with the DNS as identically as I can make them. How do I know there is a problem? Nagios is telling me that the other 3 DCs are having KCCEvent errors and the new machine is reporting "failed connectivity" errors. Doing dcdiag on the new machine reports: the host could not be resolved to an IP address. This seems crazy as I log into it using the DNS name. I can ping it from the other three machines using this DNS name as well. repadmin /showreps from the new machine says its seeing the other 3 machines. Doing the same from one of the older machines doesn't show the new machine. I've tried netdiag /repair numerous times. No luck. There are no firewalls running on any of the machines. If I look at Domain info via MMC (on the new machine) it appears that all the information is current. Users, computers, DCs.. its all there. Im puzzled as to what step(s) I've missed in adding this new machine. Suggestions? EDIT: dcdiag from non-working: C:\Documents and Settings\Administrator.BME>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\YELLOW Starting test: Connectivity The host 312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu could not be resolved to an IP address. Check the DNS server, DHCP, server name, etc Although the Guid DNS name (312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu) couldn't be resolved, the server name (yellow.server.edu) resolved to the IP address (10.127.24.79) and was pingable. Check that the IP address is registered correctly with the DNS server. ......................... YELLOW failed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\YELLOW Skipping all tests, because server YELLOW is not responding to directory service requests Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck dcdiag from working: P:\>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\AD1 Starting test: Connectivity ......................... AD1 passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\AD1 Starting test: Replications ......................... AD1 passed test Replications Starting test: NCSecDesc ......................... AD1 passed test NCSecDesc Starting test: NetLogons ......................... AD1 passed test NetLogons Starting test: Advertising ......................... AD1 passed test Advertising Starting test: KnowsOfRoleHolders ......................... AD1 passed test KnowsOfRoleHolders Starting test: RidManager ......................... AD1 passed test RidManager Starting test: MachineAccount ......................... AD1 passed test MachineAccount Starting test: Services ......................... AD1 passed test Services Starting test: ObjectsReplicated ......................... AD1 passed test ObjectsReplicated Starting test: frssysvol ......................... AD1 passed test frssysvol Starting test: frsevent ......................... AD1 passed test frsevent Starting test: kccevent ......................... AD1 passed test kccevent Starting test: systemlog ......................... AD1 passed test systemlog Starting test: VerifyReferences ......................... AD1 passed test VerifyReferences Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck P:\>

  Read the article

• Cross-Forest Trust

  - by cdalley

  I am looking at testing a cross-domain trust we can have two domain controllers (with different forests and domain names) setup so we can move everyone onto the new domain. We do NOT run exchange on site and we do not have any links to O365 to AD currently. Onto the problem: I have setup two DCs in a Virtual Machine: They are on the same network 192.168.0.* The Windows 2003 server: Name: OLDSRVR "Clone" of our current Domain Controller IP: 192.168.0.1 Domain: internal.test.com The Windows 2012 server: Name: ADCTEST01 Brand new domain setup from scratch separate to internal.test.com Domain: internal.test2.com IP: 192.168.0.2 OLDSRVR can only see ADCTEST if it has dynamic IP set. If I set a static IP it cannot see it. If I try using the dynamic IP and try to join it gets to the end then complains "??The trust relationship between this workstation and the primary domain failed" Any ideas?

  Read the article

• Terrible Performance with SATA Drives on Dell PowerEdge, steps to troubleshoot?

  - by Tom

  I had asked this question earlier and the question went missing so here it is again. Bought a DELL Poweredge 2950 to use as in-house QA Server. Disk performance is beyond terrible, 1000-4000 ms response time on the drive with our SQL Server database .mdf. Sql Server disk queue upwards of 300 at times. I'm a software guy, can anyone help me with steps to determine the issue? I don't know what RAID controller it has, how can I determine that? I'm speculating it could be BIOS issue. Perhaps the server used to have another kind of drive in it and when I added SATA the ??? buffer size is wrong??? Perhaps I chose wrong options (chose defaults) when setting up the RAID 1 arrays? I thought RAID 1 was a performance array?

  Read the article

• How difficult will it be to switch DHCP from Windows 2000 to our network router?

  - by MetalSearGolid

  While I know a bit about networking, I am more of a programmer, and I have never set up a DHCP server. I have always allowed a router to assign IP addresses. However, my boss has asked me to switch out our old Win2k Domain Controller and DHCP server to a new server. The catch is that he wants to just use our router to assign IP addresses rather than have the new server do it. Is this going to be more than just disconnecting the old server? And if so, are there any documents or tips anyone can help me to make the transition a bit smoother? The new server will most likely have Windows Server 2008 R2. Any advice I can get on this matter would be greatly appreciated.

  Read the article

• OpenVPN Configuration - Windows 7 client & debian server

  - by Guillaume

  I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

  Read the article

• Why has ESXi 5.0 not used the software RAID configuration on my test server?

  - by kafka

  I've got a test server which was running WS 2008 Enterprise on the bare metal. It was correctly using the software RAID 1 configuration (2x250 GB disks which appeared as one disk), setup on the Dell Poweredge T110 (which meets compatibility requirements) without requiring any extra setup from me. (As an aside I'm fairly sure it's software RAID, as we didn't spec a hardware RAID controller, if that's of any importance in this situation). I am now testing installing ESXi 5.0 on this server to run some VMs. I've successfully installed ESXi, and imported a VM fine, but it's showing 2 x 250 GB disks available as datastores. However they should be appearing as one volume. When I boot the server, there is a RAID configuration screen you can enter, and I'm guessing this is what I'll have to do at some stage, but now need to be very careful because there is one disk which contains data that I want to be mirrored on the other disk. What is the best thing to do in this situation?

  Read the article

• Is there still a place for tape storage?

  - by Jon Ericson

  We've backed up our data on LTO tapes for years and it's a real comfort to know we have everything on tape. A sister project and one of our data providers have both moved to 100% disk storage because the cost of disk has dropped so much. When we propose systems to potential customers these days we tend to downplay or not mention our use of tape systems for data storage since it might seem outdated. I feel more comfortable with having data saved in two separate formats: disks and tape. In addition, once data is securely written to tape, I feel (perhaps naively) that it's been permanently saved. Not having to rely on a RAID controller to be able to read back data is another plus for me. Do you see a place for tape backup these days?

  Read the article

• How Can I prevent a specific application from being run on a specific machine using Group Policy?

  - by Mike

  I know this is possible to do and I am working on it with limited success. I believe the Group Policy I want is "Do Not Run Specified Windows Applications" - I can enable this and add the .exe I want to the list of programs not to be run. I have tried this on my local machine by running gpedit.msc going to User Config Admin Templates System and then choosing that policy and editing and enabling it. Doing it this way verifies that it works as I could then not run the specified .exe (XenAppWeb.exe) So this is great. I have created a GPO to do the same thing in GP Management on my domain controller where we centralize this, enforced it, applied it to an OU, and put one of our machines into this OU to test it. I have let it sit there for 3 days, run gpupdate /force, and when I try to run XenAppWeb.exe on this machine, it still lets me run it fine. What can I look at to troubleshoot this? I should note that I am trying to enact this policy on Windows XP machines (Virtual Machines) Thanks, Mike

  Read the article

• Red Hat 5.4 slow processing

  - by yucefrizk

  I'm running Red Hat Linux 5.4 on HP DL580 server with 16 processors and 64 GB of RAM. I'm connecting to the server remotely through SSH. after entering the password, it takes time to return the command line, if I click ctrl+c during this time, I'll have the command line prompt but not the correct bash prompt (I have to run bash to pass to my correct prompt). I tried to install Apache on the server, ./configure took 4 hours to finish instead of 1 or two minutes, Oracle installation same behavior. Server Disks are mirrored using RAID controller. any idea what could be the reason of this slowness?

  Read the article

• Windows 2003-R2-Server: Process "System" takes large chunks of CPU time

  - by Dabu

  I have a domain controller running 2003 R2. The server behaves very well when restarted daily, however, each day it is not restarted, there's a process called "System" that takes enourmous chunks of CPU time (up to 95%). The server supports AD, WINS, DNS, has Kaspersky Endpoint Security running, and manages backups via Arcserve 15. When I tried so far: Process Explorer (ex-Sysinternals) shows that the "System" process has no sub-processes. In the "Threads" tab of the detailled view I can see that 90% of the CPU time is used up by "ntkrnlpa.exe+0x803c0". The "Interrupts" process is running at 3-5% of CPU time, I'm not sure if this accounts for the amount of CPU time that System takes.

  Read the article

• SQL2005 reporting server: intense security activity

  - by David Wimbush

  On my reporting server the Security log shows large numbers of Logon/Logoff events, often 10 or more, when you run pretty much any report in the Report Manager. Is this normal or is it a classic sign of having the wrong setup? Some system details: Windows Server 2003 R2 SP2, virtual server running under VMWare). SQL Server 2005 SP3 Standard Edition, running databases, Report Manager, and Ananlysis Services cubes. No other major services on the machine (i.e. it's not a domain controller, Exchange server or anything like that). Any ideas, please, guys?

  Read the article

• USB forwarding from dom0 to domU

  - by Karolis T.

  What are my options to forward two USB connected phones to xen guest? I've read about PCI-passthrough http://www.wlug.org.nz/XenPciPassthrough, but I'm sure usb controller in the server isn't a pci card. There's device level forwarding, but I need to forward two devices, this here doesn't say how to do it: http://www.olivetalks.com/2008/02/03/usb-forwarding-on-xen-it-just-does-not-work/ Would something as simple as: usbdevice = [ 'host:xxx', 'host:yyy', ] work? EDIT: I'm now starting a bounty. This is really important for me and for other people also, hoping someone who have this resolved will be able to help.

  Read the article

• Multicasting Windows 7 Image

  - by LawnChairSkank

  I am trying to deploy some new machines with windows 7 for the first time in our computer labs. We used to use third party imaging software and then run sysprep after the image was copied(XP), but it seems you can't go that route with windows 7. We set up a new imaging server with the windows system image manager, but when we try to multicast the image it pretty much takes down our whole staff and faculty network. I heard you can turn on a multicast feature on our cisco switches to help with the issue, but that it also slows the switches to a crawl. Another idea we have tried was pulling the the computer lab switch off the main network and plugging the imaging server directly into the computer lab switch so the multicast doesn't take down our network, but it doesn't seem to work without being able to hit a domain controller. Is there a way to multicast without taking out the network? I feel like I am missing something... Thanks in advance

  Read the article

• Domain users sometimes cannot access our NAS

  - by Natalie

  I'm using a QNAP TS-410 Turbo NAS and I've got domain users connecting to it frequently everyday. However, there are times when their connection to the NAS will seem to just drop and, suddenly, they cannot access their network drives (which I had set up our Domain Controller to automatically map to folders on the NAS). Could you please tell me what may cause this? I don't think it is a network issue as everything else seems to work just fine. (If more details are needed, please let me know so I can update this question.)

  Read the article

• Certain drives in RAID 5 set intermittently are not recognized

  - by hydroparadise

  I have a curious problem in that 1 (sometimes 2) drives do not get recognized in a RAID 5 set. The server is getting rather old at 5 to 6 years, but still seems to function well once the machine sees all drives. So that leaves me with three areas to consider: the motherboard, the SATA RAID card, or the individual hard drives themselves. I am leaning toward the RAID card, but have not had much dealings with RAID cards. What would cause individual drives not to be recognized in the set? If it was the card, I would think that it would be all or nothing. If it were a single drive, is it possible that it would only work sometimes? The only other thing to consider is that that they are different drives (Seagate and Western Digital) but all around 80 GB. SATA RAID controller is 3ware Escalade 8506-4LP Motherboard is a SuperMicro P4SPA+ Am open and available for more details if needed...

  Read the article

• Ubuntu 11.04: No Audio Output

  - by Jason George

  I installed a fresh copy of Ubuntu 11.04 earlier this week and I'm having trouble getting my audio online. It was working fine in 10.04 and all the resources I can find on troubleshooting seem to be fairly dated so I'm not sure if they apply. CMI8788 [Oxygen HD Audio] Analog Stereo Duplex Playing a WMA file shows 0.00db output when I mouse over the sound controller in the status bar. Obviously, no output from my speakers. I tried adjusting the profile, thinking I might have the wrong one. That seems to have made things worse. Where mouse over originally said something along the lines of "Oxygen HD Audio," it now reads "Dummy Output." Selecting "Test Speakers" in sound preferences crashes the dialog. Any pointers would be great.

  Read the article

• Slow upload to Server 2008 DC, Downloads work as expected

  - by Anthony

  I have a Windows Server 2008 Domain Controller that I run as a do-it-all server. It has a GbE connection to the network and to every machine on the network. Downloads from the server file shares work as expected, between 70MB/s and 80MB/s to all the machines. However, when I try to copy files back up to the server, speeds fall to 7MB/s-10MB/s. I've disabled flow control and large send offload properties on all the NICs. I had this problem before and managed to fix it through some properties changes, but like an idiot, I never documented my fix and have since moved to a new server. Any ideas what I need to do to get the speeds to be more symmetric? EDIT: Remote differential compression is also disabled.

  Read the article

• Windows Server 2008 constantly spamming external IP's on outbound TCP port 445

  - by RSXAdmin

  Hi Server Fault, I have a Windows Server 2008 box running as a Domain Controller. I have noticed in my Cisco ASA firewall logs that this box is continuously sending out (like a thousand requests a second) requests on TCP port 445 to external hosts. I have made an effort to deny this outbound traffic from getting on the internet (using the ASA), however I would like these requests to stop from even occurring at all. I have tried disabling TCP/IP over NetBIOS. I have even turned on Windows Advanced Firewall on the box itself to block outbound 445 but the ASA still detects this particular traffic hitting it. I have other DC's and similar type boxes which are not behaving the same way as this box. Is this normal? Is there a way to stop this spamming? Have I been infected? Thank you universe.

  Read the article

• How do I determine which HD is involved in the Event Viewer?

  - by Rod

  My PC apparently crashed before I came home from work (so my daugthers tell me; they rebooted it). The first thing I did, after it came up, was got into the Event Viewer to see what it said. Several hours before they rebooted it, there's a message in the event viewer that says: The driver detected a controller error on \Device\Harddisk5\DR5 I've no idea what that means. I got into Computer Manager, to take a look at the disks on my machine. There's only 1 hard drive, and a few slots for microSD, etc, but none of them are labeled "Harddisk5", nor is there anything there labeled "DR5". How do I determine what, if anything, those are? Could they be USB drives that my daughters used?

  Read the article

• Active Directory: Find out which users belong to a Group Policy Object

  - by gentlesea

  Hi, I want to make sure that certain users are available in a group from the windows domain. I installed "Group Policy Management" and can open the Forest, the Domain. But then I am not sure what I am searching. I can select a link to a Group Policy Object (GPO). In Settings i see the Drive Maps and I know them. But how can I display a list of users that use this GPO? Right-click, Edit... is disabled. net group my_gpo does not work since I am not on a Windows Domain Controller. Any possibility to find out anyway?

  Read the article

• Linux: Automatically switch to external monitor (VGA)

  - by peoro

  I've got an eeePC with a really tiny monitor, so whenever I go (home, faculty, parent's home, friend's home, ...) I attach it to any external monitor I can find. If it matters my system is like this: Archlinux Linux 2.6.36 Xorg 7.6 X server 1.9.2 Intel Corporation Mobile 945GME Express Integrated Graphics Controller (fully accelerated by intel modules) When I boot up the system, it uses the integrated monitor (LVDS1) only, and I have to manually manually switch to the external monitor (VGA1) using xrandr. Is it possible to configure my Xorg (or whatever) so that it uses the VGA1 output if present?

  Read the article

• Transfer an account from a 'dead' domain

  - by PJC

  So - following from my previous question: How do I stop DFSR replication preventing a Domain Controller from advertising Domain Services?, I lost the FSMO DC, and my only other DC was in an unrecoverable state. I've created a new domain to continue my testing, but now have an issue which I suspect is relevant to any domain suffering a "catastrophe". I have user accounts and client PCs "on the old domain". (Actually 1 client PC and 3 accounts) I can still sign into the client PC as any of those users on the "dead" domain, because that is cached. There are (thankfully) no encrypted files in the "old" domain. What I would now like to do is migrate the full content (files, preferences, etc) from the "dead" domain to the new "live" domain for any/all user accounts, for the "old" PC. Is there anything out there which can assist me in doing so?

  Read the article

• How to identify RAID (5 or 6) controllers that allow dynamic resize of the array

  - by David Pfeffer

  I'm building a server with a RAID5 array, based on a hardware controller. I want to be able to later add additional disks and have the array rebalance across all of the disks, enlarging the usable size. I also want to be able to later upgrade to bigger disks (one at a time, of course) and then expand the array to fill the entire drive. These features are available in Linux software raid (md). I've also heard they're available in some hardware controllers. Currently, I own the Adaptec RAID 3805 card and the 3ware 9650se card. I'd prefer to use the Adaptec if possible, but I can't find if either of these cards offer this feature. If they don't, are there other affordable (read as: sub-$600) RAID cards available that can accomplish this?

  Read the article

< Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >