Search Results

Search found 9128 results on 366 pages for 'big theta'.

Page 323/366 | < Previous Page | 319 320 321 322 323 324 325 326 327 328 329 330  | Next Page >

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• Active Directory Corrupted In Windows Small Business Server 2011 - Server No Longer Domain Controller

  - by ThinkerIV

  I have a rather bad problem with my Windows SBS 2011. First of all, I'll give the background to what caused the problem. I was setting up a new small business server network. I had my job about finished. The server was working great, all the workstations had joined the domain, and I had all my applications and data moved to the server. I thought I was done. But then it happened. I tried adding one more computer to the domain, and to my dismay the computer name was set to the same name as the server. Apparently when a computer joins a domain with the same name as another machine that is already on the domain, it overrides the first one. For normal workstations, this is not a big deal, you just delete the computer from AD and rejoin the original computer to the domain. However, for a server that is the domain controller it is a whole different story. Since the server got overridden in AD, it is no longer the domain controller. The DNS service is not working and all kinds of other services are failing also. So the question is, what are my options? I am embarrassed to admit it, but since this is a new server one thing I did not have setup yet was backup. So I have no backups to work from. I am worried that things are broken enough that I might need to do a reinstall. However, I already have several days worth of configuration into this server, so I would obviously prefer if there was a fix that would prevent me from needing to do a reinstall. All the server components are there and installed correctly, but they are misconfigured (I think it is basically just Active Directory). So I have the feeling that if I did the right thing I could solve the issue without a reinstall. Is there anyway to rerun the component that installs the initial configuration to "convert" the base windows server 2008 r2 install into a SBS? In other words in the program files folder there is an application called SBSsetup.exe, is there anyway to rerun this and have it reconfigure AD, etc. to work with SBS? Any insight will be greatly appreciated. Thanks.

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• Looking for app to work fluidly with CSV data in graph form

  - by Aszurom

  It often occurs to me that if I had a good tool for viewing CSV data in graphical format, and comparing two sets of numbers to each other, I could do a great deal of meaningful trend watching and data interpretation. For example, perfmon can output quite a lot of data about a server into a CSV file, but there's no good way to view it. A lot of scripts could/have been written that would populate CSV files. I could write these all day long. My problem is that I need a great viewer. I've seen quite a few things that will take a CSV file and after a lot of tweaking and user adjustment produce a static gif/png image. A static image doesn't do me a lot of good, because I have to look at it, then re-calibrate the parameters of the program, regenerate the image, repeat. That sucks. I could do this in Excel. Ideally, I would want a FLUID graph viewer. On the fly, I can adjust how much of my timeline I'm viewing. I could adjust the scaling so that one big spike doesn't make 99.9% of the data an unreadable line across the bottom of the X axis. Stuff like that. I should be able to say "show me CSV column 3 and column 5 as graphs. Show me the data scaled for 20 or 150 entries, and let me slide that window up and down the column of data. Auto scale to fit 95% of data within the Y axis and let crazy spikes go off the screen." Maybe I'm terribly spoiled by how you can drag, zoom, and slide data around on my iPad. I want to be able to view a spreadsheet of data with that fluidity and not have to guess at what sort of static snapshot I want to create from it. I don't want to have to make a study of how to tweak some data plotting program to let me import my file and do what I could just do in Excel. I want to scale, zoom, and transform my graph on the fly and then export a snapshot of it once I have it the way I want it. Is there anything out there that fills this need? I'll take linux, osx, win32 or even iOS suggestions.

  Read the article

• Plesk Postfix Mail Server 9.5.4 very heavy load, 1000s of processes

  - by Eugene van der Merwe

  Our Plesk Linux Ubuntu 64-bit mail server has extremely high load and we don't know how to isolate it. The load was okay will two weeks ago but in the last two weeks it's seriously deteriorated. The mail server has been running for years and we have had sporadic performance issues. Normally we reduce the load by turning off all SPAM checks until the problem is sorted (which sometimes resolves itself). Currently we have turned of real time block lists, SPF checking and we have attempted to turn off SpamAssassin. No matter what we do the SpamAssassin check box stays ticked in the GUI. Out of desperation we have done /etc/init.d/psa-spamassassin stop. For years we haven't been able to do SpamAssassin because it kills the server. We would like to use it but performance is more important for now. We cannot turn off Greylisting. The moment we turn off Greylisting our help desk is inandated with calls. Out of desperation we investigated truncating the Greylisting database which is now 2.5 GB big but we abandoned this after noticing turning of Greylisting doesn't improve the performance at all. We have no anti-virus. It's just more load and Dr. Web never really worked that well for us. But we'll try that if it will make a difference. We have implemented Postfix Anvil. This seems to have made the situation worse so we disabled it. We’re not sure if this is the case. Our current mail server is configured to forward all SMTP to a relay server. We did so to reduce the load. This helped a lot because outgoing queues are generally empty. We are running in an Expand configuration. The mail server has about 12 000 accounts of which maybe half are active. We have read through this document: http://www.postfix.org/STRESS_README.html but there are too many settings and we don’t know which ones to choose. Please assist urgently. We need advice on how to fix this problem before all our clients abandon is. The only clue we have is that there are 100s of these processes: 30 13205 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13207 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13208 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13209 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13213 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue

  Read the article

• Radeon HD4850 serious issues when using DirectX 10

  - by ricsmania

  Hello, I have a problem with my video card. Whenever I run a DirectX 10 game, it works for a few seconds (10 or so) and then starts displaying nothing but big polygons. I have tested this with Crysis and Resident Evil 5, both have the same problems. The same games running under DirectX 9 work fine, except for some small black squares once in a while. I have the following specs: Asus P7P55D LE Intel Core i5 750 Sapphire Radeon HD4850 1GB 2x2GB Patriot Viper II Sector 5, DDR3 1600 MHz OCZ Stealth X Stream 500SXS 500W At first I thought it could be the video card overheating (it has stock cooling), but the game crashes even when it's running at 50 degrees C, and it's never been higher than 70. I also thought it could be the PSU, but as far as I know 500W is enough for this computer, especially because I haven't overclocked anything. My OS is Windows 7 X64 and I am using Catalyst 10.10, but I have also tried many older versions with no success. I don't think there is a problem with the card itself, or else it wouldn't run DirectX 9 games I believe. I have spent many hours searching for a solution but I couldn't, so any help is appreciated. Thank you. EDIT: I did some further investigation about the problem, and it seems taspeotis was right, it might be related to memory. I slightly underclocked the memory from 993 to 965 MHz and the problem went away completely. Both the black squares using DirectX 9 and the weird polygons using DirectX 10. I was using RE DirectX 10 Benchmark, as it consistently crashed around the same point, and now I can play the full benchmark with no artifacts at all. Unfortunately, the underclock has an obvious hit in performance. Although it's not critical, it's definitely noticeable. So, if the video memory test software showed no erros, but the card needs an underclock to work, what might be the problem? Temperature? Voltage? By the way, I couldn't find what the default voltage for this card is. And what is a good software to try and increase it? I tried Ati Tray Tools but it has a bug that increases the clock speed dramatically whenever I change something in the Overclock tab, so I'm afraid it might fry my card. Worst case scenario, if I don't find I solution I will try to slightly increase the GPU clock to compensate for the memory clock. Thank you again.

  Read the article

• What are incentives (if any) to use WinRT instead of .Net?

  - by Ark-kun

  Let's compare WinRT with .Net .Net .Net is the 13+ years evolution of COM. Three main parts of .Net are execution environment, standard libraries and supported languages. CLR is the native-code execution environment based on COM .Net Framework has a big set of standard libraries (implemented using managed and native code) that can be used from all .Net languages. There are .Net classes that allow using OS APIs. WPF or Silverlight provide a XAML-based UI framework .Net can be used with C++, C#, Javascript, Python, Ruby, VB, LISP, Scheme and many other languages. C++/.Net is a variation of the C++ language that allows interaction with .Net objects. .Net supports inheritance, generics, operator and method overloading and many other features. .Net allows creating apps that run on Windows (XP, 7, 8 Pro (Desktop and Metro), RT, CE, etc), Mac OS, Linux (+ other *nix); iOS, Android, Windows Phone (7, 8); Internet Explorer, Chrome, Firefox; XBox 360, Playstation Suite; raw microprocessors. There is support for creating games (2D/3D) using any managed language or C++. Created by Developer Division WinRT WinRT is based on COM. Three main parts of WinRT are execution environment, standard libraries and supported languages. WinRT has a native-code execution environment based on COM WinRT has a set of standard libraries that more or less can be used from WinRT languages. There are WinRT classes that allow using OS APIs. Unnamed Silverlight clone provides a XAML-based UI framework WinRT can be used with C++, C#, Javascript, VB. C++/CX is a variation of the C++ language that allows interaction with WinRT objects. Custom WinRT components don't support inheritance (classes must be sealed), generics, operator overloading and many other features. WinRT allows creating apps that run on Windows 8 Pro and RT (Metro only); Windows Phone 8 (limited). There is support for creating games (2D/3D) using C++ only. Ordered by Windows Team I think that all the aspects except the last ones are very important for developers. On the other hand it seems that the most important aspect for Microsoft is the last one. So, given the above comparison of conceptually identical technologies, what are incentives (if any) to use WinRT instead of .Net?

  Read the article

• SQL Clustering on Hyper V - is a cluster within a cluster a benefit.

  - by Chris W

  This is a re-hash of a question I asked a while back - after a consultant has come in firing ideas in to other teams in the department the whole issue has been raised again hence I'm looking for more detailed answers. We're intending to set-up a multi-instance SQL Cluster across a number of physical blades which will run a variety of different systems across each SQL instance. In general use there will be one virtual SQL instance running on each VM host. Again, in general operation each VM host will run on a dedicated underlying blade. The set-up should give us lots of flexibility for maintenance of any individual VM or underlying blade with all the SQL instances able to fail over as required. My original plan had been to do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Within the VMs - create a failover cluster and then install SQL Server clustering. The consultant has suggested that we instead do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Create a cluster on the HOST machines which will host all the VMs. Within the VMs - create a failover cluster and then install SQL Server clustering. The big difference is the addition of step 4 whereby we cluster all of the guest VMs as well. The argument is that it improves maintenance further since we have no ties at all between the SQL cluster and physical hardware. We can in theory live migrate the guest VMs around the hosts without affecting the SQL cluster at all so we for routine maintenance physical blades we move the SQL cluster around without interruption and without needing to failover. It sounds like a nice idea but I've not come across anything on the internet where people say they've done this and it works OK. Can I actually do the live migrations of the guests without the SQL Cluster hosted within them getting upset? Does anyone have any experience of this set up, good or bad? Are there some pros and cons that I've not considered? I appreciate that mirroring is also a valuable option to consider - in this case we're favouring clustering since it will do the whole of each instance and we have a good number of databases. Some DBs are for lumbering 3rd party systems that may not even work kindly with mirroring (and my understanding of clustering is that fail overs are completely transparent to the clients). Thanks.

  Read the article

• How to set up a file server in a restricted corporate environment

  - by Emilio M Bumachar

  I work in a big corporation, and the disk space my team gets in the corporate file server is so low, I am considering turning my work PC into a file server. I ask this community for links to tutorials, software suggestions, and advice in general about how to set it up. My machine is an Intel Core2Duo E7500 @ 3GHz, 3 GB of RAM, Running Windows XP Service Pack 3. Upgrading, formatting or installing another OS is out of the question. But I do have Administrator priviledges on the PC, and I can install programs (at least for now). A lot of security software I don't even know about is and must remain installed. But I only need communication whithin the corporate network, which is not restricted. People have usernames (logins) on the corporate network, and I need to use them to restrict access. Simply put, I have a list of logins of team members, and only people in the list should access the files. I have about 150 GB of free disk space. I'm thinking of allocating 100 GB to the team's shared files. I plan monthly backups on machines of co-workers, same configuration. But automation of backups is a nice, unnecessary feature: it's totally acceptable for me to manually copy the contents to a different machine once a month. Uptime is important, as everyone would use these files in their daily work. I have experience as a python and C programmer, but no experience whatsoever as a sysadmin, and almost nothing of my programming experience is network programming. I'm a complete beginner in this. Thanks in advance for any help. EDIT I honestly appreciate all the warnings, I really do, but what I plan to make available is mostly stuff that now is solely on DVDs just for space reasons. It's 'daily work' to read them, but 'daily work write' files will remain on the corporate server. As for the importance of uptime, I think I overstated it: a few outages are OK, it's already an improvement over getting the DVDs. As for policy, my manager is kind of on my side, I will confirm that before making my move. As for getting more space through the proper channels, well, that was Plan A, and it's still on the table... But I don't have much hope. I'm not as "core businees" as I'd like.

  Read the article

• Change Logon DPI setting in Windows 8.1

  - by jmc302005

  I love how M$ keeps making decisions for me about how I want my desktop to look. Now they have added per-user dpi settings. The problem this has created is that there is no adjustable dpi setting for the Lock/Logon screen. Let me explain. you can change the dpi setting to be the same across all displays and this does affect the icons and font on the lock/logon screen. However it does not affect any app/program that can run on the lock/logon screen. Ex. I use a 44" flat screen tv for my monitor on my desktop. Big enough for me to sit in my recliner and use my comp. But I don't have a wireless keyboard. And it sucks having the wire from the keyboard running across the floor. Plus I really don't want to keep a keyboard next to me. So I use the on screen keyboard for logging in and quick typing (search, web address, etc.) So the problem is that with the new dpi setup my on screen keyboard takes up nearly half the screen. Does M$ think we are all blind? Oh no I remember they think desktops should look like tablets and phones. I tried looking through the registry to see if I could find a setting for it. In the key HKEY_USERS.DEFAULT\Control Panel\Desktop there is a string value named "LogicalDPIOverride" with a value of -1. I have a feeling this is where I can fix the issue. I tried changing the value to 0 and to 1 with no change in the result. Instead I noticed that after logging out and back in the -1 value was back in the registry. So now M$ has also added a way for us to not be able to change a setting in the registry. They are making it harder and harder for us power users to be able to do anything with the settings in windows. Soon we will all have the same exact Windows with absolutely no customization. ok sorry for the quick rant. The real question here is. How can I change this defualt dpi crap? Can I use the LogPixels string that worked for dpi in Windows 7? Here are 2 Screen shots 1 of the Lock Screen and 1 of the Logon Screen http://i.imgur.com/6RM5ufE.jpg http://i.imgur.com/cnY5bmm.jpg Please any help will be appreciated.

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Secure, efficient, version-preserving, filename-hiding backup implemented in this way?

  - by barrycarter

  I tried writing a "perfect" backup program (below), but ran into problems (also below). Is there an efficient/working version of this?: Assumptions: you're backing up from 'local', which you own and has limited disk space to 'remote', which has infinite disk space and belongs to someone else, so you need encryption. Network bandwidth is finite. 'local' keeps a db of backed-up files w/ this data for each file: filename, including full path file's last modified time (mtime) sha1sum of file's unencrypted contents sha1sum of file's encrypted contents Given a list of files to backup (some perhaps already backed up), the program runs 'find' and gets the full path/mtime for each file (this is fairly efficient; conversely, computing the sha1sum of each file would NOT be efficient) The program discards files whose filename and mtime are in 'local' db. The program now computes the sha1sum of the (unencrypted contents of each remaining file. If the sha1sum matches one in 'local' db, we create a special entry in 'local' db that points this file/mtime to the file/mtime of the existing entry. Effectively, we're saying "we have a backup of this file's contents, but under another filename, so no need to back it up again". For each remaining file, we encrypt the file, take the sha1sum of the encrypted file's contents, rsync the file to its sha1sum. Example: if the file's encrypted sha1sum was da39a3ee5e6b4b0d3255bfef95601890afd80709, we'd rsync it to /some/path/da/39/a3/da39a3ee5e6b4b0d3255bfef95601890afd80709 on 'remote'. Once the step above succeeds, we add the file to the 'local' db. Note that we efficiently avoid computing sha1sums and encrypting unless absolutely necessary. Note: I don't specify encryption method: this would be user's choice. The problems: We must encrypt and backup 'local' db regularly. However, 'local' db grows quickly and rsync'ing encrypted files is inefficient, since a small change in 'local' db means a big change in the encrypted version of 'local' db. We create a file on 'remote' for each file on 'local', which is ugly and excessive. We query 'local' db frequently. Even w/ indexes, these queries are slow, since we're often making one query for each file. Would be nice to speed this up by batching queries or something. Probably other problems that I've now forgotten.

  Read the article

• System failure - need diagnostic recommendation

  - by Ladislav Mrnka

  I have big problem with my computer. Configuration is: Intel i7 + 6x2GB OCZ DDR3 Motheboard: Asus P6T Deluxe V2, HDD controller configured to AHCI Main drive: OCZ Vertex 2 (SSD) - contains all installed programs and system Second drive: Samsung SpinPoint - contains User profiles, ProgramData, virtual machines and databases Third drive: Samsung SpinPoint - data drive + backups OS: Windows 7 Ultimate x64 I have never had any problem with this computer until now. During weekend my computer completely crashed without any reason. Each time I tried to boot to Windows I got BSOD with message BAD_SYSTEM_CONFIG_INFO and automatic restart (I didn't install any new SW or HW). But after restart main OCZ drive was disconnected (not detected by BIOS). When I turned off and on computer, the drive was again connected. It also happend every single time I tried to repair installation somehow. It ended with some error and after restart drive was disconnected. The only thing which worked was format + fresh install. After installing almost everything I wanted to install Visual Studio 2010 Ultimate (complete installation without SQL Server Express). During installation of VS itself I always get BSOD - it is too fast so I'm not able to read description. After restart it searches for all disk drives for really long time and sometimes it changes boot drive so the system is not able to start - Bootmgr not found. After reconfiguring BIOS the system starts. There is no event describing the failure in Event viewer. Installing VS 2010 is absolutely necessary for me. I need help with diagnostic. I need to find where is the problem - I expect that the problem is in OCZ drive or in HDD controller on motherboard but I don't know how to find it. All components still have valid warranty. Can you recommend me some approach or tools to find the problem? Edit: I'm still looking for source of the problem. New information is that Windows are not able to perform check disk (Chkdsk) on the SSD system drive. After restarting it always starts checking drive and in part where files are checked it fails with BSOD - BAD_SYSTEM_CONFIG_INFO. After next restart and skipping check disk tests the system runs.

  Read the article

• HTTPS in sub domain redirects to main domain

  - by Amitabh

  We recently bought a wildcard certificate and installed it for a domain. It works fine for the main domain but seems to not work at all for any sub domains. Whats happening is we can access the sub domains fine on HTTP, but whenever we try HTTPS for the same sub domain url we are redirected back to the main domain. So if I put up a test folder "httpstest" in a sub domain with a index.html file in it, the following happens mysubdomain.mywebsite.com/httpstest/index.html or mysubdomain.mywebsite.com/httpstest/ works perfectly fine with http:// but mysubdomain.mywebsite.com/httpstest/ or mysubdomain.mywebsite.com/httpstest/index.html does not work with https:// and redirects to the main domain.Any help on this is greatly appreciated. The site is not the main site used for setting up the VPS. It was added from WHM. Environment: We are on a Linux VPS. Cpanel 11.30.6 , Apache 2.2.22, PHP 5.3.13 The Virtualhost entry looks like: <VirtualHost xx.xx.xxx.xx:443> ServerName my-own-website.com ServerAlias www.my-own-website.com DocumentRoot /home/amitabh/public_html ServerAdmin [email protected] UseCanonicalName Off CustomLog /usr/local/apache/domlogs/my-own-website.com combined CustomLog /usr/local/apache/domlogs/my-own-website.com-bytes_log "%{%s}t %I .\n%{%s}t %O ." ## User amitabh # Needed for Cpanel::ApacheConf <IfModule mod_suphp.c> suPHP_UserGroup amitabh amitabh </IfModule> <IfModule !mod_disable_suexec.c> SuexecUserGroup amitabh amitabh </IfModule> ScriptAlias /cgi-bin/ /home/amitabh/public_html/cgi-bin/ SSLEngine on SSLCertificateFile /etc/ssl/certs/my-own-website.com.crt SSLCertificateKeyFile /etc/ssl/private/my-own-website.com.key SSLCACertificateFile /etc/ssl/certs/my-own-website.com.cabundle CustomLog /usr/local/apache/domlogs/my-own-website.com-ssl_log combined SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown <Directory "/home/amitabh/public_html/cgi-bin"> SSLOptions +StdEnvVars </Directory> # To customize this VirtualHost use an include file at the following location # Include "/usr/local/apache/conf/userdata/ssl/2/amitabh/my-own-website.com/*.conf" </VirtualHost>` I guess I messed up the formatting big time. Any help on formatting and on the issue is great appreciated. Thank you. Update: I could not update the formatting here. I posted the same question in a linux forum . I will really appreciate any pointer on it.

  Read the article

• How do Windows 7 encrypted files look like?

  - by Sean Farrell

  Ok this is kind of an odd question: How do Windows 7 (Home Premium) encrypted files look like "from the outside"? Now here is the story. An acquaintance of a freind of mine got a nasty virus / scareware. So I wiped out my PC technician cap and went to work on it. What I did was remove the drive from the laptop and put drive into my external drive bay. I scanned the drive and yes it was loaded with stuff. That basically cured the infection and I could start the system back up. To check if it cured the problem I wanted to see the system while running. There where two user accounts, on with a password and one without (both admin users !?!). So I logged into the unprotected user and cleaned up the residual issues, like proxy server to localhost in the browser config. Now I wanted to do the same for the password protected user. What I noticed that from my system and the unprotected user account the files of the protected user looked garbled. The files are something like 12 random alphanum chars, but the folders looked ok. Naive as was thought this might be how encrypted files looked "from the outside". (I never use Microsoft's own security features, so how would I know. TrueCrypt is one big blob.) Since the second user could not be reached, I though sod it and removed the password from the account. (That might have been a mistake, I know.) Now I did the same clean up tasks and all nice and fine; except for the files which where still "encrypted". So I looked into many Windows Encrypted Files recovery posts and not all hope is lost, since I should be able to extract the certificate and with the password regain access to the files. Also note that windows did "only" prompt me that removing the password would be insecure, not that access to encrypted files would be lost, like it is claimed in most recovery articles. Resetting the password did not help and I gave up for the night. The question that nagged me half of the last night was, what if the files are not encrypted, but the scare-ware encrypted / destroyed the files? I don't want to spend hours of work trying to recover files that are not recoverable. The ting is that the user does not remember turning it on and aren't the files marked in blue and the filename is readable? Many thanks for input from users who have more knowledge about WEF...

  Read the article

• How to temporary disable a mirror video driver in windows xp registry

  - by happy clicker

  Because its a lot of text, I will ask first my question and then explain what the base problem is. Perhaps someone can give me a solution to the base problem: Is there is a way to temporary disable mirror video drivers (through registry or so), without uninstalling the corresponding software. I tested changing the enumeration in LocalMachine\Hardware\DeviceMap\Video but after reboot always the old configuration is restored. Explanation of the base problem We are working on a wpf-project for a department of a big company. There we have the problem that WPF renders only in software mode, although the hardware they have, must support hardware rendering (Tier 2). After searching for a solution to the problem, we found out that direct 3d does not work properly and we think thats why WPF can only use SW-rendering. In dxdiag.exe the direct3d-acceleration is enabled, but if we start the test-routine it always fails saying that it has not enough memory (it says memory, not video memory!). I have seen there 3 different types of pc’s (they have some hundreds of each type) and every type shows the exactly same behavior. We tried to update all the drivers, also dx (Version 9.0c) and we searched a lot in the web but could not find a solution. All the pcs have Intel Dual-Core processors or better, one type has an Intel gma 9000 graphics card the other two types have actual ATI and NVidia graphic-cards with 256MB onboard memory. Also the system memory is at least 2GB. Windows is XPSP3. The pc’s are of two different manufacturers. Because we see the exactly same behavior on every computer of this three very different computer-types, we don’t think that this is a driver or a direct x problem. What we’ve found in other newsgroups is, that direct x could be disturbed through mirror-video drivers such as NetMeeting, VNC and other remote desktop-installations. In the registry, we see under LocalMachine\Hardware\DeviceMap\Video a lot of such mirror-entries and we find also the definitions in the CurrentControlSet\Control\Video-Section (However this drivers are not shown in the hardware panel of the os). We can have admin-rights to one of these computers to test if disabling these drivers would help, but we must not change the configuration so that some software does not work after the tests. Therefore I cannot uninstall any software because I have not the mediums, licenses or knowhow to reinstall those apps. The support of this company however will only begin to work, if I can tell them what the real problem is. Thats why we search for a way to disable these mirror-drivers (or a hint to solve the dx problem if we are on a false trace)

  Read the article

• script to count the occurence of the particular string in the given time interval

  - by pruthvi

  We are trying to write a script "sendemail.sh" to count the number of occurrence of a particular string in a log file "SendEmail.log" within the given interval. We have a log file. In that we are searching for a pattern "ReqInputMsgLog" and need to count the number of times it occurred in the given period for eg: from "2014-08-19 11:30" to "2014-08-19 11:34". And our script look like this: #!/bin/sh enterdate=$1 echo $enterdate enddate=$2 enterdate1=`date +%s -d $enterdate +"%Y-%m-%d %H:%M"` echo $enterdate1 enddate1=`date +%s -d $enddate +"%Y-%m-%d %H:%M"` echo $enddate count=0 cat SendEmail.log | grep "ReqInputMsgLog" | awk -F "[" '{print $3}' | awk -F "," '{print $1}' > /con/scripts_server/file.txt for line in `cat /con/scripts_server/file.txt` do logdate=`echo $line | awk -F : '{print $1":"$2}'` if [[ $logdate < $enddate1 ]]; then count=`expr $count + 1` fi done echo $count But when we are trying to execute the script by the below command its not showing the proper count. ./sendemail.sh "2014-08-19 11:30" "2014-08-19 11:34" Log file is very big one. Small chunk has been posted here. INFO [SIBJMSRAThreadPool : 5] [2014-08-19 11:18:24,471] SendEmail - 8/19/14 11:18 AM,ECCF25B0-0147-4000-E000-1B830A3C05A9,ReqInputMsgLog,SendEmail,<?xml version="1.0" encoding="UTF-8"?> <in:sendEmailRequestMsg xmlns:in="http://EmailMed/EmailMedInterface" xmlns:ns0="wsdl.http://EmailMed/EmailMedInterface" xmlns:ns1="http://EmailMed/EmailMedInterface" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:me="wsdl.http://EmailMed/EmailMedInterface" xsi:type="me:sendEmailRequestMsg"> <in:sendEmail xmlns:xci0="http://EmailMed/EmailMedInterface"> INFO [SIBJMSRAThreadPool : 7] [2014-08-19 11:18:14,235] SendEmail - 8/19/14 11:18 AM,ECCEFDB2-0147-4000-E000-1B830A3C05A9,ReqInputMsgLog,SendEmail,<?xml version="1.0" encoding="UTF-8"?> <in:sendEmailRequestMsg xmlns:in="http://EmailMed/EmailMedInterface" xmlns:ns0="wsdl.http://EmailMed/EmailMedInterface" xmlns:ns1="http://EmailMed/EmailMedInterface" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:me="wsdl.http://EmailMed/EmailMedInterface" xsi:type="me:sendEmailRequestMsg"> <in:sendEmail xmlns:xci0="http://EmailMed/EmailMedInterface"> INFO [SIBJMSRAThreadPool : 7] [2014-08-19 11:18:14,241] SendEmail - xmlText: <?xml version="1.0" encoding="UTF-8"?> after awk command we will get a file "/con/scripts_server/file.txt" which looks similar like below: 2014-08-19 11:28:03 2014-08-19 11:28:06 2014-08-19 11:28:17 2014-08-19 11:28:53 2014-08-19 11:29:02 2014-08-19 11:29:47 2014-08-19 11:29:57 2014-08-19 11:30:07 2014-08-19 11:30:17 2014-08-19 11:30:19 2014-08-19 11:30:19 2014-08-19 11:30:22 2014-08-19 11:30:25 2014-08-19 11:30:25 2014-08-19 11:30:36 2014-08-19 11:30:51 2014-08-19 11:30:56 2014-08-19 11:30:59 2014-08-19 11:30:59 2014-08-19 11:31:08 2014-08-19 11:31:25 2014-08-19 11:32:19 2014-08-19 11:32:22 2014-08-19 11:32:27 2014-08-19 11:32:28 2014-08-19 11:32:41 2014-08-19 11:32:49 2014-08-19 11:32:59 2014-08-19 11:33:27 2014-08-19 11:33:41 2014-08-19 11:34:07 2014-08-19 11:34:14 2014-08-19 11:34:21 2014-08-19 11:34:25 2014-08-19 11:34:38 2014-08-19 11:34:50 2014-08-19 11:34:58

  Read the article

• How to disable or tune filesystem cache sharing for OpenVZ?

  - by gertvdijk

  For OpenVZ, an example of container-based virtualization, it seems that host and all guests are sharing the filesystem cache. This sounds paradoxical when talking about virtualization, but this is actually a feature of OpenVZ. It makes sense too. Because only one kernel is running, it's possible to benefit from sharing the same pages of filesystem cache in memory. And while it sounds beneficial, I think a set up here actually suffers in performance from it. Here's why I think why: my machines aren't actually sharing any files on disk so I can't benefit from this feature in OpenVZ. Several OpenVZ machines are running MySQL with MyISAM tables. MyISAM relies on the system's filesystem cache for caching of data files, unlike InnoDB's buffer pool. Also some virtual machines are known to do heavy and large I/O operations on the same filesystem in the host. For example, when running cat *.MYD > /dev/null on some large database in one machine, I saw the filesystem cache lowering in another, monitored by htop. This essentially flushes all the useful filesystem cache in guests (FIFO) and so it flushes the MySQL caches in the guests. Now users are complaining that MySQL is very slow. And it is. Some simple SELECT queries take several seconds on times disk I/O is heavily used by other machines. So, simply put: Is there a way to avoid filesystem cache being wiped out by other virtual machines in container-based virtualization? Some thoughts: Choosing algorithm for flushing filesystem cache in the kernel. (possible? how?) Reserving a certain amount of pages for a single VM. (seems no option for filesystem cache type of pages that reading man vzctl) Will running MySQL on another filesystem get me anywhere? If not, I think my alternatives are: Use KVM for MySQL-MyISAM running VMs. KVM actually assigns memory to the VM and does not allow swapping out caches unless using a balloon driver. Move to InnoDB and tune the buffer pools, dirty pages, etc. This is now considered to be 'nice to have' on the long-term as not everyone responsible for administration of the system understands InnoDB. more suggestions welcome. System software: Proxmox (now 1.9, could be upgraded to 2.x). One big LV assigned for the VMs.

  Read the article

• Is there a Distributed SAN/Storage System out there?

  - by Joel Coel

  Like many other places, we ask our users not to save files to their local machines. Instead, we encourage that they be put on a file server so that others (with appropriate permissions) can use them and that the files are backed up properly. The result of this is that most users have large hard drives that are sitting mainly empty. It's 2010 now. Surely there is a system out there that lets you turn that empty space into a virtual SAN or document library? What I envision is a client program that is pushed out to users' PCs that coordinates with a central server. The server looks to users just like a normal file server, but instead of keeping entire file contents it merely keeps a record of where those files can be found among various user PCs. It then coordinates with the right clients to serve up file requests. The client software would be able to respond to such requests directly, as well as be smart enough to cache recent files locally. For redundancy the server could make sure files are copied to multiple PCs, perhaps allowing you to define groups in different locations so that an instance of the entire repository lives in each group to protect against a disaster in one building taking down everything else. Obviously you wouldn't point your database server here, but for simpler things I see several advantages: Files can often be transferred from a nearer machine. Disk space grows automatically as your company does. Should ultimately be cheaper, as you don't need to keep a separate set of disks I can see a few downsides as well: Occasional degradation of user pc performance, if the machine has to serve or accept a large file transfer during a busy period. Writes have to be propogated around the network several times (though I suspect this isn't really much of a problem, as reading happens in most places more than writing) Still need a way to send a complete copy of the data offsite occasionally, and this would make it very hard to do differentials Think of this like a cloud storage system that lives entirely within your corporate LAN and makes use of your existing user equipment. Our old main file server is due for retirement in about 2 years, and I'm looking into replacing it with a small SAN. I'm thinking something like this would be a better fit. As a school, we have a couple computer labs I can leave running that would be perfect for adding a little extra redundancy to the system. Unfortunately, the closest thing I can find is Dienst, and it's just a paper that dates back to 1994. Am I just using the wrong buzzwords in my searches, or does this really not exist? If not, is there a big downside that I'm missing?

  Read the article

• Enterprise IPv6 Migration - End of proxypac ? Start of Point-to-Point ? +10K users

  - by Yohann

  Let's start with a diagram : We can see a "typical" IPv4 company network with : An Internet acces through a proxy An "Others companys" access through an dedicated proxy A direct access to local resources All computers have a proxy.pac file that indicates which proxy to use or whether to connect directly. Computers have access to just a local DNS (no name resolution for google.com for example.) By the way ... The company does not respect the RFC1918 internally and uses public addresses! (historical reason). The use of internet proxy explicitly makes it possible to not to have problem. What if we would migrate to IPv6? Step 1 : IPv6 internet access Internet access in IPv6 is easy. Indeed, just connect the proxy in Internet IPv4 and IPv6. There is nothing to do in internal network : Step 2 : IPv6 AND IPv4 in internal network And why not full IPv6 network directly? Because there is always the old servers that are not compatible IPv6 .. Option 1 : Same architecture as in IPv4 with a proxy pac This is probably the easiest solution. But is this the best? I think the transition to IPv6 is an opportunity not to bother with this proxy pac! Option 2 : New architecture with transparent proxy, whithout proxypac, recursive DNS Oh yes! In this new architecture, we have: Explicit Internet Proxy becomes a Transparent Internet Proxy Local DNS becomes a Normal Recursive DNS + authorative for local domains No proxypac Explicit Company Proxy becomes a Transparent Company Proxy Routing Internal Routers reditect IP of appx.ext.example.com to Company Proxy. The default gateway is the Transparent Internet proxy. Questions What do you think of this architecture IPv6? This architecture will reveal the IP addresses of our internal network but it is protected by firewalls. Is this a real big problem? Should we keep the explicit use of a proxy? -How would you make for this migration scenario? -And you, how do you do in your company? Thanks! Feel free to edit my post to make it better.

  Read the article

• MS DPM 2007: Testing the Recovery for a Production Domain

  - by NewToDPM

  Hi everybody! MS DPM 2007 is a new technology in my company, and so am I to the product. We have a classic Microsoft domain with two DCs, Exchange 2007 and a couple Web/MS SQL servers. I have deployed DPM one month ago on the domain, and after fixing the various issues I got with the replicas inconsistence and adapting the schedule and retention range to the server storage pool size, I can say the backup system is working correctly (no errors) as of today. However, there is one problem: we did not attempt to restore from the backups yet, which is a big no-no of course. I'm not sure about the way I should handle this, my main concern being Exchange and the System State of the DCs. From my understanding, DPM can only protect AND restore data on a server which is part of the same domain as the backup server. If I restore the System State (containing Active Directory) and the Exchange Storage Groups on a testing server, I am afraid it would completely disturb the domain functioning (for example, having two primary DCs on the domain). I am thinking about building a second DPM server on a testing separate domain which would mirror the replicas and then restore it on testing servers from this new domain. Is it the right way to handle the data recovery testing? How did you do on your domain when you first deployed DPM? I'd be grateful for any link/documentation or advice. Thank you in advance for your help! EDIT: Two options seem possible so far: i. Create another DC/Exchange server in the alternate location; ii. Create a separate domain in the alternate location and setup a trust between this domain and the production one. The option i is certainly the best but implies setting up a secondary Exchange server, with a dedicated public IP address so that if Exchange #1 dies, we can still send emails with Exchange #2. I don't know how complex this can be and would need to discuss it with my colleagues. The option ii would only fit the testing purposes. My only question regarding this is: if my production and DPM servers are part of domain A, and there is a trust between domains A and B, can I restore a domain A content to any domain B server?

  Read the article

• General guidelines / workflow to convert or transfer video "professionally"?

  - by cloneman

  I'm an IT "professional" who sometimes has to deal with small video conversion / video cutting projects, and I'd like to learn "the right way" to do this. Every time I search Google, there's always a disaster for weird, low-maturity trialware, or random forums threads from 3-4 years ago indicating various antiquated method to do it. The big question is the following: What are the "general" guidelines and tools to transcode video into some efficient (lossless?) intermediary, for editing purposes, for the purpose of eventually re-encoding it after? It seems to me like even the simplest of formats and tasks are a disaster of endless trial & error, or expertise only known by hardened experts who have a swiss army kife of weird conversion tools that they use, almost as if mounting an attack against the project. Here are a few cases in point: Simple VOB files extracted from DVD footage can't be imported into Adobe Premiere directly. Virtualdub is an old software people keep recommending but doesn't seem to support newer formats. I don't even know how to tell with certainty which codecs a video has, and weather the image is interlaced or not, and what resolution and codecs I'm dealing with. Problems: Choosing a wrong interlace option which diminishes quality Choosing a wrong pixel aspect ratio (stretches the image) Choosing a wrong "project type" in Premiere causing footage to require scaling Being forced to use some weird program that will have any number of negative effects What I'm looking for: Books or "Real knowledge" on format conversions, recognized tools, etc. that aren't some random forum guides on how to deal with video formats. Workflow guidelines on identifying a format going from one format to another without problems as mentioned above. Documentation on what programs like Adobe Premiere can and can't do with regards to formats, so that I don't use a wrench as a hammer. TL;DR How should you convert or "prepare" a video file to ensure it will be supported by Premiere for editing? Is premiere a suitable program to handle cropping, encoding, or should other tools be used for this, when making a video montage from a variety of source formats? What are some good books to read that specifically deal with converting videos that use any number of codecs?

  Read the article

• What DNS server to use for dynamic load-balancing of website?

  - by Marki555

  I will have 2 servers in different datacenters (different countries) and I want to use DNS load-balancing mainly for High Availability of website hosted on those 2 servers. It is just ad tracking site, which records hit in local database and returns few lines on html code. I want to return 2 A records each time because of DNS pinning in browsers (if one server fails, browser will try second A record which it has already cached). Both servers will be acting also as DNS servers for redundancy. Now comes my proposed solution: I will use BIND and have both servers as a master for that zone. On each server there will be running script, which will periodically test availability (http) of both servers and remove IP from DNS in case of failure. Now the questions :) 1) Is BIND suitable for this solution? I think BIND performance is good and it is easy to manipulate the zone file via script. And as I will modify the zone only in case of failure/maintenance, the modifications (and thus bind reload) won't be often. 2) I plan to use TTL of 5 minutes. The website will have about 1000-3000 req/s but from distinct clients (each IP only 1-3 requests), so I think the DNS load won't be too much. I suppose their ISPs will cache the responses for those 5 mins. Is there any reason to lower the TTL even more? 3) Is my master-master approach good? Or should I make one of the servers master and the other one slave? Right now each server can monitor both itself and the other one. If only webservice fails, both DNS nodes will notice it. If the whole server fails, then the remaining DNS node will notice it and the failed node will not answer DNS queries anyway. 4) Is it a big issue when one NS server does not respond to queries? If yes, I can make a third DNS, so anytime at least 2 of them would accept queries... 5) Should I rewrite the zone file via script, or just use dynamic DNS update (for example via nsupdateutility)?

  Read the article

• Detection of battery status totally messed up

  - by Faabiioo

  I already posted this question in the Ubuntu forum and stackOverflow. I forward it here with the hope to find some different opinions about the problem. I have an Acer TravelMate 5730, which is 3 y.o., running Ubuntu 10.04 LTS. One year ago I changed the battery because the old one died. Since then, everything worked like a charm. A week ago I was using my laptop running on battery; it was charged up to 60%. Suddenly it shut down and for about 24h it was like the battery was totally broken: it didn't charge anymore and the 'upower --dump' said state: critical. I was kind of resigned to buy a new battery, when suddenly the orange light became green: battery was charged and actually working; strangely the battery indicator was stuck to 100%, even after 2 hours running. I tried again with 'upower --dump' or 'acpi -b' commands and it kept saying battery is discharging, though maintaining the percentage to 100%. Thus, battery working fine up to 3 hours, without any warning when it was almost empty, likely to result in a brute shut down. Today something different. the 'upower --dump' command says: ... present: yes rechargeable: yes state: fully-charged energy: 0 Wh energy-empty: 0 Wh energy-full: 65.12 Wh energy-full-design: 65.12 Wh energy-rate: 0 W voltage: 14.481 V percentage: 0% capacity: 100% technology: lithium-ion I tried to boot WinXP and the problem is pretty much the same, with the battery fully-charged, percentage equal to 0% and no way to fix it. While writing, the situation has changed again: present: yes rechargeable: yes state: charging energy: 0 Wh energy-empty: 0 Wh energy-full: 65.12 Wh energy-full-design: 65.12 Wh energy-rate: 0 W voltage: 14.474 V percentage: 0% capacity: 100% technology: lithium-ion ...charging, but it does not charge up. (Recall, the battery lasted 3 hours until yesterday!). So, the big question is: is it an hardware issue, like a dedicated internal circuit is broken? or maybe it is just the battery that must be changed. Or, rather, some BIOS problem that could be fixed in some way. I'd appreciate every help that can shed some light on this annoying problem thanks

  Read the article

• How to auto advance a PowerPoint slide after an exit animation is over?

  - by joooc

  PowerPoint entrance animation set up with "Start: With Previous" starts right when a new slide is advanced. However, if you set up an exit animation in the same way, it doesn't start with a slide ending sequence. Instead, the "Start: On Click" trigger needs to be used and after your exit animation is over you still need one extra click just to advance to the next slide. Workarounds to this are obvious: create a duplicate slide, make your ending animations from the original slide being your starting animations on the duplicate slide and let them be followed with whatever you want or create a transition slide with those ending animations only and set up "Change Advance slide - Automatically after - [the time it takes your animations to finish]". These workarounds will make it work for your audience, visually. However, it has an impact on slide numbers you might need to adjust accordingly and/or duplicate content changes. If you are the only one creating and using your presentation, this might be just fine. But if you are creating a presentation in collaborative mode with three other people and don't even know who will be the presenter at the end, you can mess things up. Let's be specific: most of my slides have 0.2s fly in entrance animation applied to blocks of content coming from right, bottom or left. Advancing to the next slide I want them to fly out in another 0.2s exit animation being followed by new slide 0.2s fly in entrance animation of the new blocks. The swapping of the blocks should be triggered while advancing to the next slide, as usually. As mentioned, I'm not able to achieve this without one extra click between the slides. I wrote a VBA script that should start together with an exit animation and will auto advance a slide after 0.3s when the exit animation is over. That way I should get rid of those extra clicks which are needed right now. Sub nextslide() iTime = 0.3 Start = Timer While Timer < Start + iTime DoEvents Wend With SlideShowWindows(1).View .GotoSlide (ActivePresentation.SlideShowWindow.View.Slide.SlideIndex + 1) End With End Sub It works well when binded on a box, button or another object. But I can't make it run on a single click (anywhere on the slide) so that it could start together with the exit animation onclick trigger. Creating a big transparent rectangular shape over the whole slide and binding the macro on it doesn't help either. By clicking it you only get the macro running, exit animation is not triggered. Anyway, I don't want to bind the macro to any other workaround object but the slide itself. Anyone knows how to trigger a PowerPoint VBA script on slide onclick event? Anyone knows a secret setting that will make the exit animation work as expected i.e. animating right before exiting a slide while transitioning to the next one? Anyone knows how to beat this dragon? Thank you!

  Read the article

< Previous Page | 319 320 321 322 323 324 325 326 327 328 329 330  | Next Page >