Search Results

Search found 11466 results on 459 pages for 'geo ip'.

Page 323/459 | < Previous Page | 319 320 321 322 323 324 325 326 327 328 329 330  | Next Page >

  • MySQL port 3306 became filtered when configured with Keepalived on Ubuntu server 12.04 lts

    - by Ludwig
    I'm configuring two load balancer (lb01 & lb02) with keepalived for my two mysql server (db01 & db02) with standard port 3306. There is virtual ip address (192.168.205.10) to access it also act as failover, but somehow the web server in the front can't access this mysql server using vip. Here is my config: Keepalived: Only the mysql part that i added here. LB01: virtual_server 192.168.205.10 3306 { delay_loop 6 lb_algo rr lb_kind DR protocol TCP real_server 192.168.205.4 3306 { weight 10 TCP_CHECK { connect_port 3306 connect_timeout 2 } } } LB02: virtual_server 192.168.205.10 3306 { delay_loop 6 lb_algo rr lb_kind DR protocol TCP real_server 192.168.205.6 3306 { weight 10 TCP_CHECK { connect_port 3306 connect_timeout 2 } } } I already comment out the "bind-address=127.0.0.1" part in both server my.cnf. Also, remove all the firewall prog from my ubuntu server (ufw or iptables). Any help? thanks.

    Read the article

  • How to set RpcClientAccessServer for a Exchange 2010 mailbox database to a load balancer

    - by Archit Baweja
    I have 2 Exchange 2010 servers each with a Mailbox Database. I have also setup a Hardware Load Balancer (KEMP LoadMaster 2200 to be precise) to load balance the CAS role access. My HLB has an IP of 192.168.1.100. I've setup the DNS A record for mail.mydomain.com to point to 192.168.1.100. However when I try to set the RpcClientAccessServer on a mailbox database using Set-MailboxDatabase "My Mailbox Database" -RpcClientAccessServer mail.mydomain.com I get an error saying Exchange server "mail.mydomain.com" was not found. Please make sure you have typed it correctly. + CategoryInfo : NotSpecified: (:) [], ManagementObjectNotFoundException + FullyQualifiedErrorId : 4082394C Any ideas?

    Read the article

  • Listing the routing table takes long time to complete

    - by Rafal Rawicki
    When I print routes defined on my computer using route, it takes about 5 to 20 seconds to complete. Why does it take so much time? With VPN enabled: $ time sudo route Kernel IP routing table (...) real 0m21.423s user 0m0.000s sys 0m0.012s With no VPN, this is about 5 seconds - still, computer can do a lot in this time. I've repeated my measurements few times, getting very similar results each try. My machine is Ubuntu with 3.0.0 kernel, but as far as I know, route on the other computers works the same way.

    Read the article

  • Samsung i780 networking problem

    - by Infinity
    Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

    Read the article

  • Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

    - by SnAzBaZ
    I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

    Read the article

  • Exchange Server 2010 ActiveSync SSL Certificate Problem

    - by Cell-o
    Hi All, We have a problem related Exchange Server 2010 Activesync.My problem is;When I connecting to activesync from outside, I am receiving the following error. ExRCA is testing Exchange ActiveSync. The Exchange ActiveSync test failed. Test Steps Attempting to resolve the host name mail.xxxxx.com in DNS. The host name resolved successfully. Additional Details IP addresses returned: xx.0.x3.4 Testing TCP port 443 on host mail.x.com to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host name mail.x.com doesn't match any name found on the server certificate CN=xxxxxx. Thanks in advance all your help.

    Read the article

  • iptables -L lags on non localhost or anywhere address

    - by DazSlayer
    I am trying to configure iptables for ubuntu 10.04 and I have a problem with iptables -L lagging on rows where the destination or source address is not localhost or anywhere. The following entries will cause lag on their row: iptables -A INPUT -p tcp --dport 111 -s 192.168.1.14 -j ACCEPT iptables -A INPUT -p tcp --dport 90 -d 192.168.1.14 -j ACCEPT while this does not: iptables -A INPUT -p tcp --dport localhost -s 192.168.1.14 -j ACCEPT iptables -A INPUT -p tcp --dport localhost -d 192.168.1.14 -j ACCEPT I feel like this might be due to iptables checking to see if the ip is reachable. If not, what is the cause, if it is how can I disable it?

