Search Results

Search found 10698 results on 428 pages for 'inline functions'.

Page 321/428 | < Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >

• NetBackup prefers "Scratch" tapes over dedicated tapes

  - by wfaulk

  I have a NetBackup 6.0MP7 installation running on Windows Server 2003. It functions as the only Master Server and Media Server. I swap a full set of tapes in and out every week, but leave a set of tapes with their Volume Pool set to "Scratch" in all the time. The weekly tape sets then get rotated back in after a period of time. Largely, this works fine. I seldom actually need the scratch tapes, but every once in a while, a backup will run over what I have dedicated to the task. However, one week's set of tapes consistently gets declined in favor of the scratch pool. The backup policies are the same for every week, they all have "Policy Volume Pool" set to "NetBackup", and all of the tapes for every week (beside the scratch tapes) have had their pools assigned as "NetBackup", definitely including the week that always gets ignored. That said, it doesn't ignore all of the NetBackup pool tapes for that week. It does usually write to two or three of them, but it writes to like 20 of the scratch tapes. (I haven't thought to look to see if it's always the same two or three tapes.) And this problem never seems to occur for any other week. It doesn't load the tapes and then reject them; it never seems to try to use them at all. They are not flagged as frozen. They are all active and unassigned when I swap them in. The tapes are in a Quantum PX510 tape library. The NetBackup server is attached to the library/robot via fibrechannel going through an HP-branded Brocade switch. I'm not an expert on NetBackup at all. I don't really even know where to look. Any advice on logs to look at or logging to enable or really anything at all would be appreciated. I'll keep an eye on the question and update it if anyone needs any more info to help.

  Read the article

• Ubuntu 10.04 Server on Hyper-V Server R2 has sluggish install and command line

  - by Paul Hobart

  I've installed Ubuntu Server 10.04 (64 bit) on a Hyper-V Server R2. I've encountered two issues that I think are related: Very slow install Very slow command prompt The text-mode installer goes through a series of text-based prompt windows. It takes 7-10 seconds for each of these windows to draw on the screen. The end result is that every time I answer a prompt and hit enter I wait for 15 seconds while the screen redraws line by line. I can literally see each line of text being drawn (like the old 300 baud modems days). Once done installing, scrolling on the command line is super slow. For instance, if a simple command, like "ls", causes the screen to scroll, it will scroll very slowly. This happens on a fresh install. The server functions as a LAMP server and an OpenSSH server, but that's it (I don't even have any Virtual Hosts set up yet). AND this only happens on the Virtual Machine console. I access the console through Hyper-V Manager and don't have this problem on any of my other Virtual Machines. Also, this problem does NOT happen when accessing a shell through OpenSSH. How can I improve this performance issue?

  Read the article

• Good PC-based video conference control tools?

  - by Jeremy Wadhams

  I'm looking to improve the user experience in our video conference rooms, by simplifying the things users do all the time (setting up a call, muting and unmuting, panning and zooming between a few room-appropriate presets) and totally taking away the functions that we don't use or that are more likely to ruin the experience (changing the brightness of the TV, using the VNC presenter mode). The rooms each have Tandberg Edge or MXP video units, I'm not looking at PC-based solutions like Skype or iChat. The classic way to do this would be to plunk down huge money for an AMX or Crestron panel. This does have some advantages, and I am considering that approach, but in my initial investigation, that looks expensive, inflexible, and proprietary. On the other hand, the Tandberg video units I'm looking to control are very thorough XML API (PDF), so some of the integration magic that Crestron and AMX consider to be a value add, I could reproduce at mashup speeds. Anyone aware of an Open Source or Commercial product that takes advantage of the readily available web APIs, some simple touch screen PCs, and builds a product that is more like skinning an AJAX web app, and ideally more cost effective than the proprietary panels?

  Read the article

• Getting a TTY in a Connectback Shell

  - by Asad R.

  I'm often asked by friends to help with small Linux problems, and more often than not I'm required to login to the remote system. Usually there are a lot of issues with making an account and logging in (sometimes the box is behind a NAT device, sometimes SSHD isn't installed, etc.) so I usually just ask them to make a connect-back shell using netcat (nc -e /bin/bash ). If they don't have netcat I can just ask them to grab a copy of a statically compiled binary which isn't that hard or time consuming to download and run. Though this works well enough for me to enter simple commands, I can't run any apps that require a tty (vi, for example) and can't use any job control functions. I managed to bypass this issue by running in.telnetd with a few arguments within the connect-back shell that would assign me a terminal and drop me to a shell. Unfortunately in.telnetd isn't usually installed by default on most systems. What's the easiest way to get a fully functional connect-back terminal shell without requiring any non-standard packages? (A small C program that does the job would be fine as well, I just can't seem to find much documentation on how a TTY is assigned/allocated. A solution that doesn't require me to plough through the source code for SSHD and TELNETD would be nice :))

  Read the article

• Linux: Force fsck of a read-only mounted filesystem?

