Search Results

Search found 8384 results on 336 pages for 'laptop batteries'.

Page 324/336 | < Previous Page | 320 321 322 323 324 325 326 327 328 329 330 331  | Next Page >

• 12.04 making BCM4313 card work with aircrack-ng?

  - by Charles Forest

  I'm a real Linux Noob, just started using it (this month) and until now i had no issues. now i'm trying to set-up aircrack-ng on my laptop, but it seems like it's using the worst card possible (or almost) there is a TON of tutorial on this card (seems to be hell to set-up) i have tryed some, but i ended up uninstalling my drivers, messing with my desktops, and ended by having no more "X" to close my windows (i have no clue how i ended there) i just re-installed my linux (took me 2 hours to setup everything again), but now i'm a bit "Scared" to try tutorials randomly again. Right now it says the driver is wl, wich is not the one i want (AFAIK it's not supported) i'm not sure what kind of informations are needed, but here's what i think could be usefull. lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: agpgart-intel 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: i2c-i801 01:00.0 3D controller [0302]: NVIDIA Corporation GF108 [GeForce GT 540M] [10de:0df4] (rev a1) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb WIRELESS CARD 02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac REST... 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: r8169 Kernel modules: r8169 04:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: xhci_hcd Also, if i'm "screwed" with my hardware, just tell me.

  Read the article

• Grub Rescue Unknown Filesystem Error. Grub Corrupted or Filesystem?

  - by nightcrawler

  Now it has happened twice & have been pulling my hairs now... I have installed xubuntu on my external hardisk & have been using it for about 3 months. It has three partitions, one of 500 mb mounted at /boot, 2nd one of 48gb mounted at / & the rest (out of 160gb) is ntfs partition....used as normal external storage. The last storage supposedly acts as a buffer b/w Linux distributions & Win platform, buffer in the sense that it provides a universal channel for data transfers. I have constantly used this external hardisk for data transfers b/w win7 laptop & xubuntu (on this external hd) without any hassle. However, on of my desktops where I have ubuntu I (for the first time) attached this external drive which let me do data transfers where all three partitions properly mounted....but then nasty thing occurred the same that occurred before. I (as usual) tried booting via this external hd (one having xubuntu, one having being formerly used under Ubuntu) I got error Now I am totally devastated because similar thing happened ~6months before when I had fedora 17 in my external hd (instead of xubuntu) & after it was used under ubuntu the same happened...i didn't reported it because I already had planned towards debian instead of rpm! The mystery is that as long as I don't attach this external hd under ubuntu the data never** corrupts whereas under win xp/7 I can use it as a normal usb storage of coarse linux partitions aren’t available under win platforms... **From corrupts I mean hd fails to boot with the error mentioned however cant say whether data within remains untouched? It seems that my grub & or MBR is corrupted. Please sir guide me to solve this issue also why I cant attach & use linux external hds under linux platform Disk /dev/sdc: 160.0 GB, 160041884672 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581806 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004e7d0 Device Boot Start End Blocks Id System /dev/sdc1 * 2048 976895 487424 83 Linux /dev/sdc2 978942 96874495 47947777 5 Extended /dev/sdc3 96874496 312575999 107850752 7 HPFS/NTFS/exFAT /dev/sdc5 978944 94726143 46873600 83 Linux /dev/sdc6 94728192 96874495 1073152 82 Linux swap / Solaris I can recall for sure that have seen a thread here when a similar problem occurred & in response someone gave solution of how to mount (now invisible) partitions & recover important data in them. I have misplaced that URL so if any can guide me thither because my important documents resides in / partition What I already have done: Without success I have tried this & related solutions What I plan to do: I believe that filesystem has corrupted & would you recommend solution like this provided I cant recall whether my /boot (500mb) partition was ext4 or ext2 though I am sure that my / (48gb) partition was ext4 UPDATE 1 Attached my external hd under Ubuntu ran followinf command as root grub-install /dev/sdc where /dev/sdc was my external hd containing corrupted xubuntu....it reported all done! I re-ran fdisk -l but to my disappointment it reported Disk /dev/sdc: 160.0 GB, 160041884672 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581806 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b6b9167 Disk /dev/sdc doesn't contain a valid partition table ...& now I can't even access its ntfs partition (former /dev/sdc3) please help? UPDATE 2 TestDisk (by cgsecurity) failed at founding any partition table :( TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sdc - 160 GB / 149 GiB - CHS 19457 255 63 Partition Start End Size in sectors

  Read the article

• Easy Made Easier - Networking

  - by dragonfly

      In my last post, I highlighted the feature of the Appliance Manager Configurator to auto-fill some fields based on previous field values, including host names based on System Name and sequential IP addresses from the first IP address entered. This can make configuration a little faster and a little less subject to data entry errors, particularly if you are doing the configuration on the Oracle Database Appliance itself.     The Oracle Database Appliance Appliance Manager Configurator is available for download here. But why would you download it, if it comes pre-installed on the Oracle Database Appliance? A common reason for customers interested in this new Engineered System is to get a good idea of how easy it is to configure. Beyond that, you can save the resulting configuration as a file, and use it on an Oracle Database Appliance. This allows you to verify the data entered in advance, and in the comfort of your office. In addition, the topic of this post is another strong reason to download and use the Appliance Manager Configurator prior to deploying your Oracle Database Appliance.     The most common source of hiccups in deploying an Oracle Database Appliance, based on my experiences with a variety of customers, involves the network configuration. It is during Step 11, when network validation occurs, that these come to light, which is almost half way through the 24 total steps, and can be frustrating, whether it was a typo, DNS mis-configuration or IP address already in use. This is why I recommend as a best practice taking advantage of the Appliance Manager Configurator prior to deploying an Oracle Database Appliance.     Why? Not only do you get the benefit of being able to double check your entries before you even start on the Oracle Database Appliance, you can also take advantage of the Network Validation step. This is the final step before you review all the data and can save it to a text file. It can be skipped, if you aren't ready or are not connected to the network that the Oracle Database Appliance will be on. My recommendation, though, is to run the Appliance Manager Configurator on your laptop, enter the data or re-load a previously saved file of the data, and then connect to the network that the Oracle Database Appliance will be on. Now run the Network Validation. It will check to make sure that the host names you entered are in DNS and do resolve to the IP addresses you specifiied. It will also ping the IP Addresses you specified, so that you can verify that no other machine is already using them (yes, that has happened at customer sites).     After you have completed the validation, as seen in the screen shot below, you can review the results and move on to saving your settings to a file for use on your Oracle Database Appliance, or if there are errors, you can use the Back button to return to the appropriate screen and correct the data. Once you are satisfied with the Network Validation, just check the Skip/Ignore Network Validation checkbox at the top of the screen, then click Next. Is the Network Validation in the Appliance Manager Configurator required? No, but it can save you time later. I should also note that the Network Validation screen is not part of the Appliance Manager Configurator that currently ships on the Oracle Database Appliance, so this is the easiest way to verify your network configuration.     I hope you are finding this series of posts useful. My next post will cover some aspects of the windowing environment that gets run by the 'startx' command on the Oracle Database Appliance, since this is needed to run the Appliance Manager Configurator via a direct connected monitor, keyboard and mouse, or via the ILOM. If it's been a while since you've used an OpenWindows environment, you'll want to check it out.

  Read the article

• WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

  - by el10780

  After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

  Read the article

• Antenna Aligner Part 7: Connecting the dots

  - by Chris George

  The app is basically ready, so I eagerly started to sort out creating the application entry in iTunes Connect. It's mostly intuitive actually, although I did have to create yet another icon for iTunes sized 512x512 pixels, damn lucky I did the original graphics as vector! It took me longer to write the application description than anything else, I'm so not a tech author! I didn't like the way you have to 'make up' an SKU (Stock Keeping Unit) number. I have to do some googling to find out that it really doesn't matter what it is! It should be more obvious what to do from the actual website itself. That aside, the rest of it was actually fairly straightforward. As well as the details of the application, iPhone and iPad screenshots were also required. This posed somewhat of a problem. The iPhone ones were easy (as I have one!), but I do not (yet) own an iPad . So I thought I'd leave the iPad screenshots out for now. Once the application details were sorted, I moved onto the rights and pricing. At the start of the project I had made the decision that I wouldn't charge any more than the lowest amount £0.59. I believe there is a market for this, but as my first foray into app development I didn't want to take the mick. I did realise, however, that I had built my app with a developer certificate and provisioning profile. This was fairly quickly corrected, and again Nomad made this very easy to switch over to the distribution certificate and provisioning profile. With a sense of excitement I cracked open iTunes connect and clicked the upload button ... ...slight snag... . when the Nomad project was started, Apple allowed uploads of these binaries via iTunes Connect. But this is no longer possible, the only upload path is via the Application Loader available from the Apple Developer program. This itself has one limitation, it only runs on a mac! D'OH!!!  Actually my language was somewhat more colourful when this fact came to light. After picking my laptop up off the floor and putting it back together... ok only joking, but I did nearly throw it out of frustration!... I started to consider the options; I briefly entertained the idea of buying a cheap mac from ebay... no, that defeats the whole object of what I'm doing, plus my wife wouldn't be impressed there are some guys out there in the interweb who will upload your app for a small fee...but I don't really like the idea of giving some faceless email address my apple developer login details, as well as my app binary! find some willing friend with a mac who would kindly let me use it... obviously this is the only sensible option. In the meantime, I informed the Nomad team about this slight 'issue' and they are currently investigating possible solutions...

  Read the article

• Graphics trouble after resuming from hibernate or suspend

  - by Voyagerfan5761

  I have a Dell Inspiron 2650 (with NVidia graphics, using nouveau drivers) that I'm using to try out Ubuntu. It's all great, except that Hibernate and Suspend aren't usable. Yes, I know that questions about power-save issues are rampant in the Linux support universe, but it seems that every time I find a solution it's for a very specific hardware combination and doesn't apply to me. So anyway, here goes. When I resume from either power-saving mode, I'll get graphics problems anywhere on the range from a few scattered random-colored pixels that won't change; all the way to full-screen patterns that don't change as I move the mouse, hit keys on the keyboard, or even bring up the shutdown dialog using the power button. Those full-screen issues (which may involve stripes with random pixels, partial black screen, or both) always end in me forcing the machine to shut down by holding the power button. I haven't done much testing yet to determine what severity level is most commonly associated with each mode, but I do avoid using either power-save option because of these issues. I'll add info on my hardware as I can gather it (no home internet connection, and this laptop is tethered to my desk by a dead battery and casing degradation). Please feel free to request something specific in the question comments. Hardware Info See this hardinfo report for my system's hardware configuration. (No, my username is not "myuser"; I sanitized hardinfo's output before publishing it.) Screenshots These screenshots are from a relatively mild occurrence, which happened after the second hibernation I took that session. The first one worked great, though I used the wireless card and Firefox heavily between the two hibernation attempts. Take a look at what happened when I opened my home directory in Nautilus and scrolled it: See below for the situations I've tested so far. The real trouble comes when the machine resumes to an unusable state; in such cases I can't even unlock the screen or properly reboot, much less take a screenshot. I have a hunch that putting a CD in the drive will cause such major failures, and I will try that at some point; see related question. Situations Tested Maverick (10.10) Suspend Seems to suspend nicely with nothing running Seems to suspend nicely with flash drive plugged in On resume from suspend with no flash drive, Terminal and gedit running: Funky graphics on top of log output, then blank screen with pixelated cursor; no response to power button (normally will shutdown 60 seconds later) Hibernate Seems to hibernate nicely with nothing running Seems to hibernate nicely with a few apps (Terminal, Mouse preferences) running Seems to not hibernate when flash drive plugged in Seems to not hibernate when System Monitor is running Have encountered failed hibernation (after several hours and one successful hibernate/thaw cycle) with no external media connected and no programs running except normal background stuff Natty LiveCD (11.04_2010-12-22) When I tested it, Natty wouldn't stay logged in. It played part of the login sound and then [ OK ] appeared in the top right corner (white-on-black terminal text) for a few seconds. Then it kicked me back to the Unlock screen. It did that four times before I gave up and just tested suspend from the Unlock screen. Suspend Resumed to vertical gray and black lines 2px (?) wide, then shifted to vertical "jail bars" of black over a black screen with above-described random pixels and mouse pointer. No apparent response to input from mouse (clicking randomly). Keyboard and touchpad unrecognized.

  Read the article

• Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect

  - by user287529

  Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect. I'm using Ubuntu 12.04 on an Acer Aspire 5742-7645 laptop with 4GB memory, Intel Core i3 processor, Intel HD Graphics, DVD drive, 802.1 b/g/n, and 500 GB HD. I connect to my router via a wireless connection. I have installed Virutalbox 4.1.12 from the Ubuntu Software Center and installed Guest additions 4.1.12 in the Windows 7 guest session. I have Windows XP and Windows 7 installed as guests in Virtual box The network settings are different for XP and 7 – see below. Network Settings XP guest = Adapter 1: PCnet-FAST III (NAT) - Network works perfectly and has worked well for several years. Network Settings Win 7 = Adapter 1: Intel PRO/1000 MT Desktop (Bridged adapter, eth1) Promiscuous Mode = allow all Cable connected = checked When I originally installed Windows 7, I tried NAT and the guest network would not connect. Once I changed the setting to the above (Bridged) the Network worked perfectly. However, what I believe is after updates (not sure if it was an Ubuntu or Windows update) the guest network stopped working and I can not get it to connect. Interfaces file content auto lo iface lo inet loopback Ifconfig yields lou@lou-Aspire-5742:~$ ifconfig eth0 Link encap:Ethernet HWaddr 1c:75:08:09:f6:5c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 Link encap:Ethernet HWaddr 4c:0f:6e:7c:9f:01 inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4e0f:6eff:fe7c:9f01/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18095 errors:2 dropped:0 overruns:0 frame:24344 TX packets:9281 errors:47 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5301926 (5.3 MB) TX bytes:1441885 (1.4 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3208 errors:0 dropped:0 overruns:0 frame:0 TX packets:3208 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:294088 (294.0 KB) TX bytes:294088 (294.0 KB) Ipconfig yields the following: Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::38ba:dbca:a21d:c3d1%13 Autoconfiguration IPv4 Address. . : 169.254.195.209 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{B292E440-679D-4FC5-8E34-77D6804669C8}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : I'm not sure what else to do. Can someone provide the troubleshooting steps to determine what the problem is and possible solution?

  Read the article

• Cloud Computing Pricing - It's like a Hotel

  - by BuckWoody

  I normally don't go into the economics or pricing side of Distributed Computing, but I've had a few friends that have been surprised by a bill lately and I wanted to quickly address at least one aspect of it. Most folks are used to buying software and owning it outright - like buying a car. We pay a lot for the car, and then we use it whenever we want. We think of the "cloud" services as a taxi - we'll just pay for the ride we take an no more. But it's not quite like that. It's actually more like a hotel. When you subscribe to Azure using a free offering like the MSDN subscription, you don't have to pay anything for the service. But when you create an instance of a Web or Compute Role, Storage, that sort of thing, you can think of the idea of checking into a hotel room. You get the key, you pay for the room. For Azure, using bandwidth, CPU and so on is billed just like it states in the Azure Portal. so in effect there is a cost for the service and then a cost to use it, like water or power or any other utility. Where this bit some folks is that they created an instance, played around with it, and then left it running. No one was using it, no one was on - so they thought they wouldn't be charged. But they were. It wasn't much, but it was a surprise.They had the hotel room key, but they weren't in the room, so to speak. To add to their frustration, they had to talk to someone on the phone to cancel the account. I understand the frustration. Although we have all this spelled out in the sign up area, not everyone has the time to read through all that. I get that. So why not make this easier? As an explanation, we bill for that time because the instance is still running, and we have to tie up resources to be available the second you want them, and that costs money. As far as being able to cancel from the portal, that's also something that needs to be clearer. You may not be aware that you can spin up instances using code - and so cancelling from the Portal would allow you to do the same thing. Since a mistake in code could erase all of your instances and the account, we make you call to make sure you're you and you really want to take it down. Not a perfect system by any means, but we'll evolve this as time goes on. For now, I wanted to make sure you're aware of what you should do. By the way, you don't have to cancel your whole account not to be billed. Just delete the instance from the portal and you won't be charged. You don't have to call anyone for that. And just FYI - you can download the SDK for Azure and never even hit the online version at all for learning and playing around. No sign-up, no credit card, PO, nothing like that. In fact, that's how I demo Azure all the time. Everything runs right on your laptop in an emulated environment.  

  Read the article

• PowerShell and SMO – be careful how you iterate

  - by Fatherjack

  I’ve yet to have a totally smooth experience with PowerShell and it was late on Friday when I crashed into this problem. I haven’t investigated if this is a generally well understood circumstance and if it is then I apologise for repeating everything. Scenario: I wanted to scan a number of server for many properties, including existing logins and to identify which accounts are bestowed with sysadmin privileges. A great task to pass to PowerShell, so with a heavy heart I started up PowerShellISE and started typing. The script doesn’t come easily to me but I follow the logic of SMO and the properties and methods available with the language so it seemed something I should be able to master. Version #1 of my script. And the results it returns when executed against my home laptop server. These results looked good and for a long time I was concerned with other parts of the script, for all intents and purposes quite happy that this was an accurate assessment of the server. Let’s just review my logic for each step of the code at the top. Lines 1 to 7 just set up our variables and write out the header message Line 8 our first loop, to go through each login on the server Line 10 an inner loop that will assess each role name that each login has been assigned Line 11 a test to see if each role has the name ‘sysadmin’ Line 13 write out the login name with a bright format as it is a sysadmin login Line 17 write out the login name with no formatting It is quite possible that here someone with more PowerShell experience than me will be shouting at their screen pointing at the error I made but to me this made total sense. Until I altered the code, I altered lines 6 and 7 of code above to be: $c = $Svr.Logins.Count write-host “There are $c Logins on the server” This changed my output to look like this: This started alarm bells ringing – there are clearly not 13 logins listed So, let’s see where things are going wrong, edit the script so it looks like this. I’ve highlighted the changes to make Running this code shows me these results Our $n variable should count up by one for each login returned and We are clearly missing some logins. I referenced this list back to Management Studio for my server and see the Logins as below, where there are clearly 13 logins. We see a Login called Annette in SSMS but not in the script results so I opened that up and looked at its properties and it’s server roles in particular. The account has only public access to the server. Inspection of the other logins that the PowerShell script misses out show they too are only members of the public role. Right now I can’t work out whether there is a good reason for this and if it should be expected behaviour or not. Please spend a few minutes to leave a comment if you have an opinion or theory for this. How to get the full list of logins. Clearly I needed to get a full list of the logins so set about reviewing my code to see if there was a better way to iterate through the roles for each login. This is the code that I came up with and I think it is doing everything that I need it to. It gives me the expected results like this: So it seems that the ListMembers() method is the trouble maker in my first versions of the code. I would have expected that ListMembers should return Logins that are only members of the public role, certainly Technet makes no reference to it being left out in it’s Login.ListMembers details. Suffice to say, it’s a lesson learned and I will approach using it with caution in future circumstances.

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• trying to setup wireless

  - by JohnMerlino

  I'm trying to set up wireless on vostro 1520 dell laptop, with latest Ubuntu install. Here's the output of some of the commands that I was told to run: lshw -C network viggy@ubuntu:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 03 serial: 00:24:e8:da:84:25 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.2.6 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:47 ioport:3000(size=256) memory:f6004000-f6004fff memory:f6000000-f6003fff memory:f6020000-f603ffff *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0e:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:fa000000-fa003fff *-network DISABLED description: Wireless interface physical id: 1 logical name: wlan0 serial: 0c:60:76:05:ee:74 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-29-generic firmware=N/A multicast=yes wireless=IEEE 802.11bg lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 1a:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01) 1a:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) 1a:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. At this point in time, I don't have wireless.

  Read the article

• Wireless device bug on 13.10. BCM4313 registers as eth1 instead of wlan0 and no internet access

  - by user205691

  My Hotel wiFi requires me to login with a username & password after connecting to the hotspot. So, my browser would open a page with username & passwrd fields to login and then connect to internet. But unfortunately, firefox & chromium dont seem to work. i dont think it is browser related but a setting for the wifi router or driver which is creating this issue. using Broadcom 801.11 STA wireless driver (proprietary). tried open source as well but same result !! The image linked below shows my wifi connection setting & Chromium. The login page itself comes up after a long time and after entering the credentials, it keeps loading for ever !! it is the same case for every other browser.. so i dont think its browser issue but something to do with wifi setting or network manager stuff.. interestingly, i am able to connect to WiFi networks with WPA key without any issue. Adhoc hotspot is a problem and that is my regular home network :( .. I hope i can get some help solving this issue ! I have tried repeating the same hotspot after login from my android, by creating a virtual repeater with WPA key and it works. I can browse on ubuntu using this method.. but cant be doing this regularly ! I tried loading the same login page of the hotel wifi while browsing through my repeater wifi created on mobile and screen shot attached below. the page loads up quick and easy.. so this means something is wrong with the way network manager handles adhoc connectivity & login ?? i installed wicd0 but it crashes on startup and not helpful at all ! Screenshot of Chromium page Login page with repeated hotspot ifconfig in my terminal results: krishna@krishna-HP-ENVY-4-Notebook-PC:~$ ifconfig eth0 Link encap:Ethernet HWaddr 28:92:4a:1d:54:fa UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr e0:06:e6:89:fa:49 inet addr:10.24.1.71 Bcast:10.24.1.255 Mask:255.255.255.0 inet6 addr: fe80::e206:e6ff:fe89:fa49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10940 errors:0 dropped:0 overruns:0 frame:348431 TX packets:6611 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7669631 (7.6 MB) TX bytes:864195 (864.1 KB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2146 errors:0 dropped:0 overruns:0 frame:0 TX packets:2146 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:166120 (166.1 KB) TX bytes:166120 (166.1 KB) I wonder why is the wireless configured under eth1 ? I think this is a bug with earlier ubuntu versions, but is this normal in 13.10 or is there a wrong configuration here ? The wireless device in my pc is BCM4313 and i have installed the bcmwl-kernel-sources, wireless-tools to support the device. i also reinstalled the bcmwl-kernel as suggested on broadcom website, via synaptic package manager. Nothing has changed this situation ! I tried booting into liveUSB and then ifconfig results show wireless under wlan0. But then the wireless connects and loads the login page. So is the problem with the device configuration now ? i really want to get this fixed before i start configuring the other stuff like ATI graphics and such on the laptop for overheating.. lack of internet access is too bad a bug for me :P any help is appreciated!

  Read the article

• Why Apple’s New SDK Limitation is So Offensive

  - by TStewartDev

  I am not an Apple fanboy, nor have I ever been. However, I have owned a Mac, an iPod, and an iPhone in my lifetime, and for more than a decade, I have defended Apple against the untruths that the haters so enjoy spewing. I encouraged my wife to buy a MacBook when she needed a new laptop two years ago, and I often recommend them to my friends and relatives. I have proudly and happily used my first generation iPhone for nearly three years. Now, for the first time in well over ten years, I find myself ready to swear off Apple and encourage everyone I know to do the same. I was disappointed when Apple wouldn't allow native apps, but I still bought the iPhone. I've stomached their ambiguous app approval process even though it's apparent that Steve may just reject your app because he doesn't like you or feels threatened by you (I'm still lamenting the rejection of the Google Voice app). But, as a developer, I can no longer tolerate Apple's terms and the kind of totalitarian control they indicate Apple wants. In case you are not already familiar, Apple has dictated in their OS 4.0 SDK license agreement (the now infamous Section 3.3.1) that all apps developed for the iPhone must be coded in C, C++, or Objective C, and moreover, that using any cross-compiling platforms is a violation of the agreement. For those of you who aren't developers, let me try to illustrate why this angers those of us who are. Imagine you're a professional writer. You've had articles published in some journals and magazines, and you've got a couple popular books out there, too. You've got an idea for a new book, and so you take it to your publisher. Your publisher agrees that it's a good idea. "But," says the publisher, "we want to hold our books to a tighter standard so that our readers get the experience we want them to have. Therefore, from now on, all our writers may only use words from this list of the 10,000 most common English words. Furthermore, if you cite any other works or quote anyone, they must comply with that same list, or you'll have to rewrite the entire work as well in case our readers want to look up your citation." What do you do? If your work is a children's book, this probably isn't a big deal to you. If it's an autobiography, textbook, or even a novel, though, you're going to have a lot of trouble describing your content with only common words. It's going to take you longer to complete your book, too, since you'll be looking up less common words frequently to see if you can use them. You could always go to another publisher, but this one has the best ability to distribute your book. The next largest distributor can only do a quarter as much. You could abandon the project altogether, but then everyone loses. Isn't this a silly scenario? Who would put such a limitation on writers? Yet this is very much what Apple is doing. They are using their dominant position in the market to coerce developers to write their apps exclusively for the iPhone OS by making it too expensive to write for multiple platforms. It is at least a threefold attack, striking at Adobe who is set to release a compiler that lets Flash source be compiled to iPhone binaries; striking at Google whose Android platform stands the best chance at the moment of providing serious competition to the iPhone; and reinforcing their own strong position by keeping popular apps exclusively to iPhone. And while developers are already very upset about this, the sad fact is that most of us will cave and give in to Apple because consumers don't know any better. They will continue to buy Apple's toy forcing developers to play Apple's maniacal game in order to make any money, at least until Steve Jobs decides he doesn't like them or he intends to release a competing application (bye-bye OpenFeint). Apple has been kept in check on the desktop front by a very dominant Microsoft, but I'm afraid that their success with iPods, iTunes, and iPhones has created a monster that we may have to bear until it is slain by an anti-trust suit or dies with the retirement of Steve Jobs.

  Read the article

• Video works with 'Try me' but not after install. What is the difference? U12.04LTS,

  - by HarveyP

  My hard drive got corrupted so I did a reinstall. Tested Youtube in FF during 'try me' and it worked - jerky, but it worked. Instal without all the updates (576 outstanding now) in order to get ff installed as per the demo - to no avail. In 'try me' mode ff NEVER crashed! After install ff crashed whilst I was typing in 'youtube' in the address field. When I finally got to youtube - no video. What is the difference between ff in try me and ff after install? Off to try some selected updates now to see if I can see it for myself. In previous installation I had several profiles and aliased ff with -safe-mode switch to simplify startup of most stable ff. Also found that ff startup in graphic mode worked better (but still without video) with all of the extensions disabled and all of the plugins set to "ask" and always denied ... I have SiS graphic card in SiS Motherboard for XP and ancient Hyundai ImageQuest QV770 monitor. I have Ubuntu 12.04.01 LTS 1 day after install with only the immediate upgrades requested to language pack (English UK). Using FR Alternative keyboard. Connected with domestic wifi network from Orange (FT) I really want to use Skype, but won't bother installing it (again) without video as I can do my sms on FB - whilst ff is not crashed ... Update ... Is something overflowing? I have just had to reboot in order to get ff to restart in any way shape or form - restart on crash form generates new crash form, etc. It was however a good half hour before it crashed so some improvement over conditions before disk corruption. I have now installed all of the critical updates (332 recommended updates still outstanding) which included some relating to ff. Still no video. Still crashing - especially when on Grepolis website. Since the re-install I have had a lovely 1024x768 screen, but after last ff crash and reboot I got a message about 'low graphics mode' and 'setting things myself'. I was not sufficiently tuned in at the time to take proper note - I have no doubt I shall see it again and shall report accordingly. I still have only laptop options for my screen and do not know how to rectify this. Spent a few days with ubuntu on a different, newer machine which has now suffered a graphics breakdown. Returned to this old one again, but with new flat screen Monitor. Found SIS drivers for my graphics BUT it is intended for Red Hat 7.2. I chose this over the version for 7.0 because I thought what the hell, I might not be able to do anything with either of them but this is the later one ... The file will not open with software manager - found a similar problem on Overclock but it has not helped me to install this driver. File name is sis_drv.o-410 and it is currently idling away in my Downloads folder ... I have tried the solution offered on another sis problem, but this shows that my xserver-xorg-video-sis driver is up to date. I am now at a loss as to how to proceed if I can't install the latest sis driver from sis ... Does nobody know how FF changes from "try-me" to "installed"? Any time I MUST have video I reboot from the disk again, but this is tedious! Also one of the things I mock most about MS is the constant rebooting ... UPDATE 10/6/2014 I have installed chromium-browser - worse, crashes even more often than ff.I have installed epiphany - better; Video works but not the associated soundtrack.FireFox is version 14.01 in 'try me' and version 29.0 from my install. Would it be useful to try to downgrade FireFox in order to get video?

  Read the article

• Wireless connection works but the internet is too slow to use in Ubuntu 11.04

  - by Garrin

  The internet is so slow as to be unusable. And I'm not being picky. Even after minutes I can't get my Google home page to load. I tried installing a package through apt-get and was getting rates between 0 and a few hundred bytes/s. That's bytes, not kilobytes! Mostly 0 however (no exaggeration, it spends large amounts of time stalled). And I would go to a speed test web site of some kind but I can't since nothing will load. Briefly put, the laptop I am using was connected to two wireless networks while using Ubuntu 11.04 without any issues before this. It was also connected to a wired network without any issues. It dual boats Windows 7 which has never had any issues, not even with the current wireless network. Just to be clear, on the current wi-fi network, Windows 7 encounters no issues (speedtest.net puts the network speed at 1mb/s) but my network connection in Ubuntu 11.04 is so slow as to literally be unusable. I am unfamiliar with the router except for the fact that it boasts a Rogers logo (that's a large ISP/cable provider in Canada for those not familiar with the land of igloos and polar bears). I am far from the router and some desktop widget I use tells me the signal strength is at 58% (it seems fairly reliable and this would appear to match up with the filled bars in the network icon). I should also mention I'm just renting a room in this house so I'm not the network administrator and while I can access the 192.168.0.1 router page, the password wasn't set to 'password' so it's not much use to me. Here are a bunch of commands I ran which don't tell me a whole lot but I thought might be more instructive to the wise around here: lspci (just showing my network card): 05:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) This one is self explanatory. PING www.googele.com (216.65.41.185) 56(84) bytes of data. 64 bytes from nnw.net (216.65.41.185): icmp_req=1 ttl=51 time=267 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=2 ttl=51 time=190 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=3 ttl=51 time=212 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=4 ttl=51 time=207 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=5 ttl=51 time=220 ms --- www.googele.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4003ms rtt min/avg/max/mdev = 190.079/219.699/267.963/26.121 ms ifconfig eth0 Link encap:Ethernet HWaddr 20:6a:8a:02:20:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:960 (960.0 B) TX bytes:960 (960.0 B) wlan0 Link encap:Ethernet HWaddr 20:7c:8f:05:c6:bf inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::227c:8fff:fe05:c6bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:982 errors:0 dropped:0 overruns:0 frame:0 TX packets:658 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:497250 (497.2 KB) TX bytes:95076 (95.0 KB) Thank you

  Read the article

• Cannot get ATI Drivers installed

  - by bittoast67

  I am trying to install the Catalyst driver. The best I can get is a strange resolution problem and firefox acts all wonkt. The worst I have gotten is low graphics mode in which I just reinstall Ubuntu. I have a HP Pavilion Dv7 laptop. With Radeon 3200 HD. I plan to try again with a fresh install of Ubuntu 12.4.3 as I have heard its the most compatible. This is what I have done: I have tried just the easy way of going to synaptic and installing the drivers that way. the fglrx package (not the fglrx update). And if memory serves I think that boots me into low graphics mode. So, fresh install of Ubuntu and tried again. I have done everything a couple times from this site (http://wiki.cchtml.com/index.php/Ubuntu_Precise_Installation_Guide) following every instruction to a T. That gets me something, such as a lowered fan speed and a much cooler computer, but I also lose most of my resolution. And displays says its the best resolution I can get. I also have a very screwy firefox. Using this method I can see AMD Catalyst Control Center in my dash (two of them really one administrator and one not) but when I try to open it it says no amd driver detected. So again, ubuntu reinstall. I have tried the GUI method from the Legacy driver I got from AMD's site. It runs through smoothly and at the very end after I exit the installer it gives me an error. I have also tried various other methods using terminal, as well as various different drivers (the one from the amd's site and the one suggested in the above link for my graphics card) both to no avail. When I try the method in the link on number 2, and I get the super low res and screwy fire fox. I type in, fglrxinfo ,and get a badrequest error. I have yet to type in fglrxinfo and get anything like what I am supposed to. UPDATE: I am now currently reinstalling Ubuntu 12.4. I tried the above mentioned link - thank you very much!- just to see on the previously failed driver attempt by following the purge commands. And to no avail when typing fglrxinfo I still get the badrequest thing. I will update again after a try with a true fresh install. Thanks again!! UPDATE: Alright everyone. Still no go. I have done everything word per word in the provided tutorial. I have rebooted my computer again to a fucked up resolution and this is what I get when typing fglrxinfo: $ fglrxinfo X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 153 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 12 Current serial number in output stream: 12 I would like to add that when installing this file: fglrx_8.970-0ubuntu1_amd64.deb I got this: Building initial module for 3.8.0-29-generic Error! Bad return status for module build on kernel: 3.8.0-29-generic (x86_64) Consult /var/lib/dkms/fglrx/8.970/build/make.log for more information. update-initramfs: deferring update (trigger activated) Processing triggers for ureadahead ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-29-generic Processing triggers for libc-bin ... ldconfig deferred processing now taking place Any ideas? Anyone? I cant for the life of me figure out what I am doing wrong.

  Read the article

• Cloud Adoption Challenges

  - by Herve Roggero

  Originally posted on: http://geekswithblogs.net/hroggero/archive/2013/11/07/cloud-adoption-challenges.aspxWhile cloud computing makes sense for most organizations and countless projects, I have seen customers significantly struggle with cloud adoption challenges. This blog post is not an attempt to provide a generic assessment of cloud adoption; rather it is an account of personal experiences in the field, some of which may or may not apply to your organization. Cloud First, Burst? In the rush to cloud adoption some companies have made the decision to redesign their core system with a cloud first approach. However a cloud first approach means that the system may not work anymore on-premises after it has been redesigned, specifically if the system depends on Platform as a Service (PaaS) components (such as Azure Tables). While PaaS makes sense when your company is in a position to adopt the cloud exclusively, it can be difficult to leverage with systems that need to work in different clouds or on-premises. As a result, some companies are starting to rethink their cloud strategy by designing for on-premises first, and modify only the necessary components to burst when needed in the cloud. This generally means that the components need to work equally well in any environment, which requires leveraging Infrastructure as a Service (IaaS) or additional investments for PaaS applications, or both.  What’s the Problem? Although most companies can benefit from cloud computing, not all of them can clearly identify a business reason for doing so other than in very generic terms. I heard many companies claim “it’s cheaper”, or “it allows us to scale”, without any specific metric or clear strategy behind the adoption decision. Other companies have a very clear strategy behind cloud adoption and can precisely articulate business benefits, such as “we have a 500% increase in traffic twice a year, so we need to burst in the cloud to avoid doubling our network and server capacity”. Understanding the problem being solved through by adopting cloud computing can significantly help organizations determine the optimum path and timeline to adoption. Performance or Scalability? I stopped counting the number of times I heard “the cloud doesn’t scale; our database runs faster on a laptop”.  While performance and scalability are related concepts, they are nonetheless different in nature. Performance is a measure of response time under a given load (meaning with a specific number of users), while scalability is the performance curve over various loads. For example one system could see great performance with 100 users, but timeout with 1,000 users, in which case the system wouldn’t scale. However another system could have average performance with 100 users, but display the exact same performance with 1,000,000 users, in which case the system would scale. Understanding that cloud computing does not usually provide high performance, but instead provides the tools necessary to build a scalable system (usually using PaaS services such as queuing and data federation), is fundamental to proper cloud adoption. Uptime? Last but not least, you may want to read the Service Level Agreement of your cloud provider in detail if you haven’t done so. If you are expecting 99.99% uptime annually you may be in for a surprise. Depending on the component being used, there may be no associated SLA at all! Other components may be restarted at any time, or services may experience failover conditions weekly ( or more) based on current overall conditions of the cloud service provider, most of which are outside of your control. As a result, for PaaS cloud environments (and to a certain extent some IaaS systems), applications need to assume failure and gracefully retry to be successful in the cloud in order to provide service continuity to end users. About Herve Roggero Herve Roggero, Windows Azure MVP, is the founder of Blue Syntax Consulting (http://www.bluesyntax.net). Herve's experience includes software development, architecture, database administration and senior management with both global corporations and startup companies. Herve holds multiple certifications, including an MCDBA, MCSE, MCSD. He also holds a Master's degree in Business Administration from Indiana University. Herve is the co-author of "PRO SQL Azure" and “PRO SQL Server 2012 Practices” from Apress, a PluralSight author, and runs the Azure Florida Association.

  Read the article

• Software and/(x)or Hardware Projects for Pre-School Kids

  - by haylem

  I offered to participate at my kid's pre-school for various activities (yes, I'm crazy like that), and one of them is to help them discover extra-curricular (big word for a pre-school, but by lack of a better one... :)) hobbies, which may or may not relate to a professional activity. At first I thought that it wouldn't be really easy to have pre-schoolers relate to programming or the internal workings of a computer system in general (and I'm more used to teaching middle-school to university-level students), but then I thought there must be a way. So I'm trying to figure out ways to introduce very young kids (3yo) to computer systems in a fun and preferably educational way. Of course, I don't expect them to start smashing the stack for fun and profit right away (or at least not voluntarily, though I could use the occasion for some toddler tests...), but I'm confident there must be ways to get them interested in both: using the systems, becoming curious about understanding what they do, interacting with the systems to modify them. I guess this setting is not really relevant after all, it's pretty much the same as if you were aiming to achieve the same for your own kids at home. Ideas Considering we're talking 3yo pre-schoolers here, and that at this age some kids are already quite confident using a mouse (some even a keyboard, if not for typing, at least to press some buttons they've come to associate with actions) while others have not yet had any interaction with computers of any kind, it needs to be: rather basic, demonstrated and played with in less then 5 or 10 minutes, doable in in groups or alone, scalable and extendable in complexity to accommodate their varying abilities. The obvious options are: basic smallish games to play with, interactive systems like LOGO, Kojo, Squeak and clones (possibly even simpler than that), or thngs like Lego Systems. I guess it can be a thing to reflect on both at the software and the hardware levels: it could be done with a desktop or laptop machine, a tablet, a smartphone (or a crap-phone, for that matter, as long as you can modify it), or even get down to building something from scratch (Raspberry Pi and Arduino being popular options at the moment). I can probably be in the form of games, funny visualizations (which are pretty much games) w/ Prototype, virtual worlds to explore. I also thought on the moment (and I hope this won't offend anyone) that some approaches to teaching pets could work (reward systems, haptic feedback and such things could quickly point a kid in the right direction to understanding how things work, in a similar fashion - I'm not suggesting to shock the kids!). Hmm, Is There an Actual Question in There? What type of systems do you think might be a good fit, both in terms of hardware and software? Do you have seen such systems, or have anything in mind to work on? Are you aware of some research in this domain, with tangible results? Any input is welcome. It's not that I don't see options: there are tons, but I have a harder time pinpointing a more concrete and definite type of project/activity, so I figure some have valuable ideas or existing ones. Note: I am not advocating that every kid should learn to program, be interested in computer systems, or that all of them in a class would even care enough to follow such an introduction with more than a blank stare. I don't buy into the "everybody would benefit from learning to program" thing. Wouldn't hurt, but not necessary in any way. But if I can walk out of there with a few of them having smiled using the thing (or heck, cried because others took them away from them), that'd be good enough. Related Questions I've seen and that seem to complement what I'm looking for, but not exactly for the same age groups or with the same goals: Teaching Programming to Kids Recommendations for teaching kids math concepts & skills for programming?

  Read the article

• Replace dual-XP installs with single-XP install and repartition drive?

  - by caeious

  Hello, The Current Situation I have a hard drive that currently is split up like so: Primary Partition C: 9.77 GB NTFS Healthy (System) with XP Pro (in Polish) installed Extended Partition D: 39.82 GB NTFS Healthy (Boot) with XP Pro (in English) installed 6.30 GB Free space When I start my comuter I get a black and white Windows Boot Manager dual boot screen with 2 choices both being Microsoft Windows XP. The first choice is the English version of XP and the second choice is the Polish version of XP. Images of my Computer Management window and Dual Boot screen The Mission What I need to do is get rid of the entire extended partition (D: 39.82 GB & 6.30 free space) and just have the one primary C: drive which I assume will be somewheres around 55 GB big. So in the end I just want XP Pro in English running on my C: drive and no black and white boot screen to show up when starting up my laptop. The Question How do I go about successfully completing The Mission with out making my computer a useless pile of silicon, plastic and metal? UPDATE: So I went ahead and tried to follow Neal's suggestion but hit a wall. I got to a Windows XP Pro install screen that had the 3 following options as well as my drive data: To set up Windows XP on the selected item, press Enter To create a partition in the unpartitioned space, press C To delete the selected partition, press D 57232 MB Disk 0 at Id 0 on bus 0 on atapi [MBR] C: Partition1 [NTFS] 10001 MB ( 4642 MB free ) Unpartitioned space 6448 MB D: Partition2 [NTFS] 40774 MB ( 26225 MB free ) Unpartitioned space 8 MB I figured I would go with the first choice ((To set up Windows XP on the selected item, press Enter)) because I just wanted to set up Windows XP on C: Partition1 (which was preselected) so I pressed Enter which brought me to a screen displaying this message: You chose to install Windows XP on a partition that contains another operating system. Installing Windows XP on this partition might cause the other operating system to function improperly. CAUTION: Installing multiple operating systems on a single partition is not recommended. So this leads me to 2 new questions: How do I get rid of the Windows XP (Polish language) install on C: Partition 1 so that I can cleanly and safely install Windows XP (English language) on it? Neal, is this what you meant by me possibly having to delete the partition that the Windows XP (Polish language) install was located on? Since I have the option to delete partitions with the 3rd choice ((To delete the selected partition, press D)), should I do that on this screen or wait until I have Windows XP (English language) safely installed on C: Partition 1? I have to ask these questions because I have read that it is possibly dangerous to delete hard drive partitions. Just being cautious.

  Read the article

• Using Supermicro IPMI behind a Proxy?

  - by Stefan Lasiewski

  This is a SuperMicro server with a X8DT3 motherboard which contains an On-board IPMI BMC. In this case, the BMC is a Winbond WPCM450). I believe many Dell servers use this a similar BMC model. A common practice with IPMI is to isolated it to a private, non-routable network. In our case all IPMI cards are plugged into a private management LAN at 192.168.1.0/24 which has no route to the outside world. If I plug my laptop into the 192.168.1.0/24 network, I can verify that all IPMI features work as expected, including the remote console. I need to access all of the IPMI features from a different network, over some sort of encrypted connection. I tried SSH port forwarding. This works fine for a few servers, however, we have close to 100 of these servers and maintaining a SSH client configuration to forward 6 ports on 100 servers is impractical. So I thought I would try a SOCKS proxy. This works, but it seems that the Remote Console application does not obey my systemwide proxy settings. I setup a SOCKS proxy. Verbose logging allows me to see network activity, and if ports are being forwarded. ssh -v -D 3333 [email protected] I configure my system to use the SOCKS proxy. I confirm that Java is using the SOCKS proxy settings. The SOCKS proxy is working. I connect to the BMC at http://192.168.1.100/ using my webbrowser. I can log in, view the Server Health, power the machine on or off, etc. Since SSH verbose logging is enabled, I can see the progress. Here's where it get's tricky: I click on the "Launch Console" button which downloads a file called jviewer.jnlp. JNLP files are opened with Java Web Start. A Java window opens. The titlebar says says "Redirection Viewer" in the title bar. There are menus for "Video" "Keyboard" "Mouse", etc. This confirms that Java is able to download the application through the proxy, and start the application. 60 seconds later, the application times out and simply says "Error opening video socket". Here's a screenshot. If this worked, I would see a VNC-style window. My SSH logs show no connection attempts to ports 5900/5901. This suggests that the Java application started the VNC application, but that the VNC application ignores the systemwide proxy settings and is thus unable to connect to the remote host. Java seems to obey my systemwide proxy settings, but this VNC application seems to ignore it. Is there any way for me to force this VNC application to use my systemwide proxy settings?

  Read the article

• How to debug Ubuntu/Cisco VPN issues

  - by Joe Casadonte

  I'm trying to connect an Ubuntu laptop (9.10) with some kind of Cisco VPN device; I don't know what's on the other end, and I'm not likely to find out exactly what. I know my company allows VPN from Linux clients because they provide one that I cannot get to install (it fails to compile). I've had the most luck with the network-manager-vpnc package, however I can't figure out what's failing. When I try to connect, I get this message from libnotify: The VPN connection 'XXX' failed. which is not very helpful. I've scoured the system logs and all I can find is this: Dec 27 12:57:45 jcasadon-lap NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.vpnc'... Dec 27 12:57:45 jcasadon-lap NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.vpnc' started (org.freedesktop.NetworkManager.vpnc), PID 2672 Dec 27 12:57:45 jcasadon-lap NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.vpnc' just appeared, activating connections Dec 27 12:58:00 jcasadon-lap NetworkManager: <info> VPN plugin state changed: 3 Dec 27 12:58:00 jcasadon-lap NetworkManager: <info> VPN connection 'AmericasEast' (Connect) reply received. Dec 27 12:58:00 jcasadon-lap NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/tun0, iface: tun0) Dec 27 12:58:00 jcasadon-lap kernel: [ 6144.529002] tun0: Disabled Privacy Extensions Dec 27 12:58:00 jcasadon-lap NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/tun0, iface: tun0): no ifupdown configuration found. Dec 27 12:58:15 jcasadon-lap NetworkManager: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/tun0, iface: tun0) Dec 27 12:58:15 jcasadon-lap NetworkManager: <info> VPN plugin failed: 1 Dec 27 12:58:15 jcasadon-lap NetworkManager: <info> VPN plugin state changed: 6 Dec 27 12:58:15 jcasadon-lap NetworkManager: <info> VPN plugin state change reason: 0 Dec 27 12:58:15 jcasadon-lap NetworkManager: <WARN> connection_state_changed(): Could not process the request because no VPN connection was active. Dec 27 12:58:15 jcasadon-lap NetworkManager: <info> (wlan0): writing resolv.conf to /sbin/resolvconf Dec 27 12:58:15 jcasadon-lap NetworkManager: <info> Policy set 'Northbound Train' (wlan0) as default for routing and DNS. Dec 27 12:58:27 jcasadon-lap NetworkManager: <debug> [1261936707.002971] ensure_killed(): waiting for vpn service pid 2672 to exit Dec 27 12:58:27 jcasadon-lap NetworkManager: <debug> [1261936707.003175] ensure_killed(): vpn service pid 2672 cleaned up I have no idea where to go from here. Tomorrow I'll ask the IT/IS guys if there's anything they can tell me from their end, but I don't know if they'll be able to tell me anything. Any ideas? Thanks!

  Read the article

• Fedora 12 Wireless problems (Intel Wireless 4965AGN Card)

  - by Ninefingers

  Hi All, I'm having an interesting experience with my wireless card at the moment. Basically, it does like this: I connect to the local wireless network (netgear router) It works, briefly, allowing me to browse a webpage or maybe two, if I'm lucky. It then stops working / sending any packets, whilst reported still connected. Now, me being me I've had a look to see what I can find. wpa_supplicant.log looks like this: Trying to associate with valid_mac:a2:30 (SSID='vennardwireless' freq=2462 MHz) Associated with valid_mac:a2:30 WPA: Key negotiation completed with valid_mac:a2:30 [PTK=CCMP GTK=TKIP] CTRL-EVENT-CONNECTED - Connection to valid_mac:a2:30 completed (reauth) [id=0 id_str=] CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys So that's working fine. dmesg | grep "*iwl*" spits out this: iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 iwlagn 0000:03:00.0: setting latency timer to 64 iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 Registered led device: iwl-phy0::radio Registered led device: iwl-phy0::assoc Registered led device: iwl-phy0::RX Registered led device: iwl-phy0::TX iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 So that's working too. I can also ping 192.168.0.1 -I wlan0 and arping 192.168.0.1 -I wlan0 the router until the network falls over. uname -r:2.6.32.10-90.fc12.x86_64. Laptop is a Core2 Duo (2Ghz) with 3GB RAM. Other symptoms I've noticed are that wireshark freezes when I capture on the "broken" interface until I disconnect. Am using networkmanager as per normal. Stupidly, I can connect to the same router via eth0/a cat6 cable just fine. Everyone else can connect to the AP fine (from Windows). Yes, I'm sat right next to it and not trying to access a hotspot the other side of the world. Any ideas? Is this a broken update? (I intend to reboot and test an older kernel later)? Anyone else come across this? Edit: iwconfig wlan0 rate auto is the settings I'm using for rates. Also, according to networkmanager the network is still connected. Thanks for any pointers / advice.

  Read the article

• Cannot install virtualbox-ose-guest-dkms on Ubuntu 10.04

  - by mrduongnv

  I'm using Ubuntu 10.04 and kernel: 2.6.38-11-generic-pae. While using VirtualBox, i got this error: Kernel driver not installed (rc=-1908) Please install the virtualbox-ose-dkms package and execute 'modprobe vboxdrv' as root. I tried to execute the command: sudo modprobe vboxdrv and got this error: FATAL: Module vboxdrv not found. After that, i execute this: sudo aptitude install virtualbox-ose-guest-dkms duongnv@duongnv-laptop:~$ sudo aptitude install virtualbox-ose-guest-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done The following partially installed packages will be configured: virtualbox-ose-guest-dkms 0 packages upgraded, 0 newly installed, 0 to remove and 105 not upgraded. Need to get 0B of archives. After unpacking 0B will be used. Writing extended state information... Done Setting up virtualbox-ose-guest-dkms (3.1.6-dfsg-2ubuntu2) ... Removing old virtualbox-ose-guest-3.1.6 DKMS files... ------------------------------ Deleting module version: 3.1.6 completely from the DKMS tree. ------------------------------ Done. Loading new virtualbox-ose-guest-3.1.6 DKMS files... First Installation: checking all kernels... Building only for 2.6.38-11-generic-pae Building for architecture i686 Building initial module for 2.6.38-11-generic-pae Error! Bad return status for module build on kernel: 2.6.38-11-generic-pae (i686) Consult the make.log in the build directory /var/lib/dkms/virtualbox-ose-guest/3.1.6/build/ for more information. dpkg: error processing virtualbox-ose-guest-dkms (--configure): subprocess installed post-installation script returned error exit status 10 Errors were encountered while processing: virtualbox-ose-guest-dkms E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up virtualbox-ose-guest-dkms (3.1.6-dfsg-2ubuntu2) ... Removing old virtualbox-ose-guest-3.1.6 DKMS files... ------------------------------ Deleting module version: 3.1.6 completely from the DKMS tree. ------------------------------ Done. Loading new virtualbox-ose-guest-3.1.6 DKMS files... First Installation: checking all kernels... Building only for 2.6.38-11-generic-pae Building for architecture i686 Building initial module for 2.6.38-11-generic-pae Error! Bad return status for module build on kernel: 2.6.38-11-generic-pae (i686) Consult the make.log in the build directory /var/lib/dkms/virtualbox-ose-guest/3.1.6/build/ for more information. dpkg: error processing virtualbox-ose-guest-dkms (--configure): subprocess installed post-installation script returned error exit status 10 Errors were encountered while processing: virtualbox-ose-guest-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done

  Read the article

• Windows 7 extremely slow login, exchange performance, printer enumeration, etc...

  - by Jeff

  Background: I have a fresh copy of Windows 7 Professional x64 on a Dell Latitude E6500. The laptop has 8GB RAM, 250GB drive, and all Intel peripherals (net/wifi/graphics). All available Windows updates, as well as hardware drivers are installed. The IT folks where I work joined the computer to our Windows 2003-based Active Directory domain. There are no errors in any logs that we've looked at, and Group Policy templates appear to have applied properly. Problem: Every time I turn on or reboot the computer, it takes between 2 to 10 (all times are actual) minutes after successfully typing my username/password to get to my desktop. My login script does not always run. Sometimes I get a black screen, and a couple of minutes later the login script will pop up and take up to 10 minutes to complete. I can get around this by hitting cntrl-shift-esc and running explorer.exe from the Task Manager. The login script continues to hang, but I can minimize it and go on about my business. Either way, it generally throws errors prior to completing. I often get slow or failed connectivity to Exchange via Outlook. When I bring up printer dialogs, they take several minutes to populate, and block the calling app while doing so. Copies to SMB shares are very slow. On my home network, everything works fine. On both the work network and home network, I can use remote internet resources just fine. Web pages pull up, remote VPN's are fine, I can max out bandwidth on SpeakEasy Speed Test. I can get almost max bandwidth transferring FTP/HTTP over a LAN. Another symptom of the problem is that when I first log in, the work network shows as "Identifying" for a long time in the Network and Sharing Center, and will often then change to the name of the work domain, but say "Unauthenticated Network". Note that this computer previously ran Windows Vista with none of these problems. Attempts to Fix: Installed the Win7 admin pack Uninstalled/reinstalled all hardware drivers Verified Active Directory DNS settings (Vista works relatively well on the same network) Reset all TCP/IP settings on all adapters using the netsh commands to do so Disabled ipv6 on all adapters Disable wifi adapter while on work network Locked the network card to 100/Full, 1000/Full; also tried Auto Added various important addresses to hosts file (exchange, dns, ad) -- removed when didn't help My background is a jpeg (sounds unrelated but there is apparently a win7 login bug related to solid color background) More I have forgotten The IT staff at my company indicated they believe this is due to having Windows 2003 AD servers and not having any Windows 2008 R2 AD servers. Other than that, they have no advice or assistance to offer other than a rebuild (already tried that once with similar symptoms), or downgrade to Vista. Any thoughts out there?

  Read the article

< Previous Page | 320 321 322 323 324 325 326 327 328 329 330 331  | Next Page >