    Read the article

  • First requests are painfully slow

    - by winSharp93
    I am running Redmine under IIS using Zoo. Installation was done using the Web Platform Installer and the default configuration has not been touched. However, when using the application, the first requests take very long to complete (sometimes more than one minute). During that time, the ruby.exe causes some CPU load (about 15%). According to the log files, it's mainly the views taking that long to render: Started GET "/redmine/login" for IP at 2012-09-04 09:54:08 +0200 Processing by AccountController#login as HTML Rendered account/login.html.erb within layouts/base (42150.5ms) Completed 200 OK in 43508ms (Views: 43008.5ms | ActiveRecord: 0.0ms) Rendered account/login.html.erb within layouts/base (42435.1ms) Completed 200 OK in 44100ms (Views: 43523.3ms | ActiveRecord: 0.0ms) After the initial delay, further request times are totally acceptable. Any ideas on how to speed up the warmup time?

    Read the article

  • Sendmail relay out of Amazon EC2?

    - by Stephen Belanger
    I have a site running on CentOS 5.4 through Amazon EC2. Unfortunately, Amazon has had nothing but trouble with their entire IP range getting black listed from spam tracking services regularly. I need a mail server, so I setup an smtp server elsewhere that I want to send to, but I can't just send directly to it through PHP because the direct smtp request is way too slow. What I want to do is relay through sendmail, but I've never used sendmail before, so I have no idea how to configure it. All I want is for all emails sent from localhost to be relayed to one specific external server, but I don't know how to do that. I tried to find a tutorial online, but couldn't find anything that was particularly clear as to how I go about doing that. Can anyone help me out?

    Read the article

  • Asterisk Connection not working

    - by Tamas Ionut
    I have installed Asterisk on VirtualBox by following the steps from here. Everything went ok until I got to navigate to an IP to configure Asterisk using FreePBX: 10.0.2.15 (Shouldn't be something like 192.168.x.y?? ). However, when I navigated to that url from outside of VirtualBox, that url pointed to nothing. Also I am logged in as root@localhost. Should I be logged in as root@server? I have also validated the installation as described here and everything went well. I am a complete beginner at Asterisk.

    Read the article

  • how to run an AFS file server on a specific ethernet card (in Debian)

    - by listboss
    I have a linux box running Debian server with minimal number of packages (so no GUI for network management). The box has two ethernet cards, one of which (eth0) is connected to a Mac OSX computer using a cross-cable. I can bring up eth0 and assign a static ip (10.10.11.16) to it. This way I can ssh to the box through the cross-cable. This is what I run on Linux box: ifconfig eth0 10.10.11.16 netmask 255.255.255.0 up I also installed/started a file server (AFS) on Debian. So far, the file server can only be accessed through eth1 which is exposed to my home LAN and www. My goal is to set up the file server so that it's only visible through eth0. Is this possible? and if yes, how can I do it?

    Read the article

  • How to make a DHCP server on virtual machine serves other virtual machines(on different physical machines)?

    - by Tony
    I'm building a virtual cluster with VirtualBox and Opensuse. I have 10 physical machines and need several vms on each. The virtual machines are supposed to be in a "private" network, but still have internet access. I was asked to set up a virtual head node working as DHCP server. I installed DHCP server on the virtual head node and it seems works. On VirtualBox I set 2 network adapters to the head node, one bridged adapter and one internal network. One vm on the same physical machine has been set nic as internal network adapter. The vm can get IP address (so DHCP works) but can't access internet. What should I do? Specifically, what network adapter should I choose for head-node and work-nodes in VirtualBox? What in the virtual machines should I do?

    Read the article

  • I can access \\server via explorer but a program wont

    - by Michael Savage
    From ServerA I can access \\ServerB\Telephony\Files\abcdefgh.pdf using windows explorer. From the same ServerA when I try to access the same file on ServerB using a program (a program that imports files from csv file) I get "File Not Found" error. On \\ServerB\Telephony\ the Share is on and I added the service account that I used to log in to ServerA. I am clueless. Please suggest. (oh, it's a Windows 2008 R2 Server) (btw, I did try IP Address, FQDN but works with Explorer but CVS Importer wont read the path. At one time, I did get Access Denied but I dont get access denied anymore after adding the service account to the share. firewalls are off on the servers) Update: I go to My Computer Network I see many servers but ServerB is not in the list..

    Read the article

  • VPN trace route

    - by Jake
    I am inside an Active Directory (AD) domain and trying to trace route to another AD domain at a remote site, but supposedly connected by VPN in between. the local domain can be accessed at 192.168.3.x and the remote location 192.168.2.x. When I do a tracert, I am suprised to see that the results did not show the intermediate ISP nodes. If I used the public IP of the remote location, then a normal tracert going through every intermediate node would show. 1 <1 ms <1 ms <1 ms 192.168.3.1 2 1 ms <1 ms <1 ms 192.168.3.254 3 7 ms 7 ms 7 ms 212.31.2xx.xx 4 197 ms 201 ms 196 ms 62.6.1.2xx 5 201 ms 201 ms 210 ms vacc27.norwich.vpn-acc.bt.net [62.6.192.87] 6 209 ms 209 ms 209 ms 81.146.xxx.xx 7 209 ms 209 ms 209 ms COMPANYDOMAIN [192.168.2.6] Can someone explain how does this VPN tunnelling works? Does this mean VPN is technically faster than without?

    Read the article

  • How to make AD highly available for applications that use it as an LDAP service

    - by Beaming Mel-Bin
    Our situation We currently have many web applications that use LDAP for authentication. For this, we point the web application to one of our AD domain controllers using the LDAPS port (636). When we have to update the Domain Controller, this has caused us issues because one more web application could depend on any DC. What we want We would like to point our web applications to a cluster "virtual" IP. This cluster will consist of at least two servers (so that each cluster server could be rotated out and updated). The cluster servers would then proxy LDAPS connections to the DCs and be able to figure out which one is available. Questions For anyone that has had experience with this: What software did you use for the cluster? Any caveats? Or perhaps a completely different architecture to accomplish something similar?

    Read the article

  • Connect to development server via switch?

    - by letseatfood
    I apologize upfront if this isn't appropriate for superuser. I asked it on serverfault and was told it was too general for that site. I have a laptop with Vista and it receives it's internet connection wireless. I have an old desktop with Ubuntu 10.04 Server Edition installed and it is setup as a development server with Apache, MySQL, and PHP. This works well, with the server having a static IP address. The server is connected to the router via an Ethernet cable. Is it possible to disconnect the cable that is currently connecting the server and the router, then connect the server and workstation to a switch, so that I am still able to connect to the server via web browser from the workstation? I am trying to eliminate the long ethernet cable connecting the server to the router in the other room. I already have a switch, that is why I asked specifically about it. Thanks and I will be more than happy to clarify!

    Read the article

  • Help with Apache rewriteengine rules

    - by Vinay
    Hello - I am trying to write a simple rewrite rule using the rewriteengine in apache. I want to redirect all traffic destined to a website unless the traffic originates from a specific IP address and the URI contains two specific strings. RewriteEngine On RewriteLog /var/log/apache2/rewrite_kudithipudi.log RewriteLogLevel 1 RewriteCond %{REMOTE_ADDR} ^199\.27\.130\.105 RewriteCond %{REQUEST_URI} !/StringOne [NC, OR] RewriteCond %{REQUEST_URI} !/StringTwo [NC] RewriteRule ^/(.*) http://www.google.com [R=302,L] I put these statements in my virtual host configuration. But the rewriteengine seems to be redirect all requests, whether they match the condition or not. Am I missing something? Thank you. Vinay.

    Read the article

  • Suggestions for a SOHO/Home Asterisk system

    - by James
    I would like to buy a small embedded system that runs Linux and Asterisk. I would like two FXS ports ( to plug analogue phones into ) and one FXO port ( to plug in to my real line to allow access to the POTS ). I would like it to have a USB port to hold storage for voicemail. I really want it for home use so I would like it to be under £150 ( say $250 ), given that you can buy ADSL routers for around this much can any of them be made to run Linux and Asterisk? I don't want a PC as the power usage would be too high. I am looking for something like this ASDL router but open and able to run Asterisk or another open PBX. At worst I would like a box which had one FXO and two FXS and just made them completely available over IP to a full Asterisk system on a low power Atom system.

    Read the article

  • Wired and wireless conections: force Windows to connect to laptop through Ethernet?

    - by danielkza
    I have a desktop connected to the internet and to my home network through Wi-Fi, and a latptop connected to said desktop through an Ethernet cable. But Windows seems to only reach the laptop through Wi-Fi: I want to transfer files through the wired connection instead. Setting up Internet Connectin Sharing and disconnecting the laptop from Wi-Fi altogether doesn't seem like the most elegant solution to me. I also thought about going to the hosts file and setting up the IP address manually, but that would make the laptop completely unavailable if it's not wired, which happens quite often unfortunately. Is there any way for me to tell Windows to use the wired connection for a particular host if possible, and fallback to any other route it finds otherwise?

    Read the article

  • Tunneling HTTP traffic from a particular host/port

    - by knoopx
    Hello, I'm trying to figure out how to access from my development machine (Devel) to a third party web service (www.domain.com) which I am not allowed to directly contact using my office IP address. Here's a basic diagram (i'm not allowed to post images...): http://yuml.me/diagram/scruffy/class/%5BDevel%5D-%5BA%5D,%20%5BA%5D-%5BB%5D,%20%5BB%5D-%5Bwww.domain.com%5D The only machine allowed to access that service is B (production server) but I do neither can directly access it from my development machine (Devel). So in order to access the web service I have to ssh into A, and then from A to B to access www.domain.com Is there any way of tunneling traffic from B to A and then back to my development machine so I can directly access www.domain.com without having to ssh into every box? Devel: My development machine. A, B: Linux servers. I own root access on both. B: Production server www.domain.com: Third party HTTP API production server uses.

    Read the article

  • Drupal + Lighttpd: enabling clean urls (rewriting)

    - by Patrick
    I'm emulating Ubuntu on my mac, and I use it as a server. I've installed lighttpd + Drupal and the following configuration section requires a domain name in order to make clean urls to work. Since I'm using a local server I don't have a domain name and I was wondering how to make it work given the fact the ip of the local machine is usually changing. thanks $HTTP["host"] =~ "(^|\.)mywebsite\.com" { server.document-root = "/var/www/sites/mywebsite" server.errorlog = "/var/log/lighttpd/mywebsite/error.log" server.name = "mywebsite.com" accesslog.filename = "/var/log/lighttpd/mywebsite/access.log" include_shell "./drupal-lua-conf.sh mywebsite.com" url.access-deny += ( "~", ".inc", ".engine", ".install", ".info", ".module", ".sh", "sql", ".theme", ".tpl.php", ".xtmpl", "Entries", "Repository", "Root" ) # "Fix" for Drupal SA-2006-006, requires lighttpd 1.4.13 or above # Only serve .php files of the drupal base directory $HTTP["url"] =~ "^/.*/.*\.php$" { fastcgi.server = () url.access-deny = ("") } magnet.attract-physical-path-to = ("/etc/lighttpd/drupal-lua-scripts/p-.lua") }

    Read the article

  • Routing and Remote access rule not being applied internally (Windows SBS)

    - by Tim Saunders
    Hi, I have a Microsoft Small Business Server. I have pointed an external domain name to the external fixed IP address for the server. In routing and remote access I have defined a service for our subversion server as follows: Incoming port: 8443 Private address: 192.168.10.5 Outgoing port: 8443 192.168.10.5 is our development server, not the SBS (which is at 192.168.10.1) This rule works correctly if I am not on our internal network. However if I am on the internal network this rule does not get applied. What can I do/set so this rule is applied both internally and externally (so users with laptops et, don't keep having to change the URL by which they access the subversion server) Not sure what other info you may need, so please let me know if more details are required. T

    Read the article

  • iptables drop packet by hex string match

    - by Flint
    I got this packet captured with tcpdump but I'm not sure how to use the --hex-string param to match the packet. Can someone show me how to do it? 11:18:26.614537 IP (tos 0x0, ttl 17, id 19245, offset 0, flags [DF], proto UDP (17), length 37) x.x.187.207.1234 > x.x.152.202.6543: [no cksum] UDP, length 9 0x0000: f46d 0425 b202 000a b853 22cc 0800 4500 .m.%.....S"...E. 0x0010: 0025 4b2d 4000 1111 0442 5ebe bbcf 6701 .%[email protected]^...g. 0x0020: 98ca 697d 6989 0011 0000 ffff ffff 5630 ..i}i.........V0 0x0030: 3230 3300 0000 0000 0000 0000 203.........

    Read the article

  • Good quality voice communication software over Internet for windows

    - by ORA600
    I regularly attend over-the-phone meetings, where is a polycom/polispan device on the other side. The quality of the sound is bad, even those whose English is a first language sometimes are struggling to realize what is being said on the other side. I understand this is because of too aggressive audio compression in the line. Does anyone know any good audio chat software which does not over-compress audio stream. The IP channel between two offices is wide enough. In other words, you should be able to listen to a music (not only a speech) from the remote side with good quality. So, Skype is too over-compressing as well. Does anyone know anything like that?

    Read the article

  • Measuring cumulative network statistics per user or per process

    - by zsimpson
    I've been googling for hours -- Under Linux I want to know the cumulative bytes sent and received by user or by process over all ip protocols. The best I've found in my searches is that it's possible to use iptables to mark packets for a user, for example: iptables -t mangle -A OUTPUT -p tcp -m owner --uid-owner test -j MARK --set-mark 1 It appears that "tc" can then shape traffic with that but I just want the statistic -- I don't want to shape the traffic. I want something like: "user U has transmitted used XMB since time Y". I can't figure out how to get statistics from these marked packets. Also, I've looked at nethogs but they seem to be measuring the instantaneous flow and I need cumulative counts. Anyone have ideas?

    Read the article

< Previous Page | 319 320 321 322 323 324 325 326 327 328 329 330  | Next Page >