  - by Timothy Miller

  I'm developing for a headless embedded appliance, running CentOS 6.2. The user can connect a keyboard, but not a monitor, and a serial console would require opening the case, something we don't want the user to have to do. This all pretty much obviates the possibility of using a recovery USB drive to boot from, unless all it does is blindly reimage the harddrive. I would like to provide some recovery facilities, and I have written a tool that comes up on /dev/tty1 in place of getty to provide these functions. One such function is fsck. I have found out how to remount the root and other file systems read-only. Now that they are read-only, it should be safe to fsck them and then reboot. Unfortunately, fsck complains to me that the filesystems are mounted and refuses to do anything. How can I force fsck to run on a read-only mounted partition? Based on my research, this is going to have to be something obscure. "-f" just means to force repair of a clean (but unmounted) partition. I need to repair a clean or unclean mounted partition. From what I read, this is something "only experts" should do, but no one has bothered to explain how the experts do it. I'm hoping someone can reveal this to me. BTW, I've noticed that e2fsck 1.42.4 on Gentoo will let you fsck a mounted partition, even mounted read-write, but it seems only to do so if fsck is run from a terminal, so it can ask the user if they're sure they want to do something so dangerous. I'm not sure if the CentOS version does the same thing, but it appears that fsck CAN repair a mounted partition, but it flatly refuses to when not run from a terminal. One last-resort option is for me to compile my own hacked fsck. But I'm afraid I'll mess it up in some unexpected way. Thanks! Note: Originally posted here.

  Read the article

• Keyboard's media keys are blocked by a program

  - by Mike Hanson

  I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

  Read the article

• Exchange 2010 Mail Enabled Public Folder Unable to Recieve External (anon) e-mail.

  - by Alex

  Hello All, I am having issues with my "Public Folders" mail enabled folders receiving e-mails from external senders. The folder is setup with three Accepted Domains (names changed for privacy reasons): 1 - domain1.com (primary & Authoritative) 2 - domain2.com (Authoritative) 3 - domain3.com (Authoritative) When someone attempts to send an e-mail to [email protected] from inside the organization, the e-mail is received and placed in the appropriate folder. However, when someone tries to send an e-mail from outside the organization (such as a gmail account), the following error message is received: "Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 Recipient address rejected: User unknown (state 14)." When I try to send an e-mail to the same folder, using the same e-mail address above ([email protected]), but with domain2.com instead of domain3.com, it works as intended (both internal & external). I have checked, double checked, and triple checked my DNS settings comparing those from domain2 & domain3 with them both appearing identical. I have tried recreating the folders in question with the same results. I have also ran Get-PublicFolderClientPermission "\Web Programs\folder" with the following results for user anonymous: RunspaceId : 5ff99653-a8c3-4619-8eeb-abc723dc908b Identity : \Web Programs\folder User : Anonymous AccessRights : {CreateItems} Domain2.com & Domain3.com are duplicates of each other, but only domain2.com works as intended. All other exchange functions are functioning properly. If anyone out there has any suggestions, I would love to hear them. I've just hit a brick wall. Thanks for all your help in advance! --Alex

  Read the article

• Ruby 1.9.3 - Bundler - Graylog2

  - by Arenstar

  im having a strange problem with bundler. Using ruby 1.8 the following works fine however not with 1.9 it always results in Could not find rake-0.9.2.2 in any of the sources Run `bundle install` to install missing gems. i dont understand why, but it functions correctly with rvm. I can not however use rvm, this is not a solution to my problem Install Ruby cd /usr/local/src wget http://ftp.ruby-lang.org/pub/ruby/1.9/ruby-1.9.3-p194.tar.gz tar xzf ruby-1.9.3-p194.tar.gz && cd ruby-1.9.3-p194 ./configure --prefix=/opt/lp/ruby-1.9.3-test make all && make install Install Graylog cd /usr/local/src wget https://github.com/downloads/Graylog2/graylog2-web-interface/graylog2-web-interface-0.9.6p1.tar.gz tar xzf graylog2-web-interface-0.9.6p1.tar.gz cd graylog2-web-interface-0.9.6p1 Setup Graylog cd /usr/local/src/graylog2-web-interface-0.9.6p1 sed -i "3 i gem 'thin', '~> 1.3.1'" Gemfile /opt/lp/ruby-1.9.3-test/bin/gem install bundle /opt/lp/ruby-1.9.3-test/bin/bundle install --path vendor/bundle --binstubs Begin the Test cd /usr/local/src/graylog2-web-interface-0.9.6p1 /opt/lp/ruby-1.9.3/bin/bundle exec bin/rake #Could not find rake-0.9.2.2 in any of the sources #Run `bundle install` to install missing gems. cd /usr/local/src/graylog2-web-interface-0.9.6p1 /opt/lp/ruby-1.9.3/bin/bundle exec bin/thin -e production -S test.sock -c . -R config.ru start #Could not find rake-0.9.2.2 in any of the sources #Run `bundle install` to install missing gems. Where am i going wrong?

  Read the article

• POST Fail via AJAX Request?

  - by Jascha

  I can't for the life of me figure out why this is happening. This is kind of a repost (submitted to stackoverflow, but maybe a server issue?). I am running a javascript log out function called logOut() that has make a jQuery ajax call to a php script... function logOut(){ var data = new Object; data.log_out = true; $.ajax({ type: 'POST', url: 'http://www.mydomain.com/functions.php', data: data, success: function() { alert('done'); } }); } the php function it calls is here: if(isset($_POST['log_out'])){ $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('logOutSuccess')"; $connection->runQuery($query); // <-- my own database class... // omitted code that clears session etc... die(); } Now, 18 hours out of the day this works, but for some reason, every once in a while, the POST data will not trigger my query. (this will last about an hour or so). I figured out the post data is not being set by adding this at the end of my script... $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('POST FAIL')"; $connection->runQuery($query); So, now I know for certain my log out function is being skipped because in my database is the following data: if it were NOT being skipped, my data would show up like this: I know it is being skipped for two reasons, one the die() at the end of my first function, and two, if it were a success a "logOutSuccess" would be registered in the table. Any thoughts? One friend says it's a janky hosting company (hostgator.com). I personally like them because they are cheap and I'm a fan of cpanel. But, if that's the case??? Thanks in advance. -J

  Read the article

• how do i write an init script for django-supervisor

  - by amateur

  pardon me as this is my first time attempting to write a init script for centos 5. I am using django + supervisor to manage my celery workers, scheduler. Now, this is my naive simple attempt /etc/init.d/supervisor #!/bin/sh # # /etc/rc.d/init.d/supervisord # # Supervisor is a client/server system that # allows its users to monitor and control a # number of processes on UNIX-like operating # systems. # # chkconfig: - 64 36 # description: Supervisor Server # processname: supervisord # Source init functions /home/foo/virtualenv/property_env/bin/python /home/foo/bar/manage.py supervisor --daemonize inside my supervisor.conf: [program:celerybeat] command=/home/property/virtualenv/property_env/bin/python manage.py celerybeat --loglevel=INFO --logfile=/home/property/property_buyer/logfiles/celerybeat.log [program:celeryd] command=/home/foo/virtualenv/property_env/bin/python manage.py celeryd --loglevel=DEBUG --logfile=/home/foo/bar/logfiles/celeryd.log --concurrency=1 -E [program:celerycam] command=/home/foo/virtualenv/property_env/bin/python manage.py celerycam I couldn't get it to work. 2013-08-06 00:21:03,108 INFO exited: celerybeat (exit status 2; not expected) 2013-08-06 00:21:06,114 INFO spawned: 'celeryd' with pid 11772 2013-08-06 00:21:06,116 INFO spawned: 'celerycam' with pid 11773 2013-08-06 00:21:06,119 INFO spawned: 'celerybeat' with pid 11774 2013-08-06 00:21:06,146 INFO exited: celerycam (exit status 2; not expected) 2013-08-06 00:21:06,147 INFO gave up: celerycam entered FATAL state, too many start retries too quickly 2013-08-06 00:21:06,147 INFO exited: celeryd (exit status 2; not expected) 2013-08-06 00:21:06,152 INFO gave up: celeryd entered FATAL state, too many start retries too quickly 2013-08-06 00:21:06,152 INFO exited: celerybeat (exit status 2; not expected) 2013-08-06 00:21:07,153 INFO gave up: celerybeat entered FATAL state, too many start retries too quickly I believe it is the init script, but please help me understand what is wrong.

  Read the article

• Moodle serves on IP only - will not work with mod_proxy

  - by Jon H

  I'm trying to set a moodle server up on an Ubuntu box, which already serves Plone & Trac via Apache. In my Moodle config I have $CFG-wwwroot = 'http://www.server-name.org/moodle' The configuration below works fine for the first two, but when I visit www.server-name.com/moodle I get: Incorrect access detected, this server may be accessed only through "http://xxx.xxx.xxx.xxx:8888/moodle" address, sorry It then forwards to the IP address, where Moodle functions fine. What am I missing to get the server name approach working correctly? Apache Config follows: LoadModule transform_module /usr/lib/apache2/modules/mod_transform.so Listen 8080 Listen 8888 Include /etc/phpmyadmin/apache.conf <VirtualHost xxx.xxx.xxx.xxx:8080> <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On <Location /> ProxyPass http://127.0.0.1:8082/ ProxyPassReverse http://127.0.0.1:8082/ </Location> </VirtualHost> <VirtualHost xxx.xxx.xxx.xxx:80> ServerName www.server-name.org ServerAlias server-name.org ProxyRequests Off FilterDeclare MyStyle RESOURCE FilterProvider MyStyle XSLT resp=Content-Type $text/html TransformOptions +ApacheFS +HTML TransformCache /theme.xsl /home/web/webapps/plone/theme.xsl TransformSet /theme.xsl FilterChain MyStyle ProxyPass /issue-tracker ! ProxyPass /moodle ! <Location /issue-tracker/login> AuthType Basic AuthName "Trac" AuthUserFile /home/web/webapps/plone/parts/trac/trac.htpasswd Require valid-user </Location> Alias /moodle /usr/share/moodle/ <Directory /usr/share/moodle/> Options +FollowSymLinks AllowOverride None order allow,deny allow from all <IfModule mod_dir.c> DirectoryIndex index.php </IfModule> </Directory> </VirtualHost>

  Read the article

• Connecting to IPv6 hosts when mobile and on a Surface?

  - by Cerebrate

  Specifically, at my usual location, I have an IPv6 network which connects to the Internet via a static tunnel set up to Hurricane Electric's tunnel broker ( http://www.tunnelbroker.net/ ). This works essentially perfectly, allowing inbound and outbound connectivity. Now, however, I need to connect back to host(s) on that network over IPv6 from mobile tablet(s); meaning the conditions are such that there is no guarantee or even likelihood of native IPv6 support where it happens to be at any given time, and the IPv4 address of the tablet will change on a fairly regular basis. The native Teredo support, as configured by default, functions well enough to let me ping my target hosts, but appears to have neither the reliability nor the throughput to support anything else; I have been unable to make any actual connections (trying a number of TCP-based protocols) using it. I had considered setting up an independent tunnel for the tablet(s), and using scripts to update the client endpoint IP address when it changes, but since both (a) many of the locations will be behind NAT devices over which I have no control, and (b) the option over which I do have control is an AT&T Unite hotspot which does not offer protocol 41 forwarding or respond to ICMP on its public address, this approach does not seem viable. I am additionally constrained as the mobile tablet(s) in question are Surface RTs, and as such are incapable of running, for example, AICCU client software. What is my best option to pursue to obtain IPv6 connectivity in this scenario?

  Read the article

• Error in Bind9 named.conf file. Bind won't start.

  - by tj111

  I'm trying to setup a DNS server on an Ubuntu Server machine (10.04). I configured an entry in named.conf.local to test it, but when trying to restart bind9 I get the following error: * Starting domain name service... bind9 [fail] So I checked the output of syslog and this is what I get. May 20 18:11:13 empression-server1 named[4700]: starting BIND 9.7.0-P1 -u bind May 20 18:11:13 empression-server1 named[4700]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' May 20 18:11:13 empression-server1 named[4700]: adjusted limit on open files from 1024 to 1048576 May 20 18:11:13 empression-server1 named[4700]: found 4 CPUs, using 4 worker threads May 20 18:11:13 empression-server1 named[4700]: using up to 4096 sockets May 20 18:11:13 empression-server1 named[4700]: loading configuration from '/etc/bind/named.conf' May 20 18:11:13 empression-server1 named[4700]: /etc/bind/named.conf:10: missing ';' before 'include' May 20 18:11:13 empression-server1 named[4700]: loading configuration: failure May 20 18:11:13 empression-server1 named[4700]: exiting (due to fatal error) So it thinks I have an error in the default named.conf file, which is pretty ridiculous. I went through it and deleted a blank line just for the hell of it, but I can't see how it figures there's an error in there. Note that before this I did have an error in named.conf.local, but it showed up properly in syslog and I fixed it, so it is reporting the correct file. Here is the contents of named.conf: // This is the primary configuration file for the BIND DNS server named. // // Please read /usr/share/doc/bind9/README.Debian.gz for information on the // structure of BIND configuration files in Debian, *BEFORE* you customize // this configuration file. // // If you are just adding zones, please do that in /etc/bind/named.conf.local include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones";

  Read the article

• Find and Replace several several different values all at once

  - by matt

  I have a file with multiple instances of Text_1 and Text1 and I need to replace both those strings with Text_A and TextB respectively. Currently I'm doing two Find and Replace functions on each file one that finds Text_1 and replaces it with Text_A and the other that finds Text1 and replaces it with TextB. Is there any way to do this all at once instead of having to run "Find and Replace" twice? I am using Dreamweaver CS3, but I also have Notepad++, regular Notepad, OO Writer, MS Word if those will be easier. Ideally I could do this in Dreamweaver or Notepad++ but I'm open to downloading something else to get the job done. I'd prefer not to have to do any command line stuff or create a batch file (while I'm aware of it, I don't understand it really). Edit: In case the above description isn't clear, let me explain it this way... I want to run Find & Replace 1 time in 1 document and I want it to do ALL of the following during that one Find & Replace instance: Find: Text_1 and Replace with: Text_A Find: Text1 and Replace with: TextB I am not trying to do a Find and Replace across several documents.

  Read the article

• get ubuntu terminal to send an escape sequence (control+shift+up)

  - by user62046

  This problem starts when I use emacs ( with -nw option). Let me first explain it. I tried to define hotkey (for emacs) as following (global-set-key [(control shift up)] 'other-window) but it doesn't work (no error, just doesn't work), neither does (global-set-key [(control shift down)] 'other-window) But (global-set-key [(control shift right)] 'other-window) and (global-set-key [(control shift left)] 'other-window) work! But because the last two key combinations are used by emacs (as default), I don't wanna change them for other functions. So how could I make control-shift-up and control-shift-down work? I have googled "(control shift up)", it seems that control-shift-up is used by other people, (but not very few results). In the Stack Overflow forum, Gille answered me as following: Ctrl+Shift+Up does send a signal to your computer, but your terminal emulator is apparently not transmitting any escape sequence for it. So your problem is in two parts. First you must get your terminal emulator to send an escape sequence, which depends on your terminal emulator, and is Super User material, or Unix.SE if you're using a unix system. Then you need to declare the escape sequence in Emacs, and my answer explains that part So I come here for this question: How do I get my terminal (I use ubuntu 10.04, and the built-in terminal) to send an escape sequence for Control+Shift+Up Control+Shift+down

  Read the article

• VNC server failed to start CentOS

  - by Shaun

  I followed a tutorial on how to install and get VNCserver to run on CentOS 6 (since freenx isnt supported yet) and I keep getting Starting VNC server: 1:user [FAILED] How do I figure out whats going on here? Im new to Linux/CentOS and im trying to get RDP going so I can step away from SSH as much as possible (you know us Windows users love our pretty GUI's). So, where is the error log at and how do I find it? Or maybe someone else has experienced this and knows the solution based on the simple error given? After running in debug mode, here is my error + . /etc/init.d/functions ++ TEXTDOMAIN=initscripts ++ umask 022 ++ PATH=/sbin:/usr/sbin:/bin:/usr/bin ++ export PATH ++ '[' -z '' ']' ++ COLUMNS=80 ++ '[' -z '' ']' +++ /sbin/consoletype ++ CONSOLETYPE=pty ++ '[' -f /etc/sysconfig/i18n -a -z '' -a -z '' ']' ++ . /etc/profile.d/lang.sh ++ unset LANGSH_SOURCED ++ '[' -z '' ']' ++ '[' -f /etc/sysconfig/init ']' ++ . /etc/sysconfig/init +++ BOOTUP=color +++ RES_COL=60 +++ MOVE_TO_COL='echo -en \033[60G' +++ SETCOLOR_SUCCESS='echo -en \033[0;32m' +++ SETCOLOR_FAILURE='echo -en \033[0;31m' +++ SETCOLOR_WARNING='echo -en \033[0;33m' +++ SETCOLOR_NORMAL='echo -en \033[0;39m' +++ PROMPT=yes +++ AUTOSWAP=no +++ ACTIVE_CONSOLES='/dev/tty[1-6]' +++ SINGLE=/sbin/sushell ++ '[' pty = serial ']' ++ __sed_discard_ignored_files='/\(~\|\.bak\|\.orig\|\.rpmnew\|\.rpmorig\|\.rpmsave\)$/d' + '[' -r /etc/sysconfig/vncservers ']' + . /etc/sysconfig/vncservers ++ VNCSERVERS='1:larry 2:moe 3:curly' ++ VNCSERVERARGS[1]='-geometry 800x600' ++ VNCSERVERARGS[2]='-geometry 640x480' ++ VNCSERVERARGS[3]='-geometry 640x480' + prog='VNC server' + RETVAL=0 + case "$1" in + start + '[' 0 '!=' 0 ']' + . /etc/sysconfig/network ++ NETWORKING=yes ++ HOSTNAME=vps.binaryvisionaries.com ++ DOMAINNAME=server.name ++ GATEWAYDEV=venet0 ++ NETWORKING_IPV6=yes ++ IPV6_DEFAULTDEV=venet0 + '[' yes = no ']' + '[' -x /usr/bin/vncserver ']' + '[' -x /usr/bin/Xvnc ']' + echo -n 'Starting VNC server: ' Starting VNC server: + RETVAL=0 + '[' '!' -d /tmp/.X11-unix ']' + for display in '${VNCSERVERS}' + SERVS=1 + echo -n '1:larry ' 1:larry + DISP=1 + USER=larry + VNCUSERARGS='-geometry 800x600' + runuser -l larry -c 'cd ~larry && [ -r .vnc/passwd ] && vncserver :1 -geometry 800x600' + RETVAL=1 + '[' 1 -eq 0 ']' + break + '[' -z 1 ']' + '[' 1 -eq 0 ']' + failure 'vncserver start' + local rc=1 + '[' color '!=' verbose -a -z '' ']' + echo_failure + '[' color = color ']' + echo -en '\033[60G' + echo -n '[' [+ '[' color = color ']' + echo -en '\033[0;31m' + echo -n FAILED FAILED+ '[' color = color ']' + echo -en '\033[0;39m' + echo -n ']' ]+ echo -ne '\r' + return 1 + '[' -x /usr/bin/plymouth ']' + /usr/bin/plymouth --details + return 1 + echo + '[' 1 -eq 98 ']' + return 1 + exit 1

  Read the article

• Winamp question: Generating 'dynamic playlists' from file playlists -OR- mass-tagging by file playli

  - by Daddy Warbox

  I'm trying to think of a way to do this. I sort my songs into a variety of playlists corresponding to different 'moods' I might have as I listen to them, and some songs fit for more than one kind of mood (e.g. a jazz song might be 'stylish' and 'emotional', or something to that effect). I also give them star ratings for a general sort of opinion about them. I want to be able to filter and sort my media library by the moods I want or don't want, as well as by star rating. Anyone have a good way to do something like this? I can't seem to use Winamp's dynamic playlists to generate lists from existing filesystem playlists (e.g. songs in a given .m3u files). Hand-tagging files with Winamp's tag editor is a royal pain. It's trouble enough just giving a star rating and sorting into playlists as is. If there is there a way to mass tag songs within each playlist with mood words to allow me to create dynamic playlists, I'd be fine (for now). It'd be nice if I could do this via some kind of hotkey for each song, too. I'm looking to see if I can use a macro program or something to do that, though. Thanks in advance. P.S: Alternatively, would something like Foobar have functions like this? Note: Italics are recent edits.

  Read the article

• How to backup iTunes on Windows to folder/share, i.e. without "Back Up to Disc"? No DVD writer avail

  - by Chris W. Rea

  (Surprised I didn't already find an answer here to this!) I've got a computer on which I'd like to back up the iTunes library – music, movies, apps, everything. We're talking multiple gigabytes. Unfortunately, it seems that iTunes' own built-in "Back Up to Disc" feature (the only backup feature I can find in iTunes) only functions with a CD or DVD writer/burner. The computer in question does not have a DVD burner. While it has a CD burner, attempting to back up to CDs would require dozens of discs plus more time than I'm willing to spend swapping them. So: What is the recommended way to back up an entire iTunes library on a Windows computer, to a non-CD/DVD location such as an external hard drive or a network shared folder? Then, once such a backup has been performed, what is the process for restoring the library – e.g. after the computer has been repaved with a new version of Windows – so that iTunes is resurrected whole and recognizes devices it syncs with? Thank you!

  Read the article

• Can one really fry a monitor by setting the wrong HorizSync and VertRefresh?

  - by rumtscho

  I've encountered this problem on several different systems with several different monitors: a monitor functions perfectly under Windows. I install a Linux and the max resolution is at some impossibly low value, mostly 640x480, changing it in Xorg.conf doesn't work. The X.org log file then shows that the driver cannot determine the correct refresh rate for the monitor, so it ignores everything in Xorg.conf and just loads in some default minimalistic mode. Googling the problem leads to an easy solution: set the HorizSync and VertRefresh in Xorg.conf, and everything works. The problem seems to be a common one, and I've seen dozens of results recommending the solution. Each of them contains the warning that you should use the value ranges provided with the monitor. Because if you don't, and your video card sends a signal with the wrong refresh rate, this can damage your monitor. Of course, you don't have a user manual for your monitor any more. If you are lucky to find one on the attic or on the net, it doesn't contain any information about the supported refresh rate. So you just type in the value suggested in the solution description, which varies wildly depending on your source, and cross your fingers. You restart, and... ... you've set the wrong values. So the monitor shows a short message like "input signal out of range", and you do a hard restart, repair your Xorg.conf in recovery mode, and everything is fine, including your monitor. So does this warning reflect a real possibility, or is it just a geeky urban legend? Or is it something which used to happen in the past, before manufacturers started protecting the monitors against it? Is it technically possible with every monitor technology, or is it maybe something which can only happen to a CRT? If you think that it's true, why? Have you ever witnessed a monitor die from the wrong refresh config, or have you read of it in a reputable source?

  Read the article

• An easily customizable linux distribution using minimal disk space?

  - by Frank

  I'm looking for a linux distribution that can be easily used to create my own distribution that's the same system with some software installed. So basically I should be able to create an iso which, when installed, will have the linux distribution with my desired installed. More specifically, I plan on installing mysql and a bit of my own software which shouldn't be too big. However, this distribution needs to be extremely small in terms of disk space. The distribution, including mysql should not exceed 100mb. It should, of course still be able to connect to the internet and perform other standard functions. I don't need X/any sort of window manager, and would prefer not to have it since it would increase disk usage. Currently I have tried ttylinux and tiny core linux. I've found that ttylinux, while is extremely small, has almost nothing so that mysql can't even be installed. Tiny core linux, on the other hand is a bit too big. I've found openembedded and linux from scratch, but I would prefer for the install and build process to be much easier. What other distribution would you recommend for my purposes? Minimizing disk usage is the most important, followed by ease of installing and creating the custom distribution.

  Read the article

• The bottlenecks of any computer, what to look for?

  - by WebDevHobo

  Whether it is a laptop or a desktop, any computer is made up of several pieces of hardware that communicate with each other. Sending data back and forth to ensure that the user gets the desired results. I have seen some theoretical stuff on computers & hardware, but I wonder how it all comes together. CPU RAM Graphics Card L1 CACHE L2 CACHE L3 CACHE FSB ... And all other things. Which is the biggest bottle neck? Why would a person not want/need a big value in one of those categories in certain situations? P.S.: when reading the specs of the i5 750 processor, I came across this description: In place of the FSB, one or more high speed, point-to-point buses called Quick Path Interconnect (QPI) are used, formerly known as Common Serial Interconnect Bus or CSI. QPI features higher bandwidth than the traditional FSB and is better suited to system scaling. What is this, and how does it compare to FSB? EDIT: I am not planning to buy a computer at all. The goal of this question is to understand the internal relation of various hardware pieces, their specific functions and how they work together. For instance, I have heard to a somewhat higher-than-usual amount of L2/L3 Cache can help speed up your computer. What's up with saying that? Also I forgot to mention Hard-disk RPM.

  Read the article

• Kernel Logging disabled?

  - by Tiffany Walker

  uname -a Linux host 2.6.32-279.9.1.el6.i686 #1 SMP Tue Sep 25 20:26:47 UTC 2012 i686 i686 i386 GNU/Linux And start ups: ls /etc/init.d/ abrt-ccpp certmonger dovecot irqbalance matahari-broker mdmonitor nfs proftpd rpcbind single ypbind abrtd cgconfig functions kdump matahari-host messagebus nfslock psacct rpcgssd smartd abrt-oops cgred haldaemon killall matahari-network mysqld ntpd qpidd rpcidmapd sshd acpid cpuspeed halt ktune matahari-rpc named ntpdate quota_nld rpcsvcgssd sssd atd crond httpd lfd ma tahari-service netconsole oddjobd rdisc rsyslog sysstat auditd csf ip6tables lvm2-lvmetad matahari-sysconfig netfs portreserve restorecond sandbox tuned autofs cups iptables lvm2-monitor matahari-sysconfig-console network postfix rngd saslauthd udev-post But when I installed CSF/LFD I am getting nothing. LFD does not create lfd.log and nor are any blocks being logged in /var/log/messages either from the firewall. This is not natural. I looked for klogd but maybe I am looking in the wrong place for it to see if it is enabled? ls /etc/init.d/syslog ls: cannot access /etc/init.d/syslog: No such file or directory Also noticed no syslog? Also noticed this: csf -d 84.113.21.201 Adding 84.113.21.201 to csf.deny and iptables DROP... iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. I've never seen this before and this is a dedicated box. Also: ./csftest.pl Testing ip_tables/iptable_filter...OK Testing ipt_LOG...OK Testing ipt_multiport/xt_multiport...OK Testing ipt_REJECT...OK Testing ipt_state/xt_state...OK Testing ipt_limit/xt_limit...OK Testing ipt_recent...OK Testing xt_connlimit...OK Testing ipt_owner/xt_owner...OK Testing iptable_nat/ipt_REDIRECT...OK Testing iptable_nat/ipt_DNAT...OK RESULT: csf should function on this server iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Error when starting qpidd as a service

  - by Sparks

  I have recently swapped from CENTOS 5 to FEDORA 17. Previously I have created my own init.d scripts successfully (albeit not for qpidd) however, in FEDORA I cannot get it to work. I have created the following script (called qpidd) in the init.d directory: #!/bin/bash # # /etc/rc.d/init.d/qpidd # # QPID/AMQP Broker scripts # # # chkconfig: 2345 20 80 # description: QPID/AMQP Broker service # processname: qpidd # pidfile: /var/lock/subsys/qpidd # Source function library. . /etc/init.d/functions SERVICENAME=qpidd start() { echo -n "Starting $SERVICENAME: " daemon qpidd -d & retval=$? touch /var/lock/subsys/$SERVICENAME return $retval } stop() { echo -n "Shutting down $SERVICENAME: " qpidd -q & retval=$? rm -f /var/lock/subsys/$SERVICENAME return $retval } case "$1" in start) start ;; stop) stop ;; status) status qpidd ;; restart) stop start ;; condrestart) [ -f /var/lock/subsys/<service> ] && restart || : ;; *) echo "Usage: $SERVICENAME {start|stop|status|restart" exit 1 ;; esac exit $? After this, I ran chkconfig --add qpidd, however, now when I run sudo service qpidd start I get the following message: Starting qpidd (via systemctl): Job failed. See system journal and 'systemctl status' for details. If I then run systemctl status qpidd I get the following message: Failed to issue method call: Unit name qpidd is not valid. I am now lost, I have search the web and Stack Overflow but cannot find anybody with similar problem, any help or direction to a website that can help would be much appreciated Sparks :)

  Read the article

• Restore passwd for root on a server

  - by s.mihai

  Hello,       I have a DVR server with linux embeded. It has some telnet functions but i don't have the password for it (the chinese manufacturer refuses to give me the password). I did get a upgrade folder from them and found a passwd file inside.       So i assume that when i upgrade the firmware the password in that file will be used.       Now i am trying to modify the file so taht i can insert a password i already know.       The problem is that i don't know how to create the password hash from what i figured the password hash is $1$1/lfbDKX$Hmd.FqzB8IZEohPesYi961       The file is named rom.ko and i found a command telnetd /mnt/yaffs/web/boa -c /mnt/yaffs/web & /bin/cp -f /mnt/yaffs/rom.ko /etc/shadow in a script file so i assume this is the right way.       Can you help me reconstruct a password that i know already? Tell me how or make one for me :) ?... passwd file: root:$1$1/lfbDKX$Hmd.FqzB8IZEohPesYi961:0:0:99999:7:-1:-1:33637592 bin::10897:0:99999:7::: daemon::10897:0:99999:7::: adm::10897:0:99999:7::: lp::10897:0:99999:7::: sync::10897:0:99999:7::: shutdown::10897:0:99999:7::: halt::10897:0:99999:7::: mail::10897:0:99999:7::: news::10897:0:99999:7::: uucp::10897:0:99999:7::: operator::10897:0:99999:7::: games::10897:0:99999:7::: gopher::10897:0:99999:7::: ftp::10897:0:99999:7::: nobody::10897:0:99999:7::: next::11702:0:99999:7:::

  Read the article

• Can't install MailParse on cpanel server

  - by Tom

  Hi, I've got a linux vps running CentOs 5.5 (cpanel/whm), I've installed MailParse via Module Installers section on whm, and it did install it, the end of setup log: running: make INSTALL_ROOT="/root/tmp/pear-build-root/install-mailparse-2.1.5" install Installing shared extensions: /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions/no-debug-non-zts-20090626/ running: find "/root/tmp/pear-build-root/install-mailparse-2.1.5" | xargs ls -dils 508718 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5 508745 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr 508746 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib 508747 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php 508748 4 drwxr-xr-x 3 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions 508749 4 drwxr-xr-x 2 root root 4096 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions/no-debug-non-zts-20090626 508744 196 -rwxr-xr-x 1 root root 193502 Feb 6 21:08 /root/tmp/pear-build-root/install-mailparse-2.1.5/usr/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so Build process completed successfully Installing '/usr/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so' install ok: channel://pecl.php.net/mailparse-2.1.5 Extension mailparse enabled in php.ini The mailparse.so object is not in /usr/local/lib/php/extensions/no-debug-non-zts-20090626 Now, when i try to use mailparse functions using php i get the following error: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/local/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so' - /usr/local/lib/php/extensions/no-debug-non-zts-20090626/mailparse.so: cannot open shared object file: No such file or directory in Unknown on line 0 What should i do?

  Read the article

< Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >