Search Results

Search found 40031 results on 1602 pages for 'command message'.

Page 321/1602 | < Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >

• Cannot format SD memory card

  - by cool

  Hello everyone I have a SD memory card which is of local manufacturer it allows to read & copy from it but not write as it is now write-protected so i want to format that card but could not. To format this card I have tried 1) DD command 2) mkfs -f vfat command 3) creating registry entry under storage device policy in window with write value 0 4) disk part command in window to clear attributes in which it show all attributes are clear ie no write protection 5) I format card in windows through control panel - administrative tools- computer management - disk management, then it show as formatted but when I tried to create new partition it give CYCLIC REDUNDANCY CHECK error 6) I downloaded a format utility from transcend site and formatted first it shows write protected again doing format it formats and tells to remove and reinsert after reinsertion it shows the previous data as it is

  Read the article

• FIX: Visual Studio Post Build Event Returns &ndash;1 when it should not.

  - by ChrisD

  I had written a Console Application that I run as part of my post build for other projects..  The Console application logs a series of messages to the console as it executes.  I use the Environment.ExitCode value to specify an error or success condition.  When the application executes without issue, the ExitCode is 0, when there is a problem its –1. As part of my logging, I log the value of the exit code right before the application terminates.  When I run this executable from the command line, it behaves as it should; error scenarios return –1 and success scenarios return 0.   When I run the same command line as part of the post-build event, Visual Studio reports the exit code as –1, even when the application reports the exit code as 0.   A snippet of the build output follows: Verbose: Exiting with ExitCode=0 C:\Windows\Microsoft.NET\Framework\v3.5\Microsoft.Common.targets(3397,13): error MSB3073: The command ""MGC.exe" "-TargetPath=C:\TFS\Solutions\Research\Source\Framework\Services\Identity\STS\_STSBuilder\bin\Debug\_STSBuilder.dll" C:\Windows\Microsoft.NET\Framework\v3.5\Microsoft.Common.targets(3397,13): error MSB3073:  C:\Windows\Microsoft.NET\Framework\v3.5\Microsoft.Common.targets(3397,13): error MSB3073: " exited with code -1. The Application returns a 0 exit code.  But visual studio is reporting an error.  Why? The answer is in the way I format my log messages.  Apparently Visual Studio watches the messages that get streamed to the the output console.  If those messages match a pattern used by visual studio to communicate errors, Visual Studio assumes an error has occurred in the executable and returns a –1.  This post details the formats used by Visual Studio to determine error conditions. In my case, the presence of the colon was tripping up Visual studio.  I Replaced all occurrences of colon with an equal sign and Visual Studio once again respected the exit code of the application. Verbose= Exiting with ExitCode=0 ========== Build: 3 succeeded or up-to-date, 0 failed, 0 skipped ==========

  Read the article

• PHP Mail() to Gmail = Spam

  - by grantw

  Recently Gmail has started marking emails sent directly from my server (using php mail()) as spam and I'm having problems trying to find the issue. If I send an exact copy of the same email from my email client it goes to the Gmail inbox. The emails are plain text, around 7 lines long and contain a URL link in plain text. As the emails sent from my client are getting through fine I'm thinking that the content isn't the issue. It would be greatly appreciated if someone could take a look at the the following headers and give me some advice why the email from the server is being marked as spam. Email from Server: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101784qeb; Thu, 15 Nov 2012 14:58:52 -0800 (PST) Received: by 10.60.27.166 with SMTP id u6mr2296595oeg.86.1353020331940; Thu, 15 Nov 2012 14:58:51 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id df4si17005013obc.50.2012.11.15.14.58.51 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:58:51 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Date:Message-Id:Content-Type:Reply-to:From:Subject:To; bh=2RJ9jsEaGcdcgJ1HMJgQG8QNvWevySWXIFRDqdY7EAM=; b=mGebBVOkyUhv94ONL3EabXeTgVznsT1VAwPdVvpOGDdjBtN1FabnuFi8sWbf5KEg5BUJ/h8fQ+9/2nrj+jbtoVLvKXI6L53HOXPjl7atCX9e41GkrOTAPw5ZFp+1lDbZ; Received: from grantw by dom.domainbrokerage.co.uk with local (Exim 4.80) (envelope-from [email protected]) id 1TZ8OZ-0008qC-Gy for [email protected]; Thu, 15 Nov 2012 22:58:51 +0000 To: [email protected] Subject: Offer Accepted X-PHP-Script: www.domainbrokerage.co.uk/admin.php for 95.172.231.27 From: My Name [email protected] Reply-to: [email protected] Content-Type: text/plain; charset=Windows-1251 Message-Id: [email protected] Date: Thu, 15 Nov 2012 22:58:51 +0000 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [500 500] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: grantw/from_h Email from client: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101495qeb; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received: by 10.182.197.8 with SMTP id iq8mr2351185obc.66.1353020089244; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id ab5si17000486obc.44.2012.11.15.14.54.48 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Content-Transfer-Encoding:Content-Type:Subject:To:MIME-Version:From:Date:Message-ID; bh=bKNjm+yTFZQ7HUjO3lKPp9HosUBfFxv9+oqV+NuIkdU=; b=j0T2XNBuENSFG85QWeRdJ2MUgW2BvGROBNL3zvjwOLoFeyHRU3B4M+lt6m1X+OLHfJJqcoR0+GS9p/TWn4jylKCF13xozAOc6ewZ3/4Xj/YUDXuHkzmCMiNxVcGETD7l; Received: from w-27.cust-7941.ip.static.uno.uk.net ([95.172.231.27]:1450 helo=[127.0.0.1]) by dom.domainbrokerage.co.uk with esmtpa (Exim 4.80) (envelope-from [email protected]) id 1TZ8Ke-0001XH-7p for [email protected]; Thu, 15 Nov 2012 22:54:48 +0000 Message-ID: [email protected] Date: Thu, 15 Nov 2012 22:54:50 +0000 From: My Name [email protected] User-Agent: Postbox 3.0.6 (Windows/20121031) MIME-Version: 1.0 To: [email protected] Subject: Offer Accepted Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: [email protected]

  Read the article

• NTP service, offset increasing after sync

  - by Ajay

  I have installed Ubuntu 12.10 version on my PC. I am running NTP service having NTP server as GPS. I found that when we start NTP service by ntp start command, PC is able to sync with GPS as i get '*' symbol before GPS IP when i run ntpq -p command. This remains good for some time and then the * symbol is removed which means that PC is not synchronized to that server. Now, by running command ntpq -p it shows that all parameter are OK but as '*' is removed, slowly offset goes on increasing. remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 7 16 1 2.333 23.799 0.808 remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 14 16 3 2.333 23.799 0.879 remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 11 16 7 2.333 23.799 1.500 remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 8 16 17 2.333 23.799 2.177 below are the last 4 ntp status when sync is lost with GPS ============================================================================== 192.168.100.33 .GPS. 1 u 1 16 377 2.404 1169.94 1.735 remote refid st t when poll reach delay offset jitter ============================================================================== 192.168.100.33 .GPS. 1 u - 16 377 2.513 1171.80 0.898 remote refid st t when poll reach delay offset jitter ============================================================================== 192.168.100.33 .GPS. 1 u 15 16 377 2.513 1171.80 0.898 Since, GPS is already available, PC never re-synchronize itself to GPS later ON. I have to restart the ntp service and then PC synchronizes to GPS and '*' symbol arrives.

  Read the article

• silent failure while creating odbc data source

  - by Peter

  I just got really confused trying to create an ODBC data source in Windows 2003 R2. I can create a connection to my chosen server (a MS SQL Server) on the "user DSN" tab, but when I try to do the same thing on the "system DSN tab", the process fails but without an error message. I am able to connect to the target database fine at the end of configuring a new data source, but when I click OK, the data source just isn't there. No error message, no sign that anything went amiss, other than the lack of a new data source. Very annoying, as I had to repeat the process a few times to make sure I wasn't crazy. Anybody got any hints? I suspect it is a permission problem of some sort but since there is no error message, I don't know where to start.

  Read the article

• How to stop a infinite running process(ztail) started by a ssh session after that session is closed

  - by Sanath Adiga

  I have a peculiar problem. My server supports multiple ssh session simultaneously, so that multiple admins can manage it simultaneously. We have a command which calls ztail to show the compressed log files and when the current ssh session is closed (without pressing ctrlc, to stop the tail command), the command should ideally stop working. But what I observed when I start a new ssh session is that the process ztail is still running in the background and consuming CPU, even though the previous session was closed. How can I determine when the session is closed, so that I can use that variable/flag to close/stop any commands initiated by that previously closed session?

  Read the article

• HP Printer scrolls "printing" forever - but nothing happens

  - by brett80

  I got a used HP Officejet 7130 all-in-one printer. I tried printing a text document, and it shows up in the queue (and says "printing"), and the printer display says "Printing" "Press Cancel to cancel job." - and it cyles that text forever, but nothing ever happens (after a couple of initial quiet noises.) I tried to print a test page from the printer, and I get the same "printing" message. I checked the hp website, and this problem is not on their list. (They are expecting a queue problem, error message, etc.) I did initially get a message that it needs new ink cartridges, but I pressed to get past that. It's supposed to try to print anyway. I don't want to buy ink cartridges for a printer that is broken. When I press it cancels correctly.

  Read the article

• How to install NPM behind authentication proxy on Windows?

  - by Tobias

  I need to run the latest version of Node and NPM on Windows. I installed Node 0.5.8 and downloaded the sources of NPM from GitHub. The steps I followed to install NPM were listed on its GitHub site but I have a problem running the following command: node cli.js install npm -gf but it fails with the following error message: Error: connect UNKNOWN at errnoException (net_uv.js:566:11) at Object.afterConnect [as oncomplete] (net_uv.js:557:18) System Windows_NT 5.1.2600 command "...\\Node\\bin\\node.exe" "...\\npm\\cli.js" "install" "npm" "-gf" cwd ...\npm node -v v0.5.8 npm -v 1.0.94 code UNKNOWN I think that this is a problem because I need authentication at my proxy to connect to the Internet. But I found no way to tell the installer to use my credentials for login. Is there a possibility to provide my proxy IP and login information to npm installation maybe via command-line arguments? I can provide the full log (but seems to have no more relevant information) using pastebin if needed.

  Read the article

• Resetting Update Manager

  - by Emre

  How can I fix Update Manager in 12.04, which hangs when I try to install any update, while sudo apt-get upgrade works fine? I suspect it has something to do with my python installation. This is the error message: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/defer/__init__.py", line 475, in _inline_callbacks result = gen.send(result) File "/usr/lib/python2.7/dist-packages/aptdaemon/client.py", line 1622, in _run_transaction_helper daemon = get_aptdaemon(self.bus) File "/usr/lib/python2.7/dist-packages/aptdaemon/client.py", line 1696, in get_aptdaemon False), File "/usr/lib/python2.7/dist-packages/dbus/bus.py", line 241, in get_object follow_name_owner_changes=follow_name_owner_changes) File "/usr/lib/python2.7/dist-packages/dbus/proxies.py", line 248, in __init__ self._named_service = conn.activate_name_owner(bus_name) File "/usr/lib/python2.7/dist-packages/dbus/bus.py", line 180, in activate_name_owner self.start_service_by_name(bus_name) File "/usr/lib/python2.7/dist-packages/dbus/bus.py", line 278, in start_service_by_name 'su', (bus_name, flags))) File "/usr/lib/python2.7/dist-packages/dbus/connection.py", line 651, in call_blocking message, timeout) dbus.exceptions.DBusException: org.freedesktop.DBus.Error.Spawn.ChildExited: Launch helper exited with unknown return code 1 Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/defer/__init__.py", line 475, in _inline_callbacks result = gen.send(result) File "/usr/lib/python2.7/dist-packages/aptdaemon/client.py", line 1622, in _run_transaction_helper daemon = get_aptdaemon(self.bus) File "/usr/lib/python2.7/dist-packages/aptdaemon/client.py", line 1696, in get_aptdaemon False), File "/usr/lib/python2.7/dist-packages/dbus/bus.py", line 241, in get_object follow_name_owner_changes=follow_name_owner_changes) File "/usr/lib/python2.7/dist-packages/dbus/proxies.py", line 248, in __init__ self._named_service = conn.activate_name_owner(bus_name) File "/usr/lib/python2.7/dist-packages/dbus/bus.py", line 180, in activate_name_owner self.start_service_by_name(bus_name) File "/usr/lib/python2.7/dist-packages/dbus/bus.py", line 278, in start_service_by_name 'su', (bus_name, flags))) File "/usr/lib/python2.7/dist-packages/dbus/connection.py", line 651, in call_blocking message, timeout) dbus.exceptions.DBusException: org.freedesktop.DBus.Error.Spawn.ChildExited: Launch helper exited with unknown return code 1 dbus.exceptions.DBusException: org.freedesktop.DBus.Error.Spawn.ChildExited: Launch helper exited with unknown return code 1 Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/defer/__init__.py", line 473, in _inline_callbacks result = gen.throw(result.type, result.value, result.traceback) File "/usr/lib/python2.7/dist-packages/UpdateManager/backend/InstallBackendAptdaemon.py", line 52, in commit downgrade, defer=True) dbus.exceptions.DBusException: org.freedesktop.DBus.Error.Spawn.ChildExited: Launch helper exited with unknown return code 1

  Read the article

• Why does Windows run CHKDSK on every boot?

  - by khris

  Every time I turn on my PC, I get the following message: Checking file system on E: The type of the file systen is NTFS. One of your disks need to be checked for consistency. You may cancel the disk check, but it is strongly recommended that you continue. Windows will now check the disk. CHKDSK is verifying files (stage 1 of 3)... 0 percent completed I allow CHKDSK to to complete, but Windows does not load. This message appears every time I boot my computer. Could someone explain me why this message appears and what I should do to make it disappear?

  Read the article

• Handling DataGrid.SelectedItems in an MVVM-friendly manner

  - by Laurent Bugnion

  An interesting question from one of the MVVM Light users today: Is there an MVVM-friendly way to get a DataGrid’s SelectedItems into the ViewModel? The issue there is as old as the DataGrid (that’s not very old but still): SelectedItem (singular) is a DependencyProperty and can be databound to a property in the ViewModel. SelectedItems (plural) is not a DependencyProperty. Thankfully the answer is very simple: Use EventToCommand to call a Command in the ViewModel, and pass the SelectedItems collection as parameter. For example, if the command in the ViewModel is declared as follows:public RelayCommand<IList> SelectionChangedCommand { get; private set; }and (in the MainViewModel constructor):SelectionChangedCommand = new RelayCommand<IList>( items => { if (items == null) { NumberOfItemsSelected = 0; return; } NumberOfItemsSelected = items.Count; }); Then the XAML markup becomes:<sdk:DataGrid x:Name="MyDataGrid" ItemsSource="{Binding Items}"> <i:Interaction.Triggers> <i:EventTrigger EventName="SelectionChanged"> <cmd:EventToCommand Command="{Binding SelectionChangedCommand}" CommandParameter="{Binding SelectedItems, ElementName=MyDataGrid}" /> </i:EventTrigger> </i:Interaction.Triggers> </sdk:DataGrid> I slapped a quick sample and published it here (VS2010, SL4 but the concept works in SL3 and WPF too). Cheers! Laurent Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

  Read the article

• Centos and dell PowerEdge Rxxx Series.

  - by OrenM

  hi we lately purchase few dell servers all of them from Rxxx series couple of R410 and R710 the OS we used on those servers is: CentOS 5.4 we're getting very weird error messages and we lost network connectivity couple of times (restarting the network interface was needed to fix it) the messages we're getting are: Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Uhhuh. NMI received for unknown reason 20. Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Do you have a strange power saving mode enabled? Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Dazed and confused, but trying to continue we have never seen those messages in the previous series of dell poweredge servers do someone here using centOS 5.4 on Rxxx series? did it happen to him too? maybe you have a suggestion about how to prevent it from happening

  Read the article

• "Disk boot failure" error after installing Windows 7 on SSD

  - by Tony_Henrich

  I have a system with 3 SATA drives which runs fine. Got a new SSD drive and wanted to install a fresh Windows-7 on it. So I removed the boot drive and replaced it with the SSD drive. Installed Windows and when it was done, rebooted and now I get "Disk boot failure. Insert system disk and press enter" error message. I reinstall again and still same message. Removed the SSD and put back the original drive and I got the same message!! I checked the BIOS and things look good. Something is wrong. Two questions: 1- Why isn't the new Windows booting from the SSD? 2- Why isn't the machine booting using the previous working configuration anymore, after removing the SSD? I did connect it during the second Windows installation but it was the last drive in the SATA connector. Would Windows installer mess with its MBR sector?

  Read the article

• wired connection not working in ubuntu 12.04 on lenovo G580 laptop

  - by shravankumar

  I found solution in http://www.zyxware.com/articles/2680/solved-wired-connection-eth0-not-detected-in-ubuntu-12-04 I downloaded compact-wireless-2012-07-03-p.tar.bz2 Here the steps i followed along with output 1. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ scripts/driver-select alx Output: Processing new driver-select request... Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk Backup exists: drivers/net/ethernet/atheros/Makefile.bk Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk 2.shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make output: make -C /lib/modules/3.2.0-23-generic/build M=/home/shravankumar/Desktop/compat-wireless-2012-07-03-p modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-23-generic' scripts/Makefile.build:44: /home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: *** No rule to make target `/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile'. Stop. make[3]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx] Error 2 make[2]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros] Error 2 make[1]: *** [_module_/home/shravankumar/Desktop/compat-wireless-2012-07-03-p] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-23-generic' make: *** [modules] Error 2 3. hravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make install output: FATAL: Could not open /lib/modules/3.2.0-23-generic/modules.dep.temp for writing: Permission denied make: *** [uninstall] Error 1 4. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ modeprobe alx output: No command 'modeprobe' found, did you mean: Command 'modprobe' from package 'module-init-tools' (main) modeprobe: command not found I am new to Ubuntu ,Please help me. Thanks in advance

  Read the article

• What value does SenderID provide over SPF and DKIM?

  - by makerofthings7

  I understand that SPF "binds" a message envelope to a set of permitted IP addresses. SenderID (with the default pra option) "binds" the message header to a set of permitted IPs in addition to the SPF logic. DKIM "binds" the from address header (and any additional header the sender chooses), and the body to a DNS Domain name I'm using the word "bind" above instead of "authorized" because it makes more sense (to me) Questions: If SPF is already verifies a message FROM in the envelope, why is there a need to check the headers? When would the need to verify the envelope (SPF) need to be different than the headers (SenderID) If I'm already verifying the headers with DKIM, why do I need SenderID? Most large companies I've checked don't disable SenderID with an explicit record. EBay is a notable example of one that does. What is the rationale for disabling SenderID "pra" processing of outbound messages?

  Read the article

• Synaptic won't launch from menu in panel in fresh Lubuntu minimal desktop 12.04 install

  - by ven42

  I performed a fresh install of Lubuntu 12.04 with minimal desktop, as described here: https://help.ubuntu.com/community/Lubuntu/Documentation/MinimalInstall. To clarify, I did a command-line install from the Lubuntu alternative install disc, then I did an "apt-get install --no-install-recommends lubuntu-desktop". Everything is working fine, except that Synaptic will not run from the menu entry in the panel. I am not prompted for a password, and no window of any sort appears after clicking the menu entry. I installed lxshortcut to see what the shortcut was running, and the command is "synaptic-pkexec". If I type this command into the "Run" menu, I get the same behavior (or lack thereof). I can get Synaptic to open up just fine by typing "gksudo synaptic" at the "Run" menu. Also, if I run "synaptic-pkexec" from the terminal, then I am prompted for my password within the terminal, and after that Synaptic opens normally. Can someone please suggest the right way to get Synaptic working? I could just change the menu entry to "gksudo synaptic", but I'm guessing that it's set to "synaptic-pkexec" for a reason. I have a vague understanding that this pkexec business has something to do with PolicyKit, but I don't really know what PolicyKit is or how to tell if something is broken with it. Thanks.

  Read the article

• Is it possible to disable the retry mechanism in Exim

  - by Tony Meyer

  I have a very simple Exim configuration that's just forwarding all mail to a set of destination addresses. When immediate delivery to an address fails, the message is added to the queue (and then processed by the retry rules). I want to change this so that if immediately delivery fails, the message is :blackhole:d. (It's ok if a bounce is generated instead, as I'll just redirect the bounce to the :blackhole:). This needs to occur for temporary failures (i.e. 4xx) as well as permanent (i.e. 5xx) ones. I understand that this means that if delivery can't be done immediately the message will be permanently and irretrievably lost. In this particular context, that isn't a problem. Reading over this, it sounds suspiciously like "how can I improve my spamming Exim server". That really isn't what this is for, and if you can figure out a way I can prove that, I'm happy to do so!

  Read the article

• Ubuntu 12.04 LTS loops the login screen unless you login as Guest

  - by Mário Silva

  I am running a VMWare Player with a Ubuntu 12.04 LTS Precise Pangloin as Guest on my Windows 7. Sometimes I get the shutdown blue screen error in Windows, this time it happened when I was running the Player. When I restarted everything Ubuntu gave the not so unfamiliar in this forum Login Loop in adminstrator login. I login and there's this black screen where I can only read: "piix4...smbus:0.0.0.07.3 Host Smbus controller not enabled" . When I go to the Prompt in root mode it fails to update and only upgraded, specially some plugins ( I think graphic plugins) which also appear in one an error message after quitting the prompt, but they´are successfully installed. They are not the error message. After that I have been working with the Fail/safe Mode recovery panel. When I try to update via Root I get errors like this: W:failed to fetch http://extras.ubuntu.com/ubuntu/dists/precise/release.gpg could not resolve 'extras/ubuntu.com There are 8 more like this referring to areas like: -archive/canonical.com -ppa.Launchpad.net -security.Ubuntu.com -Us.archive.ubuntu.com - release.gpg precise-updates/release.gpg precise_backport/release.gpg Final Message: some index files failed to download.....they have been ignored or old files are used. The black screens most of the time pass by too fast for me to pick up any information. But in general I think I have done everything I was able to in the recovery panel including updating network and graphic packages and recovering filesystem packages and the basic stuff ( I am a beginner regarding Linux ) in the root prompt. Now I am stuck in this screen with graphic options: - Run in low-graphics mode just for one session - Reconfigure Graphics - Troubleshoot the error - Exit to console login I am trying to choose to reconfigure graphics but the mouse disappears in the virtual machine screen and sometimes when options change ity´s only the first and last option. ut this happens from the blue without messages. This particular option menu is in the regular GUI style against a black screen in Terminal style. Really strange. Thanx in advance, all is welcome and appreciated.

  Read the article

• Encrypting a non-linux partition with LUKS.

  - by linuxn00b

  I have a non-Linux partition I want to encrypt with LUKS. The goal is to be able to store it by itself on a device without Linux and access it from the device when needed with an Ubuntu Live CD. I know LUKS can't encrypt partitions in place, so I created another, unformatted partition of the EXACT same size (using GParted's "Round to MiB" option) and ran this command: sudo cryptsetup luksFormat /dev/xxx Where xxx is the partition's device name. Then I typed in my new passphrase and confirmed it. Oddly, the command exited immediately after, so I guess it doesn't encrypt the entire partition right away? Anyway, then I ran this command: sudo cryptsetup luksOpen /dev/xxx xxx Then I tried copying the contents of the existing partition (call it yyy) to the encrypted one like this: sudo dd if=/dev/yyy of=/dev/mapper/xxx bs=1MB and it ran for a while, but exited with this: dd: writing `/dev/mapper/xxx': No space left on device just before writing the last MB. I take this to mean the contents of yyy was truncated when it was copied to xxx, because I have dd'd it before, and whenever I have dd'd to a partition of the exact same size, I never get that error. (and fdisk reports they are the same size in blocks). After a little Googling I discovered all luksFormat'ted partitions have a custom header followed by the encrypted contents. So it appears I need to create a partition exactly the size of the old one + however many bytes a LUKS header is. What size should the destination partition be, no. 1, and no. 2, am I even on the right track here? UPDATE I found this in the LUKS FAQ: I think this is overly complicated. Is there an alternative? Yes, you can use plain dm-crypt. It does not allow multiple passphrases, but on the plus side, it has zero on disk description and if you overwrite some part of a plain dm-crypt partition, exactly the overwritten parts are lost (rounded up to sector borders). So perhaps I shouldn't be using LUKS at all?

  Read the article

• Running 'sudo' over SSH

  - by Wesho

  I'm writing a script which is to log onto a bunch of remote machines and run a command on them. I've set up keys so the user running the script does not have to type the password of each machine, but only type in the passphrase in the beginning of the script. The problem is that the command on the remote machines requires sudo to run. And at the same time the whole point of the script is to rid the user of having to type in passwords multiple times. Is there way to avoid typing in the password for sudo? Changing permissions of the command on the remote machines is not an option.

  Read the article

• rsync problems and security concerns

  - by MB.

  Hi I am attempting to use rsync to copy files between two linux servers. both on 10.04.4 I have set up the ssh and a script running under a cron job. this is the message i get back from the cron job. To: mark@ubuntu Subject: Cron ~/rsync.sh Content-Type: text/plain; charset=ANSI_X3.4-1968 X-Cron-Env: X-Cron-Env: X-Cron-Env: X-Cron-Env: Message-Id: <20120708183802.E0D54FC2C0@ubuntu Date: Sun, 8 Jul 2012 14:38:01 -0400 (EDT) rsync: link_stat "/home/mark/#342#200#223rsh=ssh" failed: No such file or directory (2) rsync: opendir "/Library/WebServer/Documents/.cache" failed: Permission denied (13) rsync: recv_generator: mkdir "/Library/Library" failed: Permission denied (13) * Skipping any contents from this failed directory * rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1060) [sender=3.0.7] Q.1 can anyone tell me why I get this message -- rsync: link_stat "/home/mark/#342#200#223rsh=ssh" failed: No such file or directory (2) the script is: #!/bin/bash SOURCEPATH='/Library' DESTPATH='/Library' DESTHOST='192.168.1.15' DESTUSER='mark' LOGFILE='rsync.log' echo $'\n\n' >> $LOGFILE rsync -av –rsh=ssh $SOURCEPATH $DESTUSER@$DESTHOST:$DESTPATH 2>&1 >> $LOGFILE echo “Completed at: `/bin/date`” >> $LOGFILE Q2. I know I have several problems with the permissions all of the files I am copying usually require me to use sudo to manipulate them. My question is then is there a way i can run this job without giving my user root access or using root in the login ?? Thanks for the help .

  Read the article

• Where is the Flash in Chrome?

  - by Daniel

  I installed Google Chrome. This is the first thing I did after installing Ubuntu. I went into firefox, and went to chrome.google.com, and hit the button. I don't like package managers, and avoid the command line like the pox. Then, I started using Google Chrome. I went to Kongregate, and clicked on a game. It told me I didn't have flash. A few different websites told me the same. I assumed that they must have been wrong. I hit the link to Adobe, to install Flash, and it reassured me; of course, Google Chrome includes Flash. I checked my version - Chrome 5.0.375.126. Of course, I just downloaded it. I scoured the internet for solutions. None worked. Many seemed to involve re-enabling Flash, or something like that. But insofar as I can tell, there is no Flash anywhere in my Chrome. I feel like I bought a Reese's cup, and found solid chocolate. I checked in the Chrome plugin manager, and everything. A few solutions told me to copy some garbage into my command line and hit enter (as almost all solutions to problems on linux entail). I did it, reluctantly, and it did nothing. I thought Flash was supposed to come with Chrome. But it didn't. Sooooo... What gives? Google Chrome version: Google Chrome 5.0.375.126 (Official Build 53802) WebKit 533.4 V8 2.1.10.15 User Agent Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.126 Safari/533.4 Command Line /opt/google/chrome/google-chrome Operating System: Ubuntu 10.4 64 bit.

  Read the article

• Implementing dry-run in bash scripts

  - by Apikot

  How would one implement a dry-run option in a bash script? I can think of either wrapping every single command in an if and echoing out the command instead of running it if the script is running with dry-run. Another way would be to define a function and then passing each command call through that function. Something like: function _run () { if [[ "$DRY_RUN" ]]; then echo $@ else $@ fi } _run mv /tmp/file /tmp/file2 DRY_RUN=true _run mv /tmp/file /tmp/file2 Is this just wrong and there is a much better way of doing it?

  Read the article

• Troubleshoot broken ZFS

  - by BBK

  I have one zpool called tank in RaidZ1 with 5x1TB SATA HDDs. I'm using Ubuntu Server 11.10 Oneric, kernel 3.0.0-15-server. Installed ZFS from ppa also I'm using zfs-auto-snapshot. The ZFS file system when zfs module loaded to the kernel hangs my computer. Before it I created few new file systems: zfs create -V 10G tank/iscsi1 zfs create -V 10G tank/iscsi2 zfs create -V 10G tank/iscsi3 I shared them through iSCSI by /dev/tank/iscsiX path. And my computer started to hanging sometimes when I used tank/iscsiX by iSCSI, do not know why exactly. I switched off iSCSI and started to remove this file systems: zfs destroy tank/iscsi3 I'm also using zfs-auto-snapshot so I had snapshots and without -r key my command not destroying the FS. So I issued next command: zfs destroy tank/iscsi3 -r The tank/iscsi3 FS was clean and contain nothing - it was destroyed without an issue. But tank/iscsi2 and tank/iscsi1 contained a lot of information. I tried zfs destroy tank/iscsi2 -r After some time my computer hang out. I rebooted computer. It didn't boot very fast, HDDs starts working like a crazy making a lot of noise, after 15 minutes HDDs stopped go crazy and OS booted at last. All seems to be ok - tank/iscsi2 was destroyed. After file systems at the tank was accessible, zpool status showed no corruption. I issued new command: zfs destroy tank/iscsi1 -r Situation was repeated - after some time my computer hang out. But this time ZFS seams not to healed itself. After computer switched on it started to work: loading scripts and kernel modules, after zfs starting to work it hanging my computer. I need to recover else ZFS file systems which lying in the same zpool. Few month ago I backup OS to flash drive. Booting from backed-up OS and import have the same results - OS starts hanging. How to recover my data at ZFS tank?

  Read the article

• Reliable alert dialogs from the shell

  - by intuited

  I'd like to have a message pop up in response to various system events, mostly in order to be able to set reminders for myself from a shell session. There are a few ways to do this; zenity seems to be the most polished. However, I've found at least two problems with zenity: Messages do not appear on all workspaces. I tried using the gtk option --screen to control this, but they just appear on the current workspace regardless. So if I am switching workspaces as the message comes up, I will not see it. Messages do not appear above all other windows. Specifically, if I am using guake, a new zenity message will appear below the guake window and I won't be able to see it. I tried a few other apps a while back. Both gmessage and xmessage exhibited problem 1; gmessage also exhibited problem 2. I did find that kalarm, which can be scripted from the command line, worked acceptably, but I'm trying to avoid running the KDE stack if possible, and would prefer something lightweight with zenity's versatility. It seems that it might be possible to arrange for these problems to be resolved by setting the WM_CLASS, but I'm in a bit over my head there. It might also be possible to make modifications to the window after it launches with a script, but again I'm not sure where to look for resources on that.

  Read the article

< Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >